| 1 |
Link Layer Validation Device is a standard device for testing of Super |
| 2 |
Speed Link Layer tests. These nodes are available in sysfs only when lvs |
| 3 |
driver is bound with root hub device. |
| 4 |
|
| 5 |
What: /sys/bus/usb/devices/.../get_dev_desc |
| 6 |
Date: March 2014 |
| 7 |
Contact: Pratyush Anand <[email protected]> |
| 8 |
Description: |
| 9 |
Write to this node to issue "Get Device Descriptor" |
| 10 |
for Link Layer Validation device. It is needed for TD.7.06. |
| 11 |
|
| 12 |
What: /sys/bus/usb/devices/.../u1_timeout |
| 13 |
Date: March 2014 |
| 14 |
Contact: Pratyush Anand <[email protected]> |
| 15 |
Description: |
| 16 |
Set "U1 timeout" for the downstream port where Link Layer |
| 17 |
Validation device is connected. Timeout value must be between 0 |
| 18 |
and 127. It is needed for TD.7.18, TD.7.19, TD.7.20 and TD.7.21. |
| 19 |
|
| 20 |
What: /sys/bus/usb/devices/.../u2_timeout |
| 21 |
Date: March 2014 |
| 22 |
Contact: Pratyush Anand <[email protected]> |
| 23 |
Description: |
| 24 |
Set "U2 timeout" for the downstream port where Link Layer |
| 25 |
Validation device is connected. Timeout value must be between 0 |
| 26 |
and 127. It is needed for TD.7.18, TD.7.19, TD.7.20 and TD.7.21. |
| 27 |
|
| 28 |
What: /sys/bus/usb/devices/.../hot_reset |
| 29 |
Date: March 2014 |
| 30 |
Contact: Pratyush Anand <[email protected]> |
| 31 |
Description: |
| 32 |
Write to this node to issue "Reset" for Link Layer Validation |
| 33 |
device. It is needed for TD.7.29, TD.7.31, TD.7.34 and TD.7.35. |
| 34 |
|
| 35 |
What: /sys/bus/usb/devices/.../u3_entry |
| 36 |
Date: March 2014 |
| 37 |
Contact: Pratyush Anand <[email protected]> |
| 38 |
Description: |
| 39 |
Write to this node to issue "U3 entry" for Link Layer |
| 40 |
Validation device. It is needed for TD.7.35 and TD.7.36. |
| 41 |
|
| 42 |
What: /sys/bus/usb/devices/.../u3_exit |
| 43 |
Date: March 2014 |
| 44 |
Contact: Pratyush Anand <[email protected]> |
| 45 |
Description: |
| 46 |
Write to this node to issue "U3 exit" for Link Layer |
| 47 |
Validation device. It is needed for TD.7.36. |
| 48 |
|
| 49 |
What: /sys/bus/usb/devices/.../enable_compliance |
| 50 |
Date: July 2017 |
| 51 |
Description: |
| 52 |
Write to this node to set the port to compliance mode to test |
| 53 |
with Link Layer Validation device. It is needed for TD.7.34. |
| 54 |
|
| 55 |
What: /sys/bus/usb/devices/.../warm_reset |
| 56 |
Date: July 2017 |
| 57 |
Description: |
| 58 |
Write to this node to issue "Warm Reset" for Link Layer Validation |
| 59 |
device. It may be needed to properly reset an xHCI 1.1 host port if |
| 60 |
compliance mode needed to be explicitly enabled. |