| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* ALPHAPROJECT AP-SH4AD-0A Support. |
| 4 |
* |
| 5 |
* Copyright (C) 2010 ALPHAPROJECT Co.,Ltd. |
| 6 |
* Copyright (C) 2010 Matt Fleming |
| 7 |
* Copyright (C) 2010 Paul Mundt |
| 8 |
*/ |
| 9 |
#include <linux/init.h> |
| 10 |
#include <linux/platform_device.h> |
| 11 |
#include <linux/io.h> |
| 12 |
#include <linux/regulator/fixed.h> |
| 13 |
#include <linux/regulator/machine.h> |
| 14 |
#include <linux/smsc911x.h> |
| 15 |
#include <linux/irq.h> |
| 16 |
#include <linux/clk.h> |
| 17 |
#include <asm/machvec.h> |
| 18 |
#include <linux/sizes.h> |
| 19 |
|
| 20 |
/* Dummy supplies, where voltage doesn't matter */ |
| 21 |
static struct regulator_consumer_supply dummy_supplies[] = { |
| 22 |
REGULATOR_SUPPLY("vddvario", "smsc911x"), |
| 23 |
REGULATOR_SUPPLY("vdd33a", "smsc911x"), |
| 24 |
}; |
| 25 |
|
| 26 |
static struct resource smsc911x_resources[] = { |
| 27 |
[0] = { |
| 28 |
.name = "smsc911x-memory", |
| 29 |
.start = 0xA4000000, |
| 30 |
.end = 0xA4000000 + SZ_256 - 1, |
| 31 |
.flags = IORESOURCE_MEM, |
| 32 |
}, |
| 33 |
[1] = { |
| 34 |
.name = "smsc911x-irq", |
| 35 |
.start = evt2irq(0x200), |
| 36 |
.end = evt2irq(0x200), |
| 37 |
.flags = IORESOURCE_IRQ, |
| 38 |
}, |
| 39 |
}; |
| 40 |
|
| 41 |
static struct smsc911x_platform_config smsc911x_config = { |
| 42 |
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, |
| 43 |
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, |
| 44 |
.flags = SMSC911X_USE_16BIT, |
| 45 |
.phy_interface = PHY_INTERFACE_MODE_MII, |
| 46 |
}; |
| 47 |
|
| 48 |
static struct platform_device smsc911x_device = { |
| 49 |
.name = "smsc911x", |
| 50 |
.id = -1, |
| 51 |
.num_resources = ARRAY_SIZE(smsc911x_resources), |
| 52 |
.resource = smsc911x_resources, |
| 53 |
.dev = { |
| 54 |
.platform_data = &smsc911x_config, |
| 55 |
}, |
| 56 |
}; |
| 57 |
|
| 58 |
static struct platform_device *apsh4ad0a_devices[] __initdata = { |
| 59 |
&smsc911x_device, |
| 60 |
}; |
| 61 |
|
| 62 |
static int __init apsh4ad0a_devices_setup(void) |
| 63 |
{ |
| 64 |
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); |
| 65 |
|
| 66 |
return platform_add_devices(apsh4ad0a_devices, |
| 67 |
ARRAY_SIZE(apsh4ad0a_devices)); |
| 68 |
} |
| 69 |
device_initcall(apsh4ad0a_devices_setup); |
| 70 |
|
| 71 |
static int apsh4ad0a_mode_pins(void) |
| 72 |
{ |
| 73 |
int value = 0; |
| 74 |
|
| 75 |
/* These are the factory default settings of SW1 and SW2. |
| 76 |
* If you change these dip switches then you will need to |
| 77 |
* adjust the values below as well. |
| 78 |
*/ |
| 79 |
value |= MODE_PIN0; /* Clock Mode 3 */ |
| 80 |
value |= MODE_PIN1; |
| 81 |
value &= ~MODE_PIN2; |
| 82 |
value &= ~MODE_PIN3; |
| 83 |
value &= ~MODE_PIN4; /* 16-bit Area0 bus width */ |
| 84 |
value |= MODE_PIN5; |
| 85 |
value |= MODE_PIN6; |
| 86 |
value |= MODE_PIN7; /* Normal mode */ |
| 87 |
value |= MODE_PIN8; /* Little Endian */ |
| 88 |
value |= MODE_PIN9; /* Crystal resonator */ |
| 89 |
value &= ~MODE_PIN10; /* 29-bit address mode */ |
| 90 |
value &= ~MODE_PIN11; /* PCI-E Root port */ |
| 91 |
value &= ~MODE_PIN12; /* 4 lane + 1 lane */ |
| 92 |
value |= MODE_PIN13; /* AUD Enable */ |
| 93 |
value &= ~MODE_PIN14; /* Normal Operation */ |
| 94 |
|
| 95 |
return value; |
| 96 |
} |
| 97 |
|
| 98 |
static int apsh4ad0a_clk_init(void) |
| 99 |
{ |
| 100 |
struct clk *clk; |
| 101 |
int ret; |
| 102 |
|
| 103 |
clk = clk_get(NULL, "extal"); |
| 104 |
if (IS_ERR(clk)) |
| 105 |
return PTR_ERR(clk); |
| 106 |
ret = clk_set_rate(clk, 33333000); |
| 107 |
clk_put(clk); |
| 108 |
|
| 109 |
return ret; |
| 110 |
} |
| 111 |
|
| 112 |
/* Initialize the board */ |
| 113 |
static void __init apsh4ad0a_setup(char **cmdline_p) |
| 114 |
{ |
| 115 |
pr_info("Alpha Project AP-SH4AD-0A support:\n"); |
| 116 |
} |
| 117 |
|
| 118 |
static void __init apsh4ad0a_init_irq(void) |
| 119 |
{ |
| 120 |
plat_irq_setup_pins(IRQ_MODE_IRQ3210); |
| 121 |
} |
| 122 |
|
| 123 |
/* |
| 124 |
* The Machine Vector |
| 125 |
*/ |
| 126 |
static struct sh_machine_vector mv_apsh4ad0a __initmv = { |
| 127 |
.mv_name = "AP-SH4AD-0A", |
| 128 |
.mv_setup = apsh4ad0a_setup, |
| 129 |
.mv_mode_pins = apsh4ad0a_mode_pins, |
| 130 |
.mv_clk_init = apsh4ad0a_clk_init, |
| 131 |
.mv_init_irq = apsh4ad0a_init_irq, |
| 132 |
}; |