| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
Copyright (C) 2004 - 2009 Ivo van Doorn <[email protected]> |
| 4 |
<http://rt2x00.serialmonkey.com> |
| 5 |
|
| 6 |
*/ |
| 7 |
|
| 8 |
/* |
| 9 |
Module: rt2500usb |
| 10 |
Abstract: rt2500usb device specific routines. |
| 11 |
Supported chipsets: RT2570. |
| 12 |
*/ |
| 13 |
|
| 14 |
#include <linux/delay.h> |
| 15 |
#include <linux/etherdevice.h> |
| 16 |
#include <linux/kernel.h> |
| 17 |
#include <linux/module.h> |
| 18 |
#include <linux/slab.h> |
| 19 |
#include <linux/usb.h> |
| 20 |
|
| 21 |
#include "rt2x00.h" |
| 22 |
#include "rt2x00usb.h" |
| 23 |
#include "rt2500usb.h" |
| 24 |
|
| 25 |
/* |
| 26 |
* Allow hardware encryption to be disabled. |
| 27 |
*/ |
| 28 |
static bool modparam_nohwcrypt; |
| 29 |
module_param_named(nohwcrypt, modparam_nohwcrypt, bool, 0444); |
| 30 |
MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); |
| 31 |
|
| 32 |
/* |
| 33 |
* Register access. |
| 34 |
* All access to the CSR registers will go through the methods |
| 35 |
* rt2500usb_register_read and rt2500usb_register_write. |
| 36 |
* BBP and RF register require indirect register access, |
| 37 |
* and use the CSR registers BBPCSR and RFCSR to achieve this. |
| 38 |
* These indirect registers work with busy bits, |
| 39 |
* and we will try maximal REGISTER_USB_BUSY_COUNT times to access |
| 40 |
* the register while taking a REGISTER_BUSY_DELAY us delay |
| 41 |
* between each attampt. When the busy bit is still set at that time, |
| 42 |
* the access attempt is considered to have failed, |
| 43 |
* and we will print an error. |
| 44 |
* If the csr_mutex is already held then the _lock variants must |
| 45 |
* be used instead. |
| 46 |
*/ |
| 47 |
static u16 rt2500usb_register_read(struct rt2x00_dev *rt2x00dev, |
| 48 |
const unsigned int offset) |
| 49 |
{ |
| 50 |
__le16 reg; |
| 51 |
rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_READ, |
| 52 |
USB_VENDOR_REQUEST_IN, offset, |
| 53 |
®, sizeof(reg)); |
| 54 |
return le16_to_cpu(reg); |
| 55 |
} |
| 56 |
|
| 57 |
static u16 rt2500usb_register_read_lock(struct rt2x00_dev *rt2x00dev, |
| 58 |
const unsigned int offset) |
| 59 |
{ |
| 60 |
__le16 reg; |
| 61 |
rt2x00usb_vendor_req_buff_lock(rt2x00dev, USB_MULTI_READ, |
| 62 |
USB_VENDOR_REQUEST_IN, offset, |
| 63 |
®, sizeof(reg), REGISTER_TIMEOUT); |
| 64 |
return le16_to_cpu(reg); |
| 65 |
} |
| 66 |
|
| 67 |
static void rt2500usb_register_write(struct rt2x00_dev *rt2x00dev, |
| 68 |
const unsigned int offset, |
| 69 |
u16 value) |
| 70 |
{ |
| 71 |
__le16 reg = cpu_to_le16(value); |
| 72 |
rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_WRITE, |
| 73 |
USB_VENDOR_REQUEST_OUT, offset, |
| 74 |
®, sizeof(reg)); |
| 75 |
} |
| 76 |
|
| 77 |
static void rt2500usb_register_write_lock(struct rt2x00_dev *rt2x00dev, |
| 78 |
const unsigned int offset, |
| 79 |
u16 value) |
| 80 |
{ |
| 81 |
__le16 reg = cpu_to_le16(value); |
| 82 |
rt2x00usb_vendor_req_buff_lock(rt2x00dev, USB_MULTI_WRITE, |
| 83 |
USB_VENDOR_REQUEST_OUT, offset, |
| 84 |
®, sizeof(reg), REGISTER_TIMEOUT); |
| 85 |
} |
| 86 |
|
| 87 |
static void rt2500usb_register_multiwrite(struct rt2x00_dev *rt2x00dev, |
| 88 |
const unsigned int offset, |
| 89 |
void *value, const u16 length) |
| 90 |
{ |
| 91 |
rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_WRITE, |
| 92 |
USB_VENDOR_REQUEST_OUT, offset, |
| 93 |
value, length); |
| 94 |
} |
| 95 |
|
| 96 |
static int rt2500usb_regbusy_read(struct rt2x00_dev *rt2x00dev, |
| 97 |
const unsigned int offset, |
| 98 |
struct rt2x00_field16 field, |
| 99 |
u16 *reg) |
| 100 |
{ |
| 101 |
unsigned int i; |
| 102 |
|
| 103 |
for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) { |
| 104 |
*reg = rt2500usb_register_read_lock(rt2x00dev, offset); |
| 105 |
if (!rt2x00_get_field16(*reg, field)) |
| 106 |
return 1; |
| 107 |
udelay(REGISTER_BUSY_DELAY); |
| 108 |
} |
| 109 |
|
| 110 |
rt2x00_err(rt2x00dev, "Indirect register access failed: offset=0x%.08x, value=0x%.08x\n", |
| 111 |
offset, *reg); |
| 112 |
*reg = ~0; |
| 113 |
|
| 114 |
return 0; |
| 115 |
} |
| 116 |
|
| 117 |
#define WAIT_FOR_BBP(__dev, __reg) \ |
| 118 |
rt2500usb_regbusy_read((__dev), PHY_CSR8, PHY_CSR8_BUSY, (__reg)) |
| 119 |
#define WAIT_FOR_RF(__dev, __reg) \ |
| 120 |
rt2500usb_regbusy_read((__dev), PHY_CSR10, PHY_CSR10_RF_BUSY, (__reg)) |
| 121 |
|
| 122 |
static void rt2500usb_bbp_write(struct rt2x00_dev *rt2x00dev, |
| 123 |
const unsigned int word, const u8 value) |
| 124 |
{ |
| 125 |
u16 reg; |
| 126 |
|
| 127 |
mutex_lock(&rt2x00dev->csr_mutex); |
| 128 |
|
| 129 |
/* |
| 130 |
* Wait until the BBP becomes available, afterwards we |
| 131 |
* can safely write the new data into the register. |
| 132 |
*/ |
| 133 |
if (WAIT_FOR_BBP(rt2x00dev, ®)) { |
| 134 |
reg = 0; |
| 135 |
rt2x00_set_field16(®, PHY_CSR7_DATA, value); |
| 136 |
rt2x00_set_field16(®, PHY_CSR7_REG_ID, word); |
| 137 |
rt2x00_set_field16(®, PHY_CSR7_READ_CONTROL, 0); |
| 138 |
|
| 139 |
rt2500usb_register_write_lock(rt2x00dev, PHY_CSR7, reg); |
| 140 |
} |
| 141 |
|
| 142 |
mutex_unlock(&rt2x00dev->csr_mutex); |
| 143 |
} |
| 144 |
|
| 145 |
static u8 rt2500usb_bbp_read(struct rt2x00_dev *rt2x00dev, |
| 146 |
const unsigned int word) |
| 147 |
{ |
| 148 |
u16 reg; |
| 149 |
u8 value; |
| 150 |
|
| 151 |
mutex_lock(&rt2x00dev->csr_mutex); |
| 152 |
|
| 153 |
/* |
| 154 |
* Wait until the BBP becomes available, afterwards we |
| 155 |
* can safely write the read request into the register. |
| 156 |
* After the data has been written, we wait until hardware |
| 157 |
* returns the correct value, if at any time the register |
| 158 |
* doesn't become available in time, reg will be 0xffffffff |
| 159 |
* which means we return 0xff to the caller. |
| 160 |
*/ |
| 161 |
if (WAIT_FOR_BBP(rt2x00dev, ®)) { |
| 162 |
reg = 0; |
| 163 |
rt2x00_set_field16(®, PHY_CSR7_REG_ID, word); |
| 164 |
rt2x00_set_field16(®, PHY_CSR7_READ_CONTROL, 1); |
| 165 |
|
| 166 |
rt2500usb_register_write_lock(rt2x00dev, PHY_CSR7, reg); |
| 167 |
|
| 168 |
if (WAIT_FOR_BBP(rt2x00dev, ®)) |
| 169 |
reg = rt2500usb_register_read_lock(rt2x00dev, PHY_CSR7); |
| 170 |
} |
| 171 |
|
| 172 |
value = rt2x00_get_field16(reg, PHY_CSR7_DATA); |
| 173 |
|
| 174 |
mutex_unlock(&rt2x00dev->csr_mutex); |
| 175 |
|
| 176 |
return value; |
| 177 |
} |
| 178 |
|
| 179 |
static void rt2500usb_rf_write(struct rt2x00_dev *rt2x00dev, |
| 180 |
const unsigned int word, const u32 value) |
| 181 |
{ |
| 182 |
u16 reg; |
| 183 |
|
| 184 |
mutex_lock(&rt2x00dev->csr_mutex); |
| 185 |
|
| 186 |
/* |
| 187 |
* Wait until the RF becomes available, afterwards we |
| 188 |
* can safely write the new data into the register. |
| 189 |
*/ |
| 190 |
if (WAIT_FOR_RF(rt2x00dev, ®)) { |
| 191 |
reg = 0; |
| 192 |
rt2x00_set_field16(®, PHY_CSR9_RF_VALUE, value); |
| 193 |
rt2500usb_register_write_lock(rt2x00dev, PHY_CSR9, reg); |
| 194 |
|
| 195 |
reg = 0; |
| 196 |
rt2x00_set_field16(®, PHY_CSR10_RF_VALUE, value >> 16); |
| 197 |
rt2x00_set_field16(®, PHY_CSR10_RF_NUMBER_OF_BITS, 20); |
| 198 |
rt2x00_set_field16(®, PHY_CSR10_RF_IF_SELECT, 0); |
| 199 |
rt2x00_set_field16(®, PHY_CSR10_RF_BUSY, 1); |
| 200 |
|
| 201 |
rt2500usb_register_write_lock(rt2x00dev, PHY_CSR10, reg); |
| 202 |
rt2x00_rf_write(rt2x00dev, word, value); |
| 203 |
} |
| 204 |
|
| 205 |
mutex_unlock(&rt2x00dev->csr_mutex); |
| 206 |
} |
| 207 |
|
| 208 |
#ifdef CONFIG_RT2X00_LIB_DEBUGFS |
| 209 |
static u32 _rt2500usb_register_read(struct rt2x00_dev *rt2x00dev, |
| 210 |
const unsigned int offset) |
| 211 |
{ |
| 212 |
return rt2500usb_register_read(rt2x00dev, offset); |
| 213 |
} |
| 214 |
|
| 215 |
static void _rt2500usb_register_write(struct rt2x00_dev *rt2x00dev, |
| 216 |
const unsigned int offset, |
| 217 |
u32 value) |
| 218 |
{ |
| 219 |
rt2500usb_register_write(rt2x00dev, offset, value); |
| 220 |
} |
| 221 |
|
| 222 |
static const struct rt2x00debug rt2500usb_rt2x00debug = { |
| 223 |
.owner = THIS_MODULE, |
| 224 |
.csr = { |
| 225 |
.read = _rt2500usb_register_read, |
| 226 |
.write = _rt2500usb_register_write, |
| 227 |
.flags = RT2X00DEBUGFS_OFFSET, |
| 228 |
.word_base = CSR_REG_BASE, |
| 229 |
.word_size = sizeof(u16), |
| 230 |
.word_count = CSR_REG_SIZE / sizeof(u16), |
| 231 |
}, |
| 232 |
.eeprom = { |
| 233 |
.read = rt2x00_eeprom_read, |
| 234 |
.write = rt2x00_eeprom_write, |
| 235 |
.word_base = EEPROM_BASE, |
| 236 |
.word_size = sizeof(u16), |
| 237 |
.word_count = EEPROM_SIZE / sizeof(u16), |
| 238 |
}, |
| 239 |
.bbp = { |
| 240 |
.read = rt2500usb_bbp_read, |
| 241 |
.write = rt2500usb_bbp_write, |
| 242 |
.word_base = BBP_BASE, |
| 243 |
.word_size = sizeof(u8), |
| 244 |
.word_count = BBP_SIZE / sizeof(u8), |
| 245 |
}, |
| 246 |
.rf = { |
| 247 |
.read = rt2x00_rf_read, |
| 248 |
.write = rt2500usb_rf_write, |
| 249 |
.word_base = RF_BASE, |
| 250 |
.word_size = sizeof(u32), |
| 251 |
.word_count = RF_SIZE / sizeof(u32), |
| 252 |
}, |
| 253 |
}; |
| 254 |
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ |
| 255 |
|
| 256 |
static int rt2500usb_rfkill_poll(struct rt2x00_dev *rt2x00dev) |
| 257 |
{ |
| 258 |
u16 reg; |
| 259 |
|
| 260 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR19); |
| 261 |
return rt2x00_get_field16(reg, MAC_CSR19_VAL7); |
| 262 |
} |
| 263 |
|
| 264 |
#ifdef CONFIG_RT2X00_LIB_LEDS |
| 265 |
static void rt2500usb_brightness_set(struct led_classdev *led_cdev, |
| 266 |
enum led_brightness brightness) |
| 267 |
{ |
| 268 |
struct rt2x00_led *led = |
| 269 |
container_of(led_cdev, struct rt2x00_led, led_dev); |
| 270 |
unsigned int enabled = brightness != LED_OFF; |
| 271 |
u16 reg; |
| 272 |
|
| 273 |
reg = rt2500usb_register_read(led->rt2x00dev, MAC_CSR20); |
| 274 |
|
| 275 |
if (led->type == LED_TYPE_RADIO || led->type == LED_TYPE_ASSOC) |
| 276 |
rt2x00_set_field16(®, MAC_CSR20_LINK, enabled); |
| 277 |
else if (led->type == LED_TYPE_ACTIVITY) |
| 278 |
rt2x00_set_field16(®, MAC_CSR20_ACTIVITY, enabled); |
| 279 |
|
| 280 |
rt2500usb_register_write(led->rt2x00dev, MAC_CSR20, reg); |
| 281 |
} |
| 282 |
|
| 283 |
static int rt2500usb_blink_set(struct led_classdev *led_cdev, |
| 284 |
unsigned long *delay_on, |
| 285 |
unsigned long *delay_off) |
| 286 |
{ |
| 287 |
struct rt2x00_led *led = |
| 288 |
container_of(led_cdev, struct rt2x00_led, led_dev); |
| 289 |
u16 reg; |
| 290 |
|
| 291 |
reg = rt2500usb_register_read(led->rt2x00dev, MAC_CSR21); |
| 292 |
rt2x00_set_field16(®, MAC_CSR21_ON_PERIOD, *delay_on); |
| 293 |
rt2x00_set_field16(®, MAC_CSR21_OFF_PERIOD, *delay_off); |
| 294 |
rt2500usb_register_write(led->rt2x00dev, MAC_CSR21, reg); |
| 295 |
|
| 296 |
return 0; |
| 297 |
} |
| 298 |
|
| 299 |
static void rt2500usb_init_led(struct rt2x00_dev *rt2x00dev, |
| 300 |
struct rt2x00_led *led, |
| 301 |
enum led_type type) |
| 302 |
{ |
| 303 |
led->rt2x00dev = rt2x00dev; |
| 304 |
led->type = type; |
| 305 |
led->led_dev.brightness_set = rt2500usb_brightness_set; |
| 306 |
led->led_dev.blink_set = rt2500usb_blink_set; |
| 307 |
led->flags = LED_INITIALIZED; |
| 308 |
} |
| 309 |
#endif /* CONFIG_RT2X00_LIB_LEDS */ |
| 310 |
|
| 311 |
/* |
| 312 |
* Configuration handlers. |
| 313 |
*/ |
| 314 |
|
| 315 |
/* |
| 316 |
* rt2500usb does not differentiate between shared and pairwise |
| 317 |
* keys, so we should use the same function for both key types. |
| 318 |
*/ |
| 319 |
static int rt2500usb_config_key(struct rt2x00_dev *rt2x00dev, |
| 320 |
struct rt2x00lib_crypto *crypto, |
| 321 |
struct ieee80211_key_conf *key) |
| 322 |
{ |
| 323 |
u32 mask; |
| 324 |
u16 reg; |
| 325 |
enum cipher curr_cipher; |
| 326 |
|
| 327 |
if (crypto->cmd == SET_KEY) { |
| 328 |
/* |
| 329 |
* Disallow to set WEP key other than with index 0, |
| 330 |
* it is known that not work at least on some hardware. |
| 331 |
* SW crypto will be used in that case. |
| 332 |
*/ |
| 333 |
if ((key->cipher == WLAN_CIPHER_SUITE_WEP40 || |
| 334 |
key->cipher == WLAN_CIPHER_SUITE_WEP104) && |
| 335 |
key->keyidx != 0) |
| 336 |
return -EOPNOTSUPP; |
| 337 |
|
| 338 |
/* |
| 339 |
* Pairwise key will always be entry 0, but this |
| 340 |
* could collide with a shared key on the same |
| 341 |
* position... |
| 342 |
*/ |
| 343 |
mask = TXRX_CSR0_KEY_ID.bit_mask; |
| 344 |
|
| 345 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0); |
| 346 |
curr_cipher = rt2x00_get_field16(reg, TXRX_CSR0_ALGORITHM); |
| 347 |
reg &= mask; |
| 348 |
|
| 349 |
if (reg && reg == mask) |
| 350 |
return -ENOSPC; |
| 351 |
|
| 352 |
reg = rt2x00_get_field16(reg, TXRX_CSR0_KEY_ID); |
| 353 |
|
| 354 |
key->hw_key_idx += reg ? ffz(reg) : 0; |
| 355 |
/* |
| 356 |
* Hardware requires that all keys use the same cipher |
| 357 |
* (e.g. TKIP-only, AES-only, but not TKIP+AES). |
| 358 |
* If this is not the first key, compare the cipher with the |
| 359 |
* first one and fall back to SW crypto if not the same. |
| 360 |
*/ |
| 361 |
if (key->hw_key_idx > 0 && crypto->cipher != curr_cipher) |
| 362 |
return -EOPNOTSUPP; |
| 363 |
|
| 364 |
rt2500usb_register_multiwrite(rt2x00dev, KEY_ENTRY(key->hw_key_idx), |
| 365 |
crypto->key, sizeof(crypto->key)); |
| 366 |
|
| 367 |
/* |
| 368 |
* The driver does not support the IV/EIV generation |
| 369 |
* in hardware. However it demands the data to be provided |
| 370 |
* both separately as well as inside the frame. |
| 371 |
* We already provided the CONFIG_CRYPTO_COPY_IV to rt2x00lib |
| 372 |
* to ensure rt2x00lib will not strip the data from the |
| 373 |
* frame after the copy, now we must tell mac80211 |
| 374 |
* to generate the IV/EIV data. |
| 375 |
*/ |
| 376 |
key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| 377 |
key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; |
| 378 |
} |
| 379 |
|
| 380 |
/* |
| 381 |
* TXRX_CSR0_KEY_ID contains only single-bit fields to indicate |
| 382 |
* a particular key is valid. |
| 383 |
*/ |
| 384 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0); |
| 385 |
rt2x00_set_field16(®, TXRX_CSR0_ALGORITHM, crypto->cipher); |
| 386 |
rt2x00_set_field16(®, TXRX_CSR0_IV_OFFSET, IEEE80211_HEADER); |
| 387 |
|
| 388 |
mask = rt2x00_get_field16(reg, TXRX_CSR0_KEY_ID); |
| 389 |
if (crypto->cmd == SET_KEY) |
| 390 |
mask |= 1 << key->hw_key_idx; |
| 391 |
else if (crypto->cmd == DISABLE_KEY) |
| 392 |
mask &= ~(1 << key->hw_key_idx); |
| 393 |
rt2x00_set_field16(®, TXRX_CSR0_KEY_ID, mask); |
| 394 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR0, reg); |
| 395 |
|
| 396 |
return 0; |
| 397 |
} |
| 398 |
|
| 399 |
static void rt2500usb_config_filter(struct rt2x00_dev *rt2x00dev, |
| 400 |
const unsigned int filter_flags) |
| 401 |
{ |
| 402 |
u16 reg; |
| 403 |
|
| 404 |
/* |
| 405 |
* Start configuration steps. |
| 406 |
* Note that the version error will always be dropped |
| 407 |
* and broadcast frames will always be accepted since |
| 408 |
* there is no filter for it at this time. |
| 409 |
*/ |
| 410 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2); |
| 411 |
rt2x00_set_field16(®, TXRX_CSR2_DROP_CRC, |
| 412 |
!(filter_flags & FIF_FCSFAIL)); |
| 413 |
rt2x00_set_field16(®, TXRX_CSR2_DROP_PHYSICAL, |
| 414 |
!(filter_flags & FIF_PLCPFAIL)); |
| 415 |
rt2x00_set_field16(®, TXRX_CSR2_DROP_CONTROL, |
| 416 |
!(filter_flags & FIF_CONTROL)); |
| 417 |
rt2x00_set_field16(®, TXRX_CSR2_DROP_NOT_TO_ME, |
| 418 |
!test_bit(CONFIG_MONITORING, &rt2x00dev->flags)); |
| 419 |
rt2x00_set_field16(®, TXRX_CSR2_DROP_TODS, |
| 420 |
!test_bit(CONFIG_MONITORING, &rt2x00dev->flags) && |
| 421 |
!rt2x00dev->intf_ap_count); |
| 422 |
rt2x00_set_field16(®, TXRX_CSR2_DROP_VERSION_ERROR, 1); |
| 423 |
rt2x00_set_field16(®, TXRX_CSR2_DROP_MULTICAST, |
| 424 |
!(filter_flags & FIF_ALLMULTI)); |
| 425 |
rt2x00_set_field16(®, TXRX_CSR2_DROP_BROADCAST, 0); |
| 426 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg); |
| 427 |
} |
| 428 |
|
| 429 |
static void rt2500usb_config_intf(struct rt2x00_dev *rt2x00dev, |
| 430 |
struct rt2x00_intf *intf, |
| 431 |
struct rt2x00intf_conf *conf, |
| 432 |
const unsigned int flags) |
| 433 |
{ |
| 434 |
unsigned int bcn_preload; |
| 435 |
u16 reg; |
| 436 |
|
| 437 |
if (flags & CONFIG_UPDATE_TYPE) { |
| 438 |
/* |
| 439 |
* Enable beacon config |
| 440 |
*/ |
| 441 |
bcn_preload = PREAMBLE + GET_DURATION(IEEE80211_HEADER, 20); |
| 442 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR20); |
| 443 |
rt2x00_set_field16(®, TXRX_CSR20_OFFSET, bcn_preload >> 6); |
| 444 |
rt2x00_set_field16(®, TXRX_CSR20_BCN_EXPECT_WINDOW, |
| 445 |
2 * (conf->type != NL80211_IFTYPE_STATION)); |
| 446 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR20, reg); |
| 447 |
|
| 448 |
/* |
| 449 |
* Enable synchronisation. |
| 450 |
*/ |
| 451 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR18); |
| 452 |
rt2x00_set_field16(®, TXRX_CSR18_OFFSET, 0); |
| 453 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR18, reg); |
| 454 |
|
| 455 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); |
| 456 |
rt2x00_set_field16(®, TXRX_CSR19_TSF_SYNC, conf->sync); |
| 457 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); |
| 458 |
} |
| 459 |
|
| 460 |
if (flags & CONFIG_UPDATE_MAC) |
| 461 |
rt2500usb_register_multiwrite(rt2x00dev, MAC_CSR2, conf->mac, |
| 462 |
(3 * sizeof(__le16))); |
| 463 |
|
| 464 |
if (flags & CONFIG_UPDATE_BSSID) |
| 465 |
rt2500usb_register_multiwrite(rt2x00dev, MAC_CSR5, conf->bssid, |
| 466 |
(3 * sizeof(__le16))); |
| 467 |
} |
| 468 |
|
| 469 |
static void rt2500usb_config_erp(struct rt2x00_dev *rt2x00dev, |
| 470 |
struct rt2x00lib_erp *erp, |
| 471 |
u32 changed) |
| 472 |
{ |
| 473 |
u16 reg; |
| 474 |
|
| 475 |
if (changed & BSS_CHANGED_ERP_PREAMBLE) { |
| 476 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR10); |
| 477 |
rt2x00_set_field16(®, TXRX_CSR10_AUTORESPOND_PREAMBLE, |
| 478 |
!!erp->short_preamble); |
| 479 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR10, reg); |
| 480 |
} |
| 481 |
|
| 482 |
if (changed & BSS_CHANGED_BASIC_RATES) |
| 483 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR11, |
| 484 |
erp->basic_rates); |
| 485 |
|
| 486 |
if (changed & BSS_CHANGED_BEACON_INT) { |
| 487 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR18); |
| 488 |
rt2x00_set_field16(®, TXRX_CSR18_INTERVAL, |
| 489 |
erp->beacon_int * 4); |
| 490 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR18, reg); |
| 491 |
} |
| 492 |
|
| 493 |
if (changed & BSS_CHANGED_ERP_SLOT) { |
| 494 |
rt2500usb_register_write(rt2x00dev, MAC_CSR10, erp->slot_time); |
| 495 |
rt2500usb_register_write(rt2x00dev, MAC_CSR11, erp->sifs); |
| 496 |
rt2500usb_register_write(rt2x00dev, MAC_CSR12, erp->eifs); |
| 497 |
} |
| 498 |
} |
| 499 |
|
| 500 |
static void rt2500usb_config_ant(struct rt2x00_dev *rt2x00dev, |
| 501 |
struct antenna_setup *ant) |
| 502 |
{ |
| 503 |
u8 r2; |
| 504 |
u8 r14; |
| 505 |
u16 csr5; |
| 506 |
u16 csr6; |
| 507 |
|
| 508 |
/* |
| 509 |
* We should never come here because rt2x00lib is supposed |
| 510 |
* to catch this and send us the correct antenna explicitely. |
| 511 |
*/ |
| 512 |
BUG_ON(ant->rx == ANTENNA_SW_DIVERSITY || |
| 513 |
ant->tx == ANTENNA_SW_DIVERSITY); |
| 514 |
|
| 515 |
r2 = rt2500usb_bbp_read(rt2x00dev, 2); |
| 516 |
r14 = rt2500usb_bbp_read(rt2x00dev, 14); |
| 517 |
csr5 = rt2500usb_register_read(rt2x00dev, PHY_CSR5); |
| 518 |
csr6 = rt2500usb_register_read(rt2x00dev, PHY_CSR6); |
| 519 |
|
| 520 |
/* |
| 521 |
* Configure the TX antenna. |
| 522 |
*/ |
| 523 |
switch (ant->tx) { |
| 524 |
case ANTENNA_HW_DIVERSITY: |
| 525 |
rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 1); |
| 526 |
rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 1); |
| 527 |
rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 1); |
| 528 |
break; |
| 529 |
case ANTENNA_A: |
| 530 |
rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 0); |
| 531 |
rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 0); |
| 532 |
rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 0); |
| 533 |
break; |
| 534 |
case ANTENNA_B: |
| 535 |
default: |
| 536 |
rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 2); |
| 537 |
rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 2); |
| 538 |
rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 2); |
| 539 |
break; |
| 540 |
} |
| 541 |
|
| 542 |
/* |
| 543 |
* Configure the RX antenna. |
| 544 |
*/ |
| 545 |
switch (ant->rx) { |
| 546 |
case ANTENNA_HW_DIVERSITY: |
| 547 |
rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 1); |
| 548 |
break; |
| 549 |
case ANTENNA_A: |
| 550 |
rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 0); |
| 551 |
break; |
| 552 |
case ANTENNA_B: |
| 553 |
default: |
| 554 |
rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 2); |
| 555 |
break; |
| 556 |
} |
| 557 |
|
| 558 |
/* |
| 559 |
* RT2525E and RT5222 need to flip TX I/Q |
| 560 |
*/ |
| 561 |
if (rt2x00_rf(rt2x00dev, RF2525E) || rt2x00_rf(rt2x00dev, RF5222)) { |
| 562 |
rt2x00_set_field8(&r2, BBP_R2_TX_IQ_FLIP, 1); |
| 563 |
rt2x00_set_field16(&csr5, PHY_CSR5_CCK_FLIP, 1); |
| 564 |
rt2x00_set_field16(&csr6, PHY_CSR6_OFDM_FLIP, 1); |
| 565 |
|
| 566 |
/* |
| 567 |
* RT2525E does not need RX I/Q Flip. |
| 568 |
*/ |
| 569 |
if (rt2x00_rf(rt2x00dev, RF2525E)) |
| 570 |
rt2x00_set_field8(&r14, BBP_R14_RX_IQ_FLIP, 0); |
| 571 |
} else { |
| 572 |
rt2x00_set_field16(&csr5, PHY_CSR5_CCK_FLIP, 0); |
| 573 |
rt2x00_set_field16(&csr6, PHY_CSR6_OFDM_FLIP, 0); |
| 574 |
} |
| 575 |
|
| 576 |
rt2500usb_bbp_write(rt2x00dev, 2, r2); |
| 577 |
rt2500usb_bbp_write(rt2x00dev, 14, r14); |
| 578 |
rt2500usb_register_write(rt2x00dev, PHY_CSR5, csr5); |
| 579 |
rt2500usb_register_write(rt2x00dev, PHY_CSR6, csr6); |
| 580 |
} |
| 581 |
|
| 582 |
static void rt2500usb_config_channel(struct rt2x00_dev *rt2x00dev, |
| 583 |
struct rf_channel *rf, const int txpower) |
| 584 |
{ |
| 585 |
/* |
| 586 |
* Set TXpower. |
| 587 |
*/ |
| 588 |
rt2x00_set_field32(&rf->rf3, RF3_TXPOWER, TXPOWER_TO_DEV(txpower)); |
| 589 |
|
| 590 |
/* |
| 591 |
* For RT2525E we should first set the channel to half band higher. |
| 592 |
*/ |
| 593 |
if (rt2x00_rf(rt2x00dev, RF2525E)) { |
| 594 |
static const u32 vals[] = { |
| 595 |
0x000008aa, 0x000008ae, 0x000008ae, 0x000008b2, |
| 596 |
0x000008b2, 0x000008b6, 0x000008b6, 0x000008ba, |
| 597 |
0x000008ba, 0x000008be, 0x000008b7, 0x00000902, |
| 598 |
0x00000902, 0x00000906 |
| 599 |
}; |
| 600 |
|
| 601 |
rt2500usb_rf_write(rt2x00dev, 2, vals[rf->channel - 1]); |
| 602 |
if (rf->rf4) |
| 603 |
rt2500usb_rf_write(rt2x00dev, 4, rf->rf4); |
| 604 |
} |
| 605 |
|
| 606 |
rt2500usb_rf_write(rt2x00dev, 1, rf->rf1); |
| 607 |
rt2500usb_rf_write(rt2x00dev, 2, rf->rf2); |
| 608 |
rt2500usb_rf_write(rt2x00dev, 3, rf->rf3); |
| 609 |
if (rf->rf4) |
| 610 |
rt2500usb_rf_write(rt2x00dev, 4, rf->rf4); |
| 611 |
} |
| 612 |
|
| 613 |
static void rt2500usb_config_txpower(struct rt2x00_dev *rt2x00dev, |
| 614 |
const int txpower) |
| 615 |
{ |
| 616 |
u32 rf3; |
| 617 |
|
| 618 |
rf3 = rt2x00_rf_read(rt2x00dev, 3); |
| 619 |
rt2x00_set_field32(&rf3, RF3_TXPOWER, TXPOWER_TO_DEV(txpower)); |
| 620 |
rt2500usb_rf_write(rt2x00dev, 3, rf3); |
| 621 |
} |
| 622 |
|
| 623 |
static void rt2500usb_config_ps(struct rt2x00_dev *rt2x00dev, |
| 624 |
struct rt2x00lib_conf *libconf) |
| 625 |
{ |
| 626 |
enum dev_state state = |
| 627 |
(libconf->conf->flags & IEEE80211_CONF_PS) ? |
| 628 |
STATE_SLEEP : STATE_AWAKE; |
| 629 |
u16 reg; |
| 630 |
|
| 631 |
if (state == STATE_SLEEP) { |
| 632 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18); |
| 633 |
rt2x00_set_field16(®, MAC_CSR18_DELAY_AFTER_BEACON, |
| 634 |
rt2x00dev->beacon_int - 20); |
| 635 |
rt2x00_set_field16(®, MAC_CSR18_BEACONS_BEFORE_WAKEUP, |
| 636 |
libconf->conf->listen_interval - 1); |
| 637 |
|
| 638 |
/* We must first disable autowake before it can be enabled */ |
| 639 |
rt2x00_set_field16(®, MAC_CSR18_AUTO_WAKE, 0); |
| 640 |
rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg); |
| 641 |
|
| 642 |
rt2x00_set_field16(®, MAC_CSR18_AUTO_WAKE, 1); |
| 643 |
rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg); |
| 644 |
} else { |
| 645 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18); |
| 646 |
rt2x00_set_field16(®, MAC_CSR18_AUTO_WAKE, 0); |
| 647 |
rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg); |
| 648 |
} |
| 649 |
|
| 650 |
rt2x00dev->ops->lib->set_device_state(rt2x00dev, state); |
| 651 |
} |
| 652 |
|
| 653 |
static void rt2500usb_config(struct rt2x00_dev *rt2x00dev, |
| 654 |
struct rt2x00lib_conf *libconf, |
| 655 |
const unsigned int flags) |
| 656 |
{ |
| 657 |
if (flags & IEEE80211_CONF_CHANGE_CHANNEL) |
| 658 |
rt2500usb_config_channel(rt2x00dev, &libconf->rf, |
| 659 |
libconf->conf->power_level); |
| 660 |
if ((flags & IEEE80211_CONF_CHANGE_POWER) && |
| 661 |
!(flags & IEEE80211_CONF_CHANGE_CHANNEL)) |
| 662 |
rt2500usb_config_txpower(rt2x00dev, |
| 663 |
libconf->conf->power_level); |
| 664 |
if (flags & IEEE80211_CONF_CHANGE_PS) |
| 665 |
rt2500usb_config_ps(rt2x00dev, libconf); |
| 666 |
} |
| 667 |
|
| 668 |
/* |
| 669 |
* Link tuning |
| 670 |
*/ |
| 671 |
static void rt2500usb_link_stats(struct rt2x00_dev *rt2x00dev, |
| 672 |
struct link_qual *qual) |
| 673 |
{ |
| 674 |
u16 reg; |
| 675 |
|
| 676 |
/* |
| 677 |
* Update FCS error count from register. |
| 678 |
*/ |
| 679 |
reg = rt2500usb_register_read(rt2x00dev, STA_CSR0); |
| 680 |
qual->rx_failed = rt2x00_get_field16(reg, STA_CSR0_FCS_ERROR); |
| 681 |
|
| 682 |
/* |
| 683 |
* Update False CCA count from register. |
| 684 |
*/ |
| 685 |
reg = rt2500usb_register_read(rt2x00dev, STA_CSR3); |
| 686 |
qual->false_cca = rt2x00_get_field16(reg, STA_CSR3_FALSE_CCA_ERROR); |
| 687 |
} |
| 688 |
|
| 689 |
static void rt2500usb_reset_tuner(struct rt2x00_dev *rt2x00dev, |
| 690 |
struct link_qual *qual) |
| 691 |
{ |
| 692 |
u16 eeprom; |
| 693 |
u16 value; |
| 694 |
|
| 695 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R24); |
| 696 |
value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R24_LOW); |
| 697 |
rt2500usb_bbp_write(rt2x00dev, 24, value); |
| 698 |
|
| 699 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R25); |
| 700 |
value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R25_LOW); |
| 701 |
rt2500usb_bbp_write(rt2x00dev, 25, value); |
| 702 |
|
| 703 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R61); |
| 704 |
value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R61_LOW); |
| 705 |
rt2500usb_bbp_write(rt2x00dev, 61, value); |
| 706 |
|
| 707 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_VGC); |
| 708 |
value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_VGCUPPER); |
| 709 |
rt2500usb_bbp_write(rt2x00dev, 17, value); |
| 710 |
|
| 711 |
qual->vgc_level = value; |
| 712 |
} |
| 713 |
|
| 714 |
/* |
| 715 |
* Queue handlers. |
| 716 |
*/ |
| 717 |
static void rt2500usb_start_queue(struct data_queue *queue) |
| 718 |
{ |
| 719 |
struct rt2x00_dev *rt2x00dev = queue->rt2x00dev; |
| 720 |
u16 reg; |
| 721 |
|
| 722 |
switch (queue->qid) { |
| 723 |
case QID_RX: |
| 724 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2); |
| 725 |
rt2x00_set_field16(®, TXRX_CSR2_DISABLE_RX, 0); |
| 726 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg); |
| 727 |
break; |
| 728 |
case QID_BEACON: |
| 729 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); |
| 730 |
rt2x00_set_field16(®, TXRX_CSR19_TSF_COUNT, 1); |
| 731 |
rt2x00_set_field16(®, TXRX_CSR19_TBCN, 1); |
| 732 |
rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 1); |
| 733 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); |
| 734 |
break; |
| 735 |
default: |
| 736 |
break; |
| 737 |
} |
| 738 |
} |
| 739 |
|
| 740 |
static void rt2500usb_stop_queue(struct data_queue *queue) |
| 741 |
{ |
| 742 |
struct rt2x00_dev *rt2x00dev = queue->rt2x00dev; |
| 743 |
u16 reg; |
| 744 |
|
| 745 |
switch (queue->qid) { |
| 746 |
case QID_RX: |
| 747 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2); |
| 748 |
rt2x00_set_field16(®, TXRX_CSR2_DISABLE_RX, 1); |
| 749 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg); |
| 750 |
break; |
| 751 |
case QID_BEACON: |
| 752 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); |
| 753 |
rt2x00_set_field16(®, TXRX_CSR19_TSF_COUNT, 0); |
| 754 |
rt2x00_set_field16(®, TXRX_CSR19_TBCN, 0); |
| 755 |
rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 0); |
| 756 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); |
| 757 |
break; |
| 758 |
default: |
| 759 |
break; |
| 760 |
} |
| 761 |
} |
| 762 |
|
| 763 |
/* |
| 764 |
* Initialization functions. |
| 765 |
*/ |
| 766 |
static int rt2500usb_init_registers(struct rt2x00_dev *rt2x00dev) |
| 767 |
{ |
| 768 |
u16 reg; |
| 769 |
|
| 770 |
rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0x0001, |
| 771 |
USB_MODE_TEST, REGISTER_TIMEOUT); |
| 772 |
rt2x00usb_vendor_request_sw(rt2x00dev, USB_SINGLE_WRITE, 0x0308, |
| 773 |
0x00f0, REGISTER_TIMEOUT); |
| 774 |
|
| 775 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2); |
| 776 |
rt2x00_set_field16(®, TXRX_CSR2_DISABLE_RX, 1); |
| 777 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg); |
| 778 |
|
| 779 |
rt2500usb_register_write(rt2x00dev, MAC_CSR13, 0x1111); |
| 780 |
rt2500usb_register_write(rt2x00dev, MAC_CSR14, 0x1e11); |
| 781 |
|
| 782 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1); |
| 783 |
rt2x00_set_field16(®, MAC_CSR1_SOFT_RESET, 1); |
| 784 |
rt2x00_set_field16(®, MAC_CSR1_BBP_RESET, 1); |
| 785 |
rt2x00_set_field16(®, MAC_CSR1_HOST_READY, 0); |
| 786 |
rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg); |
| 787 |
|
| 788 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1); |
| 789 |
rt2x00_set_field16(®, MAC_CSR1_SOFT_RESET, 0); |
| 790 |
rt2x00_set_field16(®, MAC_CSR1_BBP_RESET, 0); |
| 791 |
rt2x00_set_field16(®, MAC_CSR1_HOST_READY, 0); |
| 792 |
rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg); |
| 793 |
|
| 794 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR5); |
| 795 |
rt2x00_set_field16(®, TXRX_CSR5_BBP_ID0, 13); |
| 796 |
rt2x00_set_field16(®, TXRX_CSR5_BBP_ID0_VALID, 1); |
| 797 |
rt2x00_set_field16(®, TXRX_CSR5_BBP_ID1, 12); |
| 798 |
rt2x00_set_field16(®, TXRX_CSR5_BBP_ID1_VALID, 1); |
| 799 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR5, reg); |
| 800 |
|
| 801 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR6); |
| 802 |
rt2x00_set_field16(®, TXRX_CSR6_BBP_ID0, 10); |
| 803 |
rt2x00_set_field16(®, TXRX_CSR6_BBP_ID0_VALID, 1); |
| 804 |
rt2x00_set_field16(®, TXRX_CSR6_BBP_ID1, 11); |
| 805 |
rt2x00_set_field16(®, TXRX_CSR6_BBP_ID1_VALID, 1); |
| 806 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR6, reg); |
| 807 |
|
| 808 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR7); |
| 809 |
rt2x00_set_field16(®, TXRX_CSR7_BBP_ID0, 7); |
| 810 |
rt2x00_set_field16(®, TXRX_CSR7_BBP_ID0_VALID, 1); |
| 811 |
rt2x00_set_field16(®, TXRX_CSR7_BBP_ID1, 6); |
| 812 |
rt2x00_set_field16(®, TXRX_CSR7_BBP_ID1_VALID, 1); |
| 813 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR7, reg); |
| 814 |
|
| 815 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR8); |
| 816 |
rt2x00_set_field16(®, TXRX_CSR8_BBP_ID0, 5); |
| 817 |
rt2x00_set_field16(®, TXRX_CSR8_BBP_ID0_VALID, 1); |
| 818 |
rt2x00_set_field16(®, TXRX_CSR8_BBP_ID1, 0); |
| 819 |
rt2x00_set_field16(®, TXRX_CSR8_BBP_ID1_VALID, 0); |
| 820 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR8, reg); |
| 821 |
|
| 822 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); |
| 823 |
rt2x00_set_field16(®, TXRX_CSR19_TSF_COUNT, 0); |
| 824 |
rt2x00_set_field16(®, TXRX_CSR19_TSF_SYNC, 0); |
| 825 |
rt2x00_set_field16(®, TXRX_CSR19_TBCN, 0); |
| 826 |
rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 0); |
| 827 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); |
| 828 |
|
| 829 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR21, 0xe78f); |
| 830 |
rt2500usb_register_write(rt2x00dev, MAC_CSR9, 0xff1d); |
| 831 |
|
| 832 |
if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_AWAKE)) |
| 833 |
return -EBUSY; |
| 834 |
|
| 835 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1); |
| 836 |
rt2x00_set_field16(®, MAC_CSR1_SOFT_RESET, 0); |
| 837 |
rt2x00_set_field16(®, MAC_CSR1_BBP_RESET, 0); |
| 838 |
rt2x00_set_field16(®, MAC_CSR1_HOST_READY, 1); |
| 839 |
rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg); |
| 840 |
|
| 841 |
if (rt2x00_rev(rt2x00dev) >= RT2570_VERSION_C) { |
| 842 |
reg = rt2500usb_register_read(rt2x00dev, PHY_CSR2); |
| 843 |
rt2x00_set_field16(®, PHY_CSR2_LNA, 0); |
| 844 |
} else { |
| 845 |
reg = 0; |
| 846 |
rt2x00_set_field16(®, PHY_CSR2_LNA, 1); |
| 847 |
rt2x00_set_field16(®, PHY_CSR2_LNA_MODE, 3); |
| 848 |
} |
| 849 |
rt2500usb_register_write(rt2x00dev, PHY_CSR2, reg); |
| 850 |
|
| 851 |
rt2500usb_register_write(rt2x00dev, MAC_CSR11, 0x0002); |
| 852 |
rt2500usb_register_write(rt2x00dev, MAC_CSR22, 0x0053); |
| 853 |
rt2500usb_register_write(rt2x00dev, MAC_CSR15, 0x01ee); |
| 854 |
rt2500usb_register_write(rt2x00dev, MAC_CSR16, 0x0000); |
| 855 |
|
| 856 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR8); |
| 857 |
rt2x00_set_field16(®, MAC_CSR8_MAX_FRAME_UNIT, |
| 858 |
rt2x00dev->rx->data_size); |
| 859 |
rt2500usb_register_write(rt2x00dev, MAC_CSR8, reg); |
| 860 |
|
| 861 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0); |
| 862 |
rt2x00_set_field16(®, TXRX_CSR0_ALGORITHM, CIPHER_NONE); |
| 863 |
rt2x00_set_field16(®, TXRX_CSR0_IV_OFFSET, IEEE80211_HEADER); |
| 864 |
rt2x00_set_field16(®, TXRX_CSR0_KEY_ID, 0); |
| 865 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR0, reg); |
| 866 |
|
| 867 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18); |
| 868 |
rt2x00_set_field16(®, MAC_CSR18_DELAY_AFTER_BEACON, 90); |
| 869 |
rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg); |
| 870 |
|
| 871 |
reg = rt2500usb_register_read(rt2x00dev, PHY_CSR4); |
| 872 |
rt2x00_set_field16(®, PHY_CSR4_LOW_RF_LE, 1); |
| 873 |
rt2500usb_register_write(rt2x00dev, PHY_CSR4, reg); |
| 874 |
|
| 875 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR1); |
| 876 |
rt2x00_set_field16(®, TXRX_CSR1_AUTO_SEQUENCE, 1); |
| 877 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR1, reg); |
| 878 |
|
| 879 |
return 0; |
| 880 |
} |
| 881 |
|
| 882 |
static int rt2500usb_wait_bbp_ready(struct rt2x00_dev *rt2x00dev) |
| 883 |
{ |
| 884 |
unsigned int i; |
| 885 |
u8 value; |
| 886 |
|
| 887 |
for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) { |
| 888 |
value = rt2500usb_bbp_read(rt2x00dev, 0); |
| 889 |
if ((value != 0xff) && (value != 0x00)) |
| 890 |
return 0; |
| 891 |
udelay(REGISTER_BUSY_DELAY); |
| 892 |
} |
| 893 |
|
| 894 |
rt2x00_err(rt2x00dev, "BBP register access failed, aborting\n"); |
| 895 |
return -EACCES; |
| 896 |
} |
| 897 |
|
| 898 |
static int rt2500usb_init_bbp(struct rt2x00_dev *rt2x00dev) |
| 899 |
{ |
| 900 |
unsigned int i; |
| 901 |
u16 eeprom; |
| 902 |
u8 value; |
| 903 |
u8 reg_id; |
| 904 |
|
| 905 |
if (unlikely(rt2500usb_wait_bbp_ready(rt2x00dev))) |
| 906 |
return -EACCES; |
| 907 |
|
| 908 |
rt2500usb_bbp_write(rt2x00dev, 3, 0x02); |
| 909 |
rt2500usb_bbp_write(rt2x00dev, 4, 0x19); |
| 910 |
rt2500usb_bbp_write(rt2x00dev, 14, 0x1c); |
| 911 |
rt2500usb_bbp_write(rt2x00dev, 15, 0x30); |
| 912 |
rt2500usb_bbp_write(rt2x00dev, 16, 0xac); |
| 913 |
rt2500usb_bbp_write(rt2x00dev, 18, 0x18); |
| 914 |
rt2500usb_bbp_write(rt2x00dev, 19, 0xff); |
| 915 |
rt2500usb_bbp_write(rt2x00dev, 20, 0x1e); |
| 916 |
rt2500usb_bbp_write(rt2x00dev, 21, 0x08); |
| 917 |
rt2500usb_bbp_write(rt2x00dev, 22, 0x08); |
| 918 |
rt2500usb_bbp_write(rt2x00dev, 23, 0x08); |
| 919 |
rt2500usb_bbp_write(rt2x00dev, 24, 0x80); |
| 920 |
rt2500usb_bbp_write(rt2x00dev, 25, 0x50); |
| 921 |
rt2500usb_bbp_write(rt2x00dev, 26, 0x08); |
| 922 |
rt2500usb_bbp_write(rt2x00dev, 27, 0x23); |
| 923 |
rt2500usb_bbp_write(rt2x00dev, 30, 0x10); |
| 924 |
rt2500usb_bbp_write(rt2x00dev, 31, 0x2b); |
| 925 |
rt2500usb_bbp_write(rt2x00dev, 32, 0xb9); |
| 926 |
rt2500usb_bbp_write(rt2x00dev, 34, 0x12); |
| 927 |
rt2500usb_bbp_write(rt2x00dev, 35, 0x50); |
| 928 |
rt2500usb_bbp_write(rt2x00dev, 39, 0xc4); |
| 929 |
rt2500usb_bbp_write(rt2x00dev, 40, 0x02); |
| 930 |
rt2500usb_bbp_write(rt2x00dev, 41, 0x60); |
| 931 |
rt2500usb_bbp_write(rt2x00dev, 53, 0x10); |
| 932 |
rt2500usb_bbp_write(rt2x00dev, 54, 0x18); |
| 933 |
rt2500usb_bbp_write(rt2x00dev, 56, 0x08); |
| 934 |
rt2500usb_bbp_write(rt2x00dev, 57, 0x10); |
| 935 |
rt2500usb_bbp_write(rt2x00dev, 58, 0x08); |
| 936 |
rt2500usb_bbp_write(rt2x00dev, 61, 0x60); |
| 937 |
rt2500usb_bbp_write(rt2x00dev, 62, 0x10); |
| 938 |
rt2500usb_bbp_write(rt2x00dev, 75, 0xff); |
| 939 |
|
| 940 |
for (i = 0; i < EEPROM_BBP_SIZE; i++) { |
| 941 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i); |
| 942 |
|
| 943 |
if (eeprom != 0xffff && eeprom != 0x0000) { |
| 944 |
reg_id = rt2x00_get_field16(eeprom, EEPROM_BBP_REG_ID); |
| 945 |
value = rt2x00_get_field16(eeprom, EEPROM_BBP_VALUE); |
| 946 |
rt2500usb_bbp_write(rt2x00dev, reg_id, value); |
| 947 |
} |
| 948 |
} |
| 949 |
|
| 950 |
return 0; |
| 951 |
} |
| 952 |
|
| 953 |
/* |
| 954 |
* Device state switch handlers. |
| 955 |
*/ |
| 956 |
static int rt2500usb_enable_radio(struct rt2x00_dev *rt2x00dev) |
| 957 |
{ |
| 958 |
/* |
| 959 |
* Initialize all registers. |
| 960 |
*/ |
| 961 |
if (unlikely(rt2500usb_init_registers(rt2x00dev) || |
| 962 |
rt2500usb_init_bbp(rt2x00dev))) |
| 963 |
return -EIO; |
| 964 |
|
| 965 |
return 0; |
| 966 |
} |
| 967 |
|
| 968 |
static void rt2500usb_disable_radio(struct rt2x00_dev *rt2x00dev) |
| 969 |
{ |
| 970 |
rt2500usb_register_write(rt2x00dev, MAC_CSR13, 0x2121); |
| 971 |
rt2500usb_register_write(rt2x00dev, MAC_CSR14, 0x2121); |
| 972 |
|
| 973 |
/* |
| 974 |
* Disable synchronisation. |
| 975 |
*/ |
| 976 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, 0); |
| 977 |
|
| 978 |
rt2x00usb_disable_radio(rt2x00dev); |
| 979 |
} |
| 980 |
|
| 981 |
static int rt2500usb_set_state(struct rt2x00_dev *rt2x00dev, |
| 982 |
enum dev_state state) |
| 983 |
{ |
| 984 |
u16 reg; |
| 985 |
u16 reg2; |
| 986 |
unsigned int i; |
| 987 |
bool put_to_sleep; |
| 988 |
u8 bbp_state; |
| 989 |
u8 rf_state; |
| 990 |
|
| 991 |
put_to_sleep = (state != STATE_AWAKE); |
| 992 |
|
| 993 |
reg = 0; |
| 994 |
rt2x00_set_field16(®, MAC_CSR17_BBP_DESIRE_STATE, state); |
| 995 |
rt2x00_set_field16(®, MAC_CSR17_RF_DESIRE_STATE, state); |
| 996 |
rt2x00_set_field16(®, MAC_CSR17_PUT_TO_SLEEP, put_to_sleep); |
| 997 |
rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg); |
| 998 |
rt2x00_set_field16(®, MAC_CSR17_SET_STATE, 1); |
| 999 |
rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg); |
| 1000 |
|
| 1001 |
/* |
| 1002 |
* Device is not guaranteed to be in the requested state yet. |
| 1003 |
* We must wait until the register indicates that the |
| 1004 |
* device has entered the correct state. |
| 1005 |
*/ |
| 1006 |
for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) { |
| 1007 |
reg2 = rt2500usb_register_read(rt2x00dev, MAC_CSR17); |
| 1008 |
bbp_state = rt2x00_get_field16(reg2, MAC_CSR17_BBP_CURR_STATE); |
| 1009 |
rf_state = rt2x00_get_field16(reg2, MAC_CSR17_RF_CURR_STATE); |
| 1010 |
if (bbp_state == state && rf_state == state) |
| 1011 |
return 0; |
| 1012 |
rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg); |
| 1013 |
msleep(30); |
| 1014 |
} |
| 1015 |
|
| 1016 |
return -EBUSY; |
| 1017 |
} |
| 1018 |
|
| 1019 |
static int rt2500usb_set_device_state(struct rt2x00_dev *rt2x00dev, |
| 1020 |
enum dev_state state) |
| 1021 |
{ |
| 1022 |
int retval = 0; |
| 1023 |
|
| 1024 |
switch (state) { |
| 1025 |
case STATE_RADIO_ON: |
| 1026 |
retval = rt2500usb_enable_radio(rt2x00dev); |
| 1027 |
break; |
| 1028 |
case STATE_RADIO_OFF: |
| 1029 |
rt2500usb_disable_radio(rt2x00dev); |
| 1030 |
break; |
| 1031 |
case STATE_RADIO_IRQ_ON: |
| 1032 |
case STATE_RADIO_IRQ_OFF: |
| 1033 |
/* No support, but no error either */ |
| 1034 |
break; |
| 1035 |
case STATE_DEEP_SLEEP: |
| 1036 |
case STATE_SLEEP: |
| 1037 |
case STATE_STANDBY: |
| 1038 |
case STATE_AWAKE: |
| 1039 |
retval = rt2500usb_set_state(rt2x00dev, state); |
| 1040 |
break; |
| 1041 |
default: |
| 1042 |
retval = -ENOTSUPP; |
| 1043 |
break; |
| 1044 |
} |
| 1045 |
|
| 1046 |
if (unlikely(retval)) |
| 1047 |
rt2x00_err(rt2x00dev, "Device failed to enter state %d (%d)\n", |
| 1048 |
state, retval); |
| 1049 |
|
| 1050 |
return retval; |
| 1051 |
} |
| 1052 |
|
| 1053 |
/* |
| 1054 |
* TX descriptor initialization |
| 1055 |
*/ |
| 1056 |
static void rt2500usb_write_tx_desc(struct queue_entry *entry, |
| 1057 |
struct txentry_desc *txdesc) |
| 1058 |
{ |
| 1059 |
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); |
| 1060 |
__le32 *txd = (__le32 *) entry->skb->data; |
| 1061 |
u32 word; |
| 1062 |
|
| 1063 |
/* |
| 1064 |
* Start writing the descriptor words. |
| 1065 |
*/ |
| 1066 |
word = rt2x00_desc_read(txd, 0); |
| 1067 |
rt2x00_set_field32(&word, TXD_W0_RETRY_LIMIT, txdesc->retry_limit); |
| 1068 |
rt2x00_set_field32(&word, TXD_W0_MORE_FRAG, |
| 1069 |
test_bit(ENTRY_TXD_MORE_FRAG, &txdesc->flags)); |
| 1070 |
rt2x00_set_field32(&word, TXD_W0_ACK, |
| 1071 |
test_bit(ENTRY_TXD_ACK, &txdesc->flags)); |
| 1072 |
rt2x00_set_field32(&word, TXD_W0_TIMESTAMP, |
| 1073 |
test_bit(ENTRY_TXD_REQ_TIMESTAMP, &txdesc->flags)); |
| 1074 |
rt2x00_set_field32(&word, TXD_W0_OFDM, |
| 1075 |
(txdesc->rate_mode == RATE_MODE_OFDM)); |
| 1076 |
rt2x00_set_field32(&word, TXD_W0_NEW_SEQ, |
| 1077 |
test_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags)); |
| 1078 |
rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->u.plcp.ifs); |
| 1079 |
rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, txdesc->length); |
| 1080 |
rt2x00_set_field32(&word, TXD_W0_CIPHER, !!txdesc->cipher); |
| 1081 |
rt2x00_set_field32(&word, TXD_W0_KEY_ID, txdesc->key_idx); |
| 1082 |
rt2x00_desc_write(txd, 0, word); |
| 1083 |
|
| 1084 |
word = rt2x00_desc_read(txd, 1); |
| 1085 |
rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, txdesc->iv_offset); |
| 1086 |
rt2x00_set_field32(&word, TXD_W1_AIFS, entry->queue->aifs); |
| 1087 |
rt2x00_set_field32(&word, TXD_W1_CWMIN, entry->queue->cw_min); |
| 1088 |
rt2x00_set_field32(&word, TXD_W1_CWMAX, entry->queue->cw_max); |
| 1089 |
rt2x00_desc_write(txd, 1, word); |
| 1090 |
|
| 1091 |
word = rt2x00_desc_read(txd, 2); |
| 1092 |
rt2x00_set_field32(&word, TXD_W2_PLCP_SIGNAL, txdesc->u.plcp.signal); |
| 1093 |
rt2x00_set_field32(&word, TXD_W2_PLCP_SERVICE, txdesc->u.plcp.service); |
| 1094 |
rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_LOW, |
| 1095 |
txdesc->u.plcp.length_low); |
| 1096 |
rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_HIGH, |
| 1097 |
txdesc->u.plcp.length_high); |
| 1098 |
rt2x00_desc_write(txd, 2, word); |
| 1099 |
|
| 1100 |
if (test_bit(ENTRY_TXD_ENCRYPT, &txdesc->flags)) { |
| 1101 |
_rt2x00_desc_write(txd, 3, skbdesc->iv[0]); |
| 1102 |
_rt2x00_desc_write(txd, 4, skbdesc->iv[1]); |
| 1103 |
} |
| 1104 |
|
| 1105 |
/* |
| 1106 |
* Register descriptor details in skb frame descriptor. |
| 1107 |
*/ |
| 1108 |
skbdesc->flags |= SKBDESC_DESC_IN_SKB; |
| 1109 |
skbdesc->desc = txd; |
| 1110 |
skbdesc->desc_len = TXD_DESC_SIZE; |
| 1111 |
} |
| 1112 |
|
| 1113 |
/* |
| 1114 |
* TX data initialization |
| 1115 |
*/ |
| 1116 |
static void rt2500usb_beacondone(struct urb *urb); |
| 1117 |
|
| 1118 |
static void rt2500usb_write_beacon(struct queue_entry *entry, |
| 1119 |
struct txentry_desc *txdesc) |
| 1120 |
{ |
| 1121 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 1122 |
struct usb_device *usb_dev = to_usb_device_intf(rt2x00dev->dev); |
| 1123 |
struct queue_entry_priv_usb_bcn *bcn_priv = entry->priv_data; |
| 1124 |
int pipe = usb_sndbulkpipe(usb_dev, entry->queue->usb_endpoint); |
| 1125 |
int length; |
| 1126 |
u16 reg, reg0; |
| 1127 |
|
| 1128 |
/* |
| 1129 |
* Disable beaconing while we are reloading the beacon data, |
| 1130 |
* otherwise we might be sending out invalid data. |
| 1131 |
*/ |
| 1132 |
reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); |
| 1133 |
rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 0); |
| 1134 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); |
| 1135 |
|
| 1136 |
/* |
| 1137 |
* Add space for the descriptor in front of the skb. |
| 1138 |
*/ |
| 1139 |
skb_push(entry->skb, TXD_DESC_SIZE); |
| 1140 |
memset(entry->skb->data, 0, TXD_DESC_SIZE); |
| 1141 |
|
| 1142 |
/* |
| 1143 |
* Write the TX descriptor for the beacon. |
| 1144 |
*/ |
| 1145 |
rt2500usb_write_tx_desc(entry, txdesc); |
| 1146 |
|
| 1147 |
/* |
| 1148 |
* Dump beacon to userspace through debugfs. |
| 1149 |
*/ |
| 1150 |
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_BEACON, entry); |
| 1151 |
|
| 1152 |
/* |
| 1153 |
* USB devices cannot blindly pass the skb->len as the |
| 1154 |
* length of the data to usb_fill_bulk_urb. Pass the skb |
| 1155 |
* to the driver to determine what the length should be. |
| 1156 |
*/ |
| 1157 |
length = rt2x00dev->ops->lib->get_tx_data_len(entry); |
| 1158 |
|
| 1159 |
usb_fill_bulk_urb(bcn_priv->urb, usb_dev, pipe, |
| 1160 |
entry->skb->data, length, rt2500usb_beacondone, |
| 1161 |
entry); |
| 1162 |
|
| 1163 |
/* |
| 1164 |
* Second we need to create the guardian byte. |
| 1165 |
* We only need a single byte, so lets recycle |
| 1166 |
* the 'flags' field we are not using for beacons. |
| 1167 |
*/ |
| 1168 |
bcn_priv->guardian_data = 0; |
| 1169 |
usb_fill_bulk_urb(bcn_priv->guardian_urb, usb_dev, pipe, |
| 1170 |
&bcn_priv->guardian_data, 1, rt2500usb_beacondone, |
| 1171 |
entry); |
| 1172 |
|
| 1173 |
/* |
| 1174 |
* Send out the guardian byte. |
| 1175 |
*/ |
| 1176 |
usb_submit_urb(bcn_priv->guardian_urb, GFP_ATOMIC); |
| 1177 |
|
| 1178 |
/* |
| 1179 |
* Enable beaconing again. |
| 1180 |
*/ |
| 1181 |
rt2x00_set_field16(®, TXRX_CSR19_TSF_COUNT, 1); |
| 1182 |
rt2x00_set_field16(®, TXRX_CSR19_TBCN, 1); |
| 1183 |
reg0 = reg; |
| 1184 |
rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 1); |
| 1185 |
/* |
| 1186 |
* Beacon generation will fail initially. |
| 1187 |
* To prevent this we need to change the TXRX_CSR19 |
| 1188 |
* register several times (reg0 is the same as reg |
| 1189 |
* except for TXRX_CSR19_BEACON_GEN, which is 0 in reg0 |
| 1190 |
* and 1 in reg). |
| 1191 |
*/ |
| 1192 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); |
| 1193 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg0); |
| 1194 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); |
| 1195 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg0); |
| 1196 |
rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); |
| 1197 |
} |
| 1198 |
|
| 1199 |
static int rt2500usb_get_tx_data_len(struct queue_entry *entry) |
| 1200 |
{ |
| 1201 |
int length; |
| 1202 |
|
| 1203 |
/* |
| 1204 |
* The length _must_ be a multiple of 2, |
| 1205 |
* but it must _not_ be a multiple of the USB packet size. |
| 1206 |
*/ |
| 1207 |
length = roundup(entry->skb->len, 2); |
| 1208 |
length += (2 * !(length % entry->queue->usb_maxpacket)); |
| 1209 |
|
| 1210 |
return length; |
| 1211 |
} |
| 1212 |
|
| 1213 |
/* |
| 1214 |
* RX control handlers |
| 1215 |
*/ |
| 1216 |
static void rt2500usb_fill_rxdone(struct queue_entry *entry, |
| 1217 |
struct rxdone_entry_desc *rxdesc) |
| 1218 |
{ |
| 1219 |
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; |
| 1220 |
struct queue_entry_priv_usb *entry_priv = entry->priv_data; |
| 1221 |
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); |
| 1222 |
__le32 *rxd = |
| 1223 |
(__le32 *)(entry->skb->data + |
| 1224 |
(entry_priv->urb->actual_length - |
| 1225 |
entry->queue->desc_size)); |
| 1226 |
u32 word0; |
| 1227 |
u32 word1; |
| 1228 |
|
| 1229 |
/* |
| 1230 |
* Copy descriptor to the skbdesc->desc buffer, making it safe from moving of |
| 1231 |
* frame data in rt2x00usb. |
| 1232 |
*/ |
| 1233 |
memcpy(skbdesc->desc, rxd, skbdesc->desc_len); |
| 1234 |
rxd = (__le32 *)skbdesc->desc; |
| 1235 |
|
| 1236 |
/* |
| 1237 |
* It is now safe to read the descriptor on all architectures. |
| 1238 |
*/ |
| 1239 |
word0 = rt2x00_desc_read(rxd, 0); |
| 1240 |
word1 = rt2x00_desc_read(rxd, 1); |
| 1241 |
|
| 1242 |
if (rt2x00_get_field32(word0, RXD_W0_CRC_ERROR)) |
| 1243 |
rxdesc->flags |= RX_FLAG_FAILED_FCS_CRC; |
| 1244 |
if (rt2x00_get_field32(word0, RXD_W0_PHYSICAL_ERROR)) |
| 1245 |
rxdesc->flags |= RX_FLAG_FAILED_PLCP_CRC; |
| 1246 |
|
| 1247 |
rxdesc->cipher = rt2x00_get_field32(word0, RXD_W0_CIPHER); |
| 1248 |
if (rt2x00_get_field32(word0, RXD_W0_CIPHER_ERROR)) |
| 1249 |
rxdesc->cipher_status = RX_CRYPTO_FAIL_KEY; |
| 1250 |
|
| 1251 |
if (rxdesc->cipher != CIPHER_NONE) { |
| 1252 |
rxdesc->iv[0] = _rt2x00_desc_read(rxd, 2); |
| 1253 |
rxdesc->iv[1] = _rt2x00_desc_read(rxd, 3); |
| 1254 |
rxdesc->dev_flags |= RXDONE_CRYPTO_IV; |
| 1255 |
|
| 1256 |
/* ICV is located at the end of frame */ |
| 1257 |
|
| 1258 |
rxdesc->flags |= RX_FLAG_MMIC_STRIPPED; |
| 1259 |
if (rxdesc->cipher_status == RX_CRYPTO_SUCCESS) |
| 1260 |
rxdesc->flags |= RX_FLAG_DECRYPTED; |
| 1261 |
else if (rxdesc->cipher_status == RX_CRYPTO_FAIL_MIC) |
| 1262 |
rxdesc->flags |= RX_FLAG_MMIC_ERROR; |
| 1263 |
} |
| 1264 |
|
| 1265 |
/* |
| 1266 |
* Obtain the status about this packet. |
| 1267 |
* When frame was received with an OFDM bitrate, |
| 1268 |
* the signal is the PLCP value. If it was received with |
| 1269 |
* a CCK bitrate the signal is the rate in 100kbit/s. |
| 1270 |
*/ |
| 1271 |
rxdesc->signal = rt2x00_get_field32(word1, RXD_W1_SIGNAL); |
| 1272 |
rxdesc->rssi = |
| 1273 |
rt2x00_get_field32(word1, RXD_W1_RSSI) - rt2x00dev->rssi_offset; |
| 1274 |
rxdesc->size = rt2x00_get_field32(word0, RXD_W0_DATABYTE_COUNT); |
| 1275 |
|
| 1276 |
if (rt2x00_get_field32(word0, RXD_W0_OFDM)) |
| 1277 |
rxdesc->dev_flags |= RXDONE_SIGNAL_PLCP; |
| 1278 |
else |
| 1279 |
rxdesc->dev_flags |= RXDONE_SIGNAL_BITRATE; |
| 1280 |
if (rt2x00_get_field32(word0, RXD_W0_MY_BSS)) |
| 1281 |
rxdesc->dev_flags |= RXDONE_MY_BSS; |
| 1282 |
|
| 1283 |
/* |
| 1284 |
* Adjust the skb memory window to the frame boundaries. |
| 1285 |
*/ |
| 1286 |
skb_trim(entry->skb, rxdesc->size); |
| 1287 |
} |
| 1288 |
|
| 1289 |
/* |
| 1290 |
* Interrupt functions. |
| 1291 |
*/ |
| 1292 |
static void rt2500usb_beacondone(struct urb *urb) |
| 1293 |
{ |
| 1294 |
struct queue_entry *entry = (struct queue_entry *)urb->context; |
| 1295 |
struct queue_entry_priv_usb_bcn *bcn_priv = entry->priv_data; |
| 1296 |
|
| 1297 |
if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &entry->queue->rt2x00dev->flags)) |
| 1298 |
return; |
| 1299 |
|
| 1300 |
/* |
| 1301 |
* Check if this was the guardian beacon, |
| 1302 |
* if that was the case we need to send the real beacon now. |
| 1303 |
* Otherwise we should free the sk_buffer, the device |
| 1304 |
* should be doing the rest of the work now. |
| 1305 |
*/ |
| 1306 |
if (bcn_priv->guardian_urb == urb) { |
| 1307 |
usb_submit_urb(bcn_priv->urb, GFP_ATOMIC); |
| 1308 |
} else if (bcn_priv->urb == urb) { |
| 1309 |
dev_kfree_skb(entry->skb); |
| 1310 |
entry->skb = NULL; |
| 1311 |
} |
| 1312 |
} |
| 1313 |
|
| 1314 |
/* |
| 1315 |
* Device probe functions. |
| 1316 |
*/ |
| 1317 |
static int rt2500usb_validate_eeprom(struct rt2x00_dev *rt2x00dev) |
| 1318 |
{ |
| 1319 |
u16 word; |
| 1320 |
u8 *mac; |
| 1321 |
u8 bbp; |
| 1322 |
|
| 1323 |
rt2x00usb_eeprom_read(rt2x00dev, rt2x00dev->eeprom, EEPROM_SIZE); |
| 1324 |
|
| 1325 |
/* |
| 1326 |
* Start validation of the data that has been read. |
| 1327 |
*/ |
| 1328 |
mac = rt2x00_eeprom_addr(rt2x00dev, EEPROM_MAC_ADDR_0); |
| 1329 |
rt2x00lib_set_mac_address(rt2x00dev, mac); |
| 1330 |
|
| 1331 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA); |
| 1332 |
if (word == 0xffff) { |
| 1333 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_NUM, 2); |
| 1334 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_TX_DEFAULT, |
| 1335 |
ANTENNA_SW_DIVERSITY); |
| 1336 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_RX_DEFAULT, |
| 1337 |
ANTENNA_SW_DIVERSITY); |
| 1338 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_LED_MODE, |
| 1339 |
LED_MODE_DEFAULT); |
| 1340 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_DYN_TXAGC, 0); |
| 1341 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_HARDWARE_RADIO, 0); |
| 1342 |
rt2x00_set_field16(&word, EEPROM_ANTENNA_RF_TYPE, RF2522); |
| 1343 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_ANTENNA, word); |
| 1344 |
rt2x00_eeprom_dbg(rt2x00dev, "Antenna: 0x%04x\n", word); |
| 1345 |
} |
| 1346 |
|
| 1347 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC); |
| 1348 |
if (word == 0xffff) { |
| 1349 |
rt2x00_set_field16(&word, EEPROM_NIC_CARDBUS_ACCEL, 0); |
| 1350 |
rt2x00_set_field16(&word, EEPROM_NIC_DYN_BBP_TUNE, 0); |
| 1351 |
rt2x00_set_field16(&word, EEPROM_NIC_CCK_TX_POWER, 0); |
| 1352 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_NIC, word); |
| 1353 |
rt2x00_eeprom_dbg(rt2x00dev, "NIC: 0x%04x\n", word); |
| 1354 |
} |
| 1355 |
|
| 1356 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_CALIBRATE_OFFSET); |
| 1357 |
if (word == 0xffff) { |
| 1358 |
rt2x00_set_field16(&word, EEPROM_CALIBRATE_OFFSET_RSSI, |
| 1359 |
DEFAULT_RSSI_OFFSET); |
| 1360 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_CALIBRATE_OFFSET, word); |
| 1361 |
rt2x00_eeprom_dbg(rt2x00dev, "Calibrate offset: 0x%04x\n", |
| 1362 |
word); |
| 1363 |
} |
| 1364 |
|
| 1365 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE); |
| 1366 |
if (word == 0xffff) { |
| 1367 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_THRESHOLD, 45); |
| 1368 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE, word); |
| 1369 |
rt2x00_eeprom_dbg(rt2x00dev, "BBPtune: 0x%04x\n", word); |
| 1370 |
} |
| 1371 |
|
| 1372 |
/* |
| 1373 |
* Switch lower vgc bound to current BBP R17 value, |
| 1374 |
* lower the value a bit for better quality. |
| 1375 |
*/ |
| 1376 |
bbp = rt2500usb_bbp_read(rt2x00dev, 17); |
| 1377 |
bbp -= 6; |
| 1378 |
|
| 1379 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_VGC); |
| 1380 |
if (word == 0xffff) { |
| 1381 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCUPPER, 0x40); |
| 1382 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp); |
| 1383 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word); |
| 1384 |
rt2x00_eeprom_dbg(rt2x00dev, "BBPtune vgc: 0x%04x\n", word); |
| 1385 |
} else { |
| 1386 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp); |
| 1387 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word); |
| 1388 |
} |
| 1389 |
|
| 1390 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R17); |
| 1391 |
if (word == 0xffff) { |
| 1392 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R17_LOW, 0x48); |
| 1393 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R17_HIGH, 0x41); |
| 1394 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R17, word); |
| 1395 |
rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r17: 0x%04x\n", word); |
| 1396 |
} |
| 1397 |
|
| 1398 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R24); |
| 1399 |
if (word == 0xffff) { |
| 1400 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R24_LOW, 0x40); |
| 1401 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R24_HIGH, 0x80); |
| 1402 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R24, word); |
| 1403 |
rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r24: 0x%04x\n", word); |
| 1404 |
} |
| 1405 |
|
| 1406 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R25); |
| 1407 |
if (word == 0xffff) { |
| 1408 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R25_LOW, 0x40); |
| 1409 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R25_HIGH, 0x50); |
| 1410 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R25, word); |
| 1411 |
rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r25: 0x%04x\n", word); |
| 1412 |
} |
| 1413 |
|
| 1414 |
word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R61); |
| 1415 |
if (word == 0xffff) { |
| 1416 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R61_LOW, 0x60); |
| 1417 |
rt2x00_set_field16(&word, EEPROM_BBPTUNE_R61_HIGH, 0x6d); |
| 1418 |
rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R61, word); |
| 1419 |
rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r61: 0x%04x\n", word); |
| 1420 |
} |
| 1421 |
|
| 1422 |
return 0; |
| 1423 |
} |
| 1424 |
|
| 1425 |
static int rt2500usb_init_eeprom(struct rt2x00_dev *rt2x00dev) |
| 1426 |
{ |
| 1427 |
u16 reg; |
| 1428 |
u16 value; |
| 1429 |
u16 eeprom; |
| 1430 |
|
| 1431 |
/* |
| 1432 |
* Read EEPROM word for configuration. |
| 1433 |
*/ |
| 1434 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA); |
| 1435 |
|
| 1436 |
/* |
| 1437 |
* Identify RF chipset. |
| 1438 |
*/ |
| 1439 |
value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RF_TYPE); |
| 1440 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR0); |
| 1441 |
rt2x00_set_chip(rt2x00dev, RT2570, value, reg); |
| 1442 |
|
| 1443 |
if (((reg & 0xfff0) != 0) || ((reg & 0x0000000f) == 0)) { |
| 1444 |
rt2x00_err(rt2x00dev, "Invalid RT chipset detected\n"); |
| 1445 |
return -ENODEV; |
| 1446 |
} |
| 1447 |
|
| 1448 |
if (!rt2x00_rf(rt2x00dev, RF2522) && |
| 1449 |
!rt2x00_rf(rt2x00dev, RF2523) && |
| 1450 |
!rt2x00_rf(rt2x00dev, RF2524) && |
| 1451 |
!rt2x00_rf(rt2x00dev, RF2525) && |
| 1452 |
!rt2x00_rf(rt2x00dev, RF2525E) && |
| 1453 |
!rt2x00_rf(rt2x00dev, RF5222)) { |
| 1454 |
rt2x00_err(rt2x00dev, "Invalid RF chipset detected\n"); |
| 1455 |
return -ENODEV; |
| 1456 |
} |
| 1457 |
|
| 1458 |
/* |
| 1459 |
* Identify default antenna configuration. |
| 1460 |
*/ |
| 1461 |
rt2x00dev->default_ant.tx = |
| 1462 |
rt2x00_get_field16(eeprom, EEPROM_ANTENNA_TX_DEFAULT); |
| 1463 |
rt2x00dev->default_ant.rx = |
| 1464 |
rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RX_DEFAULT); |
| 1465 |
|
| 1466 |
/* |
| 1467 |
* When the eeprom indicates SW_DIVERSITY use HW_DIVERSITY instead. |
| 1468 |
* I am not 100% sure about this, but the legacy drivers do not |
| 1469 |
* indicate antenna swapping in software is required when |
| 1470 |
* diversity is enabled. |
| 1471 |
*/ |
| 1472 |
if (rt2x00dev->default_ant.tx == ANTENNA_SW_DIVERSITY) |
| 1473 |
rt2x00dev->default_ant.tx = ANTENNA_HW_DIVERSITY; |
| 1474 |
if (rt2x00dev->default_ant.rx == ANTENNA_SW_DIVERSITY) |
| 1475 |
rt2x00dev->default_ant.rx = ANTENNA_HW_DIVERSITY; |
| 1476 |
|
| 1477 |
/* |
| 1478 |
* Store led mode, for correct led behaviour. |
| 1479 |
*/ |
| 1480 |
#ifdef CONFIG_RT2X00_LIB_LEDS |
| 1481 |
value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_LED_MODE); |
| 1482 |
|
| 1483 |
rt2500usb_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO); |
| 1484 |
if (value == LED_MODE_TXRX_ACTIVITY || |
| 1485 |
value == LED_MODE_DEFAULT || |
| 1486 |
value == LED_MODE_ASUS) |
| 1487 |
rt2500usb_init_led(rt2x00dev, &rt2x00dev->led_qual, |
| 1488 |
LED_TYPE_ACTIVITY); |
| 1489 |
#endif /* CONFIG_RT2X00_LIB_LEDS */ |
| 1490 |
|
| 1491 |
/* |
| 1492 |
* Detect if this device has an hardware controlled radio. |
| 1493 |
*/ |
| 1494 |
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_HARDWARE_RADIO)) |
| 1495 |
__set_bit(CAPABILITY_HW_BUTTON, &rt2x00dev->cap_flags); |
| 1496 |
|
| 1497 |
/* |
| 1498 |
* Read the RSSI <-> dBm offset information. |
| 1499 |
*/ |
| 1500 |
eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_CALIBRATE_OFFSET); |
| 1501 |
rt2x00dev->rssi_offset = |
| 1502 |
rt2x00_get_field16(eeprom, EEPROM_CALIBRATE_OFFSET_RSSI); |
| 1503 |
|
| 1504 |
return 0; |
| 1505 |
} |
| 1506 |
|
| 1507 |
/* |
| 1508 |
* RF value list for RF2522 |
| 1509 |
* Supports: 2.4 GHz |
| 1510 |
*/ |
| 1511 |
static const struct rf_channel rf_vals_bg_2522[] = { |
| 1512 |
{ 1, 0x00002050, 0x000c1fda, 0x00000101, 0 }, |
| 1513 |
{ 2, 0x00002050, 0x000c1fee, 0x00000101, 0 }, |
| 1514 |
{ 3, 0x00002050, 0x000c2002, 0x00000101, 0 }, |
| 1515 |
{ 4, 0x00002050, 0x000c2016, 0x00000101, 0 }, |
| 1516 |
{ 5, 0x00002050, 0x000c202a, 0x00000101, 0 }, |
| 1517 |
{ 6, 0x00002050, 0x000c203e, 0x00000101, 0 }, |
| 1518 |
{ 7, 0x00002050, 0x000c2052, 0x00000101, 0 }, |
| 1519 |
{ 8, 0x00002050, 0x000c2066, 0x00000101, 0 }, |
| 1520 |
{ 9, 0x00002050, 0x000c207a, 0x00000101, 0 }, |
| 1521 |
{ 10, 0x00002050, 0x000c208e, 0x00000101, 0 }, |
| 1522 |
{ 11, 0x00002050, 0x000c20a2, 0x00000101, 0 }, |
| 1523 |
{ 12, 0x00002050, 0x000c20b6, 0x00000101, 0 }, |
| 1524 |
{ 13, 0x00002050, 0x000c20ca, 0x00000101, 0 }, |
| 1525 |
{ 14, 0x00002050, 0x000c20fa, 0x00000101, 0 }, |
| 1526 |
}; |
| 1527 |
|
| 1528 |
/* |
| 1529 |
* RF value list for RF2523 |
| 1530 |
* Supports: 2.4 GHz |
| 1531 |
*/ |
| 1532 |
static const struct rf_channel rf_vals_bg_2523[] = { |
| 1533 |
{ 1, 0x00022010, 0x00000c9e, 0x000e0111, 0x00000a1b }, |
| 1534 |
{ 2, 0x00022010, 0x00000ca2, 0x000e0111, 0x00000a1b }, |
| 1535 |
{ 3, 0x00022010, 0x00000ca6, 0x000e0111, 0x00000a1b }, |
| 1536 |
{ 4, 0x00022010, 0x00000caa, 0x000e0111, 0x00000a1b }, |
| 1537 |
{ 5, 0x00022010, 0x00000cae, 0x000e0111, 0x00000a1b }, |
| 1538 |
{ 6, 0x00022010, 0x00000cb2, 0x000e0111, 0x00000a1b }, |
| 1539 |
{ 7, 0x00022010, 0x00000cb6, 0x000e0111, 0x00000a1b }, |
| 1540 |
{ 8, 0x00022010, 0x00000cba, 0x000e0111, 0x00000a1b }, |
| 1541 |
{ 9, 0x00022010, 0x00000cbe, 0x000e0111, 0x00000a1b }, |
| 1542 |
{ 10, 0x00022010, 0x00000d02, 0x000e0111, 0x00000a1b }, |
| 1543 |
{ 11, 0x00022010, 0x00000d06, 0x000e0111, 0x00000a1b }, |
| 1544 |
{ 12, 0x00022010, 0x00000d0a, 0x000e0111, 0x00000a1b }, |
| 1545 |
{ 13, 0x00022010, 0x00000d0e, 0x000e0111, 0x00000a1b }, |
| 1546 |
{ 14, 0x00022010, 0x00000d1a, 0x000e0111, 0x00000a03 }, |
| 1547 |
}; |
| 1548 |
|
| 1549 |
/* |
| 1550 |
* RF value list for RF2524 |
| 1551 |
* Supports: 2.4 GHz |
| 1552 |
*/ |
| 1553 |
static const struct rf_channel rf_vals_bg_2524[] = { |
| 1554 |
{ 1, 0x00032020, 0x00000c9e, 0x00000101, 0x00000a1b }, |
| 1555 |
{ 2, 0x00032020, 0x00000ca2, 0x00000101, 0x00000a1b }, |
| 1556 |
{ 3, 0x00032020, 0x00000ca6, 0x00000101, 0x00000a1b }, |
| 1557 |
{ 4, 0x00032020, 0x00000caa, 0x00000101, 0x00000a1b }, |
| 1558 |
{ 5, 0x00032020, 0x00000cae, 0x00000101, 0x00000a1b }, |
| 1559 |
{ 6, 0x00032020, 0x00000cb2, 0x00000101, 0x00000a1b }, |
| 1560 |
{ 7, 0x00032020, 0x00000cb6, 0x00000101, 0x00000a1b }, |
| 1561 |
{ 8, 0x00032020, 0x00000cba, 0x00000101, 0x00000a1b }, |
| 1562 |
{ 9, 0x00032020, 0x00000cbe, 0x00000101, 0x00000a1b }, |
| 1563 |
{ 10, 0x00032020, 0x00000d02, 0x00000101, 0x00000a1b }, |
| 1564 |
{ 11, 0x00032020, 0x00000d06, 0x00000101, 0x00000a1b }, |
| 1565 |
{ 12, 0x00032020, 0x00000d0a, 0x00000101, 0x00000a1b }, |
| 1566 |
{ 13, 0x00032020, 0x00000d0e, 0x00000101, 0x00000a1b }, |
| 1567 |
{ 14, 0x00032020, 0x00000d1a, 0x00000101, 0x00000a03 }, |
| 1568 |
}; |
| 1569 |
|
| 1570 |
/* |
| 1571 |
* RF value list for RF2525 |
| 1572 |
* Supports: 2.4 GHz |
| 1573 |
*/ |
| 1574 |
static const struct rf_channel rf_vals_bg_2525[] = { |
| 1575 |
{ 1, 0x00022020, 0x00080c9e, 0x00060111, 0x00000a1b }, |
| 1576 |
{ 2, 0x00022020, 0x00080ca2, 0x00060111, 0x00000a1b }, |
| 1577 |
{ 3, 0x00022020, 0x00080ca6, 0x00060111, 0x00000a1b }, |
| 1578 |
{ 4, 0x00022020, 0x00080caa, 0x00060111, 0x00000a1b }, |
| 1579 |
{ 5, 0x00022020, 0x00080cae, 0x00060111, 0x00000a1b }, |
| 1580 |
{ 6, 0x00022020, 0x00080cb2, 0x00060111, 0x00000a1b }, |
| 1581 |
{ 7, 0x00022020, 0x00080cb6, 0x00060111, 0x00000a1b }, |
| 1582 |
{ 8, 0x00022020, 0x00080cba, 0x00060111, 0x00000a1b }, |
| 1583 |
{ 9, 0x00022020, 0x00080cbe, 0x00060111, 0x00000a1b }, |
| 1584 |
{ 10, 0x00022020, 0x00080d02, 0x00060111, 0x00000a1b }, |
| 1585 |
{ 11, 0x00022020, 0x00080d06, 0x00060111, 0x00000a1b }, |
| 1586 |
{ 12, 0x00022020, 0x00080d0a, 0x00060111, 0x00000a1b }, |
| 1587 |
{ 13, 0x00022020, 0x00080d0e, 0x00060111, 0x00000a1b }, |
| 1588 |
{ 14, 0x00022020, 0x00080d1a, 0x00060111, 0x00000a03 }, |
| 1589 |
}; |
| 1590 |
|
| 1591 |
/* |
| 1592 |
* RF value list for RF2525e |
| 1593 |
* Supports: 2.4 GHz |
| 1594 |
*/ |
| 1595 |
static const struct rf_channel rf_vals_bg_2525e[] = { |
| 1596 |
{ 1, 0x00022010, 0x0000089a, 0x00060111, 0x00000e1b }, |
| 1597 |
{ 2, 0x00022010, 0x0000089e, 0x00060111, 0x00000e07 }, |
| 1598 |
{ 3, 0x00022010, 0x0000089e, 0x00060111, 0x00000e1b }, |
| 1599 |
{ 4, 0x00022010, 0x000008a2, 0x00060111, 0x00000e07 }, |
| 1600 |
{ 5, 0x00022010, 0x000008a2, 0x00060111, 0x00000e1b }, |
| 1601 |
{ 6, 0x00022010, 0x000008a6, 0x00060111, 0x00000e07 }, |
| 1602 |
{ 7, 0x00022010, 0x000008a6, 0x00060111, 0x00000e1b }, |
| 1603 |
{ 8, 0x00022010, 0x000008aa, 0x00060111, 0x00000e07 }, |
| 1604 |
{ 9, 0x00022010, 0x000008aa, 0x00060111, 0x00000e1b }, |
| 1605 |
{ 10, 0x00022010, 0x000008ae, 0x00060111, 0x00000e07 }, |
| 1606 |
{ 11, 0x00022010, 0x000008ae, 0x00060111, 0x00000e1b }, |
| 1607 |
{ 12, 0x00022010, 0x000008b2, 0x00060111, 0x00000e07 }, |
| 1608 |
{ 13, 0x00022010, 0x000008b2, 0x00060111, 0x00000e1b }, |
| 1609 |
{ 14, 0x00022010, 0x000008b6, 0x00060111, 0x00000e23 }, |
| 1610 |
}; |
| 1611 |
|
| 1612 |
/* |
| 1613 |
* RF value list for RF5222 |
| 1614 |
* Supports: 2.4 GHz & 5.2 GHz |
| 1615 |
*/ |
| 1616 |
static const struct rf_channel rf_vals_5222[] = { |
| 1617 |
{ 1, 0x00022020, 0x00001136, 0x00000101, 0x00000a0b }, |
| 1618 |
{ 2, 0x00022020, 0x0000113a, 0x00000101, 0x00000a0b }, |
| 1619 |
{ 3, 0x00022020, 0x0000113e, 0x00000101, 0x00000a0b }, |
| 1620 |
{ 4, 0x00022020, 0x00001182, 0x00000101, 0x00000a0b }, |
| 1621 |
{ 5, 0x00022020, 0x00001186, 0x00000101, 0x00000a0b }, |
| 1622 |
{ 6, 0x00022020, 0x0000118a, 0x00000101, 0x00000a0b }, |
| 1623 |
{ 7, 0x00022020, 0x0000118e, 0x00000101, 0x00000a0b }, |
| 1624 |
{ 8, 0x00022020, 0x00001192, 0x00000101, 0x00000a0b }, |
| 1625 |
{ 9, 0x00022020, 0x00001196, 0x00000101, 0x00000a0b }, |
| 1626 |
{ 10, 0x00022020, 0x0000119a, 0x00000101, 0x00000a0b }, |
| 1627 |
{ 11, 0x00022020, 0x0000119e, 0x00000101, 0x00000a0b }, |
| 1628 |
{ 12, 0x00022020, 0x000011a2, 0x00000101, 0x00000a0b }, |
| 1629 |
{ 13, 0x00022020, 0x000011a6, 0x00000101, 0x00000a0b }, |
| 1630 |
{ 14, 0x00022020, 0x000011ae, 0x00000101, 0x00000a1b }, |
| 1631 |
|
| 1632 |
/* 802.11 UNI / HyperLan 2 */ |
| 1633 |
{ 36, 0x00022010, 0x00018896, 0x00000101, 0x00000a1f }, |
| 1634 |
{ 40, 0x00022010, 0x0001889a, 0x00000101, 0x00000a1f }, |
| 1635 |
{ 44, 0x00022010, 0x0001889e, 0x00000101, 0x00000a1f }, |
| 1636 |
{ 48, 0x00022010, 0x000188a2, 0x00000101, 0x00000a1f }, |
| 1637 |
{ 52, 0x00022010, 0x000188a6, 0x00000101, 0x00000a1f }, |
| 1638 |
{ 66, 0x00022010, 0x000188aa, 0x00000101, 0x00000a1f }, |
| 1639 |
{ 60, 0x00022010, 0x000188ae, 0x00000101, 0x00000a1f }, |
| 1640 |
{ 64, 0x00022010, 0x000188b2, 0x00000101, 0x00000a1f }, |
| 1641 |
|
| 1642 |
/* 802.11 HyperLan 2 */ |
| 1643 |
{ 100, 0x00022010, 0x00008802, 0x00000101, 0x00000a0f }, |
| 1644 |
{ 104, 0x00022010, 0x00008806, 0x00000101, 0x00000a0f }, |
| 1645 |
{ 108, 0x00022010, 0x0000880a, 0x00000101, 0x00000a0f }, |
| 1646 |
{ 112, 0x00022010, 0x0000880e, 0x00000101, 0x00000a0f }, |
| 1647 |
{ 116, 0x00022010, 0x00008812, 0x00000101, 0x00000a0f }, |
| 1648 |
{ 120, 0x00022010, 0x00008816, 0x00000101, 0x00000a0f }, |
| 1649 |
{ 124, 0x00022010, 0x0000881a, 0x00000101, 0x00000a0f }, |
| 1650 |
{ 128, 0x00022010, 0x0000881e, 0x00000101, 0x00000a0f }, |
| 1651 |
{ 132, 0x00022010, 0x00008822, 0x00000101, 0x00000a0f }, |
| 1652 |
{ 136, 0x00022010, 0x00008826, 0x00000101, 0x00000a0f }, |
| 1653 |
|
| 1654 |
/* 802.11 UNII */ |
| 1655 |
{ 140, 0x00022010, 0x0000882a, 0x00000101, 0x00000a0f }, |
| 1656 |
{ 149, 0x00022020, 0x000090a6, 0x00000101, 0x00000a07 }, |
| 1657 |
{ 153, 0x00022020, 0x000090ae, 0x00000101, 0x00000a07 }, |
| 1658 |
{ 157, 0x00022020, 0x000090b6, 0x00000101, 0x00000a07 }, |
| 1659 |
{ 161, 0x00022020, 0x000090be, 0x00000101, 0x00000a07 }, |
| 1660 |
}; |
| 1661 |
|
| 1662 |
static int rt2500usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev) |
| 1663 |
{ |
| 1664 |
struct hw_mode_spec *spec = &rt2x00dev->spec; |
| 1665 |
struct channel_info *info; |
| 1666 |
u8 *tx_power; |
| 1667 |
unsigned int i; |
| 1668 |
|
| 1669 |
/* |
| 1670 |
* Initialize all hw fields. |
| 1671 |
* |
| 1672 |
* Don't set IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING unless we are |
| 1673 |
* capable of sending the buffered frames out after the DTIM |
| 1674 |
* transmission using rt2x00lib_beacondone. This will send out |
| 1675 |
* multicast and broadcast traffic immediately instead of buffering it |
| 1676 |
* infinitly and thus dropping it after some time. |
| 1677 |
*/ |
| 1678 |
ieee80211_hw_set(rt2x00dev->hw, PS_NULLFUNC_STACK); |
| 1679 |
ieee80211_hw_set(rt2x00dev->hw, SUPPORTS_PS); |
| 1680 |
ieee80211_hw_set(rt2x00dev->hw, RX_INCLUDES_FCS); |
| 1681 |
ieee80211_hw_set(rt2x00dev->hw, SIGNAL_DBM); |
| 1682 |
|
| 1683 |
/* |
| 1684 |
* Disable powersaving as default. |
| 1685 |
*/ |
| 1686 |
rt2x00dev->hw->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT; |
| 1687 |
|
| 1688 |
SET_IEEE80211_DEV(rt2x00dev->hw, rt2x00dev->dev); |
| 1689 |
SET_IEEE80211_PERM_ADDR(rt2x00dev->hw, |
| 1690 |
rt2x00_eeprom_addr(rt2x00dev, |
| 1691 |
EEPROM_MAC_ADDR_0)); |
| 1692 |
|
| 1693 |
/* |
| 1694 |
* Initialize hw_mode information. |
| 1695 |
*/ |
| 1696 |
spec->supported_bands = SUPPORT_BAND_2GHZ; |
| 1697 |
spec->supported_rates = SUPPORT_RATE_CCK | SUPPORT_RATE_OFDM; |
| 1698 |
|
| 1699 |
if (rt2x00_rf(rt2x00dev, RF2522)) { |
| 1700 |
spec->num_channels = ARRAY_SIZE(rf_vals_bg_2522); |
| 1701 |
spec->channels = rf_vals_bg_2522; |
| 1702 |
} else if (rt2x00_rf(rt2x00dev, RF2523)) { |
| 1703 |
spec->num_channels = ARRAY_SIZE(rf_vals_bg_2523); |
| 1704 |
spec->channels = rf_vals_bg_2523; |
| 1705 |
} else if (rt2x00_rf(rt2x00dev, RF2524)) { |
| 1706 |
spec->num_channels = ARRAY_SIZE(rf_vals_bg_2524); |
| 1707 |
spec->channels = rf_vals_bg_2524; |
| 1708 |
} else if (rt2x00_rf(rt2x00dev, RF2525)) { |
| 1709 |
spec->num_channels = ARRAY_SIZE(rf_vals_bg_2525); |
| 1710 |
spec->channels = rf_vals_bg_2525; |
| 1711 |
} else if (rt2x00_rf(rt2x00dev, RF2525E)) { |
| 1712 |
spec->num_channels = ARRAY_SIZE(rf_vals_bg_2525e); |
| 1713 |
spec->channels = rf_vals_bg_2525e; |
| 1714 |
} else if (rt2x00_rf(rt2x00dev, RF5222)) { |
| 1715 |
spec->supported_bands |= SUPPORT_BAND_5GHZ; |
| 1716 |
spec->num_channels = ARRAY_SIZE(rf_vals_5222); |
| 1717 |
spec->channels = rf_vals_5222; |
| 1718 |
} |
| 1719 |
|
| 1720 |
/* |
| 1721 |
* Create channel information array |
| 1722 |
*/ |
| 1723 |
info = kzalloc_objs(*info, spec->num_channels); |
| 1724 |
if (!info) |
| 1725 |
return -ENOMEM; |
| 1726 |
|
| 1727 |
spec->channels_info = info; |
| 1728 |
|
| 1729 |
tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_START); |
| 1730 |
for (i = 0; i < 14; i++) { |
| 1731 |
info[i].max_power = MAX_TXPOWER; |
| 1732 |
info[i].default_power1 = TXPOWER_FROM_DEV(tx_power[i]); |
| 1733 |
} |
| 1734 |
|
| 1735 |
if (spec->num_channels > 14) { |
| 1736 |
for (i = 14; i < spec->num_channels; i++) { |
| 1737 |
info[i].max_power = MAX_TXPOWER; |
| 1738 |
info[i].default_power1 = DEFAULT_TXPOWER; |
| 1739 |
} |
| 1740 |
} |
| 1741 |
|
| 1742 |
return 0; |
| 1743 |
} |
| 1744 |
|
| 1745 |
static int rt2500usb_probe_hw(struct rt2x00_dev *rt2x00dev) |
| 1746 |
{ |
| 1747 |
int retval; |
| 1748 |
u16 reg; |
| 1749 |
|
| 1750 |
/* |
| 1751 |
* Allocate eeprom data. |
| 1752 |
*/ |
| 1753 |
retval = rt2500usb_validate_eeprom(rt2x00dev); |
| 1754 |
if (retval) |
| 1755 |
return retval; |
| 1756 |
|
| 1757 |
retval = rt2500usb_init_eeprom(rt2x00dev); |
| 1758 |
if (retval) |
| 1759 |
return retval; |
| 1760 |
|
| 1761 |
/* |
| 1762 |
* Enable rfkill polling by setting GPIO direction of the |
| 1763 |
* rfkill switch GPIO pin correctly. |
| 1764 |
*/ |
| 1765 |
reg = rt2500usb_register_read(rt2x00dev, MAC_CSR19); |
| 1766 |
rt2x00_set_field16(®, MAC_CSR19_DIR0, 0); |
| 1767 |
rt2500usb_register_write(rt2x00dev, MAC_CSR19, reg); |
| 1768 |
|
| 1769 |
/* |
| 1770 |
* Initialize hw specifications. |
| 1771 |
*/ |
| 1772 |
retval = rt2500usb_probe_hw_mode(rt2x00dev); |
| 1773 |
if (retval) |
| 1774 |
return retval; |
| 1775 |
|
| 1776 |
/* |
| 1777 |
* This device requires the atim queue |
| 1778 |
*/ |
| 1779 |
__set_bit(REQUIRE_ATIM_QUEUE, &rt2x00dev->cap_flags); |
| 1780 |
__set_bit(REQUIRE_BEACON_GUARD, &rt2x00dev->cap_flags); |
| 1781 |
if (!modparam_nohwcrypt) { |
| 1782 |
__set_bit(CAPABILITY_HW_CRYPTO, &rt2x00dev->cap_flags); |
| 1783 |
__set_bit(REQUIRE_COPY_IV, &rt2x00dev->cap_flags); |
| 1784 |
} |
| 1785 |
__set_bit(REQUIRE_SW_SEQNO, &rt2x00dev->cap_flags); |
| 1786 |
__set_bit(REQUIRE_PS_AUTOWAKE, &rt2x00dev->cap_flags); |
| 1787 |
|
| 1788 |
/* |
| 1789 |
* Set the rssi offset. |
| 1790 |
*/ |
| 1791 |
rt2x00dev->rssi_offset = DEFAULT_RSSI_OFFSET; |
| 1792 |
|
| 1793 |
return 0; |
| 1794 |
} |
| 1795 |
|
| 1796 |
static const struct ieee80211_ops rt2500usb_mac80211_ops = { |
| 1797 |
.add_chanctx = ieee80211_emulate_add_chanctx, |
| 1798 |
.remove_chanctx = ieee80211_emulate_remove_chanctx, |
| 1799 |
.change_chanctx = ieee80211_emulate_change_chanctx, |
| 1800 |
.switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx, |
| 1801 |
.tx = rt2x00mac_tx, |
| 1802 |
.wake_tx_queue = ieee80211_handle_wake_tx_queue, |
| 1803 |
.start = rt2x00mac_start, |
| 1804 |
.stop = rt2x00mac_stop, |
| 1805 |
.add_interface = rt2x00mac_add_interface, |
| 1806 |
.remove_interface = rt2x00mac_remove_interface, |
| 1807 |
.config = rt2x00mac_config, |
| 1808 |
.configure_filter = rt2x00mac_configure_filter, |
| 1809 |
.set_tim = rt2x00mac_set_tim, |
| 1810 |
.set_key = rt2x00mac_set_key, |
| 1811 |
.sw_scan_start = rt2x00mac_sw_scan_start, |
| 1812 |
.sw_scan_complete = rt2x00mac_sw_scan_complete, |
| 1813 |
.get_stats = rt2x00mac_get_stats, |
| 1814 |
.bss_info_changed = rt2x00mac_bss_info_changed, |
| 1815 |
.conf_tx = rt2x00mac_conf_tx, |
| 1816 |
.rfkill_poll = rt2x00mac_rfkill_poll, |
| 1817 |
.flush = rt2x00mac_flush, |
| 1818 |
.set_antenna = rt2x00mac_set_antenna, |
| 1819 |
.get_antenna = rt2x00mac_get_antenna, |
| 1820 |
.get_ringparam = rt2x00mac_get_ringparam, |
| 1821 |
.tx_frames_pending = rt2x00mac_tx_frames_pending, |
| 1822 |
}; |
| 1823 |
|
| 1824 |
static const struct rt2x00lib_ops rt2500usb_rt2x00_ops = { |
| 1825 |
.probe_hw = rt2500usb_probe_hw, |
| 1826 |
.initialize = rt2x00usb_initialize, |
| 1827 |
.uninitialize = rt2x00usb_uninitialize, |
| 1828 |
.clear_entry = rt2x00usb_clear_entry, |
| 1829 |
.set_device_state = rt2500usb_set_device_state, |
| 1830 |
.rfkill_poll = rt2500usb_rfkill_poll, |
| 1831 |
.link_stats = rt2500usb_link_stats, |
| 1832 |
.reset_tuner = rt2500usb_reset_tuner, |
| 1833 |
.watchdog = rt2x00usb_watchdog, |
| 1834 |
.start_queue = rt2500usb_start_queue, |
| 1835 |
.kick_queue = rt2x00usb_kick_queue, |
| 1836 |
.stop_queue = rt2500usb_stop_queue, |
| 1837 |
.flush_queue = rt2x00usb_flush_queue, |
| 1838 |
.write_tx_desc = rt2500usb_write_tx_desc, |
| 1839 |
.write_beacon = rt2500usb_write_beacon, |
| 1840 |
.get_tx_data_len = rt2500usb_get_tx_data_len, |
| 1841 |
.fill_rxdone = rt2500usb_fill_rxdone, |
| 1842 |
.config_shared_key = rt2500usb_config_key, |
| 1843 |
.config_pairwise_key = rt2500usb_config_key, |
| 1844 |
.config_filter = rt2500usb_config_filter, |
| 1845 |
.config_intf = rt2500usb_config_intf, |
| 1846 |
.config_erp = rt2500usb_config_erp, |
| 1847 |
.config_ant = rt2500usb_config_ant, |
| 1848 |
.config = rt2500usb_config, |
| 1849 |
}; |
| 1850 |
|
| 1851 |
static void rt2500usb_queue_init(struct data_queue *queue) |
| 1852 |
{ |
| 1853 |
switch (queue->qid) { |
| 1854 |
case QID_RX: |
| 1855 |
queue->limit = 32; |
| 1856 |
queue->data_size = DATA_FRAME_SIZE; |
| 1857 |
queue->desc_size = RXD_DESC_SIZE; |
| 1858 |
queue->priv_size = sizeof(struct queue_entry_priv_usb); |
| 1859 |
break; |
| 1860 |
|
| 1861 |
case QID_AC_VO: |
| 1862 |
case QID_AC_VI: |
| 1863 |
case QID_AC_BE: |
| 1864 |
case QID_AC_BK: |
| 1865 |
queue->limit = 32; |
| 1866 |
queue->data_size = DATA_FRAME_SIZE; |
| 1867 |
queue->desc_size = TXD_DESC_SIZE; |
| 1868 |
queue->priv_size = sizeof(struct queue_entry_priv_usb); |
| 1869 |
break; |
| 1870 |
|
| 1871 |
case QID_BEACON: |
| 1872 |
queue->limit = 1; |
| 1873 |
queue->data_size = MGMT_FRAME_SIZE; |
| 1874 |
queue->desc_size = TXD_DESC_SIZE; |
| 1875 |
queue->priv_size = sizeof(struct queue_entry_priv_usb_bcn); |
| 1876 |
break; |
| 1877 |
|
| 1878 |
case QID_ATIM: |
| 1879 |
queue->limit = 8; |
| 1880 |
queue->data_size = DATA_FRAME_SIZE; |
| 1881 |
queue->desc_size = TXD_DESC_SIZE; |
| 1882 |
queue->priv_size = sizeof(struct queue_entry_priv_usb); |
| 1883 |
break; |
| 1884 |
|
| 1885 |
default: |
| 1886 |
BUG(); |
| 1887 |
break; |
| 1888 |
} |
| 1889 |
} |
| 1890 |
|
| 1891 |
static const struct rt2x00_ops rt2500usb_ops = { |
| 1892 |
.name = KBUILD_MODNAME, |
| 1893 |
.max_ap_intf = 1, |
| 1894 |
.eeprom_size = EEPROM_SIZE, |
| 1895 |
.rf_size = RF_SIZE, |
| 1896 |
.tx_queues = NUM_TX_QUEUES, |
| 1897 |
.queue_init = rt2500usb_queue_init, |
| 1898 |
.lib = &rt2500usb_rt2x00_ops, |
| 1899 |
.hw = &rt2500usb_mac80211_ops, |
| 1900 |
#ifdef CONFIG_RT2X00_LIB_DEBUGFS |
| 1901 |
.debugfs = &rt2500usb_rt2x00debug, |
| 1902 |
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ |
| 1903 |
}; |
| 1904 |
|
| 1905 |
/* |
| 1906 |
* rt2500usb module information. |
| 1907 |
*/ |
| 1908 |
static const struct usb_device_id rt2500usb_device_table[] = { |
| 1909 |
/* ASUS */ |
| 1910 |
{ USB_DEVICE(0x0b05, 0x1706) }, |
| 1911 |
{ USB_DEVICE(0x0b05, 0x1707) }, |
| 1912 |
/* Belkin */ |
| 1913 |
{ USB_DEVICE(0x050d, 0x7050) }, /* FCC ID: K7SF5D7050A ver. 2.x */ |
| 1914 |
{ USB_DEVICE(0x050d, 0x7051) }, |
| 1915 |
/* Cisco Systems */ |
| 1916 |
{ USB_DEVICE(0x13b1, 0x000d) }, |
| 1917 |
{ USB_DEVICE(0x13b1, 0x0011) }, |
| 1918 |
{ USB_DEVICE(0x13b1, 0x001a) }, |
| 1919 |
/* Conceptronic */ |
| 1920 |
{ USB_DEVICE(0x14b2, 0x3c02) }, |
| 1921 |
/* D-LINK */ |
| 1922 |
{ USB_DEVICE(0x2001, 0x3c00) }, |
| 1923 |
/* Gigabyte */ |
| 1924 |
{ USB_DEVICE(0x1044, 0x8001) }, |
| 1925 |
{ USB_DEVICE(0x1044, 0x8007) }, |
| 1926 |
/* Hercules */ |
| 1927 |
{ USB_DEVICE(0x06f8, 0xe000) }, |
| 1928 |
/* Melco */ |
| 1929 |
{ USB_DEVICE(0x0411, 0x005e) }, |
| 1930 |
{ USB_DEVICE(0x0411, 0x0066) }, |
| 1931 |
{ USB_DEVICE(0x0411, 0x0067) }, |
| 1932 |
{ USB_DEVICE(0x0411, 0x008b) }, |
| 1933 |
{ USB_DEVICE(0x0411, 0x0097) }, |
| 1934 |
/* MSI */ |
| 1935 |
{ USB_DEVICE(0x0db0, 0x6861) }, |
| 1936 |
{ USB_DEVICE(0x0db0, 0x6865) }, |
| 1937 |
{ USB_DEVICE(0x0db0, 0x6869) }, |
| 1938 |
/* Ralink */ |
| 1939 |
{ USB_DEVICE(0x148f, 0x1706) }, |
| 1940 |
{ USB_DEVICE(0x148f, 0x2570) }, |
| 1941 |
{ USB_DEVICE(0x148f, 0x9020) }, |
| 1942 |
/* Sagem */ |
| 1943 |
{ USB_DEVICE(0x079b, 0x004b) }, |
| 1944 |
/* Siemens */ |
| 1945 |
{ USB_DEVICE(0x0681, 0x3c06) }, |
| 1946 |
/* SMC */ |
| 1947 |
{ USB_DEVICE(0x0707, 0xee13) }, |
| 1948 |
/* Spairon */ |
| 1949 |
{ USB_DEVICE(0x114b, 0x0110) }, |
| 1950 |
/* SURECOM */ |
| 1951 |
{ USB_DEVICE(0x0769, 0x11f3) }, |
| 1952 |
/* Trust */ |
| 1953 |
{ USB_DEVICE(0x0eb0, 0x9020) }, |
| 1954 |
/* VTech */ |
| 1955 |
{ USB_DEVICE(0x0f88, 0x3012) }, |
| 1956 |
/* Zinwell */ |
| 1957 |
{ USB_DEVICE(0x5a57, 0x0260) }, |
| 1958 |
{ 0, } |
| 1959 |
}; |
| 1960 |
|
| 1961 |
MODULE_AUTHOR(DRV_PROJECT); |
| 1962 |
MODULE_VERSION(DRV_VERSION); |
| 1963 |
MODULE_DESCRIPTION("Ralink RT2500 USB Wireless LAN driver."); |
| 1964 |
MODULE_DEVICE_TABLE(usb, rt2500usb_device_table); |
| 1965 |
MODULE_LICENSE("GPL"); |
| 1966 |
|
| 1967 |
static int rt2500usb_probe(struct usb_interface *usb_intf, |
| 1968 |
const struct usb_device_id *id) |
| 1969 |
{ |
| 1970 |
return rt2x00usb_probe(usb_intf, &rt2500usb_ops); |
| 1971 |
} |
| 1972 |
|
| 1973 |
static struct usb_driver rt2500usb_driver = { |
| 1974 |
.name = KBUILD_MODNAME, |
| 1975 |
.id_table = rt2500usb_device_table, |
| 1976 |
.probe = rt2500usb_probe, |
| 1977 |
.disconnect = rt2x00usb_disconnect, |
| 1978 |
.suspend = rt2x00usb_suspend, |
| 1979 |
.resume = rt2x00usb_resume, |
| 1980 |
.reset_resume = rt2x00usb_resume, |
| 1981 |
.disable_hub_initiated_lpm = 1, |
| 1982 |
}; |
| 1983 |
|
| 1984 |
module_usb_driver(rt2500usb_driver); |