| 1 |
/* |
| 2 |
* Device Tree file for D-Link DIR-685 Xtreme N Storage Router |
| 3 |
*/ |
| 4 |
|
| 5 |
/dts-v1/; |
| 6 |
|
| 7 |
#include "gemini.dtsi" |
| 8 |
#include <dt-bindings/input/input.h> |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "D-Link DIR-685 Xtreme N Storage Router"; |
| 12 |
compatible = "dlink,dir-685", "cortina,gemini"; |
| 13 |
#address-cells = <1>; |
| 14 |
#size-cells = <1>; |
| 15 |
|
| 16 |
memory@0 { |
| 17 |
/* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */ |
| 18 |
device_type = "memory"; |
| 19 |
reg = <0x00000000 0x8000000>; |
| 20 |
}; |
| 21 |
|
| 22 |
chosen { |
| 23 |
bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait consoleblank=300"; |
| 24 |
stdout-path = "uart0:19200n8"; |
| 25 |
}; |
| 26 |
|
| 27 |
gpio_keys { |
| 28 |
compatible = "gpio-keys"; |
| 29 |
|
| 30 |
button-reset { |
| 31 |
debounce-interval = <100>; |
| 32 |
wakeup-source; |
| 33 |
linux,code = <KEY_RESTART>; |
| 34 |
label = "reset"; |
| 35 |
/* Collides with LPC_LAD[0], UART DCD, SSP 97RST */ |
| 36 |
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; |
| 37 |
}; |
| 38 |
button-eject { |
| 39 |
debounce-interval = <100>; |
| 40 |
wakeup-source; |
| 41 |
linux,code = <KEY_EJECTCD>; |
| 42 |
label = "unmount"; |
| 43 |
/* Collides with LPC LFRAME, UART RTS, SSP TXD */ |
| 44 |
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
| 45 |
}; |
| 46 |
}; |
| 47 |
|
| 48 |
vdisp: regulator { |
| 49 |
compatible = "regulator-fixed"; |
| 50 |
regulator-name = "display-power"; |
| 51 |
regulator-min-microvolt = <3600000>; |
| 52 |
regulator-max-microvolt = <3600000>; |
| 53 |
/* Collides with LCD E */ |
| 54 |
gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>; |
| 55 |
enable-active-high; |
| 56 |
}; |
| 57 |
|
| 58 |
spi { |
| 59 |
compatible = "spi-gpio"; |
| 60 |
#address-cells = <1>; |
| 61 |
#size-cells = <0>; |
| 62 |
|
| 63 |
/* Collides with IDE pins, that's cool (we do not use them) */ |
| 64 |
sck-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; |
| 65 |
miso-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; |
| 66 |
mosi-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; |
| 67 |
cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; |
| 68 |
num-chipselects = <1>; |
| 69 |
|
| 70 |
panel: display@0 { |
| 71 |
compatible = "dlink,dir-685-panel", "ilitek,ili9322"; |
| 72 |
reg = <0>; |
| 73 |
/* 50 ns min period = 20 MHz */ |
| 74 |
spi-max-frequency = <20000000>; |
| 75 |
vcc-supply = <&vdisp>; |
| 76 |
iovcc-supply = <&vdisp>; |
| 77 |
vci-supply = <&vdisp>; |
| 78 |
|
| 79 |
port { |
| 80 |
panel_in: endpoint { |
| 81 |
remote-endpoint = <&display_out>; |
| 82 |
}; |
| 83 |
}; |
| 84 |
}; |
| 85 |
}; |
| 86 |
|
| 87 |
leds { |
| 88 |
compatible = "gpio-leds"; |
| 89 |
led-wps { |
| 90 |
label = "dir685:blue:WPS"; |
| 91 |
/* Collides with ICE */ |
| 92 |
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; |
| 93 |
default-state = "on"; |
| 94 |
linux,default-trigger = "heartbeat"; |
| 95 |
}; |
| 96 |
/* |
| 97 |
* These two LEDs are on the side of the device. |
| 98 |
* For electrical reasons, both LEDs cannot be active |
| 99 |
* at the same time so only blue or orange can be on at |
| 100 |
* one time. Enabling both makes the LED go dark. |
| 101 |
* The LEDs both sit inside the unmount button and the |
| 102 |
* label on the case says "unmount". |
| 103 |
*/ |
| 104 |
led-blue-hd { |
| 105 |
label = "dir685:blue:HD"; |
| 106 |
/* Collides with LPC_SERIRQ, UART DTR, SSP FSC pins */ |
| 107 |
gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; |
| 108 |
default-state = "off"; |
| 109 |
linux,default-trigger = "disk-read"; |
| 110 |
}; |
| 111 |
led-orange-hd { |
| 112 |
label = "dir685:orange:HD"; |
| 113 |
/* Collides with LPC_LAD[2], UART DSR, SSP ECLK pins */ |
| 114 |
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; |
| 115 |
default-state = "off"; |
| 116 |
linux,default-trigger = "disk-write"; |
| 117 |
}; |
| 118 |
}; |
| 119 |
|
| 120 |
/* |
| 121 |
* This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM. |
| 122 |
* sensor. It is turned on when the temperature exceeds 46 degrees |
| 123 |
* and turned off when the temperatures goes below 41 degrees |
| 124 |
* (celsius). |
| 125 |
*/ |
| 126 |
fan0: gpio-fan { |
| 127 |
compatible = "gpio-fan"; |
| 128 |
/* Collides with IDE */ |
| 129 |
gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; |
| 130 |
gpio-fan,speed-map = <0 0>, <10000 1>; |
| 131 |
#cooling-cells = <2>; |
| 132 |
}; |
| 133 |
|
| 134 |
thermal-zones { |
| 135 |
chassis-thermal { |
| 136 |
/* Poll every 20 seconds */ |
| 137 |
polling-delay = <20000>; |
| 138 |
/* Poll every 2nd second when cooling */ |
| 139 |
polling-delay-passive = <2000>; |
| 140 |
/* Use the thermal sensor in the hard drive */ |
| 141 |
thermal-sensors = <&drive0>; |
| 142 |
|
| 143 |
/* Tripping points from the fan.script in the rootfs */ |
| 144 |
trips { |
| 145 |
alert: chassis-alert { |
| 146 |
/* At 43 degrees turn on the fan */ |
| 147 |
temperature = <43000>; |
| 148 |
hysteresis = <3000>; |
| 149 |
type = "active"; |
| 150 |
}; |
| 151 |
crit: chassis-crit { |
| 152 |
/* Just shut down at 60 degrees */ |
| 153 |
temperature = <60000>; |
| 154 |
hysteresis = <2000>; |
| 155 |
type = "critical"; |
| 156 |
}; |
| 157 |
}; |
| 158 |
|
| 159 |
cooling-maps { |
| 160 |
map0 { |
| 161 |
trip = <&alert>; |
| 162 |
cooling-device = <&fan0 1 1>; |
| 163 |
}; |
| 164 |
}; |
| 165 |
}; |
| 166 |
}; |
| 167 |
|
| 168 |
/* |
| 169 |
* The touchpad input is connected to a GPIO bit-banged |
| 170 |
* I2C bus. |
| 171 |
*/ |
| 172 |
i2c { |
| 173 |
compatible = "i2c-gpio"; |
| 174 |
/* Collides with ICE */ |
| 175 |
sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 176 |
scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 177 |
#address-cells = <1>; |
| 178 |
#size-cells = <0>; |
| 179 |
|
| 180 |
touchkeys@26 { |
| 181 |
compatible = "dlink,dir685-touchkeys"; |
| 182 |
reg = <0x26>; |
| 183 |
interrupt-parent = <&gpio0>; |
| 184 |
/* Collides with NAND flash */ |
| 185 |
interrupts = <17 IRQ_TYPE_EDGE_FALLING>; |
| 186 |
}; |
| 187 |
}; |
| 188 |
|
| 189 |
/* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */ |
| 190 |
ethernet-switch { |
| 191 |
compatible = "realtek,rtl8366rb"; |
| 192 |
/* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ |
| 193 |
mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; |
| 194 |
mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; |
| 195 |
reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; |
| 196 |
realtek,disable-leds; |
| 197 |
|
| 198 |
switch_intc: interrupt-controller { |
| 199 |
/* GPIO 15 provides the interrupt */ |
| 200 |
interrupt-parent = <&gpio0>; |
| 201 |
interrupts = <15 IRQ_TYPE_LEVEL_LOW>; |
| 202 |
interrupt-controller; |
| 203 |
#address-cells = <0>; |
| 204 |
#interrupt-cells = <1>; |
| 205 |
}; |
| 206 |
|
| 207 |
ethernet-ports { |
| 208 |
#address-cells = <1>; |
| 209 |
#size-cells = <0>; |
| 210 |
|
| 211 |
ethernet-port@0 { |
| 212 |
reg = <0>; |
| 213 |
label = "lan0"; |
| 214 |
phy-handle = <&phy0>; |
| 215 |
}; |
| 216 |
ethernet-port@1 { |
| 217 |
reg = <1>; |
| 218 |
label = "lan1"; |
| 219 |
phy-handle = <&phy1>; |
| 220 |
}; |
| 221 |
ethernet-port@2 { |
| 222 |
reg = <2>; |
| 223 |
label = "lan2"; |
| 224 |
phy-handle = <&phy2>; |
| 225 |
}; |
| 226 |
ethernet-port@3 { |
| 227 |
reg = <3>; |
| 228 |
label = "lan3"; |
| 229 |
phy-handle = <&phy3>; |
| 230 |
}; |
| 231 |
ethernet-port@4 { |
| 232 |
reg = <4>; |
| 233 |
label = "wan"; |
| 234 |
phy-handle = <&phy4>; |
| 235 |
}; |
| 236 |
rtl8366rb_cpu_port: ethernet-port@5 { |
| 237 |
reg = <5>; |
| 238 |
label = "cpu"; |
| 239 |
ethernet = <&gmac0>; |
| 240 |
phy-mode = "rgmii"; |
| 241 |
fixed-link { |
| 242 |
speed = <1000>; |
| 243 |
full-duplex; |
| 244 |
pause; |
| 245 |
}; |
| 246 |
}; |
| 247 |
|
| 248 |
}; |
| 249 |
|
| 250 |
mdio { |
| 251 |
compatible = "realtek,smi-mdio"; |
| 252 |
#address-cells = <1>; |
| 253 |
#size-cells = <0>; |
| 254 |
|
| 255 |
phy0: ethernet-phy@0 { |
| 256 |
reg = <0>; |
| 257 |
interrupt-parent = <&switch_intc>; |
| 258 |
interrupts = <0>; |
| 259 |
}; |
| 260 |
phy1: ethernet-phy@1 { |
| 261 |
reg = <1>; |
| 262 |
interrupt-parent = <&switch_intc>; |
| 263 |
interrupts = <1>; |
| 264 |
}; |
| 265 |
phy2: ethernet-phy@2 { |
| 266 |
reg = <2>; |
| 267 |
interrupt-parent = <&switch_intc>; |
| 268 |
interrupts = <2>; |
| 269 |
}; |
| 270 |
phy3: ethernet-phy@3 { |
| 271 |
reg = <3>; |
| 272 |
interrupt-parent = <&switch_intc>; |
| 273 |
interrupts = <3>; |
| 274 |
}; |
| 275 |
phy4: ethernet-phy@4 { |
| 276 |
reg = <4>; |
| 277 |
interrupt-parent = <&switch_intc>; |
| 278 |
interrupts = <12>; |
| 279 |
}; |
| 280 |
}; |
| 281 |
}; |
| 282 |
|
| 283 |
soc { |
| 284 |
flash@30000000 { |
| 285 |
/* |
| 286 |
* Flash access collides with the Chip Enable signal for |
| 287 |
* the display panel, that reuse the parallel flash Chip |
| 288 |
* Select 1 (CS1). We switch the pin control state so we |
| 289 |
* enable these pins for flash access only when we need |
| 290 |
* then, and when disabled they can be used for GPIO which |
| 291 |
* is what the display panel needs. |
| 292 |
*/ |
| 293 |
status = "okay"; |
| 294 |
pinctrl-names = "enabled", "disabled"; |
| 295 |
pinctrl-0 = <&pflash_default_pins>; |
| 296 |
pinctrl-1 = <&pflash_disabled_pins>; |
| 297 |
|
| 298 |
/* 32MB of flash */ |
| 299 |
reg = <0x30000000 0x02000000>; |
| 300 |
|
| 301 |
partitions { |
| 302 |
compatible = "fixed-partitions"; |
| 303 |
#address-cells = <1>; |
| 304 |
#size-cells = <1>; |
| 305 |
|
| 306 |
/* |
| 307 |
* This "RedBoot" is the Storlink derivative. |
| 308 |
*/ |
| 309 |
partition@0 { |
| 310 |
label = "RedBoot"; |
| 311 |
reg = <0x00000000 0x00040000>; |
| 312 |
read-only; |
| 313 |
}; |
| 314 |
/* |
| 315 |
* This firmware image contains the kernel catenated |
| 316 |
* with the squashfs root filesystem. For some reason |
| 317 |
* this is called "upgrade" on the vendor system. |
| 318 |
*/ |
| 319 |
partition@40000 { |
| 320 |
label = "upgrade"; |
| 321 |
reg = <0x00040000 0x01f40000>; |
| 322 |
read-only; |
| 323 |
}; |
| 324 |
/* RGDB, Residental Gateway Database? */ |
| 325 |
partition@1f80000 { |
| 326 |
label = "rgdb"; |
| 327 |
reg = <0x01f80000 0x00040000>; |
| 328 |
read-only; |
| 329 |
}; |
| 330 |
/* |
| 331 |
* This partition contains MAC addresses for WAN, |
| 332 |
* WLAN and LAN, and the country code (for wireless |
| 333 |
* I guess). |
| 334 |
*/ |
| 335 |
partition@1fc0000 { |
| 336 |
label = "nvram"; |
| 337 |
reg = <0x01fc0000 0x00020000>; |
| 338 |
read-only; |
| 339 |
}; |
| 340 |
partition@1fe0000 { |
| 341 |
label = "LangPack"; |
| 342 |
reg = <0x01fe0000 0x00020000>; |
| 343 |
read-only; |
| 344 |
}; |
| 345 |
}; |
| 346 |
}; |
| 347 |
|
| 348 |
syscon: syscon@40000000 { |
| 349 |
pinctrl { |
| 350 |
/* |
| 351 |
* gpio0bgrp cover line 5, 6 used by TK I2C |
| 352 |
* gpio0bgrp cover line 7 used by WPS LED |
| 353 |
* gpio0cgrp cover line 8, 13 used by keys |
| 354 |
* and 11, 12 used by the HD LEDs |
| 355 |
* and line 14, 15 used by RTL8366 |
| 356 |
* RESET and phy ready |
| 357 |
* gpio0egrp cover line 16 used by VDISP |
| 358 |
* gpio0fgrp cover line 17 used by TK IRQ |
| 359 |
* gpio0ggrp cover line 20 used by panel CS |
| 360 |
* gpio0hgrp cover line 21,22 used by RTL8366RB MDIO |
| 361 |
*/ |
| 362 |
gpio0_default_pins: pinctrl-gpio0 { |
| 363 |
mux { |
| 364 |
function = "gpio0"; |
| 365 |
groups = "gpio0bgrp", |
| 366 |
"gpio0cgrp", |
| 367 |
"gpio0egrp", |
| 368 |
"gpio0fgrp", |
| 369 |
"gpio0hgrp"; |
| 370 |
}; |
| 371 |
}; |
| 372 |
/* |
| 373 |
* gpio1bgrp cover line 5,8,7 used by panel SPI |
| 374 |
* also line 6 used by the fan |
| 375 |
* |
| 376 |
*/ |
| 377 |
gpio1_default_pins: pinctrl-gpio1 { |
| 378 |
mux { |
| 379 |
function = "gpio1"; |
| 380 |
groups = "gpio1bgrp"; |
| 381 |
}; |
| 382 |
}; |
| 383 |
/* |
| 384 |
* These GPIO groups will be mapped in over some |
| 385 |
* of the flash pins when the flash is not in |
| 386 |
* active use. |
| 387 |
*/ |
| 388 |
pflash_disabled_pins: pinctrl-pflash-disabled { |
| 389 |
mux { |
| 390 |
function = "gpio0"; |
| 391 |
groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp", |
| 392 |
"gpio0kgrp"; |
| 393 |
}; |
| 394 |
}; |
| 395 |
pinctrl-gmii { |
| 396 |
mux { |
| 397 |
function = "gmii"; |
| 398 |
groups = "gmii_gmac0_grp"; |
| 399 |
}; |
| 400 |
conf0 { |
| 401 |
pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV", |
| 402 |
"Y7 GMAC0 RXC", "Y11 GMAC1 RXC", |
| 403 |
"T8 GMAC0 TXEN", "W11 GMAC1 TXEN", |
| 404 |
"U8 GMAC0 TXC", "V11 GMAC1 TXC", |
| 405 |
"W8 GMAC0 RXD0", "V9 GMAC0 RXD1", |
| 406 |
"Y8 GMAC0 RXD2", "U9 GMAC0 RXD3", |
| 407 |
"T7 GMAC0 TXD0", "U6 GMAC0 TXD1", |
| 408 |
"V7 GMAC0 TXD2", "U7 GMAC0 TXD3", |
| 409 |
"Y12 GMAC1 RXD0", "V12 GMAC1 RXD1", |
| 410 |
"T11 GMAC1 RXD2", "W12 GMAC1 RXD3", |
| 411 |
"U10 GMAC1 TXD0", "Y10 GMAC1 TXD1", |
| 412 |
"W10 GMAC1 TXD2", "T9 GMAC1 TXD3"; |
| 413 |
skew-delay = <7>; |
| 414 |
}; |
| 415 |
/* Set up drive strength on GMAC0 to 16 mA */ |
| 416 |
conf1 { |
| 417 |
groups = "gmii_gmac0_grp"; |
| 418 |
drive-strength = <16>; |
| 419 |
}; |
| 420 |
}; |
| 421 |
}; |
| 422 |
}; |
| 423 |
|
| 424 |
sata: sata@46000000 { |
| 425 |
cortina,gemini-ata-muxmode = <0>; |
| 426 |
cortina,gemini-enable-sata-bridge; |
| 427 |
status = "okay"; |
| 428 |
}; |
| 429 |
|
| 430 |
gpio0: gpio@4d000000 { |
| 431 |
pinctrl-names = "default"; |
| 432 |
pinctrl-0 = <&gpio0_default_pins>; |
| 433 |
}; |
| 434 |
|
| 435 |
gpio1: gpio@4e000000 { |
| 436 |
pinctrl-names = "default"; |
| 437 |
pinctrl-0 = <&gpio1_default_pins>; |
| 438 |
}; |
| 439 |
|
| 440 |
pci@50000000 { |
| 441 |
status = "okay"; |
| 442 |
}; |
| 443 |
|
| 444 |
ethernet@60000000 { |
| 445 |
status = "okay"; |
| 446 |
|
| 447 |
ethernet-port@0 { |
| 448 |
phy-mode = "rgmii"; |
| 449 |
fixed-link { |
| 450 |
speed = <1000>; |
| 451 |
full-duplex; |
| 452 |
pause; |
| 453 |
}; |
| 454 |
}; |
| 455 |
ethernet-port@1 { |
| 456 |
/* Not used in this platform */ |
| 457 |
}; |
| 458 |
}; |
| 459 |
|
| 460 |
ide@63000000 { |
| 461 |
status = "okay"; |
| 462 |
|
| 463 |
/* |
| 464 |
* This drive may have a temperature sensor with a |
| 465 |
* thermal zone we can use for thermal control of the |
| 466 |
* chassis temperature using the fan. |
| 467 |
*/ |
| 468 |
drive0: ide-port@0 { |
| 469 |
reg = <0>; |
| 470 |
#thermal-sensor-cells = <0>; |
| 471 |
}; |
| 472 |
}; |
| 473 |
|
| 474 |
display-controller@6a000000 { |
| 475 |
status = "okay"; |
| 476 |
|
| 477 |
port { |
| 478 |
display_out: endpoint { |
| 479 |
remote-endpoint = <&panel_in>; |
| 480 |
}; |
| 481 |
}; |
| 482 |
}; |
| 483 |
|
| 484 |
usb@68000000 { |
| 485 |
status = "okay"; |
| 486 |
}; |
| 487 |
|
| 488 |
usb@69000000 { |
| 489 |
status = "okay"; |
| 490 |
}; |
| 491 |
}; |
| 492 |
}; |