| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Copyright (C) 2011 - 2014 Xilinx |
| 4 |
* Copyright (C) 2012 National Instruments Corp. |
| 5 |
*/ |
| 6 |
/dts-v1/; |
| 7 |
#include "zynq-7000.dtsi" |
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "Xilinx ZC702 board"; |
| 12 |
compatible = "xlnx,zynq-zc702", "xlnx,zynq-7000"; |
| 13 |
|
| 14 |
aliases { |
| 15 |
ethernet0 = &gem0; |
| 16 |
i2c0 = &i2c0; |
| 17 |
serial0 = &uart1; |
| 18 |
spi0 = &qspi; |
| 19 |
mmc0 = &sdhci0; |
| 20 |
nvmem0 = &eeprom; |
| 21 |
rtc0 = &rtc; |
| 22 |
}; |
| 23 |
|
| 24 |
memory@0 { |
| 25 |
device_type = "memory"; |
| 26 |
reg = <0x0 0x40000000>; |
| 27 |
}; |
| 28 |
|
| 29 |
chosen { |
| 30 |
bootargs = ""; |
| 31 |
stdout-path = "serial0:115200n8"; |
| 32 |
}; |
| 33 |
|
| 34 |
gpio-keys { |
| 35 |
compatible = "gpio-keys"; |
| 36 |
autorepeat; |
| 37 |
switch-14 { |
| 38 |
label = "sw14"; |
| 39 |
gpios = <&gpio0 12 0>; |
| 40 |
linux,code = <108>; /* down */ |
| 41 |
wakeup-source; |
| 42 |
autorepeat; |
| 43 |
}; |
| 44 |
switch-13 { |
| 45 |
label = "sw13"; |
| 46 |
gpios = <&gpio0 14 0>; |
| 47 |
linux,code = <103>; /* up */ |
| 48 |
wakeup-source; |
| 49 |
autorepeat; |
| 50 |
}; |
| 51 |
}; |
| 52 |
|
| 53 |
leds { |
| 54 |
compatible = "gpio-leds"; |
| 55 |
|
| 56 |
led-ds23 { |
| 57 |
label = "ds23"; |
| 58 |
gpios = <&gpio0 10 0>; |
| 59 |
linux,default-trigger = "heartbeat"; |
| 60 |
}; |
| 61 |
}; |
| 62 |
|
| 63 |
usb_phy0: phy0 { |
| 64 |
compatible = "usb-nop-xceiv"; |
| 65 |
#phy-cells = <0>; |
| 66 |
}; |
| 67 |
}; |
| 68 |
|
| 69 |
&can0 { |
| 70 |
status = "okay"; |
| 71 |
pinctrl-names = "default"; |
| 72 |
pinctrl-0 = <&pinctrl_can0_default>; |
| 73 |
}; |
| 74 |
|
| 75 |
&clkc { |
| 76 |
ps-clk-frequency = <33333333>; |
| 77 |
}; |
| 78 |
|
| 79 |
&gem0 { |
| 80 |
status = "okay"; |
| 81 |
phy-mode = "rgmii-id"; |
| 82 |
phy-handle = <ðernet_phy>; |
| 83 |
pinctrl-names = "default"; |
| 84 |
pinctrl-0 = <&pinctrl_gem0_default>; |
| 85 |
|
| 86 |
ethernet_phy: ethernet-phy@7 { |
| 87 |
reg = <7>; |
| 88 |
}; |
| 89 |
}; |
| 90 |
|
| 91 |
&gpio0 { |
| 92 |
pinctrl-names = "default"; |
| 93 |
pinctrl-0 = <&pinctrl_gpio0_default>; |
| 94 |
}; |
| 95 |
|
| 96 |
&i2c0 { |
| 97 |
status = "okay"; |
| 98 |
clock-frequency = <400000>; |
| 99 |
pinctrl-names = "default", "gpio"; |
| 100 |
pinctrl-0 = <&pinctrl_i2c0_default>; |
| 101 |
pinctrl-1 = <&pinctrl_i2c0_gpio>; |
| 102 |
scl-gpios = <&gpio0 50 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 103 |
sda-gpios = <&gpio0 51 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| 104 |
|
| 105 |
i2c-mux@74 { |
| 106 |
compatible = "nxp,pca9548"; |
| 107 |
#address-cells = <1>; |
| 108 |
#size-cells = <0>; |
| 109 |
reg = <0x74>; |
| 110 |
|
| 111 |
i2c@0 { |
| 112 |
#address-cells = <1>; |
| 113 |
#size-cells = <0>; |
| 114 |
reg = <0>; |
| 115 |
si570: clock-generator@5d { |
| 116 |
#clock-cells = <0>; |
| 117 |
compatible = "silabs,si570"; |
| 118 |
temperature-stability = <50>; |
| 119 |
reg = <0x5d>; |
| 120 |
factory-fout = <156250000>; |
| 121 |
clock-frequency = <148500000>; |
| 122 |
}; |
| 123 |
}; |
| 124 |
|
| 125 |
i2c@1 { |
| 126 |
#address-cells = <1>; |
| 127 |
#size-cells = <0>; |
| 128 |
reg = <1>; |
| 129 |
adv7511: hdmi-tx@39 { |
| 130 |
compatible = "adi,adv7511"; |
| 131 |
reg = <0x39>; |
| 132 |
adi,input-depth = <8>; |
| 133 |
adi,input-colorspace = "yuv422"; |
| 134 |
adi,input-clock = "1x"; |
| 135 |
adi,input-style = <3>; |
| 136 |
adi,input-justification = "right"; |
| 137 |
}; |
| 138 |
}; |
| 139 |
|
| 140 |
i2c@2 { |
| 141 |
#address-cells = <1>; |
| 142 |
#size-cells = <0>; |
| 143 |
reg = <2>; |
| 144 |
eeprom: eeprom@54 { |
| 145 |
compatible = "atmel,24c08"; |
| 146 |
reg = <0x54>; |
| 147 |
}; |
| 148 |
}; |
| 149 |
|
| 150 |
i2c@3 { |
| 151 |
#address-cells = <1>; |
| 152 |
#size-cells = <0>; |
| 153 |
reg = <3>; |
| 154 |
gpio@21 { |
| 155 |
compatible = "ti,tca6416"; |
| 156 |
reg = <0x21>; |
| 157 |
gpio-controller; |
| 158 |
#gpio-cells = <2>; |
| 159 |
}; |
| 160 |
}; |
| 161 |
|
| 162 |
i2c@4 { |
| 163 |
#address-cells = <1>; |
| 164 |
#size-cells = <0>; |
| 165 |
reg = <4>; |
| 166 |
rtc: rtc@51 { |
| 167 |
compatible = "nxp,pcf8563"; |
| 168 |
reg = <0x51>; |
| 169 |
}; |
| 170 |
}; |
| 171 |
|
| 172 |
i2c@7 { |
| 173 |
#address-cells = <1>; |
| 174 |
#size-cells = <0>; |
| 175 |
reg = <7>; |
| 176 |
hwmon@34 { |
| 177 |
compatible = "ti,ucd9248"; |
| 178 |
reg = <0x34>; |
| 179 |
}; |
| 180 |
hwmon@35 { |
| 181 |
compatible = "ti,ucd9248"; |
| 182 |
reg = <0x35>; |
| 183 |
}; |
| 184 |
hwmon@36 { |
| 185 |
compatible = "ti,ucd9248"; |
| 186 |
reg = <0x36>; |
| 187 |
}; |
| 188 |
}; |
| 189 |
}; |
| 190 |
}; |
| 191 |
|
| 192 |
&pinctrl0 { |
| 193 |
pinctrl_can0_default: can0-default { |
| 194 |
mux { |
| 195 |
function = "can0"; |
| 196 |
groups = "can0_9_grp"; |
| 197 |
}; |
| 198 |
|
| 199 |
conf { |
| 200 |
groups = "can0_9_grp"; |
| 201 |
slew-rate = <0>; |
| 202 |
power-source = <1>; |
| 203 |
}; |
| 204 |
|
| 205 |
conf-rx { |
| 206 |
pins = "MIO46"; |
| 207 |
bias-high-impedance; |
| 208 |
}; |
| 209 |
|
| 210 |
conf-tx { |
| 211 |
pins = "MIO47"; |
| 212 |
bias-disable; |
| 213 |
}; |
| 214 |
}; |
| 215 |
|
| 216 |
pinctrl_gem0_default: gem0-default { |
| 217 |
mux { |
| 218 |
function = "ethernet0"; |
| 219 |
groups = "ethernet0_0_grp"; |
| 220 |
}; |
| 221 |
|
| 222 |
conf { |
| 223 |
groups = "ethernet0_0_grp"; |
| 224 |
slew-rate = <0>; |
| 225 |
power-source = <4>; |
| 226 |
}; |
| 227 |
|
| 228 |
conf-rx { |
| 229 |
pins = "MIO22", "MIO23", "MIO24", "MIO25", "MIO26", "MIO27"; |
| 230 |
bias-high-impedance; |
| 231 |
low-power-disable; |
| 232 |
}; |
| 233 |
|
| 234 |
conf-tx { |
| 235 |
pins = "MIO16", "MIO17", "MIO18", "MIO19", "MIO20", "MIO21"; |
| 236 |
bias-disable; |
| 237 |
low-power-enable; |
| 238 |
}; |
| 239 |
|
| 240 |
mux-mdio { |
| 241 |
function = "mdio0"; |
| 242 |
groups = "mdio0_0_grp"; |
| 243 |
}; |
| 244 |
|
| 245 |
conf-mdio { |
| 246 |
groups = "mdio0_0_grp"; |
| 247 |
slew-rate = <0>; |
| 248 |
power-source = <1>; |
| 249 |
bias-disable; |
| 250 |
}; |
| 251 |
}; |
| 252 |
|
| 253 |
pinctrl_gpio0_default: gpio0-default { |
| 254 |
mux { |
| 255 |
function = "gpio0"; |
| 256 |
groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp", |
| 257 |
"gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp", |
| 258 |
"gpio0_13_grp", "gpio0_14_grp"; |
| 259 |
}; |
| 260 |
|
| 261 |
conf { |
| 262 |
groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp", |
| 263 |
"gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp", |
| 264 |
"gpio0_13_grp", "gpio0_14_grp"; |
| 265 |
slew-rate = <0>; |
| 266 |
power-source = <1>; |
| 267 |
}; |
| 268 |
|
| 269 |
conf-pull-up { |
| 270 |
pins = "MIO9", "MIO10", "MIO11", "MIO12", "MIO13", "MIO14"; |
| 271 |
bias-pull-up; |
| 272 |
}; |
| 273 |
|
| 274 |
conf-pull-none { |
| 275 |
pins = "MIO7", "MIO8"; |
| 276 |
bias-disable; |
| 277 |
}; |
| 278 |
}; |
| 279 |
|
| 280 |
pinctrl_i2c0_default: i2c0-default { |
| 281 |
mux { |
| 282 |
groups = "i2c0_10_grp"; |
| 283 |
function = "i2c0"; |
| 284 |
}; |
| 285 |
|
| 286 |
conf { |
| 287 |
groups = "i2c0_10_grp"; |
| 288 |
bias-pull-up; |
| 289 |
slew-rate = <0>; |
| 290 |
power-source = <1>; |
| 291 |
}; |
| 292 |
}; |
| 293 |
|
| 294 |
pinctrl_i2c0_gpio: i2c0-gpio-grp { |
| 295 |
mux { |
| 296 |
groups = "gpio0_50_grp", "gpio0_51_grp"; |
| 297 |
function = "gpio0"; |
| 298 |
}; |
| 299 |
|
| 300 |
conf { |
| 301 |
groups = "gpio0_50_grp", "gpio0_51_grp"; |
| 302 |
slew-rate = <0>; |
| 303 |
power-source = <1>; |
| 304 |
}; |
| 305 |
}; |
| 306 |
|
| 307 |
pinctrl_sdhci0_default: sdhci0-default { |
| 308 |
mux { |
| 309 |
groups = "sdio0_2_grp"; |
| 310 |
function = "sdio0"; |
| 311 |
}; |
| 312 |
|
| 313 |
conf { |
| 314 |
groups = "sdio0_2_grp"; |
| 315 |
slew-rate = <0>; |
| 316 |
power-source = <1>; |
| 317 |
bias-disable; |
| 318 |
}; |
| 319 |
|
| 320 |
mux-cd { |
| 321 |
groups = "gpio0_0_grp"; |
| 322 |
function = "sdio0_cd"; |
| 323 |
}; |
| 324 |
|
| 325 |
conf-cd { |
| 326 |
groups = "gpio0_0_grp"; |
| 327 |
bias-high-impedance; |
| 328 |
bias-pull-up; |
| 329 |
slew-rate = <0>; |
| 330 |
power-source = <1>; |
| 331 |
}; |
| 332 |
|
| 333 |
mux-wp { |
| 334 |
groups = "gpio0_15_grp"; |
| 335 |
function = "sdio0_wp"; |
| 336 |
}; |
| 337 |
|
| 338 |
conf-wp { |
| 339 |
groups = "gpio0_15_grp"; |
| 340 |
bias-high-impedance; |
| 341 |
bias-pull-up; |
| 342 |
slew-rate = <0>; |
| 343 |
power-source = <1>; |
| 344 |
}; |
| 345 |
}; |
| 346 |
|
| 347 |
pinctrl_uart1_default: uart1-default { |
| 348 |
mux { |
| 349 |
groups = "uart1_10_grp"; |
| 350 |
function = "uart1"; |
| 351 |
}; |
| 352 |
|
| 353 |
conf { |
| 354 |
groups = "uart1_10_grp"; |
| 355 |
slew-rate = <0>; |
| 356 |
power-source = <1>; |
| 357 |
}; |
| 358 |
|
| 359 |
conf-rx { |
| 360 |
pins = "MIO49"; |
| 361 |
bias-high-impedance; |
| 362 |
}; |
| 363 |
|
| 364 |
conf-tx { |
| 365 |
pins = "MIO48"; |
| 366 |
bias-disable; |
| 367 |
}; |
| 368 |
}; |
| 369 |
|
| 370 |
pinctrl_usb0_default: usb0-default { |
| 371 |
mux { |
| 372 |
groups = "usb0_0_grp"; |
| 373 |
function = "usb0"; |
| 374 |
}; |
| 375 |
|
| 376 |
conf { |
| 377 |
groups = "usb0_0_grp"; |
| 378 |
slew-rate = <0>; |
| 379 |
power-source = <1>; |
| 380 |
}; |
| 381 |
|
| 382 |
conf-rx { |
| 383 |
pins = "MIO29", "MIO31", "MIO36"; |
| 384 |
bias-high-impedance; |
| 385 |
}; |
| 386 |
|
| 387 |
conf-tx { |
| 388 |
pins = "MIO28", "MIO30", "MIO32", "MIO33", "MIO34", |
| 389 |
"MIO35", "MIO37", "MIO38", "MIO39"; |
| 390 |
bias-disable; |
| 391 |
}; |
| 392 |
}; |
| 393 |
}; |
| 394 |
|
| 395 |
&qspi { |
| 396 |
bootph-all; |
| 397 |
status = "okay"; |
| 398 |
num-cs = <1>; |
| 399 |
flash@0 { |
| 400 |
compatible = "jedec,spi-nor"; |
| 401 |
reg = <0x0>; |
| 402 |
spi-tx-bus-width = <1>; |
| 403 |
spi-rx-bus-width = <4>; |
| 404 |
spi-max-frequency = <50000000>; |
| 405 |
partitions { |
| 406 |
compatible = "fixed-partitions"; |
| 407 |
#address-cells = <1>; |
| 408 |
#size-cells = <1>; |
| 409 |
partition@0 { |
| 410 |
label = "qspi-fsbl-uboot"; |
| 411 |
reg = <0x0 0x100000>; |
| 412 |
}; |
| 413 |
partition@100000 { |
| 414 |
label = "qspi-linux"; |
| 415 |
reg = <0x100000 0x500000>; |
| 416 |
}; |
| 417 |
partition@600000 { |
| 418 |
label = "qspi-device-tree"; |
| 419 |
reg = <0x600000 0x20000>; |
| 420 |
}; |
| 421 |
partition@620000 { |
| 422 |
label = "qspi-rootfs"; |
| 423 |
reg = <0x620000 0x5e0000>; |
| 424 |
}; |
| 425 |
partition@c00000 { |
| 426 |
label = "qspi-bitstream"; |
| 427 |
reg = <0xc00000 0x400000>; |
| 428 |
}; |
| 429 |
}; |
| 430 |
}; |
| 431 |
}; |
| 432 |
|
| 433 |
&sdhci0 { |
| 434 |
bootph-all; |
| 435 |
status = "okay"; |
| 436 |
pinctrl-names = "default"; |
| 437 |
pinctrl-0 = <&pinctrl_sdhci0_default>; |
| 438 |
}; |
| 439 |
|
| 440 |
&uart1 { |
| 441 |
bootph-all; |
| 442 |
status = "okay"; |
| 443 |
pinctrl-names = "default"; |
| 444 |
pinctrl-0 = <&pinctrl_uart1_default>; |
| 445 |
}; |
| 446 |
|
| 447 |
&usb0 { |
| 448 |
status = "okay"; |
| 449 |
dr_mode = "host"; |
| 450 |
usb-phy = <&usb_phy0>; |
| 451 |
pinctrl-names = "default"; |
| 452 |
pinctrl-0 = <&pinctrl_usb0_default>; |
| 453 |
}; |