| 1 |
// SPDX-License-Identifier: GPL-2.0+ |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include "aspeed-g5.dtsi" |
| 5 |
#include <dt-bindings/gpio/aspeed-gpio.h> |
| 6 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 7 |
|
| 8 |
/ { |
| 9 |
model = "Tyan S7106 BMC"; |
| 10 |
compatible = "tyan,s7106-bmc", "aspeed,ast2500"; |
| 11 |
|
| 12 |
chosen { |
| 13 |
stdout-path = &uart5; |
| 14 |
bootargs = "console=ttyS4,115200 earlycon"; |
| 15 |
}; |
| 16 |
|
| 17 |
memory@80000000 { |
| 18 |
device_type = "memory"; |
| 19 |
reg = <0x80000000 0x20000000>; |
| 20 |
}; |
| 21 |
|
| 22 |
reserved-memory { |
| 23 |
#address-cells = <1>; |
| 24 |
#size-cells = <1>; |
| 25 |
ranges; |
| 26 |
|
| 27 |
p2a_memory: region@987f0000 { |
| 28 |
no-map; |
| 29 |
reg = <0x987f0000 0x00010000>; /* 64KB */ |
| 30 |
}; |
| 31 |
|
| 32 |
vga_memory: framebuffer@9f000000 { |
| 33 |
no-map; |
| 34 |
reg = <0x9f000000 0x01000000>; /* 16M */ |
| 35 |
}; |
| 36 |
|
| 37 |
gfx_memory: framebuffer { |
| 38 |
size = <0x01000000>; /* 16M */ |
| 39 |
alignment = <0x01000000>; |
| 40 |
compatible = "shared-dma-pool"; |
| 41 |
reusable; |
| 42 |
}; |
| 43 |
}; |
| 44 |
|
| 45 |
leds { |
| 46 |
compatible = "gpio-leds"; |
| 47 |
|
| 48 |
identify { |
| 49 |
gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>; |
| 50 |
}; |
| 51 |
|
| 52 |
heartbeat { |
| 53 |
gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>; |
| 54 |
}; |
| 55 |
}; |
| 56 |
|
| 57 |
iio-hwmon { |
| 58 |
compatible = "iio-hwmon"; |
| 59 |
io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, |
| 60 |
<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>, |
| 61 |
<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>, |
| 62 |
<&adc 12>, <&adc 13>, <&adc 14>; |
| 63 |
}; |
| 64 |
|
| 65 |
iio-hwmon-battery { |
| 66 |
compatible = "iio-hwmon"; |
| 67 |
io-channels = <&adc 15>; |
| 68 |
}; |
| 69 |
}; |
| 70 |
|
| 71 |
&fmc { |
| 72 |
status = "okay"; |
| 73 |
flash@0 { |
| 74 |
label = "bmc"; |
| 75 |
status = "okay"; |
| 76 |
m25p,fast-read; |
| 77 |
#include "openbmc-flash-layout.dtsi" |
| 78 |
}; |
| 79 |
}; |
| 80 |
|
| 81 |
&spi1 { |
| 82 |
status = "okay"; |
| 83 |
pinctrl-names = "default"; |
| 84 |
pinctrl-0 = <&pinctrl_spi1_default>; |
| 85 |
|
| 86 |
flash@0 { |
| 87 |
status = "okay"; |
| 88 |
label = "pnor"; |
| 89 |
m25p,fast-read; |
| 90 |
}; |
| 91 |
}; |
| 92 |
|
| 93 |
&uart1 { |
| 94 |
/* Rear RS-232 connector */ |
| 95 |
status = "okay"; |
| 96 |
pinctrl-names = "default"; |
| 97 |
pinctrl-0 = <&pinctrl_txd1_default |
| 98 |
&pinctrl_rxd1_default>; |
| 99 |
}; |
| 100 |
|
| 101 |
&uart2 { |
| 102 |
/* RS-232 connector on header */ |
| 103 |
status = "okay"; |
| 104 |
pinctrl-names = "default"; |
| 105 |
pinctrl-0 = <&pinctrl_txd2_default |
| 106 |
&pinctrl_rxd2_default>; |
| 107 |
}; |
| 108 |
|
| 109 |
&uart3 { |
| 110 |
/* Alternative to vuart to internally connect (route) to uart1 |
| 111 |
* when vuart cannot be used due to BIOS limitations. |
| 112 |
*/ |
| 113 |
status = "okay"; |
| 114 |
}; |
| 115 |
|
| 116 |
&uart4 { |
| 117 |
/* Alternative to vuart to internally connect (route) to the |
| 118 |
* external port usually used by uart1 when vuart cannot be |
| 119 |
* used due to BIOS limitations. |
| 120 |
*/ |
| 121 |
status = "okay"; |
| 122 |
}; |
| 123 |
|
| 124 |
&uart5 { |
| 125 |
/* BMC "debug" (console) UART; connected to RS-232 connector |
| 126 |
* on header; selectable via jumpers as alternative to uart2 |
| 127 |
*/ |
| 128 |
status = "okay"; |
| 129 |
}; |
| 130 |
|
| 131 |
&uart_routing { |
| 132 |
status = "okay"; |
| 133 |
}; |
| 134 |
|
| 135 |
&vuart { |
| 136 |
status = "okay"; |
| 137 |
|
| 138 |
/* We enable the VUART here, but leave it in a state that does |
| 139 |
* not interfere with the SuperIO. The goal is to have both the |
| 140 |
* VUART and the SuperIO available and decide at runtime whether |
| 141 |
* the VUART should actually be used. For that reason, configure |
| 142 |
* an "invalid" IO address and an IRQ that is not used by the |
| 143 |
* BMC. |
| 144 |
*/ |
| 145 |
|
| 146 |
aspeed,lpc-io-reg = <0xffff>; |
| 147 |
aspeed,lpc-interrupts = <15 IRQ_TYPE_LEVEL_HIGH>; |
| 148 |
}; |
| 149 |
|
| 150 |
&lpc_ctrl { |
| 151 |
status = "okay"; |
| 152 |
}; |
| 153 |
|
| 154 |
&p2a { |
| 155 |
status = "okay"; |
| 156 |
memory-region = <&p2a_memory>; |
| 157 |
}; |
| 158 |
|
| 159 |
&lpc_snoop { |
| 160 |
status = "okay"; |
| 161 |
snoop-ports = <0x80>; |
| 162 |
}; |
| 163 |
|
| 164 |
&adc { |
| 165 |
status = "okay"; |
| 166 |
}; |
| 167 |
|
| 168 |
&vhub { |
| 169 |
status = "okay"; |
| 170 |
}; |
| 171 |
|
| 172 |
&pwm_tacho { |
| 173 |
status = "okay"; |
| 174 |
pinctrl-names = "default"; |
| 175 |
pinctrl-0 = <&pinctrl_pwm0_default |
| 176 |
&pinctrl_pwm1_default |
| 177 |
&pinctrl_pwm3_default |
| 178 |
&pinctrl_pwm4_default>; |
| 179 |
|
| 180 |
/* CPU fan #0 */ |
| 181 |
fan@0 { |
| 182 |
reg = <0x00>; |
| 183 |
aspeed,fan-tach-ch = /bits/ 8 <0x00>; |
| 184 |
}; |
| 185 |
|
| 186 |
/* CPU fan #1 */ |
| 187 |
fan@1 { |
| 188 |
reg = <0x01>; |
| 189 |
aspeed,fan-tach-ch = /bits/ 8 <0x01>; |
| 190 |
}; |
| 191 |
|
| 192 |
/* PWM group for chassis fans #1, #2, #3 and #4 */ |
| 193 |
fan@2 { |
| 194 |
reg = <0x03>; |
| 195 |
aspeed,fan-tach-ch = /bits/ 8 <0x02>; |
| 196 |
}; |
| 197 |
|
| 198 |
fan@3 { |
| 199 |
reg = <0x03>; |
| 200 |
aspeed,fan-tach-ch = /bits/ 8 <0x03>; |
| 201 |
}; |
| 202 |
|
| 203 |
fan@4 { |
| 204 |
reg = <0x03>; |
| 205 |
aspeed,fan-tach-ch = /bits/ 8 <0x04>; |
| 206 |
}; |
| 207 |
|
| 208 |
fan@5 { |
| 209 |
reg = <0x03>; |
| 210 |
aspeed,fan-tach-ch = /bits/ 8 <0x05>; |
| 211 |
}; |
| 212 |
|
| 213 |
/* PWM group for chassis fans #5 and #6 */ |
| 214 |
fan@6 { |
| 215 |
reg = <0x04>; |
| 216 |
aspeed,fan-tach-ch = /bits/ 8 <0x06>; |
| 217 |
}; |
| 218 |
|
| 219 |
fan@7 { |
| 220 |
reg = <0x04>; |
| 221 |
aspeed,fan-tach-ch = /bits/ 8 <0x07>; |
| 222 |
}; |
| 223 |
}; |
| 224 |
|
| 225 |
&i2c0 { |
| 226 |
status = "okay"; |
| 227 |
|
| 228 |
/* Hardware monitor with temperature sensors */ |
| 229 |
nct7802@28 { |
| 230 |
compatible = "nuvoton,nct7802"; |
| 231 |
reg = <0x28>; |
| 232 |
|
| 233 |
#address-cells = <1>; |
| 234 |
#size-cells = <0>; |
| 235 |
|
| 236 |
channel@0 { /* LTD */ |
| 237 |
reg = <0>; |
| 238 |
}; |
| 239 |
|
| 240 |
channel@1 { /* RTD1 */ |
| 241 |
reg = <1>; |
| 242 |
sensor-type = "temperature"; |
| 243 |
temperature-mode = "thermistor"; |
| 244 |
}; |
| 245 |
|
| 246 |
channel@2 { /* RTD2 */ |
| 247 |
reg = <2>; |
| 248 |
sensor-type = "temperature"; |
| 249 |
temperature-mode = "thermistor"; |
| 250 |
}; |
| 251 |
|
| 252 |
channel@3 { /* RTD3 */ |
| 253 |
reg = <3>; |
| 254 |
sensor-type = "temperature"; |
| 255 |
}; |
| 256 |
}; |
| 257 |
|
| 258 |
/* Also connected to: |
| 259 |
* - IPMB pin header |
| 260 |
* - CPU #0 memory error LED @ 0x3A |
| 261 |
* - CPU #1 memory error LED @ 0x3C |
| 262 |
*/ |
| 263 |
}; |
| 264 |
|
| 265 |
&i2c1 { |
| 266 |
/* Directly connected to PCH SMBUS #0 */ |
| 267 |
status = "okay"; |
| 268 |
}; |
| 269 |
|
| 270 |
&i2c2 { |
| 271 |
status = "okay"; |
| 272 |
|
| 273 |
/* BMC EEPROM, incl. mainboard FRU */ |
| 274 |
eeprom@50 { |
| 275 |
compatible = "atmel,24c256"; |
| 276 |
reg = <0x50>; |
| 277 |
}; |
| 278 |
|
| 279 |
/* Also connected to: |
| 280 |
* - fan header |
| 281 |
* - mini-SAS HD connector |
| 282 |
* - SSATA SGPIO |
| 283 |
* - via switch (BMC_SMB3_PCH_IE_SML3_EN, active low) |
| 284 |
* to PCH SMBUS #3 |
| 285 |
*/ |
| 286 |
}; |
| 287 |
|
| 288 |
&i2c3 { |
| 289 |
status = "okay"; |
| 290 |
|
| 291 |
/* PSU1 FRU @ 0xA0 */ |
| 292 |
eeprom@50 { |
| 293 |
compatible = "atmel,24c02"; |
| 294 |
reg = <0x50>; |
| 295 |
}; |
| 296 |
|
| 297 |
/* PSU2 FRU @ 0xA2 */ |
| 298 |
eeprom@51 { |
| 299 |
compatible = "atmel,24c02"; |
| 300 |
reg = <0x51>; |
| 301 |
}; |
| 302 |
|
| 303 |
/* PSU1 @ 0xB0 */ |
| 304 |
power-supply@58 { |
| 305 |
compatible = "pmbus"; |
| 306 |
reg = <0x58>; |
| 307 |
}; |
| 308 |
|
| 309 |
/* PSU2 @ 0xB2 */ |
| 310 |
power-supply@59 { |
| 311 |
compatible = "pmbus"; |
| 312 |
reg = <0x59>; |
| 313 |
}; |
| 314 |
|
| 315 |
/* Also connected to: |
| 316 |
* - PCH SMBUS #1 |
| 317 |
*/ |
| 318 |
}; |
| 319 |
|
| 320 |
&i2c4 { |
| 321 |
status = "okay"; |
| 322 |
|
| 323 |
/* Connected to: |
| 324 |
* - PCH SMBUS #2 |
| 325 |
*/ |
| 326 |
|
| 327 |
/* Connected via switch to: |
| 328 |
* - CPU #0 channels ABC VDDQ @ 0x80 |
| 329 |
* - CPU #0 channels DEF VDDQ @ 0x81 |
| 330 |
* - CPU #1 channels ABC VDDQ @ 0x82 |
| 331 |
* - CPU #1 channels DEF VDDQ @ 0x83 |
| 332 |
* - CPU #0 VCCIO & VMCP @ 0x52 |
| 333 |
* - CPU #1 VCCIO & VMCP @ 0x53 |
| 334 |
* - CPU #0 VCCIN @ 0xC0 |
| 335 |
* - CPU #0 VSA @ 0xC2 |
| 336 |
* - CPU #1 VCCIN @ 0xC4 |
| 337 |
* - CPU #1 VSA @ 0xC6 |
| 338 |
* - J110 |
| 339 |
*/ |
| 340 |
}; |
| 341 |
|
| 342 |
&i2c5 { |
| 343 |
status = "okay"; |
| 344 |
|
| 345 |
/* Connected via switch (PCH_BMC_SMB_SW_P) to: |
| 346 |
* - mainboard FRU @ 0xAE |
| 347 |
* - XDP connector |
| 348 |
* - ME debug header |
| 349 |
* - clock buffer @ 0xD8 |
| 350 |
* - i2c4 via switch (PCH_VR_SMBUS_SW_P; controlled by PCH) |
| 351 |
* - PCH SMBUS |
| 352 |
*/ |
| 353 |
}; |
| 354 |
|
| 355 |
&i2c6 { |
| 356 |
status = "okay"; |
| 357 |
|
| 358 |
/* Connected via switch (BMC_PE_SMB_EN_1_N) to |
| 359 |
* bus mux (selector BMC_PE_SMB_SW_BIT[1..0]) to: |
| 360 |
* - 0,0: PCIE slot 1, SMB #1 |
| 361 |
* - 0,1: PCIE slot 1, SMB #2 |
| 362 |
* - 1,0: PCIE slot 2, SMB #1 |
| 363 |
* - 1,1: PCIE slot 2, SMB #2 |
| 364 |
*/ |
| 365 |
|
| 366 |
/* Connected via switch (BMC_PE_SMB_EN_2_N) to |
| 367 |
* bus mux (selector BMC_PE_SMB_SW_BIT[1..0]) to: |
| 368 |
* - 0,0: OCP0 (A) SMB |
| 369 |
* - 0,1: OCP0 (C) SMB |
| 370 |
* - 1,0: OCP1 (A) SMB |
| 371 |
* - 1,1: NC |
| 372 |
*/ |
| 373 |
}; |
| 374 |
|
| 375 |
&i2c7 { |
| 376 |
status = "okay"; |
| 377 |
|
| 378 |
/* Connected to: |
| 379 |
* - PCH SMBUS #4 |
| 380 |
*/ |
| 381 |
}; |
| 382 |
|
| 383 |
&i2c8 { |
| 384 |
status = "okay"; |
| 385 |
|
| 386 |
/* Not connected */ |
| 387 |
}; |
| 388 |
|
| 389 |
&mac0 { |
| 390 |
status = "okay"; |
| 391 |
use-ncsi; |
| 392 |
pinctrl-names = "default"; |
| 393 |
pinctrl-0 = <&pinctrl_rmii1_default>; |
| 394 |
}; |
| 395 |
|
| 396 |
&mac1 { |
| 397 |
status = "okay"; |
| 398 |
pinctrl-names = "default"; |
| 399 |
pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>; |
| 400 |
}; |
| 401 |
|
| 402 |
&ibt { |
| 403 |
status = "okay"; |
| 404 |
}; |
| 405 |
|
| 406 |
&kcs1 { |
| 407 |
status = "okay"; |
| 408 |
aspeed,lpc-io-reg = <0xca8>; |
| 409 |
}; |
| 410 |
|
| 411 |
&kcs3 { |
| 412 |
status = "okay"; |
| 413 |
aspeed,lpc-io-reg = <0xca2>; |
| 414 |
}; |
| 415 |
|
| 416 |
/* Enable BMC VGA output to show an early (pre-BIOS) boot screen */ |
| 417 |
&gfx { |
| 418 |
status = "okay"; |
| 419 |
memory-region = <&gfx_memory>; |
| 420 |
}; |
| 421 |
|
| 422 |
/* We're following the GPIO naming as defined at |
| 423 |
* https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md. |
| 424 |
* |
| 425 |
* Notes on led-identify and id-button: |
| 426 |
* - A physical button is connected to id-button which |
| 427 |
* triggers the clock on a D flip-flop. The /Q output of the |
| 428 |
* flip-flop drives its D input. |
| 429 |
* - The flip-flop's Q output drives led-identify which is |
| 430 |
* connected to LEDs. |
| 431 |
* - With that, every button press toggles the LED between on and off. |
| 432 |
* |
| 433 |
* Notes on power-, reset- and nmi- button and control: |
| 434 |
* - The -button signals can be used to monitor physical buttons. |
| 435 |
* - The -control signals can be used to actuate the specific |
| 436 |
* operation. |
| 437 |
* - In hardware, the -button signals are connected to the -control |
| 438 |
* signals through drivers with the -control signals being |
| 439 |
* protected through diodes. |
| 440 |
*/ |
| 441 |
&gpio { |
| 442 |
status = "okay"; |
| 443 |
gpio-line-names = |
| 444 |
/*A0*/ "", |
| 445 |
/*A1*/ "", |
| 446 |
/*A2*/ "led-identify", /* in/out: BMC_IDLED_ON_N */ |
| 447 |
/*A3*/ "", |
| 448 |
/*A4*/ "", |
| 449 |
/*A5*/ "", |
| 450 |
/*A6*/ "", |
| 451 |
/*A7*/ "", |
| 452 |
/*B0-B7*/ "","","","","","","","", |
| 453 |
/*C0*/ "", |
| 454 |
/*C1*/ "", |
| 455 |
/*C2*/ "", |
| 456 |
/*C3*/ "", |
| 457 |
/*C4*/ "id-button", /* in/out: BMC_IDBTN_IN_OUT_N */ |
| 458 |
/*C5*/ "post-complete", /* in: FM_BIOS_POST_CMPLT_N */ |
| 459 |
/*C6*/ "", |
| 460 |
/*C7*/ "", |
| 461 |
/*D0*/ "", |
| 462 |
/*D1*/ "", |
| 463 |
/*D2*/ "power-chassis-good", /* in: SYS_PWROK_BUF */ |
| 464 |
/*D3*/ "platform-reset", /* in: SYS_PLTRST_N */ |
| 465 |
/*D4*/ "", |
| 466 |
/*D5*/ "", |
| 467 |
/*D6*/ "", |
| 468 |
/*D7*/ "", |
| 469 |
/*E0*/ "power-button", /* in: BMC_PWBTN_IN_N */ |
| 470 |
/*E1*/ "power-chassis-control", /* out: BMC_PWRBTN_OUT_N */ |
| 471 |
/*E2*/ "reset-button", /* in: BMC_RSTBTN_IN_N */ |
| 472 |
/*E3*/ "reset-control", /* out: BMC_RSTBTN_OUT_N */ |
| 473 |
/*E4*/ "nmi-button", /* in: BMC_NMIBTN_IN_N */ |
| 474 |
/*E5*/ "nmi-control", /* out: BMC_NMIBTN_OUT_N */ |
| 475 |
/*E6*/ "", |
| 476 |
/*E7*/ "led-heartbeat", /* out: BMC_HEARTBRAT_LED_N */ |
| 477 |
/*F0*/ "", |
| 478 |
/*F1*/ "clear-cmos-control", /* out: BMC_CLR_CMOS_N */ |
| 479 |
/*F2*/ "", |
| 480 |
/*F3*/ "", |
| 481 |
/*F4*/ "led-fault", /* out: AST_HW_FAULT_N */ |
| 482 |
/*F5*/ "", |
| 483 |
/*F6*/ "", |
| 484 |
/*F7*/ "", |
| 485 |
/*G0*/ "BMC_PE_SMB_EN_1_N", /* out */ |
| 486 |
/*G1*/ "BMC_PE_SMB_EN_2_N", /* out */ |
| 487 |
/*G2*/ "", |
| 488 |
/*G3*/ "", |
| 489 |
/*G4*/ "", |
| 490 |
/*G5*/ "", |
| 491 |
/*G6*/ "", |
| 492 |
/*G7*/ "", |
| 493 |
/*H0-H7*/ "","","","","","","","", |
| 494 |
/*I0-I7*/ "","","","","","","","", |
| 495 |
/*J0-J7*/ "","","","","","","","", |
| 496 |
/*K0-K7*/ "","","","","","","","", |
| 497 |
/*L0-L7*/ "","","","","","","","", |
| 498 |
/*M0-M7*/ "","","","","","","","", |
| 499 |
/*N0-N7*/ "","","","","","","","", |
| 500 |
/*O0-O7*/ "","","","","","","","", |
| 501 |
/*P0-P7*/ "","","","","","","","", |
| 502 |
/*Q0*/ "", |
| 503 |
/*Q1*/ "", |
| 504 |
/*Q2*/ "", |
| 505 |
/*Q3*/ "", |
| 506 |
/*Q4*/ "BMC_PE_SMB_SW_BIT0", /* out */ |
| 507 |
/*Q5*/ "BMC_PE_SMB_SW_BIT1", /* out */ |
| 508 |
/*Q6*/ "", |
| 509 |
/*Q7*/ "", |
| 510 |
/*R0-R7*/ "","","","","","","","", |
| 511 |
/*S0-S7*/ "","","","","","","","", |
| 512 |
/*T0-T7*/ "","","","","","","","", |
| 513 |
/*U0-U7*/ "","","","","","","","", |
| 514 |
/*V0-V7*/ "","","","","","","","", |
| 515 |
/*W0-W7*/ "","","","","","","","", |
| 516 |
/*X0-X7*/ "","","","","","","","", |
| 517 |
/*Y0-Y7*/ "","","","","","","","", |
| 518 |
/*Z0-Z7*/ "","","","","","","","", |
| 519 |
/*AA0*/ "", |
| 520 |
/*AA1*/ "", |
| 521 |
/*AA2*/ "", |
| 522 |
/*AA3*/ "BMC_SMB3_PCH_IE_SML3_EN", /* out */ |
| 523 |
/*AA4*/ "", |
| 524 |
/*AA5*/ "", |
| 525 |
/*AA6*/ "", |
| 526 |
/*AA7*/ "", |
| 527 |
/*AB0-AB7*/ "","","","","","","",""; |
| 528 |
}; |