| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* Copyright 2012 Freescale Semiconductor, Inc. |
| 4 |
* |
| 5 |
* Author: Fabio Estevam <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
/dts-v1/; |
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include "imx23.dtsi" |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "i.MX23 Olinuxino Low Cost Board"; |
| 14 |
compatible = "olimex,imx23-olinuxino", "fsl,imx23"; |
| 15 |
|
| 16 |
memory@40000000 { |
| 17 |
device_type = "memory"; |
| 18 |
reg = <0x40000000 0x04000000>; |
| 19 |
}; |
| 20 |
|
| 21 |
apb@80000000 { |
| 22 |
apbh-bus@80000000 { |
| 23 |
ssp0: spi@80010000 { |
| 24 |
compatible = "fsl,imx23-mmc"; |
| 25 |
pinctrl-names = "default"; |
| 26 |
pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>; |
| 27 |
bus-width = <4>; |
| 28 |
broken-cd; |
| 29 |
status = "okay"; |
| 30 |
}; |
| 31 |
|
| 32 |
pinctrl@80018000 { |
| 33 |
pinctrl-names = "default"; |
| 34 |
pinctrl-0 = <&hog_pins_a>; |
| 35 |
|
| 36 |
hog_pins_a: hog@0 { |
| 37 |
reg = <0>; |
| 38 |
fsl,pinmux-ids = < |
| 39 |
MX23_PAD_GPMI_ALE__GPIO_0_17 |
| 40 |
>; |
| 41 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 42 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 43 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 44 |
}; |
| 45 |
|
| 46 |
led_pin_gpio2_1: led_gpio2_1@0 { |
| 47 |
reg = <0>; |
| 48 |
fsl,pinmux-ids = < |
| 49 |
MX23_PAD_SSP1_DETECT__GPIO_2_1 |
| 50 |
>; |
| 51 |
fsl,drive-strength = <MXS_DRIVE_4mA>; |
| 52 |
fsl,voltage = <MXS_VOLTAGE_HIGH>; |
| 53 |
fsl,pull-up = <MXS_PULL_DISABLE>; |
| 54 |
}; |
| 55 |
}; |
| 56 |
|
| 57 |
ssp1: spi@80034000 { |
| 58 |
#address-cells = <1>; |
| 59 |
#size-cells = <0>; |
| 60 |
compatible = "fsl,imx23-spi"; |
| 61 |
pinctrl-names = "default"; |
| 62 |
pinctrl-0 = <&spi2_pins_a>; |
| 63 |
status = "okay"; |
| 64 |
}; |
| 65 |
}; |
| 66 |
|
| 67 |
apbx-bus@80040000 { |
| 68 |
lradc@80050000 { |
| 69 |
status = "okay"; |
| 70 |
}; |
| 71 |
|
| 72 |
i2c: i2c@80058000 { |
| 73 |
pinctrl-names = "default"; |
| 74 |
pinctrl-0 = <&i2c_pins_b>; |
| 75 |
status = "okay"; |
| 76 |
}; |
| 77 |
|
| 78 |
duart: serial@80070000 { |
| 79 |
pinctrl-names = "default"; |
| 80 |
pinctrl-0 = <&duart_pins_a>; |
| 81 |
status = "okay"; |
| 82 |
}; |
| 83 |
|
| 84 |
auart0: serial@8006c000 { |
| 85 |
pinctrl-names = "default"; |
| 86 |
pinctrl-0 = <&auart0_2pins_a>; |
| 87 |
status = "okay"; |
| 88 |
}; |
| 89 |
|
| 90 |
usbphy0: usbphy@8007c000 { |
| 91 |
status = "okay"; |
| 92 |
}; |
| 93 |
}; |
| 94 |
}; |
| 95 |
|
| 96 |
ahb@80080000 { |
| 97 |
usb0: usb@80080000 { |
| 98 |
dr_mode = "host"; |
| 99 |
vbus-supply = <®_usb0_vbus>; |
| 100 |
status = "okay"; |
| 101 |
}; |
| 102 |
}; |
| 103 |
|
| 104 |
reg_usb0_vbus: regulator-0 { |
| 105 |
compatible = "regulator-fixed"; |
| 106 |
regulator-name = "usb0_vbus"; |
| 107 |
regulator-min-microvolt = <5000000>; |
| 108 |
regulator-max-microvolt = <5000000>; |
| 109 |
enable-active-high; |
| 110 |
startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */ |
| 111 |
gpio = <&gpio0 17 0>; |
| 112 |
}; |
| 113 |
|
| 114 |
leds { |
| 115 |
compatible = "gpio-leds"; |
| 116 |
pinctrl-names = "default"; |
| 117 |
pinctrl-0 = <&led_pin_gpio2_1>; |
| 118 |
|
| 119 |
user { |
| 120 |
label = "green"; |
| 121 |
gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; |
| 122 |
}; |
| 123 |
}; |
| 124 |
}; |