| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Copyright (C) 2008-2009 Manuel Lauss <[email protected]> |
| 4 |
* |
| 5 |
* Previous incarnations were: |
| 6 |
* Copyright (C) 2001, 2006, 2008 MontaVista Software, <[email protected]> |
| 7 |
* Copied and modified Carsten Langgaard's time.c |
| 8 |
* |
| 9 |
* Carsten Langgaard, [email protected] |
| 10 |
* Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved. |
| 11 |
* |
| 12 |
* ######################################################################## |
| 13 |
* |
| 14 |
* ######################################################################## |
| 15 |
* |
| 16 |
* Clocksource/event using the 32.768kHz-clocked Counter1 ('RTC' in the |
| 17 |
* databooks). Firmware/Board init code must enable the counters in the |
| 18 |
* counter control register, otherwise the CP0 counter clocksource/event |
| 19 |
* will be installed instead (and use of 'wait' instruction is prohibited). |
| 20 |
*/ |
| 21 |
|
| 22 |
#include <linux/clockchips.h> |
| 23 |
#include <linux/clocksource.h> |
| 24 |
#include <linux/interrupt.h> |
| 25 |
#include <linux/spinlock.h> |
| 26 |
|
| 27 |
#include <asm/idle.h> |
| 28 |
#include <asm/processor.h> |
| 29 |
#include <asm/time.h> |
| 30 |
#include <asm/mach-au1x00/au1000.h> |
| 31 |
|
| 32 |
/* 32kHz clock enabled and detected */ |
| 33 |
#define CNTR_OK (SYS_CNTRL_E0 | SYS_CNTRL_32S) |
| 34 |
|
| 35 |
static u64 au1x_counter1_read(struct clocksource *cs) |
| 36 |
{ |
| 37 |
return alchemy_rdsys(AU1000_SYS_RTCREAD); |
| 38 |
} |
| 39 |
|
| 40 |
static struct clocksource au1x_counter1_clocksource = { |
| 41 |
.name = "alchemy-counter1", |
| 42 |
.read = au1x_counter1_read, |
| 43 |
.mask = CLOCKSOURCE_MASK(32), |
| 44 |
.flags = CLOCK_SOURCE_IS_CONTINUOUS, |
| 45 |
.rating = 1500, |
| 46 |
}; |
| 47 |
|
| 48 |
static int au1x_rtcmatch2_set_next_event(unsigned long delta, |
| 49 |
struct clock_event_device *cd) |
| 50 |
{ |
| 51 |
delta += alchemy_rdsys(AU1000_SYS_RTCREAD); |
| 52 |
/* wait for register access */ |
| 53 |
while (alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_M21) |
| 54 |
; |
| 55 |
alchemy_wrsys(delta, AU1000_SYS_RTCMATCH2); |
| 56 |
|
| 57 |
return 0; |
| 58 |
} |
| 59 |
|
| 60 |
static irqreturn_t au1x_rtcmatch2_irq(int irq, void *dev_id) |
| 61 |
{ |
| 62 |
struct clock_event_device *cd = dev_id; |
| 63 |
cd->event_handler(cd); |
| 64 |
return IRQ_HANDLED; |
| 65 |
} |
| 66 |
|
| 67 |
static struct clock_event_device au1x_rtcmatch2_clockdev = { |
| 68 |
.name = "rtcmatch2", |
| 69 |
.features = CLOCK_EVT_FEAT_ONESHOT, |
| 70 |
.rating = 1500, |
| 71 |
.set_next_event = au1x_rtcmatch2_set_next_event, |
| 72 |
.cpumask = cpu_possible_mask, |
| 73 |
}; |
| 74 |
|
| 75 |
static int __init alchemy_time_init(unsigned int m2int) |
| 76 |
{ |
| 77 |
struct clock_event_device *cd = &au1x_rtcmatch2_clockdev; |
| 78 |
unsigned long t; |
| 79 |
|
| 80 |
au1x_rtcmatch2_clockdev.irq = m2int; |
| 81 |
|
| 82 |
/* Check if firmware (YAMON, ...) has enabled 32kHz and clock |
| 83 |
* has been detected. If so install the rtcmatch2 clocksource, |
| 84 |
* otherwise don't bother. Note that both bits being set is by |
| 85 |
* no means a definite guarantee that the counters actually work |
| 86 |
* (the 32S bit seems to be stuck set to 1 once a single clock- |
| 87 |
* edge is detected, hence the timeouts). |
| 88 |
*/ |
| 89 |
if (CNTR_OK != (alchemy_rdsys(AU1000_SYS_CNTRCTRL) & CNTR_OK)) |
| 90 |
goto cntr_err; |
| 91 |
|
| 92 |
/* |
| 93 |
* setup counter 1 (RTC) to tick at full speed |
| 94 |
*/ |
| 95 |
t = 0xffffff; |
| 96 |
while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_T1S) && --t) |
| 97 |
asm volatile ("nop"); |
| 98 |
if (!t) |
| 99 |
goto cntr_err; |
| 100 |
|
| 101 |
alchemy_wrsys(0, AU1000_SYS_RTCTRIM); /* 32.768 kHz */ |
| 102 |
|
| 103 |
t = 0xffffff; |
| 104 |
while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_C1S) && --t) |
| 105 |
asm volatile ("nop"); |
| 106 |
if (!t) |
| 107 |
goto cntr_err; |
| 108 |
alchemy_wrsys(0, AU1000_SYS_RTCWRITE); |
| 109 |
|
| 110 |
t = 0xffffff; |
| 111 |
while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_C1S) && --t) |
| 112 |
asm volatile ("nop"); |
| 113 |
if (!t) |
| 114 |
goto cntr_err; |
| 115 |
|
| 116 |
/* register counter1 clocksource and event device */ |
| 117 |
clocksource_register_hz(&au1x_counter1_clocksource, 32768); |
| 118 |
|
| 119 |
cd->shift = 32; |
| 120 |
cd->mult = div_sc(32768, NSEC_PER_SEC, cd->shift); |
| 121 |
cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd); |
| 122 |
cd->max_delta_ticks = 0xffffffff; |
| 123 |
cd->min_delta_ns = clockevent_delta2ns(9, cd); |
| 124 |
cd->min_delta_ticks = 9; /* ~0.28ms */ |
| 125 |
clockevents_register_device(cd); |
| 126 |
if (request_irq(m2int, au1x_rtcmatch2_irq, IRQF_TIMER, "timer", |
| 127 |
&au1x_rtcmatch2_clockdev)) |
| 128 |
pr_err("Failed to register timer interrupt\n"); |
| 129 |
|
| 130 |
printk(KERN_INFO "Alchemy clocksource installed\n"); |
| 131 |
|
| 132 |
return 0; |
| 133 |
|
| 134 |
cntr_err: |
| 135 |
return -1; |
| 136 |
} |
| 137 |
|
| 138 |
static int alchemy_m2inttab[] __initdata = { |
| 139 |
AU1000_RTC_MATCH2_INT, |
| 140 |
AU1500_RTC_MATCH2_INT, |
| 141 |
AU1100_RTC_MATCH2_INT, |
| 142 |
AU1550_RTC_MATCH2_INT, |
| 143 |
AU1200_RTC_MATCH2_INT, |
| 144 |
AU1300_RTC_MATCH2_INT, |
| 145 |
}; |
| 146 |
|
| 147 |
void __init plat_time_init(void) |
| 148 |
{ |
| 149 |
int t; |
| 150 |
|
| 151 |
t = alchemy_get_cputype(); |
| 152 |
if (t == ALCHEMY_CPU_UNKNOWN || |
| 153 |
alchemy_time_init(alchemy_m2inttab[t])) |
| 154 |
cpu_wait = NULL; /* wait doesn't work with r4k timer */ |
| 155 |
} |