| 1 |
# SPDX-License-Identifier: GPL-2.0-only |
| 2 |
menuconfig POWER_RESET |
| 3 |
bool "Board level reset or power off" |
| 4 |
help |
| 5 |
Provides a number of drivers which either reset a complete board |
| 6 |
or shut it down, by manipulating the main power supply on the board. |
| 7 |
|
| 8 |
Say Y here to enable board reset and power off |
| 9 |
|
| 10 |
if POWER_RESET |
| 11 |
|
| 12 |
config POWER_RESET_AS3722 |
| 13 |
bool "ams AS3722 power-off driver" |
| 14 |
depends on MFD_AS3722 |
| 15 |
help |
| 16 |
This driver supports turning off board via a ams AS3722 power-off. |
| 17 |
|
| 18 |
config POWER_RESET_AT91_POWEROFF |
| 19 |
tristate "Atmel AT91 poweroff driver" |
| 20 |
depends on ARCH_AT91 |
| 21 |
default SOC_AT91SAM9 || SOC_SAMA5 |
| 22 |
help |
| 23 |
This driver supports poweroff for Atmel AT91SAM9 and SAMA5 |
| 24 |
SoCs |
| 25 |
|
| 26 |
config POWER_RESET_AT91_RESET |
| 27 |
tristate "Atmel AT91 reset driver" |
| 28 |
depends on ARCH_AT91 |
| 29 |
default SOC_AT91SAM9 || SOC_SAM9X60 || SOC_SAM9X7 || SOC_SAMA5 |
| 30 |
help |
| 31 |
This driver supports restart for Atmel AT91SAM9 and SAMA5 |
| 32 |
SoCs |
| 33 |
|
| 34 |
config POWER_RESET_AT91_SAMA5D2_SHDWC |
| 35 |
tristate "Atmel AT91 SAMA5D2-Compatible shutdown controller driver" |
| 36 |
depends on ARCH_AT91 |
| 37 |
default SOC_SAM9X60 || SOC_SAM9X7 || SOC_SAMA5 |
| 38 |
help |
| 39 |
This driver supports the alternate shutdown controller for some Atmel |
| 40 |
SAMA5 SoCs. It is present for example on SAMA5D2 SoC. |
| 41 |
|
| 42 |
config POWER_RESET_ATC260X |
| 43 |
tristate "Actions Semi ATC260x PMIC power-off driver" |
| 44 |
depends on MFD_ATC260X |
| 45 |
help |
| 46 |
This driver provides power-off and restart support for a system |
| 47 |
through Actions Semi ATC260x series PMICs. |
| 48 |
|
| 49 |
config POWER_RESET_AXXIA |
| 50 |
bool "LSI Axxia reset driver" |
| 51 |
depends on ARCH_AXXIA |
| 52 |
help |
| 53 |
This driver supports restart for Axxia SoC. |
| 54 |
|
| 55 |
Say Y if you have an Axxia family SoC. |
| 56 |
|
| 57 |
config POWER_RESET_BRCMKONA |
| 58 |
bool "Broadcom Kona reset driver" |
| 59 |
depends on ARM || COMPILE_TEST |
| 60 |
default ARCH_BCM_MOBILE |
| 61 |
help |
| 62 |
This driver provides restart support for Broadcom Kona chips. |
| 63 |
|
| 64 |
Say Y here if you have a Broadcom Kona-based board and you wish |
| 65 |
to have restart support. |
| 66 |
|
| 67 |
config POWER_RESET_BRCMSTB |
| 68 |
bool "Broadcom STB reset driver" |
| 69 |
depends on ARCH_BRCMSTB || BMIPS_GENERIC || COMPILE_TEST |
| 70 |
depends on MFD_SYSCON |
| 71 |
default ARCH_BRCMSTB || BMIPS_GENERIC |
| 72 |
help |
| 73 |
This driver provides restart support for Broadcom STB boards. |
| 74 |
|
| 75 |
Say Y here if you have a Broadcom STB board and you wish |
| 76 |
to have restart support. |
| 77 |
|
| 78 |
config POWER_RESET_EP93XX |
| 79 |
bool "Cirrus EP93XX reset driver" if COMPILE_TEST |
| 80 |
depends on MFD_SYSCON |
| 81 |
default ARCH_EP93XX |
| 82 |
select AUXILIARY_BUS |
| 83 |
help |
| 84 |
This driver provides restart support for Cirrus EP93XX SoC. |
| 85 |
|
| 86 |
Say Y here if you have a Cirrus EP93XX SoC and you wish |
| 87 |
to have restart support. |
| 88 |
|
| 89 |
config POWER_RESET_GEMINI_POWEROFF |
| 90 |
bool "Cortina Gemini power-off driver" |
| 91 |
depends on ARCH_GEMINI || COMPILE_TEST |
| 92 |
depends on OF && HAS_IOMEM |
| 93 |
default ARCH_GEMINI |
| 94 |
help |
| 95 |
This driver supports turning off the Cortina Gemini SoC. |
| 96 |
Select this if you're building a kernel with Gemini SoC support. |
| 97 |
|
| 98 |
config POWER_RESET_GPIO |
| 99 |
bool "GPIO power-off driver" |
| 100 |
depends on OF_GPIO |
| 101 |
help |
| 102 |
This driver supports turning off your board via a GPIO line. |
| 103 |
If your board needs a GPIO high/low to power down, say Y and |
| 104 |
create a binding in your devicetree. |
| 105 |
|
| 106 |
config POWER_RESET_GPIO_RESTART |
| 107 |
bool "GPIO restart driver" |
| 108 |
depends on OF_GPIO |
| 109 |
help |
| 110 |
This driver supports restarting your board via a GPIO line. |
| 111 |
If your board needs a GPIO high/low to restart, say Y and |
| 112 |
create a binding in your devicetree. |
| 113 |
|
| 114 |
config POWER_RESET_HISI |
| 115 |
bool "Hisilicon power-off driver" |
| 116 |
depends on ARCH_HISI |
| 117 |
help |
| 118 |
Reboot support for Hisilicon boards. |
| 119 |
|
| 120 |
config POWER_RESET_LINKSTATION |
| 121 |
tristate "Buffalo LinkStation power-off driver" |
| 122 |
depends on ARCH_MVEBU || COMPILE_TEST |
| 123 |
depends on OF_MDIO && PHYLIB |
| 124 |
help |
| 125 |
This driver supports turning off some Buffalo LinkStations by |
| 126 |
setting an output pin at the ethernet PHY to the correct state. |
| 127 |
It also makes the device compatible with the WoL function. |
| 128 |
|
| 129 |
Say Y here if you have a Buffalo LinkStation LS421D/E. |
| 130 |
|
| 131 |
config POWER_RESET_MACSMC |
| 132 |
tristate "Apple SMC reset/power-off driver" |
| 133 |
depends on MFD_MACSMC |
| 134 |
help |
| 135 |
This driver supports reset and power-off on Apple Mac machines |
| 136 |
that implement this functionality via the SMC. |
| 137 |
|
| 138 |
Say Y here if you have an Apple Silicon Mac. |
| 139 |
|
| 140 |
config POWER_RESET_MSM |
| 141 |
bool "Qualcomm MSM power-off driver" |
| 142 |
depends on ARCH_QCOM |
| 143 |
help |
| 144 |
Power off and restart support for Qualcomm boards. |
| 145 |
|
| 146 |
config POWER_RESET_QCOM_PON |
| 147 |
tristate "Qualcomm power-on driver" |
| 148 |
depends on ARCH_QCOM |
| 149 |
depends on MFD_SPMI_PMIC |
| 150 |
select REBOOT_MODE |
| 151 |
help |
| 152 |
Power On support for Qualcomm boards. |
| 153 |
If you have a Qualcomm platform and need support for |
| 154 |
power-on and reboot reason, Say Y. |
| 155 |
If unsure, Say N. |
| 156 |
|
| 157 |
config POWER_RESET_OCELOT_RESET |
| 158 |
bool "Microsemi Ocelot reset driver" |
| 159 |
depends on MSCC_OCELOT || ARCH_SPARX5 || COMPILE_TEST |
| 160 |
select MFD_SYSCON |
| 161 |
help |
| 162 |
This driver supports restart for Microsemi Ocelot SoC and similar. |
| 163 |
|
| 164 |
config POWER_RESET_ODROID_GO_ULTRA_POWEROFF |
| 165 |
bool "Odroid Go Ultra power-off driver" |
| 166 |
depends on ARCH_MESON || COMPILE_TEST |
| 167 |
depends on I2C=y && OF |
| 168 |
help |
| 169 |
This driver supports Power off for Odroid Go Ultra device. |
| 170 |
|
| 171 |
config POWER_RESET_PIIX4_POWEROFF |
| 172 |
tristate "Intel PIIX4 power-off driver" |
| 173 |
depends on PCI |
| 174 |
depends on HAS_IOPORT |
| 175 |
depends on MIPS || COMPILE_TEST |
| 176 |
help |
| 177 |
This driver supports powering off a system using the Intel PIIX4 |
| 178 |
southbridge, for example the MIPS Malta development board. The |
| 179 |
southbridge SOff state is entered in response to a request to |
| 180 |
power off the system. |
| 181 |
|
| 182 |
config POWER_RESET_LTC2952 |
| 183 |
bool "LTC2952 PowerPath power-off driver" |
| 184 |
depends on OF_GPIO |
| 185 |
help |
| 186 |
This driver supports an external powerdown trigger and board power |
| 187 |
down via the LTC2952. Bindings are made in the device tree. |
| 188 |
|
| 189 |
config POWER_RESET_MT6323 |
| 190 |
bool "MediaTek MT6323 power-off driver" |
| 191 |
depends on MFD_MT6397 |
| 192 |
help |
| 193 |
The power-off driver is responsible for externally shutdown down |
| 194 |
the power of a remote MediaTek SoC MT6323 is connected to through |
| 195 |
controlling a tiny circuit BBPU inside MT6323 RTC. |
| 196 |
|
| 197 |
Say Y if you have a board where MT6323 could be found. |
| 198 |
|
| 199 |
config POWER_RESET_QNAP |
| 200 |
bool "QNAP power-off driver" |
| 201 |
depends on OF_GPIO && PLAT_ORION |
| 202 |
help |
| 203 |
This driver supports turning off QNAP NAS devices by sending |
| 204 |
commands to the microcontroller which controls the main power. |
| 205 |
|
| 206 |
Say Y if you have a QNAP NAS. |
| 207 |
|
| 208 |
config POWER_RESET_REGULATOR |
| 209 |
bool "Regulator subsystem power-off driver" |
| 210 |
depends on OF && REGULATOR |
| 211 |
help |
| 212 |
This driver supports turning off your board by disabling a |
| 213 |
power regulator defined in the devicetree. |
| 214 |
|
| 215 |
config POWER_RESET_RESTART |
| 216 |
bool "Restart power-off driver" |
| 217 |
help |
| 218 |
Some boards don't actually have the ability to power off. |
| 219 |
Instead they restart, and u-boot holds the SoC until the |
| 220 |
user presses a key. u-boot then boots into Linux. |
| 221 |
|
| 222 |
config POWER_RESET_ST |
| 223 |
bool "ST restart driver" |
| 224 |
depends on ARCH_STI |
| 225 |
help |
| 226 |
Reset support for STMicroelectronics boards. |
| 227 |
|
| 228 |
config POWER_RESET_TH1520_AON |
| 229 |
tristate "T-Head TH1520 AON firmware poweroff and reset driver" |
| 230 |
depends on TH1520_PM_DOMAINS |
| 231 |
help |
| 232 |
This driver supports power-off and reset operations for T-Head |
| 233 |
TH1520 SoCs running the AON firmware. |
| 234 |
|
| 235 |
config POWER_RESET_TORADEX_EC |
| 236 |
tristate "Toradex Embedded Controller power-off and reset driver" |
| 237 |
depends on ARCH_MXC || COMPILE_TEST |
| 238 |
depends on I2C |
| 239 |
select REGMAP_I2C |
| 240 |
help |
| 241 |
This driver supports power-off and reset for SMARC Toradex SoMs, |
| 242 |
for example the SMARC iMX8MP and SMARC iMX95, using Toradex |
| 243 |
Embedded Controller (EC). |
| 244 |
|
| 245 |
Say Y here if you have a Toradex SMARC SoM. |
| 246 |
|
| 247 |
If unsure, say N. |
| 248 |
|
| 249 |
config POWER_RESET_TPS65086 |
| 250 |
bool "TPS65086 restart driver" |
| 251 |
depends on MFD_TPS65086 |
| 252 |
help |
| 253 |
This driver adds support for resetting the TPS65086 PMIC on restart. |
| 254 |
|
| 255 |
config POWER_RESET_VERSATILE |
| 256 |
bool "ARM Versatile family reboot driver" |
| 257 |
depends on ARM |
| 258 |
depends on MFD_SYSCON |
| 259 |
depends on OF |
| 260 |
help |
| 261 |
Power off and restart support for ARM Versatile family of |
| 262 |
reference boards. |
| 263 |
|
| 264 |
config POWER_RESET_VEXPRESS |
| 265 |
bool "ARM Versatile Express power-off and reset driver" |
| 266 |
depends on ARM || ARM64 |
| 267 |
depends on VEXPRESS_CONFIG=y |
| 268 |
help |
| 269 |
Power off and reset support for the ARM Ltd. Versatile |
| 270 |
Express boards. |
| 271 |
|
| 272 |
config POWER_RESET_XGENE |
| 273 |
bool "APM SoC X-Gene reset driver" |
| 274 |
depends on ARM64 |
| 275 |
help |
| 276 |
Reboot support for the APM SoC X-Gene Eval boards. |
| 277 |
|
| 278 |
config POWER_RESET_KEYSTONE |
| 279 |
bool "Keystone reset driver" |
| 280 |
depends on ARCH_KEYSTONE || COMPILE_TEST |
| 281 |
depends on HAS_IOMEM |
| 282 |
select MFD_SYSCON |
| 283 |
help |
| 284 |
Reboot support for the KEYSTONE SoCs. |
| 285 |
|
| 286 |
config POWER_RESET_SPACEMIT_P1 |
| 287 |
tristate "SpacemiT P1 poweroff and reset driver" |
| 288 |
depends on ARCH_SPACEMIT || COMPILE_TEST |
| 289 |
depends on MFD_SPACEMIT_P1 |
| 290 |
default MFD_SPACEMIT_P1 |
| 291 |
help |
| 292 |
This driver supports power-off and reset operations for the SpacemiT |
| 293 |
P1 PMIC. |
| 294 |
|
| 295 |
config POWER_RESET_SYSCON |
| 296 |
bool "Generic SYSCON regmap reset driver" |
| 297 |
depends on OF |
| 298 |
depends on HAS_IOMEM |
| 299 |
select MFD_SYSCON |
| 300 |
help |
| 301 |
Reboot support for generic SYSCON mapped register reset. |
| 302 |
|
| 303 |
config POWER_RESET_SYSCON_POWEROFF |
| 304 |
bool "Generic SYSCON regmap poweroff driver" |
| 305 |
depends on OF |
| 306 |
depends on HAS_IOMEM |
| 307 |
select MFD_SYSCON |
| 308 |
help |
| 309 |
Poweroff support for generic SYSCON mapped register poweroff. |
| 310 |
|
| 311 |
config POWER_RESET_RMOBILE |
| 312 |
tristate "Renesas R-Mobile reset driver" |
| 313 |
depends on ARCH_RMOBILE || COMPILE_TEST |
| 314 |
depends on HAS_IOMEM |
| 315 |
help |
| 316 |
Reboot support for Renesas R-Mobile and SH-Mobile SoCs. |
| 317 |
|
| 318 |
config REBOOT_MODE |
| 319 |
tristate |
| 320 |
|
| 321 |
config SYSCON_REBOOT_MODE |
| 322 |
tristate "Generic SYSCON regmap reboot mode driver" |
| 323 |
depends on OF |
| 324 |
depends on MFD_SYSCON |
| 325 |
select REBOOT_MODE |
| 326 |
help |
| 327 |
Say y here will enable reboot mode driver. This will |
| 328 |
get reboot mode arguments and store it in SYSCON mapped |
| 329 |
register, then the bootloader can read it to take different |
| 330 |
action according to the mode. |
| 331 |
|
| 332 |
config POWER_RESET_SC27XX |
| 333 |
tristate "Spreadtrum SC27xx PMIC power-off driver" |
| 334 |
depends on MFD_SC27XX_PMIC || COMPILE_TEST |
| 335 |
help |
| 336 |
This driver supports powering off a system through |
| 337 |
Spreadtrum SC27xx series PMICs. The SC27xx series |
| 338 |
PMICs includes the SC2720, SC2721, SC2723, SC2730 |
| 339 |
and SC2731 chips. |
| 340 |
|
| 341 |
config NVMEM_REBOOT_MODE |
| 342 |
tristate "Generic NVMEM reboot mode driver" |
| 343 |
depends on OF |
| 344 |
select REBOOT_MODE |
| 345 |
help |
| 346 |
Say y here will enable reboot mode driver. This will |
| 347 |
get reboot mode arguments and store it in a NVMEM cell, |
| 348 |
then the bootloader can read it and take different |
| 349 |
action according to the mode. |
| 350 |
|
| 351 |
config POWER_MLXBF |
| 352 |
tristate "Mellanox BlueField power handling driver" |
| 353 |
depends on (GPIO_MLXBF2 || GPIO_MLXBF3) && ACPI |
| 354 |
help |
| 355 |
This driver supports reset or low power mode handling for Mellanox BlueField. |
| 356 |
|
| 357 |
endif |