| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* MTX-1 platform devices registration (Au1500) |
| 4 |
* |
| 5 |
* Copyright (C) 2007-2009, Florian Fainelli <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
#include <linux/init.h> |
| 9 |
#include <linux/interrupt.h> |
| 10 |
#include <linux/kernel.h> |
| 11 |
#include <linux/platform_device.h> |
| 12 |
#include <linux/gpio/machine.h> |
| 13 |
#include <linux/gpio/property.h> |
| 14 |
#include <linux/input.h> |
| 15 |
#include <linux/mtd/partitions.h> |
| 16 |
#include <linux/mtd/physmap.h> |
| 17 |
#include <mtd/mtd-abi.h> |
| 18 |
#include <asm/bootinfo.h> |
| 19 |
#include <asm/reboot.h> |
| 20 |
#include <asm/setup.h> |
| 21 |
#include <asm/mach-au1x00/au1000.h> |
| 22 |
#include <asm/mach-au1x00/gpio-au1000.h> |
| 23 |
#include <asm/mach-au1x00/au1xxx_eth.h> |
| 24 |
#include <prom.h> |
| 25 |
|
| 26 |
const char *get_system_type(void) |
| 27 |
{ |
| 28 |
return "MTX-1"; |
| 29 |
} |
| 30 |
|
| 31 |
void prom_putchar(char c) |
| 32 |
{ |
| 33 |
alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c); |
| 34 |
} |
| 35 |
|
| 36 |
static void mtx1_reset(char *c) |
| 37 |
{ |
| 38 |
/* Jump to the reset vector */ |
| 39 |
__asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000)); |
| 40 |
} |
| 41 |
|
| 42 |
static void mtx1_power_off(void) |
| 43 |
{ |
| 44 |
while (1) |
| 45 |
asm volatile ( |
| 46 |
" .set mips32 \n" |
| 47 |
" wait \n" |
| 48 |
" .set mips0 \n"); |
| 49 |
} |
| 50 |
|
| 51 |
void __init board_setup(void) |
| 52 |
{ |
| 53 |
#if IS_ENABLED(CONFIG_USB_OHCI_HCD) |
| 54 |
/* Enable USB power switch */ |
| 55 |
alchemy_gpio_direction_output(204, 0); |
| 56 |
#endif /* IS_ENABLED(CONFIG_USB_OHCI_HCD) */ |
| 57 |
|
| 58 |
/* Initialize sys_pinfunc */ |
| 59 |
alchemy_wrsys(SYS_PF_NI2, AU1000_SYS_PINFUNC); |
| 60 |
|
| 61 |
/* Initialize GPIO */ |
| 62 |
alchemy_wrsys(~0, AU1000_SYS_TRIOUTCLR); |
| 63 |
alchemy_gpio_direction_output(0, 0); /* Disable M66EN (PCI 66MHz) */ |
| 64 |
alchemy_gpio_direction_output(3, 1); /* Disable PCI CLKRUN# */ |
| 65 |
alchemy_gpio_direction_output(1, 1); /* Enable EXT_IO3 */ |
| 66 |
alchemy_gpio_direction_output(5, 0); /* Disable eth PHY TX_ER */ |
| 67 |
|
| 68 |
/* Enable LED and set it to green */ |
| 69 |
alchemy_gpio_direction_output(211, 1); /* green on */ |
| 70 |
alchemy_gpio_direction_output(212, 0); /* red off */ |
| 71 |
|
| 72 |
pm_power_off = mtx1_power_off; |
| 73 |
_machine_halt = mtx1_power_off; |
| 74 |
_machine_restart = mtx1_reset; |
| 75 |
|
| 76 |
printk(KERN_INFO "4G Systems MTX-1 Board\n"); |
| 77 |
} |
| 78 |
|
| 79 |
/******************************************************************************/ |
| 80 |
|
| 81 |
static const struct software_node mtx1_gpiochip_node = { |
| 82 |
.name = "alchemy-gpio2", |
| 83 |
}; |
| 84 |
|
| 85 |
static const struct software_node mtx1_gpio_keys_node = { |
| 86 |
.name = "mtx1-gpio-keys", |
| 87 |
}; |
| 88 |
|
| 89 |
static const struct property_entry mtx1_button_props[] = { |
| 90 |
PROPERTY_ENTRY_U32("linux,code", BTN_0), |
| 91 |
PROPERTY_ENTRY_GPIO("gpios", &mtx1_gpiochip_node, 7, GPIO_ACTIVE_HIGH), |
| 92 |
PROPERTY_ENTRY_STRING("label", "System button"), |
| 93 |
{ } |
| 94 |
}; |
| 95 |
|
| 96 |
static const struct software_node mtx1_button_node = { |
| 97 |
.parent = &mtx1_gpio_keys_node, |
| 98 |
.properties = mtx1_button_props, |
| 99 |
}; |
| 100 |
|
| 101 |
static const struct software_node *mtx1_gpio_keys_swnodes[] __initconst = { |
| 102 |
&mtx1_gpio_keys_node, |
| 103 |
&mtx1_button_node, |
| 104 |
NULL |
| 105 |
}; |
| 106 |
|
| 107 |
static void __init mtx1_keys_init(void) |
| 108 |
{ |
| 109 |
struct platform_device_info keys_info = { |
| 110 |
.name = "gpio-keys", |
| 111 |
.id = PLATFORM_DEVID_NONE, |
| 112 |
}; |
| 113 |
struct platform_device *pd; |
| 114 |
int err; |
| 115 |
|
| 116 |
err = software_node_register_node_group(mtx1_gpio_keys_swnodes); |
| 117 |
if (err) { |
| 118 |
pr_err("failed to register gpio-keys software nodes: %d\n", err); |
| 119 |
return; |
| 120 |
} |
| 121 |
|
| 122 |
keys_info.fwnode = software_node_fwnode(&mtx1_gpio_keys_node); |
| 123 |
|
| 124 |
pd = platform_device_register_full(&keys_info); |
| 125 |
err = PTR_ERR_OR_ZERO(pd); |
| 126 |
if (err) |
| 127 |
pr_err("failed to create gpio-keys device: %d\n", err); |
| 128 |
} |
| 129 |
|
| 130 |
/* Global number 215 is offset 15 on Alchemy GPIO 2 */ |
| 131 |
static const struct property_entry mtx1_wdt_props[] = { |
| 132 |
PROPERTY_ENTRY_GPIO("gpios", &mtx1_gpiochip_node, 15, GPIO_ACTIVE_HIGH), |
| 133 |
{ } |
| 134 |
}; |
| 135 |
|
| 136 |
static struct platform_device_info mtx1_wdt_info __initconst = { |
| 137 |
.name = "mtx1-wdt", |
| 138 |
.id = 0, |
| 139 |
.properties = mtx1_wdt_props, |
| 140 |
}; |
| 141 |
|
| 142 |
static void __init mtx1_wdt_init(void) |
| 143 |
{ |
| 144 |
struct platform_device *pd; |
| 145 |
int err; |
| 146 |
|
| 147 |
pd = platform_device_register_full(&mtx1_wdt_info); |
| 148 |
err = PTR_ERR_OR_ZERO(pd); |
| 149 |
if (err) |
| 150 |
pr_err("failed to create gpio-keys device: %d\n", err); |
| 151 |
} |
| 152 |
|
| 153 |
static const struct software_node mtx1_gpio_leds_node = { |
| 154 |
.name = "mtx1-leds", |
| 155 |
}; |
| 156 |
|
| 157 |
static const struct property_entry mtx1_green_led_props[] = { |
| 158 |
PROPERTY_ENTRY_GPIO("gpios", &mtx1_gpiochip_node, 11, GPIO_ACTIVE_HIGH), |
| 159 |
{ } |
| 160 |
}; |
| 161 |
|
| 162 |
static const struct software_node mtx1_green_led_node = { |
| 163 |
.name = "mtx1:green", |
| 164 |
.parent = &mtx1_gpio_leds_node, |
| 165 |
.properties = mtx1_green_led_props, |
| 166 |
}; |
| 167 |
|
| 168 |
static const struct property_entry mtx1_red_led_props[] = { |
| 169 |
PROPERTY_ENTRY_GPIO("gpios", &mtx1_gpiochip_node, 12, GPIO_ACTIVE_HIGH), |
| 170 |
{ } |
| 171 |
}; |
| 172 |
|
| 173 |
static const struct software_node mtx1_red_led_node = { |
| 174 |
.name = "mtx1:red", |
| 175 |
.parent = &mtx1_gpio_leds_node, |
| 176 |
.properties = mtx1_red_led_props, |
| 177 |
}; |
| 178 |
|
| 179 |
static const struct software_node *mtx1_gpio_leds_swnodes[] = { |
| 180 |
&mtx1_gpio_leds_node, |
| 181 |
&mtx1_green_led_node, |
| 182 |
&mtx1_red_led_node, |
| 183 |
NULL |
| 184 |
}; |
| 185 |
|
| 186 |
static void __init mtx1_leds_init(void) |
| 187 |
{ |
| 188 |
struct platform_device_info led_info = { |
| 189 |
.name = "leds-gpio", |
| 190 |
.id = PLATFORM_DEVID_NONE, |
| 191 |
}; |
| 192 |
struct platform_device *led_dev; |
| 193 |
int err; |
| 194 |
|
| 195 |
err = software_node_register_node_group(mtx1_gpio_leds_swnodes); |
| 196 |
if (err) { |
| 197 |
pr_err("failed to register LED software nodes: %d\n", err); |
| 198 |
return; |
| 199 |
} |
| 200 |
|
| 201 |
led_info.fwnode = software_node_fwnode(&mtx1_gpio_leds_node); |
| 202 |
|
| 203 |
led_dev = platform_device_register_full(&led_info); |
| 204 |
err = PTR_ERR_OR_ZERO(led_dev); |
| 205 |
if (err) |
| 206 |
pr_err("failed to create LED device: %d\n", err); |
| 207 |
} |
| 208 |
|
| 209 |
static struct mtd_partition mtx1_mtd_partitions[] = { |
| 210 |
{ |
| 211 |
.name = "filesystem", |
| 212 |
.size = 0x01C00000, |
| 213 |
.offset = 0, |
| 214 |
}, |
| 215 |
{ |
| 216 |
.name = "yamon", |
| 217 |
.size = 0x00100000, |
| 218 |
.offset = MTDPART_OFS_APPEND, |
| 219 |
.mask_flags = MTD_WRITEABLE, |
| 220 |
}, |
| 221 |
{ |
| 222 |
.name = "kernel", |
| 223 |
.size = 0x002c0000, |
| 224 |
.offset = MTDPART_OFS_APPEND, |
| 225 |
}, |
| 226 |
{ |
| 227 |
.name = "yamon env", |
| 228 |
.size = 0x00040000, |
| 229 |
.offset = MTDPART_OFS_APPEND, |
| 230 |
}, |
| 231 |
}; |
| 232 |
|
| 233 |
static struct physmap_flash_data mtx1_flash_data = { |
| 234 |
.width = 4, |
| 235 |
.nr_parts = 4, |
| 236 |
.parts = mtx1_mtd_partitions, |
| 237 |
}; |
| 238 |
|
| 239 |
static struct resource mtx1_mtd_resource = { |
| 240 |
.start = 0x1e000000, |
| 241 |
.end = 0x1fffffff, |
| 242 |
.flags = IORESOURCE_MEM, |
| 243 |
}; |
| 244 |
|
| 245 |
static struct platform_device mtx1_mtd = { |
| 246 |
.name = "physmap-flash", |
| 247 |
.dev = { |
| 248 |
.platform_data = &mtx1_flash_data, |
| 249 |
}, |
| 250 |
.num_resources = 1, |
| 251 |
.resource = &mtx1_mtd_resource, |
| 252 |
}; |
| 253 |
|
| 254 |
static struct resource alchemy_pci_host_res[] = { |
| 255 |
[0] = { |
| 256 |
.start = AU1500_PCI_PHYS_ADDR, |
| 257 |
.end = AU1500_PCI_PHYS_ADDR + 0xfff, |
| 258 |
.flags = IORESOURCE_MEM, |
| 259 |
}, |
| 260 |
}; |
| 261 |
|
| 262 |
static int mtx1_pci_idsel(unsigned int devsel, int assert) |
| 263 |
{ |
| 264 |
/* This function is only necessary to support a proprietary Cardbus |
| 265 |
* adapter on the mtx-1 "singleboard" variant. It triggers a custom |
| 266 |
* logic chip connected to EXT_IO3 (GPIO1) to suppress IDSEL signals. |
| 267 |
*/ |
| 268 |
udelay(1); |
| 269 |
|
| 270 |
if (assert && devsel != 0) |
| 271 |
/* Suppress signal to Cardbus */ |
| 272 |
alchemy_gpio_set_value(1, 0); /* set EXT_IO3 OFF */ |
| 273 |
else |
| 274 |
alchemy_gpio_set_value(1, 1); /* set EXT_IO3 ON */ |
| 275 |
|
| 276 |
udelay(1); |
| 277 |
return 1; |
| 278 |
} |
| 279 |
|
| 280 |
static const char mtx1_irqtab[][5] = { |
| 281 |
[0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */ |
| 282 |
[1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */ |
| 283 |
[2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */ |
| 284 |
[3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */ |
| 285 |
[4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */ |
| 286 |
[5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */ |
| 287 |
[6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */ |
| 288 |
[7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */ |
| 289 |
}; |
| 290 |
|
| 291 |
static int mtx1_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin) |
| 292 |
{ |
| 293 |
return mtx1_irqtab[slot][pin]; |
| 294 |
} |
| 295 |
|
| 296 |
static struct alchemy_pci_platdata mtx1_pci_pd = { |
| 297 |
.board_map_irq = mtx1_map_pci_irq, |
| 298 |
.board_pci_idsel = mtx1_pci_idsel, |
| 299 |
.pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H | |
| 300 |
PCI_CONFIG_CH | |
| 301 |
#if defined(__MIPSEB__) |
| 302 |
PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM, |
| 303 |
#else |
| 304 |
0, |
| 305 |
#endif |
| 306 |
}; |
| 307 |
|
| 308 |
static struct platform_device mtx1_pci_host = { |
| 309 |
.dev.platform_data = &mtx1_pci_pd, |
| 310 |
.name = "alchemy-pci", |
| 311 |
.id = 0, |
| 312 |
.num_resources = ARRAY_SIZE(alchemy_pci_host_res), |
| 313 |
.resource = alchemy_pci_host_res, |
| 314 |
}; |
| 315 |
|
| 316 |
static struct platform_device *mtx1_devs[] __initdata = { |
| 317 |
&mtx1_pci_host, |
| 318 |
&mtx1_mtd, |
| 319 |
}; |
| 320 |
|
| 321 |
static struct au1000_eth_platform_data mtx1_au1000_eth0_pdata = { |
| 322 |
.phy_search_highest_addr = 1, |
| 323 |
.phy1_search_mac0 = 1, |
| 324 |
}; |
| 325 |
|
| 326 |
static int __init mtx1_register_devices(void) |
| 327 |
{ |
| 328 |
int rc; |
| 329 |
|
| 330 |
irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_HIGH); |
| 331 |
irq_set_irq_type(AU1500_GPIO201_INT, IRQ_TYPE_LEVEL_LOW); |
| 332 |
irq_set_irq_type(AU1500_GPIO202_INT, IRQ_TYPE_LEVEL_LOW); |
| 333 |
irq_set_irq_type(AU1500_GPIO203_INT, IRQ_TYPE_LEVEL_LOW); |
| 334 |
irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW); |
| 335 |
|
| 336 |
au1xxx_override_eth_cfg(0, &mtx1_au1000_eth0_pdata); |
| 337 |
|
| 338 |
rc = software_node_register(&mtx1_gpiochip_node); |
| 339 |
if (rc) |
| 340 |
return rc; |
| 341 |
|
| 342 |
rc = platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs)); |
| 343 |
if (rc) |
| 344 |
return rc; |
| 345 |
|
| 346 |
mtx1_leds_init(); |
| 347 |
mtx1_wdt_init(); |
| 348 |
mtx1_keys_init(); |
| 349 |
|
| 350 |
return 0; |
| 351 |
} |
| 352 |
arch_initcall(mtx1_register_devices); |