Debian Codegraph @

config/att-dataport

raw
1 # $Id$
2 #
3 # HylaFAX Facsimile Software
4 #
5 # Copyright (c) 1990-1996 Sam Leffler
6 # Copyright (c) 1991-1996 Silicon Graphics, Inc.
7 # HylaFAX is a trademark of Silicon Graphics, Inc.
8 #
9 # Permission to use, copy, modify, distribute, and sell this software and
10 # its documentation for any purpose is hereby granted without fee, provided
11 # that (i) the above copyright notices and this permission notice appear in
12 # all copies of the software and related documentation, and (ii) the names of
13 # Sam Leffler and Silicon Graphics may not be used in any advertising or
14 # publicity relating to the software without the specific, prior written
15 # permission of Sam Leffler and Silicon Graphics.
16 #
17 # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
18 # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
19 # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
20 #
21 # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
22 # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
23 # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
24 # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
25 # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
26 # OF THIS SOFTWARE.
27 #
28
29 #
30 # Configuration for using the Class 1 command interface with
31 # an AT&T DataPort 14.4 modem. Firmware version 122 (ati1)
32 # or newer.
33 #
34 # Hardware flow control is used by default.
35 #
36 # Note that due to a bug in the 1.22 firmware the FCS bytes in the HDLC
37 # frames are NOT returned to the host. This is fixed in versions 1.33
38 # and later. To deal with this problem, early firmware revs should be
39 # sure to have Class1FrameOverhead set to 2 instead of the normal 4.
40 #
41 # CONFIG:CLASS1:144:.*:.*: Manufacturer='AT&T' Model=Dataport
42 #
43 # BEGIN-SERVER
44 # END-SERVER
45 #
46 # Modem-related stuff: should reflect modem command interface
47 # and hardware connection/cabling (e.g. flow control).
48 #
49 ModemType: Class1 # use class 1 interface
50 ModemRate: 19200
51 ModemFlowControl: rtscts # default
52 #
53 ModemHardFlowCmd: AT&R0\D1\Q3 # use RTS/CTS and enable RS232 handling
54 ModemSoftFlowCmd: AT&R1\D0\Q1 # use RTS/CTS and enable RS232 handling
55 ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
56 ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
57 ModemSetupAACmd: AT+FAA=0 # disable in case of Class 2 support
58 #
59 ModemMfrQueryCmd: !AT&T
60 ModemModelQueryCmd: !DataPort
61 ModemRevQueryCmd: ATI19
62 #
63 # NB: this works around a bug in the 1.22 firmware; it is fixed
64 # in versions 1.33 and later in which case you can remove this
65 # line and use the default value of 4 (though leaving it as 2
66 # won't harm anything).
67 #
68 Class1FrameOverhead: 2 # 1.22 firmware does not include FCS
69 #
70 # The modem returns "OK" when there is a timeout before carrier is
71 # established. This is treated as "NO CARRIER" by faxd. Thus we
72 # need to up the NoCarrierRetrys parameter to avoid having the server
73 # reject jobs prematurely.
74 #
75 NoCarrierRetrys: 3 # retry 3 times on no carrier
76 #
77 PagerSetupCmds: ATS41=10%B300 # use V.21 at 300 bps