| 1 |
// SPDX-License-Identifier: GPL-2.0+ |
| 2 |
/* |
| 3 |
* Copyright (C) 2015 Altera Corporation <www.altera.com> |
| 4 |
*/ |
| 5 |
#include "socfpga_arria10.dtsi" |
| 6 |
|
| 7 |
/ { |
| 8 |
model = "Altera SOCFPGA Arria 10"; |
| 9 |
compatible = "altr,socfpga-arria10-socdk", "altr,socfpga-arria10", "altr,socfpga"; |
| 10 |
|
| 11 |
aliases { |
| 12 |
ethernet0 = &gmac0; |
| 13 |
serial0 = &uart1; |
| 14 |
}; |
| 15 |
|
| 16 |
chosen { |
| 17 |
bootargs = "earlyprintk"; |
| 18 |
stdout-path = "serial0:115200n8"; |
| 19 |
}; |
| 20 |
|
| 21 |
memory@0 { |
| 22 |
name = "memory"; |
| 23 |
device_type = "memory"; |
| 24 |
reg = <0x0 0x40000000>; /* 1GB */ |
| 25 |
}; |
| 26 |
|
| 27 |
a10leds { |
| 28 |
compatible = "gpio-leds"; |
| 29 |
|
| 30 |
a10sr_led0 { |
| 31 |
label = "a10sr-led0"; |
| 32 |
gpios = <&a10sr_gpio 0 1>; |
| 33 |
}; |
| 34 |
|
| 35 |
a10sr_led1 { |
| 36 |
label = "a10sr-led1"; |
| 37 |
gpios = <&a10sr_gpio 1 1>; |
| 38 |
}; |
| 39 |
|
| 40 |
a10sr_led2 { |
| 41 |
label = "a10sr-led2"; |
| 42 |
gpios = <&a10sr_gpio 2 1>; |
| 43 |
}; |
| 44 |
|
| 45 |
a10sr_led3 { |
| 46 |
label = "a10sr-led3"; |
| 47 |
gpios = <&a10sr_gpio 3 1>; |
| 48 |
}; |
| 49 |
}; |
| 50 |
|
| 51 |
ref_033v: 033-v-ref { |
| 52 |
compatible = "regulator-fixed"; |
| 53 |
regulator-name = "0.33V"; |
| 54 |
regulator-min-microvolt = <330000>; |
| 55 |
regulator-max-microvolt = <330000>; |
| 56 |
}; |
| 57 |
|
| 58 |
soc { |
| 59 |
clkmgr@ffd04000 { |
| 60 |
clocks { |
| 61 |
osc1 { |
| 62 |
clock-frequency = <25000000>; |
| 63 |
}; |
| 64 |
}; |
| 65 |
}; |
| 66 |
}; |
| 67 |
}; |
| 68 |
|
| 69 |
&gmac0 { |
| 70 |
phy-mode = "rgmii"; |
| 71 |
phy-addr = <0xffffffff>; /* probe for phy addr */ |
| 72 |
|
| 73 |
/* |
| 74 |
* These skews assume the user's FPGA design is adding 600ps of delay |
| 75 |
* for TX_CLK on Arria 10. |
| 76 |
* |
| 77 |
* All skews are offset since hardware skew values for the ksz9031 |
| 78 |
* range from a negative skew to a positive skew. |
| 79 |
* See the micrel-ksz90x1.txt Documentation file for details. |
| 80 |
*/ |
| 81 |
txd0-skew-ps = <0>; /* -420ps */ |
| 82 |
txd1-skew-ps = <0>; /* -420ps */ |
| 83 |
txd2-skew-ps = <0>; /* -420ps */ |
| 84 |
txd3-skew-ps = <0>; /* -420ps */ |
| 85 |
rxd0-skew-ps = <420>; /* 0ps */ |
| 86 |
rxd1-skew-ps = <420>; /* 0ps */ |
| 87 |
rxd2-skew-ps = <420>; /* 0ps */ |
| 88 |
rxd3-skew-ps = <420>; /* 0ps */ |
| 89 |
txen-skew-ps = <0>; /* -420ps */ |
| 90 |
txc-skew-ps = <1860>; /* 960ps */ |
| 91 |
rxdv-skew-ps = <420>; /* 0ps */ |
| 92 |
rxc-skew-ps = <1680>; /* 780ps */ |
| 93 |
max-frame-size = <3800>; |
| 94 |
status = "okay"; |
| 95 |
}; |
| 96 |
|
| 97 |
&gpio1 { |
| 98 |
status = "okay"; |
| 99 |
}; |
| 100 |
|
| 101 |
&spi1 { |
| 102 |
status = "okay"; |
| 103 |
|
| 104 |
resource-manager@0 { |
| 105 |
compatible = "altr,a10sr"; |
| 106 |
reg = <0>; |
| 107 |
spi-max-frequency = <100000>; |
| 108 |
/* low-level active IRQ at GPIO1_5 */ |
| 109 |
interrupt-parent = <&portb>; |
| 110 |
interrupts = <5 IRQ_TYPE_LEVEL_LOW>; |
| 111 |
interrupt-controller; |
| 112 |
#interrupt-cells = <2>; |
| 113 |
|
| 114 |
a10sr_gpio: gpio-controller { |
| 115 |
compatible = "altr,a10sr-gpio"; |
| 116 |
gpio-controller; |
| 117 |
#gpio-cells = <2>; |
| 118 |
}; |
| 119 |
|
| 120 |
a10sr_rst: reset-controller { |
| 121 |
compatible = "altr,a10sr-reset"; |
| 122 |
#reset-cells = <1>; |
| 123 |
}; |
| 124 |
}; |
| 125 |
}; |
| 126 |
|
| 127 |
&i2c1 { |
| 128 |
status = "okay"; |
| 129 |
|
| 130 |
/* |
| 131 |
* adjust the falling times to decrease the i2c frequency to 50Khz |
| 132 |
* because the LCD module does not work at the standard 100Khz |
| 133 |
*/ |
| 134 |
clock-frequency = <100000>; |
| 135 |
i2c-sda-falling-time-ns = <6000>; |
| 136 |
i2c-scl-falling-time-ns = <6000>; |
| 137 |
|
| 138 |
adc@14 { |
| 139 |
compatible = "lltc,ltc2497"; |
| 140 |
reg = <0x14>; |
| 141 |
vref-supply = <&ref_033v>; |
| 142 |
}; |
| 143 |
|
| 144 |
adc@16 { |
| 145 |
compatible = "lltc,ltc2497"; |
| 146 |
reg = <0x16>; |
| 147 |
vref-supply = <&ref_033v>; |
| 148 |
}; |
| 149 |
|
| 150 |
eeprom@51 { |
| 151 |
compatible = "atmel,24c32"; |
| 152 |
reg = <0x51>; |
| 153 |
pagesize = <32>; |
| 154 |
}; |
| 155 |
|
| 156 |
rtc@68 { |
| 157 |
compatible = "dallas,ds1339"; |
| 158 |
reg = <0x68>; |
| 159 |
}; |
| 160 |
|
| 161 |
ltc@5c { |
| 162 |
compatible = "ltc2977"; |
| 163 |
reg = <0x5c>; |
| 164 |
}; |
| 165 |
|
| 166 |
temp@4c { |
| 167 |
compatible = "maxim,max1619"; |
| 168 |
reg = <0x4c>; |
| 169 |
}; |
| 170 |
}; |
| 171 |
|
| 172 |
&uart1 { |
| 173 |
status = "okay"; |
| 174 |
}; |
| 175 |
|
| 176 |
&usb0 { |
| 177 |
status = "okay"; |
| 178 |
disable-over-current; |
| 179 |
}; |
| 180 |
|
| 181 |
&watchdog1 { |
| 182 |
status = "okay"; |
| 183 |
}; |