| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* Copyright (C) 2013-2014,2016 Michael Heimpold <[email protected]> |
| 4 |
* Copyright (C) 2015-2017 I2SE GmbH <[email protected]> |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
#include "imx28.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "I2SE Duckbill"; |
| 13 |
compatible = "i2se,duckbill", "fsl,imx28"; |
| 14 |
|
| 15 |
memory@40000000 { |
| 16 |
device_type = "memory"; |
| 17 |
reg = <0x40000000 0x08000000>; |
| 18 |
}; |
| 19 |
|
| 20 |
reg_3p3v: regulator-3p3v { |
| 21 |
compatible = "regulator-fixed"; |
| 22 |
regulator-name = "3P3V"; |
| 23 |
regulator-min-microvolt = <3300000>; |
| 24 |
regulator-max-microvolt = <3300000>; |
| 25 |
regulator-always-on; |
| 26 |
}; |
| 27 |
|
| 28 |
leds { |
| 29 |
compatible = "gpio-leds"; |
| 30 |
pinctrl-names = "default"; |
| 31 |
pinctrl-0 = <&led_pins>; |
| 32 |
|
| 33 |
status-red { |
| 34 |
label = "duckbill:red:status"; |
| 35 |
gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; |
| 36 |
linux,default-trigger = "default-on"; |
| 37 |
}; |
| 38 |
|
| 39 |
status-green { |
| 40 |
label = "duckbill:green:status"; |
| 41 |
gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>; |
| 42 |
linux,default-trigger = "heartbeat"; |
| 43 |
}; |
| 44 |
}; |
| 45 |
}; |
| 46 |
|
| 47 |
&auart0 { |
| 48 |
pinctrl-names = "default"; |
| 49 |
pinctrl-0 = <&auart0_2pins_a>; |
| 50 |
status = "okay"; |
| 51 |
}; |
| 52 |
|
| 53 |
&duart { |
| 54 |
pinctrl-names = "default"; |
| 55 |
pinctrl-0 = <&duart_pins_a>; |
| 56 |
status = "okay"; |
| 57 |
}; |
| 58 |
|
| 59 |
&lradc { |
| 60 |
status = "okay"; |
| 61 |
}; |
| 62 |
|
| 63 |
&i2c0 { |
| 64 |
pinctrl-names = "default"; |
| 65 |
pinctrl-0 = <&i2c0_pins_a>; |
| 66 |
status = "okay"; |
| 67 |
}; |
| 68 |
|
| 69 |
&mac0 { |
| 70 |
phy-mode = "rmii"; |
| 71 |
pinctrl-names = "default"; |
| 72 |
pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>; |
| 73 |
phy-supply = <®_3p3v>; |
| 74 |
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>; |
| 75 |
phy-reset-duration = <25>; |
| 76 |
status = "okay"; |
| 77 |
}; |
| 78 |
|
| 79 |
&pinctrl { |
| 80 |
pinctrl-names = "default"; |
| 81 |
pinctrl-0 = <&hog_pins_a>; |
| 82 |
|
| 83 |
hog_pins_a: hog@0 { |
| 84 |
reg = <0>; |
| 85 |
fsl,pinmux-ids = < |
| 86 |
MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */ |
| 87 |
>; |
| 88 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 89 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 90 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 91 |
}; |
| 92 |
|
| 93 |
mac0_phy_reset_pin: mac0-phy-reset@0 { |
| 94 |
reg = <0>; |
| 95 |
fsl,pinmux-ids = < |
| 96 |
MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */ |
| 97 |
>; |
| 98 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 99 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 100 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 101 |
}; |
| 102 |
|
| 103 |
led_pins: leds@0 { |
| 104 |
reg = <0>; |
| 105 |
fsl,pinmux-ids = < |
| 106 |
MX28_PAD_AUART1_RX__GPIO_3_4 |
| 107 |
MX28_PAD_AUART1_TX__GPIO_3_5 |
| 108 |
>; |
| 109 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 110 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 111 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 112 |
}; |
| 113 |
}; |
| 114 |
|
| 115 |
&ssp0 { |
| 116 |
compatible = "fsl,imx28-mmc"; |
| 117 |
pinctrl-names = "default"; |
| 118 |
pinctrl-0 = <&mmc0_4bit_pins_a |
| 119 |
&mmc0_cd_cfg &mmc0_sck_cfg>; |
| 120 |
bus-width = <4>; |
| 121 |
vmmc-supply = <®_3p3v>; |
| 122 |
status = "okay"; |
| 123 |
}; |
| 124 |
|
| 125 |
&ssp2 { |
| 126 |
compatible = "fsl,imx28-spi"; |
| 127 |
pinctrl-names = "default"; |
| 128 |
pinctrl-0 = <&spi2_pins_a>; |
| 129 |
status = "okay"; |
| 130 |
}; |
| 131 |
|
| 132 |
&usb0 { |
| 133 |
dr_mode = "peripheral"; |
| 134 |
status = "okay"; |
| 135 |
}; |
| 136 |
|
| 137 |
&usbphy0 { |
| 138 |
status = "okay"; |
| 139 |
}; |