| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
Copyright (C) 2010 Willow Garage <http://www.willowgarage.com> |
| 4 |
Copyright (C) 2004 - 2010 Ivo van Doorn <[email protected]> |
| 5 |
<http://rt2x00.serialmonkey.com> |
| 6 |
|
| 7 |
*/ |
| 8 |
|
| 9 |
/* |
| 10 |
Module: rt2x00lib |
| 11 |
Abstract: rt2x00 generic device routines. |
| 12 |
*/ |
| 13 |
|
| 14 |
#include <linux/kernel.h> |
| 15 |
#include <linux/module.h> |
| 16 |
#include <linux/slab.h> |
| 17 |
#include <linux/log2.h> |
| 18 |
#include <linux/of.h> |
| 19 |
#include <linux/of_net.h> |
| 20 |
|
| 21 |
#include "rt2x00.h" |
| 22 |
#include "rt2x00lib.h" |
| 23 |
|
| 24 |
/* |
| 25 |
* Utility functions. |
| 26 |
*/ |
| 27 |
u32 rt2x00lib_get_bssidx(struct rt2x00_dev *rt2x00dev, |
| 28 |
struct ieee80211_vif *vif) |
| 29 |
{ |
| 30 |
/* |
| 31 |
* When in STA mode, bssidx is always 0 otherwise local_address[5] |
| 32 |
* contains the bss number, see BSS_ID_MASK comments for details. |
| 33 |
*/ |
| 34 |
if (rt2x00dev->intf_sta_count) |
| 35 |
return 0; |
| 36 |
return vif->addr[5] & (rt2x00dev->ops->max_ap_intf - 1); |
| 37 |
} |
| 38 |
EXPORT_SYMBOL_GPL(rt2x00lib_get_bssidx); |
| 39 |
|
| 40 |
/* |
| 41 |
* Radio control handlers. |
| 42 |
*/ |
| 43 |
int rt2x00lib_enable_radio(struct rt2x00_dev *rt2x00dev) |
| 44 |
{ |
| 45 |
int status; |
| 46 |
|
| 47 |
/* |
| 48 |
* Don't enable the radio twice. |
| 49 |
* And check if the hardware button has been disabled. |
| 50 |
*/ |
| 51 |
if (test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) |
| 52 |
return 0; |
| 53 |
|
| 54 |
/* |
| 55 |
* Initialize all data queues. |
| 56 |
*/ |
| 57 |
rt2x00queue_init_queues(rt2x00dev); |
| 58 |
|
| 59 |
/* |
| 60 |
* Enable radio. |
| 61 |
*/ |
| 62 |
status = |
| 63 |
rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_ON); |
| 64 |
if (status) |
| 65 |
return status; |
| 66 |
|
| 67 |
rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_IRQ_ON); |
| 68 |
|
| 69 |
rt2x00leds_led_radio(rt2x00dev, true); |
| 70 |
rt2x00led_led_activity(rt2x00dev, true); |
| 71 |
|
| 72 |
set_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags); |
| 73 |
|
| 74 |
/* |
| 75 |
* Enable queues. |
| 76 |
*/ |
| 77 |
rt2x00queue_start_queues(rt2x00dev); |
| 78 |
rt2x00link_start_tuner(rt2x00dev); |
| 79 |
|
| 80 |
/* |
| 81 |
* Start watchdog monitoring. |
| 82 |
*/ |
| 83 |
rt2x00link_start_watchdog(rt2x00dev); |
| 84 |
|
| 85 |
return 0; |
| 86 |
} |
| 87 |
|
| 88 |
void rt2x00lib_disable_radio(struct rt2x00_dev *rt2x00dev) |
| 89 |
{ |
| 90 |
if (!test_and_clear_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) |
| 91 |
return; |
| 92 |
|
| 93 |
/* |
| 94 |
* Stop watchdog monitoring. |
| 95 |
*/ |
| 96 |
rt2x00link_stop_watchdog(rt2x00dev); |
| 97 |
|
| 98 |
/* |
| 99 |
* Stop all queues |
| 100 |
*/ |
| 101 |
rt2x00link_stop_tuner(rt2x00dev); |
| 102 |
rt2x00queue_stop_queues(rt2x00dev); |
| 103 |
rt2x00queue_flush_queues(rt2x00dev, true); |
| 104 |
rt2x00queue_stop_queue(rt2x00dev->bcn); |
| 105 |
|
| 106 |
/* |
| 107 |
* Disable radio. |
| 108 |
*/ |
| 109 |
rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_OFF); |
| 110 |
rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_IRQ_OFF); |
| 111 |
rt2x00led_led_activity(rt2x00dev, false); |
| 112 |
rt2x00leds_led_radio(rt2x00dev, false); |
| 113 |
} |
| 114 |
|
| 115 |
static void rt2x00lib_intf_scheduled_iter(void *data, u8 *mac, |
| 116 |
struct ieee80211_vif *vif) |
| 117 |
{ |
| 118 |
struct rt2x00_dev *rt2x00dev = data; |
| 119 |
struct rt2x00_intf *intf = vif_to_intf(vif); |
| 120 |
|
| 121 |
/* |
| 122 |
* It is possible the radio was disabled while the work had been |
| 123 |
* scheduled. If that happens we should return here immediately, |
| 124 |
* note that in the spinlock protected area above the delayed_flags |
| 125 |
* have been cleared correctly. |
| 126 |
*/ |
| 127 |
if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) |
| 128 |
return; |
| 129 |
|
| 130 |
if (test_and_clear_bit(DELAYED_UPDATE_BEACON, &intf->delayed_flags)) { |
| 131 |
mutex_lock(&intf->beacon_skb_mutex); |
| 132 |
rt2x00queue_update_beacon(rt2x00dev, vif); |
| 133 |
mutex_unlock(&intf->beacon_skb_mutex); |
| 134 |
} |
| 135 |
} |
| 136 |
|
| 137 |
static void rt2x00lib_intf_scheduled(struct work_struct *work) |
| 138 |
{ |
| 139 |
struct rt2x00_dev *rt2x00dev = |
| 140 |
container_of(work, struct rt2x00_dev, intf_work); |
| 141 |
|
| 142 |
/* |
| 143 |
* Iterate over each interface and perform the |
| 144 |
* requested configurations. |
| 145 |
*/ |
| 146 |
ieee80211_iterate_active_interfaces(rt2x00dev->hw, |
| 147 |
IEEE80211_IFACE_ITER_RESUME_ALL, |
| 148 |
rt2x00lib_intf_scheduled_iter, |
| 149 |
rt2x00dev); |
| 150 |
} |
| 151 |
|
| 152 |
static void rt2x00lib_autowakeup(struct work_struct *work) |
| 153 |
{ |
| 154 |
struct rt2x00_dev *rt2x00dev = |
| 155 |
container_of(work, struct rt2x00_dev, autowakeup_work.work); |
| 156 |
|
| 157 |
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) |
| 158 |
return; |
| 159 |
|
| 160 |
if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_AWAKE)) |
| 161 |
rt2x00_err(rt2x00dev, "Device failed to wakeup\n"); |
| 162 |
clear_bit(CONFIG_POWERSAVING, &rt2x00dev->flags); |
| 163 |
} |
| 164 |
|
| 165 |
/* |
| 166 |
* Interrupt context handlers. |
| 167 |
*/ |
| 168 |
static void rt2x00lib_bc_buffer_iter(void *data, u8 *mac, |
| 169 |
struct ieee80211_vif *vif) |
| 170 |
{ |
| 171 |
struct ieee80211_tx_control control = {}; |
| 172 |
struct rt2x00_dev *rt2x00dev = data; |
| 173 |
struct sk_buff *skb; |
| 174 |
|
| 175 |
/* |
| 176 |
* Only AP mode interfaces do broad- and multicast buffering |
| 177 |
*/ |
| 178 |
if (vif->type != NL80211_IFTYPE_AP) |
| 179 |
return; |
| 180 |
|
| 181 |
/* |
| 182 |
* Send out buffered broad- and multicast frames |
| 183 |
*/ |
| 184 |
skb = ieee80211_get_buffered_bc(rt2x00dev->hw, vif); |
| 185 |
while (skb) { |
| 186 |
rt2x00mac_tx(rt2x00dev->hw, &control, skb); |
| 187 |
skb = ieee80211_get_buffered_bc(rt2x00dev->hw, vif); |
| 188 |
} |
| 189 |
} |
| 190 |
|
| 191 |
static void rt2x00lib_beaconupdate_iter(void *data, u8 *mac, |
| 192 |
struct ieee80211_vif *vif) |
| 193 |
{ |
| 194 |
struct rt2x00_dev *rt2x00dev = data; |
| 195 |
|
| 196 |
if (vif->type != NL80211_IFTYPE_AP && |
| 197 |
vif->type != NL80211_IFTYPE_ADHOC && |
| 198 |
vif->type != NL80211_IFTYPE_MESH_POINT) |
| 199 |
return; |
| 200 |
|
| 201 |
/* |
| 202 |
* Update the beacon without locking. This is safe on PCI devices |
| 203 |
* as they only update the beacon periodically here. This should |
| 204 |
* never be called for USB devices. |
| 205 |
*/ |
| 206 |
WARN_ON(rt2x00_is_usb(rt2x00dev)); |
| 207 |
rt2x00queue_update_beacon(rt2x00dev, vif); |
| 208 |
} |
| 209 |
|
| 210 |
void rt2x00lib_beacondone(struct rt2x00_dev *rt2x00dev) |
| 211 |
{ |
| 212 |
if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) |
| 213 |
return; |
| 214 |
|
| 215 |
/* send buffered bc/mc frames out for every bssid */ |
| 216 |
ieee80211_iterate_active_interfaces_atomic( |
| 217 |
rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL, |
| 218 |
rt2x00lib_bc_buffer_iter, rt2x00dev); |
| 219 |
/* |
| 220 |
* Devices with pre tbtt interrupt don't need to update the beacon |
| 221 |
* here as they will fetch the next beacon directly prior to |
| 222 |
* transmission. |
| 223 |
*/ |
| 224 |
if (rt2x00_has_cap_pre_tbtt_interrupt(rt2x00dev)) |
| 225 |
return; |
| 226 |
|
| 227 |
/* fetch next beacon */ |
| 228 |
ieee80211_iterate_active_interfaces_atomic( |
| 229 |
rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL, |
| 230 |
rt2x00lib_beaconupdate_iter, rt2x00dev); |
| 231 |
} |
| 232 |
EXPORT_SYMBOL_GPL(rt2x00lib_beacondone); |
| 233 |
|
| 234 |
void rt2x00lib_pretbtt(struct rt2x00_dev *rt2x00dev) |
| 235 |
{ |
| 236 |
if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) |
| 237 |
return; |
| 238 |
|
| 239 |
/* fetch next beacon */ |
| 240 |
ieee80211_iterate_active_interfaces_atomic( |
| 241 |
rt2x00dev->hw, IEEE80211_IFACE_ITER_RESUME_ALL, |
| 242 |
rt2x00lib_beaconupdate_iter, rt2x00dev); |
| 243 |
} |
| 244 |
EXPORT_SYMBOL_GPL(rt2x00lib_pretbtt); |
| 245 |
|
| 246 |
void rt2x00lib_dmastart(struct queue_entry *entry) |
| 247 |
{ |
| 248 |
set_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags); |
| 249 |
rt2x00queue_index_inc(entry, Q_INDEX); |
| 250 |
} |
| 251 |
EXPORT_SYMBOL_GPL(rt2x00lib_dmastart); |
| 252 |
|
| 253 |
void rt2x00lib_dmadone(struct queue_entry *entry) |
| 254 |
{ |
| 255 |
set_bit(ENTRY_DATA_STATUS_PENDING, &entry->flags); |
| 256 |
clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags); |
| 257 |
rt2x00queue_index_inc(entry, Q_INDEX_DMA_DONE); |
| 258 |
} |
| 259 |
EXPORT_SYMBOL_GPL(rt2x00lib_dmadone); |
| 260 |
|
| 261 |
static inline int rt2x00lib_txdone_bar_status(struct queue_entry *entry) |
| 262 |
{ |
| 263 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 264 |
struct ieee80211_bar *bar = (void *) entry->skb->data; |
| 265 |
struct rt2x00_bar_list_entry *bar_entry; |
| 266 |
int ret; |
| 267 |
|
| 268 |
if (likely(!ieee80211_is_back_req(bar->frame_control))) |
| 269 |
return 0; |
| 270 |
|
| 271 |
/* |
| 272 |
* Unlike all other frames, the status report for BARs does |
| 273 |
* not directly come from the hardware as it is incapable of |
| 274 |
* matching a BA to a previously send BAR. The hardware will |
| 275 |
* report all BARs as if they weren't acked at all. |
| 276 |
* |
| 277 |
* Instead the RX-path will scan for incoming BAs and set the |
| 278 |
* block_acked flag if it sees one that was likely caused by |
| 279 |
* a BAR from us. |
| 280 |
* |
| 281 |
* Remove remaining BARs here and return their status for |
| 282 |
* TX done processing. |
| 283 |
*/ |
| 284 |
ret = 0; |
| 285 |
rcu_read_lock(); |
| 286 |
list_for_each_entry_rcu(bar_entry, &rt2x00dev->bar_list, list) { |
| 287 |
if (bar_entry->entry != entry) |
| 288 |
continue; |
| 289 |
|
| 290 |
spin_lock_bh(&rt2x00dev->bar_list_lock); |
| 291 |
/* Return whether this BAR was blockacked or not */ |
| 292 |
ret = bar_entry->block_acked; |
| 293 |
/* Remove the BAR from our checklist */ |
| 294 |
list_del_rcu(&bar_entry->list); |
| 295 |
spin_unlock_bh(&rt2x00dev->bar_list_lock); |
| 296 |
kfree_rcu(bar_entry, head); |
| 297 |
|
| 298 |
break; |
| 299 |
} |
| 300 |
rcu_read_unlock(); |
| 301 |
|
| 302 |
return ret; |
| 303 |
} |
| 304 |
|
| 305 |
static void rt2x00lib_fill_tx_status(struct rt2x00_dev *rt2x00dev, |
| 306 |
struct ieee80211_tx_info *tx_info, |
| 307 |
struct skb_frame_desc *skbdesc, |
| 308 |
struct txdone_entry_desc *txdesc, |
| 309 |
bool success) |
| 310 |
{ |
| 311 |
u8 rate_idx, rate_flags, retry_rates; |
| 312 |
int i; |
| 313 |
|
| 314 |
rate_idx = skbdesc->tx_rate_idx; |
| 315 |
rate_flags = skbdesc->tx_rate_flags; |
| 316 |
retry_rates = test_bit(TXDONE_FALLBACK, &txdesc->flags) ? |
| 317 |
(txdesc->retry + 1) : 1; |
| 318 |
|
| 319 |
/* |
| 320 |
* Initialize TX status |
| 321 |
*/ |
| 322 |
memset(&tx_info->status, 0, sizeof(tx_info->status)); |
| 323 |
tx_info->status.ack_signal = 0; |
| 324 |
|
| 325 |
/* |
| 326 |
* Frame was send with retries, hardware tried |
| 327 |
* different rates to send out the frame, at each |
| 328 |
* retry it lowered the rate 1 step except when the |
| 329 |
* lowest rate was used. |
| 330 |
*/ |
| 331 |
for (i = 0; i < retry_rates && i < IEEE80211_TX_MAX_RATES; i++) { |
| 332 |
tx_info->status.rates[i].idx = rate_idx - i; |
| 333 |
tx_info->status.rates[i].flags = rate_flags; |
| 334 |
|
| 335 |
if (rate_idx - i == 0) { |
| 336 |
/* |
| 337 |
* The lowest rate (index 0) was used until the |
| 338 |
* number of max retries was reached. |
| 339 |
*/ |
| 340 |
tx_info->status.rates[i].count = retry_rates - i; |
| 341 |
i++; |
| 342 |
break; |
| 343 |
} |
| 344 |
tx_info->status.rates[i].count = 1; |
| 345 |
} |
| 346 |
if (i < (IEEE80211_TX_MAX_RATES - 1)) |
| 347 |
tx_info->status.rates[i].idx = -1; /* terminate */ |
| 348 |
|
| 349 |
if (test_bit(TXDONE_NO_ACK_REQ, &txdesc->flags)) |
| 350 |
tx_info->flags |= IEEE80211_TX_CTL_NO_ACK; |
| 351 |
|
| 352 |
if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK)) { |
| 353 |
if (success) |
| 354 |
tx_info->flags |= IEEE80211_TX_STAT_ACK; |
| 355 |
else |
| 356 |
rt2x00dev->low_level_stats.dot11ACKFailureCount++; |
| 357 |
} |
| 358 |
|
| 359 |
/* |
| 360 |
* Every single frame has its own tx status, hence report |
| 361 |
* every frame as ampdu of size 1. |
| 362 |
* |
| 363 |
* TODO: if we can find out how many frames were aggregated |
| 364 |
* by the hw we could provide the real ampdu_len to mac80211 |
| 365 |
* which would allow the rc algorithm to better decide on |
| 366 |
* which rates are suitable. |
| 367 |
*/ |
| 368 |
if (test_bit(TXDONE_AMPDU, &txdesc->flags) || |
| 369 |
tx_info->flags & IEEE80211_TX_CTL_AMPDU) { |
| 370 |
tx_info->flags |= IEEE80211_TX_STAT_AMPDU | |
| 371 |
IEEE80211_TX_CTL_AMPDU; |
| 372 |
tx_info->status.ampdu_len = 1; |
| 373 |
tx_info->status.ampdu_ack_len = success ? 1 : 0; |
| 374 |
} |
| 375 |
|
| 376 |
if (rate_flags & IEEE80211_TX_RC_USE_RTS_CTS) { |
| 377 |
if (success) |
| 378 |
rt2x00dev->low_level_stats.dot11RTSSuccessCount++; |
| 379 |
else |
| 380 |
rt2x00dev->low_level_stats.dot11RTSFailureCount++; |
| 381 |
} |
| 382 |
} |
| 383 |
|
| 384 |
static void rt2x00lib_clear_entry(struct rt2x00_dev *rt2x00dev, |
| 385 |
struct queue_entry *entry) |
| 386 |
{ |
| 387 |
/* |
| 388 |
* Make this entry available for reuse. |
| 389 |
*/ |
| 390 |
entry->skb = NULL; |
| 391 |
entry->flags = 0; |
| 392 |
|
| 393 |
rt2x00dev->ops->lib->clear_entry(entry); |
| 394 |
|
| 395 |
rt2x00queue_index_inc(entry, Q_INDEX_DONE); |
| 396 |
|
| 397 |
/* |
| 398 |
* If the data queue was below the threshold before the txdone |
| 399 |
* handler we must make sure the packet queue in the mac80211 stack |
| 400 |
* is reenabled when the txdone handler has finished. This has to be |
| 401 |
* serialized with rt2x00mac_tx(), otherwise we can wake up queue |
| 402 |
* before it was stopped. |
| 403 |
*/ |
| 404 |
spin_lock_bh(&entry->queue->tx_lock); |
| 405 |
if (!rt2x00queue_threshold(entry->queue)) |
| 406 |
rt2x00queue_unpause_queue(entry->queue); |
| 407 |
spin_unlock_bh(&entry->queue->tx_lock); |
| 408 |
} |
| 409 |
|
| 410 |
void rt2x00lib_txdone_nomatch(struct queue_entry *entry, |
| 411 |
struct txdone_entry_desc *txdesc) |
| 412 |
{ |
| 413 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 414 |
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); |
| 415 |
struct ieee80211_tx_info txinfo = {}; |
| 416 |
bool success; |
| 417 |
|
| 418 |
/* |
| 419 |
* Unmap the skb. |
| 420 |
*/ |
| 421 |
rt2x00queue_unmap_skb(entry); |
| 422 |
|
| 423 |
/* |
| 424 |
* Signal that the TX descriptor is no longer in the skb. |
| 425 |
*/ |
| 426 |
skbdesc->flags &= ~SKBDESC_DESC_IN_SKB; |
| 427 |
|
| 428 |
/* |
| 429 |
* Send frame to debugfs immediately, after this call is completed |
| 430 |
* we are going to overwrite the skb->cb array. |
| 431 |
*/ |
| 432 |
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry); |
| 433 |
|
| 434 |
/* |
| 435 |
* Determine if the frame has been successfully transmitted and |
| 436 |
* remove BARs from our check list while checking for their |
| 437 |
* TX status. |
| 438 |
*/ |
| 439 |
success = |
| 440 |
rt2x00lib_txdone_bar_status(entry) || |
| 441 |
test_bit(TXDONE_SUCCESS, &txdesc->flags); |
| 442 |
|
| 443 |
if (!test_bit(TXDONE_UNKNOWN, &txdesc->flags)) { |
| 444 |
/* |
| 445 |
* Update TX statistics. |
| 446 |
*/ |
| 447 |
rt2x00dev->link.qual.tx_success += success; |
| 448 |
rt2x00dev->link.qual.tx_failed += !success; |
| 449 |
|
| 450 |
rt2x00lib_fill_tx_status(rt2x00dev, &txinfo, skbdesc, txdesc, |
| 451 |
success); |
| 452 |
ieee80211_tx_status_noskb(rt2x00dev->hw, skbdesc->sta, &txinfo); |
| 453 |
} |
| 454 |
|
| 455 |
dev_kfree_skb_any(entry->skb); |
| 456 |
rt2x00lib_clear_entry(rt2x00dev, entry); |
| 457 |
} |
| 458 |
EXPORT_SYMBOL_GPL(rt2x00lib_txdone_nomatch); |
| 459 |
|
| 460 |
void rt2x00lib_txdone(struct queue_entry *entry, |
| 461 |
struct txdone_entry_desc *txdesc) |
| 462 |
{ |
| 463 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 464 |
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb); |
| 465 |
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); |
| 466 |
u8 skbdesc_flags = skbdesc->flags; |
| 467 |
unsigned int header_length; |
| 468 |
bool success; |
| 469 |
|
| 470 |
/* |
| 471 |
* Unmap the skb. |
| 472 |
*/ |
| 473 |
rt2x00queue_unmap_skb(entry); |
| 474 |
|
| 475 |
/* |
| 476 |
* Remove the extra tx headroom from the skb. |
| 477 |
*/ |
| 478 |
skb_pull(entry->skb, rt2x00dev->extra_tx_headroom); |
| 479 |
|
| 480 |
/* |
| 481 |
* Signal that the TX descriptor is no longer in the skb. |
| 482 |
*/ |
| 483 |
skbdesc->flags &= ~SKBDESC_DESC_IN_SKB; |
| 484 |
|
| 485 |
/* |
| 486 |
* Determine the length of 802.11 header. |
| 487 |
*/ |
| 488 |
header_length = ieee80211_get_hdrlen_from_skb(entry->skb); |
| 489 |
|
| 490 |
/* |
| 491 |
* Remove L2 padding which was added during |
| 492 |
*/ |
| 493 |
if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_L2PAD)) |
| 494 |
rt2x00queue_remove_l2pad(entry->skb, header_length); |
| 495 |
|
| 496 |
/* |
| 497 |
* If the IV/EIV data was stripped from the frame before it was |
| 498 |
* passed to the hardware, we should now reinsert it again because |
| 499 |
* mac80211 will expect the same data to be present in the |
| 500 |
* frame as it was passed to us. |
| 501 |
*/ |
| 502 |
if (rt2x00_has_cap_hw_crypto(rt2x00dev)) |
| 503 |
rt2x00crypto_tx_insert_iv(entry->skb, header_length); |
| 504 |
|
| 505 |
/* |
| 506 |
* Send frame to debugfs immediately, after this call is completed |
| 507 |
* we are going to overwrite the skb->cb array. |
| 508 |
*/ |
| 509 |
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry); |
| 510 |
|
| 511 |
/* |
| 512 |
* Determine if the frame has been successfully transmitted and |
| 513 |
* remove BARs from our check list while checking for their |
| 514 |
* TX status. |
| 515 |
*/ |
| 516 |
success = |
| 517 |
rt2x00lib_txdone_bar_status(entry) || |
| 518 |
test_bit(TXDONE_SUCCESS, &txdesc->flags) || |
| 519 |
test_bit(TXDONE_UNKNOWN, &txdesc->flags); |
| 520 |
|
| 521 |
/* |
| 522 |
* Update TX statistics. |
| 523 |
*/ |
| 524 |
rt2x00dev->link.qual.tx_success += success; |
| 525 |
rt2x00dev->link.qual.tx_failed += !success; |
| 526 |
|
| 527 |
rt2x00lib_fill_tx_status(rt2x00dev, tx_info, skbdesc, txdesc, success); |
| 528 |
|
| 529 |
/* |
| 530 |
* Only send the status report to mac80211 when it's a frame |
| 531 |
* that originated in mac80211. If this was a extra frame coming |
| 532 |
* through a mac80211 library call (RTS/CTS) then we should not |
| 533 |
* send the status report back. |
| 534 |
*/ |
| 535 |
if (!(skbdesc_flags & SKBDESC_NOT_MAC80211)) { |
| 536 |
if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_TASKLET_CONTEXT)) |
| 537 |
ieee80211_tx_status_skb(rt2x00dev->hw, entry->skb); |
| 538 |
else |
| 539 |
ieee80211_tx_status_ni(rt2x00dev->hw, entry->skb); |
| 540 |
} else { |
| 541 |
dev_kfree_skb_any(entry->skb); |
| 542 |
} |
| 543 |
|
| 544 |
rt2x00lib_clear_entry(rt2x00dev, entry); |
| 545 |
} |
| 546 |
EXPORT_SYMBOL_GPL(rt2x00lib_txdone); |
| 547 |
|
| 548 |
void rt2x00lib_txdone_noinfo(struct queue_entry *entry, u32 status) |
| 549 |
{ |
| 550 |
struct txdone_entry_desc txdesc; |
| 551 |
|
| 552 |
txdesc.flags = 0; |
| 553 |
__set_bit(status, &txdesc.flags); |
| 554 |
txdesc.retry = 0; |
| 555 |
|
| 556 |
rt2x00lib_txdone(entry, &txdesc); |
| 557 |
} |
| 558 |
EXPORT_SYMBOL_GPL(rt2x00lib_txdone_noinfo); |
| 559 |
|
| 560 |
static u8 *rt2x00lib_find_ie(u8 *data, unsigned int len, u8 ie) |
| 561 |
{ |
| 562 |
struct ieee80211_mgmt *mgmt = (void *)data; |
| 563 |
u8 *pos, *end; |
| 564 |
|
| 565 |
pos = (u8 *)mgmt->u.beacon.variable; |
| 566 |
end = data + len; |
| 567 |
while (pos < end) { |
| 568 |
if (pos + 2 + pos[1] > end) |
| 569 |
return NULL; |
| 570 |
|
| 571 |
if (pos[0] == ie) |
| 572 |
return pos; |
| 573 |
|
| 574 |
pos += 2 + pos[1]; |
| 575 |
} |
| 576 |
|
| 577 |
return NULL; |
| 578 |
} |
| 579 |
|
| 580 |
static void rt2x00lib_sleep(struct work_struct *work) |
| 581 |
{ |
| 582 |
struct rt2x00_dev *rt2x00dev = |
| 583 |
container_of(work, struct rt2x00_dev, sleep_work); |
| 584 |
|
| 585 |
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) |
| 586 |
return; |
| 587 |
|
| 588 |
/* |
| 589 |
* Check again is powersaving is enabled, to prevent races from delayed |
| 590 |
* work execution. |
| 591 |
*/ |
| 592 |
if (!test_bit(CONFIG_POWERSAVING, &rt2x00dev->flags)) |
| 593 |
rt2x00lib_config(rt2x00dev, &rt2x00dev->hw->conf, |
| 594 |
IEEE80211_CONF_CHANGE_PS); |
| 595 |
} |
| 596 |
|
| 597 |
static void rt2x00lib_rxdone_check_ba(struct rt2x00_dev *rt2x00dev, |
| 598 |
struct sk_buff *skb, |
| 599 |
struct rxdone_entry_desc *rxdesc) |
| 600 |
{ |
| 601 |
struct rt2x00_bar_list_entry *entry; |
| 602 |
struct ieee80211_bar *ba = (void *)skb->data; |
| 603 |
|
| 604 |
if (likely(!ieee80211_is_back(ba->frame_control))) |
| 605 |
return; |
| 606 |
|
| 607 |
if (rxdesc->size < sizeof(*ba) + FCS_LEN) |
| 608 |
return; |
| 609 |
|
| 610 |
rcu_read_lock(); |
| 611 |
list_for_each_entry_rcu(entry, &rt2x00dev->bar_list, list) { |
| 612 |
|
| 613 |
if (ba->start_seq_num != entry->start_seq_num) |
| 614 |
continue; |
| 615 |
|
| 616 |
#define TID_CHECK(a, b) ( \ |
| 617 |
((a) & cpu_to_le16(IEEE80211_BAR_CTRL_TID_INFO_MASK)) == \ |
| 618 |
((b) & cpu_to_le16(IEEE80211_BAR_CTRL_TID_INFO_MASK))) \ |
| 619 |
|
| 620 |
if (!TID_CHECK(ba->control, entry->control)) |
| 621 |
continue; |
| 622 |
|
| 623 |
#undef TID_CHECK |
| 624 |
|
| 625 |
if (!ether_addr_equal_64bits(ba->ra, entry->ta)) |
| 626 |
continue; |
| 627 |
|
| 628 |
if (!ether_addr_equal_64bits(ba->ta, entry->ra)) |
| 629 |
continue; |
| 630 |
|
| 631 |
/* Mark BAR since we received the according BA */ |
| 632 |
spin_lock_bh(&rt2x00dev->bar_list_lock); |
| 633 |
entry->block_acked = 1; |
| 634 |
spin_unlock_bh(&rt2x00dev->bar_list_lock); |
| 635 |
break; |
| 636 |
} |
| 637 |
rcu_read_unlock(); |
| 638 |
|
| 639 |
} |
| 640 |
|
| 641 |
static void rt2x00lib_rxdone_check_ps(struct rt2x00_dev *rt2x00dev, |
| 642 |
struct sk_buff *skb, |
| 643 |
struct rxdone_entry_desc *rxdesc) |
| 644 |
{ |
| 645 |
struct ieee80211_hdr *hdr = (void *) skb->data; |
| 646 |
struct ieee80211_tim_ie *tim_ie; |
| 647 |
u8 *tim; |
| 648 |
u8 tim_len; |
| 649 |
bool cam; |
| 650 |
|
| 651 |
/* If this is not a beacon, or if mac80211 has no powersaving |
| 652 |
* configured, or if the device is already in powersaving mode |
| 653 |
* we can exit now. */ |
| 654 |
if (likely(!ieee80211_is_beacon(hdr->frame_control) || |
| 655 |
!(rt2x00dev->hw->conf.flags & IEEE80211_CONF_PS))) |
| 656 |
return; |
| 657 |
|
| 658 |
/* min. beacon length + FCS_LEN */ |
| 659 |
if (skb->len <= 40 + FCS_LEN) |
| 660 |
return; |
| 661 |
|
| 662 |
/* and only beacons from the associated BSSID, please */ |
| 663 |
if (!(rxdesc->dev_flags & RXDONE_MY_BSS) || |
| 664 |
!rt2x00dev->aid) |
| 665 |
return; |
| 666 |
|
| 667 |
rt2x00dev->last_beacon = jiffies; |
| 668 |
|
| 669 |
tim = rt2x00lib_find_ie(skb->data, skb->len - FCS_LEN, WLAN_EID_TIM); |
| 670 |
if (!tim) |
| 671 |
return; |
| 672 |
|
| 673 |
if (tim[1] < sizeof(*tim_ie)) |
| 674 |
return; |
| 675 |
|
| 676 |
tim_len = tim[1]; |
| 677 |
tim_ie = (struct ieee80211_tim_ie *) &tim[2]; |
| 678 |
|
| 679 |
/* Check whenever the PHY can be turned off again. */ |
| 680 |
|
| 681 |
/* 1. What about buffered unicast traffic for our AID? */ |
| 682 |
cam = ieee80211_check_tim(tim_ie, tim_len, rt2x00dev->aid, false); |
| 683 |
|
| 684 |
/* 2. Maybe the AP wants to send multicast/broadcast data? */ |
| 685 |
cam |= (tim_ie->bitmap_ctrl & 0x01); |
| 686 |
|
| 687 |
if (!cam && !test_bit(CONFIG_POWERSAVING, &rt2x00dev->flags)) |
| 688 |
queue_work(rt2x00dev->workqueue, &rt2x00dev->sleep_work); |
| 689 |
} |
| 690 |
|
| 691 |
static int rt2x00lib_rxdone_read_signal(struct rt2x00_dev *rt2x00dev, |
| 692 |
struct rxdone_entry_desc *rxdesc) |
| 693 |
{ |
| 694 |
struct ieee80211_supported_band *sband; |
| 695 |
const struct rt2x00_rate *rate; |
| 696 |
unsigned int i; |
| 697 |
int signal = rxdesc->signal; |
| 698 |
int type = (rxdesc->dev_flags & RXDONE_SIGNAL_MASK); |
| 699 |
|
| 700 |
switch (rxdesc->rate_mode) { |
| 701 |
case RATE_MODE_CCK: |
| 702 |
case RATE_MODE_OFDM: |
| 703 |
/* |
| 704 |
* For non-HT rates the MCS value needs to contain the |
| 705 |
* actually used rate modulation (CCK or OFDM). |
| 706 |
*/ |
| 707 |
if (rxdesc->dev_flags & RXDONE_SIGNAL_MCS) |
| 708 |
signal = RATE_MCS(rxdesc->rate_mode, signal); |
| 709 |
|
| 710 |
sband = &rt2x00dev->bands[rt2x00dev->curr_band]; |
| 711 |
for (i = 0; i < sband->n_bitrates; i++) { |
| 712 |
rate = rt2x00_get_rate(sband->bitrates[i].hw_value); |
| 713 |
if (((type == RXDONE_SIGNAL_PLCP) && |
| 714 |
(rate->plcp == signal)) || |
| 715 |
((type == RXDONE_SIGNAL_BITRATE) && |
| 716 |
(rate->bitrate == signal)) || |
| 717 |
((type == RXDONE_SIGNAL_MCS) && |
| 718 |
(rate->mcs == signal))) { |
| 719 |
return i; |
| 720 |
} |
| 721 |
} |
| 722 |
break; |
| 723 |
case RATE_MODE_HT_MIX: |
| 724 |
case RATE_MODE_HT_GREENFIELD: |
| 725 |
if (signal >= 0 && signal <= 76) |
| 726 |
return signal; |
| 727 |
break; |
| 728 |
default: |
| 729 |
break; |
| 730 |
} |
| 731 |
|
| 732 |
rt2x00_warn(rt2x00dev, "Frame received with unrecognized signal, mode=0x%.4x, signal=0x%.4x, type=%d\n", |
| 733 |
rxdesc->rate_mode, signal, type); |
| 734 |
return 0; |
| 735 |
} |
| 736 |
|
| 737 |
void rt2x00lib_rxdone(struct queue_entry *entry, gfp_t gfp) |
| 738 |
{ |
| 739 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 740 |
struct rxdone_entry_desc rxdesc; |
| 741 |
struct sk_buff *skb; |
| 742 |
struct ieee80211_rx_status *rx_status; |
| 743 |
unsigned int header_length; |
| 744 |
int rate_idx; |
| 745 |
|
| 746 |
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) || |
| 747 |
!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) |
| 748 |
goto submit_entry; |
| 749 |
|
| 750 |
if (test_bit(ENTRY_DATA_IO_FAILED, &entry->flags)) |
| 751 |
goto submit_entry; |
| 752 |
|
| 753 |
/* |
| 754 |
* Allocate a new sk_buffer. If no new buffer available, drop the |
| 755 |
* received frame and reuse the existing buffer. |
| 756 |
*/ |
| 757 |
skb = rt2x00queue_alloc_rxskb(entry, gfp); |
| 758 |
if (!skb) |
| 759 |
goto submit_entry; |
| 760 |
|
| 761 |
/* |
| 762 |
* Unmap the skb. |
| 763 |
*/ |
| 764 |
rt2x00queue_unmap_skb(entry); |
| 765 |
|
| 766 |
/* |
| 767 |
* Extract the RXD details. |
| 768 |
*/ |
| 769 |
memset(&rxdesc, 0, sizeof(rxdesc)); |
| 770 |
rt2x00dev->ops->lib->fill_rxdone(entry, &rxdesc); |
| 771 |
|
| 772 |
/* |
| 773 |
* Check for valid size in case we get corrupted descriptor from |
| 774 |
* hardware. |
| 775 |
*/ |
| 776 |
if (unlikely(rxdesc.size == 0 || |
| 777 |
rxdesc.size > entry->queue->data_size)) { |
| 778 |
rt2x00_err(rt2x00dev, "Wrong frame size %d max %d\n", |
| 779 |
rxdesc.size, entry->queue->data_size); |
| 780 |
dev_kfree_skb(entry->skb); |
| 781 |
goto renew_skb; |
| 782 |
} |
| 783 |
|
| 784 |
/* |
| 785 |
* The data behind the ieee80211 header must be |
| 786 |
* aligned on a 4 byte boundary. |
| 787 |
*/ |
| 788 |
header_length = ieee80211_get_hdrlen_from_skb(entry->skb); |
| 789 |
|
| 790 |
/* |
| 791 |
* Hardware might have stripped the IV/EIV/ICV data, |
| 792 |
* in that case it is possible that the data was |
| 793 |
* provided separately (through hardware descriptor) |
| 794 |
* in which case we should reinsert the data into the frame. |
| 795 |
*/ |
| 796 |
if ((rxdesc.dev_flags & RXDONE_CRYPTO_IV) && |
| 797 |
(rxdesc.flags & RX_FLAG_IV_STRIPPED)) |
| 798 |
rt2x00crypto_rx_insert_iv(entry->skb, header_length, |
| 799 |
&rxdesc); |
| 800 |
else if (header_length && |
| 801 |
(rxdesc.size > header_length) && |
| 802 |
(rxdesc.dev_flags & RXDONE_L2PAD)) |
| 803 |
rt2x00queue_remove_l2pad(entry->skb, header_length); |
| 804 |
|
| 805 |
/* Trim buffer to correct size */ |
| 806 |
skb_trim(entry->skb, rxdesc.size); |
| 807 |
|
| 808 |
/* |
| 809 |
* Translate the signal to the correct bitrate index. |
| 810 |
*/ |
| 811 |
rate_idx = rt2x00lib_rxdone_read_signal(rt2x00dev, &rxdesc); |
| 812 |
if (rxdesc.rate_mode == RATE_MODE_HT_MIX || |
| 813 |
rxdesc.rate_mode == RATE_MODE_HT_GREENFIELD) |
| 814 |
rxdesc.encoding = RX_ENC_HT; |
| 815 |
|
| 816 |
/* |
| 817 |
* Check if this is a beacon, and more frames have been |
| 818 |
* buffered while we were in powersaving mode. |
| 819 |
*/ |
| 820 |
rt2x00lib_rxdone_check_ps(rt2x00dev, entry->skb, &rxdesc); |
| 821 |
|
| 822 |
/* |
| 823 |
* Check for incoming BlockAcks to match to the BlockAckReqs |
| 824 |
* we've send out. |
| 825 |
*/ |
| 826 |
rt2x00lib_rxdone_check_ba(rt2x00dev, entry->skb, &rxdesc); |
| 827 |
|
| 828 |
/* |
| 829 |
* Update extra components |
| 830 |
*/ |
| 831 |
rt2x00link_update_stats(rt2x00dev, entry->skb, &rxdesc); |
| 832 |
rt2x00debug_update_crypto(rt2x00dev, &rxdesc); |
| 833 |
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_RXDONE, entry); |
| 834 |
|
| 835 |
/* |
| 836 |
* Initialize RX status information, and send frame |
| 837 |
* to mac80211. |
| 838 |
*/ |
| 839 |
rx_status = IEEE80211_SKB_RXCB(entry->skb); |
| 840 |
|
| 841 |
/* Ensure that all fields of rx_status are initialized |
| 842 |
* properly. The skb->cb array was used for driver |
| 843 |
* specific informations, so rx_status might contain |
| 844 |
* garbage. |
| 845 |
*/ |
| 846 |
memset(rx_status, 0, sizeof(*rx_status)); |
| 847 |
|
| 848 |
rx_status->mactime = rxdesc.timestamp; |
| 849 |
rx_status->band = rt2x00dev->curr_band; |
| 850 |
rx_status->freq = rt2x00dev->curr_freq; |
| 851 |
rx_status->rate_idx = rate_idx; |
| 852 |
rx_status->signal = rxdesc.rssi; |
| 853 |
rx_status->flag = rxdesc.flags; |
| 854 |
rx_status->enc_flags = rxdesc.enc_flags; |
| 855 |
rx_status->encoding = rxdesc.encoding; |
| 856 |
rx_status->bw = rxdesc.bw; |
| 857 |
rx_status->antenna = rt2x00dev->link.ant.active.rx; |
| 858 |
|
| 859 |
ieee80211_rx_ni(rt2x00dev->hw, entry->skb); |
| 860 |
|
| 861 |
renew_skb: |
| 862 |
/* |
| 863 |
* Replace the skb with the freshly allocated one. |
| 864 |
*/ |
| 865 |
entry->skb = skb; |
| 866 |
|
| 867 |
submit_entry: |
| 868 |
entry->flags = 0; |
| 869 |
rt2x00queue_index_inc(entry, Q_INDEX_DONE); |
| 870 |
if (test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) && |
| 871 |
test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) |
| 872 |
rt2x00dev->ops->lib->clear_entry(entry); |
| 873 |
} |
| 874 |
EXPORT_SYMBOL_GPL(rt2x00lib_rxdone); |
| 875 |
|
| 876 |
/* |
| 877 |
* Driver initialization handlers. |
| 878 |
*/ |
| 879 |
const struct rt2x00_rate rt2x00_supported_rates[12] = { |
| 880 |
{ |
| 881 |
.flags = DEV_RATE_CCK, |
| 882 |
.bitrate = 10, |
| 883 |
.ratemask = BIT(0), |
| 884 |
.plcp = 0x00, |
| 885 |
.mcs = RATE_MCS(RATE_MODE_CCK, 0), |
| 886 |
}, |
| 887 |
{ |
| 888 |
.flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE, |
| 889 |
.bitrate = 20, |
| 890 |
.ratemask = BIT(1), |
| 891 |
.plcp = 0x01, |
| 892 |
.mcs = RATE_MCS(RATE_MODE_CCK, 1), |
| 893 |
}, |
| 894 |
{ |
| 895 |
.flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE, |
| 896 |
.bitrate = 55, |
| 897 |
.ratemask = BIT(2), |
| 898 |
.plcp = 0x02, |
| 899 |
.mcs = RATE_MCS(RATE_MODE_CCK, 2), |
| 900 |
}, |
| 901 |
{ |
| 902 |
.flags = DEV_RATE_CCK | DEV_RATE_SHORT_PREAMBLE, |
| 903 |
.bitrate = 110, |
| 904 |
.ratemask = BIT(3), |
| 905 |
.plcp = 0x03, |
| 906 |
.mcs = RATE_MCS(RATE_MODE_CCK, 3), |
| 907 |
}, |
| 908 |
{ |
| 909 |
.flags = DEV_RATE_OFDM, |
| 910 |
.bitrate = 60, |
| 911 |
.ratemask = BIT(4), |
| 912 |
.plcp = 0x0b, |
| 913 |
.mcs = RATE_MCS(RATE_MODE_OFDM, 0), |
| 914 |
}, |
| 915 |
{ |
| 916 |
.flags = DEV_RATE_OFDM, |
| 917 |
.bitrate = 90, |
| 918 |
.ratemask = BIT(5), |
| 919 |
.plcp = 0x0f, |
| 920 |
.mcs = RATE_MCS(RATE_MODE_OFDM, 1), |
| 921 |
}, |
| 922 |
{ |
| 923 |
.flags = DEV_RATE_OFDM, |
| 924 |
.bitrate = 120, |
| 925 |
.ratemask = BIT(6), |
| 926 |
.plcp = 0x0a, |
| 927 |
.mcs = RATE_MCS(RATE_MODE_OFDM, 2), |
| 928 |
}, |
| 929 |
{ |
| 930 |
.flags = DEV_RATE_OFDM, |
| 931 |
.bitrate = 180, |
| 932 |
.ratemask = BIT(7), |
| 933 |
.plcp = 0x0e, |
| 934 |
.mcs = RATE_MCS(RATE_MODE_OFDM, 3), |
| 935 |
}, |
| 936 |
{ |
| 937 |
.flags = DEV_RATE_OFDM, |
| 938 |
.bitrate = 240, |
| 939 |
.ratemask = BIT(8), |
| 940 |
.plcp = 0x09, |
| 941 |
.mcs = RATE_MCS(RATE_MODE_OFDM, 4), |
| 942 |
}, |
| 943 |
{ |
| 944 |
.flags = DEV_RATE_OFDM, |
| 945 |
.bitrate = 360, |
| 946 |
.ratemask = BIT(9), |
| 947 |
.plcp = 0x0d, |
| 948 |
.mcs = RATE_MCS(RATE_MODE_OFDM, 5), |
| 949 |
}, |
| 950 |
{ |
| 951 |
.flags = DEV_RATE_OFDM, |
| 952 |
.bitrate = 480, |
| 953 |
.ratemask = BIT(10), |
| 954 |
.plcp = 0x08, |
| 955 |
.mcs = RATE_MCS(RATE_MODE_OFDM, 6), |
| 956 |
}, |
| 957 |
{ |
| 958 |
.flags = DEV_RATE_OFDM, |
| 959 |
.bitrate = 540, |
| 960 |
.ratemask = BIT(11), |
| 961 |
.plcp = 0x0c, |
| 962 |
.mcs = RATE_MCS(RATE_MODE_OFDM, 7), |
| 963 |
}, |
| 964 |
}; |
| 965 |
|
| 966 |
static void rt2x00lib_channel(struct ieee80211_channel *entry, |
| 967 |
const int channel, const int tx_power, |
| 968 |
const int value) |
| 969 |
{ |
| 970 |
/* XXX: this assumption about the band is wrong for 802.11j */ |
| 971 |
entry->band = channel <= 14 ? NL80211_BAND_2GHZ : NL80211_BAND_5GHZ; |
| 972 |
entry->center_freq = ieee80211_channel_to_frequency(channel, |
| 973 |
entry->band); |
| 974 |
entry->hw_value = value; |
| 975 |
entry->max_power = tx_power; |
| 976 |
entry->max_antenna_gain = 0xff; |
| 977 |
} |
| 978 |
|
| 979 |
static void rt2x00lib_rate(struct ieee80211_rate *entry, |
| 980 |
const u16 index, const struct rt2x00_rate *rate) |
| 981 |
{ |
| 982 |
entry->flags = 0; |
| 983 |
entry->bitrate = rate->bitrate; |
| 984 |
entry->hw_value = index; |
| 985 |
entry->hw_value_short = index; |
| 986 |
|
| 987 |
if (rate->flags & DEV_RATE_SHORT_PREAMBLE) |
| 988 |
entry->flags |= IEEE80211_RATE_SHORT_PREAMBLE; |
| 989 |
} |
| 990 |
|
| 991 |
int rt2x00lib_set_mac_address(struct rt2x00_dev *rt2x00dev, u8 *eeprom_mac_addr) |
| 992 |
{ |
| 993 |
int ret; |
| 994 |
|
| 995 |
ret = of_get_mac_address(rt2x00dev->dev->of_node, eeprom_mac_addr); |
| 996 |
if (ret == -EPROBE_DEFER) |
| 997 |
return ret; |
| 998 |
|
| 999 |
if (!is_valid_ether_addr(eeprom_mac_addr)) { |
| 1000 |
eth_random_addr(eeprom_mac_addr); |
| 1001 |
rt2x00_eeprom_dbg(rt2x00dev, "MAC: %pM\n", eeprom_mac_addr); |
| 1002 |
} |
| 1003 |
|
| 1004 |
return 0; |
| 1005 |
} |
| 1006 |
EXPORT_SYMBOL_GPL(rt2x00lib_set_mac_address); |
| 1007 |
|
| 1008 |
static int rt2x00lib_probe_hw_modes(struct rt2x00_dev *rt2x00dev, |
| 1009 |
struct hw_mode_spec *spec) |
| 1010 |
{ |
| 1011 |
struct ieee80211_hw *hw = rt2x00dev->hw; |
| 1012 |
struct ieee80211_channel *channels; |
| 1013 |
struct ieee80211_rate *rates; |
| 1014 |
unsigned int num_rates; |
| 1015 |
unsigned int i; |
| 1016 |
|
| 1017 |
num_rates = 0; |
| 1018 |
if (spec->supported_rates & SUPPORT_RATE_CCK) |
| 1019 |
num_rates += 4; |
| 1020 |
if (spec->supported_rates & SUPPORT_RATE_OFDM) |
| 1021 |
num_rates += 8; |
| 1022 |
|
| 1023 |
channels = kzalloc_objs(*channels, spec->num_channels); |
| 1024 |
if (!channels) |
| 1025 |
return -ENOMEM; |
| 1026 |
|
| 1027 |
rates = kzalloc_objs(*rates, num_rates); |
| 1028 |
if (!rates) |
| 1029 |
goto exit_free_channels; |
| 1030 |
|
| 1031 |
/* |
| 1032 |
* Initialize Rate list. |
| 1033 |
*/ |
| 1034 |
for (i = 0; i < num_rates; i++) |
| 1035 |
rt2x00lib_rate(&rates[i], i, rt2x00_get_rate(i)); |
| 1036 |
|
| 1037 |
/* |
| 1038 |
* Initialize Channel list. |
| 1039 |
*/ |
| 1040 |
for (i = 0; i < spec->num_channels; i++) { |
| 1041 |
rt2x00lib_channel(&channels[i], |
| 1042 |
spec->channels[i].channel, |
| 1043 |
spec->channels_info[i].max_power, i); |
| 1044 |
} |
| 1045 |
|
| 1046 |
/* |
| 1047 |
* Intitialize 802.11b, 802.11g |
| 1048 |
* Rates: CCK, OFDM. |
| 1049 |
* Channels: 2.4 GHz |
| 1050 |
*/ |
| 1051 |
if (spec->supported_bands & SUPPORT_BAND_2GHZ) { |
| 1052 |
rt2x00dev->bands[NL80211_BAND_2GHZ].n_channels = 14; |
| 1053 |
rt2x00dev->bands[NL80211_BAND_2GHZ].n_bitrates = num_rates; |
| 1054 |
rt2x00dev->bands[NL80211_BAND_2GHZ].channels = channels; |
| 1055 |
rt2x00dev->bands[NL80211_BAND_2GHZ].bitrates = rates; |
| 1056 |
hw->wiphy->bands[NL80211_BAND_2GHZ] = |
| 1057 |
&rt2x00dev->bands[NL80211_BAND_2GHZ]; |
| 1058 |
memcpy(&rt2x00dev->bands[NL80211_BAND_2GHZ].ht_cap, |
| 1059 |
&spec->ht, sizeof(spec->ht)); |
| 1060 |
} |
| 1061 |
|
| 1062 |
/* |
| 1063 |
* Intitialize 802.11a |
| 1064 |
* Rates: OFDM. |
| 1065 |
* Channels: OFDM, UNII, HiperLAN2. |
| 1066 |
*/ |
| 1067 |
if (spec->supported_bands & SUPPORT_BAND_5GHZ) { |
| 1068 |
rt2x00dev->bands[NL80211_BAND_5GHZ].n_channels = |
| 1069 |
spec->num_channels - 14; |
| 1070 |
rt2x00dev->bands[NL80211_BAND_5GHZ].n_bitrates = |
| 1071 |
num_rates - 4; |
| 1072 |
rt2x00dev->bands[NL80211_BAND_5GHZ].channels = &channels[14]; |
| 1073 |
rt2x00dev->bands[NL80211_BAND_5GHZ].bitrates = &rates[4]; |
| 1074 |
hw->wiphy->bands[NL80211_BAND_5GHZ] = |
| 1075 |
&rt2x00dev->bands[NL80211_BAND_5GHZ]; |
| 1076 |
memcpy(&rt2x00dev->bands[NL80211_BAND_5GHZ].ht_cap, |
| 1077 |
&spec->ht, sizeof(spec->ht)); |
| 1078 |
} |
| 1079 |
|
| 1080 |
return 0; |
| 1081 |
|
| 1082 |
exit_free_channels: |
| 1083 |
kfree(channels); |
| 1084 |
rt2x00_err(rt2x00dev, "Allocation ieee80211 modes failed\n"); |
| 1085 |
return -ENOMEM; |
| 1086 |
} |
| 1087 |
|
| 1088 |
static void rt2x00lib_remove_hw(struct rt2x00_dev *rt2x00dev) |
| 1089 |
{ |
| 1090 |
if (test_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags)) |
| 1091 |
ieee80211_unregister_hw(rt2x00dev->hw); |
| 1092 |
|
| 1093 |
if (likely(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ])) { |
| 1094 |
kfree(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ]->channels); |
| 1095 |
kfree(rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ]->bitrates); |
| 1096 |
rt2x00dev->hw->wiphy->bands[NL80211_BAND_2GHZ] = NULL; |
| 1097 |
rt2x00dev->hw->wiphy->bands[NL80211_BAND_5GHZ] = NULL; |
| 1098 |
} |
| 1099 |
|
| 1100 |
kfree(rt2x00dev->spec.channels_info); |
| 1101 |
kfree(rt2x00dev->chan_survey); |
| 1102 |
} |
| 1103 |
|
| 1104 |
static const struct ieee80211_tpt_blink rt2x00_tpt_blink[] = { |
| 1105 |
{ .throughput = 0 * 1024, .blink_time = 334 }, |
| 1106 |
{ .throughput = 1 * 1024, .blink_time = 260 }, |
| 1107 |
{ .throughput = 2 * 1024, .blink_time = 220 }, |
| 1108 |
{ .throughput = 5 * 1024, .blink_time = 190 }, |
| 1109 |
{ .throughput = 10 * 1024, .blink_time = 170 }, |
| 1110 |
{ .throughput = 25 * 1024, .blink_time = 150 }, |
| 1111 |
{ .throughput = 54 * 1024, .blink_time = 130 }, |
| 1112 |
{ .throughput = 120 * 1024, .blink_time = 110 }, |
| 1113 |
{ .throughput = 265 * 1024, .blink_time = 80 }, |
| 1114 |
{ .throughput = 586 * 1024, .blink_time = 50 }, |
| 1115 |
}; |
| 1116 |
|
| 1117 |
static int rt2x00lib_probe_hw(struct rt2x00_dev *rt2x00dev) |
| 1118 |
{ |
| 1119 |
struct hw_mode_spec *spec = &rt2x00dev->spec; |
| 1120 |
int status; |
| 1121 |
|
| 1122 |
if (test_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags)) |
| 1123 |
return 0; |
| 1124 |
|
| 1125 |
/* |
| 1126 |
* Initialize HW modes. |
| 1127 |
*/ |
| 1128 |
status = rt2x00lib_probe_hw_modes(rt2x00dev, spec); |
| 1129 |
if (status) |
| 1130 |
return status; |
| 1131 |
|
| 1132 |
/* |
| 1133 |
* Initialize HW fields. |
| 1134 |
*/ |
| 1135 |
rt2x00dev->hw->queues = rt2x00dev->ops->tx_queues; |
| 1136 |
|
| 1137 |
/* |
| 1138 |
* Initialize extra TX headroom required. |
| 1139 |
*/ |
| 1140 |
rt2x00dev->hw->extra_tx_headroom = |
| 1141 |
max_t(unsigned int, IEEE80211_TX_STATUS_HEADROOM, |
| 1142 |
rt2x00dev->extra_tx_headroom); |
| 1143 |
|
| 1144 |
/* |
| 1145 |
* Take TX headroom required for alignment into account. |
| 1146 |
*/ |
| 1147 |
if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_L2PAD)) |
| 1148 |
rt2x00dev->hw->extra_tx_headroom += RT2X00_L2PAD_SIZE; |
| 1149 |
else if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DMA)) |
| 1150 |
rt2x00dev->hw->extra_tx_headroom += RT2X00_ALIGN_SIZE; |
| 1151 |
|
| 1152 |
/* |
| 1153 |
* Tell mac80211 about the size of our private STA structure. |
| 1154 |
*/ |
| 1155 |
rt2x00dev->hw->sta_data_size = sizeof(struct rt2x00_sta); |
| 1156 |
|
| 1157 |
/* |
| 1158 |
* Allocate tx status FIFO for driver use. |
| 1159 |
*/ |
| 1160 |
if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_TXSTATUS_FIFO)) { |
| 1161 |
/* |
| 1162 |
* Allocate the txstatus fifo. In the worst case the tx |
| 1163 |
* status fifo has to hold the tx status of all entries |
| 1164 |
* in all tx queues. Hence, calculate the kfifo size as |
| 1165 |
* tx_queues * entry_num and round up to the nearest |
| 1166 |
* power of 2. |
| 1167 |
*/ |
| 1168 |
int kfifo_size = |
| 1169 |
roundup_pow_of_two(rt2x00dev->ops->tx_queues * |
| 1170 |
rt2x00dev->tx->limit * |
| 1171 |
sizeof(u32)); |
| 1172 |
|
| 1173 |
status = kfifo_alloc(&rt2x00dev->txstatus_fifo, kfifo_size, |
| 1174 |
GFP_KERNEL); |
| 1175 |
if (status) |
| 1176 |
return status; |
| 1177 |
} |
| 1178 |
|
| 1179 |
/* |
| 1180 |
* Initialize tasklets if used by the driver. Tasklets are |
| 1181 |
* disabled until the interrupts are turned on. The driver |
| 1182 |
* has to handle that. |
| 1183 |
*/ |
| 1184 |
#define RT2X00_TASKLET_INIT(taskletname) \ |
| 1185 |
if (rt2x00dev->ops->lib->taskletname) { \ |
| 1186 |
tasklet_setup(&rt2x00dev->taskletname, \ |
| 1187 |
rt2x00dev->ops->lib->taskletname); \ |
| 1188 |
} |
| 1189 |
|
| 1190 |
RT2X00_TASKLET_INIT(txstatus_tasklet); |
| 1191 |
RT2X00_TASKLET_INIT(pretbtt_tasklet); |
| 1192 |
RT2X00_TASKLET_INIT(tbtt_tasklet); |
| 1193 |
RT2X00_TASKLET_INIT(rxdone_tasklet); |
| 1194 |
RT2X00_TASKLET_INIT(autowake_tasklet); |
| 1195 |
|
| 1196 |
#undef RT2X00_TASKLET_INIT |
| 1197 |
|
| 1198 |
ieee80211_create_tpt_led_trigger(rt2x00dev->hw, |
| 1199 |
IEEE80211_TPT_LEDTRIG_FL_RADIO, |
| 1200 |
rt2x00_tpt_blink, |
| 1201 |
ARRAY_SIZE(rt2x00_tpt_blink)); |
| 1202 |
|
| 1203 |
/* |
| 1204 |
* Register HW. |
| 1205 |
*/ |
| 1206 |
status = ieee80211_register_hw(rt2x00dev->hw); |
| 1207 |
if (status) |
| 1208 |
return status; |
| 1209 |
|
| 1210 |
set_bit(DEVICE_STATE_REGISTERED_HW, &rt2x00dev->flags); |
| 1211 |
|
| 1212 |
return 0; |
| 1213 |
} |
| 1214 |
|
| 1215 |
/* |
| 1216 |
* Initialization/uninitialization handlers. |
| 1217 |
*/ |
| 1218 |
static void rt2x00lib_uninitialize(struct rt2x00_dev *rt2x00dev) |
| 1219 |
{ |
| 1220 |
if (!test_and_clear_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags)) |
| 1221 |
return; |
| 1222 |
|
| 1223 |
/* |
| 1224 |
* Stop rfkill polling. |
| 1225 |
*/ |
| 1226 |
if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL)) |
| 1227 |
rt2x00rfkill_unregister(rt2x00dev); |
| 1228 |
|
| 1229 |
/* |
| 1230 |
* Allow the HW to uninitialize. |
| 1231 |
*/ |
| 1232 |
rt2x00dev->ops->lib->uninitialize(rt2x00dev); |
| 1233 |
|
| 1234 |
/* |
| 1235 |
* Free allocated queue entries. |
| 1236 |
*/ |
| 1237 |
rt2x00queue_uninitialize(rt2x00dev); |
| 1238 |
} |
| 1239 |
|
| 1240 |
static int rt2x00lib_initialize(struct rt2x00_dev *rt2x00dev) |
| 1241 |
{ |
| 1242 |
int status; |
| 1243 |
|
| 1244 |
if (test_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags)) |
| 1245 |
return 0; |
| 1246 |
|
| 1247 |
/* |
| 1248 |
* Allocate all queue entries. |
| 1249 |
*/ |
| 1250 |
status = rt2x00queue_initialize(rt2x00dev); |
| 1251 |
if (status) |
| 1252 |
return status; |
| 1253 |
|
| 1254 |
/* |
| 1255 |
* Initialize the device. |
| 1256 |
*/ |
| 1257 |
status = rt2x00dev->ops->lib->initialize(rt2x00dev); |
| 1258 |
if (status) { |
| 1259 |
rt2x00queue_uninitialize(rt2x00dev); |
| 1260 |
return status; |
| 1261 |
} |
| 1262 |
|
| 1263 |
set_bit(DEVICE_STATE_INITIALIZED, &rt2x00dev->flags); |
| 1264 |
|
| 1265 |
/* |
| 1266 |
* Start rfkill polling. |
| 1267 |
*/ |
| 1268 |
if (rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL)) |
| 1269 |
rt2x00rfkill_register(rt2x00dev); |
| 1270 |
|
| 1271 |
return 0; |
| 1272 |
} |
| 1273 |
|
| 1274 |
int rt2x00lib_start(struct rt2x00_dev *rt2x00dev) |
| 1275 |
{ |
| 1276 |
int retval = 0; |
| 1277 |
|
| 1278 |
/* |
| 1279 |
* If this is the first interface which is added, |
| 1280 |
* we should load the firmware now. |
| 1281 |
*/ |
| 1282 |
retval = rt2x00lib_load_firmware(rt2x00dev); |
| 1283 |
if (retval) |
| 1284 |
goto out; |
| 1285 |
|
| 1286 |
/* |
| 1287 |
* Initialize the device. |
| 1288 |
*/ |
| 1289 |
retval = rt2x00lib_initialize(rt2x00dev); |
| 1290 |
if (retval) |
| 1291 |
goto out; |
| 1292 |
|
| 1293 |
rt2x00dev->intf_ap_count = 0; |
| 1294 |
rt2x00dev->intf_sta_count = 0; |
| 1295 |
rt2x00dev->intf_associated = 0; |
| 1296 |
rt2x00dev->intf_beaconing = 0; |
| 1297 |
|
| 1298 |
/* Enable the radio */ |
| 1299 |
retval = rt2x00lib_enable_radio(rt2x00dev); |
| 1300 |
if (retval) |
| 1301 |
goto out; |
| 1302 |
|
| 1303 |
set_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags); |
| 1304 |
|
| 1305 |
out: |
| 1306 |
return retval; |
| 1307 |
} |
| 1308 |
|
| 1309 |
void rt2x00lib_stop(struct rt2x00_dev *rt2x00dev) |
| 1310 |
{ |
| 1311 |
if (!test_and_clear_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags)) |
| 1312 |
return; |
| 1313 |
|
| 1314 |
/* |
| 1315 |
* Perhaps we can add something smarter here, |
| 1316 |
* but for now just disabling the radio should do. |
| 1317 |
*/ |
| 1318 |
rt2x00lib_disable_radio(rt2x00dev); |
| 1319 |
|
| 1320 |
rt2x00dev->intf_ap_count = 0; |
| 1321 |
rt2x00dev->intf_sta_count = 0; |
| 1322 |
rt2x00dev->intf_associated = 0; |
| 1323 |
rt2x00dev->intf_beaconing = 0; |
| 1324 |
} |
| 1325 |
|
| 1326 |
static inline void rt2x00lib_set_if_combinations(struct rt2x00_dev *rt2x00dev) |
| 1327 |
{ |
| 1328 |
struct ieee80211_iface_limit *if_limit; |
| 1329 |
struct ieee80211_iface_combination *if_combination; |
| 1330 |
|
| 1331 |
if (rt2x00dev->ops->max_ap_intf < 2) |
| 1332 |
return; |
| 1333 |
|
| 1334 |
/* |
| 1335 |
* Build up AP interface limits structure. |
| 1336 |
*/ |
| 1337 |
if_limit = &rt2x00dev->if_limits_ap; |
| 1338 |
if_limit->max = rt2x00dev->ops->max_ap_intf; |
| 1339 |
if_limit->types = BIT(NL80211_IFTYPE_AP); |
| 1340 |
#ifdef CONFIG_MAC80211_MESH |
| 1341 |
if_limit->types |= BIT(NL80211_IFTYPE_MESH_POINT); |
| 1342 |
#endif |
| 1343 |
|
| 1344 |
/* |
| 1345 |
* Build up AP interface combinations structure. |
| 1346 |
*/ |
| 1347 |
if_combination = &rt2x00dev->if_combinations[IF_COMB_AP]; |
| 1348 |
if_combination->limits = if_limit; |
| 1349 |
if_combination->n_limits = 1; |
| 1350 |
if_combination->max_interfaces = if_limit->max; |
| 1351 |
if_combination->num_different_channels = 1; |
| 1352 |
|
| 1353 |
/* |
| 1354 |
* Finally, specify the possible combinations to mac80211. |
| 1355 |
*/ |
| 1356 |
rt2x00dev->hw->wiphy->iface_combinations = rt2x00dev->if_combinations; |
| 1357 |
rt2x00dev->hw->wiphy->n_iface_combinations = 1; |
| 1358 |
} |
| 1359 |
|
| 1360 |
static unsigned int rt2x00dev_extra_tx_headroom(struct rt2x00_dev *rt2x00dev) |
| 1361 |
{ |
| 1362 |
if (WARN_ON(!rt2x00dev->tx)) |
| 1363 |
return 0; |
| 1364 |
|
| 1365 |
if (rt2x00_is_usb(rt2x00dev)) |
| 1366 |
return rt2x00dev->tx[0].winfo_size + rt2x00dev->tx[0].desc_size; |
| 1367 |
|
| 1368 |
return rt2x00dev->tx[0].winfo_size; |
| 1369 |
} |
| 1370 |
|
| 1371 |
/* |
| 1372 |
* driver allocation handlers. |
| 1373 |
*/ |
| 1374 |
int rt2x00lib_probe_dev(struct rt2x00_dev *rt2x00dev) |
| 1375 |
{ |
| 1376 |
int retval = -ENOMEM; |
| 1377 |
|
| 1378 |
/* |
| 1379 |
* Set possible interface combinations. |
| 1380 |
*/ |
| 1381 |
rt2x00lib_set_if_combinations(rt2x00dev); |
| 1382 |
|
| 1383 |
/* |
| 1384 |
* Allocate the driver data memory, if necessary. |
| 1385 |
*/ |
| 1386 |
if (rt2x00dev->ops->drv_data_size > 0) { |
| 1387 |
rt2x00dev->drv_data = kzalloc(rt2x00dev->ops->drv_data_size, |
| 1388 |
GFP_KERNEL); |
| 1389 |
if (!rt2x00dev->drv_data) { |
| 1390 |
retval = -ENOMEM; |
| 1391 |
goto exit; |
| 1392 |
} |
| 1393 |
} |
| 1394 |
|
| 1395 |
spin_lock_init(&rt2x00dev->irqmask_lock); |
| 1396 |
mutex_init(&rt2x00dev->csr_mutex); |
| 1397 |
mutex_init(&rt2x00dev->conf_mutex); |
| 1398 |
INIT_LIST_HEAD(&rt2x00dev->bar_list); |
| 1399 |
spin_lock_init(&rt2x00dev->bar_list_lock); |
| 1400 |
hrtimer_setup(&rt2x00dev->txstatus_timer, hrtimer_dummy_timeout, CLOCK_MONOTONIC, |
| 1401 |
HRTIMER_MODE_REL); |
| 1402 |
|
| 1403 |
set_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags); |
| 1404 |
|
| 1405 |
/* |
| 1406 |
* Make room for rt2x00_intf inside the per-interface |
| 1407 |
* structure ieee80211_vif. |
| 1408 |
*/ |
| 1409 |
rt2x00dev->hw->vif_data_size = sizeof(struct rt2x00_intf); |
| 1410 |
|
| 1411 |
/* |
| 1412 |
* rt2x00 devices can only use the last n bits of the MAC address |
| 1413 |
* for virtual interfaces. |
| 1414 |
*/ |
| 1415 |
rt2x00dev->hw->wiphy->addr_mask[ETH_ALEN - 1] = |
| 1416 |
(rt2x00dev->ops->max_ap_intf - 1); |
| 1417 |
|
| 1418 |
/* |
| 1419 |
* Initialize work. |
| 1420 |
*/ |
| 1421 |
rt2x00dev->workqueue = |
| 1422 |
alloc_ordered_workqueue("%s", 0, wiphy_name(rt2x00dev->hw->wiphy)); |
| 1423 |
if (!rt2x00dev->workqueue) { |
| 1424 |
retval = -ENOMEM; |
| 1425 |
goto exit; |
| 1426 |
} |
| 1427 |
|
| 1428 |
INIT_WORK(&rt2x00dev->intf_work, rt2x00lib_intf_scheduled); |
| 1429 |
INIT_DELAYED_WORK(&rt2x00dev->autowakeup_work, rt2x00lib_autowakeup); |
| 1430 |
INIT_WORK(&rt2x00dev->sleep_work, rt2x00lib_sleep); |
| 1431 |
|
| 1432 |
/* |
| 1433 |
* Let the driver probe the device to detect the capabilities. |
| 1434 |
*/ |
| 1435 |
retval = rt2x00dev->ops->lib->probe_hw(rt2x00dev); |
| 1436 |
if (retval) { |
| 1437 |
rt2x00_err(rt2x00dev, "Failed to allocate device\n"); |
| 1438 |
goto exit; |
| 1439 |
} |
| 1440 |
|
| 1441 |
/* |
| 1442 |
* Allocate queue array. |
| 1443 |
*/ |
| 1444 |
retval = rt2x00queue_allocate(rt2x00dev); |
| 1445 |
if (retval) |
| 1446 |
goto exit; |
| 1447 |
|
| 1448 |
/* Cache TX headroom value */ |
| 1449 |
rt2x00dev->extra_tx_headroom = rt2x00dev_extra_tx_headroom(rt2x00dev); |
| 1450 |
|
| 1451 |
/* |
| 1452 |
* Determine which operating modes are supported, all modes |
| 1453 |
* which require beaconing, depend on the availability of |
| 1454 |
* beacon entries. |
| 1455 |
*/ |
| 1456 |
rt2x00dev->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION); |
| 1457 |
if (rt2x00dev->bcn->limit > 0) |
| 1458 |
rt2x00dev->hw->wiphy->interface_modes |= |
| 1459 |
BIT(NL80211_IFTYPE_ADHOC) | |
| 1460 |
#ifdef CONFIG_MAC80211_MESH |
| 1461 |
BIT(NL80211_IFTYPE_MESH_POINT) | |
| 1462 |
#endif |
| 1463 |
BIT(NL80211_IFTYPE_AP); |
| 1464 |
|
| 1465 |
rt2x00dev->hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN; |
| 1466 |
|
| 1467 |
wiphy_ext_feature_set(rt2x00dev->hw->wiphy, |
| 1468 |
NL80211_EXT_FEATURE_CQM_RSSI_LIST); |
| 1469 |
|
| 1470 |
/* |
| 1471 |
* Initialize ieee80211 structure. |
| 1472 |
*/ |
| 1473 |
retval = rt2x00lib_probe_hw(rt2x00dev); |
| 1474 |
if (retval) { |
| 1475 |
rt2x00_err(rt2x00dev, "Failed to initialize hw\n"); |
| 1476 |
goto exit; |
| 1477 |
} |
| 1478 |
|
| 1479 |
/* |
| 1480 |
* Register extra components. |
| 1481 |
*/ |
| 1482 |
rt2x00link_register(rt2x00dev); |
| 1483 |
rt2x00leds_register(rt2x00dev); |
| 1484 |
rt2x00debug_register(rt2x00dev); |
| 1485 |
|
| 1486 |
/* |
| 1487 |
* Start rfkill polling. |
| 1488 |
*/ |
| 1489 |
if (!rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL)) |
| 1490 |
rt2x00rfkill_register(rt2x00dev); |
| 1491 |
|
| 1492 |
return 0; |
| 1493 |
|
| 1494 |
exit: |
| 1495 |
rt2x00lib_remove_dev(rt2x00dev); |
| 1496 |
|
| 1497 |
return retval; |
| 1498 |
} |
| 1499 |
EXPORT_SYMBOL_GPL(rt2x00lib_probe_dev); |
| 1500 |
|
| 1501 |
void rt2x00lib_remove_dev(struct rt2x00_dev *rt2x00dev) |
| 1502 |
{ |
| 1503 |
clear_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags); |
| 1504 |
|
| 1505 |
/* |
| 1506 |
* Stop rfkill polling. |
| 1507 |
*/ |
| 1508 |
if (!rt2x00_has_cap_flag(rt2x00dev, REQUIRE_DELAYED_RFKILL)) |
| 1509 |
rt2x00rfkill_unregister(rt2x00dev); |
| 1510 |
|
| 1511 |
/* |
| 1512 |
* Disable radio. |
| 1513 |
*/ |
| 1514 |
rt2x00lib_disable_radio(rt2x00dev); |
| 1515 |
|
| 1516 |
/* |
| 1517 |
* Stop all work. |
| 1518 |
*/ |
| 1519 |
cancel_work_sync(&rt2x00dev->intf_work); |
| 1520 |
cancel_delayed_work_sync(&rt2x00dev->autowakeup_work); |
| 1521 |
cancel_work_sync(&rt2x00dev->sleep_work); |
| 1522 |
|
| 1523 |
hrtimer_cancel(&rt2x00dev->txstatus_timer); |
| 1524 |
|
| 1525 |
/* |
| 1526 |
* Kill the tx status tasklet. |
| 1527 |
*/ |
| 1528 |
tasklet_kill(&rt2x00dev->txstatus_tasklet); |
| 1529 |
tasklet_kill(&rt2x00dev->pretbtt_tasklet); |
| 1530 |
tasklet_kill(&rt2x00dev->tbtt_tasklet); |
| 1531 |
tasklet_kill(&rt2x00dev->rxdone_tasklet); |
| 1532 |
tasklet_kill(&rt2x00dev->autowake_tasklet); |
| 1533 |
|
| 1534 |
/* |
| 1535 |
* Uninitialize device. |
| 1536 |
*/ |
| 1537 |
rt2x00lib_uninitialize(rt2x00dev); |
| 1538 |
|
| 1539 |
if (rt2x00dev->workqueue) |
| 1540 |
destroy_workqueue(rt2x00dev->workqueue); |
| 1541 |
|
| 1542 |
/* |
| 1543 |
* Free the tx status fifo. |
| 1544 |
*/ |
| 1545 |
kfifo_free(&rt2x00dev->txstatus_fifo); |
| 1546 |
|
| 1547 |
/* |
| 1548 |
* Free extra components |
| 1549 |
*/ |
| 1550 |
rt2x00debug_deregister(rt2x00dev); |
| 1551 |
rt2x00leds_unregister(rt2x00dev); |
| 1552 |
|
| 1553 |
/* |
| 1554 |
* Free ieee80211_hw memory. |
| 1555 |
*/ |
| 1556 |
rt2x00lib_remove_hw(rt2x00dev); |
| 1557 |
|
| 1558 |
/* |
| 1559 |
* Free firmware image. |
| 1560 |
*/ |
| 1561 |
rt2x00lib_free_firmware(rt2x00dev); |
| 1562 |
|
| 1563 |
/* |
| 1564 |
* Free queue structures. |
| 1565 |
*/ |
| 1566 |
rt2x00queue_free(rt2x00dev); |
| 1567 |
|
| 1568 |
/* |
| 1569 |
* Free the driver data. |
| 1570 |
*/ |
| 1571 |
kfree(rt2x00dev->drv_data); |
| 1572 |
} |
| 1573 |
EXPORT_SYMBOL_GPL(rt2x00lib_remove_dev); |
| 1574 |
|
| 1575 |
/* |
| 1576 |
* Device state handlers |
| 1577 |
*/ |
| 1578 |
int rt2x00lib_suspend(struct rt2x00_dev *rt2x00dev) |
| 1579 |
{ |
| 1580 |
rt2x00_dbg(rt2x00dev, "Going to sleep\n"); |
| 1581 |
|
| 1582 |
/* |
| 1583 |
* Prevent mac80211 from accessing driver while suspended. |
| 1584 |
*/ |
| 1585 |
if (!test_and_clear_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags)) |
| 1586 |
return 0; |
| 1587 |
|
| 1588 |
/* |
| 1589 |
* Cleanup as much as possible. |
| 1590 |
*/ |
| 1591 |
rt2x00lib_uninitialize(rt2x00dev); |
| 1592 |
|
| 1593 |
/* |
| 1594 |
* Suspend/disable extra components. |
| 1595 |
*/ |
| 1596 |
rt2x00leds_suspend(rt2x00dev); |
| 1597 |
rt2x00debug_deregister(rt2x00dev); |
| 1598 |
|
| 1599 |
/* |
| 1600 |
* Set device mode to sleep for power management, |
| 1601 |
* on some hardware this call seems to consistently fail. |
| 1602 |
* From the specifications it is hard to tell why it fails, |
| 1603 |
* and if this is a "bad thing". |
| 1604 |
* Overall it is safe to just ignore the failure and |
| 1605 |
* continue suspending. The only downside is that the |
| 1606 |
* device will not be in optimal power save mode, but with |
| 1607 |
* the radio and the other components already disabled the |
| 1608 |
* device is as good as disabled. |
| 1609 |
*/ |
| 1610 |
if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_SLEEP)) |
| 1611 |
rt2x00_warn(rt2x00dev, "Device failed to enter sleep state, continue suspending\n"); |
| 1612 |
|
| 1613 |
return 0; |
| 1614 |
} |
| 1615 |
EXPORT_SYMBOL_GPL(rt2x00lib_suspend); |
| 1616 |
|
| 1617 |
int rt2x00lib_resume(struct rt2x00_dev *rt2x00dev) |
| 1618 |
{ |
| 1619 |
rt2x00_dbg(rt2x00dev, "Waking up\n"); |
| 1620 |
|
| 1621 |
/* |
| 1622 |
* Restore/enable extra components. |
| 1623 |
*/ |
| 1624 |
rt2x00debug_register(rt2x00dev); |
| 1625 |
rt2x00leds_resume(rt2x00dev); |
| 1626 |
|
| 1627 |
/* |
| 1628 |
* We are ready again to receive requests from mac80211. |
| 1629 |
*/ |
| 1630 |
set_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags); |
| 1631 |
|
| 1632 |
return 0; |
| 1633 |
} |
| 1634 |
EXPORT_SYMBOL_GPL(rt2x00lib_resume); |
| 1635 |
|
| 1636 |
/* |
| 1637 |
* rt2x00lib module information. |
| 1638 |
*/ |
| 1639 |
MODULE_AUTHOR(DRV_PROJECT); |
| 1640 |
MODULE_VERSION(DRV_VERSION); |
| 1641 |
MODULE_DESCRIPTION("rt2x00 library"); |
| 1642 |
MODULE_LICENSE("GPL"); |