| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
Copyright (C) 2004 - 2009 Ivo van Doorn <[email protected]> |
| 4 |
<http://rt2x00.serialmonkey.com> |
| 5 |
|
| 6 |
*/ |
| 7 |
|
| 8 |
/* |
| 9 |
Module: rt73usb |
| 10 |
Abstract: rt73usb device specific routines. |
| 11 |
Supported chipsets: rt2571W & rt2671. |
| 12 |
*/ |
| 13 |
|
| 14 |
#include <linux/crc-itu-t.h> |
| 15 |
#include <linux/delay.h> |
| 16 |
#include <linux/etherdevice.h> |
| 17 |
#include <linux/kernel.h> |
| 18 |
#include <linux/module.h> |
| 19 |
#include <linux/slab.h> |
| 20 |
#include <linux/usb.h> |
| 21 |
|
| 22 |
#include "rt2x00.h" |
| 23 |
#include "rt2x00usb.h" |
| 24 |
#include "rt73usb.h" |
| 25 |
|
| 26 |
/* |
| 27 |
* Allow hardware encryption to be disabled. |
| 28 |
*/ |
| 29 |
static bool modparam_nohwcrypt; |
| 30 |
module_param_named(nohwcrypt, modparam_nohwcrypt, bool, 0444); |
| 31 |
MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); |
| 32 |
|
| 33 |
/* |
| 34 |
* Register access. |
| 35 |
* All access to the CSR registers will go through the methods |
| 36 |
* rt2x00usb_register_read and rt2x00usb_register_write. |
| 37 |
* BBP and RF register require indirect register access, |
| 38 |
* and use the CSR registers BBPCSR and RFCSR to achieve this. |
| 39 |
* These indirect registers work with busy bits, |
| 40 |
* and we will try maximal REGISTER_BUSY_COUNT times to access |
| 41 |
* the register while taking a REGISTER_BUSY_DELAY us delay |
| 42 |
* between each attampt. When the busy bit is still set at that time, |
| 43 |
* the access attempt is considered to have failed, |
| 44 |
* and we will print an error. |
| 45 |
* The _lock versions must be used if you already hold the csr_mutex |
| 46 |
*/ |
| 47 |
#define WAIT_FOR_BBP(__dev, __reg) \ |
| 48 |
rt2x00usb_regbusy_read((__dev), PHY_CSR3, PHY_CSR3_BUSY, (__reg)) |
| 49 |
#define WAIT_FOR_RF(__dev, __reg) \ |
| 50 |
rt2x00usb_regbusy_read((__dev), PHY_CSR4, PHY_CSR4_BUSY, (__reg)) |
| 51 |
|
| 52 |
static void rt73usb_bbp_write(struct rt2x00_dev *rt2x00dev, |
| 53 |
const unsigned int word, const u8 value) |
| 54 |
{ |
| 55 |
u32 reg; |
| 56 |
|
| 57 |
mutex_lock(&rt2x00dev->csr_mutex); |
| 58 |
|
| 59 |
/* |
| 60 |
* Wait until the BBP becomes available, afterwards we |
| 61 |
* can safely write the new data into the register. |
| 62 |
*/ |
| 63 |
if (WAIT_FOR_BBP(rt2x00dev, ®)) { |
| 64 |
reg = 0; |
| 65 |
rt2x00_set_field32(®, PHY_CSR3_VALUE, value); |
| 66 |
rt2x00_set_field32(®, PHY_CSR3_REGNUM, word); |
| 67 |
rt2x00_set_field32(®, PHY_CSR3_BUSY, 1); |
| 68 |
rt2x00_set_field32(®, PHY_CSR3_READ_CONTROL, 0); |
| 69 |
|
| 70 |
rt2x00usb_register_write_lock(rt2x00dev, PHY_CSR3, reg); |
| 71 |
} |
| 72 |
|
| 73 |
mutex_unlock(&rt2x00dev->csr_mutex); |
| 74 |
} |
| 75 |
|
| 76 |
static u8 rt73usb_bbp_read(struct rt2x00_dev *rt2x00dev, |
| 77 |
const unsigned int word) |
| 78 |
{ |
| 79 |
u32 reg; |
| 80 |
u8 value; |
| 81 |
|
| 82 |
mutex_lock(&rt2x00dev->csr_mutex); |
| 83 |
|
| 84 |
/* |
| 85 |
* Wait until the BBP becomes available, afterwards we |
| 86 |
* can safely write the read request into the register. |
| 87 |
* After the data has been written, we wait until hardware |
| 88 |
* returns the correct value, if at any time the register |
| 89 |
* doesn't become available in time, reg will be 0xffffffff |
| 90 |
* which means we return 0xff to the caller. |
| 91 |
*/ |
| 92 |
if (WAIT_FOR_BBP(rt2x00dev, ®)) { |
| 93 |
reg = 0; |
| 94 |
rt2x00_set_field32(®, PHY_CSR3_REGNUM, word); |
| 95 |
rt2x00_set_field32(®, PHY_CSR3_BUSY, 1); |
| 96 |
rt2x00_set_field32(®, PHY_CSR3_READ_CONTROL, 1); |
| 97 |
|
| 98 |
rt2x00usb_register_write_lock(rt2x00dev, PHY_CSR3, reg); |
| 99 |
|
| 100 |
WAIT_FOR_BBP(rt2x00dev, ®); |
| 101 |
} |
| 102 |
|
| 103 |
value = rt2x00_get_field32(reg, PHY_CSR3_VALUE); |
| 104 |
|
| 105 |
mutex_unlock(&rt2x00dev->csr_mutex); |
| 106 |
|
| 107 |
return value; |
| 108 |
} |
| 109 |
|
| 110 |
static void rt73usb_rf_write(struct rt2x00_dev *rt2x00dev, |
| 111 |
const unsigned int word, const u32 value) |
| 112 |
{ |
| 113 |
u32 reg; |
| 114 |
|
| 115 |
mutex_lock(&rt2x00dev->csr_mutex); |
| 116 |
|
| 117 |
/* |
| 118 |
* Wait until the RF becomes available, afterwards we |
| 119 |
* can safely write the new data into the register. |
| 120 |
*/ |
| 121 |
if (WAIT_FOR_RF(rt2x00dev, ®)) { |
| 122 |
reg = 0; |
| 123 |
rt2x00_set_field32(®, PHY_CSR4_VALUE, value); |
| 124 |
/* |
| 125 |
* RF5225 and RF2527 contain 21 bits per RF register value, |
| 126 |
* all others contain 20 bits. |
| 127 |
*/ |
| 128 |
rt2x00_set_field32(®, PHY_CSR4_NUMBER_OF_BITS, |
| 129 |
20 + (rt2x00_rf(rt2x00dev, RF5225) || |
| 130 |
rt2x00_rf(rt2x00dev, RF2527))); |
| 131 |
rt2x00_set_field32(®, PHY_CSR4_IF_SELECT, 0); |
| 132 |
rt2x00_set_field32(®, PHY_CSR4_BUSY, 1); |
| 133 |
|
| 134 |
rt2x00usb_register_write_lock(rt2x00dev, PHY_CSR4, reg); |
| 135 |
rt2x00_rf_write(rt2x00dev, word, value); |
| 136 |
} |
| 137 |
|
| 138 |
mutex_unlock(&rt2x00dev->csr_mutex); |
| 139 |
} |
| 140 |
|
| 141 |
#ifdef CONFIG_RT2X00_LIB_DEBUGFS |
| 142 |
static const struct rt2x00debug rt73usb_rt2x00debug = { |
| 143 |
.owner = THIS_MODULE, |
| 144 |
.csr = { |
| 145 |
.read = rt2x00usb_register_read, |
| 146 |
.write = rt2x00usb_register_write, |
| 147 |
.flags = RT2X00DEBUGFS_OFFSET, |
| 148 |
.word_base = CSR_REG_BASE, |
| 149 |
.word_size = sizeof(u32), |
| 150 |
.word_count = CSR_REG_SIZE / sizeof(u32), |
| 151 |
}, |
| 152 |
.eeprom = { |
| 153 |
.read = rt2x00_eeprom_read, |
| 154 |
.write = rt2x00_eeprom_write, |
| 155 |
.word_base = EEPROM_BASE, |
| 156 |
.word_size = sizeof(u16), |
| 157 |
.word_count = EEPROM_SIZE / sizeof(u16), |
| 158 |
}, |
| 159 |
.bbp = { |
| 160 |
.read = rt73usb_bbp_read, |
| 161 |
.write = rt73usb_bbp_write, |
| 162 |
.word_base = BBP_BASE, |
| 163 |
.word_size = sizeof(u8), |
| 164 |
.word_count = BBP_SIZE / sizeof(u8), |
| 165 |
}, |
| 166 |
.rf = { |
| 167 |
.read = rt2x00_rf_read, |
| 168 |
.write = rt73usb_rf_write, |
| 169 |
.word_base = RF_BASE, |
| 170 |
.word_size = sizeof(u32), |
| 171 |
.word_count = RF_SIZE / sizeof(u32), |
| 172 |
}, |
| 173 |
}; |
| 174 |
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ |
| 175 |
|
| 176 |
static int rt73usb_rfkill_poll(struct rt2x00_dev *rt2x00dev) |
| 177 |
{ |
| 178 |
u32 reg; |
| 179 |
|
| 180 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR13); |
| 181 |
return rt2x00_get_field32(reg, MAC_CSR13_VAL7); |
| 182 |
} |
| 183 |
|
| 184 |
#ifdef CONFIG_RT2X00_LIB_LEDS |
| 185 |
static void rt73usb_brightness_set(struct led_classdev *led_cdev, |
| 186 |
enum led_brightness brightness) |
| 187 |
{ |
| 188 |
struct rt2x00_led *led = |
| 189 |
container_of(led_cdev, struct rt2x00_led, led_dev); |
| 190 |
unsigned int enabled = brightness != LED_OFF; |
| 191 |
unsigned int a_mode = |
| 192 |
(enabled && led->rt2x00dev->curr_band == NL80211_BAND_5GHZ); |
| 193 |
unsigned int bg_mode = |
| 194 |
(enabled && led->rt2x00dev->curr_band == NL80211_BAND_2GHZ); |
| 195 |
|
| 196 |
if (led->type == LED_TYPE_RADIO) { |
| 197 |
rt2x00_set_field16(&led->rt2x00dev->led_mcu_reg, |
| 198 |
MCU_LEDCS_RADIO_STATUS, enabled); |
| 199 |
|
| 200 |
rt2x00usb_vendor_request_sw(led->rt2x00dev, USB_LED_CONTROL, |
| 201 |
0, led->rt2x00dev->led_mcu_reg, |
| 202 |
REGISTER_TIMEOUT); |
| 203 |
} else if (led->type == LED_TYPE_ASSOC) { |
| 204 |
rt2x00_set_field16(&led->rt2x00dev->led_mcu_reg, |
| 205 |
MCU_LEDCS_LINK_BG_STATUS, bg_mode); |
| 206 |
rt2x00_set_field16(&led->rt2x00dev->led_mcu_reg, |
| 207 |
MCU_LEDCS_LINK_A_STATUS, a_mode); |
| 208 |
|
| 209 |
rt2x00usb_vendor_request_sw(led->rt2x00dev, USB_LED_CONTROL, |
| 210 |
0, led->rt2x00dev->led_mcu_reg, |
| 211 |
REGISTER_TIMEOUT); |
| 212 |
} else if (led->type == LED_TYPE_QUALITY) { |
| 213 |
/* |
| 214 |
* The brightness is divided into 6 levels (0 - 5), |
| 215 |
* this means we need to convert the brightness |
| 216 |
* argument into the matching level within that range. |
| 217 |
*/ |
| 218 |
rt2x00usb_vendor_request_sw(led->rt2x00dev, USB_LED_CONTROL, |
| 219 |
brightness / (LED_FULL / 6), |
| 220 |
led->rt2x00dev->led_mcu_reg, |
| 221 |
REGISTER_TIMEOUT); |
| 222 |
} |
| 223 |
} |
| 224 |
|
| 225 |
static int rt73usb_blink_set(struct led_classdev *led_cdev, |
| 226 |
unsigned long *delay_on, |
| 227 |
unsigned long *delay_off) |
| 228 |
{ |
| 229 |
struct rt2x00_led *led = |
| 230 |
container_of(led_cdev, struct rt2x00_led, led_dev); |
| 231 |
u32 reg; |
| 232 |
|
| 233 |
reg = rt2x00usb_register_read(led->rt2x00dev, MAC_CSR14); |
| 234 |
rt2x00_set_field32(®, MAC_CSR14_ON_PERIOD, *delay_on); |
| 235 |
rt2x00_set_field32(®, MAC_CSR14_OFF_PERIOD, *delay_off); |
| 236 |
rt2x00usb_register_write(led->rt2x00dev, MAC_CSR14, reg); |
| 237 |
|
| 238 |
return 0; |
| 239 |
} |
| 240 |
|
| 241 |
static void rt73usb_init_led(struct rt2x00_dev *rt2x00dev, |
| 242 |
struct rt2x00_led *led, |
| 243 |
enum led_type type) |
| 244 |
{ |
| 245 |
led->rt2x00dev = rt2x00dev; |
| 246 |
led->type = type; |
| 247 |
led->led_dev.brightness_set = rt73usb_brightness_set; |
| 248 |
led->led_dev.blink_set = rt73usb_blink_set; |
| 249 |
led->flags = LED_INITIALIZED; |
| 250 |
} |
| 251 |
#endif /* CONFIG_RT2X00_LIB_LEDS */ |
| 252 |
|
| 253 |
/* |
| 254 |
* Configuration handlers. |
| 255 |
*/ |
| 256 |
static int rt73usb_config_shared_key(struct rt2x00_dev *rt2x00dev, |
| 257 |
struct rt2x00lib_crypto *crypto, |
| 258 |
struct ieee80211_key_conf *key) |
| 259 |
{ |
| 260 |
struct hw_key_entry key_entry; |
| 261 |
struct rt2x00_field32 field; |
| 262 |
u32 mask; |
| 263 |
u32 reg; |
| 264 |
|
| 265 |
if (crypto->cmd == SET_KEY) { |
| 266 |
/* |
| 267 |
* rt2x00lib can't determine the correct free |
| 268 |
* key_idx for shared keys. We have 1 register |
| 269 |
* with key valid bits. The goal is simple, read |
| 270 |
* the register, if that is full we have no slots |
| 271 |
* left. |
| 272 |
* Note that each BSS is allowed to have up to 4 |
| 273 |
* shared keys, so put a mask over the allowed |
| 274 |
* entries. |
| 275 |
*/ |
| 276 |
mask = (0xf << crypto->bssidx); |
| 277 |
|
| 278 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR0); |
| 279 |
reg &= mask; |
| 280 |
|
| 281 |
if (reg && reg == mask) |
| 282 |
return -ENOSPC; |
| 283 |
|
| 284 |
key->hw_key_idx += reg ? ffz(reg) : 0; |
| 285 |
|
| 286 |
/* |
| 287 |
* Upload key to hardware |
| 288 |
*/ |
| 289 |
memcpy(key_entry.key, crypto->key, |
| 290 |
sizeof(key_entry.key)); |
| 291 |
memcpy(key_entry.tx_mic, crypto->tx_mic, |
| 292 |
sizeof(key_entry.tx_mic)); |
| 293 |
memcpy(key_entry.rx_mic, crypto->rx_mic, |
| 294 |
sizeof(key_entry.rx_mic)); |
| 295 |
|
| 296 |
reg = SHARED_KEY_ENTRY(key->hw_key_idx); |
| 297 |
rt2x00usb_register_multiwrite(rt2x00dev, reg, |
| 298 |
&key_entry, sizeof(key_entry)); |
| 299 |
|
| 300 |
/* |
| 301 |
* The cipher types are stored over 2 registers. |
| 302 |
* bssidx 0 and 1 keys are stored in SEC_CSR1 and |
| 303 |
* bssidx 1 and 2 keys are stored in SEC_CSR5. |
| 304 |
* Using the correct defines correctly will cause overhead, |
| 305 |
* so just calculate the correct offset. |
| 306 |
*/ |
| 307 |
if (key->hw_key_idx < 8) { |
| 308 |
field.bit_offset = (3 * key->hw_key_idx); |
| 309 |
field.bit_mask = 0x7 << field.bit_offset; |
| 310 |
|
| 311 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR1); |
| 312 |
rt2x00_set_field32(®, field, crypto->cipher); |
| 313 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR1, reg); |
| 314 |
} else { |
| 315 |
field.bit_offset = (3 * (key->hw_key_idx - 8)); |
| 316 |
field.bit_mask = 0x7 << field.bit_offset; |
| 317 |
|
| 318 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR5); |
| 319 |
rt2x00_set_field32(®, field, crypto->cipher); |
| 320 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR5, reg); |
| 321 |
} |
| 322 |
|
| 323 |
/* |
| 324 |
* The driver does not support the IV/EIV generation |
| 325 |
* in hardware. However it doesn't support the IV/EIV |
| 326 |
* inside the ieee80211 frame either, but requires it |
| 327 |
* to be provided separately for the descriptor. |
| 328 |
* rt2x00lib will cut the IV/EIV data out of all frames |
| 329 |
* given to us by mac80211, but we must tell mac80211 |
| 330 |
* to generate the IV/EIV data. |
| 331 |
*/ |
| 332 |
key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| 333 |
} |
| 334 |
|
| 335 |
/* |
| 336 |
* SEC_CSR0 contains only single-bit fields to indicate |
| 337 |
* a particular key is valid. Because using the FIELD32() |
| 338 |
* defines directly will cause a lot of overhead we use |
| 339 |
* a calculation to determine the correct bit directly. |
| 340 |
*/ |
| 341 |
mask = 1 << key->hw_key_idx; |
| 342 |
|
| 343 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR0); |
| 344 |
if (crypto->cmd == SET_KEY) |
| 345 |
reg |= mask; |
| 346 |
else if (crypto->cmd == DISABLE_KEY) |
| 347 |
reg &= ~mask; |
| 348 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR0, reg); |
| 349 |
|
| 350 |
return 0; |
| 351 |
} |
| 352 |
|
| 353 |
static int rt73usb_config_pairwise_key(struct rt2x00_dev *rt2x00dev, |
| 354 |
struct rt2x00lib_crypto *crypto, |
| 355 |
struct ieee80211_key_conf *key) |
| 356 |
{ |
| 357 |
struct hw_pairwise_ta_entry addr_entry; |
| 358 |
struct hw_key_entry key_entry; |
| 359 |
u32 mask; |
| 360 |
u32 reg; |
| 361 |
|
| 362 |
if (crypto->cmd == SET_KEY) { |
| 363 |
/* |
| 364 |
* rt2x00lib can't determine the correct free |
| 365 |
* key_idx for pairwise keys. We have 2 registers |
| 366 |
* with key valid bits. The goal is simple, read |
| 367 |
* the first register, if that is full move to |
| 368 |
* the next register. |
| 369 |
* When both registers are full, we drop the key, |
| 370 |
* otherwise we use the first invalid entry. |
| 371 |
*/ |
| 372 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR2); |
| 373 |
if (reg && reg == ~0) { |
| 374 |
key->hw_key_idx = 32; |
| 375 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR3); |
| 376 |
if (reg && reg == ~0) |
| 377 |
return -ENOSPC; |
| 378 |
} |
| 379 |
|
| 380 |
key->hw_key_idx += reg ? ffz(reg) : 0; |
| 381 |
|
| 382 |
/* |
| 383 |
* Upload key to hardware |
| 384 |
*/ |
| 385 |
memcpy(key_entry.key, crypto->key, |
| 386 |
sizeof(key_entry.key)); |
| 387 |
memcpy(key_entry.tx_mic, crypto->tx_mic, |
| 388 |
sizeof(key_entry.tx_mic)); |
| 389 |
memcpy(key_entry.rx_mic, crypto->rx_mic, |
| 390 |
sizeof(key_entry.rx_mic)); |
| 391 |
|
| 392 |
reg = PAIRWISE_KEY_ENTRY(key->hw_key_idx); |
| 393 |
rt2x00usb_register_multiwrite(rt2x00dev, reg, |
| 394 |
&key_entry, sizeof(key_entry)); |
| 395 |
|
| 396 |
/* |
| 397 |
* Send the address and cipher type to the hardware register. |
| 398 |
*/ |
| 399 |
memset(&addr_entry, 0, sizeof(addr_entry)); |
| 400 |
memcpy(&addr_entry, crypto->address, ETH_ALEN); |
| 401 |
addr_entry.cipher = crypto->cipher; |
| 402 |
|
| 403 |
reg = PAIRWISE_TA_ENTRY(key->hw_key_idx); |
| 404 |
rt2x00usb_register_multiwrite(rt2x00dev, reg, |
| 405 |
&addr_entry, sizeof(addr_entry)); |
| 406 |
|
| 407 |
/* |
| 408 |
* Enable pairwise lookup table for given BSS idx, |
| 409 |
* without this received frames will not be decrypted |
| 410 |
* by the hardware. |
| 411 |
*/ |
| 412 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR4); |
| 413 |
reg |= (1 << crypto->bssidx); |
| 414 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR4, reg); |
| 415 |
|
| 416 |
/* |
| 417 |
* The driver does not support the IV/EIV generation |
| 418 |
* in hardware. However it doesn't support the IV/EIV |
| 419 |
* inside the ieee80211 frame either, but requires it |
| 420 |
* to be provided separately for the descriptor. |
| 421 |
* rt2x00lib will cut the IV/EIV data out of all frames |
| 422 |
* given to us by mac80211, but we must tell mac80211 |
| 423 |
* to generate the IV/EIV data. |
| 424 |
*/ |
| 425 |
key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| 426 |
} |
| 427 |
|
| 428 |
/* |
| 429 |
* SEC_CSR2 and SEC_CSR3 contain only single-bit fields to indicate |
| 430 |
* a particular key is valid. Because using the FIELD32() |
| 431 |
* defines directly will cause a lot of overhead we use |
| 432 |
* a calculation to determine the correct bit directly. |
| 433 |
*/ |
| 434 |
if (key->hw_key_idx < 32) { |
| 435 |
mask = 1 << key->hw_key_idx; |
| 436 |
|
| 437 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR2); |
| 438 |
if (crypto->cmd == SET_KEY) |
| 439 |
reg |= mask; |
| 440 |
else if (crypto->cmd == DISABLE_KEY) |
| 441 |
reg &= ~mask; |
| 442 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR2, reg); |
| 443 |
} else { |
| 444 |
mask = 1 << (key->hw_key_idx - 32); |
| 445 |
|
| 446 |
reg = rt2x00usb_register_read(rt2x00dev, SEC_CSR3); |
| 447 |
if (crypto->cmd == SET_KEY) |
| 448 |
reg |= mask; |
| 449 |
else if (crypto->cmd == DISABLE_KEY) |
| 450 |
reg &= ~mask; |
| 451 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR3, reg); |
| 452 |
} |
| 453 |
|
| 454 |
return 0; |
| 455 |
} |
| 456 |
|
| 457 |
static void rt73usb_config_filter(struct rt2x00_dev *rt2x00dev, |
| 458 |
const unsigned int filter_flags) |
| 459 |
{ |
| 460 |
u32 reg; |
| 461 |
|
| 462 |
/* |
| 463 |
* Start configuration steps. |
| 464 |
* Note that the version error will always be dropped |
| 465 |
* and broadcast frames will always be accepted since |
| 466 |
* there is no filter for it at this time. |
| 467 |
*/ |
| 468 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR0); |
| 469 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_CRC, |
| 470 |
!(filter_flags & FIF_FCSFAIL)); |
| 471 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_PHYSICAL, |
| 472 |
!(filter_flags & FIF_PLCPFAIL)); |
| 473 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_CONTROL, |
| 474 |
!(filter_flags & (FIF_CONTROL | FIF_PSPOLL))); |
| 475 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_NOT_TO_ME, |
| 476 |
!test_bit(CONFIG_MONITORING, &rt2x00dev->flags)); |
| 477 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_TO_DS, |
| 478 |
!test_bit(CONFIG_MONITORING, &rt2x00dev->flags) && |
| 479 |
!rt2x00dev->intf_ap_count); |
| 480 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_VERSION_ERROR, 1); |
| 481 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_MULTICAST, |
| 482 |
!(filter_flags & FIF_ALLMULTI)); |
| 483 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_BROADCAST, 0); |
| 484 |
rt2x00_set_field32(®, TXRX_CSR0_DROP_ACK_CTS, |
| 485 |
!(filter_flags & FIF_CONTROL)); |
| 486 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR0, reg); |
| 487 |
} |
| 488 |
|
| 489 |
static void rt73usb_config_intf(struct rt2x00_dev *rt2x00dev, |
| 490 |
struct rt2x00_intf *intf, |
| 491 |
struct rt2x00intf_conf *conf, |
| 492 |
const unsigned int flags) |
| 493 |
{ |
| 494 |
u32 reg; |
| 495 |
|
| 496 |
if (flags & CONFIG_UPDATE_TYPE) { |
| 497 |
/* |
| 498 |
* Enable synchronisation. |
| 499 |
*/ |
| 500 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR9); |
| 501 |
rt2x00_set_field32(®, TXRX_CSR9_TSF_SYNC, conf->sync); |
| 502 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, reg); |
| 503 |
} |
| 504 |
|
| 505 |
if (flags & CONFIG_UPDATE_MAC) { |
| 506 |
reg = le32_to_cpu(conf->mac[1]); |
| 507 |
rt2x00_set_field32(®, MAC_CSR3_UNICAST_TO_ME_MASK, 0xff); |
| 508 |
conf->mac[1] = cpu_to_le32(reg); |
| 509 |
|
| 510 |
rt2x00usb_register_multiwrite(rt2x00dev, MAC_CSR2, |
| 511 |
conf->mac, sizeof(conf->mac)); |
| 512 |
} |
| 513 |
|
| 514 |
if (flags & CONFIG_UPDATE_BSSID) { |
| 515 |
reg = le32_to_cpu(conf->bssid[1]); |
| 516 |
rt2x00_set_field32(®, MAC_CSR5_BSS_ID_MASK, 3); |
| 517 |
conf->bssid[1] = cpu_to_le32(reg); |
| 518 |
|
| 519 |
rt2x00usb_register_multiwrite(rt2x00dev, MAC_CSR4, |
| 520 |
conf->bssid, sizeof(conf->bssid)); |
| 521 |
} |
| 522 |
} |
| 523 |
|
| 524 |
static void rt73usb_config_erp(struct rt2x00_dev *rt2x00dev, |
| 525 |
struct rt2x00lib_erp *erp, |
| 526 |
u32 changed) |
| 527 |
{ |
| 528 |
u32 reg; |
| 529 |
|
| 530 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR0); |
| 531 |
rt2x00_set_field32(®, TXRX_CSR0_RX_ACK_TIMEOUT, 0x32); |
| 532 |
rt2x00_set_field32(®, TXRX_CSR0_TSF_OFFSET, IEEE80211_HEADER); |
| 533 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR0, reg); |
| 534 |
|
| 535 |
if (changed & BSS_CHANGED_ERP_PREAMBLE) { |
| 536 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR4); |
| 537 |
rt2x00_set_field32(®, TXRX_CSR4_AUTORESPOND_ENABLE, 1); |
| 538 |
rt2x00_set_field32(®, TXRX_CSR4_AUTORESPOND_PREAMBLE, |
| 539 |
!!erp->short_preamble); |
| 540 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR4, reg); |
| 541 |
} |
| 542 |
|
| 543 |
if (changed & BSS_CHANGED_BASIC_RATES) |
| 544 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR5, |
| 545 |
erp->basic_rates); |
| 546 |
|
| 547 |
if (changed & BSS_CHANGED_BEACON_INT) { |
| 548 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR9); |
| 549 |
rt2x00_set_field32(®, TXRX_CSR9_BEACON_INTERVAL, |
| 550 |
erp->beacon_int * 16); |
| 551 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, reg); |
| 552 |
} |
| 553 |
|
| 554 |
if (changed & BSS_CHANGED_ERP_SLOT) { |
| 555 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR9); |
| 556 |
rt2x00_set_field32(®, MAC_CSR9_SLOT_TIME, erp->slot_time); |
| 557 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR9, reg); |
| 558 |
|
| 559 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR8); |
| 560 |
rt2x00_set_field32(®, MAC_CSR8_SIFS, erp->sifs); |
| 561 |
rt2x00_set_field32(®, MAC_CSR8_SIFS_AFTER_RX_OFDM, 3); |
| 562 |
rt2x00_set_field32(®, MAC_CSR8_EIFS, erp->eifs); |
| 563 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR8, reg); |
| 564 |
} |
| 565 |
} |
| 566 |
|
| 567 |
static void rt73usb_config_antenna_5x(struct rt2x00_dev *rt2x00dev, |
| 568 |
struct antenna_setup *ant) |
| 569 |
{ |
| 570 |
u8 r3; |
| 571 |
u8 r4; |
| 572 |
u8 r77; |
| 573 |
u8 temp; |
| 574 |
|
| 575 |
r3 = rt73usb_bbp_read(rt2x00dev, 3); |
| 576 |
r4 = rt73usb_bbp_read(rt2x00dev, 4); |
| 577 |
r77 = rt73usb_bbp_read(rt2x00dev, 77); |
| 578 |
|
| 579 |
rt2x00_set_field8(&r3, BBP_R3_SMART_MODE, 0); |
| 580 |
|
| 581 |
/* |
| 582 |
* Configure the RX antenna. |
| 583 |
*/ |
| 584 |
switch (ant->rx) { |
| 585 |
case ANTENNA_HW_DIVERSITY: |
| 586 |
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA_CONTROL, 2); |
| 587 |
temp = !rt2x00_has_cap_frame_type(rt2x00dev) && |
| 588 |
(rt2x00dev->curr_band != NL80211_BAND_5GHZ); |
| 589 |
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, temp); |
| 590 |
break; |
| 591 |
case ANTENNA_A: |
| 592 |
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA_CONTROL, 1); |
| 593 |
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 0); |
| 594 |
if (rt2x00dev->curr_band == NL80211_BAND_5GHZ) |
| 595 |
rt2x00_set_field8(&r77, BBP_R77_RX_ANTENNA, 0); |
| 596 |
else |
| 597 |
rt2x00_set_field8(&r77, BBP_R77_RX_ANTENNA, 3); |
| 598 |
break; |
| 599 |
case ANTENNA_B: |
| 600 |
default: |
| 601 |
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA_CONTROL, 1); |
| 602 |
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 0); |
| 603 |
if (rt2x00dev->curr_band == NL80211_BAND_5GHZ) |
| 604 |
rt2x00_set_field8(&r77, BBP_R77_RX_ANTENNA, 3); |
| 605 |
else |
| 606 |
rt2x00_set_field8(&r77, BBP_R77_RX_ANTENNA, 0); |
| 607 |
break; |
| 608 |
} |
| 609 |
|
| 610 |
rt73usb_bbp_write(rt2x00dev, 77, r77); |
| 611 |
rt73usb_bbp_write(rt2x00dev, 3, r3); |
| 612 |
rt73usb_bbp_write(rt2x00dev, 4, r4); |
| 613 |
} |
| 614 |
|
| 615 |
static void rt73usb_config_antenna_2x(struct rt2x00_dev *rt2x00dev, |
| 616 |
struct antenna_setup *ant) |
| 617 |
{ |
| 618 |
u8 r3; |
| 619 |
u8 r4; |
| 620 |
u8 r77; |
| 621 |
|
| 622 |
r3 = rt73usb_bbp_read(rt2x00dev, 3); |
| 623 |
r4 = rt73usb_bbp_read(rt2x00dev, 4); |
| 624 |
r77 = rt73usb_bbp_read(rt2x00dev, 77); |
| 625 |
|
| 626 |
rt2x00_set_field8(&r3, BBP_R3_SMART_MODE, 0); |
| 627 |
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, |
| 628 |
!rt2x00_has_cap_frame_type(rt2x00dev)); |
| 629 |
|
| 630 |
/* |
| 631 |
* Configure the RX antenna. |
| 632 |
*/ |
| 633 |
switch (ant->rx) { |
| 634 |
case ANTENNA_HW_DIVERSITY: |
| 635 |
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA_CONTROL, 2); |
| 636 |
break; |
| 637 |
case ANTENNA_A: |
| 638 |
rt2x00_set_field8(&r77, BBP_R77_RX_ANTENNA, 3); |
| 639 |
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA_CONTROL, 1); |
| 640 |
break; |
| 641 |
case ANTENNA_B: |
| 642 |
default: |
| 643 |
rt2x00_set_field8(&r77, BBP_R77_RX_ANTENNA, 0); |
| 644 |
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA_CONTROL, 1); |
| 645 |
break; |
| 646 |
} |
| 647 |
|
| 648 |
rt73usb_bbp_write(rt2x00dev, 77, r77); |
| 649 |
rt73usb_bbp_write(rt2x00dev, 3, r3); |
| 650 |
rt73usb_bbp_write(rt2x00dev, 4, r4); |
| 651 |
} |
| 652 |
|
| 653 |
struct antenna_sel { |
| 654 |
u8 word; |
| 655 |
/* |
| 656 |
* value[0] -> non-LNA |
| 657 |
* value[1] -> LNA |
| 658 |
*/ |
| 659 |
u8 value[2]; |
| 660 |
}; |
| 661 |
|
| 662 |
static const struct antenna_sel antenna_sel_a[] = { |
| 663 |
{ 96, { 0x58, 0x78 } }, |
| 664 |
{ 104, { 0x38, 0x48 } }, |
| 665 |
{ 75, { 0xfe, 0x80 } }, |
| 666 |
{ 86, { 0xfe, 0x80 } }, |
| 667 |
{ 88, { 0xfe, 0x80 } }, |
| 668 |
{ 35, { 0x60, 0x60 } }, |
| 669 |
{ 97, { 0x58, 0x58 } }, |
| 670 |
{ 98, { 0x58, 0x58 } }, |
| 671 |
}; |
| 672 |
|
| 673 |
static const struct antenna_sel antenna_sel_bg[] = { |
| 674 |
{ 96, { 0x48, 0x68 } }, |
| 675 |
{ 104, { 0x2c, 0x3c } }, |
| 676 |
{ 75, { 0xfe, 0x80 } }, |
| 677 |
{ 86, { 0xfe, 0x80 } }, |
| 678 |
{ 88, { 0xfe, 0x80 } }, |
| 679 |
{ 35, { 0x50, 0x50 } }, |
| 680 |
{ 97, { 0x48, 0x48 } }, |
| 681 |
{ 98, { 0x48, 0x48 } }, |
| 682 |
}; |
| 683 |
|
| 684 |
static void rt73usb_config_ant(struct rt2x00_dev *rt2x00dev, |
| 685 |
struct antenna_setup *ant) |
| 686 |
{ |
| 687 |
const struct antenna_sel *sel; |
| 688 |
unsigned int lna; |
| 689 |
unsigned int i; |
| 690 |
u32 reg; |
| 691 |
|
| 692 |
/* |
| 693 |
* We should never come here because rt2x00lib is supposed |
| 694 |
* to catch this and send us the correct antenna explicitely. |
| 695 |
*/ |
| 696 |
BUG_ON(ant->rx == ANTENNA_SW_DIVERSITY || |
| 697 |
ant->tx == ANTENNA_SW_DIVERSITY); |
| 698 |
|
| 699 |
if (rt2x00dev->curr_band == NL80211_BAND_5GHZ) { |
| 700 |
sel = antenna_sel_a; |
| 701 |
lna = rt2x00_has_cap_external_lna_a(rt2x00dev); |
| 702 |
} else { |
| 703 |
sel = antenna_sel_bg; |
| 704 |
lna = rt2x00_has_cap_external_lna_bg(rt2x00dev); |
| 705 |
} |
| 706 |
|
| 707 |
for (i = 0; i < ARRAY_SIZE(antenna_sel_a); i++) |
| 708 |
rt73usb_bbp_write(rt2x00dev, sel[i].word, sel[i].value[lna]); |
| 709 |
|
| 710 |
reg = rt2x00usb_register_read(rt2x00dev, PHY_CSR0); |
| 711 |
|
| 712 |
rt2x00_set_field32(®, PHY_CSR0_PA_PE_BG, |
| 713 |
(rt2x00dev->curr_band == NL80211_BAND_2GHZ)); |
| 714 |
rt2x00_set_field32(®, PHY_CSR0_PA_PE_A, |
| 715 |
(rt2x00dev->curr_band == NL80211_BAND_5GHZ)); |
| 716 |
|
| 717 |
rt2x00usb_register_write(rt2x00dev, PHY_CSR0, reg); |
| 718 |
|
| 719 |
if (rt2x00_rf(rt2x00dev, RF5226) || rt2x00_rf(rt2x00dev, RF5225)) |
| 720 |
rt73usb_config_antenna_5x(rt2x00dev, ant); |
| 721 |
else if (rt2x00_rf(rt2x00dev, RF2528) || rt2x00_rf(rt2x00dev, RF2527)) |
| 722 |
rt73usb_config_antenna_2x(rt2x00dev, ant); |
| 723 |
} |
| 724 |
|
| 725 |
static void rt73usb_config_lna_gain(struct rt2x00_dev *rt2x00dev, |
| 726 |
struct rt2x00lib_conf *libconf) |
| 727 |
{ |
| 728 |
u16 eeprom; |
| 729 |
short lna_gain = 0; |
| 730 |
|
| 731 |
if (libconf->conf->chandef.chan->band == NL80211_BAND_2GHZ) { |
| 732 |
if (rt2x00_has_cap_external_lna_bg(rt2x00dev)) |
| 733 |
lna_gain += 14; |
| 734 |
|
| 735 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_BG); |
| 736 |
lna_gain -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_BG_1); |
| 737 |
} else { |
| 738 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_A); |
| 739 |
lna_gain -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_A_1); |
| 740 |
} |
| 741 |
|
| 742 |
rt2x00dev->lna_gain = lna_gain; |
| 743 |
} |
| 744 |
|
| 745 |
static void rt73usb_config_channel(struct rt2x00_dev *rt2x00dev, |
| 746 |
struct rf_channel *rf, const int txpower) |
| 747 |
{ |
| 748 |
u8 r3; |
| 749 |
u8 r94; |
| 750 |
u8 smart; |
| 751 |
|
| 752 |
rt2x00_set_field32(&rf->rf3, RF3_TXPOWER, TXPOWER_TO_DEV(txpower)); |
| 753 |
rt2x00_set_field32(&rf->rf4, RF4_FREQ_OFFSET, rt2x00dev->freq_offset); |
| 754 |
|
| 755 |
smart = !(rt2x00_rf(rt2x00dev, RF5225) || rt2x00_rf(rt2x00dev, RF2527)); |
| 756 |
|
| 757 |
r3 = rt73usb_bbp_read(rt2x00dev, 3); |
| 758 |
rt2x00_set_field8(&r3, BBP_R3_SMART_MODE, smart); |
| 759 |
rt73usb_bbp_write(rt2x00dev, 3, r3); |
| 760 |
|
| 761 |
r94 = 6; |
| 762 |
if (txpower > MAX_TXPOWER && txpower <= (MAX_TXPOWER + r94)) |
| 763 |
r94 += txpower - MAX_TXPOWER; |
| 764 |
else if (txpower < MIN_TXPOWER && txpower >= (MIN_TXPOWER - r94)) |
| 765 |
r94 += txpower; |
| 766 |
rt73usb_bbp_write(rt2x00dev, 94, r94); |
| 767 |
|
| 768 |
rt73usb_rf_write(rt2x00dev, 1, rf->rf1); |
| 769 |
rt73usb_rf_write(rt2x00dev, 2, rf->rf2); |
| 770 |
rt73usb_rf_write(rt2x00dev, 3, rf->rf3 & ~0x00000004); |
| 771 |
rt73usb_rf_write(rt2x00dev, 4, rf->rf4); |
| 772 |
|
| 773 |
rt73usb_rf_write(rt2x00dev, 1, rf->rf1); |
| 774 |
rt73usb_rf_write(rt2x00dev, 2, rf->rf2); |
| 775 |
rt73usb_rf_write(rt2x00dev, 3, rf->rf3 | 0x00000004); |
| 776 |
rt73usb_rf_write(rt2x00dev, 4, rf->rf4); |
| 777 |
|
| 778 |
rt73usb_rf_write(rt2x00dev, 1, rf->rf1); |
| 779 |
rt73usb_rf_write(rt2x00dev, 2, rf->rf2); |
| 780 |
rt73usb_rf_write(rt2x00dev, 3, rf->rf3 & ~0x00000004); |
| 781 |
rt73usb_rf_write(rt2x00dev, 4, rf->rf4); |
| 782 |
|
| 783 |
udelay(10); |
| 784 |
} |
| 785 |
|
| 786 |
static void rt73usb_config_txpower(struct rt2x00_dev *rt2x00dev, |
| 787 |
const int txpower) |
| 788 |
{ |
| 789 |
struct rf_channel rf; |
| 790 |
|
| 791 |
rf.rf1 = rt2x00_rf_read(rt2x00dev, 1); |
| 792 |
rf.rf2 = rt2x00_rf_read(rt2x00dev, 2); |
| 793 |
rf.rf3 = rt2x00_rf_read(rt2x00dev, 3); |
| 794 |
rf.rf4 = rt2x00_rf_read(rt2x00dev, 4); |
| 795 |
|
| 796 |
rt73usb_config_channel(rt2x00dev, &rf, txpower); |
| 797 |
} |
| 798 |
|
| 799 |
static void rt73usb_config_retry_limit(struct rt2x00_dev *rt2x00dev, |
| 800 |
struct rt2x00lib_conf *libconf) |
| 801 |
{ |
| 802 |
u32 reg; |
| 803 |
|
| 804 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR4); |
| 805 |
rt2x00_set_field32(®, TXRX_CSR4_OFDM_TX_RATE_DOWN, 1); |
| 806 |
rt2x00_set_field32(®, TXRX_CSR4_OFDM_TX_RATE_STEP, 0); |
| 807 |
rt2x00_set_field32(®, TXRX_CSR4_OFDM_TX_FALLBACK_CCK, 0); |
| 808 |
rt2x00_set_field32(®, TXRX_CSR4_LONG_RETRY_LIMIT, |
| 809 |
libconf->conf->long_frame_max_tx_count); |
| 810 |
rt2x00_set_field32(®, TXRX_CSR4_SHORT_RETRY_LIMIT, |
| 811 |
libconf->conf->short_frame_max_tx_count); |
| 812 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR4, reg); |
| 813 |
} |
| 814 |
|
| 815 |
static void rt73usb_config_ps(struct rt2x00_dev *rt2x00dev, |
| 816 |
struct rt2x00lib_conf *libconf) |
| 817 |
{ |
| 818 |
enum dev_state state = |
| 819 |
(libconf->conf->flags & IEEE80211_CONF_PS) ? |
| 820 |
STATE_SLEEP : STATE_AWAKE; |
| 821 |
u32 reg; |
| 822 |
|
| 823 |
if (state == STATE_SLEEP) { |
| 824 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR11); |
| 825 |
rt2x00_set_field32(®, MAC_CSR11_DELAY_AFTER_TBCN, |
| 826 |
rt2x00dev->beacon_int - 10); |
| 827 |
rt2x00_set_field32(®, MAC_CSR11_TBCN_BEFORE_WAKEUP, |
| 828 |
libconf->conf->listen_interval - 1); |
| 829 |
rt2x00_set_field32(®, MAC_CSR11_WAKEUP_LATENCY, 5); |
| 830 |
|
| 831 |
/* We must first disable autowake before it can be enabled */ |
| 832 |
rt2x00_set_field32(®, MAC_CSR11_AUTOWAKE, 0); |
| 833 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR11, reg); |
| 834 |
|
| 835 |
rt2x00_set_field32(®, MAC_CSR11_AUTOWAKE, 1); |
| 836 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR11, reg); |
| 837 |
|
| 838 |
rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0, |
| 839 |
USB_MODE_SLEEP, REGISTER_TIMEOUT); |
| 840 |
} else { |
| 841 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR11); |
| 842 |
rt2x00_set_field32(®, MAC_CSR11_DELAY_AFTER_TBCN, 0); |
| 843 |
rt2x00_set_field32(®, MAC_CSR11_TBCN_BEFORE_WAKEUP, 0); |
| 844 |
rt2x00_set_field32(®, MAC_CSR11_AUTOWAKE, 0); |
| 845 |
rt2x00_set_field32(®, MAC_CSR11_WAKEUP_LATENCY, 0); |
| 846 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR11, reg); |
| 847 |
|
| 848 |
rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0, |
| 849 |
USB_MODE_WAKEUP, REGISTER_TIMEOUT); |
| 850 |
} |
| 851 |
} |
| 852 |
|
| 853 |
static void rt73usb_config(struct rt2x00_dev *rt2x00dev, |
| 854 |
struct rt2x00lib_conf *libconf, |
| 855 |
const unsigned int flags) |
| 856 |
{ |
| 857 |
/* Always recalculate LNA gain before changing configuration */ |
| 858 |
rt73usb_config_lna_gain(rt2x00dev, libconf); |
| 859 |
|
| 860 |
if (flags & IEEE80211_CONF_CHANGE_CHANNEL) |
| 861 |
rt73usb_config_channel(rt2x00dev, &libconf->rf, |
| 862 |
libconf->conf->power_level); |
| 863 |
if ((flags & IEEE80211_CONF_CHANGE_POWER) && |
| 864 |
!(flags & IEEE80211_CONF_CHANGE_CHANNEL)) |
| 865 |
rt73usb_config_txpower(rt2x00dev, libconf->conf->power_level); |
| 866 |
if (flags & IEEE80211_CONF_CHANGE_RETRY_LIMITS) |
| 867 |
rt73usb_config_retry_limit(rt2x00dev, libconf); |
| 868 |
if (flags & IEEE80211_CONF_CHANGE_PS) |
| 869 |
rt73usb_config_ps(rt2x00dev, libconf); |
| 870 |
} |
| 871 |
|
| 872 |
/* |
| 873 |
* Link tuning |
| 874 |
*/ |
| 875 |
static void rt73usb_link_stats(struct rt2x00_dev *rt2x00dev, |
| 876 |
struct link_qual *qual) |
| 877 |
{ |
| 878 |
u32 reg; |
| 879 |
|
| 880 |
/* |
| 881 |
* Update FCS error count from register. |
| 882 |
*/ |
| 883 |
reg = rt2x00usb_register_read(rt2x00dev, STA_CSR0); |
| 884 |
qual->rx_failed = rt2x00_get_field32(reg, STA_CSR0_FCS_ERROR); |
| 885 |
|
| 886 |
/* |
| 887 |
* Update False CCA count from register. |
| 888 |
*/ |
| 889 |
reg = rt2x00usb_register_read(rt2x00dev, STA_CSR1); |
| 890 |
qual->false_cca = rt2x00_get_field32(reg, STA_CSR1_FALSE_CCA_ERROR); |
| 891 |
} |
| 892 |
|
| 893 |
static inline void rt73usb_set_vgc(struct rt2x00_dev *rt2x00dev, |
| 894 |
struct link_qual *qual, u8 vgc_level) |
| 895 |
{ |
| 896 |
if (qual->vgc_level != vgc_level) { |
| 897 |
rt73usb_bbp_write(rt2x00dev, 17, vgc_level); |
| 898 |
qual->vgc_level = vgc_level; |
| 899 |
qual->vgc_level_reg = vgc_level; |
| 900 |
} |
| 901 |
} |
| 902 |
|
| 903 |
static void rt73usb_reset_tuner(struct rt2x00_dev *rt2x00dev, |
| 904 |
struct link_qual *qual) |
| 905 |
{ |
| 906 |
rt73usb_set_vgc(rt2x00dev, qual, 0x20); |
| 907 |
} |
| 908 |
|
| 909 |
static void rt73usb_link_tuner(struct rt2x00_dev *rt2x00dev, |
| 910 |
struct link_qual *qual, const u32 count) |
| 911 |
{ |
| 912 |
u8 up_bound; |
| 913 |
u8 low_bound; |
| 914 |
|
| 915 |
/* |
| 916 |
* Determine r17 bounds. |
| 917 |
*/ |
| 918 |
if (rt2x00dev->curr_band == NL80211_BAND_5GHZ) { |
| 919 |
low_bound = 0x28; |
| 920 |
up_bound = 0x48; |
| 921 |
|
| 922 |
if (rt2x00_has_cap_external_lna_a(rt2x00dev)) { |
| 923 |
low_bound += 0x10; |
| 924 |
up_bound += 0x10; |
| 925 |
} |
| 926 |
} else { |
| 927 |
if (qual->rssi > -82) { |
| 928 |
low_bound = 0x1c; |
| 929 |
up_bound = 0x40; |
| 930 |
} else if (qual->rssi > -84) { |
| 931 |
low_bound = 0x1c; |
| 932 |
up_bound = 0x20; |
| 933 |
} else { |
| 934 |
low_bound = 0x1c; |
| 935 |
up_bound = 0x1c; |
| 936 |
} |
| 937 |
|
| 938 |
if (rt2x00_has_cap_external_lna_bg(rt2x00dev)) { |
| 939 |
low_bound += 0x14; |
| 940 |
up_bound += 0x10; |
| 941 |
} |
| 942 |
} |
| 943 |
|
| 944 |
/* |
| 945 |
* If we are not associated, we should go straight to the |
| 946 |
* dynamic CCA tuning. |
| 947 |
*/ |
| 948 |
if (!rt2x00dev->intf_associated) |
| 949 |
goto dynamic_cca_tune; |
| 950 |
|
| 951 |
/* |
| 952 |
* Special big-R17 for very short distance |
| 953 |
*/ |
| 954 |
if (qual->rssi > -35) { |
| 955 |
rt73usb_set_vgc(rt2x00dev, qual, 0x60); |
| 956 |
return; |
| 957 |
} |
| 958 |
|
| 959 |
/* |
| 960 |
* Special big-R17 for short distance |
| 961 |
*/ |
| 962 |
if (qual->rssi >= -58) { |
| 963 |
rt73usb_set_vgc(rt2x00dev, qual, up_bound); |
| 964 |
return; |
| 965 |
} |
| 966 |
|
| 967 |
/* |
| 968 |
* Special big-R17 for middle-short distance |
| 969 |
*/ |
| 970 |
if (qual->rssi >= -66) { |
| 971 |
rt73usb_set_vgc(rt2x00dev, qual, low_bound + 0x10); |
| 972 |
return; |
| 973 |
} |
| 974 |
|
| 975 |
/* |
| 976 |
* Special mid-R17 for middle distance |
| 977 |
*/ |
| 978 |
if (qual->rssi >= -74) { |
| 979 |
rt73usb_set_vgc(rt2x00dev, qual, low_bound + 0x08); |
| 980 |
return; |
| 981 |
} |
| 982 |
|
| 983 |
/* |
| 984 |
* Special case: Change up_bound based on the rssi. |
| 985 |
* Lower up_bound when rssi is weaker then -74 dBm. |
| 986 |
*/ |
| 987 |
up_bound -= 2 * (-74 - qual->rssi); |
| 988 |
if (low_bound > up_bound) |
| 989 |
up_bound = low_bound; |
| 990 |
|
| 991 |
if (qual->vgc_level > up_bound) { |
| 992 |
rt73usb_set_vgc(rt2x00dev, qual, up_bound); |
| 993 |
return; |
| 994 |
} |
| 995 |
|
| 996 |
dynamic_cca_tune: |
| 997 |
|
| 998 |
/* |
| 999 |
* r17 does not yet exceed upper limit, continue and base |
| 1000 |
* the r17 tuning on the false CCA count. |
| 1001 |
*/ |
| 1002 |
if ((qual->false_cca > 512) && (qual->vgc_level < up_bound)) |
| 1003 |
rt73usb_set_vgc(rt2x00dev, qual, |
| 1004 |
min_t(u8, qual->vgc_level + 4, up_bound)); |
| 1005 |
else if ((qual->false_cca < 100) && (qual->vgc_level > low_bound)) |
| 1006 |
rt73usb_set_vgc(rt2x00dev, qual, |
| 1007 |
max_t(u8, qual->vgc_level - 4, low_bound)); |
| 1008 |
} |
| 1009 |
|
| 1010 |
/* |
| 1011 |
* Queue handlers. |
| 1012 |
*/ |
| 1013 |
static void rt73usb_start_queue(struct data_queue *queue) |
| 1014 |
{ |
| 1015 |
struct rt2x00_dev *rt2x00dev = queue->rt2x00dev; |
| 1016 |
u32 reg; |
| 1017 |
|
| 1018 |
switch (queue->qid) { |
| 1019 |
case QID_RX: |
| 1020 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR0); |
| 1021 |
rt2x00_set_field32(®, TXRX_CSR0_DISABLE_RX, 0); |
| 1022 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR0, reg); |
| 1023 |
break; |
| 1024 |
case QID_BEACON: |
| 1025 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR9); |
| 1026 |
rt2x00_set_field32(®, TXRX_CSR9_TSF_TICKING, 1); |
| 1027 |
rt2x00_set_field32(®, TXRX_CSR9_TBTT_ENABLE, 1); |
| 1028 |
rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 1); |
| 1029 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, reg); |
| 1030 |
break; |
| 1031 |
default: |
| 1032 |
break; |
| 1033 |
} |
| 1034 |
} |
| 1035 |
|
| 1036 |
static void rt73usb_stop_queue(struct data_queue *queue) |
| 1037 |
{ |
| 1038 |
struct rt2x00_dev *rt2x00dev = queue->rt2x00dev; |
| 1039 |
u32 reg; |
| 1040 |
|
| 1041 |
switch (queue->qid) { |
| 1042 |
case QID_RX: |
| 1043 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR0); |
| 1044 |
rt2x00_set_field32(®, TXRX_CSR0_DISABLE_RX, 1); |
| 1045 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR0, reg); |
| 1046 |
break; |
| 1047 |
case QID_BEACON: |
| 1048 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR9); |
| 1049 |
rt2x00_set_field32(®, TXRX_CSR9_TSF_TICKING, 0); |
| 1050 |
rt2x00_set_field32(®, TXRX_CSR9_TBTT_ENABLE, 0); |
| 1051 |
rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 0); |
| 1052 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, reg); |
| 1053 |
break; |
| 1054 |
default: |
| 1055 |
break; |
| 1056 |
} |
| 1057 |
} |
| 1058 |
|
| 1059 |
/* |
| 1060 |
* Firmware functions |
| 1061 |
*/ |
| 1062 |
static char *rt73usb_get_firmware_name(struct rt2x00_dev *rt2x00dev) |
| 1063 |
{ |
| 1064 |
return FIRMWARE_RT2571; |
| 1065 |
} |
| 1066 |
|
| 1067 |
static int rt73usb_check_firmware(struct rt2x00_dev *rt2x00dev, |
| 1068 |
const u8 *data, const size_t len) |
| 1069 |
{ |
| 1070 |
u16 fw_crc; |
| 1071 |
u16 crc; |
| 1072 |
|
| 1073 |
/* |
| 1074 |
* Only support 2kb firmware files. |
| 1075 |
*/ |
| 1076 |
if (len != 2048) |
| 1077 |
return FW_BAD_LENGTH; |
| 1078 |
|
| 1079 |
/* |
| 1080 |
* The last 2 bytes in the firmware array are the crc checksum itself, |
| 1081 |
* this means that we should never pass those 2 bytes to the crc |
| 1082 |
* algorithm. |
| 1083 |
*/ |
| 1084 |
fw_crc = (data[len - 2] << 8 | data[len - 1]); |
| 1085 |
|
| 1086 |
/* |
| 1087 |
* Use the crc itu-t algorithm. |
| 1088 |
*/ |
| 1089 |
crc = crc_itu_t(0, data, len - 2); |
| 1090 |
crc = crc_itu_t_byte(crc, 0); |
| 1091 |
crc = crc_itu_t_byte(crc, 0); |
| 1092 |
|
| 1093 |
return (fw_crc == crc) ? FW_OK : FW_BAD_CRC; |
| 1094 |
} |
| 1095 |
|
| 1096 |
static int rt73usb_load_firmware(struct rt2x00_dev *rt2x00dev, |
| 1097 |
const u8 *data, const size_t len) |
| 1098 |
{ |
| 1099 |
unsigned int i; |
| 1100 |
int status; |
| 1101 |
u32 reg; |
| 1102 |
|
| 1103 |
/* |
| 1104 |
* Wait for stable hardware. |
| 1105 |
*/ |
| 1106 |
for (i = 0; i < 100; i++) { |
| 1107 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR0); |
| 1108 |
if (reg) |
| 1109 |
break; |
| 1110 |
msleep(1); |
| 1111 |
} |
| 1112 |
|
| 1113 |
if (!reg) { |
| 1114 |
rt2x00_err(rt2x00dev, "Unstable hardware\n"); |
| 1115 |
return -EBUSY; |
| 1116 |
} |
| 1117 |
|
| 1118 |
/* |
| 1119 |
* Write firmware to device. |
| 1120 |
*/ |
| 1121 |
rt2x00usb_register_multiwrite(rt2x00dev, FIRMWARE_IMAGE_BASE, data, len); |
| 1122 |
|
| 1123 |
/* |
| 1124 |
* Send firmware request to device to load firmware, |
| 1125 |
* we need to specify a long timeout time. |
| 1126 |
*/ |
| 1127 |
status = rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, |
| 1128 |
0, USB_MODE_FIRMWARE, |
| 1129 |
REGISTER_TIMEOUT_FIRMWARE); |
| 1130 |
if (status < 0) { |
| 1131 |
rt2x00_err(rt2x00dev, "Failed to write Firmware to device\n"); |
| 1132 |
return status; |
| 1133 |
} |
| 1134 |
|
| 1135 |
return 0; |
| 1136 |
} |
| 1137 |
|
| 1138 |
/* |
| 1139 |
* Initialization functions. |
| 1140 |
*/ |
| 1141 |
static int rt73usb_init_registers(struct rt2x00_dev *rt2x00dev) |
| 1142 |
{ |
| 1143 |
u32 reg; |
| 1144 |
|
| 1145 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR0); |
| 1146 |
rt2x00_set_field32(®, TXRX_CSR0_AUTO_TX_SEQ, 1); |
| 1147 |
rt2x00_set_field32(®, TXRX_CSR0_DISABLE_RX, 0); |
| 1148 |
rt2x00_set_field32(®, TXRX_CSR0_TX_WITHOUT_WAITING, 0); |
| 1149 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR0, reg); |
| 1150 |
|
| 1151 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR1); |
| 1152 |
rt2x00_set_field32(®, TXRX_CSR1_BBP_ID0, 47); /* CCK Signal */ |
| 1153 |
rt2x00_set_field32(®, TXRX_CSR1_BBP_ID0_VALID, 1); |
| 1154 |
rt2x00_set_field32(®, TXRX_CSR1_BBP_ID1, 30); /* Rssi */ |
| 1155 |
rt2x00_set_field32(®, TXRX_CSR1_BBP_ID1_VALID, 1); |
| 1156 |
rt2x00_set_field32(®, TXRX_CSR1_BBP_ID2, 42); /* OFDM Rate */ |
| 1157 |
rt2x00_set_field32(®, TXRX_CSR1_BBP_ID2_VALID, 1); |
| 1158 |
rt2x00_set_field32(®, TXRX_CSR1_BBP_ID3, 30); /* Rssi */ |
| 1159 |
rt2x00_set_field32(®, TXRX_CSR1_BBP_ID3_VALID, 1); |
| 1160 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR1, reg); |
| 1161 |
|
| 1162 |
/* |
| 1163 |
* CCK TXD BBP registers |
| 1164 |
*/ |
| 1165 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR2); |
| 1166 |
rt2x00_set_field32(®, TXRX_CSR2_BBP_ID0, 13); |
| 1167 |
rt2x00_set_field32(®, TXRX_CSR2_BBP_ID0_VALID, 1); |
| 1168 |
rt2x00_set_field32(®, TXRX_CSR2_BBP_ID1, 12); |
| 1169 |
rt2x00_set_field32(®, TXRX_CSR2_BBP_ID1_VALID, 1); |
| 1170 |
rt2x00_set_field32(®, TXRX_CSR2_BBP_ID2, 11); |
| 1171 |
rt2x00_set_field32(®, TXRX_CSR2_BBP_ID2_VALID, 1); |
| 1172 |
rt2x00_set_field32(®, TXRX_CSR2_BBP_ID3, 10); |
| 1173 |
rt2x00_set_field32(®, TXRX_CSR2_BBP_ID3_VALID, 1); |
| 1174 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR2, reg); |
| 1175 |
|
| 1176 |
/* |
| 1177 |
* OFDM TXD BBP registers |
| 1178 |
*/ |
| 1179 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR3); |
| 1180 |
rt2x00_set_field32(®, TXRX_CSR3_BBP_ID0, 7); |
| 1181 |
rt2x00_set_field32(®, TXRX_CSR3_BBP_ID0_VALID, 1); |
| 1182 |
rt2x00_set_field32(®, TXRX_CSR3_BBP_ID1, 6); |
| 1183 |
rt2x00_set_field32(®, TXRX_CSR3_BBP_ID1_VALID, 1); |
| 1184 |
rt2x00_set_field32(®, TXRX_CSR3_BBP_ID2, 5); |
| 1185 |
rt2x00_set_field32(®, TXRX_CSR3_BBP_ID2_VALID, 1); |
| 1186 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR3, reg); |
| 1187 |
|
| 1188 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR7); |
| 1189 |
rt2x00_set_field32(®, TXRX_CSR7_ACK_CTS_6MBS, 59); |
| 1190 |
rt2x00_set_field32(®, TXRX_CSR7_ACK_CTS_9MBS, 53); |
| 1191 |
rt2x00_set_field32(®, TXRX_CSR7_ACK_CTS_12MBS, 49); |
| 1192 |
rt2x00_set_field32(®, TXRX_CSR7_ACK_CTS_18MBS, 46); |
| 1193 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR7, reg); |
| 1194 |
|
| 1195 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR8); |
| 1196 |
rt2x00_set_field32(®, TXRX_CSR8_ACK_CTS_24MBS, 44); |
| 1197 |
rt2x00_set_field32(®, TXRX_CSR8_ACK_CTS_36MBS, 42); |
| 1198 |
rt2x00_set_field32(®, TXRX_CSR8_ACK_CTS_48MBS, 42); |
| 1199 |
rt2x00_set_field32(®, TXRX_CSR8_ACK_CTS_54MBS, 42); |
| 1200 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR8, reg); |
| 1201 |
|
| 1202 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR9); |
| 1203 |
rt2x00_set_field32(®, TXRX_CSR9_BEACON_INTERVAL, 0); |
| 1204 |
rt2x00_set_field32(®, TXRX_CSR9_TSF_TICKING, 0); |
| 1205 |
rt2x00_set_field32(®, TXRX_CSR9_TSF_SYNC, 0); |
| 1206 |
rt2x00_set_field32(®, TXRX_CSR9_TBTT_ENABLE, 0); |
| 1207 |
rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 0); |
| 1208 |
rt2x00_set_field32(®, TXRX_CSR9_TIMESTAMP_COMPENSATE, 0); |
| 1209 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, reg); |
| 1210 |
|
| 1211 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR15, 0x0000000f); |
| 1212 |
|
| 1213 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR6); |
| 1214 |
rt2x00_set_field32(®, MAC_CSR6_MAX_FRAME_UNIT, 0xfff); |
| 1215 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR6, reg); |
| 1216 |
|
| 1217 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR10, 0x00000718); |
| 1218 |
|
| 1219 |
if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_AWAKE)) |
| 1220 |
return -EBUSY; |
| 1221 |
|
| 1222 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR13, 0x00007f00); |
| 1223 |
|
| 1224 |
/* |
| 1225 |
* Invalidate all Shared Keys (SEC_CSR0), |
| 1226 |
* and clear the Shared key Cipher algorithms (SEC_CSR1 & SEC_CSR5) |
| 1227 |
*/ |
| 1228 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR0, 0x00000000); |
| 1229 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR1, 0x00000000); |
| 1230 |
rt2x00usb_register_write(rt2x00dev, SEC_CSR5, 0x00000000); |
| 1231 |
|
| 1232 |
reg = 0x000023b0; |
| 1233 |
if (rt2x00_rf(rt2x00dev, RF5225) || rt2x00_rf(rt2x00dev, RF2527)) |
| 1234 |
rt2x00_set_field32(®, PHY_CSR1_RF_RPI, 1); |
| 1235 |
rt2x00usb_register_write(rt2x00dev, PHY_CSR1, reg); |
| 1236 |
|
| 1237 |
rt2x00usb_register_write(rt2x00dev, PHY_CSR5, 0x00040a06); |
| 1238 |
rt2x00usb_register_write(rt2x00dev, PHY_CSR6, 0x00080606); |
| 1239 |
rt2x00usb_register_write(rt2x00dev, PHY_CSR7, 0x00000408); |
| 1240 |
|
| 1241 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR9); |
| 1242 |
rt2x00_set_field32(®, MAC_CSR9_CW_SELECT, 0); |
| 1243 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR9, reg); |
| 1244 |
|
| 1245 |
/* |
| 1246 |
* Clear all beacons |
| 1247 |
* For the Beacon base registers we only need to clear |
| 1248 |
* the first byte since that byte contains the VALID and OWNER |
| 1249 |
* bits which (when set to 0) will invalidate the entire beacon. |
| 1250 |
*/ |
| 1251 |
rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE0, 0); |
| 1252 |
rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE1, 0); |
| 1253 |
rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE2, 0); |
| 1254 |
rt2x00usb_register_write(rt2x00dev, HW_BEACON_BASE3, 0); |
| 1255 |
|
| 1256 |
/* |
| 1257 |
* We must clear the error counters. |
| 1258 |
* These registers are cleared on read, |
| 1259 |
* so we may pass a useless variable to store the value. |
| 1260 |
*/ |
| 1261 |
reg = rt2x00usb_register_read(rt2x00dev, STA_CSR0); |
| 1262 |
reg = rt2x00usb_register_read(rt2x00dev, STA_CSR1); |
| 1263 |
reg = rt2x00usb_register_read(rt2x00dev, STA_CSR2); |
| 1264 |
|
| 1265 |
/* |
| 1266 |
* Reset MAC and BBP registers. |
| 1267 |
*/ |
| 1268 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR1); |
| 1269 |
rt2x00_set_field32(®, MAC_CSR1_SOFT_RESET, 1); |
| 1270 |
rt2x00_set_field32(®, MAC_CSR1_BBP_RESET, 1); |
| 1271 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR1, reg); |
| 1272 |
|
| 1273 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR1); |
| 1274 |
rt2x00_set_field32(®, MAC_CSR1_SOFT_RESET, 0); |
| 1275 |
rt2x00_set_field32(®, MAC_CSR1_BBP_RESET, 0); |
| 1276 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR1, reg); |
| 1277 |
|
| 1278 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR1); |
| 1279 |
rt2x00_set_field32(®, MAC_CSR1_HOST_READY, 1); |
| 1280 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR1, reg); |
| 1281 |
|
| 1282 |
return 0; |
| 1283 |
} |
| 1284 |
|
| 1285 |
static int rt73usb_wait_bbp_ready(struct rt2x00_dev *rt2x00dev) |
| 1286 |
{ |
| 1287 |
unsigned int i; |
| 1288 |
u8 value; |
| 1289 |
|
| 1290 |
for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) { |
| 1291 |
value = rt73usb_bbp_read(rt2x00dev, 0); |
| 1292 |
if ((value != 0xff) && (value != 0x00)) |
| 1293 |
return 0; |
| 1294 |
udelay(REGISTER_BUSY_DELAY); |
| 1295 |
} |
| 1296 |
|
| 1297 |
rt2x00_err(rt2x00dev, "BBP register access failed, aborting\n"); |
| 1298 |
return -EACCES; |
| 1299 |
} |
| 1300 |
|
| 1301 |
static int rt73usb_init_bbp(struct rt2x00_dev *rt2x00dev) |
| 1302 |
{ |
| 1303 |
unsigned int i; |
| 1304 |
u16 eeprom; |
| 1305 |
u8 reg_id; |
| 1306 |
u8 value; |
| 1307 |
|
| 1308 |
if (unlikely(rt73usb_wait_bbp_ready(rt2x00dev))) |
| 1309 |
return -EACCES; |
| 1310 |
|
| 1311 |
rt73usb_bbp_write(rt2x00dev, 3, 0x80); |
| 1312 |
rt73usb_bbp_write(rt2x00dev, 15, 0x30); |
| 1313 |
rt73usb_bbp_write(rt2x00dev, 21, 0xc8); |
| 1314 |
rt73usb_bbp_write(rt2x00dev, 22, 0x38); |
| 1315 |
rt73usb_bbp_write(rt2x00dev, 23, 0x06); |
| 1316 |
rt73usb_bbp_write(rt2x00dev, 24, 0xfe); |
| 1317 |
rt73usb_bbp_write(rt2x00dev, 25, 0x0a); |
| 1318 |
rt73usb_bbp_write(rt2x00dev, 26, 0x0d); |
| 1319 |
rt73usb_bbp_write(rt2x00dev, 32, 0x0b); |
| 1320 |
rt73usb_bbp_write(rt2x00dev, 34, 0x12); |
| 1321 |
rt73usb_bbp_write(rt2x00dev, 37, 0x07); |
| 1322 |
rt73usb_bbp_write(rt2x00dev, 39, 0xf8); |
| 1323 |
rt73usb_bbp_write(rt2x00dev, 41, 0x60); |
| 1324 |
rt73usb_bbp_write(rt2x00dev, 53, 0x10); |
| 1325 |
rt73usb_bbp_write(rt2x00dev, 54, 0x18); |
| 1326 |
rt73usb_bbp_write(rt2x00dev, 60, 0x10); |
| 1327 |
rt73usb_bbp_write(rt2x00dev, 61, 0x04); |
| 1328 |
rt73usb_bbp_write(rt2x00dev, 62, 0x04); |
| 1329 |
rt73usb_bbp_write(rt2x00dev, 75, 0xfe); |
| 1330 |
rt73usb_bbp_write(rt2x00dev, 86, 0xfe); |
| 1331 |
rt73usb_bbp_write(rt2x00dev, 88, 0xfe); |
| 1332 |
rt73usb_bbp_write(rt2x00dev, 90, 0x0f); |
| 1333 |
rt73usb_bbp_write(rt2x00dev, 99, 0x00); |
| 1334 |
rt73usb_bbp_write(rt2x00dev, 102, 0x16); |
| 1335 |
rt73usb_bbp_write(rt2x00dev, 107, 0x04); |
| 1336 |
|
| 1337 |
for (i = 0; i < EEPROM_BBP_SIZE; i++) { |
| 1338 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i); |
| 1339 |
|
| 1340 |
if (eeprom != 0xffff && eeprom != 0x0000) { |
| 1341 |
reg_id = rt2x00_get_field16(eeprom, EEPROM_BBP_REG_ID); |
| 1342 |
value = rt2x00_get_field16(eeprom, EEPROM_BBP_VALUE); |
| 1343 |
rt73usb_bbp_write(rt2x00dev, reg_id, value); |
| 1344 |
} |
| 1345 |
} |
| 1346 |
|
| 1347 |
return 0; |
| 1348 |
} |
| 1349 |
|
| 1350 |
/* |
| 1351 |
* Device state switch handlers. |
| 1352 |
*/ |
| 1353 |
static int rt73usb_enable_radio(struct rt2x00_dev *rt2x00dev) |
| 1354 |
{ |
| 1355 |
/* |
| 1356 |
* Initialize all registers. |
| 1357 |
*/ |
| 1358 |
if (unlikely(rt73usb_init_registers(rt2x00dev) || |
| 1359 |
rt73usb_init_bbp(rt2x00dev))) |
| 1360 |
return -EIO; |
| 1361 |
|
| 1362 |
return 0; |
| 1363 |
} |
| 1364 |
|
| 1365 |
static void rt73usb_disable_radio(struct rt2x00_dev *rt2x00dev) |
| 1366 |
{ |
| 1367 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR10, 0x00001818); |
| 1368 |
|
| 1369 |
/* |
| 1370 |
* Disable synchronisation. |
| 1371 |
*/ |
| 1372 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, 0); |
| 1373 |
|
| 1374 |
rt2x00usb_disable_radio(rt2x00dev); |
| 1375 |
} |
| 1376 |
|
| 1377 |
static int rt73usb_set_state(struct rt2x00_dev *rt2x00dev, enum dev_state state) |
| 1378 |
{ |
| 1379 |
u32 reg, reg2; |
| 1380 |
unsigned int i; |
| 1381 |
bool put_to_sleep; |
| 1382 |
|
| 1383 |
put_to_sleep = (state != STATE_AWAKE); |
| 1384 |
|
| 1385 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR12); |
| 1386 |
rt2x00_set_field32(®, MAC_CSR12_FORCE_WAKEUP, !put_to_sleep); |
| 1387 |
rt2x00_set_field32(®, MAC_CSR12_PUT_TO_SLEEP, put_to_sleep); |
| 1388 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR12, reg); |
| 1389 |
|
| 1390 |
/* |
| 1391 |
* Device is not guaranteed to be in the requested state yet. |
| 1392 |
* We must wait until the register indicates that the |
| 1393 |
* device has entered the correct state. |
| 1394 |
*/ |
| 1395 |
for (i = 0; i < REGISTER_BUSY_COUNT; i++) { |
| 1396 |
reg2 = rt2x00usb_register_read(rt2x00dev, MAC_CSR12); |
| 1397 |
state = rt2x00_get_field32(reg2, MAC_CSR12_BBP_CURRENT_STATE); |
| 1398 |
if (state == !put_to_sleep) |
| 1399 |
return 0; |
| 1400 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR12, reg); |
| 1401 |
msleep(10); |
| 1402 |
} |
| 1403 |
|
| 1404 |
return -EBUSY; |
| 1405 |
} |
| 1406 |
|
| 1407 |
static int rt73usb_set_device_state(struct rt2x00_dev *rt2x00dev, |
| 1408 |
enum dev_state state) |
| 1409 |
{ |
| 1410 |
int retval = 0; |
| 1411 |
|
| 1412 |
switch (state) { |
| 1413 |
case STATE_RADIO_ON: |
| 1414 |
retval = rt73usb_enable_radio(rt2x00dev); |
| 1415 |
break; |
| 1416 |
case STATE_RADIO_OFF: |
| 1417 |
rt73usb_disable_radio(rt2x00dev); |
| 1418 |
break; |
| 1419 |
case STATE_RADIO_IRQ_ON: |
| 1420 |
case STATE_RADIO_IRQ_OFF: |
| 1421 |
/* No support, but no error either */ |
| 1422 |
break; |
| 1423 |
case STATE_DEEP_SLEEP: |
| 1424 |
case STATE_SLEEP: |
| 1425 |
case STATE_STANDBY: |
| 1426 |
case STATE_AWAKE: |
| 1427 |
retval = rt73usb_set_state(rt2x00dev, state); |
| 1428 |
break; |
| 1429 |
default: |
| 1430 |
retval = -ENOTSUPP; |
| 1431 |
break; |
| 1432 |
} |
| 1433 |
|
| 1434 |
if (unlikely(retval)) |
| 1435 |
rt2x00_err(rt2x00dev, "Device failed to enter state %d (%d)\n", |
| 1436 |
state, retval); |
| 1437 |
|
| 1438 |
return retval; |
| 1439 |
} |
| 1440 |
|
| 1441 |
/* |
| 1442 |
* TX descriptor initialization |
| 1443 |
*/ |
| 1444 |
static void rt73usb_write_tx_desc(struct queue_entry *entry, |
| 1445 |
struct txentry_desc *txdesc) |
| 1446 |
{ |
| 1447 |
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); |
| 1448 |
__le32 *txd = (__le32 *) entry->skb->data; |
| 1449 |
u32 word; |
| 1450 |
|
| 1451 |
/* |
| 1452 |
* Start writing the descriptor words. |
| 1453 |
*/ |
| 1454 |
word = rt2x00_desc_read(txd, 0); |
| 1455 |
rt2x00_set_field32(&word, TXD_W0_BURST, |
| 1456 |
test_bit(ENTRY_TXD_BURST, &txdesc->flags)); |
| 1457 |
rt2x00_set_field32(&word, TXD_W0_VALID, 1); |
| 1458 |
rt2x00_set_field32(&word, TXD_W0_MORE_FRAG, |
| 1459 |
test_bit(ENTRY_TXD_MORE_FRAG, &txdesc->flags)); |
| 1460 |
rt2x00_set_field32(&word, TXD_W0_ACK, |
| 1461 |
test_bit(ENTRY_TXD_ACK, &txdesc->flags)); |
| 1462 |
rt2x00_set_field32(&word, TXD_W0_TIMESTAMP, |
| 1463 |
test_bit(ENTRY_TXD_REQ_TIMESTAMP, &txdesc->flags)); |
| 1464 |
rt2x00_set_field32(&word, TXD_W0_OFDM, |
| 1465 |
(txdesc->rate_mode == RATE_MODE_OFDM)); |
| 1466 |
rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->u.plcp.ifs); |
| 1467 |
rt2x00_set_field32(&word, TXD_W0_RETRY_MODE, |
| 1468 |
test_bit(ENTRY_TXD_RETRY_MODE, &txdesc->flags)); |
| 1469 |
rt2x00_set_field32(&word, TXD_W0_TKIP_MIC, |
| 1470 |
test_bit(ENTRY_TXD_ENCRYPT_MMIC, &txdesc->flags)); |
| 1471 |
rt2x00_set_field32(&word, TXD_W0_KEY_TABLE, |
| 1472 |
test_bit(ENTRY_TXD_ENCRYPT_PAIRWISE, &txdesc->flags)); |
| 1473 |
rt2x00_set_field32(&word, TXD_W0_KEY_INDEX, txdesc->key_idx); |
| 1474 |
rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, txdesc->length); |
| 1475 |
rt2x00_set_field32(&word, TXD_W0_BURST2, |
| 1476 |
test_bit(ENTRY_TXD_BURST, &txdesc->flags)); |
| 1477 |
rt2x00_set_field32(&word, TXD_W0_CIPHER_ALG, txdesc->cipher); |
| 1478 |
rt2x00_desc_write(txd, 0, word); |
| 1479 |
|
| 1480 |
word = rt2x00_desc_read(txd, 1); |
| 1481 |
rt2x00_set_field32(&word, TXD_W1_HOST_Q_ID, entry->queue->qid); |
| 1482 |
rt2x00_set_field32(&word, TXD_W1_AIFSN, entry->queue->aifs); |
| 1483 |
rt2x00_set_field32(&word, TXD_W1_CWMIN, entry->queue->cw_min); |
| 1484 |
rt2x00_set_field32(&word, TXD_W1_CWMAX, entry->queue->cw_max); |
| 1485 |
rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, txdesc->iv_offset); |
| 1486 |
rt2x00_set_field32(&word, TXD_W1_HW_SEQUENCE, |
| 1487 |
test_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags)); |
| 1488 |
rt2x00_desc_write(txd, 1, word); |
| 1489 |
|
| 1490 |
word = rt2x00_desc_read(txd, 2); |
| 1491 |
rt2x00_set_field32(&word, TXD_W2_PLCP_SIGNAL, txdesc->u.plcp.signal); |
| 1492 |
rt2x00_set_field32(&word, TXD_W2_PLCP_SERVICE, txdesc->u.plcp.service); |
| 1493 |
rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_LOW, |
| 1494 |
txdesc->u.plcp.length_low); |
| 1495 |
rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_HIGH, |
| 1496 |
txdesc->u.plcp.length_high); |
| 1497 |
rt2x00_desc_write(txd, 2, word); |
| 1498 |
|
| 1499 |
if (test_bit(ENTRY_TXD_ENCRYPT, &txdesc->flags)) { |
| 1500 |
_rt2x00_desc_write(txd, 3, skbdesc->iv[0]); |
| 1501 |
_rt2x00_desc_write(txd, 4, skbdesc->iv[1]); |
| 1502 |
} |
| 1503 |
|
| 1504 |
word = rt2x00_desc_read(txd, 5); |
| 1505 |
rt2x00_set_field32(&word, TXD_W5_TX_POWER, |
| 1506 |
TXPOWER_TO_DEV(entry->queue->rt2x00dev->tx_power)); |
| 1507 |
rt2x00_set_field32(&word, TXD_W5_WAITING_DMA_DONE_INT, 1); |
| 1508 |
rt2x00_desc_write(txd, 5, word); |
| 1509 |
|
| 1510 |
/* |
| 1511 |
* Register descriptor details in skb frame descriptor. |
| 1512 |
*/ |
| 1513 |
skbdesc->flags |= SKBDESC_DESC_IN_SKB; |
| 1514 |
skbdesc->desc = txd; |
| 1515 |
skbdesc->desc_len = TXD_DESC_SIZE; |
| 1516 |
} |
| 1517 |
|
| 1518 |
/* |
| 1519 |
* TX data initialization |
| 1520 |
*/ |
| 1521 |
static void rt73usb_write_beacon(struct queue_entry *entry, |
| 1522 |
struct txentry_desc *txdesc) |
| 1523 |
{ |
| 1524 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 1525 |
unsigned int beacon_base; |
| 1526 |
unsigned int padding_len; |
| 1527 |
u32 orig_reg, reg; |
| 1528 |
|
| 1529 |
/* |
| 1530 |
* Disable beaconing while we are reloading the beacon data, |
| 1531 |
* otherwise we might be sending out invalid data. |
| 1532 |
*/ |
| 1533 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR9); |
| 1534 |
orig_reg = reg; |
| 1535 |
rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 0); |
| 1536 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, reg); |
| 1537 |
|
| 1538 |
/* |
| 1539 |
* Add space for the descriptor in front of the skb. |
| 1540 |
*/ |
| 1541 |
skb_push(entry->skb, TXD_DESC_SIZE); |
| 1542 |
memset(entry->skb->data, 0, TXD_DESC_SIZE); |
| 1543 |
|
| 1544 |
/* |
| 1545 |
* Write the TX descriptor for the beacon. |
| 1546 |
*/ |
| 1547 |
rt73usb_write_tx_desc(entry, txdesc); |
| 1548 |
|
| 1549 |
/* |
| 1550 |
* Dump beacon to userspace through debugfs. |
| 1551 |
*/ |
| 1552 |
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_BEACON, entry); |
| 1553 |
|
| 1554 |
/* |
| 1555 |
* Write entire beacon with descriptor and padding to register. |
| 1556 |
*/ |
| 1557 |
padding_len = roundup(entry->skb->len, 4) - entry->skb->len; |
| 1558 |
if (padding_len && skb_pad(entry->skb, padding_len)) { |
| 1559 |
rt2x00_err(rt2x00dev, "Failure padding beacon, aborting\n"); |
| 1560 |
/* skb freed by skb_pad() on failure */ |
| 1561 |
entry->skb = NULL; |
| 1562 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, orig_reg); |
| 1563 |
return; |
| 1564 |
} |
| 1565 |
|
| 1566 |
beacon_base = HW_BEACON_OFFSET(entry->entry_idx); |
| 1567 |
rt2x00usb_register_multiwrite(rt2x00dev, beacon_base, entry->skb->data, |
| 1568 |
entry->skb->len + padding_len); |
| 1569 |
|
| 1570 |
/* |
| 1571 |
* Enable beaconing again. |
| 1572 |
* |
| 1573 |
* For Wi-Fi faily generated beacons between participating stations. |
| 1574 |
* Set TBTT phase adaptive adjustment step to 8us (default 16us) |
| 1575 |
*/ |
| 1576 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR10, 0x00001008); |
| 1577 |
|
| 1578 |
rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 1); |
| 1579 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, reg); |
| 1580 |
|
| 1581 |
/* |
| 1582 |
* Clean up the beacon skb. |
| 1583 |
*/ |
| 1584 |
dev_kfree_skb(entry->skb); |
| 1585 |
entry->skb = NULL; |
| 1586 |
} |
| 1587 |
|
| 1588 |
static void rt73usb_clear_beacon(struct queue_entry *entry) |
| 1589 |
{ |
| 1590 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 1591 |
unsigned int beacon_base; |
| 1592 |
u32 orig_reg, reg; |
| 1593 |
|
| 1594 |
/* |
| 1595 |
* Disable beaconing while we are reloading the beacon data, |
| 1596 |
* otherwise we might be sending out invalid data. |
| 1597 |
*/ |
| 1598 |
orig_reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR9); |
| 1599 |
reg = orig_reg; |
| 1600 |
rt2x00_set_field32(®, TXRX_CSR9_BEACON_GEN, 0); |
| 1601 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, reg); |
| 1602 |
|
| 1603 |
/* |
| 1604 |
* Clear beacon. |
| 1605 |
*/ |
| 1606 |
beacon_base = HW_BEACON_OFFSET(entry->entry_idx); |
| 1607 |
rt2x00usb_register_write(rt2x00dev, beacon_base, 0); |
| 1608 |
|
| 1609 |
/* |
| 1610 |
* Restore beaconing state. |
| 1611 |
*/ |
| 1612 |
rt2x00usb_register_write(rt2x00dev, TXRX_CSR9, orig_reg); |
| 1613 |
} |
| 1614 |
|
| 1615 |
static int rt73usb_get_tx_data_len(struct queue_entry *entry) |
| 1616 |
{ |
| 1617 |
int length; |
| 1618 |
|
| 1619 |
/* |
| 1620 |
* The length _must_ be a multiple of 4, |
| 1621 |
* but it must _not_ be a multiple of the USB packet size. |
| 1622 |
*/ |
| 1623 |
length = roundup(entry->skb->len, 4); |
| 1624 |
length += (4 * !(length % entry->queue->usb_maxpacket)); |
| 1625 |
|
| 1626 |
return length; |
| 1627 |
} |
| 1628 |
|
| 1629 |
/* |
| 1630 |
* RX control handlers |
| 1631 |
*/ |
| 1632 |
static int rt73usb_agc_to_rssi(struct rt2x00_dev *rt2x00dev, int rxd_w1) |
| 1633 |
{ |
| 1634 |
u8 offset = rt2x00dev->lna_gain; |
| 1635 |
u8 lna; |
| 1636 |
|
| 1637 |
lna = rt2x00_get_field32(rxd_w1, RXD_W1_RSSI_LNA); |
| 1638 |
switch (lna) { |
| 1639 |
case 3: |
| 1640 |
offset += 90; |
| 1641 |
break; |
| 1642 |
case 2: |
| 1643 |
offset += 74; |
| 1644 |
break; |
| 1645 |
case 1: |
| 1646 |
offset += 64; |
| 1647 |
break; |
| 1648 |
default: |
| 1649 |
return 0; |
| 1650 |
} |
| 1651 |
|
| 1652 |
if (rt2x00dev->curr_band == NL80211_BAND_5GHZ) { |
| 1653 |
if (rt2x00_has_cap_external_lna_a(rt2x00dev)) { |
| 1654 |
if (lna == 3 || lna == 2) |
| 1655 |
offset += 10; |
| 1656 |
} else { |
| 1657 |
if (lna == 3) |
| 1658 |
offset += 6; |
| 1659 |
else if (lna == 2) |
| 1660 |
offset += 8; |
| 1661 |
} |
| 1662 |
} |
| 1663 |
|
| 1664 |
return rt2x00_get_field32(rxd_w1, RXD_W1_RSSI_AGC) * 2 - offset; |
| 1665 |
} |
| 1666 |
|
| 1667 |
static void rt73usb_fill_rxdone(struct queue_entry *entry, |
| 1668 |
struct rxdone_entry_desc *rxdesc) |
| 1669 |
{ |
| 1670 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 1671 |
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); |
| 1672 |
__le32 *rxd = (__le32 *)entry->skb->data; |
| 1673 |
u32 word0; |
| 1674 |
u32 word1; |
| 1675 |
|
| 1676 |
/* |
| 1677 |
* Copy descriptor to the skbdesc->desc buffer, making it safe from moving of |
| 1678 |
* frame data in rt2x00usb. |
| 1679 |
*/ |
| 1680 |
memcpy(skbdesc->desc, rxd, skbdesc->desc_len); |
| 1681 |
rxd = (__le32 *)skbdesc->desc; |
| 1682 |
|
| 1683 |
/* |
| 1684 |
* It is now safe to read the descriptor on all architectures. |
| 1685 |
*/ |
| 1686 |
word0 = rt2x00_desc_read(rxd, 0); |
| 1687 |
word1 = rt2x00_desc_read(rxd, 1); |
| 1688 |
|
| 1689 |
if (rt2x00_get_field32(word0, RXD_W0_CRC_ERROR)) |
| 1690 |
rxdesc->flags |= RX_FLAG_FAILED_FCS_CRC; |
| 1691 |
|
| 1692 |
rxdesc->cipher = rt2x00_get_field32(word0, RXD_W0_CIPHER_ALG); |
| 1693 |
rxdesc->cipher_status = rt2x00_get_field32(word0, RXD_W0_CIPHER_ERROR); |
| 1694 |
|
| 1695 |
if (rxdesc->cipher != CIPHER_NONE) { |
| 1696 |
rxdesc->iv[0] = _rt2x00_desc_read(rxd, 2); |
| 1697 |
rxdesc->iv[1] = _rt2x00_desc_read(rxd, 3); |
| 1698 |
rxdesc->dev_flags |= RXDONE_CRYPTO_IV; |
| 1699 |
|
| 1700 |
rxdesc->icv = _rt2x00_desc_read(rxd, 4); |
| 1701 |
rxdesc->dev_flags |= RXDONE_CRYPTO_ICV; |
| 1702 |
|
| 1703 |
/* |
| 1704 |
* Hardware has stripped IV/EIV data from 802.11 frame during |
| 1705 |
* decryption. It has provided the data separately but rt2x00lib |
| 1706 |
* should decide if it should be reinserted. |
| 1707 |
*/ |
| 1708 |
rxdesc->flags |= RX_FLAG_IV_STRIPPED; |
| 1709 |
|
| 1710 |
/* |
| 1711 |
* The hardware has already checked the Michael Mic and has |
| 1712 |
* stripped it from the frame. Signal this to mac80211. |
| 1713 |
*/ |
| 1714 |
rxdesc->flags |= RX_FLAG_MMIC_STRIPPED; |
| 1715 |
|
| 1716 |
if (rxdesc->cipher_status == RX_CRYPTO_SUCCESS) |
| 1717 |
rxdesc->flags |= RX_FLAG_DECRYPTED; |
| 1718 |
else if (rxdesc->cipher_status == RX_CRYPTO_FAIL_MIC) |
| 1719 |
rxdesc->flags |= RX_FLAG_MMIC_ERROR; |
| 1720 |
} |
| 1721 |
|
| 1722 |
/* |
| 1723 |
* Obtain the status about this packet. |
| 1724 |
* When frame was received with an OFDM bitrate, |
| 1725 |
* the signal is the PLCP value. If it was received with |
| 1726 |
* a CCK bitrate the signal is the rate in 100kbit/s. |
| 1727 |
*/ |
| 1728 |
rxdesc->signal = rt2x00_get_field32(word1, RXD_W1_SIGNAL); |
| 1729 |
rxdesc->rssi = rt73usb_agc_to_rssi(rt2x00dev, word1); |
| 1730 |
rxdesc->size = rt2x00_get_field32(word0, RXD_W0_DATABYTE_COUNT); |
| 1731 |
|
| 1732 |
if (rt2x00_get_field32(word0, RXD_W0_OFDM)) |
| 1733 |
rxdesc->dev_flags |= RXDONE_SIGNAL_PLCP; |
| 1734 |
else |
| 1735 |
rxdesc->dev_flags |= RXDONE_SIGNAL_BITRATE; |
| 1736 |
if (rt2x00_get_field32(word0, RXD_W0_MY_BSS)) |
| 1737 |
rxdesc->dev_flags |= RXDONE_MY_BSS; |
| 1738 |
|
| 1739 |
/* |
| 1740 |
* Set skb pointers, and update frame information. |
| 1741 |
*/ |
| 1742 |
skb_pull(entry->skb, entry->queue->desc_size); |
| 1743 |
skb_trim(entry->skb, rxdesc->size); |
| 1744 |
} |
| 1745 |
|
| 1746 |
/* |
| 1747 |
* Device probe functions. |
| 1748 |
*/ |
| 1749 |
static int rt73usb_validate_eeprom(struct rt2x00_dev *rt2x00dev) |
| 1750 |
{ |
| 1751 |
u16 word; |
| 1752 |
u8 *mac; |
| 1753 |
s8 value; |
| 1754 |
|
| 1755 |
rt2x00usb_eeprom_read(rt2x00dev, rt2x00dev->eeprom, EEPROM_SIZE); |
| 1756 |
|
| 1757 |
/* |
| 1758 |
* Start validation of the data that has been read. |
| 1759 |
*/ |
| 1760 |
mac = rt2x00_eeprom_addr(rt2x00dev, EEPROM_MAC_ADDR_0); |
| 1761 |
rt2x00lib_set_mac_address(rt2x00dev, mac); |
| 1762 |
|
| 1763 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA); |
| 1764 |
if (word == 0xffff) { |
| 1765 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_NUM, 2); |
| 1766 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_TX_DEFAULT, |
| 1767 |
ANTENNA_B); |
| 1768 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_RX_DEFAULT, |
| 1769 |
ANTENNA_B); |
| 1770 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_FRAME_TYPE, 0); |
| 1771 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_DYN_TXAGC, 0); |
| 1772 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_HARDWARE_RADIO, 0); |
| 1773 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_RF_TYPE, RF5226); |
| 1774 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_ANTENNA, word); |
| 1775 |
rt2x00_eeprom_dbg(rt2x00dev, "Antenna: 0x%04x\n", word); |
| 1776 |
} |
| 1777 |
|
| 1778 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC); |
| 1779 |
if (word == 0xffff) { |
| 1780 |
rt2x00_set_field16(&word, EEPROM_NIC_EXTERNAL_LNA, 0); |
| 1781 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_NIC, word); |
| 1782 |
rt2x00_eeprom_dbg(rt2x00dev, "NIC: 0x%04x\n", word); |
| 1783 |
} |
| 1784 |
|
| 1785 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_LED); |
| 1786 |
if (word == 0xffff) { |
| 1787 |
rt2x00_set_field16(&word, EEPROM_LED_POLARITY_RDY_G, 0); |
| 1788 |
rt2x00_set_field16(&word, EEPROM_LED_POLARITY_RDY_A, 0); |
| 1789 |
rt2x00_set_field16(&word, EEPROM_LED_POLARITY_ACT, 0); |
| 1790 |
rt2x00_set_field16(&word, EEPROM_LED_POLARITY_GPIO_0, 0); |
| 1791 |
rt2x00_set_field16(&word, EEPROM_LED_POLARITY_GPIO_1, 0); |
| 1792 |
rt2x00_set_field16(&word, EEPROM_LED_POLARITY_GPIO_2, 0); |
| 1793 |
rt2x00_set_field16(&word, EEPROM_LED_POLARITY_GPIO_3, 0); |
| 1794 |
rt2x00_set_field16(&word, EEPROM_LED_POLARITY_GPIO_4, 0); |
| 1795 |
rt2x00_set_field16(&word, EEPROM_LED_LED_MODE, |
| 1796 |
LED_MODE_DEFAULT); |
| 1797 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_LED, word); |
| 1798 |
rt2x00_eeprom_dbg(rt2x00dev, "Led: 0x%04x\n", word); |
| 1799 |
} |
| 1800 |
|
| 1801 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_FREQ); |
| 1802 |
if (word == 0xffff) { |
| 1803 |
rt2x00_set_field16(&word, EEPROM_FREQ_OFFSET, 0); |
| 1804 |
rt2x00_set_field16(&word, EEPROM_FREQ_SEQ, 0); |
| 1805 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_FREQ, word); |
| 1806 |
rt2x00_eeprom_dbg(rt2x00dev, "Freq: 0x%04x\n", word); |
| 1807 |
} |
| 1808 |
|
| 1809 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_BG); |
| 1810 |
if (word == 0xffff) { |
| 1811 |
rt2x00_set_field16(&word, EEPROM_RSSI_OFFSET_BG_1, 0); |
| 1812 |
rt2x00_set_field16(&word, EEPROM_RSSI_OFFSET_BG_2, 0); |
| 1813 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_RSSI_OFFSET_BG, word); |
| 1814 |
rt2x00_eeprom_dbg(rt2x00dev, "RSSI OFFSET BG: 0x%04x\n", word); |
| 1815 |
} else { |
| 1816 |
value = rt2x00_get_field16(word, EEPROM_RSSI_OFFSET_BG_1); |
| 1817 |
if (value < -10 || value > 10) |
| 1818 |
rt2x00_set_field16(&word, EEPROM_RSSI_OFFSET_BG_1, 0); |
| 1819 |
value = rt2x00_get_field16(word, EEPROM_RSSI_OFFSET_BG_2); |
| 1820 |
if (value < -10 || value > 10) |
| 1821 |
rt2x00_set_field16(&word, EEPROM_RSSI_OFFSET_BG_2, 0); |
| 1822 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_RSSI_OFFSET_BG, word); |
| 1823 |
} |
| 1824 |
|
| 1825 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_A); |
| 1826 |
if (word == 0xffff) { |
| 1827 |
rt2x00_set_field16(&word, EEPROM_RSSI_OFFSET_A_1, 0); |
| 1828 |
rt2x00_set_field16(&word, EEPROM_RSSI_OFFSET_A_2, 0); |
| 1829 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_RSSI_OFFSET_A, word); |
| 1830 |
rt2x00_eeprom_dbg(rt2x00dev, "RSSI OFFSET A: 0x%04x\n", word); |
| 1831 |
} else { |
| 1832 |
value = rt2x00_get_field16(word, EEPROM_RSSI_OFFSET_A_1); |
| 1833 |
if (value < -10 || value > 10) |
| 1834 |
rt2x00_set_field16(&word, EEPROM_RSSI_OFFSET_A_1, 0); |
| 1835 |
value = rt2x00_get_field16(word, EEPROM_RSSI_OFFSET_A_2); |
| 1836 |
if (value < -10 || value > 10) |
| 1837 |
rt2x00_set_field16(&word, EEPROM_RSSI_OFFSET_A_2, 0); |
| 1838 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_RSSI_OFFSET_A, word); |
| 1839 |
} |
| 1840 |
|
| 1841 |
return 0; |
| 1842 |
} |
| 1843 |
|
| 1844 |
static int rt73usb_init_eeprom(struct rt2x00_dev *rt2x00dev) |
| 1845 |
{ |
| 1846 |
u32 reg; |
| 1847 |
u16 value; |
| 1848 |
u16 eeprom; |
| 1849 |
|
| 1850 |
/* |
| 1851 |
* Read EEPROM word for configuration. |
| 1852 |
*/ |
| 1853 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA); |
| 1854 |
|
| 1855 |
/* |
| 1856 |
* Identify RF chipset. |
| 1857 |
*/ |
| 1858 |
value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RF_TYPE); |
| 1859 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR0); |
| 1860 |
rt2x00_set_chip(rt2x00dev, rt2x00_get_field32(reg, MAC_CSR0_CHIPSET), |
| 1861 |
value, rt2x00_get_field32(reg, MAC_CSR0_REVISION)); |
| 1862 |
|
| 1863 |
if (!rt2x00_rt(rt2x00dev, RT2573) || (rt2x00_rev(rt2x00dev) == 0)) { |
| 1864 |
rt2x00_err(rt2x00dev, "Invalid RT chipset detected\n"); |
| 1865 |
return -ENODEV; |
| 1866 |
} |
| 1867 |
|
| 1868 |
if (!rt2x00_rf(rt2x00dev, RF5226) && |
| 1869 |
!rt2x00_rf(rt2x00dev, RF2528) && |
| 1870 |
!rt2x00_rf(rt2x00dev, RF5225) && |
| 1871 |
!rt2x00_rf(rt2x00dev, RF2527)) { |
| 1872 |
rt2x00_err(rt2x00dev, "Invalid RF chipset detected\n"); |
| 1873 |
return -ENODEV; |
| 1874 |
} |
| 1875 |
|
| 1876 |
/* |
| 1877 |
* Identify default antenna configuration. |
| 1878 |
*/ |
| 1879 |
rt2x00dev->default_ant.tx = |
| 1880 |
rt2x00_get_field16(eeprom, EEPROM_ANTENNA_TX_DEFAULT); |
| 1881 |
rt2x00dev->default_ant.rx = |
| 1882 |
rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RX_DEFAULT); |
| 1883 |
|
| 1884 |
/* |
| 1885 |
* Read the Frame type. |
| 1886 |
*/ |
| 1887 |
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_FRAME_TYPE)) |
| 1888 |
__set_bit(CAPABILITY_FRAME_TYPE, &rt2x00dev->cap_flags); |
| 1889 |
|
| 1890 |
/* |
| 1891 |
* Detect if this device has an hardware controlled radio. |
| 1892 |
*/ |
| 1893 |
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_HARDWARE_RADIO)) |
| 1894 |
__set_bit(CAPABILITY_HW_BUTTON, &rt2x00dev->cap_flags); |
| 1895 |
|
| 1896 |
/* |
| 1897 |
* Read frequency offset. |
| 1898 |
*/ |
| 1899 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_FREQ); |
| 1900 |
rt2x00dev->freq_offset = rt2x00_get_field16(eeprom, EEPROM_FREQ_OFFSET); |
| 1901 |
|
| 1902 |
/* |
| 1903 |
* Read external LNA informations. |
| 1904 |
*/ |
| 1905 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC); |
| 1906 |
|
| 1907 |
if (rt2x00_get_field16(eeprom, EEPROM_NIC_EXTERNAL_LNA)) { |
| 1908 |
__set_bit(CAPABILITY_EXTERNAL_LNA_A, &rt2x00dev->cap_flags); |
| 1909 |
__set_bit(CAPABILITY_EXTERNAL_LNA_BG, &rt2x00dev->cap_flags); |
| 1910 |
} |
| 1911 |
|
| 1912 |
/* |
| 1913 |
* Store led settings, for correct led behaviour. |
| 1914 |
*/ |
| 1915 |
#ifdef CONFIG_RT2X00_LIB_LEDS |
| 1916 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_LED); |
| 1917 |
|
| 1918 |
rt73usb_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO); |
| 1919 |
rt73usb_init_led(rt2x00dev, &rt2x00dev->led_assoc, LED_TYPE_ASSOC); |
| 1920 |
if (value == LED_MODE_SIGNAL_STRENGTH) |
| 1921 |
rt73usb_init_led(rt2x00dev, &rt2x00dev->led_qual, |
| 1922 |
LED_TYPE_QUALITY); |
| 1923 |
|
| 1924 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_LED_MODE, value); |
| 1925 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_GPIO_0, |
| 1926 |
rt2x00_get_field16(eeprom, |
| 1927 |
EEPROM_LED_POLARITY_GPIO_0)); |
| 1928 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_GPIO_1, |
| 1929 |
rt2x00_get_field16(eeprom, |
| 1930 |
EEPROM_LED_POLARITY_GPIO_1)); |
| 1931 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_GPIO_2, |
| 1932 |
rt2x00_get_field16(eeprom, |
| 1933 |
EEPROM_LED_POLARITY_GPIO_2)); |
| 1934 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_GPIO_3, |
| 1935 |
rt2x00_get_field16(eeprom, |
| 1936 |
EEPROM_LED_POLARITY_GPIO_3)); |
| 1937 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_GPIO_4, |
| 1938 |
rt2x00_get_field16(eeprom, |
| 1939 |
EEPROM_LED_POLARITY_GPIO_4)); |
| 1940 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_ACT, |
| 1941 |
rt2x00_get_field16(eeprom, EEPROM_LED_POLARITY_ACT)); |
| 1942 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_READY_BG, |
| 1943 |
rt2x00_get_field16(eeprom, |
| 1944 |
EEPROM_LED_POLARITY_RDY_G)); |
| 1945 |
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_READY_A, |
| 1946 |
rt2x00_get_field16(eeprom, |
| 1947 |
EEPROM_LED_POLARITY_RDY_A)); |
| 1948 |
#endif /* CONFIG_RT2X00_LIB_LEDS */ |
| 1949 |
|
| 1950 |
return 0; |
| 1951 |
} |
| 1952 |
|
| 1953 |
/* |
| 1954 |
* RF value list for RF2528 |
| 1955 |
* Supports: 2.4 GHz |
| 1956 |
*/ |
| 1957 |
static const struct rf_channel rf_vals_bg_2528[] = { |
| 1958 |
{ 1, 0x00002c0c, 0x00000786, 0x00068255, 0x000fea0b }, |
| 1959 |
{ 2, 0x00002c0c, 0x00000786, 0x00068255, 0x000fea1f }, |
| 1960 |
{ 3, 0x00002c0c, 0x0000078a, 0x00068255, 0x000fea0b }, |
| 1961 |
{ 4, 0x00002c0c, 0x0000078a, 0x00068255, 0x000fea1f }, |
| 1962 |
{ 5, 0x00002c0c, 0x0000078e, 0x00068255, 0x000fea0b }, |
| 1963 |
{ 6, 0x00002c0c, 0x0000078e, 0x00068255, 0x000fea1f }, |
| 1964 |
{ 7, 0x00002c0c, 0x00000792, 0x00068255, 0x000fea0b }, |
| 1965 |
{ 8, 0x00002c0c, 0x00000792, 0x00068255, 0x000fea1f }, |
| 1966 |
{ 9, 0x00002c0c, 0x00000796, 0x00068255, 0x000fea0b }, |
| 1967 |
{ 10, 0x00002c0c, 0x00000796, 0x00068255, 0x000fea1f }, |
| 1968 |
{ 11, 0x00002c0c, 0x0000079a, 0x00068255, 0x000fea0b }, |
| 1969 |
{ 12, 0x00002c0c, 0x0000079a, 0x00068255, 0x000fea1f }, |
| 1970 |
{ 13, 0x00002c0c, 0x0000079e, 0x00068255, 0x000fea0b }, |
| 1971 |
{ 14, 0x00002c0c, 0x000007a2, 0x00068255, 0x000fea13 }, |
| 1972 |
}; |
| 1973 |
|
| 1974 |
/* |
| 1975 |
* RF value list for RF5226 |
| 1976 |
* Supports: 2.4 GHz & 5.2 GHz |
| 1977 |
*/ |
| 1978 |
static const struct rf_channel rf_vals_5226[] = { |
| 1979 |
{ 1, 0x00002c0c, 0x00000786, 0x00068255, 0x000fea0b }, |
| 1980 |
{ 2, 0x00002c0c, 0x00000786, 0x00068255, 0x000fea1f }, |
| 1981 |
{ 3, 0x00002c0c, 0x0000078a, 0x00068255, 0x000fea0b }, |
| 1982 |
{ 4, 0x00002c0c, 0x0000078a, 0x00068255, 0x000fea1f }, |
| 1983 |
{ 5, 0x00002c0c, 0x0000078e, 0x00068255, 0x000fea0b }, |
| 1984 |
{ 6, 0x00002c0c, 0x0000078e, 0x00068255, 0x000fea1f }, |
| 1985 |
{ 7, 0x00002c0c, 0x00000792, 0x00068255, 0x000fea0b }, |
| 1986 |
{ 8, 0x00002c0c, 0x00000792, 0x00068255, 0x000fea1f }, |
| 1987 |
{ 9, 0x00002c0c, 0x00000796, 0x00068255, 0x000fea0b }, |
| 1988 |
{ 10, 0x00002c0c, 0x00000796, 0x00068255, 0x000fea1f }, |
| 1989 |
{ 11, 0x00002c0c, 0x0000079a, 0x00068255, 0x000fea0b }, |
| 1990 |
{ 12, 0x00002c0c, 0x0000079a, 0x00068255, 0x000fea1f }, |
| 1991 |
{ 13, 0x00002c0c, 0x0000079e, 0x00068255, 0x000fea0b }, |
| 1992 |
{ 14, 0x00002c0c, 0x000007a2, 0x00068255, 0x000fea13 }, |
| 1993 |
|
| 1994 |
/* 802.11 UNI / HyperLan 2 */ |
| 1995 |
{ 36, 0x00002c0c, 0x0000099a, 0x00098255, 0x000fea23 }, |
| 1996 |
{ 40, 0x00002c0c, 0x000009a2, 0x00098255, 0x000fea03 }, |
| 1997 |
{ 44, 0x00002c0c, 0x000009a6, 0x00098255, 0x000fea0b }, |
| 1998 |
{ 48, 0x00002c0c, 0x000009aa, 0x00098255, 0x000fea13 }, |
| 1999 |
{ 52, 0x00002c0c, 0x000009ae, 0x00098255, 0x000fea1b }, |
| 2000 |
{ 56, 0x00002c0c, 0x000009b2, 0x00098255, 0x000fea23 }, |
| 2001 |
{ 60, 0x00002c0c, 0x000009ba, 0x00098255, 0x000fea03 }, |
| 2002 |
{ 64, 0x00002c0c, 0x000009be, 0x00098255, 0x000fea0b }, |
| 2003 |
|
| 2004 |
/* 802.11 HyperLan 2 */ |
| 2005 |
{ 100, 0x00002c0c, 0x00000a2a, 0x000b8255, 0x000fea03 }, |
| 2006 |
{ 104, 0x00002c0c, 0x00000a2e, 0x000b8255, 0x000fea0b }, |
| 2007 |
{ 108, 0x00002c0c, 0x00000a32, 0x000b8255, 0x000fea13 }, |
| 2008 |
{ 112, 0x00002c0c, 0x00000a36, 0x000b8255, 0x000fea1b }, |
| 2009 |
{ 116, 0x00002c0c, 0x00000a3a, 0x000b8255, 0x000fea23 }, |
| 2010 |
{ 120, 0x00002c0c, 0x00000a82, 0x000b8255, 0x000fea03 }, |
| 2011 |
{ 124, 0x00002c0c, 0x00000a86, 0x000b8255, 0x000fea0b }, |
| 2012 |
{ 128, 0x00002c0c, 0x00000a8a, 0x000b8255, 0x000fea13 }, |
| 2013 |
{ 132, 0x00002c0c, 0x00000a8e, 0x000b8255, 0x000fea1b }, |
| 2014 |
{ 136, 0x00002c0c, 0x00000a92, 0x000b8255, 0x000fea23 }, |
| 2015 |
|
| 2016 |
/* 802.11 UNII */ |
| 2017 |
{ 140, 0x00002c0c, 0x00000a9a, 0x000b8255, 0x000fea03 }, |
| 2018 |
{ 149, 0x00002c0c, 0x00000aa2, 0x000b8255, 0x000fea1f }, |
| 2019 |
{ 153, 0x00002c0c, 0x00000aa6, 0x000b8255, 0x000fea27 }, |
| 2020 |
{ 157, 0x00002c0c, 0x00000aae, 0x000b8255, 0x000fea07 }, |
| 2021 |
{ 161, 0x00002c0c, 0x00000ab2, 0x000b8255, 0x000fea0f }, |
| 2022 |
{ 165, 0x00002c0c, 0x00000ab6, 0x000b8255, 0x000fea17 }, |
| 2023 |
|
| 2024 |
/* MMAC(Japan)J52 ch 34,38,42,46 */ |
| 2025 |
{ 34, 0x00002c0c, 0x0008099a, 0x000da255, 0x000d3a0b }, |
| 2026 |
{ 38, 0x00002c0c, 0x0008099e, 0x000da255, 0x000d3a13 }, |
| 2027 |
{ 42, 0x00002c0c, 0x000809a2, 0x000da255, 0x000d3a1b }, |
| 2028 |
{ 46, 0x00002c0c, 0x000809a6, 0x000da255, 0x000d3a23 }, |
| 2029 |
}; |
| 2030 |
|
| 2031 |
/* |
| 2032 |
* RF value list for RF5225 & RF2527 |
| 2033 |
* Supports: 2.4 GHz & 5.2 GHz |
| 2034 |
*/ |
| 2035 |
static const struct rf_channel rf_vals_5225_2527[] = { |
| 2036 |
{ 1, 0x00002ccc, 0x00004786, 0x00068455, 0x000ffa0b }, |
| 2037 |
{ 2, 0x00002ccc, 0x00004786, 0x00068455, 0x000ffa1f }, |
| 2038 |
{ 3, 0x00002ccc, 0x0000478a, 0x00068455, 0x000ffa0b }, |
| 2039 |
{ 4, 0x00002ccc, 0x0000478a, 0x00068455, 0x000ffa1f }, |
| 2040 |
{ 5, 0x00002ccc, 0x0000478e, 0x00068455, 0x000ffa0b }, |
| 2041 |
{ 6, 0x00002ccc, 0x0000478e, 0x00068455, 0x000ffa1f }, |
| 2042 |
{ 7, 0x00002ccc, 0x00004792, 0x00068455, 0x000ffa0b }, |
| 2043 |
{ 8, 0x00002ccc, 0x00004792, 0x00068455, 0x000ffa1f }, |
| 2044 |
{ 9, 0x00002ccc, 0x00004796, 0x00068455, 0x000ffa0b }, |
| 2045 |
{ 10, 0x00002ccc, 0x00004796, 0x00068455, 0x000ffa1f }, |
| 2046 |
{ 11, 0x00002ccc, 0x0000479a, 0x00068455, 0x000ffa0b }, |
| 2047 |
{ 12, 0x00002ccc, 0x0000479a, 0x00068455, 0x000ffa1f }, |
| 2048 |
{ 13, 0x00002ccc, 0x0000479e, 0x00068455, 0x000ffa0b }, |
| 2049 |
{ 14, 0x00002ccc, 0x000047a2, 0x00068455, 0x000ffa13 }, |
| 2050 |
|
| 2051 |
/* 802.11 UNI / HyperLan 2 */ |
| 2052 |
{ 36, 0x00002ccc, 0x0000499a, 0x0009be55, 0x000ffa23 }, |
| 2053 |
{ 40, 0x00002ccc, 0x000049a2, 0x0009be55, 0x000ffa03 }, |
| 2054 |
{ 44, 0x00002ccc, 0x000049a6, 0x0009be55, 0x000ffa0b }, |
| 2055 |
{ 48, 0x00002ccc, 0x000049aa, 0x0009be55, 0x000ffa13 }, |
| 2056 |
{ 52, 0x00002ccc, 0x000049ae, 0x0009ae55, 0x000ffa1b }, |
| 2057 |
{ 56, 0x00002ccc, 0x000049b2, 0x0009ae55, 0x000ffa23 }, |
| 2058 |
{ 60, 0x00002ccc, 0x000049ba, 0x0009ae55, 0x000ffa03 }, |
| 2059 |
{ 64, 0x00002ccc, 0x000049be, 0x0009ae55, 0x000ffa0b }, |
| 2060 |
|
| 2061 |
/* 802.11 HyperLan 2 */ |
| 2062 |
{ 100, 0x00002ccc, 0x00004a2a, 0x000bae55, 0x000ffa03 }, |
| 2063 |
{ 104, 0x00002ccc, 0x00004a2e, 0x000bae55, 0x000ffa0b }, |
| 2064 |
{ 108, 0x00002ccc, 0x00004a32, 0x000bae55, 0x000ffa13 }, |
| 2065 |
{ 112, 0x00002ccc, 0x00004a36, 0x000bae55, 0x000ffa1b }, |
| 2066 |
{ 116, 0x00002ccc, 0x00004a3a, 0x000bbe55, 0x000ffa23 }, |
| 2067 |
{ 120, 0x00002ccc, 0x00004a82, 0x000bbe55, 0x000ffa03 }, |
| 2068 |
{ 124, 0x00002ccc, 0x00004a86, 0x000bbe55, 0x000ffa0b }, |
| 2069 |
{ 128, 0x00002ccc, 0x00004a8a, 0x000bbe55, 0x000ffa13 }, |
| 2070 |
{ 132, 0x00002ccc, 0x00004a8e, 0x000bbe55, 0x000ffa1b }, |
| 2071 |
{ 136, 0x00002ccc, 0x00004a92, 0x000bbe55, 0x000ffa23 }, |
| 2072 |
|
| 2073 |
/* 802.11 UNII */ |
| 2074 |
{ 140, 0x00002ccc, 0x00004a9a, 0x000bbe55, 0x000ffa03 }, |
| 2075 |
{ 149, 0x00002ccc, 0x00004aa2, 0x000bbe55, 0x000ffa1f }, |
| 2076 |
{ 153, 0x00002ccc, 0x00004aa6, 0x000bbe55, 0x000ffa27 }, |
| 2077 |
{ 157, 0x00002ccc, 0x00004aae, 0x000bbe55, 0x000ffa07 }, |
| 2078 |
{ 161, 0x00002ccc, 0x00004ab2, 0x000bbe55, 0x000ffa0f }, |
| 2079 |
{ 165, 0x00002ccc, 0x00004ab6, 0x000bbe55, 0x000ffa17 }, |
| 2080 |
|
| 2081 |
/* MMAC(Japan)J52 ch 34,38,42,46 */ |
| 2082 |
{ 34, 0x00002ccc, 0x0000499a, 0x0009be55, 0x000ffa0b }, |
| 2083 |
{ 38, 0x00002ccc, 0x0000499e, 0x0009be55, 0x000ffa13 }, |
| 2084 |
{ 42, 0x00002ccc, 0x000049a2, 0x0009be55, 0x000ffa1b }, |
| 2085 |
{ 46, 0x00002ccc, 0x000049a6, 0x0009be55, 0x000ffa23 }, |
| 2086 |
}; |
| 2087 |
|
| 2088 |
|
| 2089 |
static int rt73usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev) |
| 2090 |
{ |
| 2091 |
struct hw_mode_spec *spec = &rt2x00dev->spec; |
| 2092 |
struct channel_info *info; |
| 2093 |
u8 *tx_power; |
| 2094 |
unsigned int i; |
| 2095 |
|
| 2096 |
/* |
| 2097 |
* Initialize all hw fields. |
| 2098 |
* |
| 2099 |
* Don't set IEEE80211_HOST_BROADCAST_PS_BUFFERING unless we are |
| 2100 |
* capable of sending the buffered frames out after the DTIM |
| 2101 |
* transmission using rt2x00lib_beacondone. This will send out |
| 2102 |
* multicast and broadcast traffic immediately instead of buffering it |
| 2103 |
* infinitly and thus dropping it after some time. |
| 2104 |
*/ |
| 2105 |
ieee80211_hw_set(rt2x00dev->hw, PS_NULLFUNC_STACK); |
| 2106 |
ieee80211_hw_set(rt2x00dev->hw, SIGNAL_DBM); |
| 2107 |
ieee80211_hw_set(rt2x00dev->hw, SUPPORTS_PS); |
| 2108 |
|
| 2109 |
SET_IEEE80211_DEV(rt2x00dev->hw, rt2x00dev->dev); |
| 2110 |
SET_IEEE80211_PERM_ADDR(rt2x00dev->hw, |
| 2111 |
rt2x00_eeprom_addr(rt2x00dev, |
| 2112 |
EEPROM_MAC_ADDR_0)); |
| 2113 |
|
| 2114 |
/* |
| 2115 |
* Initialize hw_mode information. |
| 2116 |
*/ |
| 2117 |
spec->supported_bands = SUPPORT_BAND_2GHZ; |
| 2118 |
spec->supported_rates = SUPPORT_RATE_CCK | SUPPORT_RATE_OFDM; |
| 2119 |
|
| 2120 |
if (rt2x00_rf(rt2x00dev, RF2528)) { |
| 2121 |
spec->num_channels = ARRAY_SIZE(rf_vals_bg_2528); |
| 2122 |
spec->channels = rf_vals_bg_2528; |
| 2123 |
} else if (rt2x00_rf(rt2x00dev, RF5226)) { |
| 2124 |
spec->supported_bands |= SUPPORT_BAND_5GHZ; |
| 2125 |
spec->num_channels = ARRAY_SIZE(rf_vals_5226); |
| 2126 |
spec->channels = rf_vals_5226; |
| 2127 |
} else if (rt2x00_rf(rt2x00dev, RF2527)) { |
| 2128 |
spec->num_channels = 14; |
| 2129 |
spec->channels = rf_vals_5225_2527; |
| 2130 |
} else if (rt2x00_rf(rt2x00dev, RF5225)) { |
| 2131 |
spec->supported_bands |= SUPPORT_BAND_5GHZ; |
| 2132 |
spec->num_channels = ARRAY_SIZE(rf_vals_5225_2527); |
| 2133 |
spec->channels = rf_vals_5225_2527; |
| 2134 |
} |
| 2135 |
|
| 2136 |
/* |
| 2137 |
* Create channel information array |
| 2138 |
*/ |
| 2139 |
info = kzalloc_objs(*info, spec->num_channels); |
| 2140 |
if (!info) |
| 2141 |
return -ENOMEM; |
| 2142 |
|
| 2143 |
spec->channels_info = info; |
| 2144 |
|
| 2145 |
tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_G_START); |
| 2146 |
for (i = 0; i < 14; i++) { |
| 2147 |
info[i].max_power = MAX_TXPOWER; |
| 2148 |
info[i].default_power1 = TXPOWER_FROM_DEV(tx_power[i]); |
| 2149 |
} |
| 2150 |
|
| 2151 |
if (spec->num_channels > 14) { |
| 2152 |
tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_A_START); |
| 2153 |
for (i = 14; i < spec->num_channels; i++) { |
| 2154 |
info[i].max_power = MAX_TXPOWER; |
| 2155 |
info[i].default_power1 = |
| 2156 |
TXPOWER_FROM_DEV(tx_power[i - 14]); |
| 2157 |
} |
| 2158 |
} |
| 2159 |
|
| 2160 |
return 0; |
| 2161 |
} |
| 2162 |
|
| 2163 |
static int rt73usb_probe_hw(struct rt2x00_dev *rt2x00dev) |
| 2164 |
{ |
| 2165 |
int retval; |
| 2166 |
u32 reg; |
| 2167 |
|
| 2168 |
/* |
| 2169 |
* Allocate eeprom data. |
| 2170 |
*/ |
| 2171 |
retval = rt73usb_validate_eeprom(rt2x00dev); |
| 2172 |
if (retval) |
| 2173 |
return retval; |
| 2174 |
|
| 2175 |
retval = rt73usb_init_eeprom(rt2x00dev); |
| 2176 |
if (retval) |
| 2177 |
return retval; |
| 2178 |
|
| 2179 |
/* |
| 2180 |
* Enable rfkill polling by setting GPIO direction of the |
| 2181 |
* rfkill switch GPIO pin correctly. |
| 2182 |
*/ |
| 2183 |
reg = rt2x00usb_register_read(rt2x00dev, MAC_CSR13); |
| 2184 |
rt2x00_set_field32(®, MAC_CSR13_DIR7, 0); |
| 2185 |
rt2x00usb_register_write(rt2x00dev, MAC_CSR13, reg); |
| 2186 |
|
| 2187 |
/* |
| 2188 |
* Initialize hw specifications. |
| 2189 |
*/ |
| 2190 |
retval = rt73usb_probe_hw_mode(rt2x00dev); |
| 2191 |
if (retval) |
| 2192 |
return retval; |
| 2193 |
|
| 2194 |
/* |
| 2195 |
* This device has multiple filters for control frames, |
| 2196 |
* but has no a separate filter for PS Poll frames. |
| 2197 |
*/ |
| 2198 |
__set_bit(CAPABILITY_CONTROL_FILTERS, &rt2x00dev->cap_flags); |
| 2199 |
|
| 2200 |
/* |
| 2201 |
* This device requires firmware. |
| 2202 |
*/ |
| 2203 |
__set_bit(REQUIRE_FIRMWARE, &rt2x00dev->cap_flags); |
| 2204 |
if (!modparam_nohwcrypt) |
| 2205 |
__set_bit(CAPABILITY_HW_CRYPTO, &rt2x00dev->cap_flags); |
| 2206 |
__set_bit(CAPABILITY_LINK_TUNING, &rt2x00dev->cap_flags); |
| 2207 |
__set_bit(REQUIRE_PS_AUTOWAKE, &rt2x00dev->cap_flags); |
| 2208 |
|
| 2209 |
/* |
| 2210 |
* Set the rssi offset. |
| 2211 |
*/ |
| 2212 |
rt2x00dev->rssi_offset = DEFAULT_RSSI_OFFSET; |
| 2213 |
|
| 2214 |
return 0; |
| 2215 |
} |
| 2216 |
|
| 2217 |
/* |
| 2218 |
* IEEE80211 stack callback functions. |
| 2219 |
*/ |
| 2220 |
static int rt73usb_conf_tx(struct ieee80211_hw *hw, |
| 2221 |
struct ieee80211_vif *vif, |
| 2222 |
unsigned int link_id, u16 queue_idx, |
| 2223 |
const struct ieee80211_tx_queue_params *params) |
| 2224 |
{ |
| 2225 |
struct rt2x00_dev *rt2x00dev = hw->priv; |
| 2226 |
struct data_queue *queue; |
| 2227 |
struct rt2x00_field32 field; |
| 2228 |
int retval; |
| 2229 |
u32 reg; |
| 2230 |
u32 offset; |
| 2231 |
|
| 2232 |
/* |
| 2233 |
* First pass the configuration through rt2x00lib, that will |
| 2234 |
* update the queue settings and validate the input. After that |
| 2235 |
* we are free to update the registers based on the value |
| 2236 |
* in the queue parameter. |
| 2237 |
*/ |
| 2238 |
retval = rt2x00mac_conf_tx(hw, vif, link_id, queue_idx, params); |
| 2239 |
if (retval) |
| 2240 |
return retval; |
| 2241 |
|
| 2242 |
/* |
| 2243 |
* We only need to perform additional register initialization |
| 2244 |
* for WMM queues/ |
| 2245 |
*/ |
| 2246 |
if (queue_idx >= 4) |
| 2247 |
return 0; |
| 2248 |
|
| 2249 |
queue = rt2x00queue_get_tx_queue(rt2x00dev, queue_idx); |
| 2250 |
|
| 2251 |
/* Update WMM TXOP register */ |
| 2252 |
offset = AC_TXOP_CSR0 + (sizeof(u32) * (!!(queue_idx & 2))); |
| 2253 |
field.bit_offset = (queue_idx & 1) * 16; |
| 2254 |
field.bit_mask = 0xffff << field.bit_offset; |
| 2255 |
|
| 2256 |
reg = rt2x00usb_register_read(rt2x00dev, offset); |
| 2257 |
rt2x00_set_field32(®, field, queue->txop); |
| 2258 |
rt2x00usb_register_write(rt2x00dev, offset, reg); |
| 2259 |
|
| 2260 |
/* Update WMM registers */ |
| 2261 |
field.bit_offset = queue_idx * 4; |
| 2262 |
field.bit_mask = 0xf << field.bit_offset; |
| 2263 |
|
| 2264 |
reg = rt2x00usb_register_read(rt2x00dev, AIFSN_CSR); |
| 2265 |
rt2x00_set_field32(®, field, queue->aifs); |
| 2266 |
rt2x00usb_register_write(rt2x00dev, AIFSN_CSR, reg); |
| 2267 |
|
| 2268 |
reg = rt2x00usb_register_read(rt2x00dev, CWMIN_CSR); |
| 2269 |
rt2x00_set_field32(®, field, queue->cw_min); |
| 2270 |
rt2x00usb_register_write(rt2x00dev, CWMIN_CSR, reg); |
| 2271 |
|
| 2272 |
reg = rt2x00usb_register_read(rt2x00dev, CWMAX_CSR); |
| 2273 |
rt2x00_set_field32(®, field, queue->cw_max); |
| 2274 |
rt2x00usb_register_write(rt2x00dev, CWMAX_CSR, reg); |
| 2275 |
|
| 2276 |
return 0; |
| 2277 |
} |
| 2278 |
|
| 2279 |
static u64 rt73usb_get_tsf(struct ieee80211_hw *hw, struct ieee80211_vif *vif) |
| 2280 |
{ |
| 2281 |
struct rt2x00_dev *rt2x00dev = hw->priv; |
| 2282 |
u64 tsf; |
| 2283 |
u32 reg; |
| 2284 |
|
| 2285 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR13); |
| 2286 |
tsf = (u64) rt2x00_get_field32(reg, TXRX_CSR13_HIGH_TSFTIMER) << 32; |
| 2287 |
reg = rt2x00usb_register_read(rt2x00dev, TXRX_CSR12); |
| 2288 |
tsf |= rt2x00_get_field32(reg, TXRX_CSR12_LOW_TSFTIMER); |
| 2289 |
|
| 2290 |
return tsf; |
| 2291 |
} |
| 2292 |
|
| 2293 |
static const struct ieee80211_ops rt73usb_mac80211_ops = { |
| 2294 |
.add_chanctx = ieee80211_emulate_add_chanctx, |
| 2295 |
.remove_chanctx = ieee80211_emulate_remove_chanctx, |
| 2296 |
.change_chanctx = ieee80211_emulate_change_chanctx, |
| 2297 |
.switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx, |
| 2298 |
.tx = rt2x00mac_tx, |
| 2299 |
.wake_tx_queue = ieee80211_handle_wake_tx_queue, |
| 2300 |
.start = rt2x00mac_start, |
| 2301 |
.stop = rt2x00mac_stop, |
| 2302 |
.add_interface = rt2x00mac_add_interface, |
| 2303 |
.remove_interface = rt2x00mac_remove_interface, |
| 2304 |
.config = rt2x00mac_config, |
| 2305 |
.configure_filter = rt2x00mac_configure_filter, |
| 2306 |
.set_tim = rt2x00mac_set_tim, |
| 2307 |
.set_key = rt2x00mac_set_key, |
| 2308 |
.sw_scan_start = rt2x00mac_sw_scan_start, |
| 2309 |
.sw_scan_complete = rt2x00mac_sw_scan_complete, |
| 2310 |
.get_stats = rt2x00mac_get_stats, |
| 2311 |
.bss_info_changed = rt2x00mac_bss_info_changed, |
| 2312 |
.conf_tx = rt73usb_conf_tx, |
| 2313 |
.get_tsf = rt73usb_get_tsf, |
| 2314 |
.rfkill_poll = rt2x00mac_rfkill_poll, |
| 2315 |
.flush = rt2x00mac_flush, |
| 2316 |
.set_antenna = rt2x00mac_set_antenna, |
| 2317 |
.get_antenna = rt2x00mac_get_antenna, |
| 2318 |
.get_ringparam = rt2x00mac_get_ringparam, |
| 2319 |
.tx_frames_pending = rt2x00mac_tx_frames_pending, |
| 2320 |
}; |
| 2321 |
|
| 2322 |
static const struct rt2x00lib_ops rt73usb_rt2x00_ops = { |
| 2323 |
.probe_hw = rt73usb_probe_hw, |
| 2324 |
.get_firmware_name = rt73usb_get_firmware_name, |
| 2325 |
.check_firmware = rt73usb_check_firmware, |
| 2326 |
.load_firmware = rt73usb_load_firmware, |
| 2327 |
.initialize = rt2x00usb_initialize, |
| 2328 |
.uninitialize = rt2x00usb_uninitialize, |
| 2329 |
.clear_entry = rt2x00usb_clear_entry, |
| 2330 |
.set_device_state = rt73usb_set_device_state, |
| 2331 |
.rfkill_poll = rt73usb_rfkill_poll, |
| 2332 |
.link_stats = rt73usb_link_stats, |
| 2333 |
.reset_tuner = rt73usb_reset_tuner, |
| 2334 |
.link_tuner = rt73usb_link_tuner, |
| 2335 |
.watchdog = rt2x00usb_watchdog, |
| 2336 |
.start_queue = rt73usb_start_queue, |
| 2337 |
.kick_queue = rt2x00usb_kick_queue, |
| 2338 |
.stop_queue = rt73usb_stop_queue, |
| 2339 |
.flush_queue = rt2x00usb_flush_queue, |
| 2340 |
.write_tx_desc = rt73usb_write_tx_desc, |
| 2341 |
.write_beacon = rt73usb_write_beacon, |
| 2342 |
.clear_beacon = rt73usb_clear_beacon, |
| 2343 |
.get_tx_data_len = rt73usb_get_tx_data_len, |
| 2344 |
.fill_rxdone = rt73usb_fill_rxdone, |
| 2345 |
.config_shared_key = rt73usb_config_shared_key, |
| 2346 |
.config_pairwise_key = rt73usb_config_pairwise_key, |
| 2347 |
.config_filter = rt73usb_config_filter, |
| 2348 |
.config_intf = rt73usb_config_intf, |
| 2349 |
.config_erp = rt73usb_config_erp, |
| 2350 |
.config_ant = rt73usb_config_ant, |
| 2351 |
.config = rt73usb_config, |
| 2352 |
}; |
| 2353 |
|
| 2354 |
static void rt73usb_queue_init(struct data_queue *queue) |
| 2355 |
{ |
| 2356 |
switch (queue->qid) { |
| 2357 |
case QID_RX: |
| 2358 |
queue->limit = 32; |
| 2359 |
queue->data_size = DATA_FRAME_SIZE; |
| 2360 |
queue->desc_size = RXD_DESC_SIZE; |
| 2361 |
queue->priv_size = sizeof(struct queue_entry_priv_usb); |
| 2362 |
break; |
| 2363 |
|
| 2364 |
case QID_AC_VO: |
| 2365 |
case QID_AC_VI: |
| 2366 |
case QID_AC_BE: |
| 2367 |
case QID_AC_BK: |
| 2368 |
queue->limit = 32; |
| 2369 |
queue->data_size = DATA_FRAME_SIZE; |
| 2370 |
queue->desc_size = TXD_DESC_SIZE; |
| 2371 |
queue->priv_size = sizeof(struct queue_entry_priv_usb); |
| 2372 |
break; |
| 2373 |
|
| 2374 |
case QID_BEACON: |
| 2375 |
queue->limit = 4; |
| 2376 |
queue->data_size = MGMT_FRAME_SIZE; |
| 2377 |
queue->desc_size = TXINFO_SIZE; |
| 2378 |
queue->priv_size = sizeof(struct queue_entry_priv_usb); |
| 2379 |
break; |
| 2380 |
|
| 2381 |
case QID_ATIM: |
| 2382 |
default: |
| 2383 |
BUG(); |
| 2384 |
break; |
| 2385 |
} |
| 2386 |
} |
| 2387 |
|
| 2388 |
static const struct rt2x00_ops rt73usb_ops = { |
| 2389 |
.name = KBUILD_MODNAME, |
| 2390 |
.max_ap_intf = 4, |
| 2391 |
.eeprom_size = EEPROM_SIZE, |
| 2392 |
.rf_size = RF_SIZE, |
| 2393 |
.tx_queues = NUM_TX_QUEUES, |
| 2394 |
.queue_init = rt73usb_queue_init, |
| 2395 |
.lib = &rt73usb_rt2x00_ops, |
| 2396 |
.hw = &rt73usb_mac80211_ops, |
| 2397 |
#ifdef CONFIG_RT2X00_LIB_DEBUGFS |
| 2398 |
.debugfs = &rt73usb_rt2x00debug, |
| 2399 |
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ |
| 2400 |
}; |
| 2401 |
|
| 2402 |
/* |
| 2403 |
* rt73usb module information. |
| 2404 |
*/ |
| 2405 |
static const struct usb_device_id rt73usb_device_table[] = { |
| 2406 |
/* AboCom */ |
| 2407 |
{ USB_DEVICE(0x07b8, 0xb21b) }, |
| 2408 |
{ USB_DEVICE(0x07b8, 0xb21c) }, |
| 2409 |
{ USB_DEVICE(0x07b8, 0xb21d) }, |
| 2410 |
{ USB_DEVICE(0x07b8, 0xb21e) }, |
| 2411 |
{ USB_DEVICE(0x07b8, 0xb21f) }, |
| 2412 |
/* AL */ |
| 2413 |
{ USB_DEVICE(0x14b2, 0x3c10) }, |
| 2414 |
/* Amigo */ |
| 2415 |
{ USB_DEVICE(0x148f, 0x9021) }, |
| 2416 |
{ USB_DEVICE(0x0eb0, 0x9021) }, |
| 2417 |
/* AMIT */ |
| 2418 |
{ USB_DEVICE(0x18c5, 0x0002) }, |
| 2419 |
/* Askey */ |
| 2420 |
{ USB_DEVICE(0x1690, 0x0722) }, |
| 2421 |
/* ASUS */ |
| 2422 |
{ USB_DEVICE(0x0b05, 0x1723) }, |
| 2423 |
{ USB_DEVICE(0x0b05, 0x1724) }, |
| 2424 |
/* Belkin */ |
| 2425 |
{ USB_DEVICE(0x050d, 0x7050) }, /* FCC ID: K7SF5D7050B ver. 3.x */ |
| 2426 |
{ USB_DEVICE(0x050d, 0x705a) }, |
| 2427 |
{ USB_DEVICE(0x050d, 0x905b) }, |
| 2428 |
{ USB_DEVICE(0x050d, 0x905c) }, |
| 2429 |
/* Billionton */ |
| 2430 |
{ USB_DEVICE(0x1631, 0xc019) }, |
| 2431 |
{ USB_DEVICE(0x08dd, 0x0120) }, |
| 2432 |
/* Buffalo */ |
| 2433 |
{ USB_DEVICE(0x0411, 0x00d8) }, |
| 2434 |
{ USB_DEVICE(0x0411, 0x00d9) }, |
| 2435 |
{ USB_DEVICE(0x0411, 0x00e6) }, |
| 2436 |
{ USB_DEVICE(0x0411, 0x00f4) }, |
| 2437 |
{ USB_DEVICE(0x0411, 0x0116) }, |
| 2438 |
{ USB_DEVICE(0x0411, 0x0119) }, |
| 2439 |
{ USB_DEVICE(0x0411, 0x0137) }, |
| 2440 |
/* CEIVA */ |
| 2441 |
{ USB_DEVICE(0x178d, 0x02be) }, |
| 2442 |
/* CNet */ |
| 2443 |
{ USB_DEVICE(0x1371, 0x9022) }, |
| 2444 |
{ USB_DEVICE(0x1371, 0x9032) }, |
| 2445 |
/* Conceptronic */ |
| 2446 |
{ USB_DEVICE(0x14b2, 0x3c22) }, |
| 2447 |
/* Corega */ |
| 2448 |
{ USB_DEVICE(0x07aa, 0x002e) }, |
| 2449 |
/* D-Link */ |
| 2450 |
{ USB_DEVICE(0x07d1, 0x3c03) }, |
| 2451 |
{ USB_DEVICE(0x07d1, 0x3c04) }, |
| 2452 |
{ USB_DEVICE(0x07d1, 0x3c06) }, |
| 2453 |
{ USB_DEVICE(0x07d1, 0x3c07) }, |
| 2454 |
/* Edimax */ |
| 2455 |
{ USB_DEVICE(0x7392, 0x7318) }, |
| 2456 |
{ USB_DEVICE(0x7392, 0x7618) }, |
| 2457 |
/* EnGenius */ |
| 2458 |
{ USB_DEVICE(0x1740, 0x3701) }, |
| 2459 |
/* Gemtek */ |
| 2460 |
{ USB_DEVICE(0x15a9, 0x0004) }, |
| 2461 |
/* Gigabyte */ |
| 2462 |
{ USB_DEVICE(0x1044, 0x8008) }, |
| 2463 |
{ USB_DEVICE(0x1044, 0x800a) }, |
| 2464 |
/* Huawei-3Com */ |
| 2465 |
{ USB_DEVICE(0x1472, 0x0009) }, |
| 2466 |
/* Hercules */ |
| 2467 |
{ USB_DEVICE(0x06f8, 0xe002) }, |
| 2468 |
{ USB_DEVICE(0x06f8, 0xe010) }, |
| 2469 |
{ USB_DEVICE(0x06f8, 0xe020) }, |
| 2470 |
/* Linksys */ |
| 2471 |
{ USB_DEVICE(0x13b1, 0x0020) }, |
| 2472 |
{ USB_DEVICE(0x13b1, 0x0023) }, |
| 2473 |
{ USB_DEVICE(0x13b1, 0x0028) }, |
| 2474 |
/* MSI */ |
| 2475 |
{ USB_DEVICE(0x0db0, 0x4600) }, |
| 2476 |
{ USB_DEVICE(0x0db0, 0x6877) }, |
| 2477 |
{ USB_DEVICE(0x0db0, 0x6874) }, |
| 2478 |
{ USB_DEVICE(0x0db0, 0xa861) }, |
| 2479 |
{ USB_DEVICE(0x0db0, 0xa874) }, |
| 2480 |
/* Ovislink */ |
| 2481 |
{ USB_DEVICE(0x1b75, 0x7318) }, |
| 2482 |
/* Ralink */ |
| 2483 |
{ USB_DEVICE(0x04bb, 0x093d) }, |
| 2484 |
{ USB_DEVICE(0x148f, 0x2573) }, |
| 2485 |
{ USB_DEVICE(0x148f, 0x2671) }, |
| 2486 |
{ USB_DEVICE(0x0812, 0x3101) }, |
| 2487 |
/* Qcom */ |
| 2488 |
{ USB_DEVICE(0x18e8, 0x6196) }, |
| 2489 |
{ USB_DEVICE(0x18e8, 0x6229) }, |
| 2490 |
{ USB_DEVICE(0x18e8, 0x6238) }, |
| 2491 |
/* Samsung */ |
| 2492 |
{ USB_DEVICE(0x04e8, 0x4471) }, |
| 2493 |
/* Senao */ |
| 2494 |
{ USB_DEVICE(0x1740, 0x7100) }, |
| 2495 |
/* Sitecom */ |
| 2496 |
{ USB_DEVICE(0x0df6, 0x0024) }, |
| 2497 |
{ USB_DEVICE(0x0df6, 0x0027) }, |
| 2498 |
{ USB_DEVICE(0x0df6, 0x002f) }, |
| 2499 |
{ USB_DEVICE(0x0df6, 0x90ac) }, |
| 2500 |
{ USB_DEVICE(0x0df6, 0x9712) }, |
| 2501 |
/* Surecom */ |
| 2502 |
{ USB_DEVICE(0x0769, 0x31f3) }, |
| 2503 |
/* Tilgin */ |
| 2504 |
{ USB_DEVICE(0x6933, 0x5001) }, |
| 2505 |
/* Philips */ |
| 2506 |
{ USB_DEVICE(0x0471, 0x200a) }, |
| 2507 |
/* Planex */ |
| 2508 |
{ USB_DEVICE(0x2019, 0xab01) }, |
| 2509 |
{ USB_DEVICE(0x2019, 0xab50) }, |
| 2510 |
/* WideTell */ |
| 2511 |
{ USB_DEVICE(0x7167, 0x3840) }, |
| 2512 |
/* Zcom */ |
| 2513 |
{ USB_DEVICE(0x0cde, 0x001c) }, |
| 2514 |
/* ZyXEL */ |
| 2515 |
{ USB_DEVICE(0x0586, 0x3415) }, |
| 2516 |
{ 0, } |
| 2517 |
}; |
| 2518 |
|
| 2519 |
MODULE_AUTHOR(DRV_PROJECT); |
| 2520 |
MODULE_VERSION(DRV_VERSION); |
| 2521 |
MODULE_DESCRIPTION("Ralink RT73 USB Wireless LAN driver."); |
| 2522 |
MODULE_DEVICE_TABLE(usb, rt73usb_device_table); |
| 2523 |
MODULE_FIRMWARE(FIRMWARE_RT2571); |
| 2524 |
MODULE_LICENSE("GPL"); |
| 2525 |
|
| 2526 |
static int rt73usb_probe(struct usb_interface *usb_intf, |
| 2527 |
const struct usb_device_id *id) |
| 2528 |
{ |
| 2529 |
return rt2x00usb_probe(usb_intf, &rt73usb_ops); |
| 2530 |
} |
| 2531 |
|
| 2532 |
static struct usb_driver rt73usb_driver = { |
| 2533 |
.name = KBUILD_MODNAME, |
| 2534 |
.id_table = rt73usb_device_table, |
| 2535 |
.probe = rt73usb_probe, |
| 2536 |
.disconnect = rt2x00usb_disconnect, |
| 2537 |
.suspend = rt2x00usb_suspend, |
| 2538 |
.resume = rt2x00usb_resume, |
| 2539 |
.reset_resume = rt2x00usb_resume, |
| 2540 |
.disable_hub_initiated_lpm = 1, |
| 2541 |
}; |
| 2542 |
|
| 2543 |
module_usb_driver(rt73usb_driver); |