| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Low-Level PCI Support for the SH7751 |
| 4 |
* |
| 5 |
* Copyright (C) 2003 - 2009 Paul Mundt |
| 6 |
* Copyright (C) 2001 Dustin McIntire |
| 7 |
* |
| 8 |
* With cleanup by Paul van Gool <[email protected]>, 2003. |
| 9 |
*/ |
| 10 |
#include <linux/init.h> |
| 11 |
#include <linux/pci.h> |
| 12 |
#include <linux/types.h> |
| 13 |
#include <linux/errno.h> |
| 14 |
#include <linux/io.h> |
| 15 |
#include "pci-sh4.h" |
| 16 |
#include <asm/addrspace.h> |
| 17 |
#include <linux/sizes.h> |
| 18 |
|
| 19 |
static int __init __area_sdram_check(struct pci_channel *chan, |
| 20 |
unsigned int area) |
| 21 |
{ |
| 22 |
unsigned long word; |
| 23 |
|
| 24 |
word = __raw_readl(SH7751_BCR1); |
| 25 |
/* check BCR for SDRAM in area */ |
| 26 |
if (((word >> area) & 1) == 0) { |
| 27 |
printk("PCI: Area %d is not configured for SDRAM. BCR1=0x%lx\n", |
| 28 |
area, word); |
| 29 |
return 0; |
| 30 |
} |
| 31 |
pci_write_reg(chan, word, SH4_PCIBCR1); |
| 32 |
|
| 33 |
word = __raw_readw(SH7751_BCR2); |
| 34 |
/* check BCR2 for 32bit SDRAM interface*/ |
| 35 |
if (((word >> (area << 1)) & 0x3) != 0x3) { |
| 36 |
printk("PCI: Area %d is not 32 bit SDRAM. BCR2=0x%lx\n", |
| 37 |
area, word); |
| 38 |
return 0; |
| 39 |
} |
| 40 |
pci_write_reg(chan, word, SH4_PCIBCR2); |
| 41 |
|
| 42 |
return 1; |
| 43 |
} |
| 44 |
|
| 45 |
static struct resource sh7751_pci_resources[] = { |
| 46 |
{ |
| 47 |
.name = "SH7751_IO", |
| 48 |
.start = 0x1000, |
| 49 |
.end = SZ_4M - 1, |
| 50 |
.flags = IORESOURCE_IO |
| 51 |
}, { |
| 52 |
.name = "SH7751_mem", |
| 53 |
.start = SH7751_PCI_MEMORY_BASE, |
| 54 |
.end = SH7751_PCI_MEMORY_BASE + SH7751_PCI_MEM_SIZE - 1, |
| 55 |
.flags = IORESOURCE_MEM |
| 56 |
}, |
| 57 |
}; |
| 58 |
|
| 59 |
static struct pci_channel sh7751_pci_controller = { |
| 60 |
.pci_ops = &sh4_pci_ops, |
| 61 |
.resources = sh7751_pci_resources, |
| 62 |
.nr_resources = ARRAY_SIZE(sh7751_pci_resources), |
| 63 |
.mem_offset = 0x00000000, |
| 64 |
.io_offset = 0x00000000, |
| 65 |
.io_map_base = SH7751_PCI_IO_BASE, |
| 66 |
}; |
| 67 |
|
| 68 |
static struct sh4_pci_address_map sh7751_pci_map = { |
| 69 |
.window0 = { |
| 70 |
.base = SH7751_CS3_BASE_ADDR, |
| 71 |
.size = 0x04000000, |
| 72 |
}, |
| 73 |
}; |
| 74 |
|
| 75 |
static int __init sh7751_pci_init(void) |
| 76 |
{ |
| 77 |
struct pci_channel *chan = &sh7751_pci_controller; |
| 78 |
unsigned int id; |
| 79 |
u32 word, reg; |
| 80 |
|
| 81 |
printk(KERN_NOTICE "PCI: Starting initialization.\n"); |
| 82 |
|
| 83 |
chan->reg_base = 0xfe200000; |
| 84 |
|
| 85 |
/* check for SH7751/SH7751R hardware */ |
| 86 |
id = pci_read_reg(chan, SH7751_PCICONF0); |
| 87 |
if (id != ((SH7751_DEVICE_ID << 16) | SH7751_VENDOR_ID) && |
| 88 |
id != ((SH7751R_DEVICE_ID << 16) | SH7751_VENDOR_ID)) { |
| 89 |
pr_debug("PCI: This is not an SH7751(R) (%x)\n", id); |
| 90 |
return -ENODEV; |
| 91 |
} |
| 92 |
|
| 93 |
/* Set the BCR's to enable PCI access */ |
| 94 |
reg = __raw_readl(SH7751_BCR1); |
| 95 |
reg |= 0x80000; |
| 96 |
__raw_writel(reg, SH7751_BCR1); |
| 97 |
|
| 98 |
/* Turn the clocks back on (not done in reset)*/ |
| 99 |
pci_write_reg(chan, 0, SH4_PCICLKR); |
| 100 |
/* Clear Powerdown IRQ's (not done in reset) */ |
| 101 |
word = SH4_PCIPINT_D3 | SH4_PCIPINT_D0; |
| 102 |
pci_write_reg(chan, word, SH4_PCIPINT); |
| 103 |
|
| 104 |
/* set the command/status bits to: |
| 105 |
* Wait Cycle Control + Parity Enable + Bus Master + |
| 106 |
* Mem space enable |
| 107 |
*/ |
| 108 |
word = SH7751_PCICONF1_WCC | SH7751_PCICONF1_PER | |
| 109 |
SH7751_PCICONF1_BUM | SH7751_PCICONF1_MES; |
| 110 |
pci_write_reg(chan, word, SH7751_PCICONF1); |
| 111 |
|
| 112 |
/* define this host as the host bridge */ |
| 113 |
word = PCI_BASE_CLASS_BRIDGE << 24; |
| 114 |
pci_write_reg(chan, word, SH7751_PCICONF2); |
| 115 |
|
| 116 |
/* Set IO and Mem windows to local address |
| 117 |
* Make PCI and local address the same for easy 1 to 1 mapping |
| 118 |
*/ |
| 119 |
word = sh7751_pci_map.window0.size - 1; |
| 120 |
pci_write_reg(chan, word, SH4_PCILSR0); |
| 121 |
/* Set the values on window 0 PCI config registers */ |
| 122 |
word = P2SEGADDR(sh7751_pci_map.window0.base); |
| 123 |
pci_write_reg(chan, word, SH4_PCILAR0); |
| 124 |
pci_write_reg(chan, word, SH7751_PCICONF5); |
| 125 |
|
| 126 |
/* Set the local 16MB PCI memory space window to |
| 127 |
* the lowest PCI mapped address |
| 128 |
*/ |
| 129 |
word = chan->resources[1].start & SH4_PCIMBR_MASK; |
| 130 |
pr_debug("PCI: Setting upper bits of Memory window to 0x%x\n", word); |
| 131 |
pci_write_reg(chan, word , SH4_PCIMBR); |
| 132 |
|
| 133 |
/* Make sure the MSB's of IO window are set to access PCI space |
| 134 |
* correctly */ |
| 135 |
word = chan->resources[0].start & SH4_PCIIOBR_MASK; |
| 136 |
pr_debug("PCI: Setting upper bits of IO window to 0x%x\n", word); |
| 137 |
pci_write_reg(chan, word, SH4_PCIIOBR); |
| 138 |
|
| 139 |
/* Set PCI WCRx, BCRx's, copy from BSC locations */ |
| 140 |
|
| 141 |
/* check BCR for SDRAM in specified area */ |
| 142 |
switch (sh7751_pci_map.window0.base) { |
| 143 |
case SH7751_CS0_BASE_ADDR: word = __area_sdram_check(chan, 0); break; |
| 144 |
case SH7751_CS1_BASE_ADDR: word = __area_sdram_check(chan, 1); break; |
| 145 |
case SH7751_CS2_BASE_ADDR: word = __area_sdram_check(chan, 2); break; |
| 146 |
case SH7751_CS3_BASE_ADDR: word = __area_sdram_check(chan, 3); break; |
| 147 |
case SH7751_CS4_BASE_ADDR: word = __area_sdram_check(chan, 4); break; |
| 148 |
case SH7751_CS5_BASE_ADDR: word = __area_sdram_check(chan, 5); break; |
| 149 |
case SH7751_CS6_BASE_ADDR: word = __area_sdram_check(chan, 6); break; |
| 150 |
} |
| 151 |
|
| 152 |
if (!word) |
| 153 |
return -1; |
| 154 |
|
| 155 |
/* configure the wait control registers */ |
| 156 |
word = __raw_readl(SH7751_WCR1); |
| 157 |
pci_write_reg(chan, word, SH4_PCIWCR1); |
| 158 |
word = __raw_readl(SH7751_WCR2); |
| 159 |
pci_write_reg(chan, word, SH4_PCIWCR2); |
| 160 |
word = __raw_readl(SH7751_WCR3); |
| 161 |
pci_write_reg(chan, word, SH4_PCIWCR3); |
| 162 |
word = __raw_readl(SH7751_MCR); |
| 163 |
pci_write_reg(chan, word, SH4_PCIMCR); |
| 164 |
|
| 165 |
/* NOTE: I'm ignoring the PCI error IRQs for now.. |
| 166 |
* TODO: add support for the internal error interrupts and |
| 167 |
* DMA interrupts... |
| 168 |
*/ |
| 169 |
|
| 170 |
pci_fixup_pcic(chan); |
| 171 |
|
| 172 |
/* SH7751 init done, set central function init complete */ |
| 173 |
/* use round robin mode to stop a device starving/overruning */ |
| 174 |
word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_ARBM; |
| 175 |
pci_write_reg(chan, word, SH4_PCICR); |
| 176 |
|
| 177 |
return register_pci_controller(chan); |
| 178 |
} |
| 179 |
arch_initcall(sh7751_pci_init); |