| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
#include <linux/kernel.h> |
| 3 |
#include <linux/types.h> |
| 4 |
#include <linux/init.h> |
| 5 |
#include <linux/delay.h> |
| 6 |
#include <linux/pci.h> |
| 7 |
#include <linux/io.h> |
| 8 |
#include <linux/sh_intc.h> |
| 9 |
#include "pci-sh4.h" |
| 10 |
|
| 11 |
int pcibios_map_platform_irq(const struct pci_dev *, u8 slot, u8 pin) |
| 12 |
{ |
| 13 |
switch (slot) { |
| 14 |
case 0: return evt2irq(0x3a0); |
| 15 |
case 1: return evt2irq(0x3a0); /* AMD Ethernet controller */ |
| 16 |
case 2: return -1; |
| 17 |
case 3: return -1; |
| 18 |
case 4: return -1; |
| 19 |
default: |
| 20 |
printk("PCI: Bad IRQ mapping request for slot %d\n", slot); |
| 21 |
return -1; |
| 22 |
} |
| 23 |
} |
| 24 |
|
| 25 |
#define PCIMCR_MRSET_OFF 0xBFFFFFFF |
| 26 |
#define PCIMCR_RFSH_OFF 0xFFFFFFFB |
| 27 |
|
| 28 |
/* |
| 29 |
* Only long word accesses of the PCIC's internal local registers and the |
| 30 |
* configuration registers from the CPU is supported. |
| 31 |
*/ |
| 32 |
#define PCIC_WRITE(x,v) writel((v), PCI_REG(x)) |
| 33 |
#define PCIC_READ(x) readl(PCI_REG(x)) |
| 34 |
|
| 35 |
/* |
| 36 |
* Description: This function sets up and initializes the pcic, sets |
| 37 |
* up the BARS, maps the DRAM into the address space etc, etc. |
| 38 |
*/ |
| 39 |
int pci_fixup_pcic(struct pci_channel *chan) |
| 40 |
{ |
| 41 |
unsigned long bcr1, wcr1, wcr2, wcr3, mcr; |
| 42 |
unsigned short bcr2; |
| 43 |
|
| 44 |
/* |
| 45 |
* Initialize the slave bus controller on the pcic. The values used |
| 46 |
* here should not be hardcoded, but they should be taken from the bsc |
| 47 |
* on the processor, to make this function as generic as possible. |
| 48 |
* (i.e. Another sbc may usr different SDRAM timing settings -- in order |
| 49 |
* for the pcic to work, its settings need to be exactly the same.) |
| 50 |
*/ |
| 51 |
bcr1 = (*(volatile unsigned long*)(SH7751_BCR1)); |
| 52 |
bcr2 = (*(volatile unsigned short*)(SH7751_BCR2)); |
| 53 |
wcr1 = (*(volatile unsigned long*)(SH7751_WCR1)); |
| 54 |
wcr2 = (*(volatile unsigned long*)(SH7751_WCR2)); |
| 55 |
wcr3 = (*(volatile unsigned long*)(SH7751_WCR3)); |
| 56 |
mcr = (*(volatile unsigned long*)(SH7751_MCR)); |
| 57 |
|
| 58 |
bcr1 = bcr1 | 0x00080000; /* Enable Bit 19, BREQEN */ |
| 59 |
(*(volatile unsigned long*)(SH7751_BCR1)) = bcr1; |
| 60 |
|
| 61 |
bcr1 = bcr1 | 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */ |
| 62 |
PCIC_WRITE(SH7751_PCIBCR1, bcr1); /* PCIC BCR1 */ |
| 63 |
PCIC_WRITE(SH7751_PCIBCR2, bcr2); /* PCIC BCR2 */ |
| 64 |
PCIC_WRITE(SH7751_PCIWCR1, wcr1); /* PCIC WCR1 */ |
| 65 |
PCIC_WRITE(SH7751_PCIWCR2, wcr2); /* PCIC WCR2 */ |
| 66 |
PCIC_WRITE(SH7751_PCIWCR3, wcr3); /* PCIC WCR3 */ |
| 67 |
mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF; |
| 68 |
PCIC_WRITE(SH7751_PCIMCR, mcr); /* PCIC MCR */ |
| 69 |
|
| 70 |
|
| 71 |
/* Enable all interrupts, so we know what to fix */ |
| 72 |
PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff); |
| 73 |
PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f); |
| 74 |
|
| 75 |
/* Set up standard PCI config registers */ |
| 76 |
PCIC_WRITE(SH7751_PCICONF1, 0xF39000C7); /* Bus Master, Mem & I/O access */ |
| 77 |
PCIC_WRITE(SH7751_PCICONF2, 0x00000000); /* PCI Class code & Revision ID */ |
| 78 |
PCIC_WRITE(SH7751_PCICONF4, 0xab000001); /* PCI I/O address (local regs) */ |
| 79 |
PCIC_WRITE(SH7751_PCICONF5, 0x0c000000); /* PCI MEM address (local RAM) */ |
| 80 |
PCIC_WRITE(SH7751_PCICONF6, 0xd0000000); /* PCI MEM address (unused) */ |
| 81 |
PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */ |
| 82 |
PCIC_WRITE(SH7751_PCILSR0, 0x03f00000); /* MEM (full 64M exposed) */ |
| 83 |
PCIC_WRITE(SH7751_PCILSR1, 0x00000000); /* MEM (unused) */ |
| 84 |
PCIC_WRITE(SH7751_PCILAR0, 0x0c000000); /* MEM (direct map from PCI) */ |
| 85 |
PCIC_WRITE(SH7751_PCILAR1, 0x00000000); /* MEM (unused) */ |
| 86 |
|
| 87 |
/* Now turn it on... */ |
| 88 |
PCIC_WRITE(SH7751_PCICR, 0xa5000001); |
| 89 |
|
| 90 |
/* |
| 91 |
* Set PCIMBR and PCIIOBR here, assuming a single window |
| 92 |
* (16M MEM, 256K IO) is enough. If a larger space is |
| 93 |
* needed, the readx/writex and inx/outx functions will |
| 94 |
* have to do more (e.g. setting registers for each call). |
| 95 |
*/ |
| 96 |
|
| 97 |
/* |
| 98 |
* Set the MBR so PCI address is one-to-one with window, |
| 99 |
* meaning all calls go straight through... use BUG_ON to |
| 100 |
* catch erroneous assumption. |
| 101 |
*/ |
| 102 |
BUG_ON(chan->resources[1].start != SH7751_PCI_MEMORY_BASE); |
| 103 |
|
| 104 |
PCIC_WRITE(SH7751_PCIMBR, chan->resources[1].start); |
| 105 |
|
| 106 |
/* Set IOBR for window containing area specified in pci.h */ |
| 107 |
PCIC_WRITE(SH7751_PCIIOBR, (chan->resources[0].start & SH7751_PCIIOBR_MASK)); |
| 108 |
|
| 109 |
/* All done, may as well say so... */ |
| 110 |
printk("SH7751 PCI: Finished initialization of the PCI controller\n"); |
| 111 |
|
| 112 |
return 1; |
| 113 |
} |