| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include "jz4725b.dtsi" |
| 5 |
|
| 6 |
#include <dt-bindings/gpio/gpio.h> |
| 7 |
#include <dt-bindings/iio/adc/ingenic,adc.h> |
| 8 |
#include <dt-bindings/input/linux-event-codes.h> |
| 9 |
|
| 10 |
/ { |
| 11 |
compatible = "ylm,rs90", "ingenic,jz4725b"; |
| 12 |
model = "RS-90"; |
| 13 |
|
| 14 |
memory { |
| 15 |
device_type = "memory"; |
| 16 |
reg = <0x0 0x2000000>; |
| 17 |
}; |
| 18 |
|
| 19 |
reserved-memory { |
| 20 |
#address-cells = <1>; |
| 21 |
#size-cells = <1>; |
| 22 |
ranges; |
| 23 |
|
| 24 |
vmem: video-memory@1f00000 { |
| 25 |
compatible = "shared-dma-pool"; |
| 26 |
reg = <0x1f00000 0x100000>; |
| 27 |
reusable; |
| 28 |
}; |
| 29 |
}; |
| 30 |
|
| 31 |
vcc: regulator { |
| 32 |
compatible = "regulator-fixed"; |
| 33 |
|
| 34 |
regulator-name = "vcc"; |
| 35 |
regulaor-min-microvolt = <3300000>; |
| 36 |
regulaor-max-microvolt = <3300000>; |
| 37 |
regulator-always-on; |
| 38 |
}; |
| 39 |
|
| 40 |
backlight: backlight { |
| 41 |
compatible = "pwm-backlight"; |
| 42 |
pwms = <&pwm 3 40000 0>; |
| 43 |
|
| 44 |
brightness-levels = <0 16 32 48 64 80 112 144 192 255>; |
| 45 |
default-brightness-level = <8>; |
| 46 |
|
| 47 |
pinctrl-names = "default"; |
| 48 |
pinctrl-0 = <&pins_pwm3>; |
| 49 |
|
| 50 |
power-supply = <&vcc>; |
| 51 |
}; |
| 52 |
|
| 53 |
keys@0 { |
| 54 |
compatible = "gpio-keys"; |
| 55 |
|
| 56 |
key-0 { |
| 57 |
label = "D-pad up"; |
| 58 |
linux,code = <KEY_UP>; |
| 59 |
gpios = <&gpc 10 GPIO_ACTIVE_LOW>; |
| 60 |
}; |
| 61 |
|
| 62 |
key-1 { |
| 63 |
label = "D-pad down"; |
| 64 |
linux,code = <KEY_DOWN>; |
| 65 |
gpios = <&gpc 11 GPIO_ACTIVE_LOW>; |
| 66 |
}; |
| 67 |
|
| 68 |
key-2 { |
| 69 |
label = "D-pad left"; |
| 70 |
linux,code = <KEY_LEFT>; |
| 71 |
gpios = <&gpb 31 GPIO_ACTIVE_LOW>; |
| 72 |
}; |
| 73 |
|
| 74 |
key-3 { |
| 75 |
label = "D-pad right"; |
| 76 |
linux,code = <KEY_RIGHT>; |
| 77 |
gpios = <&gpd 21 GPIO_ACTIVE_LOW>; |
| 78 |
}; |
| 79 |
|
| 80 |
key-4 { |
| 81 |
label = "Button A"; |
| 82 |
linux,code = <KEY_LEFTCTRL>; |
| 83 |
gpios = <&gpc 31 GPIO_ACTIVE_LOW>; |
| 84 |
}; |
| 85 |
|
| 86 |
key-5 { |
| 87 |
label = "Button B"; |
| 88 |
linux,code = <KEY_LEFTALT>; |
| 89 |
gpios = <&gpc 30 GPIO_ACTIVE_LOW>; |
| 90 |
}; |
| 91 |
|
| 92 |
key-6 { |
| 93 |
label = "Right shoulder button"; |
| 94 |
linux,code = <KEY_BACKSPACE>; |
| 95 |
gpios = <&gpc 12 GPIO_ACTIVE_LOW>; |
| 96 |
debounce-interval = <10>; |
| 97 |
}; |
| 98 |
|
| 99 |
key-7 { |
| 100 |
label = "Start button"; |
| 101 |
linux,code = <KEY_ENTER>; |
| 102 |
gpios = <&gpd 17 GPIO_ACTIVE_LOW>; |
| 103 |
}; |
| 104 |
}; |
| 105 |
|
| 106 |
keys@1 { |
| 107 |
compatible = "adc-keys"; |
| 108 |
io-channels = <&adc INGENIC_ADC_AUX>; |
| 109 |
io-channel-names = "buttons"; |
| 110 |
keyup-threshold-microvolt = <1400000>; |
| 111 |
poll-interval = <30>; |
| 112 |
|
| 113 |
key@0 { |
| 114 |
label = "Left shoulder button"; |
| 115 |
linux,code = <KEY_TAB>; |
| 116 |
press-threshold-microvolt = <800000>; |
| 117 |
}; |
| 118 |
|
| 119 |
key@1 { |
| 120 |
label = "Select button"; |
| 121 |
linux,code = <KEY_ESC>; |
| 122 |
press-threshold-microvolt = <1100000>; |
| 123 |
}; |
| 124 |
}; |
| 125 |
|
| 126 |
amp: analog-amplifier { |
| 127 |
compatible = "simple-audio-amplifier"; |
| 128 |
enable-gpios = <&gpc 15 GPIO_ACTIVE_HIGH>; |
| 129 |
|
| 130 |
VCC-supply = <&vcc>; |
| 131 |
}; |
| 132 |
|
| 133 |
sound { |
| 134 |
compatible = "simple-audio-card"; |
| 135 |
|
| 136 |
simple-audio-card,name = "rs90-audio"; |
| 137 |
simple-audio-card,format = "i2s"; |
| 138 |
|
| 139 |
simple-audio-card,widgets = |
| 140 |
"Speaker", "Speaker", |
| 141 |
"Headphone", "Headphones"; |
| 142 |
simple-audio-card,routing = |
| 143 |
"INL", "LHPOUT", |
| 144 |
"INR", "RHPOUT", |
| 145 |
"Headphones", "LHPOUT", |
| 146 |
"Headphones", "RHPOUT", |
| 147 |
"Speaker", "OUTL", |
| 148 |
"Speaker", "OUTR"; |
| 149 |
simple-audio-card,pin-switches = "Speaker"; |
| 150 |
|
| 151 |
simple-audio-card,hp-det-gpios = <&gpd 16 GPIO_ACTIVE_LOW>; |
| 152 |
simple-audio-card,aux-devs = <&>; |
| 153 |
|
| 154 |
simple-audio-card,bitclock-master = <&dai_codec>; |
| 155 |
simple-audio-card,frame-master = <&dai_codec>; |
| 156 |
|
| 157 |
dai_cpu: simple-audio-card,cpu { |
| 158 |
sound-dai = <&aic>; |
| 159 |
}; |
| 160 |
|
| 161 |
dai_codec: simple-audio-card,codec { |
| 162 |
sound-dai = <&codec>; |
| 163 |
}; |
| 164 |
|
| 165 |
}; |
| 166 |
|
| 167 |
usb_phy: usb-phy { |
| 168 |
compatible = "usb-nop-xceiv"; |
| 169 |
#phy-cells = <0>; |
| 170 |
|
| 171 |
clocks = <&cgu JZ4725B_CLK_UDC_PHY>; |
| 172 |
clock-names = "main_clk"; |
| 173 |
vcc-supply = <&vcc>; |
| 174 |
}; |
| 175 |
|
| 176 |
panel { |
| 177 |
compatible = "sharp,ls020b1dd01d"; |
| 178 |
|
| 179 |
backlight = <&backlight>; |
| 180 |
power-supply = <&vcc>; |
| 181 |
|
| 182 |
port { |
| 183 |
panel_input: endpoint { |
| 184 |
remote-endpoint = <&panel_output>; |
| 185 |
}; |
| 186 |
}; |
| 187 |
}; |
| 188 |
}; |
| 189 |
|
| 190 |
&ext { |
| 191 |
clock-frequency = <12000000>; |
| 192 |
}; |
| 193 |
|
| 194 |
&rtc_dev { |
| 195 |
system-power-controller; |
| 196 |
}; |
| 197 |
|
| 198 |
&udc { |
| 199 |
phys = <&usb_phy>; |
| 200 |
}; |
| 201 |
|
| 202 |
&pinctrl { |
| 203 |
pins_mmc1: mmc1 { |
| 204 |
function = "mmc1"; |
| 205 |
groups = "mmc1-1bit"; |
| 206 |
}; |
| 207 |
|
| 208 |
pins_nemc: nemc { |
| 209 |
function = "nand"; |
| 210 |
groups = "nand-cs1", "nand-cle-ale", "nand-fre-fwe"; |
| 211 |
}; |
| 212 |
|
| 213 |
pins_pwm3: pwm3 { |
| 214 |
function = "pwm3"; |
| 215 |
groups = "pwm3"; |
| 216 |
bias-disable; |
| 217 |
}; |
| 218 |
|
| 219 |
pins_lcd: lcd { |
| 220 |
function = "lcd"; |
| 221 |
groups = "lcd-8bit", "lcd-16bit", "lcd-special"; |
| 222 |
}; |
| 223 |
}; |
| 224 |
|
| 225 |
&mmc0 { |
| 226 |
status = "disabled"; |
| 227 |
}; |
| 228 |
|
| 229 |
&mmc1 { |
| 230 |
bus-width = <1>; |
| 231 |
max-frequency = <48000000>; |
| 232 |
|
| 233 |
pinctrl-names = "default"; |
| 234 |
pinctrl-0 = <&pins_mmc1>; |
| 235 |
|
| 236 |
cd-gpios = <&gpc 20 GPIO_ACTIVE_LOW>; |
| 237 |
}; |
| 238 |
|
| 239 |
&uart { |
| 240 |
/* |
| 241 |
* The pins for RX/TX are used for the right shoulder button and |
| 242 |
* backlight PWM. |
| 243 |
*/ |
| 244 |
status = "disabled"; |
| 245 |
}; |
| 246 |
|
| 247 |
&nemc { |
| 248 |
nandc: nand-controller@1 { |
| 249 |
compatible = "ingenic,jz4725b-nand"; |
| 250 |
reg = <1 0 0x4000000>; |
| 251 |
|
| 252 |
#address-cells = <1>; |
| 253 |
#size-cells = <0>; |
| 254 |
|
| 255 |
ecc-engine = <&bch>; |
| 256 |
|
| 257 |
ingenic,nemc-tAS = <10>; |
| 258 |
ingenic,nemc-tAH = <5>; |
| 259 |
ingenic,nemc-tBP = <10>; |
| 260 |
ingenic,nemc-tAW = <15>; |
| 261 |
ingenic,nemc-tSTRV = <100>; |
| 262 |
|
| 263 |
pinctrl-names = "default"; |
| 264 |
pinctrl-0 = <&pins_nemc>; |
| 265 |
|
| 266 |
rb-gpios = <&gpc 27 GPIO_ACTIVE_HIGH>; |
| 267 |
|
| 268 |
nand@1 { |
| 269 |
reg = <1>; |
| 270 |
|
| 271 |
nand-ecc-step-size = <512>; |
| 272 |
nand-ecc-strength = <8>; |
| 273 |
nand-ecc-mode = "hw"; |
| 274 |
nand-is-boot-medium; |
| 275 |
nand-on-flash-bbt; |
| 276 |
|
| 277 |
partitions { |
| 278 |
compatible = "fixed-partitions"; |
| 279 |
#address-cells = <1>; |
| 280 |
#size-cells = <1>; |
| 281 |
|
| 282 |
partition@0 { |
| 283 |
label = "bootloader"; |
| 284 |
reg = <0x0 0x20000>; |
| 285 |
}; |
| 286 |
|
| 287 |
partition@20000 { |
| 288 |
label = "system"; |
| 289 |
reg = <0x20000 0x0>; |
| 290 |
}; |
| 291 |
}; |
| 292 |
}; |
| 293 |
}; |
| 294 |
}; |
| 295 |
|
| 296 |
&cgu { |
| 297 |
/* Use 32kHz oscillator as the parent of the RTC clock */ |
| 298 |
assigned-clocks = <&cgu JZ4725B_CLK_RTC>; |
| 299 |
assigned-clock-parents = <&cgu JZ4725B_CLK_OSC32K>; |
| 300 |
}; |
| 301 |
|
| 302 |
&tcu { |
| 303 |
/* |
| 304 |
* 750 kHz for the system timer and clocksource, and use RTC as the |
| 305 |
* parent for the watchdog clock. |
| 306 |
*/ |
| 307 |
assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>, <&tcu TCU_CLK_WDT>; |
| 308 |
assigned-clock-parents = <0>, <0>, <&cgu JZ4725B_CLK_RTC>; |
| 309 |
assigned-clock-rates = <750000>, <750000>; |
| 310 |
}; |
| 311 |
|
| 312 |
&lcd { |
| 313 |
memory-region = <&vmem>; |
| 314 |
|
| 315 |
pinctrl-names = "default"; |
| 316 |
pinctrl-0 = <&pins_lcd>; |
| 317 |
}; |
| 318 |
|
| 319 |
&lcd_ports { |
| 320 |
port@0 { |
| 321 |
reg = <0>; |
| 322 |
|
| 323 |
panel_output: endpoint { |
| 324 |
remote-endpoint = <&panel_input>; |
| 325 |
}; |
| 326 |
}; |
| 327 |
}; |