| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Copyright (C) 2025 Amarula Solutions, Dario Binacchi <[email protected]> |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include "imx28.dtsi" |
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
compatible = "amarula,imx28-rmm", "fsl,imx28"; |
| 14 |
model = "Amarula i.MX28 rmm"; |
| 15 |
|
| 16 |
memory@40000000 { |
| 17 |
reg = <0x40000000 0x08000000>; |
| 18 |
device_type = "memory"; |
| 19 |
}; |
| 20 |
|
| 21 |
backlight { |
| 22 |
compatible = "pwm-backlight"; |
| 23 |
pwms = <&pwm 4 5000000 0>; |
| 24 |
brightness-levels = <0 255>; |
| 25 |
num-interpolated-steps = <255>; |
| 26 |
default-brightness-level = <255>; |
| 27 |
power-supply = <®_5v>; |
| 28 |
}; |
| 29 |
|
| 30 |
beeper { |
| 31 |
compatible = "pwm-beeper"; |
| 32 |
pwms = <&pwm 7 100000 0>; |
| 33 |
}; |
| 34 |
|
| 35 |
leds { |
| 36 |
compatible = "gpio-leds"; |
| 37 |
pinctrl-names = "default"; |
| 38 |
pinctrl-0 = <&leds_pins>; |
| 39 |
|
| 40 |
led-0 { |
| 41 |
gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>; |
| 42 |
default-state = "off"; |
| 43 |
}; |
| 44 |
|
| 45 |
led-1 { |
| 46 |
gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; |
| 47 |
default-state = "off"; |
| 48 |
}; |
| 49 |
|
| 50 |
led-2 { |
| 51 |
gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>; |
| 52 |
default-state = "off"; |
| 53 |
}; |
| 54 |
}; |
| 55 |
|
| 56 |
reg_1v8: regulator-1v8 { |
| 57 |
compatible = "regulator-fixed"; |
| 58 |
regulator-name = "1v8"; |
| 59 |
regulator-min-microvolt = <1800000>; |
| 60 |
regulator-max-microvolt = <1800000>; |
| 61 |
}; |
| 62 |
|
| 63 |
reg_3v3: regulator-3v3 { |
| 64 |
compatible = "regulator-fixed"; |
| 65 |
regulator-name = "3v3"; |
| 66 |
regulator-min-microvolt = <3300000>; |
| 67 |
regulator-max-microvolt = <3300000>; |
| 68 |
regulator-always-on; |
| 69 |
}; |
| 70 |
|
| 71 |
reg_5v: regulator-5v { |
| 72 |
compatible = "regulator-fixed"; |
| 73 |
regulator-name = "5v"; |
| 74 |
regulator-min-microvolt = <5000000>; |
| 75 |
regulator-max-microvolt = <5000000>; |
| 76 |
regulator-always-on; |
| 77 |
}; |
| 78 |
|
| 79 |
reg_fec_3v3: regulator-fec-3v3 { |
| 80 |
compatible = "regulator-fixed"; |
| 81 |
pinctrl-names = "default"; |
| 82 |
pinctrl-0 = <&fec_3v3_enable_pin>; |
| 83 |
regulator-name = "fec-3v3"; |
| 84 |
regulator-min-microvolt = <3300000>; |
| 85 |
regulator-max-microvolt = <3300000>; |
| 86 |
gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; |
| 87 |
enable-active-high; |
| 88 |
startup-delay-us = <300000>; |
| 89 |
vin-supply = <®_5v>; |
| 90 |
}; |
| 91 |
|
| 92 |
reg_usb0_vbus: regulator-usb0-vbus { |
| 93 |
compatible = "regulator-fixed"; |
| 94 |
pinctrl-names = "default"; |
| 95 |
pinctrl-0 = <&usb0_vbus_enable_pin>; |
| 96 |
regulator-name = "usb0_vbus"; |
| 97 |
regulator-min-microvolt = <5000000>; |
| 98 |
regulator-max-microvolt = <5000000>; |
| 99 |
gpio = <&gpio2 5 GPIO_ACTIVE_HIGH>; |
| 100 |
enable-active-high; |
| 101 |
regulator-always-on; |
| 102 |
}; |
| 103 |
|
| 104 |
reg_usb1_vbus: regulator-usb1-vbus { |
| 105 |
compatible = "regulator-fixed"; |
| 106 |
pinctrl-names = "default"; |
| 107 |
pinctrl-0 = <&usb1_vbus_enable_pin>; |
| 108 |
regulator-name = "usb1_vbus"; |
| 109 |
regulator-min-microvolt = <5000000>; |
| 110 |
regulator-max-microvolt = <5000000>; |
| 111 |
gpio = <&gpio2 6 GPIO_ACTIVE_HIGH>; |
| 112 |
enable-active-high; |
| 113 |
regulator-always-on; |
| 114 |
}; |
| 115 |
|
| 116 |
sound { |
| 117 |
compatible = "simple-audio-card"; |
| 118 |
simple-audio-card,name = "imx28-mrmmi-tlv320aic3x-audio"; |
| 119 |
simple-audio-card,format = "i2s"; |
| 120 |
simple-audio-card,bitclock-master = <&cpu_dai>; |
| 121 |
simple-audio-card,frame-master = <&cpu_dai>; |
| 122 |
simple-audio-card,widgets = |
| 123 |
"Headphone", "Headphone Jack"; |
| 124 |
simple-audio-card,routing = |
| 125 |
"Headphone Jack", "HPROUT", |
| 126 |
"Headphone Jack", "HPRCOM"; |
| 127 |
simple-audio-card,mclk-fs = <512>; |
| 128 |
|
| 129 |
cpu_dai: simple-audio-card,cpu { |
| 130 |
sound-dai = <&saif0>; |
| 131 |
clocks = <&saif0>; |
| 132 |
}; |
| 133 |
|
| 134 |
codec_dai: simple-audio-card,codec { |
| 135 |
sound-dai = <&tlv320aic3x>; |
| 136 |
}; |
| 137 |
}; |
| 138 |
}; |
| 139 |
|
| 140 |
&auart0 { |
| 141 |
pinctrl-names = "default"; |
| 142 |
pinctrl-0 = <&auart0_2pins_a>; |
| 143 |
status = "okay"; |
| 144 |
}; |
| 145 |
|
| 146 |
&auart1 { |
| 147 |
pinctrl-names = "default"; |
| 148 |
pinctrl-0 = <&auart1_pins_a>; |
| 149 |
status = "okay"; |
| 150 |
}; |
| 151 |
|
| 152 |
&can0 { |
| 153 |
pinctrl-names = "default"; |
| 154 |
pinctrl-0 = <&can0_pins_a>; |
| 155 |
status = "okay"; |
| 156 |
}; |
| 157 |
|
| 158 |
&duart { |
| 159 |
pinctrl-names = "default"; |
| 160 |
pinctrl-0 = <&duart_pins_b>; |
| 161 |
status = "okay"; |
| 162 |
}; |
| 163 |
|
| 164 |
&duart_pins_b { |
| 165 |
fsl,voltage = <MXS_VOLTAGE_LOW>; |
| 166 |
}; |
| 167 |
|
| 168 |
&gpmi { |
| 169 |
#size-cells = <0>; |
| 170 |
pinctrl-names = "default"; |
| 171 |
pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>; |
| 172 |
status = "okay"; |
| 173 |
}; |
| 174 |
|
| 175 |
&i2c0 { |
| 176 |
pinctrl-names = "default"; |
| 177 |
pinctrl-0 = <&i2c0_pins_a>; |
| 178 |
status = "okay"; |
| 179 |
|
| 180 |
tlv320aic3x: audio-codec@18 { |
| 181 |
compatible = "ti,tlv320aic3x"; |
| 182 |
pinctrl-names = "default"; |
| 183 |
pinctrl-0 = <&tlv320aic3x_pins>; |
| 184 |
reg = <0x18>; |
| 185 |
reset-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; |
| 186 |
#sound-dai-cells = <0>; |
| 187 |
DVDD-supply = <®_1v8>; |
| 188 |
IOVDD-supply = <®_3v3>; |
| 189 |
AVDD-supply = <®_3v3>; |
| 190 |
DRVDD-supply = <®_3v3>; |
| 191 |
}; |
| 192 |
|
| 193 |
touchscreen: touchscreen@38 { |
| 194 |
compatible = "edt,edt-ft5306"; |
| 195 |
reg = <0x38>; |
| 196 |
pinctrl-names = "default"; |
| 197 |
pinctrl-0 = <&edt_ft5x06_pins &edt_ft5x06_wake_pin>; |
| 198 |
interrupt-parent = <&gpio0>; |
| 199 |
interrupts = <19 IRQ_TYPE_EDGE_RISING>; |
| 200 |
reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; |
| 201 |
wake-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; |
| 202 |
}; |
| 203 |
}; |
| 204 |
|
| 205 |
&lradc { |
| 206 |
status = "okay"; |
| 207 |
}; |
| 208 |
|
| 209 |
&mac0 { |
| 210 |
pinctrl-names = "default"; |
| 211 |
pinctrl-0 = <&mac0_pins_a>; |
| 212 |
phy-mode = "rmii"; |
| 213 |
phy-supply = <®_fec_3v3>; |
| 214 |
phy-handle = <ðphy>; |
| 215 |
status = "okay"; |
| 216 |
|
| 217 |
mdio { |
| 218 |
#address-cells = <1>; |
| 219 |
#size-cells = <0>; |
| 220 |
|
| 221 |
ethphy: ethernet-phy@0 { |
| 222 |
compatible = "ethernet-phy-ieee802.3-c22"; |
| 223 |
reg = <0>; |
| 224 |
max-speed = <100>; |
| 225 |
reset-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>; |
| 226 |
reset-assert-us = <4000>; |
| 227 |
reset-deassert-us = <4000>; |
| 228 |
}; |
| 229 |
}; |
| 230 |
}; |
| 231 |
|
| 232 |
&pinctrl { |
| 233 |
pinctrl-names = "default"; |
| 234 |
pinctrl-0 = <&hog_pins_a>; |
| 235 |
|
| 236 |
edt_ft5x06_pins: edt-ft5x06@0 { |
| 237 |
reg = <0>; |
| 238 |
fsl,pinmux-ids = < |
| 239 |
MX28_PAD_GPMI_RDY1__GPIO_0_21 /* Reset */ |
| 240 |
MX28_PAD_GPMI_CE3N__GPIO_0_19 /* Interrupt */ |
| 241 |
>; |
| 242 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 243 |
fsl,pull-up = <MXS_PULL_ENABLE>; |
| 244 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 245 |
}; |
| 246 |
|
| 247 |
edt_ft5x06_wake_pin: edt-ft5x06-wake@0 { |
| 248 |
reg = <0>; |
| 249 |
fsl,pinmux-ids = <MX28_PAD_GPMI_CE2N__GPIO_0_18>; |
| 250 |
fsl,drive-strength = <MXS_DRIVE_16mA>; |
| 251 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 252 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 253 |
}; |
| 254 |
|
| 255 |
fec_3v3_enable_pin: fec-3v3-enable@0 { |
| 256 |
reg = <0>; |
| 257 |
fsl,pinmux-ids = <MX28_PAD_SPDIF__GPIO_3_27>; |
| 258 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 259 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 260 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 261 |
}; |
| 262 |
|
| 263 |
hog_pins_a: hog@0 { |
| 264 |
reg = <0>; |
| 265 |
fsl,pinmux-ids = < |
| 266 |
MX28_PAD_SSP2_SS1__GPIO_2_20 /* External power */ |
| 267 |
>; |
| 268 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 269 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 270 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 271 |
}; |
| 272 |
|
| 273 |
leds_pins: leds@0 { |
| 274 |
reg = <0>; |
| 275 |
fsl,pinmux-ids = < |
| 276 |
MX28_PAD_SSP0_DATA7__GPIO_2_7 |
| 277 |
MX28_PAD_PWM0__GPIO_3_16 |
| 278 |
MX28_PAD_PWM1__GPIO_3_17 |
| 279 |
>; |
| 280 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 281 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 282 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 283 |
}; |
| 284 |
|
| 285 |
tlv320aic3x_pins: tlv320aic3x-pins@0 { |
| 286 |
reg = <0>; |
| 287 |
fsl,pinmux-ids = <MX28_PAD_SSP0_DATA4__GPIO_2_4>; |
| 288 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 289 |
fsl,pull-up = <MXS_PULL_ENABLE>; |
| 290 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 291 |
}; |
| 292 |
|
| 293 |
usb0_vbus_enable_pin: usb0-vbus-enable@0 { |
| 294 |
reg = <0>; |
| 295 |
fsl,pinmux-ids = <MX28_PAD_SSP0_DATA5__GPIO_2_5>; |
| 296 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 297 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 298 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 299 |
}; |
| 300 |
|
| 301 |
usb1_vbus_enable_pin: usb1-vbus-enable@0 { |
| 302 |
reg = <0>; |
| 303 |
fsl,pinmux-ids = <MX28_PAD_SSP0_DATA6__GPIO_2_6>; |
| 304 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 305 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 306 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 307 |
}; |
| 308 |
}; |
| 309 |
|
| 310 |
&pwm { |
| 311 |
pinctrl-names = "default"; |
| 312 |
pinctrl-0 = <&pwm4_pins_a &pwm7_pins_a>; |
| 313 |
status = "okay"; |
| 314 |
}; |
| 315 |
|
| 316 |
&saif0 { |
| 317 |
pinctrl-names = "default"; |
| 318 |
pinctrl-0 = <&saif0_pins_a>; |
| 319 |
status = "okay"; |
| 320 |
}; |
| 321 |
|
| 322 |
/* microSD */ |
| 323 |
&ssp0 { |
| 324 |
compatible = "fsl,imx28-mmc"; |
| 325 |
pinctrl-names = "default"; |
| 326 |
pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>; |
| 327 |
broken-cd; |
| 328 |
bus-width = <4>; |
| 329 |
status = "okay"; |
| 330 |
}; |
| 331 |
|
| 332 |
&usb0 { |
| 333 |
dr_mode = "host"; |
| 334 |
vbus-supply = <®_usb0_vbus>; |
| 335 |
status = "okay"; |
| 336 |
}; |
| 337 |
|
| 338 |
&usb1 { |
| 339 |
dr_mode = "host"; |
| 340 |
vbus-supply = <®_usb1_vbus>; |
| 341 |
status = "okay"; |
| 342 |
}; |
| 343 |
|
| 344 |
&usbphy0 { |
| 345 |
status = "okay"; |
| 346 |
}; |
| 347 |
|
| 348 |
&usbphy1 { |
| 349 |
status = "okay"; |
| 350 |
}; |