| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| 2 |
/* |
| 3 |
* Driver for the onsemi 10BASE-T1S NCN26000 PHYs family. |
| 4 |
* |
| 5 |
* Copyright 2022 onsemi |
| 6 |
*/ |
| 7 |
#include <linux/kernel.h> |
| 8 |
#include <linux/bitfield.h> |
| 9 |
#include <linux/errno.h> |
| 10 |
#include <linux/init.h> |
| 11 |
#include <linux/module.h> |
| 12 |
#include <linux/mii.h> |
| 13 |
#include <linux/phy.h> |
| 14 |
|
| 15 |
#include "mdio-open-alliance.h" |
| 16 |
|
| 17 |
#define PHY_ID_NCN26000 0x180FF5A1 |
| 18 |
|
| 19 |
#define NCN26000_REG_IRQ_CTL 16 |
| 20 |
#define NCN26000_REG_IRQ_STATUS 17 |
| 21 |
|
| 22 |
// the NCN26000 maps link_ctrl to BMCR_ANENABLE |
| 23 |
#define NCN26000_BCMR_LINK_CTRL_BIT BMCR_ANENABLE |
| 24 |
|
| 25 |
// the NCN26000 maps link_status to BMSR_ANEGCOMPLETE |
| 26 |
#define NCN26000_BMSR_LINK_STATUS_BIT BMSR_ANEGCOMPLETE |
| 27 |
|
| 28 |
#define NCN26000_IRQ_LINKST_BIT BIT(0) |
| 29 |
#define NCN26000_IRQ_PLCAST_BIT BIT(1) |
| 30 |
#define NCN26000_IRQ_LJABBER_BIT BIT(2) |
| 31 |
#define NCN26000_IRQ_RJABBER_BIT BIT(3) |
| 32 |
#define NCN26000_IRQ_PLCAREC_BIT BIT(4) |
| 33 |
#define NCN26000_IRQ_PHYSCOL_BIT BIT(5) |
| 34 |
#define NCN26000_IRQ_RESET_BIT BIT(15) |
| 35 |
|
| 36 |
#define TO_TMR_DEFAULT 32 |
| 37 |
|
| 38 |
static int ncn26000_config_init(struct phy_device *phydev) |
| 39 |
{ |
| 40 |
/* HW bug workaround: the default value of the PLCA TO_TIMER should be |
| 41 |
* 32, where the current version of NCN26000 reports 24. This will be |
| 42 |
* fixed in future PHY versions. For the time being, we force the |
| 43 |
* correct default here. |
| 44 |
*/ |
| 45 |
return phy_write_mmd(phydev, MDIO_MMD_VEND2, MDIO_OATC14_PLCA_TOTMR, |
| 46 |
TO_TMR_DEFAULT); |
| 47 |
} |
| 48 |
|
| 49 |
static int ncn26000_config_aneg(struct phy_device *phydev) |
| 50 |
{ |
| 51 |
/* Note: the NCN26000 supports only P2MP link mode. Therefore, AN is not |
| 52 |
* supported. However, this function is invoked by phylib to enable the |
| 53 |
* PHY, regardless of the AN support. |
| 54 |
*/ |
| 55 |
phydev->mdix_ctrl = ETH_TP_MDI_AUTO; |
| 56 |
phydev->mdix = ETH_TP_MDI; |
| 57 |
|
| 58 |
// bring up the link |
| 59 |
return phy_write(phydev, MII_BMCR, NCN26000_BCMR_LINK_CTRL_BIT); |
| 60 |
} |
| 61 |
|
| 62 |
static int ncn26000_read_status(struct phy_device *phydev) |
| 63 |
{ |
| 64 |
/* The NCN26000 reports NCN26000_LINK_STATUS_BIT if the link status of |
| 65 |
* the PHY is up. It further reports the logical AND of the link status |
| 66 |
* and the PLCA status in the BMSR_LSTATUS bit. |
| 67 |
*/ |
| 68 |
int ret; |
| 69 |
|
| 70 |
/* The link state is latched low so that momentary link |
| 71 |
* drops can be detected. Do not double-read the status |
| 72 |
* in polling mode to detect such short link drops except |
| 73 |
* the link was already down. |
| 74 |
*/ |
| 75 |
if (!phy_polling_mode(phydev) || !phydev->link) { |
| 76 |
ret = phy_read(phydev, MII_BMSR); |
| 77 |
if (ret < 0) |
| 78 |
return ret; |
| 79 |
else if (ret & NCN26000_BMSR_LINK_STATUS_BIT) |
| 80 |
goto upd_link; |
| 81 |
} |
| 82 |
|
| 83 |
ret = phy_read(phydev, MII_BMSR); |
| 84 |
if (ret < 0) |
| 85 |
return ret; |
| 86 |
|
| 87 |
upd_link: |
| 88 |
// update link status |
| 89 |
if (ret & NCN26000_BMSR_LINK_STATUS_BIT) { |
| 90 |
phydev->link = 1; |
| 91 |
phydev->pause = 0; |
| 92 |
phydev->duplex = DUPLEX_HALF; |
| 93 |
phydev->speed = SPEED_10; |
| 94 |
} else { |
| 95 |
phydev->link = 0; |
| 96 |
phydev->duplex = DUPLEX_UNKNOWN; |
| 97 |
phydev->speed = SPEED_UNKNOWN; |
| 98 |
} |
| 99 |
|
| 100 |
return 0; |
| 101 |
} |
| 102 |
|
| 103 |
static irqreturn_t ncn26000_handle_interrupt(struct phy_device *phydev) |
| 104 |
{ |
| 105 |
int ret; |
| 106 |
|
| 107 |
// read and aknowledge the IRQ status register |
| 108 |
ret = phy_read(phydev, NCN26000_REG_IRQ_STATUS); |
| 109 |
|
| 110 |
// check only link status changes |
| 111 |
if (ret < 0 || (ret & NCN26000_REG_IRQ_STATUS) == 0) |
| 112 |
return IRQ_NONE; |
| 113 |
|
| 114 |
phy_trigger_machine(phydev); |
| 115 |
return IRQ_HANDLED; |
| 116 |
} |
| 117 |
|
| 118 |
static int ncn26000_config_intr(struct phy_device *phydev) |
| 119 |
{ |
| 120 |
int ret; |
| 121 |
u16 irqe; |
| 122 |
|
| 123 |
if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { |
| 124 |
// acknowledge IRQs |
| 125 |
ret = phy_read(phydev, NCN26000_REG_IRQ_STATUS); |
| 126 |
if (ret < 0) |
| 127 |
return ret; |
| 128 |
|
| 129 |
// get link status notifications |
| 130 |
irqe = NCN26000_IRQ_LINKST_BIT; |
| 131 |
} else { |
| 132 |
// disable all IRQs |
| 133 |
irqe = 0; |
| 134 |
} |
| 135 |
|
| 136 |
ret = phy_write(phydev, NCN26000_REG_IRQ_CTL, irqe); |
| 137 |
if (ret != 0) |
| 138 |
return ret; |
| 139 |
|
| 140 |
return 0; |
| 141 |
} |
| 142 |
|
| 143 |
static struct phy_driver ncn26000_driver[] = { |
| 144 |
{ |
| 145 |
PHY_ID_MATCH_MODEL(PHY_ID_NCN26000), |
| 146 |
.name = "NCN26000", |
| 147 |
.features = PHY_BASIC_T1S_P2MP_FEATURES, |
| 148 |
.config_init = ncn26000_config_init, |
| 149 |
.config_intr = ncn26000_config_intr, |
| 150 |
.config_aneg = ncn26000_config_aneg, |
| 151 |
.read_status = ncn26000_read_status, |
| 152 |
.handle_interrupt = ncn26000_handle_interrupt, |
| 153 |
.get_plca_cfg = genphy_c45_plca_get_cfg, |
| 154 |
.set_plca_cfg = genphy_c45_plca_set_cfg, |
| 155 |
.get_plca_status = genphy_c45_plca_get_status, |
| 156 |
.soft_reset = genphy_soft_reset, |
| 157 |
}, |
| 158 |
}; |
| 159 |
|
| 160 |
module_phy_driver(ncn26000_driver); |
| 161 |
|
| 162 |
static const struct mdio_device_id __maybe_unused ncn26000_tbl[] = { |
| 163 |
{ PHY_ID_MATCH_MODEL(PHY_ID_NCN26000) }, |
| 164 |
{ } |
| 165 |
}; |
| 166 |
|
| 167 |
MODULE_DEVICE_TABLE(mdio, ncn26000_tbl); |
| 168 |
|
| 169 |
MODULE_AUTHOR("Piergiorgio Beruto"); |
| 170 |
MODULE_DESCRIPTION("onsemi 10BASE-T1S PHY driver"); |
| 171 |
MODULE_LICENSE("Dual BSD/GPL"); |