| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
| 2 |
/* |
| 3 |
* Copyright 2021 |
| 4 |
* Lukasz Majewski, DENX Software Engineering, [email protected] |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
#include "imx28.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
aliases { |
| 12 |
spi2 = &ssp3; |
| 13 |
}; |
| 14 |
|
| 15 |
chosen { |
| 16 |
bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1"; |
| 17 |
}; |
| 18 |
|
| 19 |
memory@40000000 { |
| 20 |
reg = <0x40000000 0x08000000>; |
| 21 |
device_type = "memory"; |
| 22 |
}; |
| 23 |
|
| 24 |
reg_3v3: regulator-reg-3v3 { |
| 25 |
compatible = "regulator-fixed"; |
| 26 |
regulator-name = "3V3"; |
| 27 |
regulator-min-microvolt = <3300000>; |
| 28 |
regulator-max-microvolt = <3300000>; |
| 29 |
}; |
| 30 |
|
| 31 |
reg_usb_5v: regulator-reg-usb-5v { |
| 32 |
compatible = "regulator-fixed"; |
| 33 |
regulator-name = "usb_vbus"; |
| 34 |
regulator-min-microvolt = <5000000>; |
| 35 |
regulator-max-microvolt = <5000000>; |
| 36 |
}; |
| 37 |
|
| 38 |
reg_fec_3v3: regulator-reg-fec-3v3 { |
| 39 |
compatible = "regulator-fixed"; |
| 40 |
regulator-name = "fec-phy"; |
| 41 |
regulator-min-microvolt = <3300000>; |
| 42 |
regulator-max-microvolt = <3300000>; |
| 43 |
}; |
| 44 |
}; |
| 45 |
|
| 46 |
&duart { |
| 47 |
pinctrl-names = "default"; |
| 48 |
pinctrl-0 = <&duart_pins_a>; |
| 49 |
status = "okay"; |
| 50 |
}; |
| 51 |
|
| 52 |
&i2c0 { |
| 53 |
pinctrl-names = "default"; |
| 54 |
pinctrl-0 = <&i2c0_pins_a>; |
| 55 |
status = "okay"; |
| 56 |
}; |
| 57 |
|
| 58 |
&spi3_pins_a { |
| 59 |
fsl,pinmux-ids = < |
| 60 |
MX28_PAD_AUART2_RX__SSP3_D4 |
| 61 |
MX28_PAD_AUART2_TX__SSP3_D5 |
| 62 |
MX28_PAD_SSP3_SCK__SSP3_SCK |
| 63 |
MX28_PAD_SSP3_MOSI__SSP3_CMD |
| 64 |
MX28_PAD_SSP3_MISO__SSP3_D0 |
| 65 |
MX28_PAD_SSP3_SS0__SSP3_D3 |
| 66 |
MX28_PAD_AUART2_TX__GPIO_3_9 |
| 67 |
>; |
| 68 |
}; |
| 69 |
|
| 70 |
&ssp0 { |
| 71 |
compatible = "fsl,imx28-mmc"; |
| 72 |
pinctrl-names = "default"; |
| 73 |
pinctrl-0 = <&mmc0_8bit_pins_a>; |
| 74 |
bus-width = <8>; |
| 75 |
vmmc-supply = <®_3v3>; |
| 76 |
non-removable; |
| 77 |
status = "okay"; |
| 78 |
}; |
| 79 |
|
| 80 |
&ssp2 { |
| 81 |
compatible = "fsl,imx28-spi"; |
| 82 |
pinctrl-names = "default"; |
| 83 |
pinctrl-0 = <&spi2_pins_a>; |
| 84 |
status = "okay"; |
| 85 |
}; |
| 86 |
|
| 87 |
&ssp3 { |
| 88 |
compatible = "fsl,imx28-spi"; |
| 89 |
pinctrl-names = "default"; |
| 90 |
pinctrl-0 = <&spi3_pins_a>; |
| 91 |
status = "okay"; |
| 92 |
|
| 93 |
flash@0 { |
| 94 |
compatible = "jedec,spi-nor"; |
| 95 |
spi-max-frequency = <20000000>; |
| 96 |
reg = <0>; |
| 97 |
|
| 98 |
partitions { |
| 99 |
compatible = "fixed-partitions"; |
| 100 |
#address-cells = <1>; |
| 101 |
#size-cells = <1>; |
| 102 |
|
| 103 |
partition@0 { |
| 104 |
label = "u-boot"; |
| 105 |
reg = <0 0x80000>; |
| 106 |
read-only; |
| 107 |
}; |
| 108 |
|
| 109 |
partition@80000 { |
| 110 |
label = "env0"; |
| 111 |
reg = <0x80000 0x10000>; |
| 112 |
}; |
| 113 |
|
| 114 |
partition@90000 { |
| 115 |
label = "env1"; |
| 116 |
reg = <0x90000 0x10000>; |
| 117 |
}; |
| 118 |
|
| 119 |
partition@a0000 { |
| 120 |
label = "rescue"; |
| 121 |
reg = <0xa0000 0xf40000>; |
| 122 |
}; |
| 123 |
|
| 124 |
partition@fe0000 { |
| 125 |
/* 1st sector for SPL boot img source data */ |
| 126 |
label = "spl-boot-data1"; |
| 127 |
reg = <0xfe0000 0x10000>; |
| 128 |
}; |
| 129 |
|
| 130 |
partition@ff0000 { |
| 131 |
/* 2nd sector for SPL boot img source data */ |
| 132 |
label = "spl-boot-data2"; |
| 133 |
reg = <0xff0000 0x10000>; |
| 134 |
}; |
| 135 |
}; |
| 136 |
}; |
| 137 |
}; |
| 138 |
|
| 139 |
&usb0 { |
| 140 |
vbus-supply = <®_usb_5v>; |
| 141 |
pinctrl-names = "default"; |
| 142 |
pinctrl-0 = <&usb0_pins_b>, <&usb0_id_pins_a>; |
| 143 |
dr_mode = "host"; |
| 144 |
status = "okay"; |
| 145 |
}; |
| 146 |
|
| 147 |
&usbphy0 { |
| 148 |
status = "okay"; |
| 149 |
}; |
| 150 |
|
| 151 |
&usb1 { |
| 152 |
vbus-supply = <®_usb_5v>; |
| 153 |
pinctrl-names = "default"; |
| 154 |
pinctrl-0 = <&usb1_pins_b>; |
| 155 |
dr_mode = "host"; |
| 156 |
status = "okay"; |
| 157 |
}; |
| 158 |
|
| 159 |
&usbphy1 { |
| 160 |
status = "okay"; |
| 161 |
}; |