| 1 |
.\" Jean II - HPLB - 1996 => HPL - 2004 |
| 2 |
.\" iwconfig.8 |
| 3 |
.\" |
| 4 |
.TH IWCONFIG 8 "30 March 2006" "wireless-tools" "Linux Programmer's Manual" |
| 5 |
.\" |
| 6 |
.\" NAME part |
| 7 |
.\" |
| 8 |
.SH NAME |
| 9 |
iwconfig \- configure a wireless network interface |
| 10 |
.\" |
| 11 |
.\" SYNOPSIS part |
| 12 |
.\" |
| 13 |
.SH SYNOPSIS |
| 14 |
.BI "iwconfig [" interface ] |
| 15 |
.br |
| 16 |
.BI "iwconfig " interface " [essid " X "] [nwid " N "] [mode " M "] [freq " F "] |
| 17 |
.br |
| 18 |
.BI " [channel " C ] [sens " S "] [ap " A "] [nick " NN ] |
| 19 |
.br |
| 20 |
.BI " [rate " R "] [rts " RT "] [frag " FT "] [txpower " T ] |
| 21 |
.br |
| 22 |
.BI " [enc " E "] [key " K "] [power " P "] [retry " R ] |
| 23 |
.br |
| 24 |
.BI " [modu " M "] [commit] |
| 25 |
.br |
| 26 |
.BI "iwconfig --help" |
| 27 |
.br |
| 28 |
.BI "iwconfig --version" |
| 29 |
.\" |
| 30 |
.\" DESCRIPTION part |
| 31 |
.\" |
| 32 |
.SH DESCRIPTION |
| 33 |
.B Iwconfig |
| 34 |
is similar to |
| 35 |
.IR ifconfig (8), |
| 36 |
but is dedicated to the wireless interfaces. It is used to set the |
| 37 |
parameters of the network interface which are specific to the wireless |
| 38 |
operation (for example : the frequency). |
| 39 |
.B Iwconfig |
| 40 |
may also be used to display those parameters, and the wireless |
| 41 |
statistics (extracted from |
| 42 |
.IR /proc/net/wireless ). |
| 43 |
.PP |
| 44 |
All these parameters and statistics are device dependent. Each driver |
| 45 |
will provide only some of them depending on hardware support, and the |
| 46 |
range of values may change. Please refer to the man page of each |
| 47 |
device for details. |
| 48 |
.\" |
| 49 |
.\" PARAMETER part |
| 50 |
.\" |
| 51 |
.SH PARAMETERS |
| 52 |
.TP |
| 53 |
.B essid |
| 54 |
Set the ESSID (or Network Name - in some products it may also be |
| 55 |
called Domain ID). The ESSID is used to identify cells which are part |
| 56 |
of the same virtual network. |
| 57 |
.br |
| 58 |
As opposed to the AP Address or NWID which define a single cell, the |
| 59 |
ESSID defines a group of cells connected via repeaters or |
| 60 |
infrastructure, where the user may roam transparently. |
| 61 |
.br |
| 62 |
With some cards, you may disable the ESSID checking (ESSID |
| 63 |
promiscuous) with |
| 64 |
.IR off " or " any " (and " on |
| 65 |
to reenable it). |
| 66 |
.br |
| 67 |
If the ESSID of your network is one of the special keywords |
| 68 |
.RI ( off ", " on " or " any ), |
| 69 |
you should use |
| 70 |
.I -- |
| 71 |
to escape it. |
| 72 |
.br |
| 73 |
.B Examples : |
| 74 |
.br |
| 75 |
.I " iwconfig eth0 essid any" |
| 76 |
.br |
| 77 |
.I " iwconfig eth0 essid ""My Network"" |
| 78 |
.br |
| 79 |
.I " iwconfig eth0 essid -- ""ANY"" |
| 80 |
.TP |
| 81 |
.BR nwid |
| 82 |
Set the Network ID. As all adjacent wireless networks share the same |
| 83 |
medium, this parameter is used to differentiate them (create logical |
| 84 |
colocated networks) and identify nodes belonging to the same cell. |
| 85 |
.br |
| 86 |
This parameter is only used for pre-802.11 hardware, the 802.11 |
| 87 |
protocol uses the ESSID and AP Address for this function. |
| 88 |
.br |
| 89 |
With some cards, you may disable the Network ID checking (NWID |
| 90 |
promiscuous) with |
| 91 |
.IR off " (and " on |
| 92 |
to reenable it). |
| 93 |
.br |
| 94 |
.B Examples : |
| 95 |
.br |
| 96 |
.I " iwconfig eth0 nwid AB34 |
| 97 |
.br |
| 98 |
.I " iwconfig eth0 nwid off" |
| 99 |
.TP |
| 100 |
.BR nick [name] |
| 101 |
Set the nickname, or the station name. Some 802.11 products do define |
| 102 |
it, but this is not used as far as the protocols (MAC, IP, TCP) are |
| 103 |
concerned and completely useless as far as configuration goes. Only |
| 104 |
some wireless diagnostic tools may use it. |
| 105 |
.br |
| 106 |
.B Example : |
| 107 |
.br |
| 108 |
.I " iwconfig eth0 nickname ""My Linux Node"" |
| 109 |
.TP |
| 110 |
.B mode |
| 111 |
Set the operating mode of the device, which depends on the network |
| 112 |
topology. The mode can be |
| 113 |
.I Ad-Hoc |
| 114 |
(network composed of only one cell and without Access Point), |
| 115 |
.I Managed |
| 116 |
(node connects to a network composed of many Access Points, with roaming), |
| 117 |
.I Master |
| 118 |
(the node is the synchronisation master or acts as an Access Point), |
| 119 |
.I Repeater |
| 120 |
(the node forwards packets between other wireless nodes), |
| 121 |
.I Secondary |
| 122 |
(the node acts as a backup master/repeater), |
| 123 |
.I Monitor |
| 124 |
(the node is not associated with any cell and passively monitor all |
| 125 |
packets on the frequency) or |
| 126 |
.IR Auto . |
| 127 |
.br |
| 128 |
.B Example : |
| 129 |
.br |
| 130 |
.I " iwconfig eth0 mode Managed" |
| 131 |
.br |
| 132 |
.I " iwconfig eth0 mode Ad-Hoc" |
| 133 |
.TP |
| 134 |
.BR freq / channel |
| 135 |
Set the operating frequency or channel in the device. A value below |
| 136 |
1000 indicates a channel number, a value greater than 1000 is a |
| 137 |
frequency in Hz. You may append the suffix k, M or G to the value (for |
| 138 |
example, "2.46G" for 2.46 GHz frequency), or add enough '0'. |
| 139 |
.br |
| 140 |
Channels are usually numbered starting at 1, and you may use |
| 141 |
.IR iwlist (8) |
| 142 |
to get the total number of channels, list the available frequencies, |
| 143 |
and display the current frequency as a channel. Depending on |
| 144 |
regulations, some frequencies/channels may not be available. |
| 145 |
.br |
| 146 |
When using Managed mode, most often the Access Point dictates the |
| 147 |
channel and the driver may refuse the setting of the frequency. In |
| 148 |
Ad-Hoc mode, the frequency setting may only be used at initial cell |
| 149 |
creation, and may be ignored when joining an existing cell. |
| 150 |
.br |
| 151 |
You may also use |
| 152 |
.I off |
| 153 |
or |
| 154 |
.I auto |
| 155 |
to let the card pick up the best channel (when supported). |
| 156 |
.br |
| 157 |
.B Examples : |
| 158 |
.br |
| 159 |
.I " iwconfig eth0 freq 2422000000" |
| 160 |
.br |
| 161 |
.I " iwconfig eth0 freq 2.422G" |
| 162 |
.br |
| 163 |
.I " iwconfig eth0 channel 3" |
| 164 |
.br |
| 165 |
.I " iwconfig eth0 channel auto" |
| 166 |
.TP |
| 167 |
.B ap |
| 168 |
Force the card to register to the Access Point given by the address, |
| 169 |
if it is possible. This address is the cell identity of the Access |
| 170 |
Point, as reported by wireless scanning, which may be different from |
| 171 |
its network MAC address. If the wireless link is point to point, set |
| 172 |
the address of the other end of the link. If the link is ad-hoc, set |
| 173 |
the cell identity of the ad-hoc network. |
| 174 |
.br |
| 175 |
When the quality of the connection goes too low, the driver may revert |
| 176 |
back to automatic mode (the card selects the best Access Point in |
| 177 |
range). |
| 178 |
.br |
| 179 |
You may also use |
| 180 |
.I off |
| 181 |
to re-enable automatic mode without changing the current Access Point, |
| 182 |
or you may use |
| 183 |
.I any |
| 184 |
or |
| 185 |
.I auto |
| 186 |
to force the card to reassociate with the currently best Access Point. |
| 187 |
.br |
| 188 |
.B Example : |
| 189 |
.br |
| 190 |
.I " iwconfig eth0 ap 00:60:1D:01:23:45" |
| 191 |
.br |
| 192 |
.I " iwconfig eth0 ap any" |
| 193 |
.br |
| 194 |
.I " iwconfig eth0 ap off" |
| 195 |
.TP |
| 196 |
.BR rate / bit [rate] |
| 197 |
For cards supporting multiple bit rates, set the bit-rate in b/s. The |
| 198 |
bit-rate is the speed at which bits are transmitted over the medium, |
| 199 |
the user speed of the link is lower due to medium sharing and |
| 200 |
various overhead. |
| 201 |
.br |
| 202 |
You may append the suffix k, M or G to the value (decimal multiplier : |
| 203 |
10^3, 10^6 and 10^9 b/s), or add enough '0'. Values below 1000 are |
| 204 |
card specific, usually an index in the bit-rate list. Use |
| 205 |
.I auto |
| 206 |
to select automatic bit-rate mode (fallback to lower rate on noisy |
| 207 |
channels), which is the default for most cards, and |
| 208 |
.I fixed |
| 209 |
to revert back to fixed setting. If you specify a bit-rate value and append |
| 210 |
.IR auto , |
| 211 |
the driver will use all bit-rates lower and equal than this value. |
| 212 |
.br |
| 213 |
.B Examples : |
| 214 |
.br |
| 215 |
.I " iwconfig eth0 rate 11M" |
| 216 |
.br |
| 217 |
.I " iwconfig eth0 rate auto" |
| 218 |
.br |
| 219 |
.I " iwconfig eth0 rate 5.5M auto" |
| 220 |
.TP |
| 221 |
.BR txpower |
| 222 |
For cards supporting multiple transmit powers, sets the transmit power |
| 223 |
in dBm. If |
| 224 |
.I W |
| 225 |
is the power in Watt, the power in dBm is |
| 226 |
.IR "P = 30 + 10.log(W)" , |
| 227 |
where log is decimal log. |
| 228 |
If the value is postfixed by |
| 229 |
.IR mW , |
| 230 |
it will be automatically converted to dBm. |
| 231 |
.br |
| 232 |
In addition, |
| 233 |
.IR on " and " off |
| 234 |
enable and disable the radio, and |
| 235 |
.IR auto " and " fixed |
| 236 |
enable and disable power control (if those features are available). |
| 237 |
.br |
| 238 |
.B Examples : |
| 239 |
.br |
| 240 |
.I " iwconfig eth0 txpower 15" |
| 241 |
.br |
| 242 |
.I " iwconfig eth0 txpower 30mW" |
| 243 |
.br |
| 244 |
.I " iwconfig eth0 txpower auto" |
| 245 |
.br |
| 246 |
.I " iwconfig eth0 txpower off" |
| 247 |
.TP |
| 248 |
.B sens |
| 249 |
Set the sensitivity threshold. This define how sensitive is the card |
| 250 |
to poor operating conditions (low signal, interference). Positive |
| 251 |
values are assumed to be the raw value used by the hardware or a |
| 252 |
percentage, negative values are assumed to be dBm. Depending on the |
| 253 |
hardware implementation, this parameter may control various functions. |
| 254 |
.br |
| 255 |
On modern cards, this parameter usually control handover/roaming |
| 256 |
threshold, the lowest signal level for which the hardware remains |
| 257 |
associated with the current Access Point. When the signal level goes |
| 258 |
below this threshold the card starts looking for a new/better Access |
| 259 |
Point. Some cards may use the number of missed beacons to trigger |
| 260 |
this. For high density of Access Points, a higher threshold make sure |
| 261 |
the card is always associated with the best AP, for low density of |
| 262 |
APs, a lower threshold minimise the number of failed handoffs. |
| 263 |
.br |
| 264 |
On more ancient card this parameter usually controls the defer |
| 265 |
threshold, the lowest signal level for which the hardware considers |
| 266 |
the channel busy. Signal levels above this threshold make the hardware |
| 267 |
inhibits its own transmission whereas signals weaker than this are |
| 268 |
ignored and the hardware is free to transmit. This is usually strongly |
| 269 |
linked to the receive threshold, the lowest signal level for which the |
| 270 |
hardware attempts packet reception. Proper setting of these thresholds |
| 271 |
prevent the card to waste time on background noise while still |
| 272 |
receiving weak transmissions. Modern designs seems to control those |
| 273 |
thresholds automatically. |
| 274 |
.br |
| 275 |
.br |
| 276 |
.B Example : |
| 277 |
.br |
| 278 |
.I " iwconfig eth0 sens -80" |
| 279 |
.br |
| 280 |
.I " iwconfig eth0 sens 2" |
| 281 |
.TP |
| 282 |
.BR retry |
| 283 |
Most cards have MAC retransmissions, and some allow to set the |
| 284 |
behaviour of the retry mechanism. |
| 285 |
.br |
| 286 |
To set the maximum number of retries, enter |
| 287 |
.IR "limit `value'" . |
| 288 |
This is an absolute value (without unit), and the default (when |
| 289 |
nothing is specified). |
| 290 |
To set the maximum length of time the MAC should retry, enter |
| 291 |
.IR "lifetime `value'" . |
| 292 |
By defaults, this value is in seconds, append the suffix m or u to |
| 293 |
specify values in milliseconds or microseconds. |
| 294 |
.br |
| 295 |
You can also add the |
| 296 |
.IR short ", " long ", " min " and " max |
| 297 |
modifiers. If the card supports automatic mode, they define the bounds |
| 298 |
of the limit or lifetime. Some other cards define different values |
| 299 |
depending on packet size, for example in 802.11 |
| 300 |
.I min limit |
| 301 |
is the short retry limit (non RTS/CTS packets). |
| 302 |
.br |
| 303 |
.B Examples : |
| 304 |
.br |
| 305 |
.I " iwconfig eth0 retry 16" |
| 306 |
.br |
| 307 |
.I " iwconfig eth0 retry lifetime 300m" |
| 308 |
.br |
| 309 |
.I " iwconfig eth0 retry short 12" |
| 310 |
.br |
| 311 |
.I " iwconfig eth0 retry min limit 8" |
| 312 |
.TP |
| 313 |
.BR rts [_threshold] |
| 314 |
RTS/CTS adds a handshake before each packet transmission to make sure |
| 315 |
that the channel is clear. This adds overhead, but increases |
| 316 |
performance in case of hidden nodes or a large number of active |
| 317 |
nodes. This parameter sets the size of the smallest packet for which |
| 318 |
the node sends RTS ; a value equal to the maximum packet size disables |
| 319 |
the mechanism. You may also set this parameter to |
| 320 |
.IR auto ", " fixed " or " off . |
| 321 |
.br |
| 322 |
.B Examples : |
| 323 |
.br |
| 324 |
.I " iwconfig eth0 rts 250" |
| 325 |
.br |
| 326 |
.I " iwconfig eth0 rts off" |
| 327 |
.TP |
| 328 |
.BR frag [mentation_threshold] |
| 329 |
Fragmentation allows to split an IP packet in a burst of smaller |
| 330 |
fragments transmitted on the medium. In most cases this adds overhead, |
| 331 |
but in a very noisy environment this reduces the error penalty and |
| 332 |
allow packets to get through interference bursts. This parameter sets |
| 333 |
the maximum fragment size which is always lower than the maximum |
| 334 |
packet size. |
| 335 |
.br |
| 336 |
This parameter may also control Frame Bursting available on some |
| 337 |
cards, the ability to send multiple IP packets together. This |
| 338 |
mechanism would be enabled if the fragment size is larger than the |
| 339 |
maximum packet size. |
| 340 |
.br |
| 341 |
You may also set this parameter to |
| 342 |
.IR auto ", " fixed " or " off . |
| 343 |
.br |
| 344 |
.B Examples : |
| 345 |
.br |
| 346 |
.I " iwconfig eth0 frag 512" |
| 347 |
.br |
| 348 |
.I " iwconfig eth0 frag off" |
| 349 |
.TP |
| 350 |
.BR key / enc [ryption] |
| 351 |
Used to manipulate encryption or scrambling keys and security mode. |
| 352 |
.br |
| 353 |
To set the current encryption key, just enter the key in hex digits as |
| 354 |
.IR XXXX-XXXX-XXXX-XXXX " or " XXXXXXXX . |
| 355 |
To set a key other than the current key, prepend or append |
| 356 |
.I [index] |
| 357 |
to the key itself (this won't change which is the active key). You can |
| 358 |
also enter the key as an ASCII string by using the |
| 359 |
.I s: |
| 360 |
prefix. Passphrase is currently not supported. |
| 361 |
.br |
| 362 |
To change which key is the currently active key, just enter |
| 363 |
.I [index] |
| 364 |
(without entering any key value). |
| 365 |
.br |
| 366 |
.IR off " and " on |
| 367 |
disable and reenable encryption. |
| 368 |
.br |
| 369 |
The security mode may be |
| 370 |
.I open |
| 371 |
or |
| 372 |
.IR restricted , |
| 373 |
and its meaning depends on the card used. With most cards, in |
| 374 |
.I open |
| 375 |
mode no authentication is used and the card may also accept |
| 376 |
non-encrypted sessions, whereas in |
| 377 |
.I restricted |
| 378 |
mode only encrypted sessions are accepted and the card will use |
| 379 |
authentication if available. |
| 380 |
.br |
| 381 |
If you need to set multiple keys, or set a key and change the active |
| 382 |
key, you need to use multiple |
| 383 |
.B key |
| 384 |
directives. Arguments can be put in any order, the last one will take |
| 385 |
precedence. |
| 386 |
.br |
| 387 |
.B Examples : |
| 388 |
.br |
| 389 |
.I " iwconfig eth0 key 0123-4567-89" |
| 390 |
.br |
| 391 |
.I " iwconfig eth0 key [3] 0123-4567-89" |
| 392 |
.br |
| 393 |
.I " iwconfig eth0 key s:password [2]" |
| 394 |
.br |
| 395 |
.I " iwconfig eth0 key [2]" |
| 396 |
.br |
| 397 |
.I " iwconfig eth0 key open" |
| 398 |
.br |
| 399 |
.I " iwconfig eth0 key off" |
| 400 |
.br |
| 401 |
.I " iwconfig eth0 key restricted [3] 0123456789" |
| 402 |
.br |
| 403 |
.I " iwconfig eth0 key 01-23 key 45-67 [4] key [4]" |
| 404 |
.TP |
| 405 |
.BR power |
| 406 |
Used to manipulate power management scheme parameters and mode. |
| 407 |
.br |
| 408 |
To set the period between wake ups, enter |
| 409 |
.IR "period `value'" . |
| 410 |
To set the timeout before going back to sleep, enter |
| 411 |
.IR "timeout `value'" . |
| 412 |
To set the generic level of power saving, enter |
| 413 |
.IR "saving `value'" . |
| 414 |
You can also add the |
| 415 |
.IR min " and " max |
| 416 |
modifiers. By default, those values are in seconds, append the suffix |
| 417 |
m or u to specify values in milliseconds or microseconds. Sometimes, |
| 418 |
those values are without units (number of beacon periods, dwell, |
| 419 |
percentage or similar). |
| 420 |
.br |
| 421 |
.IR off " and " on |
| 422 |
disable and reenable power management. Finally, you may set the power |
| 423 |
management mode to |
| 424 |
.I all |
| 425 |
(receive all packets), |
| 426 |
.I unicast |
| 427 |
(receive unicast packets only, discard multicast and broadcast) and |
| 428 |
.I multicast |
| 429 |
(receive multicast and broadcast only, discard unicast packets). |
| 430 |
.br |
| 431 |
.B Examples : |
| 432 |
.br |
| 433 |
.I " iwconfig eth0 power period 2" |
| 434 |
.br |
| 435 |
.I " iwconfig eth0 power 500m unicast" |
| 436 |
.br |
| 437 |
.I " iwconfig eth0 power timeout 300u all" |
| 438 |
.br |
| 439 |
.I " iwconfig eth0 power saving 3" |
| 440 |
.br |
| 441 |
.I " iwconfig eth0 power off" |
| 442 |
.br |
| 443 |
.I " iwconfig eth0 power min period 2 power max period 4" |
| 444 |
.TP |
| 445 |
.BR modu [lation] |
| 446 |
Force the card to use a specific set of modulations. Modern cards |
| 447 |
support various modulations, some which are standard, such as 802.11b |
| 448 |
or 802.11g, and some proprietary. This command force the card to only |
| 449 |
use the specific set of modulations listed on the command line. This |
| 450 |
can be used to fix interoperability issues. |
| 451 |
.br |
| 452 |
The list of available modulations depend on the card/driver and can be |
| 453 |
displayed using |
| 454 |
.IR "iwlist modulation" . |
| 455 |
Note that some card/driver may not be able to select each modulation |
| 456 |
listed independently, some may come as a group. You may also set this |
| 457 |
parameter to |
| 458 |
.IR auto |
| 459 |
let the card/driver do its best. |
| 460 |
.br |
| 461 |
.B Examples : |
| 462 |
.br |
| 463 |
.I " iwconfig eth0 modu 11g" |
| 464 |
.br |
| 465 |
.I " iwconfig eth0 modu CCK OFDMa" |
| 466 |
.br |
| 467 |
.I " iwconfig eth0 modu auto" |
| 468 |
.TP |
| 469 |
.BR commit |
| 470 |
Some cards may not apply changes done through Wireless Extensions |
| 471 |
immediately (they may wait to aggregate the changes or apply it only |
| 472 |
when the card is brought up via |
| 473 |
.IR ifconfig ). |
| 474 |
This command (when available) forces the card to apply all pending |
| 475 |
changes. |
| 476 |
.br |
| 477 |
This is normally not needed, because the card will eventually apply |
| 478 |
the changes, but can be useful for debugging. |
| 479 |
.\" |
| 480 |
.\" DISPLAY part |
| 481 |
.\" |
| 482 |
.SH DISPLAY |
| 483 |
For each device which supports wireless extensions, |
| 484 |
.I iwconfig |
| 485 |
will display the name of the |
| 486 |
.B MAC protocol |
| 487 |
used (name of device for proprietary protocols), the |
| 488 |
.B ESSID |
| 489 |
(Network Name), the |
| 490 |
.BR NWID , |
| 491 |
the |
| 492 |
.B frequency |
| 493 |
(or channel), the |
| 494 |
.BR sensitivity , |
| 495 |
the |
| 496 |
.B mode |
| 497 |
of operation, the |
| 498 |
.B Access Point |
| 499 |
address, the |
| 500 |
.BR bit-rate , |
| 501 |
the |
| 502 |
.BR "RTS threshold" ", the " "fragmentation threshold" , |
| 503 |
the |
| 504 |
.B encryption key |
| 505 |
and the |
| 506 |
.B power management |
| 507 |
settings (depending on availability). |
| 508 |
.PP |
| 509 |
The parameters displayed have the same meaning and values as the |
| 510 |
parameters you can set, please refer to the previous part for a |
| 511 |
detailed explanation of them. |
| 512 |
.br |
| 513 |
Some parameters are only displayed in short/abbreviated form (such as |
| 514 |
encryption). You may use |
| 515 |
.IR iwlist (8) |
| 516 |
to get all the details. |
| 517 |
.br |
| 518 |
Some parameters have two modes (such as bitrate). If the value is |
| 519 |
prefixed by |
| 520 |
.RB ` = ', |
| 521 |
it means that the parameter is fixed and forced to that value, if it |
| 522 |
is prefixed by |
| 523 |
.RB ` : ', |
| 524 |
the parameter is in automatic mode and the current value is shown (and |
| 525 |
may change). |
| 526 |
.TP |
| 527 |
.BR "Access Point" / Cell |
| 528 |
An address equal to 00:00:00:00:00:00 means that the card failed to |
| 529 |
associate with an Access Point (most likely a configuration |
| 530 |
issue). The |
| 531 |
.B Access Point |
| 532 |
parameter will be shown as |
| 533 |
.B Cell |
| 534 |
in ad-hoc mode (for obvious reasons), but otherwise works the same. |
| 535 |
.PP |
| 536 |
If |
| 537 |
.I /proc/net/wireless |
| 538 |
exists, |
| 539 |
.I iwconfig |
| 540 |
will also display its content. Note that those values will depend on |
| 541 |
the driver and the hardware specifics, so you need to refer to your |
| 542 |
driver documentation for proper interpretation of those values. |
| 543 |
.TP |
| 544 |
.B Link quality |
| 545 |
Overall quality of the link. May be based on the level of contention |
| 546 |
or interference, the bit or frame error rate, how good the received |
| 547 |
signal is, some timing synchronisation, or other hardware metric. This |
| 548 |
is an aggregate value, and depends totally on the driver and hardware. |
| 549 |
.TP |
| 550 |
.B Signal level |
| 551 |
Received signal strength (RSSI - how strong the received signal |
| 552 |
is). May be arbitrary units or dBm, |
| 553 |
.I iwconfig |
| 554 |
uses driver meta information to interpret the raw value given by |
| 555 |
.I /proc/net/wireless |
| 556 |
and display the proper unit or maximum value (using 8 bit arithmetic). In |
| 557 |
.I Ad-Hoc |
| 558 |
mode, this may be undefined and you should use |
| 559 |
.IR iwspy . |
| 560 |
.TP |
| 561 |
.B Noise level |
| 562 |
Background noise level (when no packet is transmitted). Similar |
| 563 |
comments as for |
| 564 |
.BR "Signal level" . |
| 565 |
.TP |
| 566 |
.B Rx invalid nwid |
| 567 |
Number of packets received with a different NWID or ESSID. Used to |
| 568 |
detect configuration problems or adjacent network existence (on the |
| 569 |
same frequency). |
| 570 |
.TP |
| 571 |
.B Rx invalid crypt |
| 572 |
Number of packets that the hardware was unable to decrypt. This can be |
| 573 |
used to detect invalid encryption settings. |
| 574 |
.TP |
| 575 |
.B Rx invalid frag |
| 576 |
Number of packets for which the hardware was not able to properly |
| 577 |
re-assemble the link layer fragments (most likely one was missing). |
| 578 |
.TP |
| 579 |
.B Tx excessive retries |
| 580 |
Number of packets that the hardware failed to deliver. Most MAC |
| 581 |
protocols will retry the packet a number of times before giving up. |
| 582 |
.TP |
| 583 |
.B Invalid misc |
| 584 |
Other packets lost in relation with specific wireless operations. |
| 585 |
.TP |
| 586 |
.B Missed beacon |
| 587 |
Number of periodic beacons from the Cell or the Access Point we have |
| 588 |
missed. Beacons are sent at regular intervals to maintain the cell |
| 589 |
coordination, failure to receive them usually indicates that the card |
| 590 |
is out of range. |
| 591 |
.\" |
| 592 |
.\" AUTHOR part |
| 593 |
.\" |
| 594 |
.SH AUTHOR |
| 595 |
Jean Tourrilhes \- [email protected] |
| 596 |
.\" |
| 597 |
.\" FILES part |
| 598 |
.\" |
| 599 |
.SH FILES |
| 600 |
.I /proc/net/wireless |
| 601 |
.\" |
| 602 |
.\" SEE ALSO part |
| 603 |
.\" |
| 604 |
.SH SEE ALSO |
| 605 |
.BR ifconfig (8), |
| 606 |
.BR iwspy (8), |
| 607 |
.BR iwlist (8), |
| 608 |
.BR iwevent (8), |
| 609 |
.BR iwpriv (8), |
| 610 |
.BR wireless (7) |
| 611 |
.BR ifrename (8), |
| 612 |
.BR iftab (5), |
| 613 |
.BR iwgetid (8). |