| 1 |
.. SPDX-License-Identifier: GPL-2.0 |
| 2 |
|
| 3 |
The cafe_ccic driver |
| 4 |
==================== |
| 5 |
|
| 6 |
Author: Jonathan Corbet <[email protected]> |
| 7 |
|
| 8 |
Introduction |
| 9 |
------------ |
| 10 |
|
| 11 |
"cafe_ccic" is a driver for the Marvell 88ALP01 "cafe" CMOS camera |
| 12 |
controller. This is the controller found in first-generation OLPC systems, |
| 13 |
and this driver was written with support from the OLPC project. |
| 14 |
|
| 15 |
Current status: the core driver works. It can generate data in YUV422, |
| 16 |
RGB565, and RGB444 formats. (Anybody looking at the code will see RGB32 as |
| 17 |
well, but that is a debugging aid which will be removed shortly). VGA and |
| 18 |
QVGA modes work; CIF is there but the colors remain funky. Only the OV7670 |
| 19 |
sensor is known to work with this controller at this time. |
| 20 |
|
| 21 |
To try it out: either of these commands will work: |
| 22 |
|
| 23 |
.. code-block:: none |
| 24 |
|
| 25 |
$ mplayer tv:// -tv driver=v4l2:width=640:height=480 -nosound |
| 26 |
$ mplayer tv:// -tv driver=v4l2:width=640:height=480:outfmt=bgr16 -nosound |
| 27 |
|
| 28 |
The "xawtv" utility also works; gqcam does not, for unknown reasons. |
| 29 |
|
| 30 |
Load time options |
| 31 |
----------------- |
| 32 |
|
| 33 |
There are a few load-time options, most of which can be changed after |
| 34 |
loading via sysfs as well: |
| 35 |
|
| 36 |
- alloc_bufs_at_load: Normally, the driver will not allocate any DMA |
| 37 |
buffers until the time comes to transfer data. If this option is set, |
| 38 |
then worst-case-sized buffers will be allocated at module load time. |
| 39 |
This option nails down the memory for the life of the module, but |
| 40 |
perhaps decreases the chances of an allocation failure later on. |
| 41 |
|
| 42 |
- dma_buf_size: The size of DMA buffers to allocate. Note that this |
| 43 |
option is only consulted for load-time allocation; when buffers are |
| 44 |
allocated at run time, they will be sized appropriately for the current |
| 45 |
camera settings. |
| 46 |
|
| 47 |
- n_dma_bufs: The controller can cycle through either two or three DMA |
| 48 |
buffers. Normally, the driver tries to use three buffers; on faster |
| 49 |
systems, however, it will work well with only two. |
| 50 |
|
| 51 |
- min_buffers: The minimum number of streaming I/O buffers that the driver |
| 52 |
will consent to work with. Default is one, but, on slower systems, |
| 53 |
better behavior with mplayer can be achieved by setting to a higher |
| 54 |
value (like six). |
| 55 |
|
| 56 |
- max_buffers: The maximum number of streaming I/O buffers; default is |
| 57 |
ten. That number was carefully picked out of a hat and should not be |
| 58 |
assumed to actually mean much of anything. |
| 59 |
|
| 60 |
- flip: If this boolean parameter is set, the sensor will be instructed to |
| 61 |
invert the video image. Whether it makes sense is determined by how |
| 62 |
your particular camera is mounted. |