| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* |
| 3 |
* Device Tree file for ITian Square One SQ201 NAS |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include "gemini.dtsi" |
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "ITian Square One SQ201"; |
| 13 |
compatible = "itian,sq201", "cortina,gemini"; |
| 14 |
#address-cells = <1>; |
| 15 |
#size-cells = <1>; |
| 16 |
|
| 17 |
memory@0 { /* 128 MB */ |
| 18 |
device_type = "memory"; |
| 19 |
reg = <0x00000000 0x8000000>; |
| 20 |
}; |
| 21 |
|
| 22 |
chosen { |
| 23 |
bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait"; |
| 24 |
stdout-path = &uart0; |
| 25 |
}; |
| 26 |
|
| 27 |
gpio_keys { |
| 28 |
compatible = "gpio-keys"; |
| 29 |
|
| 30 |
button-setup { |
| 31 |
debounce-interval = <100>; |
| 32 |
wakeup-source; |
| 33 |
linux,code = <KEY_RESTART>; |
| 34 |
label = "factory reset"; |
| 35 |
/* Conflict with NAND flash */ |
| 36 |
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>; |
| 37 |
}; |
| 38 |
}; |
| 39 |
|
| 40 |
leds { |
| 41 |
compatible = "gpio-leds"; |
| 42 |
led-green-info { |
| 43 |
label = "sq201:green:info"; |
| 44 |
gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>; |
| 45 |
default-state = "on"; |
| 46 |
linux,default-trigger = "heartbeat"; |
| 47 |
}; |
| 48 |
led-green-usb { |
| 49 |
label = "sq201:green:usb"; |
| 50 |
gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; |
| 51 |
default-state = "off"; |
| 52 |
linux,default-trigger = "usb-host"; |
| 53 |
}; |
| 54 |
}; |
| 55 |
|
| 56 |
mdio0: mdio { |
| 57 |
compatible = "virtual,mdio-gpio"; |
| 58 |
/* Uses MDC and MDIO */ |
| 59 |
gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */ |
| 60 |
<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */ |
| 61 |
#address-cells = <1>; |
| 62 |
#size-cells = <0>; |
| 63 |
|
| 64 |
/* This is a Marvell 88E1111 ethernet transciever */ |
| 65 |
phy0: ethernet-phy@1 { |
| 66 |
reg = <1>; |
| 67 |
}; |
| 68 |
}; |
| 69 |
|
| 70 |
spi { |
| 71 |
compatible = "spi-gpio"; |
| 72 |
#address-cells = <1>; |
| 73 |
#size-cells = <0>; |
| 74 |
/* Check pin collisions */ |
| 75 |
sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; |
| 76 |
miso-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>; |
| 77 |
mosi-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>; |
| 78 |
cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>; |
| 79 |
num-chipselects = <1>; |
| 80 |
|
| 81 |
ethernet-switch@0 { |
| 82 |
compatible = "vitesse,vsc7395"; |
| 83 |
reg = <0>; |
| 84 |
/* Specified for 2.5 MHz or below */ |
| 85 |
spi-max-frequency = <2500000>; |
| 86 |
gpio-controller; |
| 87 |
#gpio-cells = <2>; |
| 88 |
|
| 89 |
ethernet-ports { |
| 90 |
#address-cells = <1>; |
| 91 |
#size-cells = <0>; |
| 92 |
|
| 93 |
ethernet-port@0 { |
| 94 |
reg = <0>; |
| 95 |
label = "lan1"; |
| 96 |
}; |
| 97 |
ethernet-port@1 { |
| 98 |
reg = <1>; |
| 99 |
label = "lan2"; |
| 100 |
}; |
| 101 |
ethernet-port@2 { |
| 102 |
reg = <2>; |
| 103 |
label = "lan3"; |
| 104 |
}; |
| 105 |
ethernet-port@3 { |
| 106 |
reg = <3>; |
| 107 |
label = "lan4"; |
| 108 |
}; |
| 109 |
vsc: ethernet-port@6 { |
| 110 |
reg = <6>; |
| 111 |
label = "cpu"; |
| 112 |
ethernet = <&gmac1>; |
| 113 |
phy-mode = "rgmii"; |
| 114 |
fixed-link { |
| 115 |
speed = <1000>; |
| 116 |
full-duplex; |
| 117 |
pause; |
| 118 |
}; |
| 119 |
}; |
| 120 |
}; |
| 121 |
}; |
| 122 |
}; |
| 123 |
|
| 124 |
|
| 125 |
soc { |
| 126 |
flash@30000000 { |
| 127 |
status = "okay"; |
| 128 |
pinctrl-names = "enabled", "disabled"; |
| 129 |
pinctrl-0 = <&pflash_default_pins>; |
| 130 |
pinctrl-1 = <&pflash_disabled_pins>; |
| 131 |
/* 16MB of flash */ |
| 132 |
reg = <0x30000000 0x01000000>; |
| 133 |
|
| 134 |
partitions { |
| 135 |
compatible = "redboot-fis"; |
| 136 |
/* Eraseblock at 0xfe0000 */ |
| 137 |
fis-index-block = <0x1fc>; |
| 138 |
}; |
| 139 |
}; |
| 140 |
|
| 141 |
syscon: syscon@40000000 { |
| 142 |
pinctrl { |
| 143 |
/* |
| 144 |
* gpio0fgrp cover line 18 used by reset button |
| 145 |
* gpio0ggrp cover line 20 used by info LED |
| 146 |
* gpio0hgrp cover line 21, 22 used by MDIO for Marvell PHY |
| 147 |
* gpio0kgrp cover line 31 used by USB LED |
| 148 |
*/ |
| 149 |
gpio0_default_pins: pinctrl-gpio0 { |
| 150 |
mux { |
| 151 |
function = "gpio0"; |
| 152 |
groups = "gpio0fgrp", |
| 153 |
"gpio0hgrp"; |
| 154 |
}; |
| 155 |
}; |
| 156 |
/* |
| 157 |
* gpio0dgrp cover lines used by the SPI |
| 158 |
* to the Vitesse G5x chip. |
| 159 |
*/ |
| 160 |
gpio1_default_pins: pinctrl-gpio1 { |
| 161 |
mux { |
| 162 |
function = "gpio1"; |
| 163 |
groups = "gpio1dgrp"; |
| 164 |
}; |
| 165 |
}; |
| 166 |
/* |
| 167 |
* These GPIO groups will be mapped in over some |
| 168 |
* of the flash pins when the flash is not in |
| 169 |
* active use. |
| 170 |
*/ |
| 171 |
pflash_disabled_pins: pinctrl-pflash-disabled { |
| 172 |
mux { |
| 173 |
function = "gpio0"; |
| 174 |
groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp", |
| 175 |
"gpio0kgrp"; |
| 176 |
}; |
| 177 |
}; |
| 178 |
pinctrl-gmii { |
| 179 |
mux { |
| 180 |
function = "gmii"; |
| 181 |
groups = "gmii_gmac0_grp", "gmii_gmac1_grp"; |
| 182 |
}; |
| 183 |
/* Settings come from memory dump in PLATO */ |
| 184 |
conf0 { |
| 185 |
pins = "V8 GMAC0 RXDV"; |
| 186 |
skew-delay = <0>; |
| 187 |
}; |
| 188 |
conf1 { |
| 189 |
pins = "Y7 GMAC0 RXC"; |
| 190 |
skew-delay = <15>; |
| 191 |
}; |
| 192 |
conf2 { |
| 193 |
pins = "T8 GMAC0 TXEN"; |
| 194 |
skew-delay = <7>; |
| 195 |
}; |
| 196 |
conf3 { |
| 197 |
pins = "U8 GMAC0 TXC"; |
| 198 |
skew-delay = <10>; |
| 199 |
}; |
| 200 |
conf4 { |
| 201 |
pins = "T10 GMAC1 RXDV"; |
| 202 |
skew-delay = <7>; |
| 203 |
}; |
| 204 |
conf5 { |
| 205 |
pins = "Y11 GMAC1 RXC"; |
| 206 |
skew-delay = <8>; |
| 207 |
}; |
| 208 |
conf6 { |
| 209 |
pins = "W11 GMAC1 TXEN"; |
| 210 |
skew-delay = <7>; |
| 211 |
}; |
| 212 |
conf7 { |
| 213 |
pins = "V11 GMAC1 TXC"; |
| 214 |
skew-delay = <5>; |
| 215 |
}; |
| 216 |
conf8 { |
| 217 |
/* The data lines all have default skew */ |
| 218 |
pins = "W8 GMAC0 RXD0", "V9 GMAC0 RXD1", |
| 219 |
"Y8 GMAC0 RXD2", "U9 GMAC0 RXD3", |
| 220 |
"T7 GMAC0 TXD0", "U6 GMAC0 TXD1", |
| 221 |
"V7 GMAC0 TXD2", "U7 GMAC0 TXD3", |
| 222 |
"Y12 GMAC1 RXD0", "V12 GMAC1 RXD1", |
| 223 |
"T11 GMAC1 RXD2", "W12 GMAC1 RXD3", |
| 224 |
"U10 GMAC1 TXD0", "Y10 GMAC1 TXD1", |
| 225 |
"W10 GMAC1 TXD2", "T9 GMAC1 TXD3"; |
| 226 |
skew-delay = <7>; |
| 227 |
}; |
| 228 |
/* Set up drive strength on GMAC0 and GMAC1 to 16 mA */ |
| 229 |
conf9 { |
| 230 |
groups = "gmii_gmac0_grp", "gmii_gmac1_grp"; |
| 231 |
drive-strength = <16>; |
| 232 |
}; |
| 233 |
}; |
| 234 |
}; |
| 235 |
}; |
| 236 |
|
| 237 |
sata: sata@46000000 { |
| 238 |
cortina,gemini-ata-muxmode = <0>; |
| 239 |
cortina,gemini-enable-sata-bridge; |
| 240 |
status = "okay"; |
| 241 |
}; |
| 242 |
|
| 243 |
gpio0: gpio@4d000000 { |
| 244 |
pinctrl-names = "default"; |
| 245 |
pinctrl-0 = <&gpio0_default_pins>; |
| 246 |
}; |
| 247 |
|
| 248 |
gpio1: gpio@4e000000 { |
| 249 |
pinctrl-names = "default"; |
| 250 |
pinctrl-0 = <&gpio1_default_pins>; |
| 251 |
}; |
| 252 |
|
| 253 |
pci@50000000 { |
| 254 |
status = "okay"; |
| 255 |
}; |
| 256 |
|
| 257 |
ethernet@60000000 { |
| 258 |
status = "okay"; |
| 259 |
|
| 260 |
ethernet-port@0 { |
| 261 |
phy-mode = "rgmii"; |
| 262 |
phy-handle = <&phy0>; |
| 263 |
}; |
| 264 |
ethernet-port@1 { |
| 265 |
phy-mode = "rgmii"; |
| 266 |
fixed-link { |
| 267 |
speed = <1000>; |
| 268 |
full-duplex; |
| 269 |
pause; |
| 270 |
}; |
| 271 |
}; |
| 272 |
}; |
| 273 |
|
| 274 |
ide@63000000 { |
| 275 |
status = "okay"; |
| 276 |
}; |
| 277 |
|
| 278 |
usb@68000000 { |
| 279 |
status = "okay"; |
| 280 |
}; |
| 281 |
|
| 282 |
usb@69000000 { |
| 283 |
status = "okay"; |
| 284 |
}; |
| 285 |
}; |
| 286 |
}; |