Debian Codegraph @

arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-balcones.dts

raw
1 // SPDX-License-Identifier: GPL-2.0-or-later
2 // Copyright 2025 IBM Corp.
3 /dts-v1/;
4
5 #include <dt-bindings/gpio/aspeed-gpio.h>
6 #include <dt-bindings/i2c/i2c.h>
7 #include <dt-bindings/leds/leds-pca955x.h>
8 #include "aspeed-g6.dtsi"
9 #include "ibm-power11-dual.dtsi"
10
11 / {
12 model = "Balcones";
13 compatible = "ibm,balcones-bmc", "aspeed,ast2600";
14
15 aliases {
16 serial4 = &uart5;
17 i2c16 = &i2c11mux0chn0;
18 i2c17 = &i2c11mux0chn1;
19 i2c18 = &i2c11mux0chn2;
20 i2c19 = &i2c11mux0chn3;
21 };
22
23 chosen {
24 stdout-path = &uart5;
25 };
26
27 gpio-keys-polled {
28 compatible = "gpio-keys-polled";
29 poll-interval = <1000>;
30
31 event-fan0-presence {
32 gpios = <&gpio0 ASPEED_GPIO(F, 4) GPIO_ACTIVE_LOW>;
33 label = "fan0-presence";
34 linux,code = <6>;
35 };
36
37 event-fan1-presence {
38 gpios = <&gpio0 ASPEED_GPIO(F, 5) GPIO_ACTIVE_LOW>;
39 label = "fan1-presence";
40 linux,code = <7>;
41 };
42 };
43
44 iio-hwmon {
45 compatible = "iio-hwmon";
46 io-channels = <&adc1 7>;
47 };
48
49 leds {
50 compatible = "gpio-leds";
51
52 led-fan0 {
53 gpios = <&gpio0 ASPEED_GPIO(G, 0) GPIO_ACTIVE_LOW>;
54 };
55
56 led-fan1 {
57 gpios = <&gpio0 ASPEED_GPIO(G, 1) GPIO_ACTIVE_LOW>;
58 };
59
60 led-rear-enc-id0 {
61 gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
62 };
63
64 led-rear-enc-fault0 {
65 gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
66 };
67 };
68
69 memory@80000000 {
70 device_type = "memory";
71 reg = <0x80000000 0x40000000>;
72 };
73
74 reserved-memory {
75 #address-cells = <1>;
76 #size-cells = <1>;
77 ranges;
78
79 event_log: region@b3d00000 {
80 reg = <0xb3d00000 0x100000>;
81 no-map;
82 };
83
84 ramoops@b3e00000 {
85 compatible = "ramoops";
86 reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
87 record-size = <0x8000>;
88 console-size = <0x8000>;
89 ftrace-size = <0x8000>;
90 pmsg-size = <0x8000>;
91 max-reason = <3>; /* KMSG_DUMP_EMERG */
92 };
93
94 /* LPC FW cycle bridge region requires natural alignment */
95 flash_memory: region@b4000000 {
96 reg = <0xb4000000 0x04000000>; /* 64M */
97 no-map;
98 };
99
100 /* VGA region is dictated by hardware strapping */
101 vga_memory: region@bf000000 {
102 compatible = "shared-dma-pool";
103 reg = <0xbf000000 0x01000000>; /* 16M */
104 no-map;
105 };
106 };
107 };
108
109 &adc1 {
110 aspeed,int-vref-microvolt = <2500000>;
111 pinctrl-names = "default";
112 pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
113 &pinctrl_adc10_default &pinctrl_adc11_default
114 &pinctrl_adc12_default &pinctrl_adc13_default
115 &pinctrl_adc14_default &pinctrl_adc15_default>;
116 status = "okay";
117 };
118
119 &ehci1 {
120 status = "okay";
121 };
122
123 &emmc {
124 clk-phase-mmc-hs200 = <180>, <180>;
125 status = "okay";
126 };
127
128 &emmc_controller {
129 status = "okay";
130 };
131
132 &gpio0 {
133 gpio-line-names =
134 /*A0-A7*/ "","","","","","","","",
135 /*B0-B7*/ "","","","","","","checkstop","",
136 /*C0-C7*/ "","","","","","","","",
137 /*D0-D7*/ "","","","","","","","",
138 /*E0-E7*/ "","","","","","","","",
139 /*F0-F7*/ "","fan-ctlr-reset","rtc-battery-voltage-read-enable",
140 "reset-cause-pinhole","","","","",
141 /*G0-G7*/ "fan0","fan1","","","","","","",
142 /*H0-H7*/ "","","rear-enc-id0","rear-enc-fault0","","","","",
143 /*I0-I7*/ "","","","","","","bmc-secure-boot","",
144 /*J0-J7*/ "","","","","","","","",
145 /*K0-K7*/ "","","","","","","","",
146 /*L0-L7*/ "","","","","","","","",
147 /*M0-M7*/ "","","","","","","","",
148 /*N0-N7*/ "","","","","","","","",
149 /*O0-O7*/ "","","","usb-power","","","","",
150 /*P0-P7*/ "","","","","","","","",
151 /*Q0-Q7*/ "cfam-reset","","regulator-standby-faulted","","","","","",
152 /*R0-R7*/ "bmc-tpm-reset","power-chassis-control","power-chassis-good","","",
153 "","","",
154 /*S0-S7*/ "presence-ps0","presence-ps1","","","power-ffs-sync-history","","",
155 "",
156 /*T0-T7*/ "","","","","","","","",
157 /*U0-U7*/ "","","","","","","","",
158 /*V0-V7*/ "","","","","","","","",
159 /*W0-W7*/ "","","","","","","","",
160 /*X0-X7*/ "","","","","","","","",
161 /*Y0-Y7*/ "","","","","","","","",
162 /*Z0-Z7*/ "","","","","","","","";
163
164 usb-power-hog {
165 gpio-hog;
166 gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
167 output-high;
168 };
169 };
170
171 &i2c0 {
172 status = "okay";
173
174 gpio@20 {
175 compatible = "ti,tca9554";
176 reg = <0x20>;
177 gpio-controller;
178 #gpio-cells = <2>;
179
180 gpio-line-names =
181 "",
182 "RUSSEL_FW_I2C_ENABLE_N",
183 "RUSSEL_OPPANEL_PRESENCE_N",
184 "BLYTH_OPPANEL_PRESENCE_N",
185 "CPU_TPM_CARD_PRESENT_N",
186 "",
187 "",
188 "DASD_BP_PRESENT_N";
189 };
190
191 eeprom@51 {
192 compatible = "atmel,24c64";
193 reg = <0x51>;
194 };
195 };
196
197 &i2c1 {
198 status = "okay";
199 };
200
201 &i2c2 {
202 status = "okay";
203
204 pmic@64 {
205 compatible = "ti,ucd90160";
206 reg = <0x64>;
207 };
208 };
209
210 &i2c3 {
211 status = "okay";
212
213 power-supply@5a {
214 compatible = "acbel,fsg032";
215 reg = <0x5a>;
216 };
217
218 power-supply@5b {
219 compatible = "acbel,fsg032";
220 reg = <0x5b>;
221 };
222 };
223
224 &i2c4 {
225 status = "okay";
226 };
227
228 &i2c5 {
229 status = "okay";
230
231 eeprom@52 {
232 compatible = "atmel,24c64";
233 reg = <0x52>;
234 };
235
236 led-controller@62 {
237 compatible = "nxp,pca9551";
238 reg = <0x62>;
239 #address-cells = <1>;
240 #size-cells = <0>;
241 gpio-controller;
242 #gpio-cells = <2>;
243
244 led@0 {
245 reg = <0>;
246 default-state = "keep";
247 label = "cablecard2-cxp-top";
248 retain-state-shutdown;
249 type = <PCA955X_TYPE_LED>;
250 };
251
252 led@1 {
253 reg = <1>;
254 default-state = "keep";
255 label = "cablecard2-cxp-bot";
256 retain-state-shutdown;
257 type = <PCA955X_TYPE_LED>;
258 };
259 };
260 };
261
262 &i2c6 {
263 status = "okay";
264 };
265
266 &i2c7 {
267 multi-master;
268 status = "okay";
269
270 temperature-sensor@48 {
271 compatible = "ti,tmp275";
272 reg = <0x48>;
273 };
274
275 eeprom@50 {
276 compatible = "atmel,24c64";
277 reg = <0x50>;
278 };
279
280 eeprom@51 {
281 compatible = "atmel,24c64";
282 reg = <0x51>;
283 };
284
285 pwm@53 {
286 compatible = "maxim,max31785a";
287 reg = <0x53>;
288 };
289
290 led-controller@60 {
291 compatible = "nxp,pca9551";
292 reg = <0x60>;
293 #address-cells = <1>;
294 #size-cells = <0>;
295 gpio-controller;
296 #gpio-cells = <2>;
297
298 led@0 {
299 reg = <0>;
300 default-state = "keep";
301 label = "front-sys-id0";
302 retain-state-shutdown;
303 type = <PCA955X_TYPE_LED>;
304 };
305
306 led@1 {
307 reg = <1>;
308 default-state = "keep";
309 label = "front-check-log0";
310 retain-state-shutdown;
311 type = <PCA955X_TYPE_LED>;
312 };
313
314 led@2 {
315 reg = <2>;
316 default-state = "keep";
317 label = "front-enc-fault1";
318 retain-state-shutdown;
319 type = <PCA955X_TYPE_LED>;
320 };
321
322 led@3 {
323 reg = <3>;
324 default-state = "keep";
325 label = "front-sys-pwron0";
326 retain-state-shutdown;
327 type = <PCA955X_TYPE_LED>;
328 };
329 };
330
331 lcd-controller@62 {
332 compatible = "ibm,op-panel";
333 reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
334 };
335
336 pressure-sensor@76 {
337 compatible = "infineon,dps310";
338 reg = <0x76>;
339 #io-channel-cells = <0>;
340 };
341 };
342
343 &i2c8 {
344 status = "okay";
345
346 rtc@32 {
347 compatible = "epson,rx8900";
348 reg = <0x32>;
349 };
350
351 eeprom@50 {
352 compatible = "atmel,24c128";
353 reg = <0x50>;
354 };
355
356 led-controller@60 {
357 compatible = "nxp,pca9551";
358 reg = <0x60>;
359 #address-cells = <1>;
360 #size-cells = <0>;
361 gpio-controller;
362 #gpio-cells = <2>;
363
364 gpio-line-names =
365 "",
366 "APSS_RESET_N",
367 "",
368 "N_MODE_CPU_N",
369 "",
370 "",
371 "P10_DCM_PRESENT",
372 "";
373 };
374
375 led-controller@61 {
376 compatible = "nxp,pca9552";
377 reg = <0x61>;
378 #address-cells = <1>;
379 #size-cells = <0>;
380 gpio-controller;
381 #gpio-cells = <2>;
382
383 gpio-line-names =
384 "",
385 "",
386 "SLOT2_PRSNT_EN_RSVD",
387 "",
388 "",
389 "",
390 "",
391 "SLOT2_EXPANDER_PRSNT_N",
392 "",
393 "",
394 "",
395 "",
396 "",
397 "",
398 "",
399 "";
400 };
401 };
402
403 &i2c9 {
404 status = "okay";
405
406 temperature-sensor@4c {
407 compatible = "ti,tmp423";
408 reg = <0x4c>;
409 };
410 };
411
412 &i2c10 {
413 status = "okay";
414 };
415
416 &i2c11 {
417 status = "okay";
418
419 gpio@20 {
420 compatible = "ti,tca9554";
421 reg = <0x20>;
422 gpio-controller;
423 #gpio-cells = <2>;
424
425 gpio-line-names =
426 "BOOT_RCVRY_TWI",
427 "BOOT_RCVRY_UART",
428 "",
429 "",
430 "",
431 "",
432 "",
433 "PE_SWITCH_RSTB_N";
434 };
435
436 temperature-sensor@4c {
437 compatible = "ti,tmp435";
438 reg = <0x4c>;
439 };
440
441 i2c-mux@75 {
442 compatible = "nxp,pca9849";
443 reg = <0x75>;
444 #address-cells = <1>;
445 #size-cells = <0>;
446 i2c-mux-idle-disconnect;
447
448 i2c11mux0chn0: i2c@0 {
449 reg = <0>;
450 #address-cells = <1>;
451 #size-cells = <0>;
452 };
453
454 i2c11mux0chn1: i2c@1 {
455 reg = <1>;
456 #address-cells = <1>;
457 #size-cells = <0>;
458 };
459
460 i2c11mux0chn2: i2c@2 {
461 reg = <2>;
462 #address-cells = <1>;
463 #size-cells = <0>;
464 };
465
466 i2c11mux0chn3: i2c@3 {
467 reg = <3>;
468 #address-cells = <1>;
469 #size-cells = <0>;
470 };
471 };
472 };
473
474 &i2c12 {
475 status = "okay";
476
477 tpm@2e {
478 compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
479 reg = <0x2e>;
480 memory-region = <&event_log>;
481 };
482
483 eeprom@50 {
484 compatible = "atmel,24c64";
485 reg = <0x50>;
486 };
487 };
488
489 &i2c13 {
490 status = "okay";
491
492 eeprom@50 {
493 compatible = "atmel,24c64";
494 reg = <0x50>;
495 };
496
497 led-controller@60 {
498 compatible = "nxp,pca9551";
499 reg = <0x60>;
500 #address-cells = <1>;
501 #size-cells = <0>;
502 gpio-controller;
503 #gpio-cells = <2>;
504
505 led@0 {
506 reg = <0>;
507 default-state = "keep";
508 label = "nvme3";
509 retain-state-shutdown;
510 type = <PCA955X_TYPE_LED>;
511 };
512
513 led@1 {
514 reg = <1>;
515 default-state = "keep";
516 label = "nvme2";
517 retain-state-shutdown;
518 type = <PCA955X_TYPE_LED>;
519 };
520
521 led@2 {
522 reg = <2>;
523 default-state = "keep";
524 label = "nvme1";
525 retain-state-shutdown;
526 type = <PCA955X_TYPE_LED>;
527 };
528
529 led@3 {
530 reg = <3>;
531 default-state = "keep";
532 label = "nvme0";
533 retain-state-shutdown;
534 type = <PCA955X_TYPE_LED>;
535 };
536 };
537 };
538
539 &i2c14 {
540 status = "okay";
541 };
542
543 &i2c15 {
544 status = "okay";
545 };
546
547 &ibt {
548 status = "okay";
549 };
550
551 &kcs2 {
552 aspeed,lpc-io-reg = <0xca8 0xcac>;
553 status = "okay";
554 };
555
556 &kcs3 {
557 aspeed,lpc-io-reg = <0xca2>;
558 aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
559 status = "okay";
560 };
561
562 &lpc_ctrl {
563 memory-region = <&flash_memory>;
564 status = "okay";
565 };
566
567 &mac2 {
568 clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
569 <&syscon ASPEED_CLK_MAC3RCLK>;
570 clock-names = "MACCLK", "RCLK";
571 pinctrl-names = "default";
572 pinctrl-0 = <&pinctrl_rmii3_default>;
573 use-ncsi;
574 status = "okay";
575 };
576
577 &pinctrl_emmc_default {
578 bias-disable;
579 };
580
581 &uart2 {
582 status = "okay";
583 };
584
585 &uhci {
586 status = "okay";
587 };
588
589 &vuart1 {
590 status = "okay";
591 };
592
593 &vuart2 {
594 status = "okay";
595 };
596
597 &wdt1 {
598 aspeed,reset-type = "none";
599 aspeed,external-signal;
600 aspeed,ext-push-pull;
601 aspeed,ext-active-high;
602
603 pinctrl-names = "default";
604 pinctrl-0 = <&pinctrl_wdtrst1_default>;
605 };
606
607 &wdt2 {
608 status = "okay";
609 };