Debian Codegraph @

arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts

raw
1 // SPDX-License-Identifier: GPL-2.0+
2 /dts-v1/;
3
4 #include "aspeed-g6.dtsi"
5 #include <dt-bindings/i2c/i2c.h>
6 #include <dt-bindings/gpio/aspeed-gpio.h>
7 #include <dt-bindings/leds/common.h>
8
9 / {
10 model = "AST2600 GB200NVL BMC";
11 compatible = "nvidia,gb200nvl-bmc", "aspeed,ast2600";
12
13 aliases {
14 serial2 = &uart3;
15 serial4 = &uart5;
16 i2c16 = &imux16;
17 i2c17 = &imux17;
18 i2c18 = &imux18;
19 i2c19 = &imux19;
20 i2c20 = &imux20;
21 i2c21 = &imux21;
22 i2c22 = &imux22;
23 i2c23 = &imux23;
24 i2c24 = &imux24;
25 i2c25 = &imux25;
26 i2c26 = &imux26;
27 i2c27 = &imux27;
28 i2c28 = &imux28;
29 i2c29 = &imux29;
30 i2c30 = &imux30;
31 i2c31 = &imux31;
32 i2c32 = &imux32;
33 i2c33 = &imux33;
34 i2c34 = &imux34;
35 i2c35 = &imux35;
36 i2c36 = &imux36;
37 i2c37 = &imux37;
38 i2c38 = &imux38;
39 i2c39 = &imux39;
40 i2c40 = &e1si2c0;
41 i2c41 = &e1si2c1;
42 i2c42 = &e1si2c2;
43 i2c43 = &e1si2c3;
44 i2c44 = &e1si2c4;
45 i2c45 = &e1si2c5;
46 i2c46 = &e1si2c6;
47 i2c47 = &e1si2c7;
48 i2c48 = &i2c17mux0;
49 i2c49 = &i2c17mux1;
50 i2c50 = &i2c17mux2;
51 i2c51 = &i2c17mux3;
52 i2c52 = &i2c25mux0;
53 i2c53 = &i2c25mux1;
54 i2c54 = &i2c25mux2;
55 i2c55 = &i2c25mux3;
56 i2c56 = &i2c29mux0;
57 i2c57 = &i2c29mux1;
58 i2c58 = &i2c29mux2;
59 i2c59 = &i2c29mux3;
60 };
61
62 chosen {
63 stdout-path = &uart5;
64 };
65
66 memory@80000000 {
67 device_type = "memory";
68 reg = <0x80000000 0x80000000>;
69 };
70
71 reserved-memory {
72 #address-cells = <1>;
73 #size-cells = <1>;
74 ranges;
75
76 vga_memory: framebuffer@9f000000 {
77 no-map;
78 reg = <0x9f000000 0x01000000>; /* 16M */
79 };
80
81 ramoops@a0000000 {
82 compatible = "ramoops";
83 reg = <0xa0000000 0x100000>; /* 1MB */
84 record-size = <0x10000>; /* 64KB */
85 max-reason = <2>; /* KMSG_DUMP_OOPS */
86 };
87
88 gfx_memory: framebuffer {
89 size = <0x01000000>;
90 alignment = <0x01000000>;
91 compatible = "shared-dma-pool";
92 reusable;
93 };
94
95 video_engine_memory: jpegbuffer {
96 size = <0x02000000>; /* 32M */
97 alignment = <0x01000000>;
98 compatible = "shared-dma-pool";
99 reusable;
100 };
101 };
102
103 leds {
104 compatible = "gpio-leds";
105 led-0 {
106 label = "uid_led";
107 gpios = <&sgpiom0 27 GPIO_ACTIVE_LOW>;
108 };
109 led-1 {
110 label = "fault_led";
111 gpios = <&sgpiom0 29 GPIO_ACTIVE_LOW>;
112 };
113 led-2 {
114 label = "power_led";
115 gpios = <&sgpiom0 31 GPIO_ACTIVE_LOW>;
116 };
117 };
118
119 buttons {
120 button-power {
121 label = "power-btn";
122 gpio = <&sgpiom0 156 GPIO_ACTIVE_LOW>;
123 };
124 button-uid {
125 label = "uid-btn";
126 gpio = <&sgpiom0 154 GPIO_ACTIVE_LOW>;
127 };
128 };
129
130 standby_power_regulator: standby-power-regulator {
131 status = "okay";
132 compatible = "regulator-fixed";
133 regulator-name = "standby_power";
134 gpio = <&gpio0 ASPEED_GPIO(M, 3) GPIO_ACTIVE_HIGH>;
135 regulator-min-microvolt = <1800000>;
136 regulator-max-microvolt = <1800000>;
137 enable-active-high;
138 regulator-always-on;
139 };
140 };
141
142 // Enable Primary flash on FMC for bring up activity
143 &fmc {
144 status = "okay";
145 flash@0 {
146 status = "okay";
147 compatible = "jedec,spi-nor";
148 label = "bmc";
149 spi-max-frequency = <50000000>;
150 partitions {
151 compatible = "fixed-partitions";
152 #address-cells = <1>;
153 #size-cells = <1>;
154
155 u-boot@0 {
156 // 896KB
157 reg = <0x0 0xe0000>;
158 label = "u-boot";
159 };
160
161 kernel@100000 {
162 // 9MB
163 reg = <0x100000 0x900000>;
164 label = "kernel";
165 };
166
167 rofs@a00000 {
168 // 55292KB (extends to end of 64MB SPI - 4KB)
169 reg = <0xa00000 0x35FF000>;
170 label = "rofs";
171 };
172 };
173 };
174 };
175
176 &spi2 {
177 status = "okay";
178 pinctrl-names = "default";
179 pinctrl-0 = <&pinctrl_spi2_default>;
180
181 // Data SPI is 64MB in size
182 flash@0 {
183 status = "okay";
184 label = "config";
185 spi-max-frequency = <50000000>;
186 partitions {
187 compatible = "fixed-partitions";
188 #address-cells = <1>;
189 #size-cells = <1>;
190
191 u-boot-env@0 {
192 // 256KB
193 reg = <0x0 0x40000>;
194 label = "u-boot-env";
195 };
196
197 rwfs@40000 {
198 // 16MB
199 reg = <0x40000 0x1000000>;
200 label = "rwfs";
201 };
202
203 log@1040000 {
204 // 40MB
205 reg = <0x1040000 0x2800000>;
206 label = "log";
207 };
208 };
209 };
210 };
211
212 &uart1 {
213 status = "okay";
214 };
215
216 &uart3 {
217 // Enabling SOL
218 status = "okay";
219 };
220
221 &uart5 {
222 // BMC Debug Console
223 status = "okay";
224 };
225
226 &uart_routing {
227 status = "okay";
228 };
229
230 &mdio0 {
231 status = "okay";
232 ethphy0: ethernet-phy@0 {
233 compatible = "ethernet-phy-ieee802.3-c22";
234 reg = <0>;
235 };
236 };
237
238 &mdio3 {
239 status = "okay";
240 ethphy3: ethernet-phy@2 {
241 compatible = "ethernet-phy-ieee802.3-c22";
242 reg = <2>;
243 };
244 };
245
246 &mac0 {
247 status = "okay";
248 pinctrl-names = "default";
249 phy-mode = "rgmii-id";
250 phy-handle = <&ethphy3>;
251 pinctrl-0 = <&pinctrl_rgmii1_default>;
252 };
253
254 &mac2 {
255 status = "okay";
256 phy-mode = "rmii";
257 use-ncsi;
258 pinctrl-names = "default";
259 pinctrl-0 = <&pinctrl_rmii3_default>;
260 };
261
262 /*
263 * Enable USB port A as device (via the virtual hub) to host
264 */
265 &vhub {
266 status = "okay";
267 };
268
269 &video {
270 status = "okay";
271 memory-region = <&video_engine_memory>;
272 };
273
274 // USB 2.0 to HMC, on USB Port B
275 &ehci1 {
276 status = "okay";
277 };
278
279 // USB 1.0
280 &uhci {
281 status = "okay";
282 };
283
284 &sgpiom0 {
285 status = "okay";
286 ngpios = <128>;
287 gpio-line-names =
288 "","",
289 "","",
290 "","",
291 "","",
292 "","",
293 "","",
294 "","",
295 "","",
296 "RUN_POWER_FAULT_L-I","SYS_RST_IN_L-O",
297 "RUN_POWER_PG-I","PWR_BRAKE_L-O",
298 "SYS_RST_OUT_L-I","RUN_POWER_EN-O",
299 "L0L1_RST_REQ_OUT_L-I","SHDN_FORCE_L-O",
300 "L2_RST_REQ_OUT_L-I","SHDN_REQ_L-O",
301 "SHDN_OK_L-I","UID_LED_N-O",
302 "BMC_I2C1_FPGA_ALERT_L-I","SYS_FAULT_LED_N-O",
303 "BMC_I2C0_FPGA_ALERT_L-I","PWR_LED_N-O",
304 "FPGA_RSVD_FFU3-I","",
305 "FPGA_RSVD_FFU2-I","",
306 "FPGA_RSVD_FFU1-I","",
307 "FPGA_RSVD_FFU0-I","BMC_I2C_SSIF_ALERT_L-O",
308 "CPU_BOOT_DONE-I","JTAG_MUX_SELECT-O",
309 "SPI_BMC_FPGA_INT_L-I","RTC_CLR_L-O",
310 "THERM_BB_WARN_L-I","UART_MUX_SEL-O",
311 "THERM_BB_OVERT_L-I","",
312 "CPU0_UPHY3_PRSNT1_L-I","IOBRD0_RUN_POWER_EN-O",
313 "CPU0_UPHY3_PRSNT0_L-I","IOBRD1_RUN_POWER_EN-O",
314 "CPU0_UPHY2_PRSNT1_L-I","FPGA_RSVD_FFU4-O",
315 "CPU0_UPHY2_PRSNT0_L-I","FPGA_RSVD_FFU5-O",
316 "CPU0_UPHY1_PRSNT1_L-I","FPGA_RSVD_FFU6-O",
317 "CPU0_UPHY1_PRSNT0_L-I","FPGA_RSVD_FFU7-O",
318 "CPU0_UPHY0_PRSNT1_L-I","RSVD_NV_PLT_DETECT-O",
319 "CPU0_UPHY0_PRSNT0_L-I","SPI1_INT_L-O",
320 "CPU1_UPHY3_PRSNT1_L-I","",
321 "CPU1_UPHY3_PRSNT0_L-I","HMC_EROT_MUX_STATUS",
322 "CPU1_UPHY2_PRSNT1_L-I","",
323 "CPU1_UPHY2_PRSNT0_L-I","",
324 "CPU1_UPHY1_PRSNT1_L-I","",
325 "CPU1_UPHY1_PRSNT0_L-I","",
326 "CPU1_UPHY0_PRSNT1_L-I","",
327 "CPU1_UPHY0_PRSNT0_L-I","",
328 "FAN1_PRESENT_L-I","",
329 "FAN0_PRESENT_L-I","",
330 "","",
331 "IPEX_CABLE_PRSNT_L-I","",
332 "M2_1_PRSNT_L-I","",
333 "M2_0_PRSNT_L-I","",
334 "CPU1_UPHY4_PRSNT1_L-I","",
335 "CPU0_UPHY4_PRSNT0_L-I","",
336 "","",
337 "I2C_RTC_ALERT_L-I","",
338 "FAN7_PRESENT_L-I","",
339 "FAN6_PRESENT_L-I","",
340 "FAN5_PRESENT_L-I","",
341 "FAN4_PRESENT_L-I","",
342 "FAN3_PRESENT_L-I","",
343 "FAN2_PRESENT_L-I","",
344 "IOBRD0_IOX_INT_L-I","",
345 "IOBRD1_PRSNT_L-I","",
346 "IOBRD0_PRSNT_L-I","",
347 "IOBRD1_PWR_GOOD-I","",
348 "IOBRD0_PWR_GOOD-I","",
349 "","",
350 "","",
351 "FAN_FAIL_IN_L-I","",
352 "","",
353 "","",
354 "","",
355 "PDB_CABLE_PRESENT_L-I","",
356 "","",
357 "CHASSIS_PWR_BRK_L-I","",
358 "","",
359 "IOBRD1_IOX_INT_L-I","",
360 "10GBE_SMBALRT_L-I","",
361 "PCIE_WAKE_L-I","",
362 "I2C_M21_ALERT_L-I","",
363 "I2C_M20_ALERT_L-I","",
364 "TRAY_FAST_SHDN_L-I","",
365 "UID_BTN_N-I","",
366 "PWR_BTN_L-I","",
367 "PSU_SMB_ALERT_L-I","",
368 "","",
369 "","",
370 "NODE_LOC_ID[0]-I","",
371 "NODE_LOC_ID[1]-I","",
372 "NODE_LOC_ID[2]-I","",
373 "NODE_LOC_ID[3]-I","",
374 "NODE_LOC_ID[4]-I","",
375 "NODE_LOC_ID[5]-I","",
376 "FAN10_PRESENT_L-I","",
377 "FAN9_PRESENT_L-I","",
378 "FAN8_PRESENT_L-I","",
379 "FPGA1_READY_HMC-I","",
380 "DP_HPD-I","",
381 "HMC_I2C3_FPGA_ALERT_L-I","",
382 "HMC_I2C2_FPGA_ALERT_L-I","",
383 "FPGA0_READY_HMC-I","",
384 "","",
385 "","",
386 "","",
387 "","",
388 "LEAK_DETECT_ALERT_L-I","",
389 "MOD1_B2B_CABLE_PRESENT_L-I","",
390 "MOD1_CLINK_CABLE_PRESENT_L-I","",
391 "FAN11_PRESENT_L-I","",
392 "","",
393 "","",
394 "","",
395 "","",
396 "","",
397 "","",
398 "","",
399 "","",
400 "","",
401 "","",
402 "","",
403 "","",
404 "","",
405 "","",
406 "","",
407 "","",
408 "RSVD_SGPIO_IN_CRC[0]","RSVD_SGPIO_O_CRC[7]",
409 "RSVD_SGPIO_IN_CRC[1]","RSVD_SGPIO_O_CRC[6]",
410 "RSVD_SGPIO_IN_CRC[2]","RSVD_SGPIO_O_CRC[5]",
411 "RSVD_SGPIO_IN_CRC[3]","RSVD_SGPIO_O_CRC[4]",
412 "RSVD_SGPIO_IN_CRC[4]","RSVD_SGPIO_O_CRC[3]",
413 "RSVD_SGPIO_IN_CRC[5]","RSVD_SGPIO_O_CRC[2]",
414 "RSVD_SGPIO_IN_CRC[6]","RSVD_SGPIO_O_CRC[1]",
415 "RSVD_SGPIO_IN_CRC[7]","RSVD_SGPIO_O_CRC[0]";
416 };
417
418 // I2C1, SSIF IPMI interface
419 &i2c0 {
420 status = "okay";
421 clock-frequency = <400000>;
422
423 ssif-bmc@10 {
424 compatible = "ssif-bmc";
425 reg = <0x10>;
426 };
427 };
428
429 // I2C2
430 // BMC_I2C1_FPGA - Secondary FPGA
431 // HMC EROT
432 &i2c1 {
433 status = "okay";
434 clock-frequency = <400000>;
435 multi-master;
436 };
437
438 // I2C3
439 // BMC_I2C0_FPGA - Primary FPGA
440 // HMC FRU EEPROM
441 &i2c2 {
442 status = "okay";
443 clock-frequency = <400000>;
444 multi-master;
445 };
446
447 // I2C4
448 &i2c3 {
449 status = "okay";
450 };
451
452 // I2C5
453 // RTC Driver
454 // IO Expander
455 &i2c4 {
456 status = "okay";
457 clock-frequency = <400000>;
458
459 // Module 0, Expander @0x21
460 exp4: gpio@21 {
461 compatible = "nxp,pca9555";
462 reg = <0x21>;
463 gpio-controller;
464 #gpio-cells = <2>;
465 interrupt-controller;
466 #interrupt-cells = <2>;
467 interrupt-parent = <&gpio1>;
468 interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
469 vcc-supply = <&standby_power_regulator>;
470 gpio-line-names =
471 "RTC_MUX_SEL-O",
472 "PCI_MUX_SEL-O",
473 "TPM_MUX_SEL-O",
474 "FAN_MUX-SEL-O",
475 "SGMII_MUX_SEL-O",
476 "DP_MUX_SEL-O",
477 "UPHY3_USB_SEL-O",
478 "NCSI_MUX_SEL-O",
479 "BMC_PHY_RST-O",
480 "RTC_CLR_L-O",
481 "BMC_12V_CTRL-O",
482 "PS_RUN_IO0_PG-I",
483 "",
484 "",
485 "",
486 "";
487 };
488 };
489
490 // I2C6
491 // Module 0/1 I2C MUX x3
492 &i2c5 {
493 status = "okay";
494 clock-frequency = <400000>;
495 multi-master;
496
497 i2c-mux@71 {
498 compatible = "nxp,pca9546";
499 #address-cells = <1>;
500 #size-cells = <0>;
501 reg = <0x71>;
502 i2c-mux-idle-disconnect;
503 vdd-supply = <&standby_power_regulator>;
504
505 imux16: i2c@0 {
506 #address-cells = <1>;
507 #size-cells = <0>;
508 reg = <0>;
509 };
510
511 imux17: i2c@1 {
512 #address-cells = <1>;
513 #size-cells = <0>;
514 reg = <1>;
515
516 i2c-mux@74 {
517 compatible = "nxp,pca9546";
518 #address-cells = <1>;
519 #size-cells = <0>;
520 reg = <0x74>;
521 i2c-mux-idle-disconnect;
522
523 i2c17mux0: i2c@0 {
524 #address-cells = <1>;
525 #size-cells = <0>;
526 reg = <0>;
527 };
528
529 i2c17mux1: i2c@1 {
530 #address-cells = <1>;
531 #size-cells = <0>;
532 reg = <1>;
533 };
534
535 i2c17mux2: i2c@2 {
536 #address-cells = <1>;
537 #size-cells = <0>;
538 reg = <2>;
539 };
540
541 i2c17mux3: i2c@3 {
542 #address-cells = <1>;
543 #size-cells = <0>;
544 reg = <3>;
545 };
546 };
547 };
548
549 imux18: i2c@2 {
550 #address-cells = <1>;
551 #size-cells = <0>;
552 reg = <2>;
553 };
554
555 imux19: i2c@3 {
556 #address-cells = <1>;
557 #size-cells = <0>;
558 reg = <3>;
559 };
560 };
561
562 i2c-mux@72 {
563 compatible = "nxp,pca9546";
564 #address-cells = <1>;
565 #size-cells = <0>;
566 reg = <0x72>;
567 i2c-mux-idle-disconnect;
568 vdd-supply = <&standby_power_regulator>;
569
570 imux20: i2c@0 {
571 #address-cells = <1>;
572 #size-cells = <0>;
573 reg = <0>;
574 };
575
576 imux21: i2c@1 {
577 #address-cells = <1>;
578 #size-cells = <0>;
579 reg = <1>;
580
581 gpio@21 {
582 compatible = "nxp,pca9555";
583 reg = <0x21>;
584 gpio-controller;
585 #gpio-cells = <2>;
586 vcc-supply = <&standby_power_regulator>;
587 gpio-line-names =
588 "RST_CX_0_L-O",
589 "RST_CX_1_L-O",
590 "CX0_SSD0_PRSNT_L-I",
591 "CX1_SSD1_PRSNT_L-I",
592 "CX_BOOT_CMPLT_CX0-I",
593 "CX_BOOT_CMPLT_CX1-I",
594 "CX_TWARN_CX0_L-I",
595 "CX_TWARN_CX1_L-I",
596 "CX_OVT_SHDN_CX0-I",
597 "CX_OVT_SHDN_CX1-I",
598 "FNP_L_CX0-O",
599 "FNP_L_CX1-O",
600 "",
601 "MCU_GPIO-I",
602 "MCU_RST_N-O",
603 "MCU_RECOVERY_N-O";
604 };
605 };
606
607 imux22: i2c@2 {
608 #address-cells = <1>;
609 #size-cells = <0>;
610 reg = <2>;
611 };
612
613 imux23: i2c@3 {
614 #address-cells = <1>;
615 #size-cells = <0>;
616 reg = <3>;
617 };
618 };
619
620 i2c-mux@73 {
621 compatible = "nxp,pca9546";
622 #address-cells = <1>;
623 #size-cells = <0>;
624 reg = <0x73>;
625 i2c-mux-idle-disconnect;
626 vdd-supply = <&standby_power_regulator>;
627
628 imux24: i2c@0 {
629 #address-cells = <1>;
630 #size-cells = <0>;
631 reg = <0>;
632 };
633
634 imux25: i2c@1 {
635 #address-cells = <1>;
636 #size-cells = <0>;
637 reg = <1>;
638
639 i2c-mux@70 {
640 compatible = "nxp,pca9546";
641 #address-cells = <1>;
642 #size-cells = <0>;
643 reg = <0x70>;
644 i2c-mux-idle-disconnect;
645 vdd-supply = <&standby_power_regulator>;
646
647 i2c25mux0: i2c@0 {
648 #address-cells = <1>;
649 #size-cells = <0>;
650 reg = <0>;
651 };
652
653 i2c25mux1: i2c@1 {
654 #address-cells = <1>;
655 #size-cells = <0>;
656 reg = <1>;
657 };
658
659 i2c25mux2: i2c@2 {
660 #address-cells = <1>;
661 #size-cells = <0>;
662 reg = <2>;
663 };
664
665 i2c25mux3: i2c@3 {
666 #address-cells = <1>;
667 #size-cells = <0>;
668 reg = <3>;
669 };
670 };
671 };
672
673 imux26: i2c@2 {
674 #address-cells = <1>;
675 #size-cells = <0>;
676 reg = <2>;
677 };
678
679 imux27: i2c@3 {
680 #address-cells = <1>;
681 #size-cells = <0>;
682 reg = <3>;
683 };
684 };
685
686 i2c-mux@75 {
687 compatible = "nxp,pca9546";
688 #address-cells = <1>;
689 #size-cells = <0>;
690 reg = <0x75>;
691 i2c-mux-idle-disconnect;
692 vdd-supply = <&standby_power_regulator>;
693
694 imux28: i2c@0 {
695 #address-cells = <1>;
696 #size-cells = <0>;
697 reg = <0>;
698 };
699
700 imux29: i2c@1 {
701 #address-cells = <1>;
702 #size-cells = <0>;
703 reg = <1>;
704
705 i2c-mux@74 {
706 compatible = "nxp,pca9546";
707 #address-cells = <1>;
708 #size-cells = <0>;
709 reg = <0x74>;
710 i2c-mux-idle-disconnect;
711
712 i2c29mux0: i2c@0 {
713 #address-cells = <1>;
714 #size-cells = <0>;
715 reg = <0>;
716 };
717
718 i2c29mux1: i2c@1 {
719 #address-cells = <1>;
720 #size-cells = <0>;
721 reg = <1>;
722 };
723
724 i2c29mux2: i2c@2 {
725 #address-cells = <1>;
726 #size-cells = <0>;
727 reg = <2>;
728 };
729
730 i2c29mux3: i2c@3 {
731 #address-cells = <1>;
732 #size-cells = <0>;
733 reg = <3>;
734 };
735 };
736 };
737
738 imux30: i2c@2 {
739 #address-cells = <1>;
740 #size-cells = <0>;
741 reg = <2>;
742 };
743
744 imux31: i2c@3 {
745 #address-cells = <1>;
746 #size-cells = <0>;
747 reg = <3>;
748 };
749 };
750
751 i2c-mux@76 {
752 compatible = "nxp,pca9546";
753 #address-cells = <1>;
754 #size-cells = <0>;
755 reg = <0x76>;
756 i2c-mux-idle-disconnect;
757 vdd-supply = <&standby_power_regulator>;
758
759 imux32: i2c@0 {
760 #address-cells = <1>;
761 #size-cells = <0>;
762 reg = <0>;
763 };
764
765 imux33: i2c@1 {
766 #address-cells = <1>;
767 #size-cells = <0>;
768 reg = <1>;
769
770 gpio@21 {
771 compatible = "nxp,pca9555";
772 reg = <0x21>;
773 gpio-controller;
774 #gpio-cells = <2>;
775 vcc-supply = <&standby_power_regulator>;
776 gpio-line-names =
777 "SEC_RST_CX_0_L-O",
778 "SEC_RST_CX_1_L-O",
779 "SEC_CX0_SSD0_PRSNT_L-I",
780 "SEC_CX1_SSD1_PRSNT_L-I",
781 "SEC_CX_BOOT_CMPLT_CX0-I",
782 "SEC_CX_BOOT_CMPLT_CX1-I",
783 "SEC_CX_TWARN_CX0_L-I",
784 "SEC_CX_TWARN_CX1_L-I",
785 "SEC_CX_OVT_SHDN_CX0-I",
786 "SEC_CX_OVT_SHDN_CX1-I",
787 "SEC_FNP_L_CX0-O",
788 "SEC_FNP_L_CX1-O",
789 "",
790 "SEC_MCU_GPIO-I",
791 "SEC_MCU_RST_N-O",
792 "SEC_MCU_RECOVERY_N-O";
793 };
794 };
795
796 imux34: i2c@2 {
797 #address-cells = <1>;
798 #size-cells = <0>;
799 reg = <2>;
800 };
801
802 imux35: i2c@3 {
803 #address-cells = <1>;
804 #size-cells = <0>;
805 reg = <3>;
806 };
807 };
808
809 i2c-mux@77 {
810 compatible = "nxp,pca9546";
811 #address-cells = <1>;
812 #size-cells = <0>;
813 reg = <0x77>;
814 i2c-mux-idle-disconnect;
815 vdd-supply = <&standby_power_regulator>;
816
817 imux36: i2c@0 {
818 #address-cells = <1>;
819 #size-cells = <0>;
820 reg = <0>;
821 };
822
823 imux37: i2c@1 {
824 #address-cells = <1>;
825 #size-cells = <0>;
826 reg = <1>;
827 };
828
829 imux38: i2c@2 {
830 #address-cells = <1>;
831 #size-cells = <0>;
832 reg = <2>;
833 };
834
835 imux39: i2c@3 {
836 #address-cells = <1>;
837 #size-cells = <0>;
838 reg = <3>;
839 };
840 };
841 };
842
843 // I2C7
844 // Module 0/1 Leak Sensors
845 // Module 0/1 Fan Controllers
846 &i2c6 {
847 status = "okay";
848 clock-frequency = <400000>;
849
850 pmic@12 {
851 compatible = "ti,lm5066i";
852 reg = <0x12>;
853 shunt-resistor-micro-ohms = <190>;
854 status = "okay";
855 };
856
857 pmic@14 {
858 compatible = "ti,lm5066i";
859 reg = <0x14>;
860 shunt-resistor-micro-ohms = <190>;
861 status = "okay";
862 };
863
864 pwm@20 {
865 compatible = "maxim,max31790";
866 reg = <0x20>;
867 };
868
869 pwm@23 {
870 compatible = "maxim,max31790";
871 reg = <0x23>;
872 };
873
874 pwm@2c {
875 compatible = "maxim,max31790";
876 reg = <0x2c>;
877 };
878
879 pwm@2f {
880 compatible = "maxim,max31790";
881 reg = <0x2f>;
882 };
883 };
884
885 // I2C9
886 // M.2
887 &i2c8 {
888 status = "okay";
889 clock-frequency = <400000>;
890 multi-master;
891 };
892
893 // I2C10
894 // HMC IO Expander
895 // Module 0/1 IO Expanders
896 &i2c9 {
897 status = "okay";
898 clock-frequency = <400000>;
899
900 // Module 0, Expander @0x20
901 exp0: gpio@20 {
902 compatible = "nxp,pca9555";
903 reg = <0x20>;
904 gpio-controller;
905 #gpio-cells = <2>;
906 interrupt-controller;
907 #interrupt-cells = <2>;
908 interrupt-parent = <&gpio1>;
909 interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
910 vcc-supply = <&standby_power_regulator>;
911 gpio-line-names =
912 "FPGA_THERM_OVERT_L-I",
913 "FPGA_READY_BMC-I",
914 "HMC_BMC_DETECT-O",
915 "HMC_PGOOD-O",
916 "",
917 "BMC_STBY_CYCLE-O",
918 "FPGA_EROT_FATAL_ERROR_L-I",
919 "WP_HW_EXT_CTRL_L-O",
920 "EROT_FPGA_RST_L-O",
921 "FPGA_EROT_RECOVERY_L-O",
922 "BMC_EROT_FPGA_SPI_MUX_SEL-O",
923 "USB_HUB_RESET_L-O",
924 "NCSI_CS1_SEL-O",
925 "SGPIO_EN_L-O",
926 "B2B_IOEXP_INT_L-I",
927 "I2C_BUS_MUX_RESET_L-O";
928 };
929
930 // Module 1, Expander @0x21
931 exp1: gpio@21 {
932 compatible = "nxp,pca9555";
933 reg = <0x21>;
934 gpio-controller;
935 #gpio-cells = <2>;
936 interrupt-controller;
937 #interrupt-cells = <2>;
938 interrupt-parent = <&gpio1>;
939 interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
940 vcc-supply = <&standby_power_regulator>;
941 gpio-line-names =
942 "SEC_FPGA_THERM_OVERT_L-I",
943 "SEC_FPGA_READY_BMC-I",
944 "",
945 "",
946 "",
947 "",
948 "SEC_FPGA_EROT_FATAL_ERROR_L-I",
949 "SEC_WP_HW_EXT_CTRL_L-O",
950 "SEC_EROT_FPGA_RST_L-O",
951 "SEC_FPGA_EROT_RECOVERY_L-O",
952 "SEC_BMC_EROT_FPGA_SPI_MUX_SEL-O",
953 "SEC_USB2_HUB_RST_L-O",
954 "",
955 "",
956 "",
957 "SEC_I2C_BUS_MUX_RESET_L-O";
958 };
959
960 // HMC Expander @0x27
961 exp2: gpio@27 {
962 compatible = "nxp,pca9555";
963 reg = <0x27>;
964 gpio-controller;
965 #gpio-cells = <2>;
966 interrupt-controller;
967 #interrupt-cells = <2>;
968 interrupt-parent = <&gpio1>;
969 interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
970 gpio-line-names =
971 "HMC_PRSNT_L-I",
972 "HMC_READY-I",
973 "HMC_EROT_FATAL_ERROR_L-I",
974 "I2C_MUX_SEL-O",
975 "HMC_EROT_SPI_MUX_SEL-O",
976 "HMC_EROT_RECOVERY_L-O",
977 "HMC_EROT_RST_L-O",
978 "GLOBAL_WP_HMC-O",
979 "FPGA_RST_L-O",
980 "USB2_HUB_RST-O",
981 "CPU_UART_MUX_SEL-O",
982 "",
983 "",
984 "",
985 "",
986 "";
987 };
988
989 // HMC Expander @0x74
990 exp3: gpio@74 {
991 compatible = "nxp,pca9555";
992 reg = <0x74>;
993 gpio-controller;
994 #gpio-cells = <2>;
995 interrupt-controller;
996 #interrupt-cells = <2>;
997 interrupt-parent = <&gpio1>;
998 interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
999 vcc-supply = <&standby_power_regulator>;
1000 gpio-line-names =
1001 "IOB_PRSNT_L",
1002 "IOB_DP_HPD",
1003 "IOX_BMC_RESET",
1004 "IOB_IOEXP_INT_L",
1005 "IOB_UID_LED_L",
1006 "IOB_UID_BTN_L",
1007 "IOB_SYS_RST_BTN_L",
1008 "IOB_PWR_LED_L",
1009 "IOB_PWR_BTN_L",
1010 "IOB_PHY_RST",
1011 "CPLD_JTAG_MUX_SEL",
1012 "",
1013 "",
1014 "",
1015 "",
1016 "";
1017 };
1018 };
1019
1020 // I2C11
1021 // BMC FRU EEPROM
1022 // BMC Temp Sensor
1023 &i2c10 {
1024 status = "okay";
1025 clock-frequency = <400000>;
1026
1027 // BMC FRU EEPROM - 256 bytes
1028 eeprom@50 {
1029 compatible = "atmel,24c02";
1030 reg = <0x50>;
1031 pagesize = <8>;
1032 };
1033 };
1034
1035 // I2C12
1036 &i2c11 {
1037 status = "disabled";
1038 };
1039
1040 // I2C13
1041 &i2c12 {
1042 status = "disabled";
1043 };
1044
1045 // I2C14
1046 // Module 0 UPHY3 SMBus
1047 &i2c13 {
1048 status = "disabled";
1049 };
1050
1051 // I2C15
1052 // Module 1 UPHY3 SMBus
1053 &i2c14 {
1054 status = "okay";
1055 clock-frequency = <100000>;
1056 multi-master;
1057
1058 //E1.S drive slot 0-3
1059 i2c-mux@77 {
1060 compatible = "nxp,pca9546";
1061 #address-cells = <1>;
1062 #size-cells = <0>;
1063 reg = <0x77>;
1064 i2c-mux-idle-disconnect;
1065 vdd-supply = <&standby_power_regulator>;
1066
1067 e1si2c0: i2c@0 {
1068 #address-cells = <1>;
1069 #size-cells = <0>;
1070 reg = <0>;
1071 };
1072
1073 e1si2c1: i2c@1 {
1074 #address-cells = <1>;
1075 #size-cells = <0>;
1076 reg = <1>;
1077 };
1078
1079 e1si2c2: i2c@2 {
1080 #address-cells = <1>;
1081 #size-cells = <0>;
1082 reg = <2>;
1083 };
1084
1085 e1si2c3: i2c@3 {
1086 #address-cells = <1>;
1087 #size-cells = <0>;
1088 reg = <3>;
1089 };
1090 };
1091 };
1092
1093 // I2C16
1094 &i2c15 {
1095 status = "okay";
1096 clock-frequency = <100000>;
1097 multi-master;
1098
1099 //E1.S drive slot 4-7
1100 i2c-mux@77 {
1101 compatible = "nxp,pca9546";
1102 #address-cells = <1>;
1103 #size-cells = <0>;
1104 reg = <0x77>;
1105 i2c-mux-idle-disconnect;
1106 vdd-supply = <&standby_power_regulator>;
1107
1108 e1si2c4: i2c@0 {
1109 #address-cells = <1>;
1110 #size-cells = <0>;
1111 reg = <0>;
1112 };
1113
1114 e1si2c5: i2c@1 {
1115 #address-cells = <1>;
1116 #size-cells = <0>;
1117 reg = <1>;
1118 };
1119
1120 e1si2c6: i2c@2 {
1121 #address-cells = <1>;
1122 #size-cells = <0>;
1123 reg = <2>;
1124 };
1125
1126 e1si2c7: i2c@3 {
1127 #address-cells = <1>;
1128 #size-cells = <0>;
1129 reg = <3>;
1130 };
1131 };
1132 };
1133
1134 &rng {
1135 status = "okay";
1136 };
1137
1138 &gpio0 {
1139 gpio-line-names =
1140 /*A0-A7*/ "", "", "", "", "", "", "", "",
1141 /*B0-B7*/ "", "", "", "", "", "", "", "",
1142 /*C0-C7*/ "SGPIO_I2C_MUX_SEL-O", "", "", "", "", "", "", "",
1143 /*D0-D7*/ "", "", "", "UART1_MUX_SEL-O", "", "FPGA_PEX_RST_L-O", "", "",
1144 /*E0-E7*/ "RTL8221_PHY_RST_L-O", "RTL8211_PHY_INT_L-I", "", "UART3_MUX_SEL-O",
1145 "", "", "", "SGPIO_BMC_EN-O",
1146 /*F0-F7*/ "", "", "", "", "", "", "", "",
1147 /*G0-G7*/ "", "", "", "", "", "", "", "",
1148 /*H0-H7*/ "", "", "", "", "", "", "", "",
1149 /*I0-I7*/ "", "", "", "", "", "QSPI2_RST_L-O", "GLOBAL_WP_BMC-O", "BMC_DDR4_TEN-O",
1150 /*J0-J7*/ "", "", "", "", "", "", "", "",
1151 /*K0-K7*/ "", "", "", "", "", "", "", "",
1152 /*L0-L7*/ "", "", "", "", "", "", "", "",
1153 /*M0-M7*/ "PCIE_EP_RST_EN-O", "BMC_FRU_WP-O", "FPGA_RST_L-O", "STBY_POWER_EN-O",
1154 "STBY_POWER_PG-I", "PCIE_EP_RST_L-O", "", "",
1155 /*N0-N7*/ "", "", "", "", "", "", "", "",
1156 /*O0-O7*/ "", "", "", "", "", "", "", "",
1157 /*P0-P7*/ "", "", "", "", "", "", "", "",
1158 /*Q0-Q7*/ "", "", "", "", "", "", "", "",
1159 /*R0-R7*/ "", "", "", "", "", "", "", "",
1160 /*S0-S7*/ "", "", "", "", "", "", "", "",
1161 /*T0-T7*/ "", "", "", "", "", "", "", "",
1162 /*U0-U7*/ "", "", "", "", "", "", "", "",
1163 /*V0-V7*/ "AP_EROT_REQ-O", "EROT_AP_GNT-I", "", "","PCB_TEMP_ALERT-I", "","", "",
1164 /*W0-W7*/ "", "", "", "", "", "", "", "",
1165 /*X0-X7*/ "", "", "TPM_MUX_SEL-O", "", "", "", "", "",
1166 /*Y0-Y7*/ "", "", "", "EMMC_RST-O", "","", "", "",
1167 /*Z0-Z7*/ "BMC_READY-O","", "", "", "", "", "", "";
1168 };
1169
1170 &gpio1 {
1171 /* 36 1.8V GPIOs */
1172 gpio-line-names =
1173 /*A0-A7*/ "", "", "", "", "", "", "", "",
1174 /*B0-B7*/ "", "", "", "", "", "", "IO_EXPANDER_INT_L-I","",
1175 /*C0-C7*/ "", "", "", "", "", "", "", "",
1176 /*D0-D7*/ "", "", "", "", "", "", "SPI_HOST_TPM_RST_L-O", "SPI_BMC_FPGA_INT_L-I",
1177 /*E0-E7*/ "", "", "", "", "", "", "", "";
1178 };