| 1 |
|
| 2 |
/* Linux device driver for RTL8180 / RTL8185 / RTL8187SE |
| 3 |
* |
| 4 |
* Copyright 2007 Michael Wu <[email protected]> |
| 5 |
* Copyright 2007,2014 Andrea Merello <[email protected]> |
| 6 |
* |
| 7 |
* Based on the r8180 driver, which is: |
| 8 |
* Copyright 2004-2005 Andrea Merello <[email protected]>, et al. |
| 9 |
* |
| 10 |
* Thanks to Realtek for their support! |
| 11 |
* |
| 12 |
************************************************************************ |
| 13 |
* |
| 14 |
* The driver was extended to the RTL8187SE in 2014 by |
| 15 |
* Andrea Merello <[email protected]> |
| 16 |
* |
| 17 |
* based also on: |
| 18 |
* - portions of rtl8187se Linux staging driver, Copyright Realtek corp. |
| 19 |
* (available in drivers/staging/rtl8187se directory of Linux 3.14) |
| 20 |
* - other GPL, unpublished (until now), Linux driver code, |
| 21 |
* Copyright Larry Finger <[email protected]> |
| 22 |
* |
| 23 |
* A huge thanks goes to Sara V. Nari who forgives me when I'm |
| 24 |
* sitting in front of my laptop at evening, week-end, night... |
| 25 |
* |
| 26 |
* A special thanks goes to Antonio Cuni, who helped me with |
| 27 |
* some python userspace stuff I used to debug RTL8187SE code, and who |
| 28 |
* bought a laptop with an unsupported Wi-Fi card some years ago... |
| 29 |
* |
| 30 |
* Thanks to Larry Finger for writing some code for rtl8187se and for |
| 31 |
* his suggestions. |
| 32 |
* |
| 33 |
* Thanks to Dan Carpenter for reviewing my initial patch and for his |
| 34 |
* suggestions. |
| 35 |
* |
| 36 |
* Thanks to Bernhard Schiffner for his help in testing and for his |
| 37 |
* suggestions. |
| 38 |
* |
| 39 |
************************************************************************ |
| 40 |
* |
| 41 |
* This program is free software; you can redistribute it and/or modify |
| 42 |
* it under the terms of the GNU General Public License version 2 as |
| 43 |
* published by the Free Software Foundation. |
| 44 |
*/ |
| 45 |
|
| 46 |
#include <linux/interrupt.h> |
| 47 |
#include <linux/pci.h> |
| 48 |
#include <linux/slab.h> |
| 49 |
#include <linux/delay.h> |
| 50 |
#include <linux/etherdevice.h> |
| 51 |
#include <linux/eeprom_93cx6.h> |
| 52 |
#include <linux/module.h> |
| 53 |
#include <net/mac80211.h> |
| 54 |
|
| 55 |
#include "rtl8180.h" |
| 56 |
#include "rtl8225.h" |
| 57 |
#include "sa2400.h" |
| 58 |
#include "max2820.h" |
| 59 |
#include "grf5101.h" |
| 60 |
#include "rtl8225se.h" |
| 61 |
|
| 62 |
MODULE_AUTHOR("Michael Wu <[email protected]>"); |
| 63 |
MODULE_AUTHOR("Andrea Merello <[email protected]>"); |
| 64 |
MODULE_DESCRIPTION("RTL8180 / RTL8185 / RTL8187SE PCI wireless driver"); |
| 65 |
MODULE_LICENSE("GPL"); |
| 66 |
|
| 67 |
static const struct pci_device_id rtl8180_table[] = { |
| 68 |
|
| 69 |
/* rtl8187se */ |
| 70 |
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8199) }, |
| 71 |
|
| 72 |
/* rtl8185 */ |
| 73 |
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8185) }, |
| 74 |
{ PCI_DEVICE(PCI_VENDOR_ID_BELKIN, 0x700f) }, |
| 75 |
{ PCI_DEVICE(PCI_VENDOR_ID_BELKIN, 0x701f) }, |
| 76 |
|
| 77 |
/* rtl8180 */ |
| 78 |
{ PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8180) }, |
| 79 |
{ PCI_DEVICE(0x1799, 0x6001) }, |
| 80 |
{ PCI_DEVICE(0x1799, 0x6020) }, |
| 81 |
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x3300) }, |
| 82 |
{ PCI_DEVICE(0x1186, 0x3301) }, |
| 83 |
{ PCI_DEVICE(0x1432, 0x7106) }, |
| 84 |
{ } |
| 85 |
}; |
| 86 |
|
| 87 |
MODULE_DEVICE_TABLE(pci, rtl8180_table); |
| 88 |
|
| 89 |
static const struct ieee80211_rate rtl818x_rates[] = { |
| 90 |
{ .bitrate = 10, .hw_value = 0, }, |
| 91 |
{ .bitrate = 20, .hw_value = 1, }, |
| 92 |
{ .bitrate = 55, .hw_value = 2, }, |
| 93 |
{ .bitrate = 110, .hw_value = 3, }, |
| 94 |
{ .bitrate = 60, .hw_value = 4, }, |
| 95 |
{ .bitrate = 90, .hw_value = 5, }, |
| 96 |
{ .bitrate = 120, .hw_value = 6, }, |
| 97 |
{ .bitrate = 180, .hw_value = 7, }, |
| 98 |
{ .bitrate = 240, .hw_value = 8, }, |
| 99 |
{ .bitrate = 360, .hw_value = 9, }, |
| 100 |
{ .bitrate = 480, .hw_value = 10, }, |
| 101 |
{ .bitrate = 540, .hw_value = 11, }, |
| 102 |
}; |
| 103 |
|
| 104 |
static const struct ieee80211_channel rtl818x_channels[] = { |
| 105 |
{ .center_freq = 2412 }, |
| 106 |
{ .center_freq = 2417 }, |
| 107 |
{ .center_freq = 2422 }, |
| 108 |
{ .center_freq = 2427 }, |
| 109 |
{ .center_freq = 2432 }, |
| 110 |
{ .center_freq = 2437 }, |
| 111 |
{ .center_freq = 2442 }, |
| 112 |
{ .center_freq = 2447 }, |
| 113 |
{ .center_freq = 2452 }, |
| 114 |
{ .center_freq = 2457 }, |
| 115 |
{ .center_freq = 2462 }, |
| 116 |
{ .center_freq = 2467 }, |
| 117 |
{ .center_freq = 2472 }, |
| 118 |
{ .center_freq = 2484 }, |
| 119 |
}; |
| 120 |
|
| 121 |
/* Queues for rtl8187se card |
| 122 |
* |
| 123 |
* name | reg | queue |
| 124 |
* BC | 7 | 6 |
| 125 |
* MG | 1 | 0 |
| 126 |
* HI | 6 | 1 |
| 127 |
* VO | 5 | 2 |
| 128 |
* VI | 4 | 3 |
| 129 |
* BE | 3 | 4 |
| 130 |
* BK | 2 | 5 |
| 131 |
* |
| 132 |
* The complete map for DMA kick reg using use all queue is: |
| 133 |
* static const int rtl8187se_queues_map[RTL8187SE_NR_TX_QUEUES] = |
| 134 |
* {1, 6, 5, 4, 3, 2, 7}; |
| 135 |
* |
| 136 |
* .. but.. Because for mac80211 4 queues are enough for QoS we use this |
| 137 |
* |
| 138 |
* name | reg | queue |
| 139 |
* BC | 7 | 4 <- currently not used yet |
| 140 |
* MG | 1 | x <- Not used |
| 141 |
* HI | 6 | x <- Not used |
| 142 |
* VO | 5 | 0 <- used |
| 143 |
* VI | 4 | 1 <- used |
| 144 |
* BE | 3 | 2 <- used |
| 145 |
* BK | 2 | 3 <- used |
| 146 |
* |
| 147 |
* Beacon queue could be used, but this is not finished yet. |
| 148 |
* |
| 149 |
* I thougth about using the other two queues but I decided not to do this: |
| 150 |
* |
| 151 |
* - I'm unsure whether the mac80211 will ever try to use more than 4 queues |
| 152 |
* by itself. |
| 153 |
* |
| 154 |
* - I could route MGMT frames (currently sent over VO queue) to the MGMT |
| 155 |
* queue but since mac80211 will do not know about it, I will probably gain |
| 156 |
* some HW priority whenever the VO queue is not empty, but this gain is |
| 157 |
* limited by the fact that I had to stop the mac80211 queue whenever one of |
| 158 |
* the VO or MGMT queues is full, stopping also submitting of MGMT frame |
| 159 |
* to the driver. |
| 160 |
* |
| 161 |
* - I don't know how to set in the HW the contention window params for MGMT |
| 162 |
* and HI-prio queues. |
| 163 |
*/ |
| 164 |
|
| 165 |
static const int rtl8187se_queues_map[RTL8187SE_NR_TX_QUEUES] = {5, 4, 3, 2, 7}; |
| 166 |
|
| 167 |
/* Queues for rtl8180/rtl8185 cards |
| 168 |
* |
| 169 |
* name | reg | prio |
| 170 |
* BC | 7 | 3 |
| 171 |
* HI | 6 | 0 |
| 172 |
* NO | 5 | 1 |
| 173 |
* LO | 4 | 2 |
| 174 |
* |
| 175 |
* The complete map for DMA kick reg using all queue is: |
| 176 |
* static const int rtl8180_queues_map[RTL8180_NR_TX_QUEUES] = {6, 5, 4, 7}; |
| 177 |
* |
| 178 |
* .. but .. Because the mac80211 needs at least 4 queues for QoS or |
| 179 |
* otherwise QoS can't be done, we use just one. |
| 180 |
* Beacon queue could be used, but this is not finished yet. |
| 181 |
* Actual map is: |
| 182 |
* |
| 183 |
* name | reg | prio |
| 184 |
* BC | 7 | 1 <- currently not used yet. |
| 185 |
* HI | 6 | x <- not used |
| 186 |
* NO | 5 | x <- not used |
| 187 |
* LO | 4 | 0 <- used |
| 188 |
*/ |
| 189 |
|
| 190 |
static const int rtl8180_queues_map[RTL8180_NR_TX_QUEUES] = {4, 7}; |
| 191 |
|
| 192 |
/* LNA gain table for rtl8187se */ |
| 193 |
static const u8 rtl8187se_lna_gain[4] = {02, 17, 29, 39}; |
| 194 |
|
| 195 |
void rtl8180_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data) |
| 196 |
{ |
| 197 |
struct rtl8180_priv *priv = dev->priv; |
| 198 |
int i = 10; |
| 199 |
u32 buf; |
| 200 |
|
| 201 |
buf = (data << 8) | addr; |
| 202 |
|
| 203 |
rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->PHY[0], buf | 0x80); |
| 204 |
while (i--) { |
| 205 |
rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->PHY[0], buf); |
| 206 |
if (rtl818x_ioread8(priv, &priv->map->PHY[2]) == (data & 0xFF)) |
| 207 |
return; |
| 208 |
} |
| 209 |
} |
| 210 |
|
| 211 |
static void rtl8180_handle_rx(struct ieee80211_hw *dev) |
| 212 |
{ |
| 213 |
struct rtl8180_priv *priv = dev->priv; |
| 214 |
struct rtl818x_rx_cmd_desc *cmd_desc; |
| 215 |
unsigned int count = 32; |
| 216 |
u8 agc, sq; |
| 217 |
s8 signal = 1; |
| 218 |
dma_addr_t mapping; |
| 219 |
|
| 220 |
while (count--) { |
| 221 |
void *entry = priv->rx_ring + priv->rx_idx * priv->rx_ring_sz; |
| 222 |
struct sk_buff *skb = priv->rx_buf[priv->rx_idx]; |
| 223 |
u32 flags, flags2, flags3 = 0; |
| 224 |
u64 tsft; |
| 225 |
|
| 226 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 227 |
struct rtl8187se_rx_desc *desc = entry; |
| 228 |
|
| 229 |
flags = le32_to_cpu(desc->flags); |
| 230 |
/* if ownership flag is set, then we can trust the |
| 231 |
* HW has written other fields. We must not trust |
| 232 |
* other descriptor data read before we checked (read) |
| 233 |
* the ownership flag |
| 234 |
*/ |
| 235 |
rmb(); |
| 236 |
flags3 = le32_to_cpu(desc->flags3); |
| 237 |
flags2 = le32_to_cpu(desc->flags2); |
| 238 |
tsft = le64_to_cpu(desc->tsft); |
| 239 |
} else { |
| 240 |
struct rtl8180_rx_desc *desc = entry; |
| 241 |
|
| 242 |
flags = le32_to_cpu(desc->flags); |
| 243 |
/* same as above */ |
| 244 |
rmb(); |
| 245 |
flags2 = le32_to_cpu(desc->flags2); |
| 246 |
tsft = le64_to_cpu(desc->tsft); |
| 247 |
} |
| 248 |
|
| 249 |
if (flags & RTL818X_RX_DESC_FLAG_OWN) |
| 250 |
return; |
| 251 |
|
| 252 |
if (unlikely(flags & (RTL818X_RX_DESC_FLAG_DMA_FAIL | |
| 253 |
RTL818X_RX_DESC_FLAG_FOF | |
| 254 |
RTL818X_RX_DESC_FLAG_RX_ERR))) |
| 255 |
goto done; |
| 256 |
else { |
| 257 |
struct ieee80211_rx_status rx_status = {0}; |
| 258 |
struct sk_buff *new_skb = dev_alloc_skb(MAX_RX_SIZE); |
| 259 |
|
| 260 |
if (unlikely(!new_skb)) |
| 261 |
goto done; |
| 262 |
|
| 263 |
mapping = dma_map_single(&priv->pdev->dev, |
| 264 |
skb_tail_pointer(new_skb), |
| 265 |
MAX_RX_SIZE, DMA_FROM_DEVICE); |
| 266 |
|
| 267 |
if (dma_mapping_error(&priv->pdev->dev, mapping)) { |
| 268 |
kfree_skb(new_skb); |
| 269 |
dev_err(&priv->pdev->dev, "RX DMA map error\n"); |
| 270 |
|
| 271 |
goto done; |
| 272 |
} |
| 273 |
|
| 274 |
dma_unmap_single(&priv->pdev->dev, |
| 275 |
*((dma_addr_t *)skb->cb), |
| 276 |
MAX_RX_SIZE, DMA_FROM_DEVICE); |
| 277 |
skb_put(skb, flags & 0xFFF); |
| 278 |
|
| 279 |
rx_status.antenna = (flags2 >> 15) & 1; |
| 280 |
rx_status.rate_idx = (flags >> 20) & 0xF; |
| 281 |
agc = (flags2 >> 17) & 0x7F; |
| 282 |
|
| 283 |
switch (priv->chip_family) { |
| 284 |
case RTL818X_CHIP_FAMILY_RTL8185: |
| 285 |
if (rx_status.rate_idx > 3) |
| 286 |
signal = -clamp_t(u8, agc, 25, 90) - 9; |
| 287 |
else |
| 288 |
signal = -clamp_t(u8, agc, 30, 95); |
| 289 |
break; |
| 290 |
case RTL818X_CHIP_FAMILY_RTL8180: |
| 291 |
sq = flags2 & 0xff; |
| 292 |
signal = priv->rf->calc_rssi(agc, sq); |
| 293 |
break; |
| 294 |
case RTL818X_CHIP_FAMILY_RTL8187SE: |
| 295 |
/* OFDM measure reported by HW is signed, |
| 296 |
* in 0.5dBm unit, with zero centered @ -41dBm |
| 297 |
* input signal. |
| 298 |
*/ |
| 299 |
if (rx_status.rate_idx > 3) { |
| 300 |
signal = (s8)((flags3 >> 16) & 0xff); |
| 301 |
signal = signal / 2 - 41; |
| 302 |
} else { |
| 303 |
int idx, bb; |
| 304 |
|
| 305 |
idx = (agc & 0x60) >> 5; |
| 306 |
bb = (agc & 0x1F) * 2; |
| 307 |
/* bias + BB gain + LNA gain */ |
| 308 |
signal = 4 - bb - rtl8187se_lna_gain[idx]; |
| 309 |
} |
| 310 |
break; |
| 311 |
} |
| 312 |
rx_status.signal = signal; |
| 313 |
rx_status.freq = dev->conf.chandef.chan->center_freq; |
| 314 |
rx_status.band = dev->conf.chandef.chan->band; |
| 315 |
rx_status.mactime = tsft; |
| 316 |
rx_status.flag |= RX_FLAG_MACTIME_START; |
| 317 |
if (flags & RTL818X_RX_DESC_FLAG_SPLCP) |
| 318 |
rx_status.enc_flags |= RX_ENC_FLAG_SHORTPRE; |
| 319 |
if (flags & RTL818X_RX_DESC_FLAG_CRC32_ERR) |
| 320 |
rx_status.flag |= RX_FLAG_FAILED_FCS_CRC; |
| 321 |
|
| 322 |
memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status)); |
| 323 |
ieee80211_rx_irqsafe(dev, skb); |
| 324 |
|
| 325 |
skb = new_skb; |
| 326 |
priv->rx_buf[priv->rx_idx] = skb; |
| 327 |
*((dma_addr_t *) skb->cb) = mapping; |
| 328 |
} |
| 329 |
|
| 330 |
done: |
| 331 |
cmd_desc = entry; |
| 332 |
cmd_desc->rx_buf = cpu_to_le32(*((dma_addr_t *)skb->cb)); |
| 333 |
cmd_desc->flags = cpu_to_le32(RTL818X_RX_DESC_FLAG_OWN | |
| 334 |
MAX_RX_SIZE); |
| 335 |
if (priv->rx_idx == 31) |
| 336 |
cmd_desc->flags |= |
| 337 |
cpu_to_le32(RTL818X_RX_DESC_FLAG_EOR); |
| 338 |
priv->rx_idx = (priv->rx_idx + 1) % 32; |
| 339 |
} |
| 340 |
} |
| 341 |
|
| 342 |
static void rtl8180_handle_tx(struct ieee80211_hw *dev, unsigned int prio) |
| 343 |
{ |
| 344 |
struct rtl8180_priv *priv = dev->priv; |
| 345 |
struct rtl8180_tx_ring *ring = &priv->tx_ring[prio]; |
| 346 |
|
| 347 |
while (skb_queue_len(&ring->queue)) { |
| 348 |
struct rtl8180_tx_desc *entry = &ring->desc[ring->idx]; |
| 349 |
struct sk_buff *skb; |
| 350 |
struct ieee80211_tx_info *info; |
| 351 |
u32 flags = le32_to_cpu(entry->flags); |
| 352 |
|
| 353 |
if (flags & RTL818X_TX_DESC_FLAG_OWN) |
| 354 |
return; |
| 355 |
|
| 356 |
ring->idx = (ring->idx + 1) % ring->entries; |
| 357 |
skb = __skb_dequeue(&ring->queue); |
| 358 |
dma_unmap_single(&priv->pdev->dev, le32_to_cpu(entry->tx_buf), |
| 359 |
skb->len, DMA_TO_DEVICE); |
| 360 |
|
| 361 |
info = IEEE80211_SKB_CB(skb); |
| 362 |
ieee80211_tx_info_clear_status(info); |
| 363 |
|
| 364 |
if (!(info->flags & IEEE80211_TX_CTL_NO_ACK) && |
| 365 |
(flags & RTL818X_TX_DESC_FLAG_TX_OK)) |
| 366 |
info->flags |= IEEE80211_TX_STAT_ACK; |
| 367 |
|
| 368 |
info->status.rates[0].count = (flags & 0xFF) + 1; |
| 369 |
|
| 370 |
ieee80211_tx_status_irqsafe(dev, skb); |
| 371 |
if (ring->entries - skb_queue_len(&ring->queue) == 2) |
| 372 |
ieee80211_wake_queue(dev, prio); |
| 373 |
} |
| 374 |
} |
| 375 |
|
| 376 |
static irqreturn_t rtl8187se_interrupt(int irq, void *dev_id) |
| 377 |
{ |
| 378 |
struct ieee80211_hw *dev = dev_id; |
| 379 |
struct rtl8180_priv *priv = dev->priv; |
| 380 |
u32 reg; |
| 381 |
unsigned long flags; |
| 382 |
static int desc_err; |
| 383 |
|
| 384 |
spin_lock_irqsave(&priv->lock, flags); |
| 385 |
/* Note: 32-bit interrupt status */ |
| 386 |
reg = rtl818x_ioread32(priv, &priv->map->INT_STATUS_SE); |
| 387 |
if (unlikely(reg == 0xFFFFFFFF)) { |
| 388 |
spin_unlock_irqrestore(&priv->lock, flags); |
| 389 |
return IRQ_HANDLED; |
| 390 |
} |
| 391 |
|
| 392 |
rtl818x_iowrite32(priv, &priv->map->INT_STATUS_SE, reg); |
| 393 |
|
| 394 |
if (reg & IMR_TIMEOUT1) |
| 395 |
rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0); |
| 396 |
|
| 397 |
if (reg & (IMR_TBDOK | IMR_TBDER)) |
| 398 |
rtl8180_handle_tx(dev, 4); |
| 399 |
|
| 400 |
if (reg & (IMR_TVODOK | IMR_TVODER)) |
| 401 |
rtl8180_handle_tx(dev, 0); |
| 402 |
|
| 403 |
if (reg & (IMR_TVIDOK | IMR_TVIDER)) |
| 404 |
rtl8180_handle_tx(dev, 1); |
| 405 |
|
| 406 |
if (reg & (IMR_TBEDOK | IMR_TBEDER)) |
| 407 |
rtl8180_handle_tx(dev, 2); |
| 408 |
|
| 409 |
if (reg & (IMR_TBKDOK | IMR_TBKDER)) |
| 410 |
rtl8180_handle_tx(dev, 3); |
| 411 |
|
| 412 |
if (reg & (IMR_ROK | IMR_RER | RTL818X_INT_SE_RX_DU | IMR_RQOSOK)) |
| 413 |
rtl8180_handle_rx(dev); |
| 414 |
/* The interface sometimes generates several RX DMA descriptor errors |
| 415 |
* at startup. Do not report these. |
| 416 |
*/ |
| 417 |
if ((reg & RTL818X_INT_SE_RX_DU) && desc_err++ > 2) |
| 418 |
if (net_ratelimit()) |
| 419 |
wiphy_err(dev->wiphy, "No RX DMA Descriptor avail\n"); |
| 420 |
|
| 421 |
spin_unlock_irqrestore(&priv->lock, flags); |
| 422 |
return IRQ_HANDLED; |
| 423 |
} |
| 424 |
|
| 425 |
static irqreturn_t rtl8180_interrupt(int irq, void *dev_id) |
| 426 |
{ |
| 427 |
struct ieee80211_hw *dev = dev_id; |
| 428 |
struct rtl8180_priv *priv = dev->priv; |
| 429 |
u16 reg; |
| 430 |
|
| 431 |
spin_lock(&priv->lock); |
| 432 |
reg = rtl818x_ioread16(priv, &priv->map->INT_STATUS); |
| 433 |
if (unlikely(reg == 0xFFFF)) { |
| 434 |
spin_unlock(&priv->lock); |
| 435 |
return IRQ_HANDLED; |
| 436 |
} |
| 437 |
|
| 438 |
rtl818x_iowrite16(priv, &priv->map->INT_STATUS, reg); |
| 439 |
|
| 440 |
if (reg & (RTL818X_INT_TXB_OK | RTL818X_INT_TXB_ERR)) |
| 441 |
rtl8180_handle_tx(dev, 1); |
| 442 |
|
| 443 |
if (reg & (RTL818X_INT_TXL_OK | RTL818X_INT_TXL_ERR)) |
| 444 |
rtl8180_handle_tx(dev, 0); |
| 445 |
|
| 446 |
if (reg & (RTL818X_INT_RX_OK | RTL818X_INT_RX_ERR)) |
| 447 |
rtl8180_handle_rx(dev); |
| 448 |
|
| 449 |
spin_unlock(&priv->lock); |
| 450 |
|
| 451 |
return IRQ_HANDLED; |
| 452 |
} |
| 453 |
|
| 454 |
static void rtl8180_tx(struct ieee80211_hw *dev, |
| 455 |
struct ieee80211_tx_control *control, |
| 456 |
struct sk_buff *skb) |
| 457 |
{ |
| 458 |
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| 459 |
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; |
| 460 |
struct rtl8180_priv *priv = dev->priv; |
| 461 |
struct rtl8180_tx_ring *ring; |
| 462 |
struct rtl8180_tx_desc *entry; |
| 463 |
unsigned int prio = 0; |
| 464 |
unsigned long flags; |
| 465 |
unsigned int idx, hw_prio; |
| 466 |
|
| 467 |
dma_addr_t mapping; |
| 468 |
u32 tx_flags; |
| 469 |
u8 rc_flags; |
| 470 |
u16 plcp_len = 0; |
| 471 |
__le16 rts_duration = 0; |
| 472 |
/* do arithmetic and then convert to le16 */ |
| 473 |
u16 frame_duration = 0; |
| 474 |
|
| 475 |
/* rtl8180/rtl8185 only has one useable tx queue */ |
| 476 |
if (dev->queues > IEEE80211_AC_BK) |
| 477 |
prio = skb_get_queue_mapping(skb); |
| 478 |
ring = &priv->tx_ring[prio]; |
| 479 |
|
| 480 |
mapping = dma_map_single(&priv->pdev->dev, skb->data, skb->len, |
| 481 |
DMA_TO_DEVICE); |
| 482 |
|
| 483 |
if (dma_mapping_error(&priv->pdev->dev, mapping)) { |
| 484 |
kfree_skb(skb); |
| 485 |
dev_err(&priv->pdev->dev, "TX DMA mapping error\n"); |
| 486 |
return; |
| 487 |
} |
| 488 |
|
| 489 |
tx_flags = RTL818X_TX_DESC_FLAG_OWN | RTL818X_TX_DESC_FLAG_FS | |
| 490 |
RTL818X_TX_DESC_FLAG_LS | |
| 491 |
(ieee80211_get_tx_rate(dev, info)->hw_value << 24) | |
| 492 |
skb->len; |
| 493 |
|
| 494 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) |
| 495 |
tx_flags |= RTL818X_TX_DESC_FLAG_DMA | |
| 496 |
RTL818X_TX_DESC_FLAG_NO_ENC; |
| 497 |
|
| 498 |
rc_flags = info->control.rates[0].flags; |
| 499 |
|
| 500 |
/* HW will perform RTS-CTS when only RTS flags is set. |
| 501 |
* HW will perform CTS-to-self when both RTS and CTS flags are set. |
| 502 |
* RTS rate and RTS duration will be used also for CTS-to-self. |
| 503 |
*/ |
| 504 |
if (rc_flags & IEEE80211_TX_RC_USE_RTS_CTS) { |
| 505 |
tx_flags |= RTL818X_TX_DESC_FLAG_RTS; |
| 506 |
tx_flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19; |
| 507 |
rts_duration = ieee80211_rts_duration(dev, priv->vif, |
| 508 |
skb->len, info); |
| 509 |
} else if (rc_flags & IEEE80211_TX_RC_USE_CTS_PROTECT) { |
| 510 |
tx_flags |= RTL818X_TX_DESC_FLAG_RTS | RTL818X_TX_DESC_FLAG_CTS; |
| 511 |
tx_flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19; |
| 512 |
rts_duration = ieee80211_ctstoself_duration(dev, priv->vif, |
| 513 |
skb->len, info); |
| 514 |
} |
| 515 |
|
| 516 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) { |
| 517 |
unsigned int remainder; |
| 518 |
|
| 519 |
plcp_len = DIV_ROUND_UP(16 * (skb->len + 4), |
| 520 |
(ieee80211_get_tx_rate(dev, info)->bitrate * 2) / 10); |
| 521 |
remainder = (16 * (skb->len + 4)) % |
| 522 |
((ieee80211_get_tx_rate(dev, info)->bitrate * 2) / 10); |
| 523 |
if (remainder <= 6) |
| 524 |
plcp_len |= 1 << 15; |
| 525 |
} |
| 526 |
|
| 527 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 528 |
__le16 duration; |
| 529 |
/* SIFS time (required by HW) is already included by |
| 530 |
* ieee80211_generic_frame_duration |
| 531 |
*/ |
| 532 |
duration = ieee80211_generic_frame_duration(dev, priv->vif, |
| 533 |
NL80211_BAND_2GHZ, skb->len, |
| 534 |
ieee80211_get_tx_rate(dev, info)); |
| 535 |
|
| 536 |
frame_duration = priv->ack_time + le16_to_cpu(duration); |
| 537 |
} |
| 538 |
|
| 539 |
spin_lock_irqsave(&priv->lock, flags); |
| 540 |
|
| 541 |
if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) { |
| 542 |
if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT) |
| 543 |
priv->seqno += 0x10; |
| 544 |
hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG); |
| 545 |
hdr->seq_ctrl |= cpu_to_le16(priv->seqno); |
| 546 |
} |
| 547 |
|
| 548 |
idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries; |
| 549 |
entry = &ring->desc[idx]; |
| 550 |
|
| 551 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 552 |
entry->frame_duration = cpu_to_le16(frame_duration); |
| 553 |
entry->frame_len_se = cpu_to_le16(skb->len); |
| 554 |
|
| 555 |
/* tpc polarity */ |
| 556 |
entry->flags3 = cpu_to_le16(1<<4); |
| 557 |
} else |
| 558 |
entry->frame_len = cpu_to_le32(skb->len); |
| 559 |
|
| 560 |
entry->rts_duration = rts_duration; |
| 561 |
entry->plcp_len = cpu_to_le16(plcp_len); |
| 562 |
entry->tx_buf = cpu_to_le32(mapping); |
| 563 |
|
| 564 |
entry->retry_limit = info->control.rates[0].count - 1; |
| 565 |
|
| 566 |
/* We must be sure that tx_flags is written last because the HW |
| 567 |
* looks at it to check if the rest of data is valid or not |
| 568 |
*/ |
| 569 |
wmb(); |
| 570 |
entry->flags = cpu_to_le32(tx_flags); |
| 571 |
/* We must be sure this has been written before followings HW |
| 572 |
* register write, because this write will made the HW attempts |
| 573 |
* to DMA the just-written data |
| 574 |
*/ |
| 575 |
wmb(); |
| 576 |
|
| 577 |
__skb_queue_tail(&ring->queue, skb); |
| 578 |
if (ring->entries - skb_queue_len(&ring->queue) < 2) |
| 579 |
ieee80211_stop_queue(dev, prio); |
| 580 |
|
| 581 |
spin_unlock_irqrestore(&priv->lock, flags); |
| 582 |
|
| 583 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 584 |
/* just poll: rings are stopped with TPPollStop reg */ |
| 585 |
hw_prio = rtl8187se_queues_map[prio]; |
| 586 |
rtl818x_iowrite8(priv, &priv->map->TX_DMA_POLLING, |
| 587 |
(1 << hw_prio)); |
| 588 |
} else { |
| 589 |
hw_prio = rtl8180_queues_map[prio]; |
| 590 |
rtl818x_iowrite8(priv, &priv->map->TX_DMA_POLLING, |
| 591 |
(1 << hw_prio) | /* ring to poll */ |
| 592 |
(1<<1) | (1<<2));/* stopped rings */ |
| 593 |
} |
| 594 |
} |
| 595 |
|
| 596 |
static void rtl8180_set_anaparam3(struct rtl8180_priv *priv, u16 anaparam3) |
| 597 |
{ |
| 598 |
u8 reg; |
| 599 |
|
| 600 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 601 |
RTL818X_EEPROM_CMD_CONFIG); |
| 602 |
|
| 603 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); |
| 604 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, |
| 605 |
reg | RTL818X_CONFIG3_ANAPARAM_WRITE); |
| 606 |
|
| 607 |
rtl818x_iowrite16(priv, &priv->map->ANAPARAM3, anaparam3); |
| 608 |
|
| 609 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, |
| 610 |
reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); |
| 611 |
|
| 612 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 613 |
RTL818X_EEPROM_CMD_NORMAL); |
| 614 |
} |
| 615 |
|
| 616 |
void rtl8180_set_anaparam2(struct rtl8180_priv *priv, u32 anaparam2) |
| 617 |
{ |
| 618 |
u8 reg; |
| 619 |
|
| 620 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 621 |
RTL818X_EEPROM_CMD_CONFIG); |
| 622 |
|
| 623 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); |
| 624 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, |
| 625 |
reg | RTL818X_CONFIG3_ANAPARAM_WRITE); |
| 626 |
|
| 627 |
rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, anaparam2); |
| 628 |
|
| 629 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, |
| 630 |
reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); |
| 631 |
|
| 632 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 633 |
RTL818X_EEPROM_CMD_NORMAL); |
| 634 |
} |
| 635 |
|
| 636 |
void rtl8180_set_anaparam(struct rtl8180_priv *priv, u32 anaparam) |
| 637 |
{ |
| 638 |
u8 reg; |
| 639 |
|
| 640 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 641 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); |
| 642 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, |
| 643 |
reg | RTL818X_CONFIG3_ANAPARAM_WRITE); |
| 644 |
rtl818x_iowrite32(priv, &priv->map->ANAPARAM, anaparam); |
| 645 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, |
| 646 |
reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); |
| 647 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 648 |
} |
| 649 |
|
| 650 |
static void rtl8187se_mac_config(struct ieee80211_hw *dev) |
| 651 |
{ |
| 652 |
struct rtl8180_priv *priv = dev->priv; |
| 653 |
u8 reg; |
| 654 |
|
| 655 |
rtl818x_iowrite32(priv, REG_ADDR4(0x1F0), 0); |
| 656 |
rtl818x_ioread32(priv, REG_ADDR4(0x1F0)); |
| 657 |
rtl818x_iowrite32(priv, REG_ADDR4(0x1F4), 0); |
| 658 |
rtl818x_ioread32(priv, REG_ADDR4(0x1F4)); |
| 659 |
rtl818x_iowrite8(priv, REG_ADDR1(0x1F8), 0); |
| 660 |
rtl818x_ioread8(priv, REG_ADDR1(0x1F8)); |
| 661 |
/* Enable DA10 TX power saving */ |
| 662 |
reg = rtl818x_ioread8(priv, &priv->map->PHY_PR); |
| 663 |
rtl818x_iowrite8(priv, &priv->map->PHY_PR, reg | 0x04); |
| 664 |
/* Power */ |
| 665 |
rtl818x_iowrite16(priv, PI_DATA_REG, 0x1000); |
| 666 |
rtl818x_iowrite16(priv, SI_DATA_REG, 0x1000); |
| 667 |
/* AFE - default to power ON */ |
| 668 |
rtl818x_iowrite16(priv, REG_ADDR2(0x370), 0x0560); |
| 669 |
rtl818x_iowrite16(priv, REG_ADDR2(0x372), 0x0560); |
| 670 |
rtl818x_iowrite16(priv, REG_ADDR2(0x374), 0x0DA4); |
| 671 |
rtl818x_iowrite16(priv, REG_ADDR2(0x376), 0x0DA4); |
| 672 |
rtl818x_iowrite16(priv, REG_ADDR2(0x378), 0x0560); |
| 673 |
rtl818x_iowrite16(priv, REG_ADDR2(0x37A), 0x0560); |
| 674 |
rtl818x_iowrite16(priv, REG_ADDR2(0x37C), 0x00EC); |
| 675 |
rtl818x_iowrite16(priv, REG_ADDR2(0x37E), 0x00EC); |
| 676 |
rtl818x_iowrite8(priv, REG_ADDR1(0x24E), 0x01); |
| 677 |
/* unknown, needed for suspend to RAM resume */ |
| 678 |
rtl818x_iowrite8(priv, REG_ADDR1(0x0A), 0x72); |
| 679 |
} |
| 680 |
|
| 681 |
static void rtl8187se_set_antenna_config(struct ieee80211_hw *dev, u8 def_ant, |
| 682 |
bool diversity) |
| 683 |
{ |
| 684 |
struct rtl8180_priv *priv = dev->priv; |
| 685 |
|
| 686 |
rtl8225_write_phy_cck(dev, 0x0C, 0x09); |
| 687 |
if (diversity) { |
| 688 |
if (def_ant == 1) { |
| 689 |
rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x00); |
| 690 |
rtl8225_write_phy_cck(dev, 0x11, 0xBB); |
| 691 |
rtl8225_write_phy_cck(dev, 0x01, 0xC7); |
| 692 |
rtl8225_write_phy_ofdm(dev, 0x0D, 0x54); |
| 693 |
rtl8225_write_phy_ofdm(dev, 0x18, 0xB2); |
| 694 |
} else { /* main antenna */ |
| 695 |
rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); |
| 696 |
rtl8225_write_phy_cck(dev, 0x11, 0x9B); |
| 697 |
rtl8225_write_phy_cck(dev, 0x01, 0xC7); |
| 698 |
rtl8225_write_phy_ofdm(dev, 0x0D, 0x5C); |
| 699 |
rtl8225_write_phy_ofdm(dev, 0x18, 0xB2); |
| 700 |
} |
| 701 |
} else { /* disable antenna diversity */ |
| 702 |
if (def_ant == 1) { |
| 703 |
rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x00); |
| 704 |
rtl8225_write_phy_cck(dev, 0x11, 0xBB); |
| 705 |
rtl8225_write_phy_cck(dev, 0x01, 0x47); |
| 706 |
rtl8225_write_phy_ofdm(dev, 0x0D, 0x54); |
| 707 |
rtl8225_write_phy_ofdm(dev, 0x18, 0x32); |
| 708 |
} else { /* main antenna */ |
| 709 |
rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); |
| 710 |
rtl8225_write_phy_cck(dev, 0x11, 0x9B); |
| 711 |
rtl8225_write_phy_cck(dev, 0x01, 0x47); |
| 712 |
rtl8225_write_phy_ofdm(dev, 0x0D, 0x5C); |
| 713 |
rtl8225_write_phy_ofdm(dev, 0x18, 0x32); |
| 714 |
} |
| 715 |
} |
| 716 |
/* priv->curr_ant = def_ant; */ |
| 717 |
} |
| 718 |
|
| 719 |
static void rtl8180_int_enable(struct ieee80211_hw *dev) |
| 720 |
{ |
| 721 |
struct rtl8180_priv *priv = dev->priv; |
| 722 |
|
| 723 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 724 |
rtl818x_iowrite32(priv, &priv->map->IMR, |
| 725 |
IMR_TBDER | IMR_TBDOK | |
| 726 |
IMR_TVODER | IMR_TVODOK | |
| 727 |
IMR_TVIDER | IMR_TVIDOK | |
| 728 |
IMR_TBEDER | IMR_TBEDOK | |
| 729 |
IMR_TBKDER | IMR_TBKDOK | |
| 730 |
IMR_RDU | IMR_RER | |
| 731 |
IMR_ROK | IMR_RQOSOK); |
| 732 |
} else { |
| 733 |
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF); |
| 734 |
} |
| 735 |
} |
| 736 |
|
| 737 |
static void rtl8180_int_disable(struct ieee80211_hw *dev) |
| 738 |
{ |
| 739 |
struct rtl8180_priv *priv = dev->priv; |
| 740 |
|
| 741 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 742 |
rtl818x_iowrite32(priv, &priv->map->IMR, 0); |
| 743 |
} else { |
| 744 |
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); |
| 745 |
} |
| 746 |
} |
| 747 |
|
| 748 |
static void rtl8180_conf_basic_rates(struct ieee80211_hw *dev, |
| 749 |
u32 basic_mask) |
| 750 |
{ |
| 751 |
struct rtl8180_priv *priv = dev->priv; |
| 752 |
u16 reg; |
| 753 |
u32 resp_mask; |
| 754 |
u8 basic_max; |
| 755 |
u8 resp_max, resp_min; |
| 756 |
|
| 757 |
resp_mask = basic_mask; |
| 758 |
/* IEEE80211 says the response rate should be equal to the highest basic |
| 759 |
* rate that is not faster than received frame. But it says also that if |
| 760 |
* the basic rate set does not contains any rate for the current |
| 761 |
* modulation class then mandatory rate set must be used for that |
| 762 |
* modulation class. Eventually add OFDM mandatory rates.. |
| 763 |
*/ |
| 764 |
if ((resp_mask & 0xf) == resp_mask) |
| 765 |
resp_mask |= 0x150; /* 6, 12, 24Mbps */ |
| 766 |
|
| 767 |
switch (priv->chip_family) { |
| 768 |
|
| 769 |
case RTL818X_CHIP_FAMILY_RTL8180: |
| 770 |
/* in 8180 this is NOT a BITMAP */ |
| 771 |
basic_max = fls(basic_mask) - 1; |
| 772 |
reg = rtl818x_ioread16(priv, &priv->map->BRSR); |
| 773 |
reg &= ~3; |
| 774 |
reg |= basic_max; |
| 775 |
rtl818x_iowrite16(priv, &priv->map->BRSR, reg); |
| 776 |
break; |
| 777 |
|
| 778 |
case RTL818X_CHIP_FAMILY_RTL8185: |
| 779 |
resp_max = fls(resp_mask) - 1; |
| 780 |
resp_min = ffs(resp_mask) - 1; |
| 781 |
/* in 8185 this is a BITMAP */ |
| 782 |
rtl818x_iowrite16(priv, &priv->map->BRSR, basic_mask); |
| 783 |
rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (resp_max << 4) | |
| 784 |
resp_min); |
| 785 |
break; |
| 786 |
|
| 787 |
case RTL818X_CHIP_FAMILY_RTL8187SE: |
| 788 |
/* in 8187se this is a BITMAP. BRSR reg actually sets |
| 789 |
* response rates. |
| 790 |
*/ |
| 791 |
rtl818x_iowrite16(priv, &priv->map->BRSR_8187SE, resp_mask); |
| 792 |
break; |
| 793 |
} |
| 794 |
} |
| 795 |
|
| 796 |
static void rtl8180_config_cardbus(struct ieee80211_hw *dev) |
| 797 |
{ |
| 798 |
struct rtl8180_priv *priv = dev->priv; |
| 799 |
u16 reg16; |
| 800 |
u8 reg8; |
| 801 |
|
| 802 |
reg8 = rtl818x_ioread8(priv, &priv->map->CONFIG3); |
| 803 |
reg8 |= 1 << 1; |
| 804 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg8); |
| 805 |
|
| 806 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 807 |
rtl818x_iowrite16(priv, FEMR_SE, 0xffff); |
| 808 |
} else { |
| 809 |
reg16 = rtl818x_ioread16(priv, &priv->map->FEMR); |
| 810 |
reg16 |= (1 << 15) | (1 << 14) | (1 << 4); |
| 811 |
rtl818x_iowrite16(priv, &priv->map->FEMR, reg16); |
| 812 |
} |
| 813 |
|
| 814 |
} |
| 815 |
|
| 816 |
static int rtl8180_init_hw(struct ieee80211_hw *dev) |
| 817 |
{ |
| 818 |
struct rtl8180_priv *priv = dev->priv; |
| 819 |
u16 reg; |
| 820 |
u32 reg32; |
| 821 |
|
| 822 |
rtl818x_iowrite8(priv, &priv->map->CMD, 0); |
| 823 |
rtl818x_ioread8(priv, &priv->map->CMD); |
| 824 |
msleep(10); |
| 825 |
|
| 826 |
/* reset */ |
| 827 |
rtl8180_int_disable(dev); |
| 828 |
rtl818x_ioread8(priv, &priv->map->CMD); |
| 829 |
|
| 830 |
reg = rtl818x_ioread8(priv, &priv->map->CMD); |
| 831 |
reg &= (1 << 1); |
| 832 |
reg |= RTL818X_CMD_RESET; |
| 833 |
rtl818x_iowrite8(priv, &priv->map->CMD, RTL818X_CMD_RESET); |
| 834 |
rtl818x_ioread8(priv, &priv->map->CMD); |
| 835 |
msleep(200); |
| 836 |
|
| 837 |
/* check success of reset */ |
| 838 |
if (rtl818x_ioread8(priv, &priv->map->CMD) & RTL818X_CMD_RESET) { |
| 839 |
wiphy_err(dev->wiphy, "reset timeout!\n"); |
| 840 |
return -ETIMEDOUT; |
| 841 |
} |
| 842 |
|
| 843 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD); |
| 844 |
rtl818x_ioread8(priv, &priv->map->CMD); |
| 845 |
msleep(200); |
| 846 |
|
| 847 |
if (rtl818x_ioread8(priv, &priv->map->CONFIG3) & (1 << 3)) { |
| 848 |
rtl8180_config_cardbus(dev); |
| 849 |
} |
| 850 |
|
| 851 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 852 |
rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA); |
| 853 |
else |
| 854 |
rtl818x_iowrite8(priv, &priv->map->MSR, 0); |
| 855 |
|
| 856 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) |
| 857 |
rtl8180_set_anaparam(priv, priv->anaparam); |
| 858 |
|
| 859 |
rtl818x_iowrite32(priv, &priv->map->RDSAR, priv->rx_ring_dma); |
| 860 |
/* mac80211 queue have higher prio for lower index. The last queue |
| 861 |
* (that mac80211 is not aware of) is reserved for beacons (and have |
| 862 |
* the highest priority on the NIC) |
| 863 |
*/ |
| 864 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 865 |
rtl818x_iowrite32(priv, &priv->map->TBDA, |
| 866 |
priv->tx_ring[1].dma); |
| 867 |
rtl818x_iowrite32(priv, &priv->map->TLPDA, |
| 868 |
priv->tx_ring[0].dma); |
| 869 |
} else { |
| 870 |
rtl818x_iowrite32(priv, &priv->map->TBDA, |
| 871 |
priv->tx_ring[4].dma); |
| 872 |
rtl818x_iowrite32(priv, &priv->map->TVODA, |
| 873 |
priv->tx_ring[0].dma); |
| 874 |
rtl818x_iowrite32(priv, &priv->map->TVIDA, |
| 875 |
priv->tx_ring[1].dma); |
| 876 |
rtl818x_iowrite32(priv, &priv->map->TBEDA, |
| 877 |
priv->tx_ring[2].dma); |
| 878 |
rtl818x_iowrite32(priv, &priv->map->TBKDA, |
| 879 |
priv->tx_ring[3].dma); |
| 880 |
} |
| 881 |
|
| 882 |
/* TODO: necessary? specs indicate not */ |
| 883 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 884 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG2); |
| 885 |
rtl818x_iowrite8(priv, &priv->map->CONFIG2, reg & ~(1 << 3)); |
| 886 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185) { |
| 887 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG2); |
| 888 |
rtl818x_iowrite8(priv, &priv->map->CONFIG2, reg | (1 << 4)); |
| 889 |
} |
| 890 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 891 |
|
| 892 |
/* TODO: set CONFIG5 for calibrating AGC on rtl8180 + philips radio? */ |
| 893 |
|
| 894 |
/* TODO: turn off hw wep on rtl8180 */ |
| 895 |
|
| 896 |
rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0); |
| 897 |
|
| 898 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { |
| 899 |
rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0); |
| 900 |
rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0); |
| 901 |
} else { |
| 902 |
rtl818x_iowrite8(priv, &priv->map->SECURITY, 0); |
| 903 |
|
| 904 |
rtl818x_iowrite8(priv, &priv->map->PHY_DELAY, 0x6); |
| 905 |
rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER, 0x4C); |
| 906 |
} |
| 907 |
|
| 908 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185) { |
| 909 |
/* TODO: set ClkRun enable? necessary? */ |
| 910 |
reg = rtl818x_ioread8(priv, &priv->map->GP_ENABLE); |
| 911 |
rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, reg & ~(1 << 6)); |
| 912 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 913 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); |
| 914 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | (1 << 2)); |
| 915 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 916 |
/* fix eccessive IFS after CTS-to-self */ |
| 917 |
if (priv->map_pio) { |
| 918 |
u8 reg; |
| 919 |
|
| 920 |
reg = rtl818x_ioread8(priv, &priv->map->PGSELECT); |
| 921 |
rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1); |
| 922 |
rtl818x_iowrite8(priv, REG_ADDR1(0xff), 0x35); |
| 923 |
rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg); |
| 924 |
} else |
| 925 |
rtl818x_iowrite8(priv, REG_ADDR1(0x1ff), 0x35); |
| 926 |
} |
| 927 |
|
| 928 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 929 |
|
| 930 |
/* the set auto rate fallback bitmask from 1M to 54 Mb/s */ |
| 931 |
rtl818x_iowrite16(priv, ARFR, 0xFFF); |
| 932 |
rtl818x_ioread16(priv, ARFR); |
| 933 |
|
| 934 |
/* stop unused queus (no dma alloc) */ |
| 935 |
rtl818x_iowrite8(priv, &priv->map->TPPOLL_STOP, |
| 936 |
RTL818x_TPPOLL_STOP_MG | RTL818x_TPPOLL_STOP_HI); |
| 937 |
|
| 938 |
rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0x00); |
| 939 |
rtl818x_iowrite16(priv, &priv->map->TID_AC_MAP, 0xFA50); |
| 940 |
|
| 941 |
rtl818x_iowrite16(priv, &priv->map->INT_MIG, 0); |
| 942 |
|
| 943 |
/* some black magic here.. */ |
| 944 |
rtl8187se_mac_config(dev); |
| 945 |
|
| 946 |
rtl818x_iowrite16(priv, RFSW_CTRL, 0x569A); |
| 947 |
rtl818x_ioread16(priv, RFSW_CTRL); |
| 948 |
|
| 949 |
rtl8180_set_anaparam(priv, RTL8225SE_ANAPARAM_ON); |
| 950 |
rtl8180_set_anaparam2(priv, RTL8225SE_ANAPARAM2_ON); |
| 951 |
rtl8180_set_anaparam3(priv, RTL8225SE_ANAPARAM3); |
| 952 |
|
| 953 |
|
| 954 |
rtl818x_iowrite8(priv, &priv->map->CONFIG5, |
| 955 |
rtl818x_ioread8(priv, &priv->map->CONFIG5) & 0x7F); |
| 956 |
|
| 957 |
/*probably this switch led on */ |
| 958 |
rtl818x_iowrite8(priv, &priv->map->PGSELECT, |
| 959 |
rtl818x_ioread8(priv, &priv->map->PGSELECT) | 0x08); |
| 960 |
|
| 961 |
rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480); |
| 962 |
rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1BFF); |
| 963 |
rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x2488); |
| 964 |
|
| 965 |
rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x4003); |
| 966 |
|
| 967 |
/* the reference code mac hardcode table write |
| 968 |
* this reg by doing byte-wide accesses. |
| 969 |
* It does it just for lowest and highest byte.. |
| 970 |
*/ |
| 971 |
reg32 = rtl818x_ioread32(priv, &priv->map->RF_PARA); |
| 972 |
reg32 &= 0x00ffff00; |
| 973 |
reg32 |= 0xb8000054; |
| 974 |
rtl818x_iowrite32(priv, &priv->map->RF_PARA, reg32); |
| 975 |
} else |
| 976 |
/* stop unused queus (no dma alloc) */ |
| 977 |
rtl818x_iowrite8(priv, &priv->map->TX_DMA_POLLING, |
| 978 |
(1<<1) | (1<<2)); |
| 979 |
|
| 980 |
priv->rf->init(dev); |
| 981 |
|
| 982 |
/* default basic rates are 1,2 Mbps for rtl8180. 1,2,6,9,12,18,24 Mbps |
| 983 |
* otherwise. bitmask 0x3 and 0x01f3 respectively. |
| 984 |
* NOTE: currenty rtl8225 RF code changes basic rates, so we need to do |
| 985 |
* this after rf init. |
| 986 |
* TODO: try to find out whether RF code really needs to do this.. |
| 987 |
*/ |
| 988 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) |
| 989 |
rtl8180_conf_basic_rates(dev, 0x3); |
| 990 |
else |
| 991 |
rtl8180_conf_basic_rates(dev, 0x1f3); |
| 992 |
|
| 993 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 994 |
rtl8187se_set_antenna_config(dev, |
| 995 |
priv->antenna_diversity_default, |
| 996 |
priv->antenna_diversity_en); |
| 997 |
return 0; |
| 998 |
} |
| 999 |
|
| 1000 |
static int rtl8180_init_rx_ring(struct ieee80211_hw *dev) |
| 1001 |
{ |
| 1002 |
struct rtl8180_priv *priv = dev->priv; |
| 1003 |
struct rtl818x_rx_cmd_desc *entry; |
| 1004 |
int i; |
| 1005 |
|
| 1006 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 1007 |
priv->rx_ring_sz = sizeof(struct rtl8187se_rx_desc); |
| 1008 |
else |
| 1009 |
priv->rx_ring_sz = sizeof(struct rtl8180_rx_desc); |
| 1010 |
|
| 1011 |
priv->rx_ring = dma_alloc_coherent(&priv->pdev->dev, |
| 1012 |
priv->rx_ring_sz * 32, |
| 1013 |
&priv->rx_ring_dma, GFP_KERNEL); |
| 1014 |
if (!priv->rx_ring || (unsigned long)priv->rx_ring & 0xFF) { |
| 1015 |
wiphy_err(dev->wiphy, "Cannot allocate RX ring\n"); |
| 1016 |
return -ENOMEM; |
| 1017 |
} |
| 1018 |
|
| 1019 |
priv->rx_idx = 0; |
| 1020 |
|
| 1021 |
for (i = 0; i < 32; i++) { |
| 1022 |
struct sk_buff *skb = dev_alloc_skb(MAX_RX_SIZE); |
| 1023 |
dma_addr_t *mapping; |
| 1024 |
entry = priv->rx_ring + priv->rx_ring_sz*i; |
| 1025 |
if (!skb) { |
| 1026 |
wiphy_err(dev->wiphy, "Cannot allocate RX skb\n"); |
| 1027 |
return -ENOMEM; |
| 1028 |
} |
| 1029 |
priv->rx_buf[i] = skb; |
| 1030 |
mapping = (dma_addr_t *)skb->cb; |
| 1031 |
*mapping = dma_map_single(&priv->pdev->dev, |
| 1032 |
skb_tail_pointer(skb), MAX_RX_SIZE, |
| 1033 |
DMA_FROM_DEVICE); |
| 1034 |
|
| 1035 |
if (dma_mapping_error(&priv->pdev->dev, *mapping)) { |
| 1036 |
kfree_skb(skb); |
| 1037 |
priv->rx_buf[i] = NULL; |
| 1038 |
wiphy_err(dev->wiphy, "Cannot map DMA for RX skb\n"); |
| 1039 |
return -ENOMEM; |
| 1040 |
} |
| 1041 |
|
| 1042 |
entry->rx_buf = cpu_to_le32(*mapping); |
| 1043 |
entry->flags = cpu_to_le32(RTL818X_RX_DESC_FLAG_OWN | |
| 1044 |
MAX_RX_SIZE); |
| 1045 |
} |
| 1046 |
entry->flags |= cpu_to_le32(RTL818X_RX_DESC_FLAG_EOR); |
| 1047 |
return 0; |
| 1048 |
} |
| 1049 |
|
| 1050 |
static void rtl8180_free_rx_ring(struct ieee80211_hw *dev) |
| 1051 |
{ |
| 1052 |
struct rtl8180_priv *priv = dev->priv; |
| 1053 |
int i; |
| 1054 |
|
| 1055 |
for (i = 0; i < 32; i++) { |
| 1056 |
struct sk_buff *skb = priv->rx_buf[i]; |
| 1057 |
if (!skb) |
| 1058 |
continue; |
| 1059 |
|
| 1060 |
dma_unmap_single(&priv->pdev->dev, *((dma_addr_t *)skb->cb), |
| 1061 |
MAX_RX_SIZE, DMA_FROM_DEVICE); |
| 1062 |
kfree_skb(skb); |
| 1063 |
} |
| 1064 |
|
| 1065 |
dma_free_coherent(&priv->pdev->dev, priv->rx_ring_sz * 32, |
| 1066 |
priv->rx_ring, priv->rx_ring_dma); |
| 1067 |
priv->rx_ring = NULL; |
| 1068 |
} |
| 1069 |
|
| 1070 |
static int rtl8180_init_tx_ring(struct ieee80211_hw *dev, |
| 1071 |
unsigned int prio, unsigned int entries) |
| 1072 |
{ |
| 1073 |
struct rtl8180_priv *priv = dev->priv; |
| 1074 |
struct rtl8180_tx_desc *ring; |
| 1075 |
dma_addr_t dma; |
| 1076 |
int i; |
| 1077 |
|
| 1078 |
ring = dma_alloc_coherent(&priv->pdev->dev, sizeof(*ring) * entries, |
| 1079 |
&dma, GFP_KERNEL); |
| 1080 |
if (!ring || (unsigned long)ring & 0xFF) { |
| 1081 |
wiphy_err(dev->wiphy, "Cannot allocate TX ring (prio = %d)\n", |
| 1082 |
prio); |
| 1083 |
return -ENOMEM; |
| 1084 |
} |
| 1085 |
|
| 1086 |
priv->tx_ring[prio].desc = ring; |
| 1087 |
priv->tx_ring[prio].dma = dma; |
| 1088 |
priv->tx_ring[prio].idx = 0; |
| 1089 |
priv->tx_ring[prio].entries = entries; |
| 1090 |
skb_queue_head_init(&priv->tx_ring[prio].queue); |
| 1091 |
|
| 1092 |
for (i = 0; i < entries; i++) |
| 1093 |
ring[i].next_tx_desc = |
| 1094 |
cpu_to_le32((u32)dma + ((i + 1) % entries) * sizeof(*ring)); |
| 1095 |
|
| 1096 |
return 0; |
| 1097 |
} |
| 1098 |
|
| 1099 |
static void rtl8180_free_tx_ring(struct ieee80211_hw *dev, unsigned int prio) |
| 1100 |
{ |
| 1101 |
struct rtl8180_priv *priv = dev->priv; |
| 1102 |
struct rtl8180_tx_ring *ring = &priv->tx_ring[prio]; |
| 1103 |
|
| 1104 |
while (skb_queue_len(&ring->queue)) { |
| 1105 |
struct rtl8180_tx_desc *entry = &ring->desc[ring->idx]; |
| 1106 |
struct sk_buff *skb = __skb_dequeue(&ring->queue); |
| 1107 |
|
| 1108 |
dma_unmap_single(&priv->pdev->dev, le32_to_cpu(entry->tx_buf), |
| 1109 |
skb->len, DMA_TO_DEVICE); |
| 1110 |
kfree_skb(skb); |
| 1111 |
ring->idx = (ring->idx + 1) % ring->entries; |
| 1112 |
} |
| 1113 |
|
| 1114 |
dma_free_coherent(&priv->pdev->dev, |
| 1115 |
sizeof(*ring->desc) * ring->entries, ring->desc, |
| 1116 |
ring->dma); |
| 1117 |
ring->desc = NULL; |
| 1118 |
} |
| 1119 |
|
| 1120 |
static int rtl8180_start(struct ieee80211_hw *dev) |
| 1121 |
{ |
| 1122 |
struct rtl8180_priv *priv = dev->priv; |
| 1123 |
int ret, i; |
| 1124 |
u32 reg; |
| 1125 |
|
| 1126 |
ret = rtl8180_init_rx_ring(dev); |
| 1127 |
if (ret) |
| 1128 |
goto err_free_rings; |
| 1129 |
|
| 1130 |
for (i = 0; i < (dev->queues + 1); i++) |
| 1131 |
if ((ret = rtl8180_init_tx_ring(dev, i, 16))) |
| 1132 |
goto err_free_rings; |
| 1133 |
|
| 1134 |
ret = rtl8180_init_hw(dev); |
| 1135 |
if (ret) |
| 1136 |
goto err_free_rings; |
| 1137 |
|
| 1138 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 1139 |
ret = request_irq(priv->pdev->irq, rtl8187se_interrupt, |
| 1140 |
IRQF_SHARED, KBUILD_MODNAME, dev); |
| 1141 |
} else { |
| 1142 |
ret = request_irq(priv->pdev->irq, rtl8180_interrupt, |
| 1143 |
IRQF_SHARED, KBUILD_MODNAME, dev); |
| 1144 |
} |
| 1145 |
|
| 1146 |
if (ret) { |
| 1147 |
wiphy_err(dev->wiphy, "failed to register IRQ handler\n"); |
| 1148 |
goto err_free_rings; |
| 1149 |
} |
| 1150 |
|
| 1151 |
rtl8180_int_enable(dev); |
| 1152 |
|
| 1153 |
/* in rtl8187se at MAR regs offset there is the management |
| 1154 |
* TX descriptor DMA addres.. |
| 1155 |
*/ |
| 1156 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 1157 |
rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0); |
| 1158 |
rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0); |
| 1159 |
} |
| 1160 |
|
| 1161 |
reg = RTL818X_RX_CONF_ONLYERLPKT | |
| 1162 |
RTL818X_RX_CONF_RX_AUTORESETPHY | |
| 1163 |
RTL818X_RX_CONF_MGMT | |
| 1164 |
RTL818X_RX_CONF_DATA | |
| 1165 |
(7 << 8 /* MAX RX DMA */) | |
| 1166 |
RTL818X_RX_CONF_BROADCAST | |
| 1167 |
RTL818X_RX_CONF_NICMAC; |
| 1168 |
|
| 1169 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185) |
| 1170 |
reg |= RTL818X_RX_CONF_CSDM1 | RTL818X_RX_CONF_CSDM2; |
| 1171 |
else if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) { |
| 1172 |
reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE1) |
| 1173 |
? RTL818X_RX_CONF_CSDM1 : 0; |
| 1174 |
reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE2) |
| 1175 |
? RTL818X_RX_CONF_CSDM2 : 0; |
| 1176 |
} else { |
| 1177 |
reg &= ~(RTL818X_RX_CONF_CSDM1 | RTL818X_RX_CONF_CSDM2); |
| 1178 |
} |
| 1179 |
|
| 1180 |
priv->rx_conf = reg; |
| 1181 |
rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg); |
| 1182 |
|
| 1183 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { |
| 1184 |
reg = rtl818x_ioread8(priv, &priv->map->CW_CONF); |
| 1185 |
|
| 1186 |
/* CW is not on per-packet basis. |
| 1187 |
* in rtl8185 the CW_VALUE reg is used. |
| 1188 |
* in rtl8187se the AC param regs are used. |
| 1189 |
*/ |
| 1190 |
reg &= ~RTL818X_CW_CONF_PERPACKET_CW; |
| 1191 |
/* retry limit IS on per-packet basis. |
| 1192 |
* the short and long retry limit in TX_CONF |
| 1193 |
* reg are ignored |
| 1194 |
*/ |
| 1195 |
reg |= RTL818X_CW_CONF_PERPACKET_RETRY; |
| 1196 |
rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg); |
| 1197 |
|
| 1198 |
reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL); |
| 1199 |
/* TX antenna and TX gain are not on per-packet basis. |
| 1200 |
* TX Antenna is selected by ANTSEL reg (RX in BB regs). |
| 1201 |
* TX gain is selected with CCK_TX_AGC and OFDM_TX_AGC regs |
| 1202 |
*/ |
| 1203 |
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN; |
| 1204 |
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL; |
| 1205 |
reg |= RTL818X_TX_AGC_CTL_FEEDBACK_ANT; |
| 1206 |
rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg); |
| 1207 |
|
| 1208 |
/* disable early TX */ |
| 1209 |
rtl818x_iowrite8(priv, (u8 __iomem *)priv->map + 0xec, 0x3f); |
| 1210 |
} |
| 1211 |
|
| 1212 |
reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); |
| 1213 |
reg |= (6 << 21 /* MAX TX DMA */) | |
| 1214 |
RTL818X_TX_CONF_NO_ICV; |
| 1215 |
|
| 1216 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 1217 |
reg |= 1<<30; /* "duration procedure mode" */ |
| 1218 |
|
| 1219 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) |
| 1220 |
reg &= ~RTL818X_TX_CONF_PROBE_DTS; |
| 1221 |
else |
| 1222 |
reg &= ~RTL818X_TX_CONF_HW_SEQNUM; |
| 1223 |
|
| 1224 |
reg &= ~RTL818X_TX_CONF_DISCW; |
| 1225 |
|
| 1226 |
/* different meaning, same value on both rtl8185 and rtl8180 */ |
| 1227 |
reg &= ~RTL818X_TX_CONF_SAT_HWPLCP; |
| 1228 |
|
| 1229 |
rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); |
| 1230 |
|
| 1231 |
reg = rtl818x_ioread8(priv, &priv->map->CMD); |
| 1232 |
reg |= RTL818X_CMD_RX_ENABLE; |
| 1233 |
reg |= RTL818X_CMD_TX_ENABLE; |
| 1234 |
rtl818x_iowrite8(priv, &priv->map->CMD, reg); |
| 1235 |
|
| 1236 |
return 0; |
| 1237 |
|
| 1238 |
err_free_rings: |
| 1239 |
rtl8180_free_rx_ring(dev); |
| 1240 |
for (i = 0; i < (dev->queues + 1); i++) |
| 1241 |
if (priv->tx_ring[i].desc) |
| 1242 |
rtl8180_free_tx_ring(dev, i); |
| 1243 |
|
| 1244 |
return ret; |
| 1245 |
} |
| 1246 |
|
| 1247 |
static void rtl8180_stop(struct ieee80211_hw *dev, bool suspend) |
| 1248 |
{ |
| 1249 |
struct rtl8180_priv *priv = dev->priv; |
| 1250 |
u8 reg; |
| 1251 |
int i; |
| 1252 |
|
| 1253 |
rtl8180_int_disable(dev); |
| 1254 |
|
| 1255 |
reg = rtl818x_ioread8(priv, &priv->map->CMD); |
| 1256 |
reg &= ~RTL818X_CMD_TX_ENABLE; |
| 1257 |
reg &= ~RTL818X_CMD_RX_ENABLE; |
| 1258 |
rtl818x_iowrite8(priv, &priv->map->CMD, reg); |
| 1259 |
|
| 1260 |
priv->rf->stop(dev); |
| 1261 |
|
| 1262 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 1263 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG4); |
| 1264 |
rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF); |
| 1265 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 1266 |
|
| 1267 |
free_irq(priv->pdev->irq, dev); |
| 1268 |
|
| 1269 |
rtl8180_free_rx_ring(dev); |
| 1270 |
for (i = 0; i < (dev->queues + 1); i++) |
| 1271 |
rtl8180_free_tx_ring(dev, i); |
| 1272 |
} |
| 1273 |
|
| 1274 |
static u64 rtl8180_get_tsf(struct ieee80211_hw *dev, |
| 1275 |
struct ieee80211_vif *vif) |
| 1276 |
{ |
| 1277 |
struct rtl8180_priv *priv = dev->priv; |
| 1278 |
|
| 1279 |
return rtl818x_ioread32(priv, &priv->map->TSFT[0]) | |
| 1280 |
(u64)(rtl818x_ioread32(priv, &priv->map->TSFT[1])) << 32; |
| 1281 |
} |
| 1282 |
|
| 1283 |
static void rtl8180_beacon_work(struct work_struct *work) |
| 1284 |
{ |
| 1285 |
struct rtl8180_vif *vif_priv = |
| 1286 |
container_of(work, struct rtl8180_vif, beacon_work.work); |
| 1287 |
struct ieee80211_vif *vif = |
| 1288 |
container_of((void *)vif_priv, struct ieee80211_vif, drv_priv); |
| 1289 |
struct ieee80211_hw *dev = vif_priv->dev; |
| 1290 |
struct ieee80211_mgmt *mgmt; |
| 1291 |
struct sk_buff *skb; |
| 1292 |
|
| 1293 |
/* don't overflow the tx ring */ |
| 1294 |
if (ieee80211_queue_stopped(dev, 0)) |
| 1295 |
goto resched; |
| 1296 |
|
| 1297 |
/* grab a fresh beacon */ |
| 1298 |
skb = ieee80211_beacon_get(dev, vif, 0); |
| 1299 |
if (!skb) |
| 1300 |
goto resched; |
| 1301 |
|
| 1302 |
/* |
| 1303 |
* update beacon timestamp w/ TSF value |
| 1304 |
* TODO: make hardware update beacon timestamp |
| 1305 |
*/ |
| 1306 |
mgmt = (struct ieee80211_mgmt *)skb->data; |
| 1307 |
mgmt->u.beacon.timestamp = cpu_to_le64(rtl8180_get_tsf(dev, vif)); |
| 1308 |
|
| 1309 |
/* TODO: use actual beacon queue */ |
| 1310 |
skb_set_queue_mapping(skb, 0); |
| 1311 |
|
| 1312 |
rtl8180_tx(dev, NULL, skb); |
| 1313 |
|
| 1314 |
resched: |
| 1315 |
/* |
| 1316 |
* schedule next beacon |
| 1317 |
* TODO: use hardware support for beacon timing |
| 1318 |
*/ |
| 1319 |
schedule_delayed_work(&vif_priv->beacon_work, |
| 1320 |
usecs_to_jiffies(1024 * vif->bss_conf.beacon_int)); |
| 1321 |
} |
| 1322 |
|
| 1323 |
static int rtl8180_add_interface(struct ieee80211_hw *dev, |
| 1324 |
struct ieee80211_vif *vif) |
| 1325 |
{ |
| 1326 |
struct rtl8180_priv *priv = dev->priv; |
| 1327 |
struct rtl8180_vif *vif_priv; |
| 1328 |
|
| 1329 |
/* |
| 1330 |
* We only support one active interface at a time. |
| 1331 |
*/ |
| 1332 |
if (priv->vif) |
| 1333 |
return -EBUSY; |
| 1334 |
|
| 1335 |
switch (vif->type) { |
| 1336 |
case NL80211_IFTYPE_STATION: |
| 1337 |
case NL80211_IFTYPE_ADHOC: |
| 1338 |
break; |
| 1339 |
default: |
| 1340 |
return -EOPNOTSUPP; |
| 1341 |
} |
| 1342 |
|
| 1343 |
priv->vif = vif; |
| 1344 |
|
| 1345 |
/* Initialize driver private area */ |
| 1346 |
vif_priv = (struct rtl8180_vif *)&vif->drv_priv; |
| 1347 |
vif_priv->dev = dev; |
| 1348 |
INIT_DELAYED_WORK(&vif_priv->beacon_work, rtl8180_beacon_work); |
| 1349 |
vif_priv->enable_beacon = false; |
| 1350 |
|
| 1351 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 1352 |
rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->MAC[0], |
| 1353 |
le32_to_cpu(*(__le32 *)vif->addr)); |
| 1354 |
rtl818x_iowrite16(priv, (__le16 __iomem *)&priv->map->MAC[4], |
| 1355 |
le16_to_cpu(*(__le16 *)(vif->addr + 4))); |
| 1356 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 1357 |
|
| 1358 |
return 0; |
| 1359 |
} |
| 1360 |
|
| 1361 |
static void rtl8180_remove_interface(struct ieee80211_hw *dev, |
| 1362 |
struct ieee80211_vif *vif) |
| 1363 |
{ |
| 1364 |
struct rtl8180_priv *priv = dev->priv; |
| 1365 |
priv->vif = NULL; |
| 1366 |
} |
| 1367 |
|
| 1368 |
static int rtl8180_config(struct ieee80211_hw *dev, int radio_idx, u32 changed) |
| 1369 |
{ |
| 1370 |
struct rtl8180_priv *priv = dev->priv; |
| 1371 |
struct ieee80211_conf *conf = &dev->conf; |
| 1372 |
|
| 1373 |
priv->rf->set_chan(dev, conf); |
| 1374 |
|
| 1375 |
return 0; |
| 1376 |
} |
| 1377 |
|
| 1378 |
static void rtl8187se_conf_ac_parm(struct ieee80211_hw *dev, u8 queue) |
| 1379 |
{ |
| 1380 |
const struct ieee80211_tx_queue_params *params; |
| 1381 |
struct rtl8180_priv *priv = dev->priv; |
| 1382 |
|
| 1383 |
/* hw value */ |
| 1384 |
u32 ac_param; |
| 1385 |
|
| 1386 |
u8 aifs; |
| 1387 |
u8 txop; |
| 1388 |
u8 cw_min, cw_max; |
| 1389 |
|
| 1390 |
params = &priv->queue_param[queue]; |
| 1391 |
|
| 1392 |
cw_min = fls(params->cw_min); |
| 1393 |
cw_max = fls(params->cw_max); |
| 1394 |
|
| 1395 |
aifs = 10 + params->aifs * priv->slot_time; |
| 1396 |
|
| 1397 |
/* TODO: check if txop HW is in us (mult by 32) */ |
| 1398 |
txop = params->txop; |
| 1399 |
|
| 1400 |
ac_param = txop << AC_PARAM_TXOP_LIMIT_SHIFT | |
| 1401 |
cw_max << AC_PARAM_ECW_MAX_SHIFT | |
| 1402 |
cw_min << AC_PARAM_ECW_MIN_SHIFT | |
| 1403 |
aifs << AC_PARAM_AIFS_SHIFT; |
| 1404 |
|
| 1405 |
switch (queue) { |
| 1406 |
case IEEE80211_AC_BK: |
| 1407 |
rtl818x_iowrite32(priv, &priv->map->AC_BK_PARAM, ac_param); |
| 1408 |
break; |
| 1409 |
case IEEE80211_AC_BE: |
| 1410 |
rtl818x_iowrite32(priv, &priv->map->AC_BE_PARAM, ac_param); |
| 1411 |
break; |
| 1412 |
case IEEE80211_AC_VI: |
| 1413 |
rtl818x_iowrite32(priv, &priv->map->AC_VI_PARAM, ac_param); |
| 1414 |
break; |
| 1415 |
case IEEE80211_AC_VO: |
| 1416 |
rtl818x_iowrite32(priv, &priv->map->AC_VO_PARAM, ac_param); |
| 1417 |
break; |
| 1418 |
} |
| 1419 |
} |
| 1420 |
|
| 1421 |
static int rtl8180_conf_tx(struct ieee80211_hw *dev, |
| 1422 |
struct ieee80211_vif *vif, |
| 1423 |
unsigned int link_id, u16 queue, |
| 1424 |
const struct ieee80211_tx_queue_params *params) |
| 1425 |
{ |
| 1426 |
struct rtl8180_priv *priv = dev->priv; |
| 1427 |
u8 cw_min, cw_max; |
| 1428 |
|
| 1429 |
/* nothing to do ? */ |
| 1430 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) |
| 1431 |
return 0; |
| 1432 |
|
| 1433 |
cw_min = fls(params->cw_min); |
| 1434 |
cw_max = fls(params->cw_max); |
| 1435 |
|
| 1436 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 1437 |
priv->queue_param[queue] = *params; |
| 1438 |
rtl8187se_conf_ac_parm(dev, queue); |
| 1439 |
} else |
| 1440 |
rtl818x_iowrite8(priv, &priv->map->CW_VAL, |
| 1441 |
(cw_max << 4) | cw_min); |
| 1442 |
return 0; |
| 1443 |
} |
| 1444 |
|
| 1445 |
static void rtl8180_conf_erp(struct ieee80211_hw *dev, |
| 1446 |
struct ieee80211_bss_conf *info) |
| 1447 |
{ |
| 1448 |
struct rtl8180_priv *priv = dev->priv; |
| 1449 |
u8 sifs, difs; |
| 1450 |
int eifs; |
| 1451 |
u8 hw_eifs; |
| 1452 |
|
| 1453 |
/* TODO: should we do something ? */ |
| 1454 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) |
| 1455 |
return; |
| 1456 |
|
| 1457 |
/* I _hope_ this means 10uS for the HW. |
| 1458 |
* In reference code it is 0x22 for |
| 1459 |
* both rtl8187L and rtl8187SE |
| 1460 |
*/ |
| 1461 |
sifs = 0x22; |
| 1462 |
|
| 1463 |
if (info->use_short_slot) |
| 1464 |
priv->slot_time = 9; |
| 1465 |
else |
| 1466 |
priv->slot_time = 20; |
| 1467 |
|
| 1468 |
/* 10 is SIFS time in uS */ |
| 1469 |
difs = 10 + 2 * priv->slot_time; |
| 1470 |
eifs = 10 + difs + priv->ack_time; |
| 1471 |
|
| 1472 |
/* HW should use 4uS units for EIFS (I'm sure for rtl8185)*/ |
| 1473 |
hw_eifs = DIV_ROUND_UP(eifs, 4); |
| 1474 |
|
| 1475 |
|
| 1476 |
rtl818x_iowrite8(priv, &priv->map->SLOT, priv->slot_time); |
| 1477 |
rtl818x_iowrite8(priv, &priv->map->SIFS, sifs); |
| 1478 |
rtl818x_iowrite8(priv, &priv->map->DIFS, difs); |
| 1479 |
|
| 1480 |
/* from reference code. set ack timeout reg = eifs reg */ |
| 1481 |
rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER, hw_eifs); |
| 1482 |
|
| 1483 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 1484 |
rtl818x_iowrite8(priv, &priv->map->EIFS_8187SE, hw_eifs); |
| 1485 |
else if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8185) { |
| 1486 |
/* rtl8187/rtl8185 HW bug. After EIFS is elapsed, |
| 1487 |
* the HW still wait for DIFS. |
| 1488 |
* HW uses 4uS units for EIFS. |
| 1489 |
*/ |
| 1490 |
hw_eifs = DIV_ROUND_UP(eifs - difs, 4); |
| 1491 |
|
| 1492 |
rtl818x_iowrite8(priv, &priv->map->EIFS, hw_eifs); |
| 1493 |
} |
| 1494 |
} |
| 1495 |
|
| 1496 |
static void rtl8180_bss_info_changed(struct ieee80211_hw *dev, |
| 1497 |
struct ieee80211_vif *vif, |
| 1498 |
struct ieee80211_bss_conf *info, |
| 1499 |
u64 changed) |
| 1500 |
{ |
| 1501 |
struct rtl8180_priv *priv = dev->priv; |
| 1502 |
struct rtl8180_vif *vif_priv; |
| 1503 |
int i; |
| 1504 |
u8 reg; |
| 1505 |
|
| 1506 |
vif_priv = (struct rtl8180_vif *)&vif->drv_priv; |
| 1507 |
|
| 1508 |
if (changed & BSS_CHANGED_BSSID) { |
| 1509 |
rtl818x_iowrite16(priv, (__le16 __iomem *)&priv->map->BSSID[0], |
| 1510 |
le16_to_cpu(*(__le16 *)info->bssid)); |
| 1511 |
rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->BSSID[2], |
| 1512 |
le32_to_cpu(*(__le32 *)(info->bssid + 2))); |
| 1513 |
|
| 1514 |
if (is_valid_ether_addr(info->bssid)) { |
| 1515 |
if (vif->type == NL80211_IFTYPE_ADHOC) |
| 1516 |
reg = RTL818X_MSR_ADHOC; |
| 1517 |
else |
| 1518 |
reg = RTL818X_MSR_INFRA; |
| 1519 |
} else |
| 1520 |
reg = RTL818X_MSR_NO_LINK; |
| 1521 |
|
| 1522 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 1523 |
reg |= RTL818X_MSR_ENEDCA; |
| 1524 |
|
| 1525 |
rtl818x_iowrite8(priv, &priv->map->MSR, reg); |
| 1526 |
} |
| 1527 |
|
| 1528 |
if (changed & BSS_CHANGED_BASIC_RATES) |
| 1529 |
rtl8180_conf_basic_rates(dev, info->basic_rates); |
| 1530 |
|
| 1531 |
if (changed & (BSS_CHANGED_ERP_SLOT | BSS_CHANGED_ERP_PREAMBLE)) { |
| 1532 |
|
| 1533 |
/* when preamble changes, acktime duration changes, and erp must |
| 1534 |
* be recalculated. ACK time is calculated at lowest rate. |
| 1535 |
* Since mac80211 include SIFS time we remove it (-10) |
| 1536 |
*/ |
| 1537 |
priv->ack_time = |
| 1538 |
le16_to_cpu(ieee80211_generic_frame_duration(dev, |
| 1539 |
priv->vif, |
| 1540 |
NL80211_BAND_2GHZ, 10, |
| 1541 |
&priv->rates[0])) - 10; |
| 1542 |
|
| 1543 |
rtl8180_conf_erp(dev, info); |
| 1544 |
|
| 1545 |
/* mac80211 supplies aifs_n to driver and calls |
| 1546 |
* conf_tx callback whether aifs_n changes, NOT |
| 1547 |
* when aifs changes. |
| 1548 |
* Aifs should be recalculated if slot changes. |
| 1549 |
*/ |
| 1550 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 1551 |
for (i = 0; i < 4; i++) |
| 1552 |
rtl8187se_conf_ac_parm(dev, i); |
| 1553 |
} |
| 1554 |
} |
| 1555 |
|
| 1556 |
if (changed & BSS_CHANGED_BEACON_ENABLED) |
| 1557 |
vif_priv->enable_beacon = info->enable_beacon; |
| 1558 |
|
| 1559 |
if (changed & (BSS_CHANGED_BEACON_ENABLED | BSS_CHANGED_BEACON)) { |
| 1560 |
cancel_delayed_work_sync(&vif_priv->beacon_work); |
| 1561 |
if (vif_priv->enable_beacon) |
| 1562 |
schedule_work(&vif_priv->beacon_work.work); |
| 1563 |
} |
| 1564 |
} |
| 1565 |
|
| 1566 |
static u64 rtl8180_prepare_multicast(struct ieee80211_hw *dev, |
| 1567 |
struct netdev_hw_addr_list *mc_list) |
| 1568 |
{ |
| 1569 |
return netdev_hw_addr_list_count(mc_list); |
| 1570 |
} |
| 1571 |
|
| 1572 |
static void rtl8180_configure_filter(struct ieee80211_hw *dev, |
| 1573 |
unsigned int changed_flags, |
| 1574 |
unsigned int *total_flags, |
| 1575 |
u64 multicast) |
| 1576 |
{ |
| 1577 |
struct rtl8180_priv *priv = dev->priv; |
| 1578 |
|
| 1579 |
if (changed_flags & FIF_FCSFAIL) |
| 1580 |
priv->rx_conf ^= RTL818X_RX_CONF_FCS; |
| 1581 |
if (changed_flags & FIF_CONTROL) |
| 1582 |
priv->rx_conf ^= RTL818X_RX_CONF_CTRL; |
| 1583 |
if (changed_flags & FIF_OTHER_BSS) |
| 1584 |
priv->rx_conf ^= RTL818X_RX_CONF_MONITOR; |
| 1585 |
if (*total_flags & FIF_ALLMULTI || multicast > 0) |
| 1586 |
priv->rx_conf |= RTL818X_RX_CONF_MULTICAST; |
| 1587 |
else |
| 1588 |
priv->rx_conf &= ~RTL818X_RX_CONF_MULTICAST; |
| 1589 |
|
| 1590 |
*total_flags = 0; |
| 1591 |
|
| 1592 |
if (priv->rx_conf & RTL818X_RX_CONF_FCS) |
| 1593 |
*total_flags |= FIF_FCSFAIL; |
| 1594 |
if (priv->rx_conf & RTL818X_RX_CONF_CTRL) |
| 1595 |
*total_flags |= FIF_CONTROL; |
| 1596 |
if (priv->rx_conf & RTL818X_RX_CONF_MONITOR) |
| 1597 |
*total_flags |= FIF_OTHER_BSS; |
| 1598 |
if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST) |
| 1599 |
*total_flags |= FIF_ALLMULTI; |
| 1600 |
|
| 1601 |
rtl818x_iowrite32(priv, &priv->map->RX_CONF, priv->rx_conf); |
| 1602 |
} |
| 1603 |
|
| 1604 |
static const struct ieee80211_ops rtl8180_ops = { |
| 1605 |
.add_chanctx = ieee80211_emulate_add_chanctx, |
| 1606 |
.remove_chanctx = ieee80211_emulate_remove_chanctx, |
| 1607 |
.change_chanctx = ieee80211_emulate_change_chanctx, |
| 1608 |
.switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx, |
| 1609 |
.tx = rtl8180_tx, |
| 1610 |
.wake_tx_queue = ieee80211_handle_wake_tx_queue, |
| 1611 |
.start = rtl8180_start, |
| 1612 |
.stop = rtl8180_stop, |
| 1613 |
.add_interface = rtl8180_add_interface, |
| 1614 |
.remove_interface = rtl8180_remove_interface, |
| 1615 |
.config = rtl8180_config, |
| 1616 |
.bss_info_changed = rtl8180_bss_info_changed, |
| 1617 |
.conf_tx = rtl8180_conf_tx, |
| 1618 |
.prepare_multicast = rtl8180_prepare_multicast, |
| 1619 |
.configure_filter = rtl8180_configure_filter, |
| 1620 |
.get_tsf = rtl8180_get_tsf, |
| 1621 |
}; |
| 1622 |
|
| 1623 |
static void rtl8180_eeprom_register_read(struct eeprom_93cx6 *eeprom) |
| 1624 |
{ |
| 1625 |
struct rtl8180_priv *priv = eeprom->data; |
| 1626 |
u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); |
| 1627 |
|
| 1628 |
eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE; |
| 1629 |
eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ; |
| 1630 |
eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK; |
| 1631 |
eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS; |
| 1632 |
} |
| 1633 |
|
| 1634 |
static void rtl8180_eeprom_register_write(struct eeprom_93cx6 *eeprom) |
| 1635 |
{ |
| 1636 |
struct rtl8180_priv *priv = eeprom->data; |
| 1637 |
u8 reg = 2 << 6; |
| 1638 |
|
| 1639 |
if (eeprom->reg_data_in) |
| 1640 |
reg |= RTL818X_EEPROM_CMD_WRITE; |
| 1641 |
if (eeprom->reg_data_out) |
| 1642 |
reg |= RTL818X_EEPROM_CMD_READ; |
| 1643 |
if (eeprom->reg_data_clock) |
| 1644 |
reg |= RTL818X_EEPROM_CMD_CK; |
| 1645 |
if (eeprom->reg_chip_select) |
| 1646 |
reg |= RTL818X_EEPROM_CMD_CS; |
| 1647 |
|
| 1648 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg); |
| 1649 |
rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); |
| 1650 |
udelay(10); |
| 1651 |
} |
| 1652 |
|
| 1653 |
static void rtl8180_eeprom_read(struct rtl8180_priv *priv) |
| 1654 |
{ |
| 1655 |
struct eeprom_93cx6 eeprom; |
| 1656 |
int eeprom_cck_table_adr; |
| 1657 |
u16 eeprom_val; |
| 1658 |
int i; |
| 1659 |
|
| 1660 |
eeprom.data = priv; |
| 1661 |
eeprom.register_read = rtl8180_eeprom_register_read; |
| 1662 |
eeprom.register_write = rtl8180_eeprom_register_write; |
| 1663 |
if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6)) |
| 1664 |
eeprom.width = PCI_EEPROM_WIDTH_93C66; |
| 1665 |
else |
| 1666 |
eeprom.width = PCI_EEPROM_WIDTH_93C46; |
| 1667 |
|
| 1668 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 1669 |
RTL818X_EEPROM_CMD_PROGRAM); |
| 1670 |
rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); |
| 1671 |
udelay(10); |
| 1672 |
|
| 1673 |
eeprom_93cx6_read(&eeprom, 0x06, &eeprom_val); |
| 1674 |
eeprom_val &= 0xFF; |
| 1675 |
priv->rf_type = eeprom_val; |
| 1676 |
|
| 1677 |
eeprom_93cx6_read(&eeprom, 0x17, &eeprom_val); |
| 1678 |
priv->csthreshold = eeprom_val >> 8; |
| 1679 |
|
| 1680 |
eeprom_93cx6_multiread(&eeprom, 0x7, (__le16 *)priv->mac_addr, 3); |
| 1681 |
|
| 1682 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 1683 |
eeprom_cck_table_adr = 0x30; |
| 1684 |
else |
| 1685 |
eeprom_cck_table_adr = 0x10; |
| 1686 |
|
| 1687 |
/* CCK TX power */ |
| 1688 |
for (i = 0; i < 14; i += 2) { |
| 1689 |
u16 txpwr; |
| 1690 |
eeprom_93cx6_read(&eeprom, eeprom_cck_table_adr + (i >> 1), |
| 1691 |
&txpwr); |
| 1692 |
priv->channels[i].hw_value = txpwr & 0xFF; |
| 1693 |
priv->channels[i + 1].hw_value = txpwr >> 8; |
| 1694 |
} |
| 1695 |
|
| 1696 |
/* OFDM TX power */ |
| 1697 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { |
| 1698 |
for (i = 0; i < 14; i += 2) { |
| 1699 |
u16 txpwr; |
| 1700 |
eeprom_93cx6_read(&eeprom, 0x20 + (i >> 1), &txpwr); |
| 1701 |
priv->channels[i].hw_value |= (txpwr & 0xFF) << 8; |
| 1702 |
priv->channels[i + 1].hw_value |= txpwr & 0xFF00; |
| 1703 |
} |
| 1704 |
} |
| 1705 |
|
| 1706 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8180) { |
| 1707 |
__le32 anaparam; |
| 1708 |
eeprom_93cx6_multiread(&eeprom, 0xD, (__le16 *)&anaparam, 2); |
| 1709 |
priv->anaparam = le32_to_cpu(anaparam); |
| 1710 |
eeprom_93cx6_read(&eeprom, 0x19, &priv->rfparam); |
| 1711 |
} |
| 1712 |
|
| 1713 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) { |
| 1714 |
eeprom_93cx6_read(&eeprom, 0x3F, &eeprom_val); |
| 1715 |
priv->antenna_diversity_en = !!(eeprom_val & 0x100); |
| 1716 |
priv->antenna_diversity_default = (eeprom_val & 0xC00) == 0x400; |
| 1717 |
|
| 1718 |
eeprom_93cx6_read(&eeprom, 0x7C, &eeprom_val); |
| 1719 |
priv->xtal_out = eeprom_val & 0xF; |
| 1720 |
priv->xtal_in = (eeprom_val & 0xF0) >> 4; |
| 1721 |
priv->xtal_cal = !!(eeprom_val & 0x1000); |
| 1722 |
priv->thermal_meter_val = (eeprom_val & 0xF00) >> 8; |
| 1723 |
priv->thermal_meter_en = !!(eeprom_val & 0x2000); |
| 1724 |
} |
| 1725 |
|
| 1726 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 1727 |
RTL818X_EEPROM_CMD_NORMAL); |
| 1728 |
} |
| 1729 |
|
| 1730 |
static int rtl8180_probe(struct pci_dev *pdev, |
| 1731 |
const struct pci_device_id *id) |
| 1732 |
{ |
| 1733 |
struct ieee80211_hw *dev; |
| 1734 |
struct rtl8180_priv *priv; |
| 1735 |
unsigned long mem_len; |
| 1736 |
unsigned int io_len; |
| 1737 |
int err; |
| 1738 |
const char *chip_name, *rf_name = NULL; |
| 1739 |
u32 reg; |
| 1740 |
|
| 1741 |
err = pci_enable_device(pdev); |
| 1742 |
if (err) { |
| 1743 |
printk(KERN_ERR "%s (rtl8180): Cannot enable new PCI device\n", |
| 1744 |
pci_name(pdev)); |
| 1745 |
return err; |
| 1746 |
} |
| 1747 |
|
| 1748 |
err = pci_request_regions(pdev, KBUILD_MODNAME); |
| 1749 |
if (err) { |
| 1750 |
printk(KERN_ERR "%s (rtl8180): Cannot obtain PCI resources\n", |
| 1751 |
pci_name(pdev)); |
| 1752 |
goto err_disable_dev; |
| 1753 |
} |
| 1754 |
|
| 1755 |
io_len = pci_resource_len(pdev, 0); |
| 1756 |
mem_len = pci_resource_len(pdev, 1); |
| 1757 |
|
| 1758 |
if (mem_len < sizeof(struct rtl818x_csr) || |
| 1759 |
io_len < sizeof(struct rtl818x_csr)) { |
| 1760 |
printk(KERN_ERR "%s (rtl8180): Too short PCI resources\n", |
| 1761 |
pci_name(pdev)); |
| 1762 |
err = -ENOMEM; |
| 1763 |
goto err_free_reg; |
| 1764 |
} |
| 1765 |
|
| 1766 |
if ((err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32))) || |
| 1767 |
(err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32)))) { |
| 1768 |
printk(KERN_ERR "%s (rtl8180): No suitable DMA available\n", |
| 1769 |
pci_name(pdev)); |
| 1770 |
goto err_free_reg; |
| 1771 |
} |
| 1772 |
|
| 1773 |
pci_set_master(pdev); |
| 1774 |
|
| 1775 |
dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8180_ops); |
| 1776 |
if (!dev) { |
| 1777 |
printk(KERN_ERR "%s (rtl8180): ieee80211 alloc failed\n", |
| 1778 |
pci_name(pdev)); |
| 1779 |
err = -ENOMEM; |
| 1780 |
goto err_free_reg; |
| 1781 |
} |
| 1782 |
|
| 1783 |
priv = dev->priv; |
| 1784 |
priv->pdev = pdev; |
| 1785 |
|
| 1786 |
dev->max_rates = 1; |
| 1787 |
SET_IEEE80211_DEV(dev, &pdev->dev); |
| 1788 |
pci_set_drvdata(pdev, dev); |
| 1789 |
|
| 1790 |
priv->map_pio = false; |
| 1791 |
priv->map = pci_iomap(pdev, 1, mem_len); |
| 1792 |
if (!priv->map) { |
| 1793 |
priv->map = pci_iomap(pdev, 0, io_len); |
| 1794 |
priv->map_pio = true; |
| 1795 |
} |
| 1796 |
|
| 1797 |
if (!priv->map) { |
| 1798 |
dev_err(&pdev->dev, "Cannot map device memory/PIO\n"); |
| 1799 |
err = -ENOMEM; |
| 1800 |
goto err_free_dev; |
| 1801 |
} |
| 1802 |
|
| 1803 |
BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels)); |
| 1804 |
BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates)); |
| 1805 |
|
| 1806 |
memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels)); |
| 1807 |
memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates)); |
| 1808 |
|
| 1809 |
priv->band.band = NL80211_BAND_2GHZ; |
| 1810 |
priv->band.channels = priv->channels; |
| 1811 |
priv->band.n_channels = ARRAY_SIZE(rtl818x_channels); |
| 1812 |
priv->band.bitrates = priv->rates; |
| 1813 |
priv->band.n_bitrates = 4; |
| 1814 |
dev->wiphy->bands[NL80211_BAND_2GHZ] = &priv->band; |
| 1815 |
|
| 1816 |
ieee80211_hw_set(dev, HOST_BROADCAST_PS_BUFFERING); |
| 1817 |
ieee80211_hw_set(dev, RX_INCLUDES_FCS); |
| 1818 |
|
| 1819 |
dev->vif_data_size = sizeof(struct rtl8180_vif); |
| 1820 |
dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) | |
| 1821 |
BIT(NL80211_IFTYPE_ADHOC); |
| 1822 |
dev->max_signal = 65; |
| 1823 |
|
| 1824 |
reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); |
| 1825 |
reg &= RTL818X_TX_CONF_HWVER_MASK; |
| 1826 |
switch (reg) { |
| 1827 |
case RTL818X_TX_CONF_R8180_ABCD: |
| 1828 |
chip_name = "RTL8180"; |
| 1829 |
priv->chip_family = RTL818X_CHIP_FAMILY_RTL8180; |
| 1830 |
break; |
| 1831 |
|
| 1832 |
case RTL818X_TX_CONF_R8180_F: |
| 1833 |
chip_name = "RTL8180vF"; |
| 1834 |
priv->chip_family = RTL818X_CHIP_FAMILY_RTL8180; |
| 1835 |
break; |
| 1836 |
|
| 1837 |
case RTL818X_TX_CONF_R8185_ABC: |
| 1838 |
chip_name = "RTL8185"; |
| 1839 |
priv->chip_family = RTL818X_CHIP_FAMILY_RTL8185; |
| 1840 |
break; |
| 1841 |
|
| 1842 |
case RTL818X_TX_CONF_R8185_D: |
| 1843 |
chip_name = "RTL8185vD"; |
| 1844 |
priv->chip_family = RTL818X_CHIP_FAMILY_RTL8185; |
| 1845 |
break; |
| 1846 |
|
| 1847 |
case RTL818X_TX_CONF_RTL8187SE: |
| 1848 |
chip_name = "RTL8187SE"; |
| 1849 |
if (priv->map_pio) { |
| 1850 |
dev_err(&pdev->dev, |
| 1851 |
"MMIO failed. PIO not supported on RTL8187SE\n"); |
| 1852 |
err = -ENOMEM; |
| 1853 |
goto err_iounmap; |
| 1854 |
} |
| 1855 |
priv->chip_family = RTL818X_CHIP_FAMILY_RTL8187SE; |
| 1856 |
break; |
| 1857 |
|
| 1858 |
default: |
| 1859 |
printk(KERN_ERR "%s (rtl8180): Unknown chip! (0x%x)\n", |
| 1860 |
pci_name(pdev), reg >> 25); |
| 1861 |
err = -ENODEV; |
| 1862 |
goto err_iounmap; |
| 1863 |
} |
| 1864 |
|
| 1865 |
/* we declare to MAC80211 all the queues except for beacon queue |
| 1866 |
* that will be eventually handled by DRV. |
| 1867 |
* TX rings are arranged in such a way that lower is the IDX, |
| 1868 |
* higher is the priority, in order to achieve direct mapping |
| 1869 |
* with mac80211, however the beacon queue is an exception and it |
| 1870 |
* is mapped on the highst tx ring IDX. |
| 1871 |
*/ |
| 1872 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 1873 |
dev->queues = RTL8187SE_NR_TX_QUEUES - 1; |
| 1874 |
else |
| 1875 |
dev->queues = RTL8180_NR_TX_QUEUES - 1; |
| 1876 |
|
| 1877 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) { |
| 1878 |
priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates); |
| 1879 |
pci_try_set_mwi(pdev); |
| 1880 |
} |
| 1881 |
|
| 1882 |
if (priv->chip_family != RTL818X_CHIP_FAMILY_RTL8180) |
| 1883 |
ieee80211_hw_set(dev, SIGNAL_DBM); |
| 1884 |
else |
| 1885 |
ieee80211_hw_set(dev, SIGNAL_UNSPEC); |
| 1886 |
|
| 1887 |
wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); |
| 1888 |
|
| 1889 |
rtl8180_eeprom_read(priv); |
| 1890 |
|
| 1891 |
switch (priv->rf_type) { |
| 1892 |
case 1: rf_name = "Intersil"; |
| 1893 |
break; |
| 1894 |
case 2: rf_name = "RFMD"; |
| 1895 |
break; |
| 1896 |
case 3: priv->rf = &sa2400_rf_ops; |
| 1897 |
break; |
| 1898 |
case 4: priv->rf = &max2820_rf_ops; |
| 1899 |
break; |
| 1900 |
case 5: priv->rf = &grf5101_rf_ops; |
| 1901 |
break; |
| 1902 |
case 9: |
| 1903 |
if (priv->chip_family == RTL818X_CHIP_FAMILY_RTL8187SE) |
| 1904 |
priv->rf = rtl8187se_detect_rf(dev); |
| 1905 |
else |
| 1906 |
priv->rf = rtl8180_detect_rf(dev); |
| 1907 |
break; |
| 1908 |
case 10: |
| 1909 |
rf_name = "RTL8255"; |
| 1910 |
break; |
| 1911 |
default: |
| 1912 |
printk(KERN_ERR "%s (rtl8180): Unknown RF! (0x%x)\n", |
| 1913 |
pci_name(pdev), priv->rf_type); |
| 1914 |
err = -ENODEV; |
| 1915 |
goto err_iounmap; |
| 1916 |
} |
| 1917 |
|
| 1918 |
if (!priv->rf) { |
| 1919 |
printk(KERN_ERR "%s (rtl8180): %s RF frontend not supported!\n", |
| 1920 |
pci_name(pdev), rf_name); |
| 1921 |
err = -ENODEV; |
| 1922 |
goto err_iounmap; |
| 1923 |
} |
| 1924 |
|
| 1925 |
if (!is_valid_ether_addr(priv->mac_addr)) { |
| 1926 |
printk(KERN_WARNING "%s (rtl8180): Invalid hwaddr! Using" |
| 1927 |
" randomly generated MAC addr\n", pci_name(pdev)); |
| 1928 |
eth_random_addr(priv->mac_addr); |
| 1929 |
} |
| 1930 |
SET_IEEE80211_PERM_ADDR(dev, priv->mac_addr); |
| 1931 |
|
| 1932 |
spin_lock_init(&priv->lock); |
| 1933 |
|
| 1934 |
err = ieee80211_register_hw(dev); |
| 1935 |
if (err) { |
| 1936 |
printk(KERN_ERR "%s (rtl8180): Cannot register device\n", |
| 1937 |
pci_name(pdev)); |
| 1938 |
goto err_iounmap; |
| 1939 |
} |
| 1940 |
|
| 1941 |
wiphy_info(dev->wiphy, "hwaddr %pm, %s + %s\n", |
| 1942 |
priv->mac_addr, chip_name, priv->rf->name); |
| 1943 |
|
| 1944 |
return 0; |
| 1945 |
|
| 1946 |
err_iounmap: |
| 1947 |
pci_iounmap(pdev, priv->map); |
| 1948 |
|
| 1949 |
err_free_dev: |
| 1950 |
ieee80211_free_hw(dev); |
| 1951 |
|
| 1952 |
err_free_reg: |
| 1953 |
pci_release_regions(pdev); |
| 1954 |
|
| 1955 |
err_disable_dev: |
| 1956 |
pci_disable_device(pdev); |
| 1957 |
return err; |
| 1958 |
} |
| 1959 |
|
| 1960 |
static void rtl8180_remove(struct pci_dev *pdev) |
| 1961 |
{ |
| 1962 |
struct ieee80211_hw *dev = pci_get_drvdata(pdev); |
| 1963 |
struct rtl8180_priv *priv; |
| 1964 |
|
| 1965 |
if (!dev) |
| 1966 |
return; |
| 1967 |
|
| 1968 |
ieee80211_unregister_hw(dev); |
| 1969 |
|
| 1970 |
priv = dev->priv; |
| 1971 |
|
| 1972 |
pci_iounmap(pdev, priv->map); |
| 1973 |
pci_release_regions(pdev); |
| 1974 |
pci_disable_device(pdev); |
| 1975 |
ieee80211_free_hw(dev); |
| 1976 |
} |
| 1977 |
|
| 1978 |
#define rtl8180_suspend NULL |
| 1979 |
#define rtl8180_resume NULL |
| 1980 |
|
| 1981 |
static SIMPLE_DEV_PM_OPS(rtl8180_pm_ops, rtl8180_suspend, rtl8180_resume); |
| 1982 |
|
| 1983 |
static struct pci_driver rtl8180_driver = { |
| 1984 |
.name = KBUILD_MODNAME, |
| 1985 |
.id_table = rtl8180_table, |
| 1986 |
.probe = rtl8180_probe, |
| 1987 |
.remove = rtl8180_remove, |
| 1988 |
.driver.pm = &rtl8180_pm_ops, |
| 1989 |
}; |
| 1990 |
|
| 1991 |
module_pci_driver(rtl8180_driver); |