| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/dts-v1/; |
| 3 |
|
| 4 |
#include "jz4770.dtsi" |
| 5 |
#include <dt-bindings/clock/ingenic,tcu.h> |
| 6 |
|
| 7 |
#include <dt-bindings/gpio/gpio.h> |
| 8 |
#include <dt-bindings/iio/adc/ingenic,adc.h> |
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
compatible = "gcw,zero", "ingenic,jz4770"; |
| 13 |
model = "GCW Zero"; |
| 14 |
|
| 15 |
aliases { |
| 16 |
serial0 = &uart0; |
| 17 |
serial1 = &uart1; |
| 18 |
serial2 = &uart2; |
| 19 |
serial3 = &uart3; |
| 20 |
}; |
| 21 |
|
| 22 |
memory: memory { |
| 23 |
device_type = "memory"; |
| 24 |
reg = <0x0 0x10000000>, |
| 25 |
<0x30000000 0x10000000>; |
| 26 |
}; |
| 27 |
|
| 28 |
chosen { |
| 29 |
stdout-path = "serial2:57600n8"; |
| 30 |
}; |
| 31 |
|
| 32 |
vcc: regulator@0 { |
| 33 |
compatible = "regulator-fixed"; |
| 34 |
regulator-name = "vcc"; |
| 35 |
|
| 36 |
regulator-min-microvolt = <3300000>; |
| 37 |
regulator-max-microvolt = <3300000>; |
| 38 |
regulator-always-on; |
| 39 |
}; |
| 40 |
|
| 41 |
mmc1_power: regulator@1 { |
| 42 |
compatible = "regulator-fixed"; |
| 43 |
regulator-name = "mmc1_vcc"; |
| 44 |
gpio = <&gpe 9 0>; |
| 45 |
|
| 46 |
regulator-min-microvolt = <3300000>; |
| 47 |
regulator-max-microvolt = <3300000>; |
| 48 |
vin-supply = <&vcc>; |
| 49 |
}; |
| 50 |
|
| 51 |
headphones_amp: analog-amplifier@0 { |
| 52 |
compatible = "simple-audio-amplifier"; |
| 53 |
enable-gpios = <&gpf 3 GPIO_ACTIVE_LOW>; |
| 54 |
enable-delay-ms = <50>; |
| 55 |
|
| 56 |
VCC-supply = <&ldo5>; |
| 57 |
sound-name-prefix = "Headphones Amp"; |
| 58 |
}; |
| 59 |
|
| 60 |
speaker_amp: analog-amplifier@1 { |
| 61 |
compatible = "simple-audio-amplifier"; |
| 62 |
enable-gpios = <&gpf 20 GPIO_ACTIVE_HIGH>; |
| 63 |
|
| 64 |
VCC-supply = <&ldo5>; |
| 65 |
sound-name-prefix = "Speaker Amp"; |
| 66 |
}; |
| 67 |
|
| 68 |
sound { |
| 69 |
compatible = "simple-audio-card"; |
| 70 |
|
| 71 |
simple-audio-card,name = "gcw0-audio"; |
| 72 |
simple-audio-card,format = "i2s"; |
| 73 |
|
| 74 |
simple-audio-card,widgets = |
| 75 |
"Speaker", "Speaker", |
| 76 |
"Headphone", "Headphones", |
| 77 |
"Microphone", "Built-in Mic"; |
| 78 |
simple-audio-card,routing = |
| 79 |
"Headphones Amp INL", "LHPOUT", |
| 80 |
"Headphones Amp INR", "RHPOUT", |
| 81 |
"Headphones", "Headphones Amp OUTL", |
| 82 |
"Headphones", "Headphones Amp OUTR", |
| 83 |
"Speaker Amp INL", "LOUT", |
| 84 |
"Speaker Amp INR", "ROUT", |
| 85 |
"Speaker", "Speaker Amp OUTL", |
| 86 |
"Speaker", "Speaker Amp OUTR", |
| 87 |
"LLINEIN", "Cap-less", |
| 88 |
"RLINEIN", "Cap-less", |
| 89 |
"Built-in Mic", "MICBIAS", |
| 90 |
"MIC1P", "Built-in Mic", |
| 91 |
"MIC1N", "Built-in Mic"; |
| 92 |
simple-audio-card,pin-switches = "Speaker", "Headphones"; |
| 93 |
|
| 94 |
simple-audio-card,hp-det-gpios = <&gpf 21 GPIO_ACTIVE_LOW>; |
| 95 |
simple-audio-card,aux-devs = <&speaker_amp>, <&headphones_amp>; |
| 96 |
|
| 97 |
simple-audio-card,bitclock-master = <&dai_codec>; |
| 98 |
simple-audio-card,frame-master = <&dai_codec>; |
| 99 |
|
| 100 |
dai_cpu: simple-audio-card,cpu { |
| 101 |
sound-dai = <&aic>; |
| 102 |
}; |
| 103 |
|
| 104 |
dai_codec: simple-audio-card,codec { |
| 105 |
sound-dai = <&codec>; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
rumble { |
| 110 |
compatible = "pwm-vibrator"; |
| 111 |
pwms = <&pwm 4 2000000 0>; |
| 112 |
pwm-names = "enable"; |
| 113 |
|
| 114 |
pinctrl-names = "default"; |
| 115 |
pinctrl-0 = <&pins_pwm4>; |
| 116 |
}; |
| 117 |
|
| 118 |
backlight: backlight { |
| 119 |
compatible = "pwm-backlight"; |
| 120 |
pwms = <&pwm 1 40000 0>; |
| 121 |
power-supply = <&vcc>; |
| 122 |
|
| 123 |
brightness-levels = <0 16 32 48 64 80 96 112 128 |
| 124 |
144 160 176 192 208 224 240 255>; |
| 125 |
default-brightness-level = <12>; |
| 126 |
|
| 127 |
pinctrl-names = "default"; |
| 128 |
pinctrl-0 = <&pins_pwm1>; |
| 129 |
}; |
| 130 |
|
| 131 |
gpio-keys { |
| 132 |
compatible = "gpio-keys"; |
| 133 |
autorepeat; |
| 134 |
|
| 135 |
button-0 { |
| 136 |
label = "D-pad up"; |
| 137 |
linux,code = <KEY_UP>; |
| 138 |
linux,can-disable; |
| 139 |
gpios = <&gpe 21 GPIO_ACTIVE_LOW>; |
| 140 |
}; |
| 141 |
|
| 142 |
button-1 { |
| 143 |
label = "D-pad down"; |
| 144 |
linux,code = <KEY_DOWN>; |
| 145 |
linux,can-disable; |
| 146 |
gpios = <&gpe 25 GPIO_ACTIVE_LOW>; |
| 147 |
}; |
| 148 |
|
| 149 |
button-2 { |
| 150 |
label = "D-pad left"; |
| 151 |
linux,code = <KEY_LEFT>; |
| 152 |
linux,can-disable; |
| 153 |
gpios = <&gpe 23 GPIO_ACTIVE_LOW>; |
| 154 |
}; |
| 155 |
|
| 156 |
button-3 { |
| 157 |
label = "D-pad right"; |
| 158 |
linux,code = <KEY_RIGHT>; |
| 159 |
linux,can-disable; |
| 160 |
gpios = <&gpe 24 GPIO_ACTIVE_LOW>; |
| 161 |
}; |
| 162 |
|
| 163 |
button-4 { |
| 164 |
label = "Button A"; |
| 165 |
linux,code = <KEY_LEFTCTRL>; |
| 166 |
linux,can-disable; |
| 167 |
gpios = <&gpe 29 GPIO_ACTIVE_LOW>; |
| 168 |
}; |
| 169 |
|
| 170 |
button-5 { |
| 171 |
label = "Button B"; |
| 172 |
linux,code = <KEY_LEFTALT>; |
| 173 |
linux,can-disable; |
| 174 |
gpios = <&gpe 20 GPIO_ACTIVE_LOW>; |
| 175 |
}; |
| 176 |
|
| 177 |
button-6 { |
| 178 |
label = "Button Y"; |
| 179 |
linux,code = <KEY_SPACE>; |
| 180 |
linux,can-disable; |
| 181 |
gpios = <&gpe 27 GPIO_ACTIVE_LOW>; |
| 182 |
}; |
| 183 |
|
| 184 |
button-7 { |
| 185 |
label = "Button X"; |
| 186 |
linux,code = <KEY_LEFTSHIFT>; |
| 187 |
linux,can-disable; |
| 188 |
gpios = <&gpe 28 GPIO_ACTIVE_LOW>; |
| 189 |
}; |
| 190 |
|
| 191 |
button-8 { |
| 192 |
label = "Left shoulder button"; |
| 193 |
linux,code = <KEY_TAB>; |
| 194 |
linux,can-disable; |
| 195 |
gpios = <&gpb 20 GPIO_ACTIVE_LOW>; |
| 196 |
}; |
| 197 |
|
| 198 |
button-9 { |
| 199 |
label = "Right shoulder button"; |
| 200 |
linux,code = <KEY_BACKSPACE>; |
| 201 |
linux,can-disable; |
| 202 |
gpios = <&gpe 26 GPIO_ACTIVE_LOW>; |
| 203 |
}; |
| 204 |
|
| 205 |
button-10 { |
| 206 |
label = "Start button"; |
| 207 |
linux,code = <KEY_ENTER>; |
| 208 |
linux,can-disable; |
| 209 |
gpios = <&gpb 21 GPIO_ACTIVE_LOW>; |
| 210 |
}; |
| 211 |
|
| 212 |
button-11 { |
| 213 |
label = "Select button"; |
| 214 |
linux,code = <KEY_ESC>; |
| 215 |
linux,can-disable; |
| 216 |
/* |
| 217 |
* This is the only button that is active high, |
| 218 |
* since it doubles as BOOT_SEL1. |
| 219 |
*/ |
| 220 |
gpios = <&gpd 18 GPIO_ACTIVE_HIGH>; |
| 221 |
}; |
| 222 |
|
| 223 |
button-12 { |
| 224 |
label = "Power slider"; |
| 225 |
linux,code = <KEY_POWER>; |
| 226 |
linux,can-disable; |
| 227 |
gpios = <&gpa 30 GPIO_ACTIVE_LOW>; |
| 228 |
wakeup-source; |
| 229 |
}; |
| 230 |
|
| 231 |
button-13 { |
| 232 |
label = "Power hold"; |
| 233 |
linux,code = <KEY_PAUSE>; |
| 234 |
linux,can-disable; |
| 235 |
gpios = <&gpf 11 GPIO_ACTIVE_LOW>; |
| 236 |
}; |
| 237 |
}; |
| 238 |
|
| 239 |
i2c3: i2c-controller@3 { |
| 240 |
compatible = "i2c-gpio"; |
| 241 |
#address-cells = <1>; |
| 242 |
#size-cells = <0>; |
| 243 |
|
| 244 |
sda-gpios = <&gpd 5 GPIO_ACTIVE_HIGH>; |
| 245 |
scl-gpios = <&gpd 4 GPIO_ACTIVE_HIGH>; |
| 246 |
i2c-gpio,delay-us = <2>; /* 250 kHz */ |
| 247 |
|
| 248 |
act8600: pmic@5a { |
| 249 |
compatible = "active-semi,act8600"; |
| 250 |
reg = <0x5a>; |
| 251 |
|
| 252 |
regulators { |
| 253 |
/* USB OTG */ |
| 254 |
otg_vbus: SUDCDC_REG4 { |
| 255 |
/* |
| 256 |
* 5.3V instead of 5.0V to compensate |
| 257 |
* for the voltage drop of a diode |
| 258 |
* between the regulator and the |
| 259 |
* connector. |
| 260 |
*/ |
| 261 |
regulator-min-microvolt = <5300000>; |
| 262 |
regulator-max-microvolt = <5300000>; |
| 263 |
inl-supply = <&vcc>; |
| 264 |
}; |
| 265 |
|
| 266 |
/* |
| 267 |
* When this is off, there is no sound, but also |
| 268 |
* no USB networking. |
| 269 |
*/ |
| 270 |
ldo5: LDO5 { |
| 271 |
regulator-min-microvolt = <2500000>; |
| 272 |
regulator-max-microvolt = <2500000>; |
| 273 |
inl-supply = <&vcc>; |
| 274 |
}; |
| 275 |
|
| 276 |
/* LCD panel and FM radio */ |
| 277 |
ldo6: LDO6 { |
| 278 |
regulator-min-microvolt = <3300000>; |
| 279 |
regulator-max-microvolt = <3300000>; |
| 280 |
inl-supply = <&vcc>; |
| 281 |
}; |
| 282 |
|
| 283 |
/* ??? */ |
| 284 |
LDO7 { |
| 285 |
regulator-min-microvolt = <3300000>; |
| 286 |
regulator-max-microvolt = <3300000>; |
| 287 |
/*regulator-always-on;*/ |
| 288 |
inl-supply = <&vcc>; |
| 289 |
}; |
| 290 |
|
| 291 |
/* |
| 292 |
* The colors on the LCD are wrong when this is |
| 293 |
* off. Which is strange, since the LCD panel |
| 294 |
* data sheet only mentions a 3.3V input. |
| 295 |
*/ |
| 296 |
LDO8 { |
| 297 |
regulator-min-microvolt = <1800000>; |
| 298 |
regulator-max-microvolt = <1800000>; |
| 299 |
regulator-always-on; |
| 300 |
inl-supply = <&vcc>; |
| 301 |
}; |
| 302 |
|
| 303 |
/* RTC fixed 3.3V */ |
| 304 |
LDO_REG9 { |
| 305 |
regulator-min-microvolt = <3300000>; |
| 306 |
regulator-max-microvolt = <3300000>; |
| 307 |
regulator-always-on; |
| 308 |
inl-supply = <&vcc>; |
| 309 |
}; |
| 310 |
|
| 311 |
/* Unused fixed 1.2V */ |
| 312 |
LDO_REG10 { |
| 313 |
inl-supply = <&vcc>; |
| 314 |
}; |
| 315 |
}; |
| 316 |
}; |
| 317 |
}; |
| 318 |
|
| 319 |
leds { |
| 320 |
compatible = "gpio-leds"; |
| 321 |
|
| 322 |
led { |
| 323 |
gpios = <&gpb 30 GPIO_ACTIVE_LOW>; |
| 324 |
default-state = "on"; |
| 325 |
}; |
| 326 |
}; |
| 327 |
|
| 328 |
spi { |
| 329 |
compatible = "spi-gpio"; |
| 330 |
#address-cells = <1>; |
| 331 |
#size-cells = <0>; |
| 332 |
|
| 333 |
sck-gpios = <&gpe 15 GPIO_ACTIVE_HIGH>; |
| 334 |
mosi-gpios = <&gpe 17 GPIO_ACTIVE_HIGH>; |
| 335 |
cs-gpios = <&gpe 16 GPIO_ACTIVE_HIGH>; |
| 336 |
num-chipselects = <1>; |
| 337 |
|
| 338 |
nt39016@0 { |
| 339 |
compatible = "kingdisplay,kd035g6-54nt"; |
| 340 |
reg = <0>; |
| 341 |
|
| 342 |
spi-max-frequency = <3125000>; |
| 343 |
spi-3wire; |
| 344 |
|
| 345 |
reset-gpios = <&gpe 2 GPIO_ACTIVE_LOW>; |
| 346 |
|
| 347 |
backlight = <&backlight>; |
| 348 |
power-supply = <&ldo6>; |
| 349 |
|
| 350 |
port { |
| 351 |
panel_input: endpoint { |
| 352 |
remote-endpoint = <&panel_output>; |
| 353 |
}; |
| 354 |
}; |
| 355 |
}; |
| 356 |
}; |
| 357 |
|
| 358 |
connector { |
| 359 |
compatible = "gpio-usb-b-connector", "usb-b-connector"; |
| 360 |
label = "mini-USB"; |
| 361 |
type = "mini"; |
| 362 |
|
| 363 |
/* |
| 364 |
* USB OTG is not yet working reliably, the ID detection |
| 365 |
* mechanism tends to fry easily for unknown reasons. |
| 366 |
* Until this is fixed, disable OTG by not providing the |
| 367 |
* ID GPIO to the driver. |
| 368 |
*/ |
| 369 |
//id-gpios = <&gpf 18 GPIO_ACTIVE_LOW>; |
| 370 |
|
| 371 |
vbus-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>; |
| 372 |
vbus-supply = <&otg_vbus>; |
| 373 |
|
| 374 |
pinctrl-names = "default"; |
| 375 |
pinctrl-0 = <&pins_otg>; |
| 376 |
|
| 377 |
port { |
| 378 |
usb_ep: endpoint { |
| 379 |
remote-endpoint = <&usb_otg_ep>; |
| 380 |
}; |
| 381 |
}; |
| 382 |
}; |
| 383 |
}; |
| 384 |
|
| 385 |
&ext { |
| 386 |
clock-frequency = <12000000>; |
| 387 |
}; |
| 388 |
|
| 389 |
&pinctrl { |
| 390 |
pins_lcd: lcd { |
| 391 |
function = "lcd"; |
| 392 |
groups = "lcd-24bit"; |
| 393 |
}; |
| 394 |
|
| 395 |
pins_uart2: uart2 { |
| 396 |
function = "uart2"; |
| 397 |
groups = "uart2-data"; |
| 398 |
}; |
| 399 |
|
| 400 |
pins_mmc0: mmc0 { |
| 401 |
function = "mmc0"; |
| 402 |
groups = "mmc0-1bit-a", "mmc0-4bit-a"; |
| 403 |
}; |
| 404 |
|
| 405 |
pins_mmc1: mmc1 { |
| 406 |
function = "mmc1"; |
| 407 |
groups = "mmc1-1bit-d", "mmc1-4bit-d"; |
| 408 |
}; |
| 409 |
|
| 410 |
pins_otg: otg { |
| 411 |
otg-vbus-pin { |
| 412 |
function = "otg"; |
| 413 |
groups = "otg-vbus"; |
| 414 |
}; |
| 415 |
|
| 416 |
vbus-pin { |
| 417 |
pins = "PB5"; |
| 418 |
bias-disable; |
| 419 |
}; |
| 420 |
}; |
| 421 |
|
| 422 |
pins_pwm1: pwm1 { |
| 423 |
function = "pwm1"; |
| 424 |
groups = "pwm1"; |
| 425 |
}; |
| 426 |
|
| 427 |
pins_pwm4: pwm4 { |
| 428 |
function = "pwm4"; |
| 429 |
groups = "pwm4"; |
| 430 |
}; |
| 431 |
}; |
| 432 |
|
| 433 |
&uart2 { |
| 434 |
pinctrl-names = "default"; |
| 435 |
pinctrl-0 = <&pins_uart2>; |
| 436 |
|
| 437 |
status = "okay"; |
| 438 |
}; |
| 439 |
|
| 440 |
&cgu { |
| 441 |
/* |
| 442 |
* Put high-speed peripherals under PLL1, such that we can change the |
| 443 |
* PLL0 frequency on demand without having to suspend peripherals. |
| 444 |
* We use a rate of 432 MHz, which is the least common multiple of |
| 445 |
* 27 MHz (required by TV encoder) and 48 MHz (required by USB host). |
| 446 |
* Put the GPU under PLL0 since we want a higher frequency. |
| 447 |
* Use the 32 kHz oscillator as the parent of the RTC for a higher |
| 448 |
* precision. |
| 449 |
*/ |
| 450 |
assigned-clocks = |
| 451 |
<&cgu JZ4770_CLK_PLL1>, |
| 452 |
<&cgu JZ4770_CLK_GPU>, |
| 453 |
<&cgu JZ4770_CLK_RTC>, |
| 454 |
<&cgu JZ4770_CLK_UHC>, |
| 455 |
<&cgu JZ4770_CLK_LPCLK_MUX>, |
| 456 |
<&cgu JZ4770_CLK_MMC0_MUX>, |
| 457 |
<&cgu JZ4770_CLK_MMC1_MUX>; |
| 458 |
assigned-clock-parents = |
| 459 |
<0>, |
| 460 |
<&cgu JZ4770_CLK_PLL0>, |
| 461 |
<&cgu JZ4770_CLK_OSC32K>, |
| 462 |
<&cgu JZ4770_CLK_PLL1>, |
| 463 |
<&cgu JZ4770_CLK_PLL1>, |
| 464 |
<&cgu JZ4770_CLK_PLL1>, |
| 465 |
<&cgu JZ4770_CLK_PLL1>; |
| 466 |
assigned-clock-rates = |
| 467 |
<432000000>, |
| 468 |
<600000000>; |
| 469 |
}; |
| 470 |
|
| 471 |
&uhc { |
| 472 |
/* The WiFi module is connected to the UHC. */ |
| 473 |
status = "okay"; |
| 474 |
}; |
| 475 |
|
| 476 |
&tcu { |
| 477 |
/* |
| 478 |
* 750 kHz for the system timer and clocksource, 12 MHz for the OST, |
| 479 |
* and use RTC as the parent for the watchdog clock |
| 480 |
*/ |
| 481 |
assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>, |
| 482 |
<&tcu TCU_CLK_OST>, <&tcu TCU_CLK_WDT>; |
| 483 |
assigned-clock-parents = <0>, <0>, <0>, <&cgu JZ4770_CLK_RTC>; |
| 484 |
assigned-clock-rates = <750000>, <750000>, <12000000>; |
| 485 |
|
| 486 |
/* PWM1 is in use, so use channel #2 for the clocksource */ |
| 487 |
ingenic,pwm-channels-mask = <0xfa>; |
| 488 |
}; |
| 489 |
|
| 490 |
&usb_otg { |
| 491 |
port { |
| 492 |
usb_otg_ep: endpoint { |
| 493 |
remote-endpoint = <&usb_ep>; |
| 494 |
}; |
| 495 |
}; |
| 496 |
}; |
| 497 |
|
| 498 |
&otg_phy { |
| 499 |
vcc-supply = <&ldo5>; |
| 500 |
}; |
| 501 |
|
| 502 |
&rtc { |
| 503 |
clocks = <&cgu JZ4770_CLK_RTC>; |
| 504 |
clock-names = "rtc"; |
| 505 |
|
| 506 |
system-power-controller; |
| 507 |
}; |
| 508 |
|
| 509 |
&mmc0 { |
| 510 |
status = "okay"; |
| 511 |
|
| 512 |
bus-width = <4>; |
| 513 |
max-frequency = <48000000>; |
| 514 |
vmmc-supply = <&vcc>; |
| 515 |
non-removable; |
| 516 |
|
| 517 |
pinctrl-names = "default"; |
| 518 |
pinctrl-0 = <&pins_mmc0>; |
| 519 |
}; |
| 520 |
|
| 521 |
&mmc1 { |
| 522 |
status = "okay"; |
| 523 |
|
| 524 |
bus-width = <4>; |
| 525 |
max-frequency = <48000000>; |
| 526 |
cd-gpios = <&gpb 2 GPIO_ACTIVE_LOW>; |
| 527 |
vmmc-supply = <&mmc1_power>; |
| 528 |
|
| 529 |
pinctrl-names = "default"; |
| 530 |
pinctrl-0 = <&pins_mmc1>; |
| 531 |
}; |
| 532 |
|
| 533 |
&lcd { |
| 534 |
pinctrl-names = "default"; |
| 535 |
pinctrl-0 = <&pins_lcd>; |
| 536 |
|
| 537 |
port { |
| 538 |
panel_output: endpoint { |
| 539 |
remote-endpoint = <&panel_input>; |
| 540 |
}; |
| 541 |
}; |
| 542 |
}; |