Debian Codegraph @

config/rc144ac

raw
1 # $Id$
2 #
3 # HylaFAX Facsimile Software
4 #
5 # Copyright (c) 1990-1996 Sam Leffler
6 # Copyright (c) 1991-1996 Silicon Graphics, Inc.
7 # HylaFAX is a trademark of Silicon Graphics, Inc.
8 #
9 # Permission to use, copy, modify, distribute, and sell this software and
10 # its documentation for any purpose is hereby granted without fee, provided
11 # that (i) the above copyright notices and this permission notice appear in
12 # all copies of the software and related documentation, and (ii) the names of
13 # Sam Leffler and Silicon Graphics may not be used in any advertising or
14 # publicity relating to the software without the specific, prior written
15 # permission of Sam Leffler and Silicon Graphics.
16 #
17 # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
18 # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
19 # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
20 #
21 # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
22 # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
23 # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
24 # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
25 # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
26 # OF THIS SOFTWARE.
27 #
28
29 #
30 # Configuration for a Rockwell V.32AC Class 2 modem
31 # (RC144AC, RC96AC or using RC144DP).
32 # Boca M1440E firmware V1.270 or newer
33 # Dallas Fax (throw it away!)
34 # Hayes Optima 24+Fax96 firmware TR00-J260-001 XXX or newer
35 # SupraFAX v.32bis firmware V1.200-C or newer
36 # Twincom 144/DF firmware rev V1.200 or newer
37 # Dynalink 1414VE firmware rev ???
38 # (and others)
39 #
40 # This configuration file sets up the modem to run at 38.4 with
41 # RTS/CTS flow control used by default. XON/XOFF is automatically
42 # enabled for fax recv. Beware of modems that also lock sending
43 # to 19.2; add ModemSendBeginCmd: "<19200>" if this is required.
44 # Also beware that the adaptive-answer facility, when supported,
45 # is often unreliable.
46 #
47 # CONFIG: CLASS2: *-V.32AC-*
48 #
49 # BEGIN-SERVER
50 # END-SERVER
51 #
52 # Modem-related stuff: should reflect modem command interface
53 # and hardware connection/cabling (e.g. flow control).
54 #
55 ModemType: Class2 # use class 2 interface
56 ModemRate: 19200
57 ModemFlowControl: rtscts # default
58 #
59 #ModemResetCmds: AT&F2 # what you want for a Supra
60 ModemNoFlowCmd: AT&K # disable flow control cmd
61 ModemHardFlowCmd: AT&K3 # hardware flow control cmd
62 ModemSoftFlowCmd: AT&K4 # software flow control cmd
63 ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
64 #ModemSetupDTRCmd: AT&D2S25=1S38=0 # Dynalink 1414VE needs this
65 ModemSetupDCDCmd: AT&C1 # DCD follows carrier
66 ModemSetupAACmd: AT+FAA=1+FCLASS=0 # enable in current class
67 #
68 ModemSendFillOrder: LSB2MSB # as expected
69 ModemRecvFillOrder: MSB2LSB # opposite of what makes sense
70 #
71 ModemAnswerFaxBeginCmd: "<19200><xon>" # modem switches on fax receive
72 #
73 # Caller ID configuration setup for Supra.
74 #
75 #QualifyCID: etc/cid # CID access control list file
76 #CallIDPattern: "NMBR = " # pattern string for phone number info
77 #CallIDPattern: "NAME = " # pattern string for identity info