| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Alchemy Db1550/Pb1550 board support |
| 4 |
* |
| 5 |
* (c) 2011 Manuel Lauss <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
#include <linux/clk.h> |
| 9 |
#include <linux/dma-mapping.h> |
| 10 |
#include <linux/gpio.h> |
| 11 |
#include <linux/i2c.h> |
| 12 |
#include <linux/init.h> |
| 13 |
#include <linux/io.h> |
| 14 |
#include <linux/interrupt.h> |
| 15 |
#include <linux/mtd/mtd.h> |
| 16 |
#include <linux/mtd/platnand.h> |
| 17 |
#include <linux/platform_device.h> |
| 18 |
#include <linux/pm.h> |
| 19 |
#include <linux/spi/spi.h> |
| 20 |
#include <linux/spi/flash.h> |
| 21 |
#include <asm/bootinfo.h> |
| 22 |
#include <asm/mach-au1x00/au1000.h> |
| 23 |
#include <asm/mach-au1x00/gpio-au1000.h> |
| 24 |
#include <asm/mach-au1x00/au1xxx_eth.h> |
| 25 |
#include <asm/mach-au1x00/au1xxx_dbdma.h> |
| 26 |
#include <asm/mach-au1x00/au1xxx_psc.h> |
| 27 |
#include <asm/mach-au1x00/au1550_spi.h> |
| 28 |
#include <asm/mach-au1x00/au1550nd.h> |
| 29 |
#include <asm/mach-db1x00/bcsr.h> |
| 30 |
#include <prom.h> |
| 31 |
#include "platform.h" |
| 32 |
|
| 33 |
static void __init db1550_hw_setup(void) |
| 34 |
{ |
| 35 |
void __iomem *base; |
| 36 |
unsigned long v; |
| 37 |
|
| 38 |
/* complete pin setup: assign GPIO16 to PSC0_SYNC1 (SPI cs# line) |
| 39 |
* as well as PSC1_SYNC for AC97 on PB1550. |
| 40 |
*/ |
| 41 |
v = alchemy_rdsys(AU1000_SYS_PINFUNC); |
| 42 |
alchemy_wrsys(v | 1 | SYS_PF_PSC1_S1, AU1000_SYS_PINFUNC); |
| 43 |
|
| 44 |
/* reset the AC97 codec now, the reset time in the psc-ac97 driver |
| 45 |
* is apparently too short although it's ridiculous as it is. |
| 46 |
*/ |
| 47 |
base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR); |
| 48 |
__raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE, |
| 49 |
base + PSC_SEL_OFFSET); |
| 50 |
__raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET); |
| 51 |
wmb(); |
| 52 |
__raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET); |
| 53 |
wmb(); |
| 54 |
} |
| 55 |
|
| 56 |
int __init db1550_board_setup(void) |
| 57 |
{ |
| 58 |
unsigned short whoami; |
| 59 |
|
| 60 |
bcsr_init(DB1550_BCSR_PHYS_ADDR, |
| 61 |
DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS); |
| 62 |
|
| 63 |
whoami = bcsr_read(BCSR_WHOAMI); /* PB1550 hexled offset differs */ |
| 64 |
switch (BCSR_WHOAMI_BOARD(whoami)) { |
| 65 |
case BCSR_WHOAMI_PB1550_SDR: |
| 66 |
case BCSR_WHOAMI_PB1550_DDR: |
| 67 |
bcsr_init(PB1550_BCSR_PHYS_ADDR, |
| 68 |
PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS); |
| 69 |
break; |
| 70 |
case BCSR_WHOAMI_DB1550: |
| 71 |
break; |
| 72 |
default: |
| 73 |
return -ENODEV; |
| 74 |
} |
| 75 |
|
| 76 |
pr_info("Alchemy/AMD %s Board, CPLD Rev %d Board-ID %d " \ |
| 77 |
"Daughtercard ID %d\n", get_system_type(), |
| 78 |
(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf); |
| 79 |
|
| 80 |
db1550_hw_setup(); |
| 81 |
return 0; |
| 82 |
} |
| 83 |
|
| 84 |
/*****************************************************************************/ |
| 85 |
|
| 86 |
static u64 au1550_all_dmamask = DMA_BIT_MASK(32); |
| 87 |
|
| 88 |
static struct mtd_partition db1550_spiflash_parts[] = { |
| 89 |
{ |
| 90 |
.name = "spi_flash", |
| 91 |
.offset = 0, |
| 92 |
.size = MTDPART_SIZ_FULL, |
| 93 |
}, |
| 94 |
}; |
| 95 |
|
| 96 |
static struct flash_platform_data db1550_spiflash_data = { |
| 97 |
.name = "s25fl010", |
| 98 |
.parts = db1550_spiflash_parts, |
| 99 |
.nr_parts = ARRAY_SIZE(db1550_spiflash_parts), |
| 100 |
.type = "m25p10", |
| 101 |
}; |
| 102 |
|
| 103 |
static struct spi_board_info db1550_spi_devs[] __initdata = { |
| 104 |
{ |
| 105 |
/* TI TMP121AIDBVR temp sensor */ |
| 106 |
.modalias = "tmp121", |
| 107 |
.max_speed_hz = 2400000, |
| 108 |
.bus_num = 0, |
| 109 |
.chip_select = 0, |
| 110 |
.mode = SPI_MODE_0, |
| 111 |
}, |
| 112 |
{ |
| 113 |
/* Spansion S25FL001D0FMA SPI flash */ |
| 114 |
.modalias = "m25p80", |
| 115 |
.max_speed_hz = 2400000, |
| 116 |
.bus_num = 0, |
| 117 |
.chip_select = 1, |
| 118 |
.mode = SPI_MODE_0, |
| 119 |
.platform_data = &db1550_spiflash_data, |
| 120 |
}, |
| 121 |
}; |
| 122 |
|
| 123 |
static struct i2c_board_info db1550_i2c_devs[] __initdata = { |
| 124 |
{ I2C_BOARD_INFO("24c04", 0x52),}, /* AT24C04-10 I2C eeprom */ |
| 125 |
{ I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */ |
| 126 |
{ I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */ |
| 127 |
}; |
| 128 |
|
| 129 |
/**********************************************************************/ |
| 130 |
|
| 131 |
static void au1550_nand_cmd_ctrl(struct nand_chip *this, int cmd, |
| 132 |
unsigned int ctrl) |
| 133 |
{ |
| 134 |
unsigned long ioaddr = (unsigned long)this->legacy.IO_ADDR_W; |
| 135 |
|
| 136 |
ioaddr &= 0xffffff00; |
| 137 |
|
| 138 |
if (ctrl & NAND_CLE) { |
| 139 |
ioaddr += MEM_STNAND_CMD; |
| 140 |
} else if (ctrl & NAND_ALE) { |
| 141 |
ioaddr += MEM_STNAND_ADDR; |
| 142 |
} else { |
| 143 |
/* assume we want to r/w real data by default */ |
| 144 |
ioaddr += MEM_STNAND_DATA; |
| 145 |
} |
| 146 |
this->legacy.IO_ADDR_R = this->legacy.IO_ADDR_W = (void __iomem *)ioaddr; |
| 147 |
if (cmd != NAND_CMD_NONE) { |
| 148 |
__raw_writeb(cmd, this->legacy.IO_ADDR_W); |
| 149 |
wmb(); |
| 150 |
} |
| 151 |
} |
| 152 |
|
| 153 |
static int au1550_nand_device_ready(struct nand_chip *this) |
| 154 |
{ |
| 155 |
return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1; |
| 156 |
} |
| 157 |
|
| 158 |
static struct mtd_partition db1550_nand_parts[] = { |
| 159 |
{ |
| 160 |
.name = "NAND FS 0", |
| 161 |
.offset = 0, |
| 162 |
.size = 8 * 1024 * 1024, |
| 163 |
}, |
| 164 |
{ |
| 165 |
.name = "NAND FS 1", |
| 166 |
.offset = MTDPART_OFS_APPEND, |
| 167 |
.size = MTDPART_SIZ_FULL |
| 168 |
}, |
| 169 |
}; |
| 170 |
|
| 171 |
struct platform_nand_data db1550_nand_platdata = { |
| 172 |
.chip = { |
| 173 |
.nr_chips = 1, |
| 174 |
.chip_offset = 0, |
| 175 |
.nr_partitions = ARRAY_SIZE(db1550_nand_parts), |
| 176 |
.partitions = db1550_nand_parts, |
| 177 |
.chip_delay = 20, |
| 178 |
}, |
| 179 |
.ctrl = { |
| 180 |
.dev_ready = au1550_nand_device_ready, |
| 181 |
.cmd_ctrl = au1550_nand_cmd_ctrl, |
| 182 |
}, |
| 183 |
}; |
| 184 |
|
| 185 |
static struct resource db1550_nand_res[] = { |
| 186 |
[0] = { |
| 187 |
.start = 0x20000000, |
| 188 |
.end = 0x200000ff, |
| 189 |
.flags = IORESOURCE_MEM, |
| 190 |
}, |
| 191 |
}; |
| 192 |
|
| 193 |
static struct platform_device db1550_nand_dev = { |
| 194 |
.name = "gen_nand", |
| 195 |
.num_resources = ARRAY_SIZE(db1550_nand_res), |
| 196 |
.resource = db1550_nand_res, |
| 197 |
.id = -1, |
| 198 |
.dev = { |
| 199 |
.platform_data = &db1550_nand_platdata, |
| 200 |
} |
| 201 |
}; |
| 202 |
|
| 203 |
static struct au1550nd_platdata pb1550_nand_pd = { |
| 204 |
.parts = db1550_nand_parts, |
| 205 |
.num_parts = ARRAY_SIZE(db1550_nand_parts), |
| 206 |
.devwidth = 0, /* x8 NAND default, needs fixing up */ |
| 207 |
}; |
| 208 |
|
| 209 |
static struct platform_device pb1550_nand_dev = { |
| 210 |
.name = "au1550-nand", |
| 211 |
.id = -1, |
| 212 |
.resource = db1550_nand_res, |
| 213 |
.num_resources = ARRAY_SIZE(db1550_nand_res), |
| 214 |
.dev = { |
| 215 |
.platform_data = &pb1550_nand_pd, |
| 216 |
}, |
| 217 |
}; |
| 218 |
|
| 219 |
static void __init pb1550_nand_setup(void) |
| 220 |
{ |
| 221 |
int boot_swapboot = (alchemy_rdsmem(AU1000_MEM_STSTAT) & (0x7 << 1)) | |
| 222 |
((bcsr_read(BCSR_STATUS) >> 6) & 0x1); |
| 223 |
|
| 224 |
gpio_direction_input(206); /* de-assert NAND CS# */ |
| 225 |
switch (boot_swapboot) { |
| 226 |
case 0: case 2: case 8: case 0xC: case 0xD: |
| 227 |
/* x16 NAND Flash */ |
| 228 |
pb1550_nand_pd.devwidth = 1; |
| 229 |
fallthrough; |
| 230 |
case 1: case 3: case 9: case 0xE: case 0xF: |
| 231 |
/* x8 NAND, already set up */ |
| 232 |
platform_device_register(&pb1550_nand_dev); |
| 233 |
} |
| 234 |
} |
| 235 |
|
| 236 |
/**********************************************************************/ |
| 237 |
|
| 238 |
static struct resource au1550_psc0_res[] = { |
| 239 |
[0] = { |
| 240 |
.start = AU1550_PSC0_PHYS_ADDR, |
| 241 |
.end = AU1550_PSC0_PHYS_ADDR + 0xfff, |
| 242 |
.flags = IORESOURCE_MEM, |
| 243 |
}, |
| 244 |
[1] = { |
| 245 |
.start = AU1550_PSC0_INT, |
| 246 |
.end = AU1550_PSC0_INT, |
| 247 |
.flags = IORESOURCE_IRQ, |
| 248 |
}, |
| 249 |
[2] = { |
| 250 |
.start = AU1550_DSCR_CMD0_PSC0_TX, |
| 251 |
.end = AU1550_DSCR_CMD0_PSC0_TX, |
| 252 |
.flags = IORESOURCE_DMA, |
| 253 |
}, |
| 254 |
[3] = { |
| 255 |
.start = AU1550_DSCR_CMD0_PSC0_RX, |
| 256 |
.end = AU1550_DSCR_CMD0_PSC0_RX, |
| 257 |
.flags = IORESOURCE_DMA, |
| 258 |
}, |
| 259 |
}; |
| 260 |
|
| 261 |
static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol) |
| 262 |
{ |
| 263 |
if (cs) |
| 264 |
bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL); |
| 265 |
else |
| 266 |
bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0); |
| 267 |
} |
| 268 |
|
| 269 |
static struct au1550_spi_info db1550_spi_platdata = { |
| 270 |
.mainclk_hz = 48000000, /* PSC0 clock: max. 2.4MHz SPI clk */ |
| 271 |
.num_chipselect = 2, |
| 272 |
.activate_cs = db1550_spi_cs_en, |
| 273 |
}; |
| 274 |
|
| 275 |
|
| 276 |
static struct platform_device db1550_spi_dev = { |
| 277 |
.dev = { |
| 278 |
.dma_mask = &au1550_all_dmamask, |
| 279 |
.coherent_dma_mask = DMA_BIT_MASK(32), |
| 280 |
.platform_data = &db1550_spi_platdata, |
| 281 |
}, |
| 282 |
.name = "au1550-spi", |
| 283 |
.id = 0, /* bus number */ |
| 284 |
.num_resources = ARRAY_SIZE(au1550_psc0_res), |
| 285 |
.resource = au1550_psc0_res, |
| 286 |
}; |
| 287 |
|
| 288 |
/**********************************************************************/ |
| 289 |
|
| 290 |
static struct resource au1550_psc1_res[] = { |
| 291 |
[0] = { |
| 292 |
.start = AU1550_PSC1_PHYS_ADDR, |
| 293 |
.end = AU1550_PSC1_PHYS_ADDR + 0xfff, |
| 294 |
.flags = IORESOURCE_MEM, |
| 295 |
}, |
| 296 |
[1] = { |
| 297 |
.start = AU1550_PSC1_INT, |
| 298 |
.end = AU1550_PSC1_INT, |
| 299 |
.flags = IORESOURCE_IRQ, |
| 300 |
}, |
| 301 |
[2] = { |
| 302 |
.start = AU1550_DSCR_CMD0_PSC1_TX, |
| 303 |
.end = AU1550_DSCR_CMD0_PSC1_TX, |
| 304 |
.flags = IORESOURCE_DMA, |
| 305 |
}, |
| 306 |
[3] = { |
| 307 |
.start = AU1550_DSCR_CMD0_PSC1_RX, |
| 308 |
.end = AU1550_DSCR_CMD0_PSC1_RX, |
| 309 |
.flags = IORESOURCE_DMA, |
| 310 |
}, |
| 311 |
}; |
| 312 |
|
| 313 |
static struct platform_device db1550_ac97_dev = { |
| 314 |
.name = "au1xpsc_ac97", |
| 315 |
.id = 1, /* PSC ID */ |
| 316 |
.num_resources = ARRAY_SIZE(au1550_psc1_res), |
| 317 |
.resource = au1550_psc1_res, |
| 318 |
}; |
| 319 |
|
| 320 |
|
| 321 |
static struct resource au1550_psc2_res[] = { |
| 322 |
[0] = { |
| 323 |
.start = AU1550_PSC2_PHYS_ADDR, |
| 324 |
.end = AU1550_PSC2_PHYS_ADDR + 0xfff, |
| 325 |
.flags = IORESOURCE_MEM, |
| 326 |
}, |
| 327 |
[1] = { |
| 328 |
.start = AU1550_PSC2_INT, |
| 329 |
.end = AU1550_PSC2_INT, |
| 330 |
.flags = IORESOURCE_IRQ, |
| 331 |
}, |
| 332 |
[2] = { |
| 333 |
.start = AU1550_DSCR_CMD0_PSC2_TX, |
| 334 |
.end = AU1550_DSCR_CMD0_PSC2_TX, |
| 335 |
.flags = IORESOURCE_DMA, |
| 336 |
}, |
| 337 |
[3] = { |
| 338 |
.start = AU1550_DSCR_CMD0_PSC2_RX, |
| 339 |
.end = AU1550_DSCR_CMD0_PSC2_RX, |
| 340 |
.flags = IORESOURCE_DMA, |
| 341 |
}, |
| 342 |
}; |
| 343 |
|
| 344 |
static struct platform_device db1550_i2c_dev = { |
| 345 |
.name = "au1xpsc_smbus", |
| 346 |
.id = 0, /* bus number */ |
| 347 |
.num_resources = ARRAY_SIZE(au1550_psc2_res), |
| 348 |
.resource = au1550_psc2_res, |
| 349 |
}; |
| 350 |
|
| 351 |
/**********************************************************************/ |
| 352 |
|
| 353 |
static struct resource au1550_psc3_res[] = { |
| 354 |
[0] = { |
| 355 |
.start = AU1550_PSC3_PHYS_ADDR, |
| 356 |
.end = AU1550_PSC3_PHYS_ADDR + 0xfff, |
| 357 |
.flags = IORESOURCE_MEM, |
| 358 |
}, |
| 359 |
[1] = { |
| 360 |
.start = AU1550_PSC3_INT, |
| 361 |
.end = AU1550_PSC3_INT, |
| 362 |
.flags = IORESOURCE_IRQ, |
| 363 |
}, |
| 364 |
[2] = { |
| 365 |
.start = AU1550_DSCR_CMD0_PSC3_TX, |
| 366 |
.end = AU1550_DSCR_CMD0_PSC3_TX, |
| 367 |
.flags = IORESOURCE_DMA, |
| 368 |
}, |
| 369 |
[3] = { |
| 370 |
.start = AU1550_DSCR_CMD0_PSC3_RX, |
| 371 |
.end = AU1550_DSCR_CMD0_PSC3_RX, |
| 372 |
.flags = IORESOURCE_DMA, |
| 373 |
}, |
| 374 |
}; |
| 375 |
|
| 376 |
static struct platform_device db1550_i2s_dev = { |
| 377 |
.name = "au1xpsc_i2s", |
| 378 |
.id = 3, /* PSC ID */ |
| 379 |
.num_resources = ARRAY_SIZE(au1550_psc3_res), |
| 380 |
.resource = au1550_psc3_res, |
| 381 |
}; |
| 382 |
|
| 383 |
/**********************************************************************/ |
| 384 |
|
| 385 |
static struct platform_device db1550_stac_dev = { |
| 386 |
.name = "ac97-codec", |
| 387 |
.id = 1, /* on PSC1 */ |
| 388 |
}; |
| 389 |
|
| 390 |
static struct platform_device db1550_ac97dma_dev = { |
| 391 |
.name = "au1xpsc-pcm", |
| 392 |
.id = 1, /* on PSC3 */ |
| 393 |
}; |
| 394 |
|
| 395 |
static struct platform_device db1550_i2sdma_dev = { |
| 396 |
.name = "au1xpsc-pcm", |
| 397 |
.id = 3, /* on PSC3 */ |
| 398 |
}; |
| 399 |
|
| 400 |
static struct platform_device db1550_sndac97_dev = { |
| 401 |
.name = "db1550-ac97", |
| 402 |
.dev = { |
| 403 |
.dma_mask = &au1550_all_dmamask, |
| 404 |
.coherent_dma_mask = DMA_BIT_MASK(32), |
| 405 |
}, |
| 406 |
}; |
| 407 |
|
| 408 |
static struct platform_device db1550_sndi2s_dev = { |
| 409 |
.name = "db1550-i2s", |
| 410 |
.dev = { |
| 411 |
.dma_mask = &au1550_all_dmamask, |
| 412 |
.coherent_dma_mask = DMA_BIT_MASK(32), |
| 413 |
}, |
| 414 |
}; |
| 415 |
|
| 416 |
/**********************************************************************/ |
| 417 |
|
| 418 |
static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin) |
| 419 |
{ |
| 420 |
if ((slot < 11) || (slot > 13) || pin == 0) |
| 421 |
return -1; |
| 422 |
if (slot == 11) |
| 423 |
return (pin == 1) ? AU1550_PCI_INTC : 0xff; |
| 424 |
if (slot == 12) { |
| 425 |
switch (pin) { |
| 426 |
case 1: return AU1550_PCI_INTB; |
| 427 |
case 2: return AU1550_PCI_INTC; |
| 428 |
case 3: return AU1550_PCI_INTD; |
| 429 |
case 4: return AU1550_PCI_INTA; |
| 430 |
} |
| 431 |
} |
| 432 |
if (slot == 13) { |
| 433 |
switch (pin) { |
| 434 |
case 1: return AU1550_PCI_INTA; |
| 435 |
case 2: return AU1550_PCI_INTB; |
| 436 |
case 3: return AU1550_PCI_INTC; |
| 437 |
case 4: return AU1550_PCI_INTD; |
| 438 |
} |
| 439 |
} |
| 440 |
return -1; |
| 441 |
} |
| 442 |
|
| 443 |
static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin) |
| 444 |
{ |
| 445 |
if ((slot < 12) || (slot > 13) || pin == 0) |
| 446 |
return -1; |
| 447 |
if (slot == 12) { |
| 448 |
switch (pin) { |
| 449 |
case 1: return AU1500_PCI_INTB; |
| 450 |
case 2: return AU1500_PCI_INTC; |
| 451 |
case 3: return AU1500_PCI_INTD; |
| 452 |
case 4: return AU1500_PCI_INTA; |
| 453 |
} |
| 454 |
} |
| 455 |
if (slot == 13) { |
| 456 |
switch (pin) { |
| 457 |
case 1: return AU1500_PCI_INTA; |
| 458 |
case 2: return AU1500_PCI_INTB; |
| 459 |
case 3: return AU1500_PCI_INTC; |
| 460 |
case 4: return AU1500_PCI_INTD; |
| 461 |
} |
| 462 |
} |
| 463 |
return -1; |
| 464 |
} |
| 465 |
|
| 466 |
static struct resource alchemy_pci_host_res[] = { |
| 467 |
[0] = { |
| 468 |
.start = AU1500_PCI_PHYS_ADDR, |
| 469 |
.end = AU1500_PCI_PHYS_ADDR + 0xfff, |
| 470 |
.flags = IORESOURCE_MEM, |
| 471 |
}, |
| 472 |
}; |
| 473 |
|
| 474 |
static struct alchemy_pci_platdata db1550_pci_pd = { |
| 475 |
.board_map_irq = db1550_map_pci_irq, |
| 476 |
}; |
| 477 |
|
| 478 |
static struct platform_device db1550_pci_host_dev = { |
| 479 |
.dev.platform_data = &db1550_pci_pd, |
| 480 |
.name = "alchemy-pci", |
| 481 |
.id = 0, |
| 482 |
.num_resources = ARRAY_SIZE(alchemy_pci_host_res), |
| 483 |
.resource = alchemy_pci_host_res, |
| 484 |
}; |
| 485 |
|
| 486 |
/**********************************************************************/ |
| 487 |
|
| 488 |
static struct platform_device *db1550_devs[] __initdata = { |
| 489 |
&db1550_i2c_dev, |
| 490 |
&db1550_ac97_dev, |
| 491 |
&db1550_spi_dev, |
| 492 |
&db1550_i2s_dev, |
| 493 |
&db1550_stac_dev, |
| 494 |
&db1550_ac97dma_dev, |
| 495 |
&db1550_i2sdma_dev, |
| 496 |
&db1550_sndac97_dev, |
| 497 |
&db1550_sndi2s_dev, |
| 498 |
}; |
| 499 |
|
| 500 |
/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */ |
| 501 |
int __init db1550_pci_setup(int id) |
| 502 |
{ |
| 503 |
if (id) |
| 504 |
db1550_pci_pd.board_map_irq = pb1550_map_pci_irq; |
| 505 |
return platform_device_register(&db1550_pci_host_dev); |
| 506 |
} |
| 507 |
|
| 508 |
static void __init db1550_devices(void) |
| 509 |
{ |
| 510 |
alchemy_gpio_direction_output(203, 0); /* red led on */ |
| 511 |
|
| 512 |
irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH); /* CD0# */ |
| 513 |
irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH); /* CD1# */ |
| 514 |
irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW); /* CARD0# */ |
| 515 |
irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW); /* CARD1# */ |
| 516 |
irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */ |
| 517 |
irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */ |
| 518 |
|
| 519 |
db1x_register_pcmcia_socket( |
| 520 |
AU1000_PCMCIA_ATTR_PHYS_ADDR, |
| 521 |
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1, |
| 522 |
AU1000_PCMCIA_MEM_PHYS_ADDR, |
| 523 |
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1, |
| 524 |
AU1000_PCMCIA_IO_PHYS_ADDR, |
| 525 |
AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1, |
| 526 |
AU1550_GPIO3_INT, 0, |
| 527 |
/*AU1550_GPIO21_INT*/0, 0, 0); |
| 528 |
|
| 529 |
db1x_register_pcmcia_socket( |
| 530 |
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000, |
| 531 |
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1, |
| 532 |
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000, |
| 533 |
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1, |
| 534 |
AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000, |
| 535 |
AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1, |
| 536 |
AU1550_GPIO5_INT, 1, |
| 537 |
/*AU1550_GPIO22_INT*/0, 0, 1); |
| 538 |
|
| 539 |
platform_device_register(&db1550_nand_dev); |
| 540 |
|
| 541 |
alchemy_gpio_direction_output(202, 0); /* green led on */ |
| 542 |
} |
| 543 |
|
| 544 |
static void __init pb1550_devices(void) |
| 545 |
{ |
| 546 |
irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_LEVEL_LOW); |
| 547 |
irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_LEVEL_LOW); |
| 548 |
irq_set_irq_type(AU1550_GPIO201_205_INT, IRQ_TYPE_LEVEL_HIGH); |
| 549 |
|
| 550 |
/* enable both PCMCIA card irqs in the shared line */ |
| 551 |
alchemy_gpio2_enable_int(201); /* socket 0 card irq */ |
| 552 |
alchemy_gpio2_enable_int(202); /* socket 1 card irq */ |
| 553 |
|
| 554 |
/* Pb1550, like all others, also has statuschange irqs; however they're |
| 555 |
* wired up on one of the Au1550's shared GPIO201_205 line, which also |
| 556 |
* services the PCMCIA card interrupts. So we ignore statuschange and |
| 557 |
* use the GPIO201_205 exclusively for card interrupts, since a) pcmcia |
| 558 |
* drivers are used to shared irqs and b) statuschange isn't really use- |
| 559 |
* ful anyway. |
| 560 |
*/ |
| 561 |
db1x_register_pcmcia_socket( |
| 562 |
AU1000_PCMCIA_ATTR_PHYS_ADDR, |
| 563 |
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1, |
| 564 |
AU1000_PCMCIA_MEM_PHYS_ADDR, |
| 565 |
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1, |
| 566 |
AU1000_PCMCIA_IO_PHYS_ADDR, |
| 567 |
AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1, |
| 568 |
AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0); |
| 569 |
|
| 570 |
db1x_register_pcmcia_socket( |
| 571 |
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000, |
| 572 |
AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1, |
| 573 |
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000, |
| 574 |
AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1, |
| 575 |
AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000, |
| 576 |
AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1, |
| 577 |
AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1); |
| 578 |
|
| 579 |
pb1550_nand_setup(); |
| 580 |
} |
| 581 |
|
| 582 |
int __init db1550_dev_setup(void) |
| 583 |
{ |
| 584 |
int swapped, id; |
| 585 |
struct clk *c; |
| 586 |
|
| 587 |
id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550); |
| 588 |
|
| 589 |
i2c_register_board_info(0, db1550_i2c_devs, |
| 590 |
ARRAY_SIZE(db1550_i2c_devs)); |
| 591 |
spi_register_board_info(db1550_spi_devs, |
| 592 |
ARRAY_SIZE(db1550_spi_devs)); |
| 593 |
|
| 594 |
c = clk_get(NULL, "psc0_intclk"); |
| 595 |
if (!IS_ERR(c)) { |
| 596 |
clk_set_rate(c, 50000000); |
| 597 |
clk_prepare_enable(c); |
| 598 |
clk_put(c); |
| 599 |
} |
| 600 |
c = clk_get(NULL, "psc2_intclk"); |
| 601 |
if (!IS_ERR(c)) { |
| 602 |
clk_set_rate(c, db1550_spi_platdata.mainclk_hz); |
| 603 |
clk_prepare_enable(c); |
| 604 |
clk_put(c); |
| 605 |
} |
| 606 |
|
| 607 |
/* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */ |
| 608 |
__raw_writel(PSC_SEL_CLK_SERCLK, |
| 609 |
(void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET); |
| 610 |
wmb(); |
| 611 |
__raw_writel(PSC_SEL_CLK_SERCLK, |
| 612 |
(void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET); |
| 613 |
wmb(); |
| 614 |
/* SPI/I2C use internally supplied 50MHz source */ |
| 615 |
__raw_writel(PSC_SEL_CLK_INTCLK, |
| 616 |
(void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET); |
| 617 |
wmb(); |
| 618 |
__raw_writel(PSC_SEL_CLK_INTCLK, |
| 619 |
(void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET); |
| 620 |
wmb(); |
| 621 |
|
| 622 |
id ? pb1550_devices() : db1550_devices(); |
| 623 |
|
| 624 |
swapped = bcsr_read(BCSR_STATUS) & |
| 625 |
(id ? BCSR_STATUS_PB1550_SWAPBOOT : BCSR_STATUS_DB1000_SWAPBOOT); |
| 626 |
db1x_register_norflash(128 << 20, 4, swapped); |
| 627 |
|
| 628 |
return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs)); |
| 629 |
} |