Debian Codegraph @

config/rc288dpi

raw
1 # $Id$
2 #
3 # HylaFAX Facsimile Software
4 #
5 # Copyright (c) 1990-1996 Sam Leffler
6 # Copyright (c) 1991-1996 Silicon Graphics, Inc.
7 # HylaFAX is a trademark of Silicon Graphics, Inc.
8 #
9 # Permission to use, copy, modify, distribute, and sell this software and
10 # its documentation for any purpose is hereby granted without fee, provided
11 # that (i) the above copyright notices and this permission notice appear in
12 # all copies of the software and related documentation, and (ii) the names of
13 # Sam Leffler and Silicon Graphics may not be used in any advertising or
14 # publicity relating to the software without the specific, prior written
15 # permission of Sam Leffler and Silicon Graphics.
16 #
17 # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
18 # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
19 # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
20 #
21 # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
22 # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
23 # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
24 # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
25 # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
26 # OF THIS SOFTWARE.
27 #
28
29 #
30 # Configuration for a Rockwell RC288DPi-based Class 2 modem
31 # (should also work for 144DPi-based modems).
32 # Microcom DeskPorte 28.8S firmware rev V1.100K-V34_DS
33 # (and others)
34 #
35 # NB: DCD is toggled at page end during transmits; this can
36 # cause problems on systems where it's not possible to
37 # set CLOCAL and also enable RTS/CTS flow control.
38 #
39 # CONFIG: CLASS2: ROCKWELL-AC/V34-*
40 # CONFIG: CLASS2: "Supra Corporation"-"Supra 288i Sp"-*
41 # CONFIG: CLASS2: "BEST DATA PRODUCTS"-"2834VF"-*
42 # CONFIG: CLASS2: Boca*-33,600*-*
43 #
44 # BEGIN-SERVER
45 # END-SERVER
46 #
47 # Modem-related stuff: should reflect modem command interface
48 # and hardware connection/cabling (e.g. flow control).
49 #
50 ModemType: Class2 # use class 1 interface
51 ModemRate: 19200 # locked for fax sending&receiving
52 ModemFlowControl: rtscts # default
53 #
54 ModemNoFlowCmd: AT&K0 # disable flow control cmd
55 ModemSoftFlowCmd: AT&K4 # software flow control cmd
56 ModemHardFlowCmd: AT&K3 # hardware flow control cmd
57 ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
58 ModemSetupDCDCmd: AT&C1 # DCD follows carrier
59 ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in Class 2
60 #
61 ModemRecvFillOrder: MSB2LSB # bit order of received facsimile
62 ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
63 #
64 ModemDialCmd: ATDT%s # T for tone dialing
65 #
66 # Chip locks the line rate and switches to xon/xoff flow
67 # control when receiving facsimile--we must follow suit.
68 #
69 ModemAnswerFaxBeginCmd: "<19200><xon>" # lock line rate & switch flow control
70 #
71 Class2RecvDataTrigger: "\022" # character sent to modem to start recv
72 Class2BUGCmd: none # AC/V34 gives ERROR
73 Class2APQueryCmd: none # AC/V34 gives ERROR