| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include "jz4780.dtsi" |
| 5 |
#include <dt-bindings/clock/ingenic,tcu.h> |
| 6 |
#include <dt-bindings/gpio/gpio.h> |
| 7 |
#include <dt-bindings/input/input.h> |
| 8 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 9 |
#include <dt-bindings/regulator/active-semi,8865-regulator.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
compatible = "img,ci20", "ingenic,jz4780"; |
| 13 |
|
| 14 |
aliases { |
| 15 |
serial0 = &uart0; |
| 16 |
serial1 = &uart1; |
| 17 |
serial3 = &uart3; |
| 18 |
serial4 = &uart4; |
| 19 |
}; |
| 20 |
|
| 21 |
chosen { |
| 22 |
stdout-path = &uart4; |
| 23 |
}; |
| 24 |
|
| 25 |
memory { |
| 26 |
device_type = "memory"; |
| 27 |
reg = <0x0 0x10000000 |
| 28 |
0x30000000 0x30000000>; |
| 29 |
}; |
| 30 |
|
| 31 |
gpio-keys { |
| 32 |
compatible = "gpio-keys"; |
| 33 |
|
| 34 |
switch { |
| 35 |
label = "ci20:sw1"; |
| 36 |
linux,code = <KEY_F13>; |
| 37 |
gpios = <&gpd 17 GPIO_ACTIVE_HIGH>; |
| 38 |
wakeup-source; |
| 39 |
}; |
| 40 |
}; |
| 41 |
|
| 42 |
leds { |
| 43 |
compatible = "gpio-leds"; |
| 44 |
|
| 45 |
led-0 { |
| 46 |
label = "ci20:red:led0"; |
| 47 |
gpios = <&gpc 3 GPIO_ACTIVE_HIGH>; |
| 48 |
linux,default-trigger = "none"; |
| 49 |
}; |
| 50 |
|
| 51 |
led-1 { |
| 52 |
label = "ci20:red:led1"; |
| 53 |
gpios = <&gpc 2 GPIO_ACTIVE_HIGH>; |
| 54 |
linux,default-trigger = "nand-disk"; |
| 55 |
}; |
| 56 |
|
| 57 |
led-2 { |
| 58 |
label = "ci20:red:led2"; |
| 59 |
gpios = <&gpc 1 GPIO_ACTIVE_HIGH>; |
| 60 |
linux,default-trigger = "cpu1"; |
| 61 |
}; |
| 62 |
|
| 63 |
led-3 { |
| 64 |
label = "ci20:red:led3"; |
| 65 |
gpios = <&gpc 0 GPIO_ACTIVE_HIGH>; |
| 66 |
linux,default-trigger = "cpu0"; |
| 67 |
}; |
| 68 |
}; |
| 69 |
|
| 70 |
eth0_power: fixedregulator-0 { |
| 71 |
compatible = "regulator-fixed"; |
| 72 |
|
| 73 |
regulator-name = "eth0_power"; |
| 74 |
regulator-min-microvolt = <3300000>; |
| 75 |
regulator-max-microvolt = <3300000>; |
| 76 |
|
| 77 |
gpio = <&gpb 25 0>; |
| 78 |
enable-active-high; |
| 79 |
}; |
| 80 |
|
| 81 |
hdmi_out: connector { |
| 82 |
compatible = "hdmi-connector"; |
| 83 |
label = "HDMI OUT"; |
| 84 |
type = "a"; |
| 85 |
|
| 86 |
ddc-en-gpios = <&gpa 25 GPIO_ACTIVE_HIGH>; |
| 87 |
|
| 88 |
port { |
| 89 |
hdmi_con: endpoint { |
| 90 |
remote-endpoint = <&dw_hdmi_out>; |
| 91 |
}; |
| 92 |
}; |
| 93 |
}; |
| 94 |
|
| 95 |
ir: ir { |
| 96 |
compatible = "gpio-ir-receiver"; |
| 97 |
gpios = <&gpe 3 GPIO_ACTIVE_LOW>; |
| 98 |
}; |
| 99 |
|
| 100 |
bt_power: fixedregulator-1 { |
| 101 |
compatible = "regulator-fixed"; |
| 102 |
|
| 103 |
regulator-name = "bt_power"; |
| 104 |
regulator-min-microvolt = <3300000>; |
| 105 |
regulator-max-microvolt = <3300000>; |
| 106 |
regulator-settling-time-us = <1400>; |
| 107 |
|
| 108 |
vin-supply = <&vcc_50>; |
| 109 |
|
| 110 |
gpio = <&gpb 19 0>; |
| 111 |
enable-active-high; |
| 112 |
}; |
| 113 |
|
| 114 |
otg_power: fixedregulator-2 { |
| 115 |
compatible = "regulator-fixed"; |
| 116 |
|
| 117 |
regulator-name = "otg_power"; |
| 118 |
regulator-min-microvolt = <5000000>; |
| 119 |
regulator-max-microvolt = <5000000>; |
| 120 |
|
| 121 |
gpio = <&gpf 15 0>; |
| 122 |
enable-active-high; |
| 123 |
}; |
| 124 |
|
| 125 |
wifi_power: fixedregulator-4 { |
| 126 |
compatible = "regulator-fixed"; |
| 127 |
|
| 128 |
regulator-name = "wifi_power"; |
| 129 |
|
| 130 |
/* |
| 131 |
* Technically it's 5V, the WiFi chip has its own internal |
| 132 |
* regulators; but the MMC/SD subsystem won't accept such a |
| 133 |
* value. |
| 134 |
*/ |
| 135 |
regulator-min-microvolt = <3300000>; |
| 136 |
regulator-max-microvolt = <3300000>; |
| 137 |
regulator-settling-time-us = <150000>; |
| 138 |
|
| 139 |
vin-supply = <&bt_power>; |
| 140 |
}; |
| 141 |
|
| 142 |
vcc_33v: fixedregulator-5 { |
| 143 |
compatible = "regulator-fixed"; |
| 144 |
|
| 145 |
regulator-name = "vcc_33v"; |
| 146 |
regulator-min-microvolt = <3300000>; |
| 147 |
regulator-max-microvolt = <3300000>; |
| 148 |
regulator-always-on; |
| 149 |
}; |
| 150 |
|
| 151 |
wifi_pwrseq: pwrseq { |
| 152 |
compatible = "mmc-pwrseq-simple"; |
| 153 |
reset-gpios = <&gpf 7 GPIO_ACTIVE_LOW>; |
| 154 |
|
| 155 |
clocks = <&rtc_dev>; |
| 156 |
clock-names = "ext_clock"; |
| 157 |
}; |
| 158 |
}; |
| 159 |
|
| 160 |
&ext { |
| 161 |
clock-frequency = <48000000>; |
| 162 |
}; |
| 163 |
|
| 164 |
&cgu { |
| 165 |
/* |
| 166 |
* Use the 32.768 kHz oscillator as the parent of the RTC for a higher |
| 167 |
* precision. |
| 168 |
*/ |
| 169 |
assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>, |
| 170 |
<&cgu JZ4780_CLK_SSIPLL>, <&cgu JZ4780_CLK_SSI>, |
| 171 |
<&cgu JZ4780_CLK_HDMI>, <&cgu JZ4780_CLK_MSCMUX>; |
| 172 |
assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>, |
| 173 |
<&cgu JZ4780_CLK_MPLL>, |
| 174 |
<&cgu JZ4780_CLK_SSIPLL>, |
| 175 |
<0>, <&cgu JZ4780_CLK_MPLL>; |
| 176 |
assigned-clock-rates = <48000000>, <0>, <54000000>, <0>, <27000000>; |
| 177 |
}; |
| 178 |
|
| 179 |
&tcu { |
| 180 |
/* |
| 181 |
* 750 kHz for the system timers and clocksource, |
| 182 |
* use channel #0 and #1 for the per cpu system timers, |
| 183 |
* and use channel #2 for the clocksource. |
| 184 |
* |
| 185 |
* 3000 kHz for the OST timer to provide a higher |
| 186 |
* precision clocksource. |
| 187 |
*/ |
| 188 |
assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>, |
| 189 |
<&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_OST>; |
| 190 |
assigned-clock-rates = <750000>, <750000>, <750000>, <3000000>; |
| 191 |
}; |
| 192 |
|
| 193 |
&mmc0 { |
| 194 |
status = "okay"; |
| 195 |
|
| 196 |
bus-width = <4>; |
| 197 |
max-frequency = <50000000>; |
| 198 |
|
| 199 |
pinctrl-names = "default"; |
| 200 |
pinctrl-0 = <&pins_mmc0>; |
| 201 |
|
| 202 |
cd-gpios = <&gpf 20 GPIO_ACTIVE_LOW>; |
| 203 |
vmmc-supply = <&vcc_33v>; |
| 204 |
vqmmc-supply = <&vcc_33v>; |
| 205 |
}; |
| 206 |
|
| 207 |
&mmc1 { |
| 208 |
status = "okay"; |
| 209 |
|
| 210 |
bus-width = <4>; |
| 211 |
max-frequency = <25000000>; |
| 212 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 213 |
vmmc-supply = <&wifi_power>; |
| 214 |
vqmmc-supply = <&wifi_io>; |
| 215 |
non-removable; |
| 216 |
|
| 217 |
pinctrl-names = "default"; |
| 218 |
pinctrl-0 = <&pins_mmc1>; |
| 219 |
|
| 220 |
#address-cells = <1>; |
| 221 |
#size-cells = <0>; |
| 222 |
|
| 223 |
wifi@1 { |
| 224 |
compatible = "brcm,bcm4329-fmac"; |
| 225 |
reg = <1>; |
| 226 |
|
| 227 |
interrupt-parent = <&gpd>; |
| 228 |
interrupts = <9 IRQ_TYPE_EDGE_FALLING>; |
| 229 |
interrupt-names = "host-wake"; |
| 230 |
}; |
| 231 |
}; |
| 232 |
|
| 233 |
&uart0 { |
| 234 |
status = "okay"; |
| 235 |
|
| 236 |
pinctrl-names = "default"; |
| 237 |
pinctrl-0 = <&pins_uart0>; |
| 238 |
}; |
| 239 |
|
| 240 |
&uart1 { |
| 241 |
status = "okay"; |
| 242 |
|
| 243 |
pinctrl-names = "default"; |
| 244 |
pinctrl-0 = <&pins_uart1>; |
| 245 |
}; |
| 246 |
|
| 247 |
&uart2 { |
| 248 |
status = "okay"; |
| 249 |
|
| 250 |
pinctrl-names = "default"; |
| 251 |
pinctrl-0 = <&pins_uart2>; |
| 252 |
uart-has-rtscts; |
| 253 |
|
| 254 |
bluetooth { |
| 255 |
compatible = "brcm,bcm4330-bt"; |
| 256 |
|
| 257 |
vbat-supply = <&bt_power>; |
| 258 |
vddio-supply = <&wifi_io>; |
| 259 |
|
| 260 |
interrupt-parent = <&gpf>; |
| 261 |
interrupts = <6 IRQ_TYPE_EDGE_RISING>; |
| 262 |
interrupt-names = "host-wakeup"; |
| 263 |
|
| 264 |
clocks = <&rtc_dev>; |
| 265 |
clock-names = "lpo"; |
| 266 |
|
| 267 |
reset-gpios = <&gpf 8 GPIO_ACTIVE_LOW>; |
| 268 |
device-wakeup-gpios = <&gpf 5 GPIO_ACTIVE_HIGH>; |
| 269 |
shutdown-gpios = <&gpf 4 GPIO_ACTIVE_HIGH>; |
| 270 |
}; |
| 271 |
}; |
| 272 |
|
| 273 |
&uart3 { |
| 274 |
status = "okay"; |
| 275 |
|
| 276 |
pinctrl-names = "default"; |
| 277 |
pinctrl-0 = <&pins_uart3>; |
| 278 |
}; |
| 279 |
|
| 280 |
&uart4 { |
| 281 |
status = "okay"; |
| 282 |
|
| 283 |
pinctrl-names = "default"; |
| 284 |
pinctrl-0 = <&pins_uart4>; |
| 285 |
}; |
| 286 |
|
| 287 |
&i2c0 { |
| 288 |
status = "okay"; |
| 289 |
|
| 290 |
pinctrl-names = "default"; |
| 291 |
pinctrl-0 = <&pins_i2c0>; |
| 292 |
|
| 293 |
clock-frequency = <400000>; |
| 294 |
|
| 295 |
act8600: act8600@5a { |
| 296 |
compatible = "active-semi,act8600"; |
| 297 |
reg = <0x5a>; |
| 298 |
|
| 299 |
regulators { |
| 300 |
vddcore: DCDC1 { |
| 301 |
regulator-min-microvolt = <1125000>; |
| 302 |
regulator-max-microvolt = <1125000>; |
| 303 |
vp1-supply = <&vcc_33v>; |
| 304 |
regulator-always-on; |
| 305 |
}; |
| 306 |
vddmem: DCDC2 { |
| 307 |
regulator-min-microvolt = <1500000>; |
| 308 |
regulator-max-microvolt = <1500000>; |
| 309 |
vp2-supply = <&vcc_33v>; |
| 310 |
regulator-always-on; |
| 311 |
}; |
| 312 |
vcc_33: DCDC3 { |
| 313 |
regulator-min-microvolt = <3300000>; |
| 314 |
regulator-max-microvolt = <3300000>; |
| 315 |
vp3-supply = <&vcc_33v>; |
| 316 |
regulator-always-on; |
| 317 |
}; |
| 318 |
vcc_50: SUDCDC_REG4 { |
| 319 |
regulator-min-microvolt = <5000000>; |
| 320 |
regulator-max-microvolt = <5000000>; |
| 321 |
regulator-always-on; |
| 322 |
}; |
| 323 |
vcc_25: LDO5 { |
| 324 |
regulator-min-microvolt = <2500000>; |
| 325 |
regulator-max-microvolt = <2500000>; |
| 326 |
inl-supply = <&vcc_33v>; |
| 327 |
regulator-always-on; |
| 328 |
}; |
| 329 |
wifi_io: LDO6 { |
| 330 |
regulator-min-microvolt = <1800000>; |
| 331 |
regulator-max-microvolt = <1800000>; |
| 332 |
regulator-settling-time-us = <150000>; |
| 333 |
inl-supply = <&vcc_33v>; |
| 334 |
}; |
| 335 |
cim_io_28: LDO7 { |
| 336 |
regulator-min-microvolt = <2800000>; |
| 337 |
regulator-max-microvolt = <2800000>; |
| 338 |
inl-supply = <&vcc_33v>; |
| 339 |
}; |
| 340 |
cim_io_15: LDO8 { |
| 341 |
regulator-min-microvolt = <1500000>; |
| 342 |
regulator-max-microvolt = <1500000>; |
| 343 |
inl-supply = <&vcc_33v>; |
| 344 |
}; |
| 345 |
vrtc_18: LDO_REG9 { |
| 346 |
/* Despite the datasheet stating 3.3V |
| 347 |
* for REG9 and the driver expecting that, |
| 348 |
* REG9 outputs 1.8V. |
| 349 |
* Likely the CI20 uses a proprietary |
| 350 |
* factory programmed chip variant. |
| 351 |
* Since this is a simple on/off LDO the |
| 352 |
* exact values do not matter. |
| 353 |
*/ |
| 354 |
regulator-min-microvolt = <3300000>; |
| 355 |
regulator-max-microvolt = <3300000>; |
| 356 |
regulator-always-on; |
| 357 |
}; |
| 358 |
vcc_11: LDO_REG10 { |
| 359 |
regulator-min-microvolt = <1200000>; |
| 360 |
regulator-max-microvolt = <1200000>; |
| 361 |
regulator-always-on; |
| 362 |
}; |
| 363 |
}; |
| 364 |
}; |
| 365 |
}; |
| 366 |
|
| 367 |
&i2c1 { |
| 368 |
status = "okay"; |
| 369 |
|
| 370 |
pinctrl-names = "default"; |
| 371 |
pinctrl-0 = <&pins_i2c1>; |
| 372 |
|
| 373 |
}; |
| 374 |
|
| 375 |
&i2c2 { |
| 376 |
status = "okay"; |
| 377 |
|
| 378 |
pinctrl-names = "default"; |
| 379 |
pinctrl-0 = <&pins_i2c2>; |
| 380 |
|
| 381 |
}; |
| 382 |
|
| 383 |
&i2c3 { |
| 384 |
status = "okay"; |
| 385 |
|
| 386 |
pinctrl-names = "default"; |
| 387 |
pinctrl-0 = <&pins_i2c3>; |
| 388 |
|
| 389 |
}; |
| 390 |
|
| 391 |
&i2c4 { |
| 392 |
status = "okay"; |
| 393 |
|
| 394 |
pinctrl-names = "default"; |
| 395 |
pinctrl-0 = <&pins_i2c4>; |
| 396 |
|
| 397 |
clock-frequency = <400000>; |
| 398 |
|
| 399 |
rtc@51 { |
| 400 |
compatible = "nxp,pcf8563"; |
| 401 |
reg = <0x51>; |
| 402 |
|
| 403 |
interrupt-parent = <&gpf>; |
| 404 |
interrupts = <30 IRQ_TYPE_LEVEL_LOW>; |
| 405 |
}; |
| 406 |
}; |
| 407 |
|
| 408 |
&nemc { |
| 409 |
status = "okay"; |
| 410 |
|
| 411 |
nandc: nand-controller@1 { |
| 412 |
compatible = "ingenic,jz4780-nand"; |
| 413 |
reg = <1 0 0x1000000>; |
| 414 |
|
| 415 |
#address-cells = <1>; |
| 416 |
#size-cells = <0>; |
| 417 |
|
| 418 |
ecc-engine = <&bch>; |
| 419 |
|
| 420 |
ingenic,nemc-tAS = <10>; |
| 421 |
ingenic,nemc-tAH = <5>; |
| 422 |
ingenic,nemc-tBP = <10>; |
| 423 |
ingenic,nemc-tAW = <15>; |
| 424 |
ingenic,nemc-tSTRV = <100>; |
| 425 |
|
| 426 |
/* |
| 427 |
* Only CLE/ALE are needed for the devices that are connected, rather |
| 428 |
* than the full address line set. |
| 429 |
*/ |
| 430 |
pinctrl-names = "default"; |
| 431 |
pinctrl-0 = <&pins_nemc>; |
| 432 |
|
| 433 |
nand@1 { |
| 434 |
reg = <1>; |
| 435 |
|
| 436 |
nand-ecc-step-size = <1024>; |
| 437 |
nand-ecc-strength = <24>; |
| 438 |
nand-ecc-mode = "hw"; |
| 439 |
nand-on-flash-bbt; |
| 440 |
|
| 441 |
pinctrl-names = "default"; |
| 442 |
pinctrl-0 = <&pins_nemc_cs1>; |
| 443 |
|
| 444 |
partitions { |
| 445 |
compatible = "fixed-partitions"; |
| 446 |
#address-cells = <2>; |
| 447 |
#size-cells = <2>; |
| 448 |
|
| 449 |
partition@0 { |
| 450 |
label = "u-boot-spl"; |
| 451 |
reg = <0x0 0x0 0x0 0x800000>; |
| 452 |
}; |
| 453 |
|
| 454 |
partition@800000 { |
| 455 |
label = "u-boot"; |
| 456 |
reg = <0x0 0x800000 0x0 0x200000>; |
| 457 |
}; |
| 458 |
|
| 459 |
partition@a00000 { |
| 460 |
label = "u-boot-env"; |
| 461 |
reg = <0x0 0xa00000 0x0 0x200000>; |
| 462 |
}; |
| 463 |
|
| 464 |
partition@c00000 { |
| 465 |
label = "boot"; |
| 466 |
reg = <0x0 0xc00000 0x0 0x4000000>; |
| 467 |
}; |
| 468 |
|
| 469 |
partition@4c00000 { |
| 470 |
label = "system"; |
| 471 |
reg = <0x0 0x4c00000 0x1 0xfb400000>; |
| 472 |
}; |
| 473 |
}; |
| 474 |
}; |
| 475 |
}; |
| 476 |
|
| 477 |
dm9000@6 { |
| 478 |
compatible = "davicom,dm9000"; |
| 479 |
davicom,no-eeprom; |
| 480 |
|
| 481 |
pinctrl-names = "default"; |
| 482 |
pinctrl-0 = <&pins_nemc_cs6>; |
| 483 |
|
| 484 |
reg = <6 0 1>, /* addr */ |
| 485 |
<6 2 1>; /* data */ |
| 486 |
|
| 487 |
ingenic,nemc-tAS = <15>; |
| 488 |
ingenic,nemc-tAH = <10>; |
| 489 |
ingenic,nemc-tBP = <20>; |
| 490 |
ingenic,nemc-tAW = <50>; |
| 491 |
ingenic,nemc-tSTRV = <100>; |
| 492 |
|
| 493 |
reset-gpios = <&gpf 12 GPIO_ACTIVE_LOW>; |
| 494 |
vcc-supply = <ð0_power>; |
| 495 |
|
| 496 |
interrupt-parent = <&gpe>; |
| 497 |
interrupts = <19 IRQ_TYPE_EDGE_RISING>; |
| 498 |
|
| 499 |
nvmem-cells = <ð0_addr>; |
| 500 |
nvmem-cell-names = "mac-address"; |
| 501 |
}; |
| 502 |
}; |
| 503 |
|
| 504 |
&bch { |
| 505 |
status = "okay"; |
| 506 |
}; |
| 507 |
|
| 508 |
&otg_phy { |
| 509 |
status = "okay"; |
| 510 |
|
| 511 |
vcc-supply = <&otg_power>; |
| 512 |
}; |
| 513 |
|
| 514 |
&otg { |
| 515 |
status = "okay"; |
| 516 |
}; |
| 517 |
|
| 518 |
&pinctrl { |
| 519 |
pins_uart0: uart0 { |
| 520 |
function = "uart0"; |
| 521 |
groups = "uart0-data"; |
| 522 |
bias-disable; |
| 523 |
}; |
| 524 |
|
| 525 |
pins_uart1: uart1 { |
| 526 |
function = "uart1"; |
| 527 |
groups = "uart1-data"; |
| 528 |
bias-disable; |
| 529 |
}; |
| 530 |
|
| 531 |
pins_uart2: uart2 { |
| 532 |
function = "uart2"; |
| 533 |
groups = "uart2-data", "uart2-hwflow"; |
| 534 |
bias-disable; |
| 535 |
}; |
| 536 |
|
| 537 |
pins_uart3: uart3 { |
| 538 |
function = "uart3"; |
| 539 |
groups = "uart3-data", "uart3-hwflow"; |
| 540 |
bias-disable; |
| 541 |
}; |
| 542 |
|
| 543 |
pins_uart4: uart4 { |
| 544 |
function = "uart4"; |
| 545 |
groups = "uart4-data"; |
| 546 |
bias-disable; |
| 547 |
}; |
| 548 |
|
| 549 |
pins_i2c0: i2c0 { |
| 550 |
function = "i2c0"; |
| 551 |
groups = "i2c0-data"; |
| 552 |
bias-disable; |
| 553 |
}; |
| 554 |
|
| 555 |
pins_i2c1: i2c1 { |
| 556 |
function = "i2c1"; |
| 557 |
groups = "i2c1-data"; |
| 558 |
bias-disable; |
| 559 |
}; |
| 560 |
|
| 561 |
pins_i2c2: i2c2 { |
| 562 |
function = "i2c2"; |
| 563 |
groups = "i2c2-data"; |
| 564 |
bias-disable; |
| 565 |
}; |
| 566 |
|
| 567 |
pins_i2c3: i2c3 { |
| 568 |
function = "i2c3"; |
| 569 |
groups = "i2c3-data"; |
| 570 |
bias-disable; |
| 571 |
}; |
| 572 |
|
| 573 |
pins_i2c4: i2c4 { |
| 574 |
function = "i2c4"; |
| 575 |
groups = "i2c4-data-e"; |
| 576 |
bias-disable; |
| 577 |
}; |
| 578 |
|
| 579 |
pins_hdmi_ddc: hdmi_ddc { |
| 580 |
function = "hdmi-ddc"; |
| 581 |
groups = "hdmi-ddc"; |
| 582 |
bias-disable; |
| 583 |
}; |
| 584 |
|
| 585 |
pins_nemc: nemc { |
| 586 |
function = "nemc"; |
| 587 |
groups = "nemc-data", "nemc-cle-ale", "nemc-rd-we", "nemc-frd-fwe"; |
| 588 |
bias-disable; |
| 589 |
}; |
| 590 |
|
| 591 |
pins_nemc_cs1: nemc-cs1 { |
| 592 |
function = "nemc-cs1"; |
| 593 |
groups = "nemc-cs1"; |
| 594 |
bias-disable; |
| 595 |
}; |
| 596 |
|
| 597 |
pins_nemc_cs6: nemc-cs6 { |
| 598 |
function = "nemc-cs6"; |
| 599 |
groups = "nemc-cs6"; |
| 600 |
bias-disable; |
| 601 |
}; |
| 602 |
|
| 603 |
pins_mmc0: mmc0 { |
| 604 |
function = "mmc0"; |
| 605 |
groups = "mmc0-1bit-e", "mmc0-4bit-e"; |
| 606 |
bias-disable; |
| 607 |
}; |
| 608 |
|
| 609 |
pins_mmc1: mmc1 { |
| 610 |
function = "mmc1"; |
| 611 |
groups = "mmc1-1bit-d", "mmc1-4bit-d"; |
| 612 |
bias-disable; |
| 613 |
}; |
| 614 |
}; |
| 615 |
|
| 616 |
&hdmi { |
| 617 |
status = "okay"; |
| 618 |
|
| 619 |
pinctrl-names = "default"; |
| 620 |
pinctrl-0 = <&pins_hdmi_ddc>; |
| 621 |
|
| 622 |
ports { |
| 623 |
#address-cells = <1>; |
| 624 |
#size-cells = <0>; |
| 625 |
|
| 626 |
port@0 { |
| 627 |
reg = <0>; |
| 628 |
dw_hdmi_in: endpoint { |
| 629 |
remote-endpoint = <&lcd_out>; |
| 630 |
}; |
| 631 |
}; |
| 632 |
|
| 633 |
port@1 { |
| 634 |
reg = <1>; |
| 635 |
dw_hdmi_out: endpoint { |
| 636 |
remote-endpoint = <&hdmi_con>; |
| 637 |
}; |
| 638 |
}; |
| 639 |
}; |
| 640 |
}; |
| 641 |
|
| 642 |
&lcdc0 { |
| 643 |
status = "okay"; |
| 644 |
|
| 645 |
port { |
| 646 |
lcd_out: endpoint { |
| 647 |
remote-endpoint = <&dw_hdmi_in>; |
| 648 |
}; |
| 649 |
}; |
| 650 |
}; |