| 1 |
The equipment |
| 2 |
============= |
| 3 |
|
| 4 |
ExpEYES Junior is interfaced and powered by the USB port of the computer, |
| 5 |
and it is programmable in Python. It can function as a low frequency |
| 6 |
oscilloscope, function generator, programmable voltage source, frequency |
| 7 |
counter and data logger. For connecting external signals, it has connectors |
| 8 |
on the top panel. as shown in the figure below. The software can monitor and |
| 9 |
control the voltages at these terminals. Inorder to measure other |
| 10 |
parameters (like temperature, pressure etc.), we |
| 11 |
need to convert them in to electrical signals by using appropriate |
| 12 |
sensor elements. Even though our primary objective is to |
| 13 |
do experiments, you are advised to read through the brief description of |
| 14 |
the equipment given below. The device can be also used as a test |
| 15 |
equipment for electrical and electronics engineering experiments. |
| 16 |
|
| 17 |
**IMPORTANT :** |
| 18 |
|
| 19 |
*The external voltages connected to ExpEYES Junior must be within the allowed |
| 20 |
limits. Inputs A1 and A2 must be within ±5 volts range and Inputs IN1 |
| 21 |
and IN2 must be in 0 to 5V range. Exceeding these limits may result in |
| 22 |
damage to the equipment. To measure higher voltages, scale them down |
| 23 |
using resistive potential divider networks.* |
| 24 |
|
| 25 |
.. image:: pics/ej-with-pc-lr.jpg |
| 26 |
:width: 400px |
| 27 |
|
| 28 |
|
| 29 |
External connections |
| 30 |
-------------------- |
| 31 |
|
| 32 |
The functions of the external connections briefly explained below. All |
| 33 |
the black coulored terminals are at ground potential, all other voltages |
| 34 |
are measured with respect to it. |
| 35 |
|
| 36 |
Input and Outputs: |
| 37 |
^^^^^^^^^^^^^^^^^^^ |
| 38 |
|
| 39 |
Constant Current Source (CCS) : |
| 40 |
""""""""""""""""""""""""""""""" |
| 41 |
|
| 42 |
The constant current source can be switched ON and OFF under software |
| 43 |
control. The nominal value is 1.1 mA but may vary from unit to unit, due |
| 44 |
to component tolerances. To measure the exact value, connect an ammeter |
| 45 |
from CCS to GND. Another method is to connect a known resistance (~1k) |
| 46 |
and measure the voltage drop across it. The load resistor should be less |
| 47 |
than 2k for this current source. |
| 48 |
|
| 49 |
Programmable Voltage (PVS) : |
| 50 |
"""""""""""""""""""""""""""" |
| 51 |
|
| 52 |
Can be set, from software, to any value in the 0 to +5V range. The |
| 53 |
resolution is 12 bits. |
| 54 |
|
| 55 |
Square Waves SQ1 and SQ2: |
| 56 |
""""""""""""""""""""""""""" |
| 57 |
|
| 58 |
Output swings from 0 to 5 volts and frequency can be varied 4Hz to |
| 59 |
100kHz. All intermediate values of frequency are not possible. Setting |
| 60 |
frequency to 0Hz will make the output HIGH and setting it to |
| 61 |
:math:`-1` will make it LOW, in both cases |
| 62 |
the wave generation is disabled. SQR1 output has a :math:`100~\Omega` **series |
| 63 |
resistor** inside so that it can drive LEDs directly. |
| 64 |
SQ2 is similar to SQ1 but it has no series resistor inside. |
| 65 |
|
| 66 |
Digital Output (OD1) : |
| 67 |
"""""""""""""""""""""" |
| 68 |
|
| 69 |
The voltage at OD1 can be set to 0 or 5 volts, using software. |
| 70 |
|
| 71 |
SINE, oscillator output: |
| 72 |
"""""""""""""""""""""""" |
| 73 |
|
| 74 |
Frequency is around 150Hz and amplitue around 4V. |
| 75 |
|
| 76 |
|
| 77 |
Capacitance meter IN1: |
| 78 |
"""""""""""""""""""""" |
| 79 |
|
| 80 |
Capacitance connected between IN1 and Ground can be measured. It works |
| 81 |
better for lower capacitance values, upto 10 nanoFarads, results may not |
| 82 |
be very accurate beyond that. |
| 83 |
|
| 84 |
Frequency Counter IN2: |
| 85 |
"""""""""""""""""""""" |
| 86 |
|
| 87 |
Capable of measuring frequencies upto several MHz. |
| 88 |
|
| 89 |
Resistive Sensor Input (SEN): |
| 90 |
""""""""""""""""""""""""""""" |
| 91 |
|
| 92 |
This is mainly meant for sensors like Light Dependent Resistor, |
| 93 |
Thermistor, Photo-transistor etc. SEN is internally connected to 5 |
| 94 |
volts through a 5.1\ k\ Ω resistor. |
| 95 |
|
| 96 |
:math:`\pm5\ V` Analog Inputs, A1 & A2: |
| 97 |
"""""""""""""""""""""""""""""""""""""""" |
| 98 |
|
| 99 |
Can measure voltage within the ±5 volts range. The maximum sampling rate is |
| 100 |
250 ksps total. |
| 101 |
|
| 102 |
:math:`0 to 5V` Analog Inputs, IN1 & IN2: |
| 103 |
"""""""""""""""""""""""""""""""""""""""""" |
| 104 |
|
| 105 |
Can measure voltage within the 0 to 5 volts range. |
| 106 |
|
| 107 |
Microphone output MIC: |
| 108 |
""""""""""""""""""""""" |
| 109 |
|
| 110 |
A condenser microphone is fixed on the unit and it's amplified output is available |
| 111 |
on MIC. |
| 112 |
|
| 113 |
1.2.2 Accessory Set |
| 114 |
------------------- |
| 115 |
|
| 116 |
.. image:: pics/accessory.jpg |
| 117 |
:width: 400px |
| 118 |
|
| 119 |
To get started, a set of accessories are provided with expEYES. |
| 120 |
|
| 121 |
- Pieces of wires, with pin and with crocodile clip. |
| 122 |
- Condenser microphone with leads. |
| 123 |
- Inductor Coil (2) : 44SWG wire on 1cm dia bobbin. Around 3000 Turns |
| 124 |
(some may have more turns). These coils can be used for studying |
| 125 |
inductance, electromagnetic induction etc. |
| 126 |
- Piezo Electric Discs (2) : Resonant frequency is around 3500 Hz. Can |
| 127 |
be energized by WG output or SQR1. Discs are enclosed in a plastic |
| 128 |
shell that forms a cavity, that enhances the amplitude of sound |
| 129 |
produced. |
| 130 |
- DC Motor : Should be powered by a DC voltage less than 3 volts. |
| 131 |
- Permanent Magnets : (a) 10mm dia & length (b) 5 mm dia & 10 mm length (c) |
| 132 |
Button size magnets(2) |
| 133 |
- 5mm LEDS : RED, BLUE, GREEN, WHITE |
| 134 |
- Capacitors : 100pF, 0.1uF , 1 uF & 22uF |
| 135 |
- Inductor : 10 mH / 20Ω, |
| 136 |
- Resistors : 560Ω, 1k\ Ω, 2.2k\ Ω , 10k\ Ω , 51k\ Ω and 100 k\ Ω |
| 137 |
- LDR |
| 138 |
- Two silicon diodes (1N4148) and one 3.3 volts zener diode |
| 139 |
- NPN Transistor( 2N2222) |
| 140 |
|