| 1 |
Basic SEC-SAXS processing |
| 2 |
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| 3 |
.. _s1p7: |
| 4 |
|
| 5 |
In a typical SEC-SAXS run, images are continuously collected while the eluate (outflow) |
| 6 |
of a size exclusion column flows through the SAXS sample cell. As proteins scatter more |
| 7 |
strongly than buffer, a plot of total scattered intensity vs. time, the so-called SAXS |
| 8 |
chromatograph (or scattergram), will show a set of peaks similar to what is seen by |
| 9 |
UV absorption measurement of the SEC system. RAW includes the capability to do routine |
| 10 |
processing of SEC-SAXS data. This includes creating the SAXS chromatograph from the data, |
| 11 |
plotting |Rg|, MW, and I(0) across the peaks, and extracting specific frames for further analysis. |
| 12 |
|
| 13 |
*Note:* In RAW, this is called Series analysis, as the same tools can be used for other |
| 14 |
sequentially sampled data sets. |
| 15 |
|
| 16 |
A video version of this tutorial is available: |
| 17 |
|
| 18 |
.. raw:: html |
| 19 |
|
| 20 |
<style>.embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }</style><div class='embed-container'><iframe src='https://www.youtube.com/embed/3aJl2kNBPuA' frameborder='0' allowfullscreen></iframe></div> |
| 21 |
|
| 22 |
The written version of the tutorial follows. |
| 23 |
|
| 24 |
#. Clear any data loaded into RAW. |
| 25 |
|
| 26 |
* *Tip:* In the Files tab, click the “Clear All” button to clear all data in RAW. |
| 27 |
|
| 28 |
#. Go to the Files control tab and navigate to the **sec_sample_1** data directory. |
| 29 |
|
| 30 |
#. Click on the first data file, **profile_001_0000.dat**\ . Scroll down to the |
| 31 |
bottom of the file list, and shift click on the last file, |
| 32 |
**profile_001_0964.dat**\ . This should highlight all of the files in |
| 33 |
between, as well as the two you clicked on. Click on the "Plot Series" |
| 34 |
button to load the series into RAW. |
| 35 |
|
| 36 |
|series_load1_png| |
| 37 |
|
| 38 |
#. RAW should automatically show you the Series plot panel. If not, click |
| 39 |
on the Series tab in the plot. Click on the Series tab in the control panel. |
| 40 |
|
| 41 |
|series_plot_png| |
| 42 |
|
| 43 |
* *Try:* Each point on this curve is the integrated intensity of a scattering profile. |
| 44 |
You can figure out which one by right clicking on the filename in the Series list and |
| 45 |
selecting ‘Show data’. This will show you the frame number and integrated intensity |
| 46 |
displayed on the plot, and the filename corresponding to the displayed frame number. |
| 47 |
|
| 48 |
#. Drag the plot so that you can clearly the see the first frame. You’ll notice it has a |
| 49 |
significantly lower intensity than the rest of the frames. This happens occasionally |
| 50 |
at the MacCHESS G1 beamline (where the data was taken). It can make it harder to tell |
| 51 |
what the data is doing. |
| 52 |
|
| 53 |
* *Tip:* Select the crossed arrows in the plot control bar, and then click and drag on |
| 54 |
the plot to move the curve around on the screen. |
| 55 |
|
| 56 |
#. Reload the data as in steps 2-3, but select the second data file, |
| 57 |
**profile_001_0001.dat** as the initial file in the series. |
| 58 |
|
| 59 |
* *Tip:* As before, select **profile_001_0001.dat**, scroll down |
| 60 |
to the last file, and shift click to select the files to load |
| 61 |
in. Then click the "Plot Series" button. |
| 62 |
|
| 63 |
#. You will see the same curve plotted as before, but without the very first |
| 64 |
scattering profile. Remove the other loaded data set. Now you should have |
| 65 |
a curve where the baseline is very close to the bottom of the plot. |
| 66 |
|
| 67 |
|series_plot2_png| |
| 68 |
|
| 69 |
#. In some cases it is more useful to look at the mean intensity, the intensity at a |
| 70 |
specific *q* value, or the intensity in a range of *q* values than the total |
| 71 |
intensity. Right click on the plot and select mean intensity for the left |
| 72 |
axis y data. Then try the intensity at *q=0.02* and in the *q* range 0.01-0.03. |
| 73 |
|
| 74 |
* *Note:* You need to have the drag button in the plot control bar unselected to |
| 75 |
get a right click menu. |
| 76 |
|
| 77 |
* *Tip:* CHROMIXS, in the ATSAS software displays the average intensity |
| 78 |
over the *q* range 0.01-0.08 :math:`Å^{-1}`. To achieve a similar |
| 79 |
display in RAW, set your q range for the intensity to that. Note that |
| 80 |
RAW will display the sum of the intensity over the range while CHROMIXS |
| 81 |
displays mean intensity for the range, so the results won't be exactly the same. |
| 82 |
|
| 83 |
#. Return to plotting the integrated intensity. Zoom in near the base of the peak. Notice |
| 84 |
that there are two smaller peaks on the left, likely corresponding to higher order |
| 85 |
oligomers that we don’t have the signal to properly resolve. Also notice that the |
| 86 |
baseline after the peak is not the same as the baseline before the peak. This can happen |
| 87 |
for several reasons, such as damaged protein sticking to the sample cell windows. |
| 88 |
|
| 89 |
* *Tip:* Click on the magnifying glass at the bottom of the plot, then click |
| 90 |
and drag on the plot to select a region to zoom in on. |
| 91 |
|
| 92 |
|series_plot3_png| |
| 93 |
|
| 94 |
#. Zoom back out to the full plot. |
| 95 |
|
| 96 |
* *Tip:* Click the Home (house) button at the bottom of the plot. |
| 97 |
|
| 98 |
#. In order to determine if we really have a single species across the peak, we will |
| 99 |
calculate the |Rg| and MW as a function of frame number. Click on the "LC |
| 100 |
Analysis" button at the bottom of the Series control panel or right click on the |
| 101 |
filename in the Series control panel and select "LC Series analysis" to open the |
| 102 |
LC Series analysis panel. |
| 103 |
|
| 104 |
* *Note:* At the top of the control panel in this window, in the 'Series info' |
| 105 |
section you'll see several settings. If you had RNA instead of protein, |
| 106 |
you would use the Vc Mol. type menu to select that option. This affects |
| 107 |
the calculation of the molecular weight. You could also change the Vp |
| 108 |
density away from the default value, or change the averaging window |
| 109 |
(discussed below). |
| 110 |
|
| 111 |
|lc_analysis_main_png| |
| 112 |
|
| 113 |
#. The LC Series analysis panel provides basic and advanced analysis tools for |
| 114 |
liquid chromatography experiments. Here we will show how to select buffer |
| 115 |
and sample regions, and send final processed data to the Profiles plot. The |
| 116 |
advanced baseline correction features are discussed later. |
| 117 |
|
| 118 |
In order to calculate |Rg| and other parameters as a function of elution time |
| 119 |
(Frame #), we need to define a buffer region. RAW can do this automatically. |
| 120 |
In the 'Buffer' section click the 'Auto' button. |
| 121 |
|
| 122 |
|lc_analysis_buffer_auto_png| |
| 123 |
|
| 124 |
* *Checkpoint:* You should see a buffer range show up in the buffer list, |
| 125 |
with defined start and end values. The region will be shown in green on |
| 126 |
the Unsubtracted plot. |
| 127 |
|
| 128 |
|lc_analysis_buffer_range_png| |
| 129 |
|
| 130 |
#. You can make fine manual adjustments to the buffer range if necessary. Zoom |
| 131 |
in on the baseline around the buffer region. Use the up/down arrows for the |
| 132 |
Start and End points to adjust the buffer region a little bit. You will see |
| 133 |
the region on the plot update as you make the changes. |
| 134 |
|
| 135 |
|lc_analysis_buffer_adjust_png| |
| 136 |
|
| 137 |
* *Warning:* The automatic buffer determination can be wrong! Always be sure |
| 138 |
to manually inspect the region it picked. In particular, large flat leading edge |
| 139 |
shoulders next to the main peak can look like a baseline region to the |
| 140 |
algorithm, and will often mistakenly be picked. |
| 141 |
|
| 142 |
* *Tip:* If the SAXS data isn't clear (noisy, low signal, etc.), it can be |
| 143 |
useful to inspect the UV trace associated with the SEC elution to see |
| 144 |
where there are minor elution components that you should exclude from |
| 145 |
your buffer selection. |
| 146 |
|
| 147 |
#. Zoom back out on the plot. Reset the buffer range to 504 to 562 by typing |
| 148 |
those values in the Start/End range boxes and hitting enter. |
| 149 |
|
| 150 |
#. To set the buffer region, create a set of subtracted profiles, and calculate |
| 151 |
structural parameters as a function of elution time, click the 'Set buffer' |
| 152 |
button. This may take a while to calculate. |
| 153 |
|
| 154 |
|lc_analysis_buffer_set_png| |
| 155 |
|
| 156 |
* *Note:* All of the files in the given buffer range will be averaged and used as a buffer. |
| 157 |
A sliding average window (size defined by the 'Averaging window size' in the |
| 158 |
'Series Info' section) is then moved across the SEC curve. So for a |
| 159 |
window of size five, the profiles corresponding to frames 0-4, 1-5, 2-6, |
| 160 |
etc will be averaged. From each of these averaged set of curves, the average |
| 161 |
buffer will be subtracted, and RAW will attempt to calculate the |Rg|, |
| 162 |
MW, and I(0). These values are then plotted as a function of frame number. |
| 163 |
|
| 164 |
* *Warning:* It is important that the buffer range actually be buffer! In this case, |
| 165 |
we need to make sure to not include the small peaks before the main peak. |
| 166 |
|
| 167 |
#. Once the calculation is finished, the window should automatically display the |
| 168 |
Subtracted plot. If it doesn't, click on the 'Subtracted' tab in the plot. |
| 169 |
On this plot there is a new Intensity vs. Frame # curve, representing the |
| 170 |
subtracted data. There is also a set of markers, showing one of the calculated |
| 171 |
parameters. By default the |Rg| displayed. The calculated parameters are |
| 172 |
plotted on the right Y axis. You can show |Rg|, I(0), and MW calculated by |
| 173 |
the volume of correlation (Vc) and adjusted Porod volume (Vp) methods. Click |
| 174 |
on the 'Calculated value' menu to switch between the different displays. |
| 175 |
|
| 176 |
* *Try:* Show the |Rg|, MW (Vc), and MW (Vp). Notice that the MW estimate |
| 177 |
varies between the two different methods. |
| 178 |
|
| 179 |
* *Note:* You’ll notice a region of roughly constant |Rg| across the peak. To |
| 180 |
either side there are regions with higher or lower |Rg| values. Some of these |
| 181 |
variations, particularly on the right side, are from scattering profiles |
| 182 |
near the edge of the peak with lower concentrations of sample, leading |
| 183 |
to more noise in determining the |Rg| values. There may also be some |
| 184 |
effects from the small peaks on the leading (left) side of the peak, |
| 185 |
and from the baseline mismatch between left and right sides of the peak. |
| 186 |
|
| 187 |
|lc_analysis_subtracted_png| |
| 188 |
|
| 189 |
#. A monodisperse peak should display a region of flat |Rg| and MW near the center. |
| 190 |
Note that some spread on either edge can come from small shoulders of other |
| 191 |
components, bad buffer selection, or just the low signal to noise in the tails |
| 192 |
of the peak. Zoom in on the |Rg| and MW values across the peak to verify that |
| 193 |
these show a significant flat region. |
| 194 |
|
| 195 |
RAW can automatically determine a good sample region (good being defined |
| 196 |
as monodisperse and excluding low signal to noise data). To do this, click |
| 197 |
the 'Auto' button in the Sample region. |
| 198 |
|
| 199 |
|lc_analysis_sample_auto_png| |
| 200 |
|
| 201 |
* *Checkpoint:* You should see a sample range show up in the sample list, |
| 202 |
with defined start and end values. The region will be shown in green on |
| 203 |
the Subtracted plot. |
| 204 |
|
| 205 |
|lc_analysis_sample_region_png| |
| 206 |
|
| 207 |
#. In the plot, zoom in on the peak region and verify that the |Rg| and MW seem |
| 208 |
flat in the selected sample range. |
| 209 |
|
| 210 |
|lc_analysis_sample_region_plot_png| |
| 211 |
|
| 212 |
* *Tip:* You can manually adjust the sample region range in the same way |
| 213 |
as the buffer range, using the controls in the Start/End boxes. |
| 214 |
|
| 215 |
#. Once you are satisfied with the region picked (should be 699-713), click the |
| 216 |
'To Profiles Plot' button. This averages the selected region and sends the resulting |
| 217 |
average to RAW's Profiles Plot. |
| 218 |
|
| 219 |
* *Note:* RAW first averages the selected sample and buffer regions in the |
| 220 |
unsubtracted data, then subtracts. This avoids the possibility of correlated |
| 221 |
noise that would arise from averaging the subtracted files. |
| 222 |
|
| 223 |
|lc_analysis_sample_to_main_plot_png| |
| 224 |
|
| 225 |
#. If you adjust the sample or buffer region in a way that could be problematic, |
| 226 |
RAW will warn you. Try this. |
| 227 |
|
| 228 |
* Adjust the Buffer start to include more of the elution range, such as |
| 229 |
starting at 450. You will want to click on the 'Unsubtracted' plot to |
| 230 |
see the buffer range. Then click 'Set Buffer'. You will see a warning window |
| 231 |
telling you what might be wrong with the selected region. Click 'Cancel'. |
| 232 |
|
| 233 |
|lc_analysis_buffer_range_warning_png| |
| 234 |
|
| 235 |
* Adjust the Sample start to include some of the non-flat Rg region, such as |
| 236 |
starting at 680. Then click 'To Profiles Plot'. You will see a warning window |
| 237 |
telling you what might be wrong with the selected region. Click 'Cancel'. |
| 238 |
|
| 239 |
|lc_analysis_sample_range_warning_png| |
| 240 |
|
| 241 |
* *Note:* For buffer regions, RAW checks frame-wise similarity across the |
| 242 |
whole *q* range and at low and high *q*, correlations in intensity, and |
| 243 |
whether there are multiple singular values in the selected region. |
| 244 |
|
| 245 |
For sample regions, RAW checks frame-wise similarity across the |
| 246 |
whole *q* range and at low and high *q*, correlations in calculated Rg |
| 247 |
and MW values, whether there are multiple singular values in the selected |
| 248 |
region, and if some of the selected frames decrease the signal to noise |
| 249 |
of the average. |
| 250 |
|
| 251 |
#. Click 'OK' to close the window and save your analysis results. In the Info panel |
| 252 |
above the Series control panel you should see information about the series, |
| 253 |
including the selected buffer and sample ranges. If you reopen |
| 254 |
the LC analysis window you will see the buffer and sample regions you selected |
| 255 |
are remembered. |
| 256 |
|
| 257 |
#. Click on the Profiles plot tab and the Profiles tab. You should see one scattering |
| 258 |
profile, the buffer subtracted data set you sent to the Profiles plot. Carry out |
| 259 |
Guinier and MW analysis. |
| 260 |
|
| 261 |
* *Note:* The I(0) reference and absolute calibration will not be accurate for |
| 262 |
SEC-SAXS data, as the concentration is not accurately known. |
| 263 |
|
| 264 |
* *Question:* How does the |Rg| and MW you get from the averaged curve compare |
| 265 |
to what RAW found automatically for the peak? |
| 266 |
|
| 267 |
* *Tip:* Make sure your plot axes are Log-Lin or Log-Log. Make sure that both |
| 268 |
plots are shown by clicking the 1/2 button at the bottom of the plot window. |
| 269 |
|
| 270 |
#. This particular dataset shows a small difference between initial and final buffer |
| 271 |
scattering profiles. A better scattering profile might be obtained by using buffer |
| 272 |
from both sides of the peak. To do so, start by reopening the LC Series Analysis panel. |
| 273 |
|
| 274 |
#. Switch to showing the unsubtracted intensity by clicking on the 'Unsubtracted' plot tab. |
| 275 |
|
| 276 |
#. Add a second buffer region by clicking the 'Add region' button. |
| 277 |
|
| 278 |
#. For the second region, click the 'Pick' button. |
| 279 |
|
| 280 |
|lc_analysis_buffer_pick_png| |
| 281 |
|
| 282 |
#. Move your mouse across the plot. You will see a vertical green line moving |
| 283 |
with the mouse cursor. This represents the start of the buffer region. Click |
| 284 |
once to fix the start point where you click. Move the mouse further to the |
| 285 |
right and click again to fix the end point of the buffer region. |
| 286 |
|
| 287 |
|lc_analysis_two_buffers_png| |
| 288 |
|
| 289 |
#. Once you are happy with the second buffer region, click 'Set buffer'. A range like |
| 290 |
~840-896 is reasonable. |
| 291 |
|
| 292 |
#. A warning window will pop up. In this case, we have purposefully chosen two |
| 293 |
buffer regions because they are different, so ignore the warning and click |
| 294 |
'Continue'. |
| 295 |
|
| 296 |
#. Remove the old sample region by clicking in the empty space to the right of |
| 297 |
the 'Pick' button to highlight it, and then clicking the 'Remove region' button. |
| 298 |
|
| 299 |
|lc_analysis_remove_sample_png| |
| 300 |
|
| 301 |
#. Click the 'Auto' button to automatically find a new sample region. Click the |
| 302 |
'To Profiles Plot' button to send that new region to the Profiles plot. |
| 303 |
|
| 304 |
* *Try:* You can see what the data subtracted by just the second buffer |
| 305 |
region looks like by removing the first buffer region, setting the buffer |
| 306 |
again, finding a new good sample region, and sending new region to the |
| 307 |
Profiles plot. |
| 308 |
|
| 309 |
#. Cancel out of the LC Series analysis window. This will not save the changes |
| 310 |
you made to the buffer and sample regions. |
| 311 |
|
| 312 |
#. Carry out the |Rg| and MW analysis on the new curve. How does the scattering |
| 313 |
profile compare to the one that you generated using only buffer from before |
| 314 |
the peak? |
| 315 |
|
| 316 |
* *Tip:* You should see subtle but noticeable differences in the Guinier |
| 317 |
fit. |
| 318 |
|
| 319 |
* *Note:* An alternative approach to using several buffer regions is to use |
| 320 |
a single buffer region and apply a baseline correction. Both approaches |
| 321 |
have advantages and disadvantages. If you want to do EFA deconvolution, |
| 322 |
it is best to not use a baseline correction, however in other cases |
| 323 |
it will be more accurate as it doesn't assume a single average buffer |
| 324 |
across the peak. |
| 325 |
|
| 326 |
#. Return to the Series control and plot panels. |
| 327 |
|
| 328 |
#. If you want to look at either individual profiles or the average of a |
| 329 |
range of profiles you can send profiles to the Profiles plot. To select which |
| 330 |
series curve to send profiles from, star the series curve of interest. |
| 331 |
|
| 332 |
|series_star_png| |
| 333 |
|
| 334 |
#. In the ‘Data to Profiles plot’ section enter the frame range of interest. |
| 335 |
For this dataset, try the buffer range you selected: 504 to 562. Then click |
| 336 |
the ‘Average’ button. That will send the average buffer to the Profiles plot. |
| 337 |
|
| 338 |
* *Try:* Send the average of the sample range you selected to the main |
| 339 |
plot (699 to 713), carry out the subtraction, and verify it’s the same as |
| 340 |
the curve produced by the ‘To Profiles Plot’ button in the LC Series Analysis |
| 341 |
panel. |
| 342 |
|
| 343 |
* *Question:* When you send the sample average to the Profiles plot you will |
| 344 |
get a warning that the profiles are different. Why? |
| 345 |
|
| 346 |
|series_average_main_plot_png| |
| 347 |
|
| 348 |
#. You can also send subtracted (or baseline corrected data) to the Profiles plot. |
| 349 |
For the selected sample range, select the ‘Subtracted’ frames and send each |
| 350 |
individual profile to the plot using the ‘Plot’ button. |
| 351 |
|
| 352 |
* *Try:* Average these profiles and verify they match the subtracted |
| 353 |
profiles for this data set generated previously. |
| 354 |
|
| 355 |
|series_profile_main_plot_png| |
| 356 |
|
| 357 |
#. Click on the colored line next |
| 358 |
to the star in the Series control panel. In the line properties control panel |
| 359 |
this brings up, change the Calc Marker color to something different. Add a |
| 360 |
line to the Calc Markers by selecting line style ‘-’ (solid), and adjust |
| 361 |
the line color to your liking. |
| 362 |
|
| 363 |
* *Tip:* You can do the same thing to adjust the colors of the scattering |
| 364 |
profiles and IFTs in the Profiles and IFT control tabs. |
| 365 |
|
| 366 |
|series_color_png| |
| 367 |
|
| 368 |
|series_line_props_png| |
| 369 |
|
| 370 |
#. For certain beamlines (the BioCAT beamline at the APS and the MacCHESS |
| 371 |
BioSAXS beamline at CHESS), RAW can automatically load in series data |
| 372 |
from the series panel. This is typically used for online analysis while |
| 373 |
data is being collected, but can be used to load in series you have |
| 374 |
already collected as well. |
| 375 |
|
| 376 |
#. We will load in the Bovine Serum Albumin (BSA) SEC-SAXS data contained |
| 377 |
in the **sec_sample_2** data folder using this automatic method. |
| 378 |
In the Series control panel, click the “Select” button. Navigate to |
| 379 |
the **Tutorial_Data/series_data/sec_sample_2** folder and select any of |
| 380 |
the **.dat** files in the folder. |
| 381 |
|
| 382 |
* *Troubleshooting:* If you get an error message, it means you don't have |
| 383 |
a configuration file loaded. Load the SAXS.cfg file referenced :ref:`earlier <s1p1>`. |
| 384 |
|
| 385 |
* The configuration file must be set to either BioCAT or MacCHESS beamlines |
| 386 |
for this method to work. Otherwise, RAW doesn't know how to create |
| 387 |
all the filenames in a series from a single filename. |
| 388 |
|
| 389 |
|series_panel_png| |
| 390 |
|
| 391 |
#. The SEC-SAXS run will automatically load. Note that because SAXS data can be |
| 392 |
reported with an arbitrary intensity scale, the total intensity of this |
| 393 |
series is much larger than the previous series. |
| 394 |
|
| 395 |
#. Right click on the **profile_001** series and select "Adjust scale, offset, q range". |
| 396 |
This will open a window that allows you to adjust the overall scale and offset |
| 397 |
for your series data, as well as the q range used for each type of profile |
| 398 |
in the series data. Set the scale to 1800 and click "OK". You should see |
| 399 |
that this scales the profiles_001 series to match the BSA series. |
| 400 |
|
| 401 |
* *Tip:* This applies the scale, offset, and q range settings to every profile |
| 402 |
in the series. So if you were now to send a profile to the Profiles plot, |
| 403 |
it would have an overall scale factor of 1800 applied to it. |
| 404 |
|
| 405 |
|series_scale_png| |
| 406 |
|
| 407 |
#. Hide the first series (**profile_001**). |
| 408 |
|
| 409 |
#. Select a good buffer region, and calculate the |Rg| and MW across the peak for the BSA. |
| 410 |
|
| 411 |
* *Tip:* If you hover your mouse cursor over the info icon, you will see the buffer |
| 412 |
range and window size used to calculate the parameters. |
| 413 |
|
| 414 |
* *Question:* Is the BSA peak one species? |
| 415 |
|
| 416 |
#. Find the useful region of the peak (constant |Rg|/MW), and send the buffer and sample |
| 417 |
data to the Profiles plot. Carry out the standard |Rg| and MW analysis on the subtracted |
| 418 |
scattering profile. For BSA, we expect |Rg| ~28 Å and MW ~66 kDa. |
| 419 |
|
| 420 |
#. In the Series control tab, right click on the name of BSA curve in the list. Select export |
| 421 |
data and save it in an appropriate location. This will save a CSV file with the frame |
| 422 |
number, integrated intensity, radius of gyration, molecular weight, filename for each |
| 423 |
frame number, and a few other items. This allows you to plot that data for publications, |
| 424 |
align it with the UV trace, or whatever else you want to do with it. |
| 425 |
|
| 426 |
* *Try:* Open the **.csv** file you just saved in Excel or Libre/Open Office Calc. |
| 427 |
|
| 428 |
#. Select both items in the Series control panel list, and save them in the **series_data** |
| 429 |
folder. This saves the series data in a form that can be quickly loaded by RAW. |
| 430 |
|
| 431 |
* *Try:* Clear the Series data and then open one of your saved files from the Files tab |
| 432 |
using either the “Plot” or “Plot Series” button. |
| 433 |
|
| 434 |
#. Select just the **profile_001** item, right click and select "Save report". Check |
| 435 |
the profiles associated with the SEC-SAXS series, so that you're saving a |
| 436 |
report that includes both the series and the averaged subtracted profile. |
| 437 |
Save the report as a pdf. |
| 438 |
|
| 439 |
|series_report_png| |
| 440 |
|
| 441 |
.. |series_load1_png| image:: images/series_load1.png |
| 442 |
:width: 500 px |
| 443 |
:target: ../_images/series_load1.png |
| 444 |
|
| 445 |
.. |series_panel_png| image:: images/series_panel.png |
| 446 |
:width: 400 px |
| 447 |
:target: ../_images/series_panel.png |
| 448 |
|
| 449 |
.. |series_plot_png| image:: images/series_plot.png |
| 450 |
:target: ../_images/series_plot.png |
| 451 |
|
| 452 |
.. |series_plot2_png| image:: images/series_plot2.png |
| 453 |
:target: ../_images/series_plot2.png |
| 454 |
|
| 455 |
.. |series_plot3_png| image:: images/series_plot3.png |
| 456 |
:target: ../_images/series_plot2.png |
| 457 |
|
| 458 |
.. |lc_analysis_main_png| image:: images/lc_analysis_main.png |
| 459 |
:target: ../_images/series_analysis_main.png |
| 460 |
|
| 461 |
.. |lc_analysis_buffer_auto_png| image:: images/lc_analysis_buffer_auto.png |
| 462 |
:width: 300 px |
| 463 |
:target: ../_images/series_panel.png |
| 464 |
|
| 465 |
.. |lc_analysis_buffer_range_png| image:: images/lc_analysis_buffer_range.png |
| 466 |
:target: ../_images/lc_analysis_buffer_range.png |
| 467 |
|
| 468 |
.. |lc_analysis_buffer_adjust_png| image:: images/lc_analysis_buffer_adjust.png |
| 469 |
:width: 300 px |
| 470 |
:target: ../_images/lc_analysis_buffer_adjust.png |
| 471 |
|
| 472 |
.. |lc_analysis_buffer_set_png| image:: images/lc_analysis_buffer_set.png |
| 473 |
:width: 300 px |
| 474 |
:target: ../_images/lc_analysis_buffer_set.png |
| 475 |
|
| 476 |
.. |lc_analysis_subtracted_png| image:: images/lc_analysis_subtracted.png |
| 477 |
:target: ../_images/lc_analysis_subtracted.png |
| 478 |
|
| 479 |
.. |lc_analysis_sample_auto_png| image:: images/lc_analysis_sample_auto.png |
| 480 |
:width: 300 px |
| 481 |
:target: ../_images/lc_analysis_sample_auto.png |
| 482 |
|
| 483 |
.. |lc_analysis_sample_region_png| image:: images/lc_analysis_sample_region.png |
| 484 |
:target: ../_images/lc_analysis_sample_region.png |
| 485 |
|
| 486 |
.. |lc_analysis_sample_region_plot_png| image:: images/lc_analysis_sample_region_plot.png |
| 487 |
:target: ../_images/lc_analysis_sample_region_plot.png |
| 488 |
|
| 489 |
.. |lc_analysis_sample_to_main_plot_png| image:: images/lc_analysis_sample_to_main_plot.png |
| 490 |
:width: 300 px |
| 491 |
:target: ../_images/lc_analysis_sample_to_main_plot.png |
| 492 |
|
| 493 |
.. |lc_analysis_buffer_range_warning_png| image:: images/lc_analysis_buffer_range_warning.png |
| 494 |
:width: 500 px |
| 495 |
:target: ../_images/lc_analysis_buffer_range_warning.png |
| 496 |
|
| 497 |
.. |lc_analysis_sample_range_warning_png| image:: images/lc_analysis_sample_range_warning.png |
| 498 |
:width: 500 px |
| 499 |
:target: ../_images/lc_analysis_sample_range_warning.png |
| 500 |
|
| 501 |
.. |lc_analysis_buffer_pick_png| image:: images/lc_analysis_buffer_pick.png |
| 502 |
:width: 300 px |
| 503 |
:target: ../_images/lc_analysis_buffer_pick.png |
| 504 |
|
| 505 |
.. |lc_analysis_two_buffers_png| image:: images/lc_analysis_two_buffers.png |
| 506 |
:target: ../_images/lc_analysis_two_buffers.png |
| 507 |
|
| 508 |
.. |lc_analysis_remove_sample_png| image:: images/lc_analysis_remove_sample.png |
| 509 |
:width: 300 px |
| 510 |
:target: ../_images/lc_analysis_remove_sample.png |
| 511 |
|
| 512 |
.. |series_star_png| image:: images/series_star.png |
| 513 |
:width: 400 px |
| 514 |
:target: ../_images/series_star.png |
| 515 |
|
| 516 |
.. |series_average_main_plot_png| image:: images/series_average_main_plot.png |
| 517 |
:width: 400 px |
| 518 |
:target: ../_images/series_average_main_plot.png |
| 519 |
|
| 520 |
.. |series_profile_main_plot_png| image:: images/series_profile_main_plot.png |
| 521 |
:width: 400 px |
| 522 |
:target: ../_images/series_profile_main_plot.png |
| 523 |
|
| 524 |
.. |series_color_png| image:: images/series_color.png |
| 525 |
:width: 400 px |
| 526 |
:target: ../_images/series_color.png |
| 527 |
|
| 528 |
.. |series_line_props_png| image:: images/series_line_props.png |
| 529 |
:width: 400 px |
| 530 |
:target: ../_images/series_line_props.png |
| 531 |
|
| 532 |
.. |series_scale_png| image:: images/series_scale.png |
| 533 |
:width: 300 px |
| 534 |
:target: ../_images/series_scale.png |
| 535 |
|
| 536 |
.. |series_report_png| image:: images/series_report.png |
| 537 |
:width: 450 px |
| 538 |
:target: ../_images/series_report.png |
| 539 |
|
| 540 |
|
| 541 |
.. |Rg| replace:: R\ :sub:`g` |