| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Ralink MT7620A SoC PCI support |
| 4 |
* |
| 5 |
* Copyright (C) 2007-2013 Bruce Chang (Mediatek) |
| 6 |
* Copyright (C) 2013-2016 John Crispin <[email protected]> |
| 7 |
*/ |
| 8 |
|
| 9 |
#include <linux/types.h> |
| 10 |
#include <linux/pci.h> |
| 11 |
#include <linux/io.h> |
| 12 |
#include <linux/init.h> |
| 13 |
#include <linux/delay.h> |
| 14 |
#include <linux/interrupt.h> |
| 15 |
#include <linux/of.h> |
| 16 |
#include <linux/of_irq.h> |
| 17 |
#include <linux/of_pci.h> |
| 18 |
#include <linux/reset.h> |
| 19 |
#include <linux/platform_device.h> |
| 20 |
|
| 21 |
#include <asm/mach-ralink/ralink_regs.h> |
| 22 |
#include <asm/mach-ralink/mt7620.h> |
| 23 |
|
| 24 |
#define RALINK_PCI_IO_MAP_BASE 0x10160000 |
| 25 |
#define RALINK_PCI_MEMORY_BASE 0x0 |
| 26 |
|
| 27 |
#define RALINK_INT_PCIE0 4 |
| 28 |
|
| 29 |
#define RALINK_CLKCFG1 0x30 |
| 30 |
#define RALINK_GPIOMODE 0x60 |
| 31 |
|
| 32 |
#define PPLL_CFG1 0x9c |
| 33 |
#define PPLL_LD BIT(23) |
| 34 |
|
| 35 |
#define PPLL_DRV 0xa0 |
| 36 |
#define PDRV_SW_SET BIT(31) |
| 37 |
#define LC_CKDRVPD BIT(19) |
| 38 |
#define LC_CKDRVOHZ BIT(18) |
| 39 |
#define LC_CKDRVHZ BIT(17) |
| 40 |
#define LC_CKTEST BIT(16) |
| 41 |
|
| 42 |
/* PCI Bridge registers */ |
| 43 |
#define RALINK_PCI_PCICFG_ADDR 0x00 |
| 44 |
#define PCIRST BIT(1) |
| 45 |
|
| 46 |
#define RALINK_PCI_PCIENA 0x0C |
| 47 |
#define PCIINT2 BIT(20) |
| 48 |
|
| 49 |
#define RALINK_PCI_CONFIG_ADDR 0x20 |
| 50 |
#define RALINK_PCI_CONFIG_DATA_VIRT_REG 0x24 |
| 51 |
#define RALINK_PCI_MEMBASE 0x28 |
| 52 |
#define RALINK_PCI_IOBASE 0x2C |
| 53 |
|
| 54 |
/* PCI RC registers */ |
| 55 |
#define RALINK_PCI0_BAR0SETUP_ADDR 0x10 |
| 56 |
#define RALINK_PCI0_IMBASEBAR0_ADDR 0x18 |
| 57 |
#define RALINK_PCI0_ID 0x30 |
| 58 |
#define RALINK_PCI0_CLASS 0x34 |
| 59 |
#define RALINK_PCI0_SUBID 0x38 |
| 60 |
#define RALINK_PCI0_STATUS 0x50 |
| 61 |
#define PCIE_LINK_UP_ST BIT(0) |
| 62 |
|
| 63 |
#define PCIEPHY0_CFG 0x90 |
| 64 |
|
| 65 |
#define RALINK_PCIEPHY_P0_CTL_OFFSET 0x7498 |
| 66 |
#define RALINK_PCIE0_CLK_EN BIT(26) |
| 67 |
|
| 68 |
#define BUSY 0x80000000 |
| 69 |
#define WAITRETRY_MAX 10 |
| 70 |
#define WRITE_MODE (1UL << 23) |
| 71 |
#define DATA_SHIFT 0 |
| 72 |
#define ADDR_SHIFT 8 |
| 73 |
|
| 74 |
|
| 75 |
static void __iomem *bridge_base; |
| 76 |
static void __iomem *pcie_base; |
| 77 |
|
| 78 |
static struct reset_control *rstpcie0; |
| 79 |
|
| 80 |
static inline void bridge_w32(u32 val, unsigned reg) |
| 81 |
{ |
| 82 |
iowrite32(val, bridge_base + reg); |
| 83 |
} |
| 84 |
|
| 85 |
static inline u32 bridge_r32(unsigned reg) |
| 86 |
{ |
| 87 |
return ioread32(bridge_base + reg); |
| 88 |
} |
| 89 |
|
| 90 |
static inline void pcie_w32(u32 val, unsigned reg) |
| 91 |
{ |
| 92 |
iowrite32(val, pcie_base + reg); |
| 93 |
} |
| 94 |
|
| 95 |
static inline u32 pcie_r32(unsigned reg) |
| 96 |
{ |
| 97 |
return ioread32(pcie_base + reg); |
| 98 |
} |
| 99 |
|
| 100 |
static inline void pcie_m32(u32 clr, u32 set, unsigned reg) |
| 101 |
{ |
| 102 |
u32 val = pcie_r32(reg); |
| 103 |
|
| 104 |
val &= ~clr; |
| 105 |
val |= set; |
| 106 |
pcie_w32(val, reg); |
| 107 |
} |
| 108 |
|
| 109 |
static int wait_pciephy_busy(void) |
| 110 |
{ |
| 111 |
unsigned long reg_value = 0x0, retry = 0; |
| 112 |
|
| 113 |
while (1) { |
| 114 |
reg_value = pcie_r32(PCIEPHY0_CFG); |
| 115 |
|
| 116 |
if (reg_value & BUSY) |
| 117 |
mdelay(100); |
| 118 |
else |
| 119 |
break; |
| 120 |
if (retry++ > WAITRETRY_MAX) { |
| 121 |
pr_warn("PCIE-PHY retry failed.\n"); |
| 122 |
return -1; |
| 123 |
} |
| 124 |
} |
| 125 |
return 0; |
| 126 |
} |
| 127 |
|
| 128 |
static void pcie_phy(unsigned long addr, unsigned long val) |
| 129 |
{ |
| 130 |
wait_pciephy_busy(); |
| 131 |
pcie_w32(WRITE_MODE | (val << DATA_SHIFT) | (addr << ADDR_SHIFT), |
| 132 |
PCIEPHY0_CFG); |
| 133 |
mdelay(1); |
| 134 |
wait_pciephy_busy(); |
| 135 |
} |
| 136 |
|
| 137 |
static int pci_config_read(struct pci_bus *bus, unsigned int devfn, int where, |
| 138 |
int size, u32 *val) |
| 139 |
{ |
| 140 |
unsigned int slot = PCI_SLOT(devfn); |
| 141 |
u8 func = PCI_FUNC(devfn); |
| 142 |
u32 address; |
| 143 |
u32 data; |
| 144 |
u32 num = 0; |
| 145 |
|
| 146 |
if (bus) |
| 147 |
num = bus->number; |
| 148 |
|
| 149 |
address = (((where & 0xF00) >> 8) << 24) | (num << 16) | (slot << 11) | |
| 150 |
(func << 8) | (where & 0xfc) | 0x80000000; |
| 151 |
bridge_w32(address, RALINK_PCI_CONFIG_ADDR); |
| 152 |
data = bridge_r32(RALINK_PCI_CONFIG_DATA_VIRT_REG); |
| 153 |
|
| 154 |
switch (size) { |
| 155 |
case 1: |
| 156 |
*val = (data >> ((where & 3) << 3)) & 0xff; |
| 157 |
break; |
| 158 |
case 2: |
| 159 |
*val = (data >> ((where & 3) << 3)) & 0xffff; |
| 160 |
break; |
| 161 |
case 4: |
| 162 |
*val = data; |
| 163 |
break; |
| 164 |
} |
| 165 |
|
| 166 |
return PCIBIOS_SUCCESSFUL; |
| 167 |
} |
| 168 |
|
| 169 |
static int pci_config_write(struct pci_bus *bus, unsigned int devfn, int where, |
| 170 |
int size, u32 val) |
| 171 |
{ |
| 172 |
unsigned int slot = PCI_SLOT(devfn); |
| 173 |
u8 func = PCI_FUNC(devfn); |
| 174 |
u32 address; |
| 175 |
u32 data; |
| 176 |
u32 num = 0; |
| 177 |
|
| 178 |
if (bus) |
| 179 |
num = bus->number; |
| 180 |
|
| 181 |
address = (((where & 0xF00) >> 8) << 24) | (num << 16) | (slot << 11) | |
| 182 |
(func << 8) | (where & 0xfc) | 0x80000000; |
| 183 |
bridge_w32(address, RALINK_PCI_CONFIG_ADDR); |
| 184 |
data = bridge_r32(RALINK_PCI_CONFIG_DATA_VIRT_REG); |
| 185 |
|
| 186 |
switch (size) { |
| 187 |
case 1: |
| 188 |
data = (data & ~(0xff << ((where & 3) << 3))) | |
| 189 |
(val << ((where & 3) << 3)); |
| 190 |
break; |
| 191 |
case 2: |
| 192 |
data = (data & ~(0xffff << ((where & 3) << 3))) | |
| 193 |
(val << ((where & 3) << 3)); |
| 194 |
break; |
| 195 |
case 4: |
| 196 |
data = val; |
| 197 |
break; |
| 198 |
} |
| 199 |
|
| 200 |
bridge_w32(data, RALINK_PCI_CONFIG_DATA_VIRT_REG); |
| 201 |
|
| 202 |
return PCIBIOS_SUCCESSFUL; |
| 203 |
} |
| 204 |
|
| 205 |
struct pci_ops mt7620_pci_ops = { |
| 206 |
.read = pci_config_read, |
| 207 |
.write = pci_config_write, |
| 208 |
}; |
| 209 |
|
| 210 |
static struct resource mt7620_res_pci_mem1; |
| 211 |
static struct resource mt7620_res_pci_io1; |
| 212 |
struct pci_controller mt7620_controller = { |
| 213 |
.pci_ops = &mt7620_pci_ops, |
| 214 |
.mem_resource = &mt7620_res_pci_mem1, |
| 215 |
.mem_offset = 0x00000000UL, |
| 216 |
.io_resource = &mt7620_res_pci_io1, |
| 217 |
.io_offset = 0x00000000UL, |
| 218 |
.io_map_base = 0xa0000000, |
| 219 |
}; |
| 220 |
|
| 221 |
static int mt7620_pci_hw_init(struct platform_device *pdev) |
| 222 |
{ |
| 223 |
/* bypass PCIe DLL */ |
| 224 |
pcie_phy(0x0, 0x80); |
| 225 |
pcie_phy(0x1, 0x04); |
| 226 |
|
| 227 |
/* Elastic buffer control */ |
| 228 |
pcie_phy(0x68, 0xB4); |
| 229 |
|
| 230 |
/* put core into reset */ |
| 231 |
pcie_m32(0, PCIRST, RALINK_PCI_PCICFG_ADDR); |
| 232 |
reset_control_assert(rstpcie0); |
| 233 |
|
| 234 |
/* disable power and all clocks */ |
| 235 |
rt_sysc_m32(RALINK_PCIE0_CLK_EN, 0, RALINK_CLKCFG1); |
| 236 |
rt_sysc_m32(LC_CKDRVPD, PDRV_SW_SET, PPLL_DRV); |
| 237 |
|
| 238 |
/* bring core out of reset */ |
| 239 |
reset_control_deassert(rstpcie0); |
| 240 |
rt_sysc_m32(0, RALINK_PCIE0_CLK_EN, RALINK_CLKCFG1); |
| 241 |
mdelay(100); |
| 242 |
|
| 243 |
if (!(rt_sysc_r32(PPLL_CFG1) & PPLL_LD)) { |
| 244 |
dev_err(&pdev->dev, "pcie PLL not locked, aborting init\n"); |
| 245 |
reset_control_assert(rstpcie0); |
| 246 |
rt_sysc_m32(RALINK_PCIE0_CLK_EN, 0, RALINK_CLKCFG1); |
| 247 |
return -1; |
| 248 |
} |
| 249 |
|
| 250 |
/* power up the bus */ |
| 251 |
rt_sysc_m32(LC_CKDRVHZ | LC_CKDRVOHZ, LC_CKDRVPD | PDRV_SW_SET, |
| 252 |
PPLL_DRV); |
| 253 |
|
| 254 |
return 0; |
| 255 |
} |
| 256 |
|
| 257 |
static int mt7628_pci_hw_init(struct platform_device *pdev) |
| 258 |
{ |
| 259 |
u32 val = 0; |
| 260 |
|
| 261 |
/* bring the core out of reset */ |
| 262 |
rt_sysc_m32(BIT(16), 0, RALINK_GPIOMODE); |
| 263 |
reset_control_deassert(rstpcie0); |
| 264 |
|
| 265 |
/* enable the pci clk */ |
| 266 |
rt_sysc_m32(0, RALINK_PCIE0_CLK_EN, RALINK_CLKCFG1); |
| 267 |
mdelay(100); |
| 268 |
|
| 269 |
/* voodoo from the SDK driver */ |
| 270 |
pcie_m32(~0xff, 0x5, RALINK_PCIEPHY_P0_CTL_OFFSET); |
| 271 |
|
| 272 |
pci_config_read(NULL, 0, 0x70c, 4, &val); |
| 273 |
val &= ~(0xff) << 8; |
| 274 |
val |= 0x50 << 8; |
| 275 |
pci_config_write(NULL, 0, 0x70c, 4, val); |
| 276 |
|
| 277 |
return 0; |
| 278 |
} |
| 279 |
|
| 280 |
static int mt7620_pci_probe(struct platform_device *pdev) |
| 281 |
{ |
| 282 |
u32 val = 0; |
| 283 |
|
| 284 |
rstpcie0 = devm_reset_control_get_exclusive(&pdev->dev, "pcie0"); |
| 285 |
if (IS_ERR(rstpcie0)) |
| 286 |
return PTR_ERR(rstpcie0); |
| 287 |
|
| 288 |
bridge_base = devm_platform_get_and_ioremap_resource(pdev, 0, NULL); |
| 289 |
if (IS_ERR(bridge_base)) |
| 290 |
return PTR_ERR(bridge_base); |
| 291 |
|
| 292 |
pcie_base = devm_platform_get_and_ioremap_resource(pdev, 1, NULL); |
| 293 |
if (IS_ERR(pcie_base)) |
| 294 |
return PTR_ERR(pcie_base); |
| 295 |
|
| 296 |
iomem_resource.start = 0; |
| 297 |
iomem_resource.end = ~0; |
| 298 |
ioport_resource.start = 0; |
| 299 |
ioport_resource.end = ~0; |
| 300 |
|
| 301 |
/* bring up the pci core */ |
| 302 |
switch (ralink_soc) { |
| 303 |
case MT762X_SOC_MT7620A: |
| 304 |
if (mt7620_pci_hw_init(pdev)) |
| 305 |
return -1; |
| 306 |
break; |
| 307 |
|
| 308 |
case MT762X_SOC_MT7628AN: |
| 309 |
case MT762X_SOC_MT7688: |
| 310 |
if (mt7628_pci_hw_init(pdev)) |
| 311 |
return -1; |
| 312 |
break; |
| 313 |
|
| 314 |
default: |
| 315 |
dev_err(&pdev->dev, "pcie is not supported on this hardware\n"); |
| 316 |
return -1; |
| 317 |
} |
| 318 |
mdelay(50); |
| 319 |
|
| 320 |
/* enable write access */ |
| 321 |
pcie_m32(PCIRST, 0, RALINK_PCI_PCICFG_ADDR); |
| 322 |
mdelay(100); |
| 323 |
|
| 324 |
/* check if there is a card present */ |
| 325 |
if ((pcie_r32(RALINK_PCI0_STATUS) & PCIE_LINK_UP_ST) == 0) { |
| 326 |
reset_control_assert(rstpcie0); |
| 327 |
rt_sysc_m32(RALINK_PCIE0_CLK_EN, 0, RALINK_CLKCFG1); |
| 328 |
if (ralink_soc == MT762X_SOC_MT7620A) |
| 329 |
rt_sysc_m32(LC_CKDRVPD, PDRV_SW_SET, PPLL_DRV); |
| 330 |
dev_info(&pdev->dev, "PCIE0 no card, disable it(RST&CLK)\n"); |
| 331 |
return -1; |
| 332 |
} |
| 333 |
|
| 334 |
/* setup ranges */ |
| 335 |
bridge_w32(0xffffffff, RALINK_PCI_MEMBASE); |
| 336 |
bridge_w32(RALINK_PCI_IO_MAP_BASE, RALINK_PCI_IOBASE); |
| 337 |
|
| 338 |
pcie_w32(0x7FFF0001, RALINK_PCI0_BAR0SETUP_ADDR); |
| 339 |
pcie_w32(RALINK_PCI_MEMORY_BASE, RALINK_PCI0_IMBASEBAR0_ADDR); |
| 340 |
pcie_w32(0x06040001, RALINK_PCI0_CLASS); |
| 341 |
|
| 342 |
/* enable interrupts */ |
| 343 |
pcie_m32(0, PCIINT2, RALINK_PCI_PCIENA); |
| 344 |
|
| 345 |
/* voodoo from the SDK driver */ |
| 346 |
pci_config_read(NULL, 0, 4, 4, &val); |
| 347 |
pci_config_write(NULL, 0, 4, 4, val | 0x7); |
| 348 |
|
| 349 |
pci_load_of_ranges(&mt7620_controller, pdev->dev.of_node); |
| 350 |
register_pci_controller(&mt7620_controller); |
| 351 |
|
| 352 |
return 0; |
| 353 |
} |
| 354 |
|
| 355 |
int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) |
| 356 |
{ |
| 357 |
u16 cmd; |
| 358 |
u32 val; |
| 359 |
int irq = 0; |
| 360 |
|
| 361 |
if ((dev->bus->number == 0) && (slot == 0)) { |
| 362 |
pcie_w32(0x7FFF0001, RALINK_PCI0_BAR0SETUP_ADDR); |
| 363 |
pci_config_write(dev->bus, 0, PCI_BASE_ADDRESS_0, 4, |
| 364 |
RALINK_PCI_MEMORY_BASE); |
| 365 |
pci_config_read(dev->bus, 0, PCI_BASE_ADDRESS_0, 4, &val); |
| 366 |
} else if ((dev->bus->number == 1) && (slot == 0x0)) { |
| 367 |
irq = RALINK_INT_PCIE0; |
| 368 |
} else { |
| 369 |
dev_err(&dev->dev, "no irq found - bus=0x%x, slot = 0x%x\n", |
| 370 |
dev->bus->number, slot); |
| 371 |
return 0; |
| 372 |
} |
| 373 |
dev_info(&dev->dev, "card - bus=0x%x, slot = 0x%x irq=%d\n", |
| 374 |
dev->bus->number, slot, irq); |
| 375 |
|
| 376 |
/* configure the cache line size to 0x14 */ |
| 377 |
pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 0x14); |
| 378 |
|
| 379 |
/* configure latency timer to 0xff */ |
| 380 |
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xff); |
| 381 |
pci_read_config_word(dev, PCI_COMMAND, &cmd); |
| 382 |
|
| 383 |
/* setup the slot */ |
| 384 |
cmd = cmd | PCI_COMMAND_MASTER | PCI_COMMAND_IO | PCI_COMMAND_MEMORY; |
| 385 |
pci_write_config_word(dev, PCI_COMMAND, cmd); |
| 386 |
pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq); |
| 387 |
|
| 388 |
return irq; |
| 389 |
} |
| 390 |
|
| 391 |
int pcibios_plat_dev_init(struct pci_dev *dev) |
| 392 |
{ |
| 393 |
return 0; |
| 394 |
} |
| 395 |
|
| 396 |
static const struct of_device_id mt7620_pci_ids[] = { |
| 397 |
{ .compatible = "mediatek,mt7620-pci" }, |
| 398 |
{}, |
| 399 |
}; |
| 400 |
|
| 401 |
static struct platform_driver mt7620_pci_driver = { |
| 402 |
.probe = mt7620_pci_probe, |
| 403 |
.driver = { |
| 404 |
.name = "mt7620-pci", |
| 405 |
.of_match_table = of_match_ptr(mt7620_pci_ids), |
| 406 |
}, |
| 407 |
}; |
| 408 |
|
| 409 |
static int __init mt7620_pci_init(void) |
| 410 |
{ |
| 411 |
return platform_driver_register(&mt7620_pci_driver); |
| 412 |
} |
| 413 |
|
| 414 |
arch_initcall(mt7620_pci_init); |