Debian Codegraph @

config/thermofloor/heatit-zdim.xml

raw
1 <?xml version="1.0" encoding="utf-8"?>
2 <Product Revision="2" xmlns="https://github.com/OpenZWave/open-zwave">
3 <MetaData>
4 <MetaDataItem name="OzwInfoPage">http://www.openzwave.com/device-database/019b:2200:0003</MetaDataItem>
5 <MetaDataItem name="ProductPic">images/thermofloor/heatit_zdim.png</MetaDataItem>
6 <MetaDataItem id="2200" name="ZWProductPage" type="0003">https://products.z-wavealliance.org/products/3261</MetaDataItem>
7 <MetaDataItem id="2200" name="Identifier" type="0003">Zdim</MetaDataItem>
8 <MetaDataItem name="ProductManual">https://products.z-wavealliance.org/ProductManual/File?folder=&amp;filename=product_documents/3261/Manual_Heatit_Z-DIM_FW%201.0_Ver2019-A_ENG.pdf</MetaDataItem>
9 <MetaDataItem name="Description">Z-Wave rotary dimmer for different light sources. The LED dimmer dims at low load without the light flickering. Dimmer LED from 1-200VA, 230V halogen and incandescent bulbs, dimmable LED drivers and electronic transformers. Not affected by additional starting currents. Need L + N conductor connected.
10 The dimmer has end-turn function. This allows you to turn on the light and dimming with one dimmer, and then turn off the light with another dimmer. Convenient for example in stairs and corridors.
11 The dimmer fits into standard Elko, Schneider Exxact and Gira System 55 frame systems.
12
13 FUNCTIONS
14 - Z-wave rotary dimmer
15 - Scene controller
16 - Dims:
17 - LED
18 - 230V halogen
19 - Incandescent lightbulbs
20 - Dimable LED-drivers
21 - Electronic transformators
22 - Starts at 1VA and dims up to 200VA LED
23 - Trailing edge
24 - Multiway switching option
25 - Electronic thermal cutoff with automatic reset
26 - Firmware updates (OTA)
27 - Power metering
28 - Supports encryption mode: S0, S2 Authenticated Class, S2 Unauthenticated Class
29
30 CONNECTION
31 1. Disconnect the power.
32 2. Connect the live to the dimmer terminal marked "L".
33 3. Connect the neutral to the dimmer terminal marked "N".
34 4. Connect the neutral to the load terminal marked "N".
35 5. Connect the load terminal marked "L" to the dimmer terminal marked (see wiring
36 diagram).
37 6. Install the dimmer (A) in the wall box. Make sure that no wires are pinched.
38 7. Attach the cover (B) with the supplied nut (C).
39 8. Attach the button (D) with a simple push.
40 To use the multiway function (stairway function) a 230VAC rated momentary switch
41 can be connected as follows:
42 9. Connect the live to the toggle switch terminal marked "L".
43 10. Connect the toggle switch terminal marked to the dimmer terminal marked "S"
44 (see wiring diagram).
45
46 TECHNICAL DATA
47 Protocol Z-Wave, 868,4MHz
48 Chip Z-Wave 500 chip
49 SDK 6.71.03
50 Rated voltage 230V AC 50Hz
51 Power 1VA - 200VA
52 Input current 0,9A
53 Controls Push and rotary dimmer
54 Operating temperature -20°C - 40 °C
55 Connection Max. 2,5mm2
56 Flush mounting depth 15mm
57 IP Code IP 20
58 Size (LxWxH) 84 x 84 x 43mm
59
60 APPROVALS
61 Z-Wave Plus
62 CE
63 EN 55015/A2: 2009, EN 61547:2009
64 EN 61000-3-2/A2:2009
65 EN 61000-3-3:2008
66 EN 60669-2-1/A12:2010
67 EN 60669-1:A2:2008
68 EMC 2014/30/EU, RoHS 2011/65/EU
69 LVD 2014/35/EU
70 </MetaDataItem>
71 <MetaDataItem name="ExclusionDescription">INCLUSION/EXCLUSION
72 Press the main button on dimmer 6 times in a rapid sequence. Heatit Z-DIM is now included in your Z-Wave network.</MetaDataItem>
73 <MetaDataItem id="2200" name="FrequencyName" type="0003">CEPT (Europe)</MetaDataItem>
74 <MetaDataItem name="Name">Heatit Zdim</MetaDataItem>
75 <MetaDataItem name="ResetDescription">FACTORY RESET - RES
76 By pressing and holding the main button for 20 seconds, the dimmer will perform
77 a complete factory reset. The connected light source will blink once and go in the
78 "OFF" state if successfully reset. NB! Please use this procedure only when the primary
79 controller is missing or otherwise inoperable</MetaDataItem>
80 <MetaDataItem name="InclusionDescription">INCLUSION/EXCLUSION
81 Press the main button on dimmer 6 times in a rapid sequence. Heatit Z-DIM is now included in your Z-Wave network.</MetaDataItem>
82 <ChangeLog>
83 <Entry author="Pål Kristensen - [email protected]" date="10 January 2020" revision="1">Initial release</Entry>
84 <Entry author="Pål Kristensen - [email protected]" date="11 January 2021" revision="2">Fixed COMMAND_CLASS_SWITCH_MULTILEVEL get commands</Entry>
85 </ChangeLog>
86 </MetaData>
87
88 <CommandClass id="112">
89 <Value genre="config" instance="1" index="1" value="0" label="Connected Load" size="1" min="0" max="200" type="byte">
90 <Help>
91 The parameter defines the value of connected load. Refer to Paragraph 8 "Power Metering".
92 0 = Default
93 1 - 200 = 1-200 Watts connected load
94
95 POWER METERING
96 The Heatit Z-Dim has functionality to calculate power consumption. To enable this
97 function, Parameter 1 "Connected load" should have a value greater than 0. This is an
98 estimated value, therefore power consumption accuracy depends on load estimation.
99 1. Estimate the load value (Watt) connected to the Heatit Z-Dim.
100 2. Use this value in Parameter 1.
101 Heatit Z-Dim can report accumulated (kWh) and instant (Watt), or only instant (Watt)
102 power consumption. The report time interval can be altered by Parameter 9.
103 </Help>
104 </Value>
105 <Value genre="config" instance="1" index="2" value="20" label="Minimum Dim level" units="%" size="1" min="1" max="98" type="byte">
106 <Help>
107 The parameter defines the lowest dimming level of the dimmer. The value must be lower than parameter 3 "Maximum Dim Level"
108 1% - 98% Default is 20 (20%)
109 </Help>
110 </Value>
111 <Value genre="config" instance="1" index="3" value="85" label="Maximum Dim level" units="%" size="1" min="2" max="99" type="byte">
112 <Help>
113 The parameter defines the highest dimming level of the dimmer.
114 The value must be higher than parameter 2 "Minimum Dim Level"
115 2% - 99% Default is 85 (85%)
116 </Help>
117 </Value>
118 <Value genre="config" instance="1" index="4" value="15" label="Total steps" units="step" size="1" min="5" max="255" type="byte">
119 <Help>
120 The parameter defines how many steps it should take to dim from minimum
121 to maximum dim level (One round = 20 steps).
122 5 - 255 = 5-255 steps. Default is 15 (3/4 round)
123 </Help>
124 </Value>
125 <Value genre="config" instance="1" index="5" value="0" label="Double press function" size="1" type="list">
126 <Help>The parameter defines the double press functionality. </Help>
127 <Item value="0" label="Central Scene notification (Default)"/>
128 <Item value="1" label="Dim to highest level"/>
129 </Value>
130 <Value genre="config" instance="1" index="6" value="1" label="Scene controller" size="1" type="list">
131 <Help>Enables scene controller</Help>
132 <Item value="0" label="Disabled"/>
133 <Item value="1" label="Active (Default)"/>
134 </Value>
135 <Value genre="config" instance="1" index="7" value="0" label="Switch ON level" units="%" size="1" min="0" max="99" type="byte">
136 <Help>
137 The parameter defines the dimming level when restored from the OFF state
138 by push button.
139 0 = Restores last dim level (Default)
140 1 - 99 = 1% - 99%
141 </Help>
142 </Value>
143 <Value genre="config" instance="1" index="8" value="1" label="Dimming Duration" units="time" size="1" min="0" max="255" type="byte">
144 <Help>
145 The parameter defines how long it takes to dim to the desired level.
146 Note! Only Multilevel Switch Command Class is affected by this parameter.
147 0 = Disabled
148 1 - 127 = Duration in seconds (1 - 127 seconds. Default is 1)
149 128 - 255 = Duration in minutes (1 - 127 minutes)
150 </Help>
151 </Value>
152 <Value genre="config" instance="1" index="9" value="60" label="Meter Report Interval" units="sec" size="2" min="0" max="32767" type="short">
153 <Help>
154 The parameter defines the report interval for Power Metering.
155 30 - 32767 = Duration in seconds (30 - 32 767. Default is 60)
156 </Help>
157 </Value>
158 <Value genre="config" instance="1" index="10" value="50" label="Power restore level" units="%" size="1" min="1" max="99" type="byte">
159 <Help>
160 The parameter defines the initial dimming level after power loss.
161 1 - 99 = 1% - 99% Default is 50 (50%)
162 </Help>
163 </Value>
164 </CommandClass>
165
166 <!-- COMMAND_CLASS_SWITCH_MULTILEVEL. This class is in the list reported by the device, but it does not respond to requests -->
167 <CommandClass id="38">
168 <Compatibility>
169 <GetSupported>false</GetSupported>
170 </Compatibility>
171 </CommandClass>
172
173 <CommandClass id="133">
174 <Associations num_groups="3">
175 <Group index="1" label="Lifeline" max_associations="8" />
176 <Group index="2" label="Dimming level" max_associations="8" auto="true" />
177 <Group index="3" label="State of Device ON/OFF" max_associations="8" auto="true" />
178 </Associations>
179 </CommandClass>
180
181 <CommandClass id="142">
182 <Compatibility>
183 <ForceInstances>true</ForceInstances>
184 </Compatibility>
185 </CommandClass>
186
187 </Product>