| 1 |
# -*- po -*- |
| 2 |
# Japanese translations for 1.2.1 package. |
| 3 |
# Copyright (C) 2009-2011, Brazil, Inc |
| 4 |
# This file is distributed under the same license as the groonga package. |
| 5 |
# Kouhei Sutou <[email protected]>, 2011. |
| 6 |
msgid "" |
| 7 |
msgstr "" |
| 8 |
"Project-Id-Version: 1.2.1\n" |
| 9 |
"Report-Msgid-Bugs-To: \n" |
| 10 |
"PO-Revision-Date: 2022-02-09 09:45+0900\n" |
| 11 |
"Language-Team: Japanese\n" |
| 12 |
"Language: ja\n" |
| 13 |
"MIME-Version: 1.0\n" |
| 14 |
"Content-Type: text/plain; charset=UTF-8\n" |
| 15 |
"Content-Transfer-Encoding: 8bit\n" |
| 16 |
"Plural-Forms: nplurals=1; plural=0;\n" |
| 17 |
|
| 18 |
msgid "Execution example::" |
| 19 |
msgstr "実行例::" |
| 20 |
|
| 21 |
msgid "``NormalizerAuto``" |
| 22 |
msgstr "" |
| 23 |
|
| 24 |
msgid "Summary" |
| 25 |
msgstr "概要" |
| 26 |
|
| 27 |
msgid "Normally you should use ``NormalizerAuto`` normalizer. ``NormalizerAuto`` was the normalizer for Groonga 2.0.9 or earlier. ``KEY_NORMALIZE`` flag in ``table_create`` on Groonga 2.0.9 or earlier equals to ``--normalizer NormalizerAuto`` option in ``table_create`` on Groonga 2.1.0 or later." |
| 28 |
msgstr "通常は ``NormalizerAuto`` ノーマライザーを使うべきです。 ``NormalizerAuto`` はGroonga 2.0.9以前で使っていたノーマライザーと同じものです。2.0.9以前のGroongaの ``table_create`` の ``KEY_NORMALIZE`` フラグは、2.1.0以降のGroongaの ``table_create`` の ``--normalizer NormalizerAuto`` と同じです。" |
| 29 |
|
| 30 |
msgid "``NormalizerAuto`` supports all encoding. It uses Unicode NFKC (Normalization Form Compatibility Composition) for UTF-8 encoding text. It uses encoding specific original normalization for other encodings. The results of those original normalization are similar to NFKC." |
| 31 |
msgstr "``NormalizerAuto`` はすべてのエンコーディングに対応しています。UTF-8でエンコードされたテキストにはUnicodeのNFKC(Normalization Form Compatibility Composition)を使います。他のエンコーディング用にはエンコーディング毎に独自の正規化をします。これらの独自の正規化の結果はNFKCでの結果と似たものになります。" |
| 32 |
|
| 33 |
msgid "Syntax" |
| 34 |
msgstr "構文" |
| 35 |
|
| 36 |
msgid "``NormalizerAuto`` hasn't parameter::" |
| 37 |
msgstr "``NormalizerAuto`` には引数はありません。::" |
| 38 |
|
| 39 |
msgid "Usage" |
| 40 |
msgstr "使い方" |
| 41 |
|
| 42 |
msgid "``NormalizerAuto`` normalizes half-width katakana (such as U+FF76 HALFWIDTH KATAKANA LETTER KA) + half-width katakana voiced sound mark (U+FF9E HALFWIDTH KATAKANA VOICED SOUND MARK) to full-width katakana with voiced sound mark (U+30AC KATAKANA LETTER GA). The former is two characters but the latter is one character." |
| 43 |
msgstr "``NormalizerAuto`` は、半角カタカナ(例えば「カ」: U+FF76 HALFWIDTH KATAKANA LETTER KA) + 半角カタカナの濁点(「゙」: U+FF9E HALFWIDTH KATAKANA VOICED SOUND MARK)を濁点付きの全角カタカナ(「ガ」: U+30AC KATAKANA LETTER GA)に正規化します。前者は2文字ですが、後者は1文字です。" |
| 44 |
|
| 45 |
msgid "Here is an example that uses ``NormalizerAuto`` normalizer:" |
| 46 |
msgstr "以下は ``NormalizerAuto`` ノーマライザーを使う例です。" |
| 47 |
|
| 48 |
msgid "See also" |
| 49 |
msgstr "参考" |
| 50 |
|
| 51 |
msgid ":doc:`../commands/normalize`" |
| 52 |
msgstr "" |