| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* linux/arch/sh/boards/magicpanel/setup.c |
| 4 |
* |
| 5 |
* Copyright (C) 2007 Markus Brunner, Mark Jonas |
| 6 |
* |
| 7 |
* Magic Panel Release 2 board setup |
| 8 |
*/ |
| 9 |
#include <linux/init.h> |
| 10 |
#include <linux/irq.h> |
| 11 |
#include <linux/platform_device.h> |
| 12 |
#include <linux/delay.h> |
| 13 |
#include <linux/gpio.h> |
| 14 |
#include <linux/regulator/fixed.h> |
| 15 |
#include <linux/regulator/machine.h> |
| 16 |
#include <linux/smsc911x.h> |
| 17 |
#include <linux/mtd/mtd.h> |
| 18 |
#include <linux/mtd/partitions.h> |
| 19 |
#include <linux/mtd/physmap.h> |
| 20 |
#include <linux/mtd/map.h> |
| 21 |
#include <linux/sh_intc.h> |
| 22 |
#include <mach/magicpanelr2.h> |
| 23 |
#include <asm/heartbeat.h> |
| 24 |
#include <cpu/gpio.h> |
| 25 |
#include <cpu/sh7720.h> |
| 26 |
|
| 27 |
/* Dummy supplies, where voltage doesn't matter */ |
| 28 |
static struct regulator_consumer_supply dummy_supplies[] = { |
| 29 |
REGULATOR_SUPPLY("vddvario", "smsc911x"), |
| 30 |
REGULATOR_SUPPLY("vdd33a", "smsc911x"), |
| 31 |
}; |
| 32 |
|
| 33 |
#define LAN9115_READY (__raw_readl(0xA8000084UL) & 0x00000001UL) |
| 34 |
|
| 35 |
/* Wait until reset finished. Timeout is 100ms. */ |
| 36 |
static int __init ethernet_reset_finished(void) |
| 37 |
{ |
| 38 |
int i; |
| 39 |
|
| 40 |
if (LAN9115_READY) |
| 41 |
return 1; |
| 42 |
|
| 43 |
for (i = 0; i < 10; ++i) { |
| 44 |
mdelay(10); |
| 45 |
if (LAN9115_READY) |
| 46 |
return 1; |
| 47 |
} |
| 48 |
|
| 49 |
return 0; |
| 50 |
} |
| 51 |
|
| 52 |
static void __init reset_ethernet(void) |
| 53 |
{ |
| 54 |
/* PMDR: LAN_RESET=on */ |
| 55 |
CLRBITS_OUTB(0x10, PORT_PMDR); |
| 56 |
|
| 57 |
udelay(200); |
| 58 |
|
| 59 |
/* PMDR: LAN_RESET=off */ |
| 60 |
SETBITS_OUTB(0x10, PORT_PMDR); |
| 61 |
} |
| 62 |
|
| 63 |
static void __init setup_chip_select(void) |
| 64 |
{ |
| 65 |
/* CS2: LAN (0x08000000 - 0x0bffffff) */ |
| 66 |
/* no idle cycles, normal space, 8 bit data bus */ |
| 67 |
__raw_writel(0x36db0400, CS2BCR); |
| 68 |
/* (SW:1.5 WR:3 HW:1.5), ext. wait */ |
| 69 |
__raw_writel(0x000003c0, CS2WCR); |
| 70 |
|
| 71 |
/* CS4: CAN1 (0xb0000000 - 0xb3ffffff) */ |
| 72 |
/* no idle cycles, normal space, 8 bit data bus */ |
| 73 |
__raw_writel(0x00000200, CS4BCR); |
| 74 |
/* (SW:1.5 WR:3 HW:1.5), ext. wait */ |
| 75 |
__raw_writel(0x00100981, CS4WCR); |
| 76 |
|
| 77 |
/* CS5a: CAN2 (0xb4000000 - 0xb5ffffff) */ |
| 78 |
/* no idle cycles, normal space, 8 bit data bus */ |
| 79 |
__raw_writel(0x00000200, CS5ABCR); |
| 80 |
/* (SW:1.5 WR:3 HW:1.5), ext. wait */ |
| 81 |
__raw_writel(0x00100981, CS5AWCR); |
| 82 |
|
| 83 |
/* CS5b: CAN3 (0xb6000000 - 0xb7ffffff) */ |
| 84 |
/* no idle cycles, normal space, 8 bit data bus */ |
| 85 |
__raw_writel(0x00000200, CS5BBCR); |
| 86 |
/* (SW:1.5 WR:3 HW:1.5), ext. wait */ |
| 87 |
__raw_writel(0x00100981, CS5BWCR); |
| 88 |
|
| 89 |
/* CS6a: Rotary (0xb8000000 - 0xb9ffffff) */ |
| 90 |
/* no idle cycles, normal space, 8 bit data bus */ |
| 91 |
__raw_writel(0x00000200, CS6ABCR); |
| 92 |
/* (SW:1.5 WR:3 HW:1.5), no ext. wait */ |
| 93 |
__raw_writel(0x001009C1, CS6AWCR); |
| 94 |
} |
| 95 |
|
| 96 |
static void __init setup_port_multiplexing(void) |
| 97 |
{ |
| 98 |
/* A7 GPO(LED8); A6 GPO(LED7); A5 GPO(LED6); A4 GPO(LED5); |
| 99 |
* A3 GPO(LED4); A2 GPO(LED3); A1 GPO(LED2); A0 GPO(LED1); |
| 100 |
*/ |
| 101 |
__raw_writew(0x5555, PORT_PACR); /* 01 01 01 01 01 01 01 01 */ |
| 102 |
|
| 103 |
/* B7 GPO(RST4); B6 GPO(RST3); B5 GPO(RST2); B4 GPO(RST1); |
| 104 |
* B3 GPO(PB3); B2 GPO(PB2); B1 GPO(PB1); B0 GPO(PB0); |
| 105 |
*/ |
| 106 |
__raw_writew(0x5555, PORT_PBCR); /* 01 01 01 01 01 01 01 01 */ |
| 107 |
|
| 108 |
/* C7 GPO(PC7); C6 GPO(PC6); C5 GPO(PC5); C4 GPO(PC4); |
| 109 |
* C3 LCD_DATA3; C2 LCD_DATA2; C1 LCD_DATA1; C0 LCD_DATA0; |
| 110 |
*/ |
| 111 |
__raw_writew(0x5500, PORT_PCCR); /* 01 01 01 01 00 00 00 00 */ |
| 112 |
|
| 113 |
/* D7 GPO(PD7); D6 GPO(PD6); D5 GPO(PD5); D4 GPO(PD4); |
| 114 |
* D3 GPO(PD3); D2 GPO(PD2); D1 GPO(PD1); D0 GPO(PD0); |
| 115 |
*/ |
| 116 |
__raw_writew(0x5555, PORT_PDCR); /* 01 01 01 01 01 01 01 01 */ |
| 117 |
|
| 118 |
/* E7 (x); E6 GPI(nu); E5 GPI(nu); E4 LCD_M_DISP; |
| 119 |
* E3 LCD_CL1; E2 LCD_CL2; E1 LCD_DON; E0 LCD_FLM; |
| 120 |
*/ |
| 121 |
__raw_writew(0x3C00, PORT_PECR); /* 00 11 11 00 00 00 00 00 */ |
| 122 |
|
| 123 |
/* F7 (x); F6 DA1(VLCD); F5 DA0(nc); F4 AN3; |
| 124 |
* F3 AN2(MID_AD); F2 AN1(EARTH_AD); F1 AN0(TEMP); F0 GPI+(nc); |
| 125 |
*/ |
| 126 |
__raw_writew(0x0002, PORT_PFCR); /* 00 00 00 00 00 00 00 10 */ |
| 127 |
|
| 128 |
/* G7 (x); G6 IRQ5(TOUCH_BUSY); G5 IRQ4(TOUCH_IRQ); G4 GPI(KEY2); |
| 129 |
* G3 GPI(KEY1); G2 GPO(LED11); G1 GPO(LED10); G0 GPO(LED9); |
| 130 |
*/ |
| 131 |
__raw_writew(0x03D5, PORT_PGCR); /* 00 00 00 11 11 01 01 01 */ |
| 132 |
|
| 133 |
/* H7 (x); H6 /RAS(BRAS); H5 /CAS(BCAS); H4 CKE(BCKE); |
| 134 |
* H3 GPO(EARTH_OFF); H2 GPO(EARTH_TEST); H1 USB2_PWR; H0 USB1_PWR; |
| 135 |
*/ |
| 136 |
__raw_writew(0x0050, PORT_PHCR); /* 00 00 00 00 01 01 00 00 */ |
| 137 |
|
| 138 |
/* J7 (x); J6 AUDCK; J5 ASEBRKAK; J4 AUDATA3; |
| 139 |
* J3 AUDATA2; J2 AUDATA1; J1 AUDATA0; J0 AUDSYNC; |
| 140 |
*/ |
| 141 |
__raw_writew(0x0000, PORT_PJCR); /* 00 00 00 00 00 00 00 00 */ |
| 142 |
|
| 143 |
/* K7 (x); K6 (x); K5 (x); K4 (x); |
| 144 |
* K3 PINT7(/PWR2); K2 PINT6(/PWR1); K1 PINT5(nu); K0 PINT4(FLASH_READY) |
| 145 |
*/ |
| 146 |
__raw_writew(0x00FF, PORT_PKCR); /* 00 00 00 00 11 11 11 11 */ |
| 147 |
|
| 148 |
/* L7 TRST; L6 TMS; L5 TDO; L4 TDI; |
| 149 |
* L3 TCK; L2 (x); L1 (x); L0 (x); |
| 150 |
*/ |
| 151 |
__raw_writew(0x0000, PORT_PLCR); /* 00 00 00 00 00 00 00 00 */ |
| 152 |
|
| 153 |
/* M7 GPO(CURRENT_SINK); M6 GPO(PWR_SWITCH); M5 GPO(LAN_SPEED); |
| 154 |
* M4 GPO(LAN_RESET); M3 GPO(BUZZER); M2 GPO(LCD_BL); |
| 155 |
* M1 CS5B(CAN3_CS); M0 GPI+(nc); |
| 156 |
*/ |
| 157 |
__raw_writew(0x5552, PORT_PMCR); /* 01 01 01 01 01 01 00 10 */ |
| 158 |
|
| 159 |
/* CURRENT_SINK=off, PWR_SWITCH=off, LAN_SPEED=100MBit, |
| 160 |
* LAN_RESET=off, BUZZER=off, LCD_BL=off |
| 161 |
*/ |
| 162 |
#if CONFIG_SH_MAGIC_PANEL_R2_VERSION == 2 |
| 163 |
__raw_writeb(0x30, PORT_PMDR); |
| 164 |
#elif CONFIG_SH_MAGIC_PANEL_R2_VERSION == 3 |
| 165 |
__raw_writeb(0xF0, PORT_PMDR); |
| 166 |
#else |
| 167 |
#error Unknown revision of PLATFORM_MP_R2 |
| 168 |
#endif |
| 169 |
|
| 170 |
/* P7 (x); P6 (x); P5 (x); |
| 171 |
* P4 GPO(nu); P3 IRQ3(LAN_IRQ); P2 IRQ2(CAN3_IRQ); |
| 172 |
* P1 IRQ1(CAN2_IRQ); P0 IRQ0(CAN1_IRQ) |
| 173 |
*/ |
| 174 |
__raw_writew(0x0100, PORT_PPCR); /* 00 00 00 01 00 00 00 00 */ |
| 175 |
__raw_writeb(0x10, PORT_PPDR); |
| 176 |
|
| 177 |
/* R7 A25; R6 A24; R5 A23; R4 A22; |
| 178 |
* R3 A21; R2 A20; R1 A19; R0 A0; |
| 179 |
*/ |
| 180 |
gpio_request(GPIO_FN_A25, NULL); |
| 181 |
gpio_request(GPIO_FN_A24, NULL); |
| 182 |
gpio_request(GPIO_FN_A23, NULL); |
| 183 |
gpio_request(GPIO_FN_A22, NULL); |
| 184 |
gpio_request(GPIO_FN_A21, NULL); |
| 185 |
gpio_request(GPIO_FN_A20, NULL); |
| 186 |
gpio_request(GPIO_FN_A19, NULL); |
| 187 |
gpio_request(GPIO_FN_A0, NULL); |
| 188 |
|
| 189 |
/* S7 (x); S6 (x); S5 (x); S4 GPO(EEPROM_CS2); |
| 190 |
* S3 GPO(EEPROM_CS1); S2 SIOF0_TXD; S1 SIOF0_RXD; S0 SIOF0_SCK; |
| 191 |
*/ |
| 192 |
__raw_writew(0x0140, PORT_PSCR); /* 00 00 00 01 01 00 00 00 */ |
| 193 |
|
| 194 |
/* T7 (x); T6 (x); T5 (x); T4 COM1_CTS; |
| 195 |
* T3 COM1_RTS; T2 COM1_TXD; T1 COM1_RXD; T0 GPO(WDOG) |
| 196 |
*/ |
| 197 |
__raw_writew(0x0001, PORT_PTCR); /* 00 00 00 00 00 00 00 01 */ |
| 198 |
|
| 199 |
/* U7 (x); U6 (x); U5 (x); U4 GPI+(/AC_FAULT); |
| 200 |
* U3 GPO(TOUCH_CS); U2 TOUCH_TXD; U1 TOUCH_RXD; U0 TOUCH_SCK; |
| 201 |
*/ |
| 202 |
__raw_writew(0x0240, PORT_PUCR); /* 00 00 00 10 01 00 00 00 */ |
| 203 |
|
| 204 |
/* V7 (x); V6 (x); V5 (x); V4 GPO(MID2); |
| 205 |
* V3 GPO(MID1); V2 CARD_TxD; V1 CARD_RxD; V0 GPI+(/BAT_FAULT); |
| 206 |
*/ |
| 207 |
__raw_writew(0x0142, PORT_PVCR); /* 00 00 00 01 01 00 00 10 */ |
| 208 |
} |
| 209 |
|
| 210 |
static void __init mpr2_setup(char **cmdline_p) |
| 211 |
{ |
| 212 |
/* set Pin Select Register A: |
| 213 |
* /PCC_CD1, /PCC_CD2, PCC_BVD1, PCC_BVD2, |
| 214 |
* /IOIS16, IRQ4, IRQ5, USB1d_SUSPEND |
| 215 |
*/ |
| 216 |
__raw_writew(0xAABC, PORT_PSELA); |
| 217 |
/* set Pin Select Register B: |
| 218 |
* /SCIF0_RTS, /SCIF0_CTS, LCD_VCPWC, |
| 219 |
* LCD_VEPWC, IIC_SDA, IIC_SCL, Reserved |
| 220 |
*/ |
| 221 |
__raw_writew(0x3C00, PORT_PSELB); |
| 222 |
/* set Pin Select Register C: |
| 223 |
* SIOF1_SCK, SIOF1_RxD, SCIF1_RxD, SCIF1_TxD, Reserved |
| 224 |
*/ |
| 225 |
__raw_writew(0x0000, PORT_PSELC); |
| 226 |
/* set Pin Select Register D: Reserved, SIOF1_TxD, Reserved, SIOF1_MCLK, |
| 227 |
* Reserved, SIOF1_SYNC, Reserved, SCIF1_SCK, Reserved |
| 228 |
*/ |
| 229 |
__raw_writew(0x0000, PORT_PSELD); |
| 230 |
/* set USB TxRx Control: Reserved, DRV, Reserved, USB_TRANS, USB_SEL */ |
| 231 |
__raw_writew(0x0101, PORT_UTRCTL); |
| 232 |
/* set USB Clock Control: USSCS, USSTB, Reserved (HighByte always A5) */ |
| 233 |
__raw_writew(0xA5C0, PORT_UCLKCR_W); |
| 234 |
|
| 235 |
setup_chip_select(); |
| 236 |
|
| 237 |
setup_port_multiplexing(); |
| 238 |
|
| 239 |
reset_ethernet(); |
| 240 |
|
| 241 |
printk(KERN_INFO "Magic Panel Release 2 A.%i\n", |
| 242 |
CONFIG_SH_MAGIC_PANEL_R2_VERSION); |
| 243 |
|
| 244 |
if (ethernet_reset_finished() == 0) |
| 245 |
printk(KERN_WARNING "Ethernet not ready\n"); |
| 246 |
} |
| 247 |
|
| 248 |
static struct resource smsc911x_resources[] = { |
| 249 |
[0] = { |
| 250 |
.start = 0xa8000000, |
| 251 |
.end = 0xabffffff, |
| 252 |
.flags = IORESOURCE_MEM, |
| 253 |
}, |
| 254 |
[1] = { |
| 255 |
.start = evt2irq(0x660), |
| 256 |
.end = evt2irq(0x660), |
| 257 |
.flags = IORESOURCE_IRQ, |
| 258 |
}, |
| 259 |
}; |
| 260 |
|
| 261 |
static struct smsc911x_platform_config smsc911x_config = { |
| 262 |
.phy_interface = PHY_INTERFACE_MODE_MII, |
| 263 |
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, |
| 264 |
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, |
| 265 |
.flags = SMSC911X_USE_32BIT, |
| 266 |
}; |
| 267 |
|
| 268 |
static struct platform_device smsc911x_device = { |
| 269 |
.name = "smsc911x", |
| 270 |
.id = -1, |
| 271 |
.num_resources = ARRAY_SIZE(smsc911x_resources), |
| 272 |
.resource = smsc911x_resources, |
| 273 |
.dev = { |
| 274 |
.platform_data = &smsc911x_config, |
| 275 |
}, |
| 276 |
}; |
| 277 |
|
| 278 |
static struct resource heartbeat_resources[] = { |
| 279 |
[0] = { |
| 280 |
.start = PA_LED, |
| 281 |
.end = PA_LED, |
| 282 |
.flags = IORESOURCE_MEM, |
| 283 |
}, |
| 284 |
}; |
| 285 |
|
| 286 |
static struct heartbeat_data heartbeat_data = { |
| 287 |
.flags = HEARTBEAT_INVERTED, |
| 288 |
}; |
| 289 |
|
| 290 |
static struct platform_device heartbeat_device = { |
| 291 |
.name = "heartbeat", |
| 292 |
.id = -1, |
| 293 |
.dev = { |
| 294 |
.platform_data = &heartbeat_data, |
| 295 |
}, |
| 296 |
.num_resources = ARRAY_SIZE(heartbeat_resources), |
| 297 |
.resource = heartbeat_resources, |
| 298 |
}; |
| 299 |
|
| 300 |
static struct mtd_partition mpr2_partitions[] = { |
| 301 |
/* Reserved for bootloader, read-only */ |
| 302 |
{ |
| 303 |
.name = "Bootloader", |
| 304 |
.offset = 0x00000000UL, |
| 305 |
.size = MPR2_MTD_BOOTLOADER_SIZE, |
| 306 |
.mask_flags = MTD_WRITEABLE, |
| 307 |
}, |
| 308 |
/* Reserved for kernel image */ |
| 309 |
{ |
| 310 |
.name = "Kernel", |
| 311 |
.offset = MTDPART_OFS_NXTBLK, |
| 312 |
.size = MPR2_MTD_KERNEL_SIZE, |
| 313 |
}, |
| 314 |
/* Rest is used for Flash FS */ |
| 315 |
{ |
| 316 |
.name = "Flash_FS", |
| 317 |
.offset = MTDPART_OFS_NXTBLK, |
| 318 |
.size = MTDPART_SIZ_FULL, |
| 319 |
} |
| 320 |
}; |
| 321 |
|
| 322 |
static struct physmap_flash_data flash_data = { |
| 323 |
.parts = mpr2_partitions, |
| 324 |
.nr_parts = ARRAY_SIZE(mpr2_partitions), |
| 325 |
.width = 2, |
| 326 |
}; |
| 327 |
|
| 328 |
static struct resource flash_resource = { |
| 329 |
.start = 0x00000000, |
| 330 |
.end = 0x2000000UL, |
| 331 |
.flags = IORESOURCE_MEM, |
| 332 |
}; |
| 333 |
|
| 334 |
static struct platform_device flash_device = { |
| 335 |
.name = "physmap-flash", |
| 336 |
.id = -1, |
| 337 |
.resource = &flash_resource, |
| 338 |
.num_resources = 1, |
| 339 |
.dev = { |
| 340 |
.platform_data = &flash_data, |
| 341 |
}, |
| 342 |
}; |
| 343 |
|
| 344 |
/* |
| 345 |
* Add all resources to the platform_device |
| 346 |
*/ |
| 347 |
|
| 348 |
static struct platform_device *mpr2_devices[] __initdata = { |
| 349 |
&heartbeat_device, |
| 350 |
&smsc911x_device, |
| 351 |
&flash_device, |
| 352 |
}; |
| 353 |
|
| 354 |
|
| 355 |
static int __init mpr2_devices_setup(void) |
| 356 |
{ |
| 357 |
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); |
| 358 |
|
| 359 |
return platform_add_devices(mpr2_devices, ARRAY_SIZE(mpr2_devices)); |
| 360 |
} |
| 361 |
device_initcall(mpr2_devices_setup); |
| 362 |
|
| 363 |
/* |
| 364 |
* Initialize IRQ setting |
| 365 |
*/ |
| 366 |
static void __init init_mpr2_IRQ(void) |
| 367 |
{ |
| 368 |
plat_irq_setup_pins(IRQ_MODE_IRQ); /* install handlers for IRQ0-5 */ |
| 369 |
|
| 370 |
irq_set_irq_type(evt2irq(0x600), IRQ_TYPE_LEVEL_LOW); /* IRQ0 CAN1 */ |
| 371 |
irq_set_irq_type(evt2irq(0x620), IRQ_TYPE_LEVEL_LOW); /* IRQ1 CAN2 */ |
| 372 |
irq_set_irq_type(evt2irq(0x640), IRQ_TYPE_LEVEL_LOW); /* IRQ2 CAN3 */ |
| 373 |
irq_set_irq_type(evt2irq(0x660), IRQ_TYPE_LEVEL_LOW); /* IRQ3 SMSC9115 */ |
| 374 |
irq_set_irq_type(evt2irq(0x680), IRQ_TYPE_EDGE_RISING); /* IRQ4 touchscreen */ |
| 375 |
irq_set_irq_type(evt2irq(0x6a0), IRQ_TYPE_EDGE_FALLING); /* IRQ5 touchscreen */ |
| 376 |
|
| 377 |
intc_set_priority(evt2irq(0x600), 13); /* IRQ0 CAN1 */ |
| 378 |
intc_set_priority(evt2irq(0x620), 13); /* IRQ0 CAN2 */ |
| 379 |
intc_set_priority(evt2irq(0x640), 13); /* IRQ0 CAN3 */ |
| 380 |
intc_set_priority(evt2irq(0x660), 6); /* IRQ3 SMSC9115 */ |
| 381 |
} |
| 382 |
|
| 383 |
/* |
| 384 |
* The Machine Vector |
| 385 |
*/ |
| 386 |
|
| 387 |
static struct sh_machine_vector mv_mpr2 __initmv = { |
| 388 |
.mv_name = "mpr2", |
| 389 |
.mv_setup = mpr2_setup, |
| 390 |
.mv_init_irq = init_mpr2_IRQ, |
| 391 |
}; |