| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include "x1000.dtsi" |
| 5 |
#include <dt-bindings/gpio/gpio.h> |
| 6 |
#include <dt-bindings/clock/ingenic,sysost.h> |
| 7 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 8 |
|
| 9 |
/ { |
| 10 |
compatible = "yna,cu1000-neo", "ingenic,x1000e"; |
| 11 |
model = "YSH & ATIL General Board CU1000-Neo"; |
| 12 |
|
| 13 |
aliases { |
| 14 |
serial2 = &uart2; |
| 15 |
}; |
| 16 |
|
| 17 |
chosen { |
| 18 |
stdout-path = "serial2:115200n8"; |
| 19 |
}; |
| 20 |
|
| 21 |
memory { |
| 22 |
device_type = "memory"; |
| 23 |
reg = <0x0 0x04000000>; |
| 24 |
}; |
| 25 |
|
| 26 |
leds { |
| 27 |
compatible = "gpio-leds"; |
| 28 |
led-0 { |
| 29 |
gpios = <&gpb 21 GPIO_ACTIVE_HIGH>; |
| 30 |
linux,default-trigger = "mmc0"; |
| 31 |
}; |
| 32 |
}; |
| 33 |
|
| 34 |
wlan_pwrseq: msc1-pwrseq { |
| 35 |
compatible = "mmc-pwrseq-simple"; |
| 36 |
|
| 37 |
reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>; |
| 38 |
post-power-on-delay-ms = <200>; |
| 39 |
}; |
| 40 |
}; |
| 41 |
|
| 42 |
&exclk { |
| 43 |
clock-frequency = <24000000>; |
| 44 |
}; |
| 45 |
|
| 46 |
&cgu { |
| 47 |
/* |
| 48 |
* Use the 32.768 kHz oscillator as the parent of the RTC for a higher |
| 49 |
* precision. |
| 50 |
*/ |
| 51 |
assigned-clocks = <&cgu X1000_CLK_RTC>; |
| 52 |
assigned-clock-parents = <&cgu X1000_CLK_RTCLK>; |
| 53 |
}; |
| 54 |
|
| 55 |
&ost { |
| 56 |
/* 1500 kHz for the system timer and clocksource */ |
| 57 |
assigned-clocks = <&ost OST_CLK_EVENT_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>; |
| 58 |
assigned-clock-rates = <1500000>, <1500000>; |
| 59 |
}; |
| 60 |
|
| 61 |
&uart2 { |
| 62 |
status = "okay"; |
| 63 |
|
| 64 |
pinctrl-names = "default"; |
| 65 |
pinctrl-0 = <&pins_uart2>; |
| 66 |
}; |
| 67 |
|
| 68 |
&ssi { |
| 69 |
status = "okay"; |
| 70 |
|
| 71 |
num-cs = <2>; |
| 72 |
cs-gpios = <0>, <&gpc 20 GPIO_ACTIVE_LOW>; |
| 73 |
|
| 74 |
pinctrl-names = "default"; |
| 75 |
pinctrl-0 = <&pins_ssi>; |
| 76 |
|
| 77 |
sc16is752: expander@0 { |
| 78 |
compatible = "nxp,sc16is752"; |
| 79 |
reg = <0>; /* CE0 */ |
| 80 |
|
| 81 |
spi-rx-bus-width = <1>; |
| 82 |
spi-tx-bus-width = <1>; |
| 83 |
spi-max-frequency = <4000000>; |
| 84 |
|
| 85 |
clocks = <&exclk_sc16is752>; |
| 86 |
|
| 87 |
interrupt-parent = <&gpc>; |
| 88 |
interrupts = <6 IRQ_TYPE_EDGE_FALLING>; |
| 89 |
|
| 90 |
gpio-controller; |
| 91 |
#gpio-cells = <2>; |
| 92 |
|
| 93 |
exclk_sc16is752: sc16is752 { |
| 94 |
compatible = "fixed-clock"; |
| 95 |
#clock-cells = <0>; |
| 96 |
clock-frequency = <48000000>; |
| 97 |
}; |
| 98 |
}; |
| 99 |
}; |
| 100 |
|
| 101 |
&i2c0 { |
| 102 |
status = "okay"; |
| 103 |
|
| 104 |
clock-frequency = <400000>; |
| 105 |
|
| 106 |
pinctrl-names = "default"; |
| 107 |
pinctrl-0 = <&pins_i2c0>; |
| 108 |
|
| 109 |
ads7830: adc@48 { |
| 110 |
compatible = "ti,ads7830"; |
| 111 |
reg = <0x48>; |
| 112 |
}; |
| 113 |
}; |
| 114 |
|
| 115 |
&msc0 { |
| 116 |
status = "okay"; |
| 117 |
|
| 118 |
bus-width = <8>; |
| 119 |
max-frequency = <50000000>; |
| 120 |
|
| 121 |
pinctrl-names = "default"; |
| 122 |
pinctrl-0 = <&pins_msc0>; |
| 123 |
|
| 124 |
non-removable; |
| 125 |
}; |
| 126 |
|
| 127 |
&msc1 { |
| 128 |
status = "okay"; |
| 129 |
|
| 130 |
#address-cells = <1>; |
| 131 |
#size-cells = <0>; |
| 132 |
bus-width = <4>; |
| 133 |
max-frequency = <50000000>; |
| 134 |
|
| 135 |
pinctrl-names = "default"; |
| 136 |
pinctrl-0 = <&pins_msc1>; |
| 137 |
|
| 138 |
non-removable; |
| 139 |
|
| 140 |
mmc-pwrseq = <&wlan_pwrseq>; |
| 141 |
|
| 142 |
ap6212a: wifi@1 { |
| 143 |
compatible = "brcm,bcm4329-fmac"; |
| 144 |
reg = <1>; |
| 145 |
|
| 146 |
interrupt-parent = <&gpc>; |
| 147 |
interrupts = <16 IRQ_TYPE_EDGE_FALLING>; |
| 148 |
interrupt-names = "host-wake"; |
| 149 |
|
| 150 |
brcm,drive-strength = <10>; |
| 151 |
}; |
| 152 |
}; |
| 153 |
|
| 154 |
&mac { |
| 155 |
status = "okay"; |
| 156 |
|
| 157 |
phy-mode = "rmii"; |
| 158 |
phy-handle = <&lan8720a>; |
| 159 |
|
| 160 |
pinctrl-names = "default"; |
| 161 |
pinctrl-0 = <&pins_mac>; |
| 162 |
|
| 163 |
snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */ |
| 164 |
snps,reset-active-low; |
| 165 |
snps,reset-delays-us = <0 10000 30000>; |
| 166 |
}; |
| 167 |
|
| 168 |
&mdio { |
| 169 |
status = "okay"; |
| 170 |
|
| 171 |
lan8720a: ethernet-phy@0 { |
| 172 |
compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22"; |
| 173 |
reg = <0>; |
| 174 |
}; |
| 175 |
}; |
| 176 |
|
| 177 |
&otg_phy { |
| 178 |
status = "okay"; |
| 179 |
}; |
| 180 |
|
| 181 |
&otg { |
| 182 |
status = "okay"; |
| 183 |
}; |
| 184 |
|
| 185 |
&pinctrl { |
| 186 |
pins_uart2: uart2 { |
| 187 |
function = "uart2"; |
| 188 |
groups = "uart2-data-d"; |
| 189 |
bias-pull-up; |
| 190 |
}; |
| 191 |
|
| 192 |
pins_ssi: ssi { |
| 193 |
function = "ssi"; |
| 194 |
groups = "ssi-dt-d", "ssi-dr-d", "ssi-clk-d", "ssi-ce0-d"; |
| 195 |
bias-disable; |
| 196 |
}; |
| 197 |
|
| 198 |
pins_i2c0: i2c0 { |
| 199 |
function = "i2c0"; |
| 200 |
groups = "i2c0-data"; |
| 201 |
bias-pull-up; |
| 202 |
}; |
| 203 |
|
| 204 |
pins_msc0: msc0 { |
| 205 |
function = "mmc0"; |
| 206 |
groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit"; |
| 207 |
bias-disable; |
| 208 |
}; |
| 209 |
|
| 210 |
pins_msc1: msc1 { |
| 211 |
function = "mmc1"; |
| 212 |
groups = "mmc1-1bit", "mmc1-4bit"; |
| 213 |
bias-disable; |
| 214 |
}; |
| 215 |
|
| 216 |
pins_mac: mac { |
| 217 |
function = "mac"; |
| 218 |
groups = "mac"; |
| 219 |
bias-disable; |
| 220 |
}; |
| 221 |
}; |