| 1 |
# SPDX-License-Identifier: GPL-2.0-only |
| 2 |
# |
| 3 |
# Arcnet configuration |
| 4 |
# |
| 5 |
|
| 6 |
menuconfig ARCNET |
| 7 |
depends on NETDEVICES && (ISA || PCI || PCMCIA) && HAS_IOPORT |
| 8 |
tristate "ARCnet support" |
| 9 |
help |
| 10 |
If you have a network card of this type, say Y and check out the |
| 11 |
(arguably) beautiful poetry in |
| 12 |
<file:Documentation/networking/arcnet.rst>. |
| 13 |
|
| 14 |
You need both this driver, and the driver for the particular ARCnet |
| 15 |
chipset of your card. If you don't know, then it's probably a |
| 16 |
COM90xx type card, so say Y (or M) to "ARCnet COM90xx chipset |
| 17 |
support" below. |
| 18 |
|
| 19 |
To compile this driver as a module, choose M here. The module will |
| 20 |
be called arcnet. |
| 21 |
|
| 22 |
if ARCNET |
| 23 |
|
| 24 |
config ARCNET_1201 |
| 25 |
tristate "Enable standard ARCNet packet format (RFC 1201)" |
| 26 |
help |
| 27 |
This allows you to use RFC1201 with your ARCnet card via the virtual |
| 28 |
arc0 device. You need to say Y here to communicate with |
| 29 |
industry-standard RFC1201 implementations, like the arcether.com |
| 30 |
packet driver or most DOS/Windows ODI drivers. Please read the |
| 31 |
ARCnet documentation in <file:Documentation/networking/arcnet.rst> |
| 32 |
for more information about using arc0. |
| 33 |
|
| 34 |
config ARCNET_1051 |
| 35 |
tristate "Enable old ARCNet packet format (RFC 1051)" |
| 36 |
help |
| 37 |
This allows you to use RFC1051 with your ARCnet card via the virtual |
| 38 |
arc0s device. You only need arc0s if you want to talk to ARCnet |
| 39 |
software complying with the "old" standard, specifically, the DOS |
| 40 |
arcnet.com packet driver, Amigas running AmiTCP, and some variants |
| 41 |
of NetBSD. You do not need to say Y here to communicate with |
| 42 |
industry-standard RFC1201 implementations, like the arcether.com |
| 43 |
packet driver or most DOS/Windows ODI drivers. RFC1201 is included |
| 44 |
automatically as the arc0 device. Please read the ARCnet |
| 45 |
documentation in <file:Documentation/networking/arcnet.rst> for more |
| 46 |
information about using arc0e and arc0s. |
| 47 |
|
| 48 |
config ARCNET_RAW |
| 49 |
tristate "Enable raw mode packet interface" |
| 50 |
help |
| 51 |
ARCnet "raw mode" packet encapsulation, no soft headers. Unlikely |
| 52 |
to work unless talking to a copy of the same Linux arcnet driver, |
| 53 |
but perhaps marginally faster in that case. |
| 54 |
|
| 55 |
config ARCNET_CAP |
| 56 |
tristate "Enable CAP mode packet interface" |
| 57 |
help |
| 58 |
ARCnet "cap mode" packet encapsulation. Used to get the hardware |
| 59 |
acknowledge back to userspace. After the initial protocol byte every |
| 60 |
packet is stuffed with an extra 4 byte "cookie" which doesn't |
| 61 |
actually appear on the network. After transmit the driver will send |
| 62 |
back a packet with protocol byte 0 containing the status of the |
| 63 |
transmission: |
| 64 |
0=no hardware acknowledge |
| 65 |
1=excessive nak |
| 66 |
2=transmission accepted by the receiver hardware |
| 67 |
|
| 68 |
Received packets are also stuffed with the extra 4 bytes but it will |
| 69 |
be random data. |
| 70 |
|
| 71 |
Cap only listens to protocol 1-8. |
| 72 |
|
| 73 |
config ARCNET_COM90xx |
| 74 |
tristate "ARCnet COM90xx (normal) chipset driver" |
| 75 |
help |
| 76 |
This is the chipset driver for the standard COM90xx cards. If you |
| 77 |
have always used the old ARCnet driver without knowing what type of |
| 78 |
card you had, this is probably the one for you. |
| 79 |
|
| 80 |
To compile this driver as a module, choose M here. The module will |
| 81 |
be called com90xx. |
| 82 |
|
| 83 |
config ARCNET_COM90xxIO |
| 84 |
tristate "ARCnet COM90xx (IO mapped) chipset driver" |
| 85 |
help |
| 86 |
This is the chipset driver for the COM90xx cards, using them in |
| 87 |
IO-mapped mode instead of memory-mapped mode. This is slower than |
| 88 |
the normal driver. Only use it if your card doesn't support shared |
| 89 |
memory. |
| 90 |
|
| 91 |
To compile this driver as a module, choose M here. The module will |
| 92 |
be called com90io. |
| 93 |
|
| 94 |
config ARCNET_RIM_I |
| 95 |
tristate "ARCnet COM90xx (RIM I) chipset driver" |
| 96 |
help |
| 97 |
This is yet another chipset driver for the COM90xx cards, but this |
| 98 |
time only using memory-mapped mode, and no IO ports at all. This |
| 99 |
driver is completely untested, so if you have one of these cards, |
| 100 |
please mail <[email protected]>, especially if it works! |
| 101 |
|
| 102 |
To compile this driver as a module, choose M here. The module will |
| 103 |
be called arc-rimi. |
| 104 |
|
| 105 |
config ARCNET_COM20020 |
| 106 |
tristate "ARCnet COM20020 chipset driver" |
| 107 |
depends on LEDS_CLASS |
| 108 |
help |
| 109 |
This is the driver for the new COM20020 chipset. It supports such |
| 110 |
things as promiscuous mode, so packet sniffing is possible, and |
| 111 |
extra diagnostic information. |
| 112 |
|
| 113 |
To compile this driver as a module, choose M here. The module will |
| 114 |
be called com20020. |
| 115 |
|
| 116 |
config ARCNET_COM20020_ISA |
| 117 |
tristate "Support for COM20020 on ISA" |
| 118 |
depends on ARCNET_COM20020 && ISA |
| 119 |
|
| 120 |
config ARCNET_COM20020_PCI |
| 121 |
tristate "Support for COM20020 on PCI" |
| 122 |
depends on ARCNET_COM20020 && PCI |
| 123 |
|
| 124 |
config ARCNET_COM20020_CS |
| 125 |
tristate "COM20020 ARCnet PCMCIA support" |
| 126 |
depends on ARCNET_COM20020 && PCMCIA |
| 127 |
help |
| 128 |
Say Y here if you intend to attach this type of ARCnet PCMCIA card |
| 129 |
to your computer. |
| 130 |
|
| 131 |
To compile this driver as a module, choose M here: the module will be |
| 132 |
called com20020_cs. If unsure, say N. |
| 133 |
|
| 134 |
endif # ARCNET |