| 1 |
/* SPDX-License-Identifier: GPL-2.0-or-later */ |
| 2 |
/* |
| 3 |
Copyright (C) 2004 - 2009 Ivo van Doorn <[email protected]> |
| 4 |
<http://rt2x00.serialmonkey.com> |
| 5 |
|
| 6 |
*/ |
| 7 |
|
| 8 |
/* |
| 9 |
Module: rt2400pci |
| 10 |
Abstract: Data structures and registers for the rt2400pci module. |
| 11 |
Supported chipsets: RT2460. |
| 12 |
*/ |
| 13 |
|
| 14 |
#ifndef RT2400PCI_H |
| 15 |
#define RT2400PCI_H |
| 16 |
|
| 17 |
/* |
| 18 |
* RF chip defines. |
| 19 |
*/ |
| 20 |
#define RF2420 0x0000 |
| 21 |
#define RF2421 0x0001 |
| 22 |
|
| 23 |
/* |
| 24 |
* Signal information. |
| 25 |
* Default offset is required for RSSI <-> dBm conversion. |
| 26 |
*/ |
| 27 |
#define DEFAULT_RSSI_OFFSET 100 |
| 28 |
|
| 29 |
/* |
| 30 |
* Register layout information. |
| 31 |
*/ |
| 32 |
#define CSR_REG_BASE 0x0000 |
| 33 |
#define CSR_REG_SIZE 0x014c |
| 34 |
#define EEPROM_BASE 0x0000 |
| 35 |
#define EEPROM_SIZE 0x0100 |
| 36 |
#define BBP_BASE 0x0000 |
| 37 |
#define BBP_SIZE 0x0020 |
| 38 |
#define RF_BASE 0x0004 |
| 39 |
#define RF_SIZE 0x000c |
| 40 |
|
| 41 |
/* |
| 42 |
* Number of TX queues. |
| 43 |
*/ |
| 44 |
#define NUM_TX_QUEUES 2 |
| 45 |
|
| 46 |
/* |
| 47 |
* Control/Status Registers(CSR). |
| 48 |
* Some values are set in TU, whereas 1 TU == 1024 us. |
| 49 |
*/ |
| 50 |
|
| 51 |
/* |
| 52 |
* CSR0: ASIC revision number. |
| 53 |
*/ |
| 54 |
#define CSR0 0x0000 |
| 55 |
#define CSR0_REVISION FIELD32(0x0000ffff) |
| 56 |
|
| 57 |
/* |
| 58 |
* CSR1: System control register. |
| 59 |
* SOFT_RESET: Software reset, 1: reset, 0: normal. |
| 60 |
* BBP_RESET: Hardware reset, 1: reset, 0, release. |
| 61 |
* HOST_READY: Host ready after initialization. |
| 62 |
*/ |
| 63 |
#define CSR1 0x0004 |
| 64 |
#define CSR1_SOFT_RESET FIELD32(0x00000001) |
| 65 |
#define CSR1_BBP_RESET FIELD32(0x00000002) |
| 66 |
#define CSR1_HOST_READY FIELD32(0x00000004) |
| 67 |
|
| 68 |
/* |
| 69 |
* CSR2: System admin status register (invalid). |
| 70 |
*/ |
| 71 |
#define CSR2 0x0008 |
| 72 |
|
| 73 |
/* |
| 74 |
* CSR3: STA MAC address register 0. |
| 75 |
*/ |
| 76 |
#define CSR3 0x000c |
| 77 |
#define CSR3_BYTE0 FIELD32(0x000000ff) |
| 78 |
#define CSR3_BYTE1 FIELD32(0x0000ff00) |
| 79 |
#define CSR3_BYTE2 FIELD32(0x00ff0000) |
| 80 |
#define CSR3_BYTE3 FIELD32(0xff000000) |
| 81 |
|
| 82 |
/* |
| 83 |
* CSR4: STA MAC address register 1. |
| 84 |
*/ |
| 85 |
#define CSR4 0x0010 |
| 86 |
#define CSR4_BYTE4 FIELD32(0x000000ff) |
| 87 |
#define CSR4_BYTE5 FIELD32(0x0000ff00) |
| 88 |
|
| 89 |
/* |
| 90 |
* CSR5: BSSID register 0. |
| 91 |
*/ |
| 92 |
#define CSR5 0x0014 |
| 93 |
#define CSR5_BYTE0 FIELD32(0x000000ff) |
| 94 |
#define CSR5_BYTE1 FIELD32(0x0000ff00) |
| 95 |
#define CSR5_BYTE2 FIELD32(0x00ff0000) |
| 96 |
#define CSR5_BYTE3 FIELD32(0xff000000) |
| 97 |
|
| 98 |
/* |
| 99 |
* CSR6: BSSID register 1. |
| 100 |
*/ |
| 101 |
#define CSR6 0x0018 |
| 102 |
#define CSR6_BYTE4 FIELD32(0x000000ff) |
| 103 |
#define CSR6_BYTE5 FIELD32(0x0000ff00) |
| 104 |
|
| 105 |
/* |
| 106 |
* CSR7: Interrupt source register. |
| 107 |
* Write 1 to clear interrupt. |
| 108 |
* TBCN_EXPIRE: Beacon timer expired interrupt. |
| 109 |
* TWAKE_EXPIRE: Wakeup timer expired interrupt. |
| 110 |
* TATIMW_EXPIRE: Timer of atim window expired interrupt. |
| 111 |
* TXDONE_TXRING: Tx ring transmit done interrupt. |
| 112 |
* TXDONE_ATIMRING: Atim ring transmit done interrupt. |
| 113 |
* TXDONE_PRIORING: Priority ring transmit done interrupt. |
| 114 |
* RXDONE: Receive done interrupt. |
| 115 |
*/ |
| 116 |
#define CSR7 0x001c |
| 117 |
#define CSR7_TBCN_EXPIRE FIELD32(0x00000001) |
| 118 |
#define CSR7_TWAKE_EXPIRE FIELD32(0x00000002) |
| 119 |
#define CSR7_TATIMW_EXPIRE FIELD32(0x00000004) |
| 120 |
#define CSR7_TXDONE_TXRING FIELD32(0x00000008) |
| 121 |
#define CSR7_TXDONE_ATIMRING FIELD32(0x00000010) |
| 122 |
#define CSR7_TXDONE_PRIORING FIELD32(0x00000020) |
| 123 |
#define CSR7_RXDONE FIELD32(0x00000040) |
| 124 |
|
| 125 |
/* |
| 126 |
* CSR8: Interrupt mask register. |
| 127 |
* Write 1 to mask interrupt. |
| 128 |
* TBCN_EXPIRE: Beacon timer expired interrupt. |
| 129 |
* TWAKE_EXPIRE: Wakeup timer expired interrupt. |
| 130 |
* TATIMW_EXPIRE: Timer of atim window expired interrupt. |
| 131 |
* TXDONE_TXRING: Tx ring transmit done interrupt. |
| 132 |
* TXDONE_ATIMRING: Atim ring transmit done interrupt. |
| 133 |
* TXDONE_PRIORING: Priority ring transmit done interrupt. |
| 134 |
* RXDONE: Receive done interrupt. |
| 135 |
*/ |
| 136 |
#define CSR8 0x0020 |
| 137 |
#define CSR8_TBCN_EXPIRE FIELD32(0x00000001) |
| 138 |
#define CSR8_TWAKE_EXPIRE FIELD32(0x00000002) |
| 139 |
#define CSR8_TATIMW_EXPIRE FIELD32(0x00000004) |
| 140 |
#define CSR8_TXDONE_TXRING FIELD32(0x00000008) |
| 141 |
#define CSR8_TXDONE_ATIMRING FIELD32(0x00000010) |
| 142 |
#define CSR8_TXDONE_PRIORING FIELD32(0x00000020) |
| 143 |
#define CSR8_RXDONE FIELD32(0x00000040) |
| 144 |
|
| 145 |
/* |
| 146 |
* CSR9: Maximum frame length register. |
| 147 |
* MAX_FRAME_UNIT: Maximum frame length in 128b unit, default: 12. |
| 148 |
*/ |
| 149 |
#define CSR9 0x0024 |
| 150 |
#define CSR9_MAX_FRAME_UNIT FIELD32(0x00000f80) |
| 151 |
|
| 152 |
/* |
| 153 |
* CSR11: Back-off control register. |
| 154 |
* CWMIN: CWmin. Default cwmin is 31 (2^5 - 1). |
| 155 |
* CWMAX: CWmax. Default cwmax is 1023 (2^10 - 1). |
| 156 |
* SLOT_TIME: Slot time, default is 20us for 802.11b. |
| 157 |
* LONG_RETRY: Long retry count. |
| 158 |
* SHORT_RETRY: Short retry count. |
| 159 |
*/ |
| 160 |
#define CSR11 0x002c |
| 161 |
#define CSR11_CWMIN FIELD32(0x0000000f) |
| 162 |
#define CSR11_CWMAX FIELD32(0x000000f0) |
| 163 |
#define CSR11_SLOT_TIME FIELD32(0x00001f00) |
| 164 |
#define CSR11_LONG_RETRY FIELD32(0x00ff0000) |
| 165 |
#define CSR11_SHORT_RETRY FIELD32(0xff000000) |
| 166 |
|
| 167 |
/* |
| 168 |
* CSR12: Synchronization configuration register 0. |
| 169 |
* All units in 1/16 TU. |
| 170 |
* BEACON_INTERVAL: Beacon interval, default is 100 TU. |
| 171 |
* CFPMAX_DURATION: Cfp maximum duration, default is 100 TU. |
| 172 |
*/ |
| 173 |
#define CSR12 0x0030 |
| 174 |
#define CSR12_BEACON_INTERVAL FIELD32(0x0000ffff) |
| 175 |
#define CSR12_CFP_MAX_DURATION FIELD32(0xffff0000) |
| 176 |
|
| 177 |
/* |
| 178 |
* CSR13: Synchronization configuration register 1. |
| 179 |
* All units in 1/16 TU. |
| 180 |
* ATIMW_DURATION: Atim window duration. |
| 181 |
* CFP_PERIOD: Cfp period, default is 0 TU. |
| 182 |
*/ |
| 183 |
#define CSR13 0x0034 |
| 184 |
#define CSR13_ATIMW_DURATION FIELD32(0x0000ffff) |
| 185 |
#define CSR13_CFP_PERIOD FIELD32(0x00ff0000) |
| 186 |
|
| 187 |
/* |
| 188 |
* CSR14: Synchronization control register. |
| 189 |
* TSF_COUNT: Enable tsf auto counting. |
| 190 |
* TSF_SYNC: Tsf sync, 0: disable, 1: infra, 2: ad-hoc/master mode. |
| 191 |
* TBCN: Enable tbcn with reload value. |
| 192 |
* TCFP: Enable tcfp & cfp / cp switching. |
| 193 |
* TATIMW: Enable tatimw & atim window switching. |
| 194 |
* BEACON_GEN: Enable beacon generator. |
| 195 |
* CFP_COUNT_PRELOAD: Cfp count preload value. |
| 196 |
* TBCM_PRELOAD: Tbcn preload value in units of 64us. |
| 197 |
*/ |
| 198 |
#define CSR14 0x0038 |
| 199 |
#define CSR14_TSF_COUNT FIELD32(0x00000001) |
| 200 |
#define CSR14_TSF_SYNC FIELD32(0x00000006) |
| 201 |
#define CSR14_TBCN FIELD32(0x00000008) |
| 202 |
#define CSR14_TCFP FIELD32(0x00000010) |
| 203 |
#define CSR14_TATIMW FIELD32(0x00000020) |
| 204 |
#define CSR14_BEACON_GEN FIELD32(0x00000040) |
| 205 |
#define CSR14_CFP_COUNT_PRELOAD FIELD32(0x0000ff00) |
| 206 |
#define CSR14_TBCM_PRELOAD FIELD32(0xffff0000) |
| 207 |
|
| 208 |
/* |
| 209 |
* CSR15: Synchronization status register. |
| 210 |
* CFP: ASIC is in contention-free period. |
| 211 |
* ATIMW: ASIC is in ATIM window. |
| 212 |
* BEACON_SENT: Beacon is send. |
| 213 |
*/ |
| 214 |
#define CSR15 0x003c |
| 215 |
#define CSR15_CFP FIELD32(0x00000001) |
| 216 |
#define CSR15_ATIMW FIELD32(0x00000002) |
| 217 |
#define CSR15_BEACON_SENT FIELD32(0x00000004) |
| 218 |
|
| 219 |
/* |
| 220 |
* CSR16: TSF timer register 0. |
| 221 |
*/ |
| 222 |
#define CSR16 0x0040 |
| 223 |
#define CSR16_LOW_TSFTIMER FIELD32(0xffffffff) |
| 224 |
|
| 225 |
/* |
| 226 |
* CSR17: TSF timer register 1. |
| 227 |
*/ |
| 228 |
#define CSR17 0x0044 |
| 229 |
#define CSR17_HIGH_TSFTIMER FIELD32(0xffffffff) |
| 230 |
|
| 231 |
/* |
| 232 |
* CSR18: IFS timer register 0. |
| 233 |
* SIFS: Sifs, default is 10 us. |
| 234 |
* PIFS: Pifs, default is 30 us. |
| 235 |
*/ |
| 236 |
#define CSR18 0x0048 |
| 237 |
#define CSR18_SIFS FIELD32(0x0000ffff) |
| 238 |
#define CSR18_PIFS FIELD32(0xffff0000) |
| 239 |
|
| 240 |
/* |
| 241 |
* CSR19: IFS timer register 1. |
| 242 |
* DIFS: Difs, default is 50 us. |
| 243 |
* EIFS: Eifs, default is 364 us. |
| 244 |
*/ |
| 245 |
#define CSR19 0x004c |
| 246 |
#define CSR19_DIFS FIELD32(0x0000ffff) |
| 247 |
#define CSR19_EIFS FIELD32(0xffff0000) |
| 248 |
|
| 249 |
/* |
| 250 |
* CSR20: Wakeup timer register. |
| 251 |
* DELAY_AFTER_TBCN: Delay after tbcn expired in units of 1/16 TU. |
| 252 |
* TBCN_BEFORE_WAKEUP: Number of beacon before wakeup. |
| 253 |
* AUTOWAKE: Enable auto wakeup / sleep mechanism. |
| 254 |
*/ |
| 255 |
#define CSR20 0x0050 |
| 256 |
#define CSR20_DELAY_AFTER_TBCN FIELD32(0x0000ffff) |
| 257 |
#define CSR20_TBCN_BEFORE_WAKEUP FIELD32(0x00ff0000) |
| 258 |
#define CSR20_AUTOWAKE FIELD32(0x01000000) |
| 259 |
|
| 260 |
/* |
| 261 |
* CSR21: EEPROM control register. |
| 262 |
* RELOAD: Write 1 to reload eeprom content. |
| 263 |
* TYPE_93C46: 1: 93c46, 0:93c66. |
| 264 |
*/ |
| 265 |
#define CSR21 0x0054 |
| 266 |
#define CSR21_RELOAD FIELD32(0x00000001) |
| 267 |
#define CSR21_EEPROM_DATA_CLOCK FIELD32(0x00000002) |
| 268 |
#define CSR21_EEPROM_CHIP_SELECT FIELD32(0x00000004) |
| 269 |
#define CSR21_EEPROM_DATA_IN FIELD32(0x00000008) |
| 270 |
#define CSR21_EEPROM_DATA_OUT FIELD32(0x00000010) |
| 271 |
#define CSR21_TYPE_93C46 FIELD32(0x00000020) |
| 272 |
|
| 273 |
/* |
| 274 |
* CSR22: CFP control register. |
| 275 |
* CFP_DURATION_REMAIN: Cfp duration remain, in units of TU. |
| 276 |
* RELOAD_CFP_DURATION: Write 1 to reload cfp duration remain. |
| 277 |
*/ |
| 278 |
#define CSR22 0x0058 |
| 279 |
#define CSR22_CFP_DURATION_REMAIN FIELD32(0x0000ffff) |
| 280 |
#define CSR22_RELOAD_CFP_DURATION FIELD32(0x00010000) |
| 281 |
|
| 282 |
/* |
| 283 |
* Transmit related CSRs. |
| 284 |
* Some values are set in TU, whereas 1 TU == 1024 us. |
| 285 |
*/ |
| 286 |
|
| 287 |
/* |
| 288 |
* TXCSR0: TX Control Register. |
| 289 |
* KICK_TX: Kick tx ring. |
| 290 |
* KICK_ATIM: Kick atim ring. |
| 291 |
* KICK_PRIO: Kick priority ring. |
| 292 |
* ABORT: Abort all transmit related ring operation. |
| 293 |
*/ |
| 294 |
#define TXCSR0 0x0060 |
| 295 |
#define TXCSR0_KICK_TX FIELD32(0x00000001) |
| 296 |
#define TXCSR0_KICK_ATIM FIELD32(0x00000002) |
| 297 |
#define TXCSR0_KICK_PRIO FIELD32(0x00000004) |
| 298 |
#define TXCSR0_ABORT FIELD32(0x00000008) |
| 299 |
|
| 300 |
/* |
| 301 |
* TXCSR1: TX Configuration Register. |
| 302 |
* ACK_TIMEOUT: Ack timeout, default = sifs + 2*slottime + acktime @ 1mbps. |
| 303 |
* ACK_CONSUME_TIME: Ack consume time, default = sifs + acktime @ 1mbps. |
| 304 |
* TSF_OFFSET: Insert tsf offset. |
| 305 |
* AUTORESPONDER: Enable auto responder which include ack & cts. |
| 306 |
*/ |
| 307 |
#define TXCSR1 0x0064 |
| 308 |
#define TXCSR1_ACK_TIMEOUT FIELD32(0x000001ff) |
| 309 |
#define TXCSR1_ACK_CONSUME_TIME FIELD32(0x0003fe00) |
| 310 |
#define TXCSR1_TSF_OFFSET FIELD32(0x00fc0000) |
| 311 |
#define TXCSR1_AUTORESPONDER FIELD32(0x01000000) |
| 312 |
|
| 313 |
/* |
| 314 |
* TXCSR2: Tx descriptor configuration register. |
| 315 |
* TXD_SIZE: Tx descriptor size, default is 48. |
| 316 |
* NUM_TXD: Number of tx entries in ring. |
| 317 |
* NUM_ATIM: Number of atim entries in ring. |
| 318 |
* NUM_PRIO: Number of priority entries in ring. |
| 319 |
*/ |
| 320 |
#define TXCSR2 0x0068 |
| 321 |
#define TXCSR2_TXD_SIZE FIELD32(0x000000ff) |
| 322 |
#define TXCSR2_NUM_TXD FIELD32(0x0000ff00) |
| 323 |
#define TXCSR2_NUM_ATIM FIELD32(0x00ff0000) |
| 324 |
#define TXCSR2_NUM_PRIO FIELD32(0xff000000) |
| 325 |
|
| 326 |
/* |
| 327 |
* TXCSR3: TX Ring Base address register. |
| 328 |
*/ |
| 329 |
#define TXCSR3 0x006c |
| 330 |
#define TXCSR3_TX_RING_REGISTER FIELD32(0xffffffff) |
| 331 |
|
| 332 |
/* |
| 333 |
* TXCSR4: TX Atim Ring Base address register. |
| 334 |
*/ |
| 335 |
#define TXCSR4 0x0070 |
| 336 |
#define TXCSR4_ATIM_RING_REGISTER FIELD32(0xffffffff) |
| 337 |
|
| 338 |
/* |
| 339 |
* TXCSR5: TX Prio Ring Base address register. |
| 340 |
*/ |
| 341 |
#define TXCSR5 0x0074 |
| 342 |
#define TXCSR5_PRIO_RING_REGISTER FIELD32(0xffffffff) |
| 343 |
|
| 344 |
/* |
| 345 |
* TXCSR6: Beacon Base address register. |
| 346 |
*/ |
| 347 |
#define TXCSR6 0x0078 |
| 348 |
#define TXCSR6_BEACON_RING_REGISTER FIELD32(0xffffffff) |
| 349 |
|
| 350 |
/* |
| 351 |
* TXCSR7: Auto responder control register. |
| 352 |
* AR_POWERMANAGEMENT: Auto responder power management bit. |
| 353 |
*/ |
| 354 |
#define TXCSR7 0x007c |
| 355 |
#define TXCSR7_AR_POWERMANAGEMENT FIELD32(0x00000001) |
| 356 |
|
| 357 |
/* |
| 358 |
* Receive related CSRs. |
| 359 |
* Some values are set in TU, whereas 1 TU == 1024 us. |
| 360 |
*/ |
| 361 |
|
| 362 |
/* |
| 363 |
* RXCSR0: RX Control Register. |
| 364 |
* DISABLE_RX: Disable rx engine. |
| 365 |
* DROP_CRC: Drop crc error. |
| 366 |
* DROP_PHYSICAL: Drop physical error. |
| 367 |
* DROP_CONTROL: Drop control frame. |
| 368 |
* DROP_NOT_TO_ME: Drop not to me unicast frame. |
| 369 |
* DROP_TODS: Drop frame tods bit is true. |
| 370 |
* DROP_VERSION_ERROR: Drop version error frame. |
| 371 |
* PASS_CRC: Pass all packets with crc attached. |
| 372 |
*/ |
| 373 |
#define RXCSR0 0x0080 |
| 374 |
#define RXCSR0_DISABLE_RX FIELD32(0x00000001) |
| 375 |
#define RXCSR0_DROP_CRC FIELD32(0x00000002) |
| 376 |
#define RXCSR0_DROP_PHYSICAL FIELD32(0x00000004) |
| 377 |
#define RXCSR0_DROP_CONTROL FIELD32(0x00000008) |
| 378 |
#define RXCSR0_DROP_NOT_TO_ME FIELD32(0x00000010) |
| 379 |
#define RXCSR0_DROP_TODS FIELD32(0x00000020) |
| 380 |
#define RXCSR0_DROP_VERSION_ERROR FIELD32(0x00000040) |
| 381 |
#define RXCSR0_PASS_CRC FIELD32(0x00000080) |
| 382 |
|
| 383 |
/* |
| 384 |
* RXCSR1: RX descriptor configuration register. |
| 385 |
* RXD_SIZE: Rx descriptor size, default is 32b. |
| 386 |
* NUM_RXD: Number of rx entries in ring. |
| 387 |
*/ |
| 388 |
#define RXCSR1 0x0084 |
| 389 |
#define RXCSR1_RXD_SIZE FIELD32(0x000000ff) |
| 390 |
#define RXCSR1_NUM_RXD FIELD32(0x0000ff00) |
| 391 |
|
| 392 |
/* |
| 393 |
* RXCSR2: RX Ring base address register. |
| 394 |
*/ |
| 395 |
#define RXCSR2 0x0088 |
| 396 |
#define RXCSR2_RX_RING_REGISTER FIELD32(0xffffffff) |
| 397 |
|
| 398 |
/* |
| 399 |
* RXCSR3: BBP ID register for Rx operation. |
| 400 |
* BBP_ID#: BBP register # id. |
| 401 |
* BBP_ID#_VALID: BBP register # id is valid or not. |
| 402 |
*/ |
| 403 |
#define RXCSR3 0x0090 |
| 404 |
#define RXCSR3_BBP_ID0 FIELD32(0x0000007f) |
| 405 |
#define RXCSR3_BBP_ID0_VALID FIELD32(0x00000080) |
| 406 |
#define RXCSR3_BBP_ID1 FIELD32(0x00007f00) |
| 407 |
#define RXCSR3_BBP_ID1_VALID FIELD32(0x00008000) |
| 408 |
#define RXCSR3_BBP_ID2 FIELD32(0x007f0000) |
| 409 |
#define RXCSR3_BBP_ID2_VALID FIELD32(0x00800000) |
| 410 |
#define RXCSR3_BBP_ID3 FIELD32(0x7f000000) |
| 411 |
#define RXCSR3_BBP_ID3_VALID FIELD32(0x80000000) |
| 412 |
|
| 413 |
/* |
| 414 |
* RXCSR4: BBP ID register for Rx operation. |
| 415 |
* BBP_ID#: BBP register # id. |
| 416 |
* BBP_ID#_VALID: BBP register # id is valid or not. |
| 417 |
*/ |
| 418 |
#define RXCSR4 0x0094 |
| 419 |
#define RXCSR4_BBP_ID4 FIELD32(0x0000007f) |
| 420 |
#define RXCSR4_BBP_ID4_VALID FIELD32(0x00000080) |
| 421 |
#define RXCSR4_BBP_ID5 FIELD32(0x00007f00) |
| 422 |
#define RXCSR4_BBP_ID5_VALID FIELD32(0x00008000) |
| 423 |
|
| 424 |
/* |
| 425 |
* ARCSR0: Auto Responder PLCP config register 0. |
| 426 |
* ARCSR0_AR_BBP_DATA#: Auto responder BBP register # data. |
| 427 |
* ARCSR0_AR_BBP_ID#: Auto responder BBP register # Id. |
| 428 |
*/ |
| 429 |
#define ARCSR0 0x0098 |
| 430 |
#define ARCSR0_AR_BBP_DATA0 FIELD32(0x000000ff) |
| 431 |
#define ARCSR0_AR_BBP_ID0 FIELD32(0x0000ff00) |
| 432 |
#define ARCSR0_AR_BBP_DATA1 FIELD32(0x00ff0000) |
| 433 |
#define ARCSR0_AR_BBP_ID1 FIELD32(0xff000000) |
| 434 |
|
| 435 |
/* |
| 436 |
* ARCSR1: Auto Responder PLCP config register 1. |
| 437 |
* ARCSR0_AR_BBP_DATA#: Auto responder BBP register # data. |
| 438 |
* ARCSR0_AR_BBP_ID#: Auto responder BBP register # Id. |
| 439 |
*/ |
| 440 |
#define ARCSR1 0x009c |
| 441 |
#define ARCSR1_AR_BBP_DATA2 FIELD32(0x000000ff) |
| 442 |
#define ARCSR1_AR_BBP_ID2 FIELD32(0x0000ff00) |
| 443 |
#define ARCSR1_AR_BBP_DATA3 FIELD32(0x00ff0000) |
| 444 |
#define ARCSR1_AR_BBP_ID3 FIELD32(0xff000000) |
| 445 |
|
| 446 |
/* |
| 447 |
* Miscellaneous Registers. |
| 448 |
* Some values are set in TU, whereas 1 TU == 1024 us. |
| 449 |
*/ |
| 450 |
|
| 451 |
/* |
| 452 |
* PCICSR: PCI control register. |
| 453 |
* BIG_ENDIAN: 1: big endian, 0: little endian. |
| 454 |
* RX_TRESHOLD: Rx threshold in dw to start pci access |
| 455 |
* 0: 16dw (default), 1: 8dw, 2: 4dw, 3: 32dw. |
| 456 |
* TX_TRESHOLD: Tx threshold in dw to start pci access |
| 457 |
* 0: 0dw (default), 1: 1dw, 2: 4dw, 3: forward. |
| 458 |
* BURST_LENTH: Pci burst length 0: 4dw (default, 1: 8dw, 2: 16dw, 3:32dw. |
| 459 |
* ENABLE_CLK: Enable clk_run, pci clock can't going down to non-operational. |
| 460 |
*/ |
| 461 |
#define PCICSR 0x008c |
| 462 |
#define PCICSR_BIG_ENDIAN FIELD32(0x00000001) |
| 463 |
#define PCICSR_RX_TRESHOLD FIELD32(0x00000006) |
| 464 |
#define PCICSR_TX_TRESHOLD FIELD32(0x00000018) |
| 465 |
#define PCICSR_BURST_LENTH FIELD32(0x00000060) |
| 466 |
#define PCICSR_ENABLE_CLK FIELD32(0x00000080) |
| 467 |
|
| 468 |
/* |
| 469 |
* CNT0: FCS error count. |
| 470 |
* FCS_ERROR: FCS error count, cleared when read. |
| 471 |
*/ |
| 472 |
#define CNT0 0x00a0 |
| 473 |
#define CNT0_FCS_ERROR FIELD32(0x0000ffff) |
| 474 |
|
| 475 |
/* |
| 476 |
* Statistic Register. |
| 477 |
* CNT1: PLCP error count. |
| 478 |
* CNT2: Long error count. |
| 479 |
* CNT3: CCA false alarm count. |
| 480 |
* CNT4: Rx FIFO overflow count. |
| 481 |
* CNT5: Tx FIFO underrun count. |
| 482 |
*/ |
| 483 |
#define TIMECSR2 0x00a8 |
| 484 |
#define CNT1 0x00ac |
| 485 |
#define CNT2 0x00b0 |
| 486 |
#define TIMECSR3 0x00b4 |
| 487 |
#define CNT3 0x00b8 |
| 488 |
#define CNT4 0x00bc |
| 489 |
#define CNT5 0x00c0 |
| 490 |
|
| 491 |
/* |
| 492 |
* Baseband Control Register. |
| 493 |
*/ |
| 494 |
|
| 495 |
/* |
| 496 |
* PWRCSR0: Power mode configuration register. |
| 497 |
*/ |
| 498 |
#define PWRCSR0 0x00c4 |
| 499 |
|
| 500 |
/* |
| 501 |
* Power state transition time registers. |
| 502 |
*/ |
| 503 |
#define PSCSR0 0x00c8 |
| 504 |
#define PSCSR1 0x00cc |
| 505 |
#define PSCSR2 0x00d0 |
| 506 |
#define PSCSR3 0x00d4 |
| 507 |
|
| 508 |
/* |
| 509 |
* PWRCSR1: Manual power control / status register. |
| 510 |
* Allowed state: 0 deep_sleep, 1: sleep, 2: standby, 3: awake. |
| 511 |
* SET_STATE: Set state. Write 1 to trigger, self cleared. |
| 512 |
* BBP_DESIRE_STATE: BBP desired state. |
| 513 |
* RF_DESIRE_STATE: RF desired state. |
| 514 |
* BBP_CURR_STATE: BBP current state. |
| 515 |
* RF_CURR_STATE: RF current state. |
| 516 |
* PUT_TO_SLEEP: Put to sleep. Write 1 to trigger, self cleared. |
| 517 |
*/ |
| 518 |
#define PWRCSR1 0x00d8 |
| 519 |
#define PWRCSR1_SET_STATE FIELD32(0x00000001) |
| 520 |
#define PWRCSR1_BBP_DESIRE_STATE FIELD32(0x00000006) |
| 521 |
#define PWRCSR1_RF_DESIRE_STATE FIELD32(0x00000018) |
| 522 |
#define PWRCSR1_BBP_CURR_STATE FIELD32(0x00000060) |
| 523 |
#define PWRCSR1_RF_CURR_STATE FIELD32(0x00000180) |
| 524 |
#define PWRCSR1_PUT_TO_SLEEP FIELD32(0x00000200) |
| 525 |
|
| 526 |
/* |
| 527 |
* TIMECSR: Timer control register. |
| 528 |
* US_COUNT: 1 us timer count in units of clock cycles. |
| 529 |
* US_64_COUNT: 64 us timer count in units of 1 us timer. |
| 530 |
* BEACON_EXPECT: Beacon expect window. |
| 531 |
*/ |
| 532 |
#define TIMECSR 0x00dc |
| 533 |
#define TIMECSR_US_COUNT FIELD32(0x000000ff) |
| 534 |
#define TIMECSR_US_64_COUNT FIELD32(0x0000ff00) |
| 535 |
#define TIMECSR_BEACON_EXPECT FIELD32(0x00070000) |
| 536 |
|
| 537 |
/* |
| 538 |
* MACCSR0: MAC configuration register 0. |
| 539 |
*/ |
| 540 |
#define MACCSR0 0x00e0 |
| 541 |
|
| 542 |
/* |
| 543 |
* MACCSR1: MAC configuration register 1. |
| 544 |
* KICK_RX: Kick one-shot rx in one-shot rx mode. |
| 545 |
* ONESHOT_RXMODE: Enable one-shot rx mode for debugging. |
| 546 |
* BBPRX_RESET_MODE: Ralink bbp rx reset mode. |
| 547 |
* AUTO_TXBBP: Auto tx logic access bbp control register. |
| 548 |
* AUTO_RXBBP: Auto rx logic access bbp control register. |
| 549 |
* LOOPBACK: Loopback mode. 0: normal, 1: internal, 2: external, 3:rsvd. |
| 550 |
* INTERSIL_IF: Intersil if calibration pin. |
| 551 |
*/ |
| 552 |
#define MACCSR1 0x00e4 |
| 553 |
#define MACCSR1_KICK_RX FIELD32(0x00000001) |
| 554 |
#define MACCSR1_ONESHOT_RXMODE FIELD32(0x00000002) |
| 555 |
#define MACCSR1_BBPRX_RESET_MODE FIELD32(0x00000004) |
| 556 |
#define MACCSR1_AUTO_TXBBP FIELD32(0x00000008) |
| 557 |
#define MACCSR1_AUTO_RXBBP FIELD32(0x00000010) |
| 558 |
#define MACCSR1_LOOPBACK FIELD32(0x00000060) |
| 559 |
#define MACCSR1_INTERSIL_IF FIELD32(0x00000080) |
| 560 |
|
| 561 |
/* |
| 562 |
* RALINKCSR: Ralink Rx auto-reset BBCR. |
| 563 |
* AR_BBP_DATA#: Auto reset BBP register # data. |
| 564 |
* AR_BBP_ID#: Auto reset BBP register # id. |
| 565 |
*/ |
| 566 |
#define RALINKCSR 0x00e8 |
| 567 |
#define RALINKCSR_AR_BBP_DATA0 FIELD32(0x000000ff) |
| 568 |
#define RALINKCSR_AR_BBP_ID0 FIELD32(0x0000ff00) |
| 569 |
#define RALINKCSR_AR_BBP_DATA1 FIELD32(0x00ff0000) |
| 570 |
#define RALINKCSR_AR_BBP_ID1 FIELD32(0xff000000) |
| 571 |
|
| 572 |
/* |
| 573 |
* BCNCSR: Beacon interval control register. |
| 574 |
* CHANGE: Write one to change beacon interval. |
| 575 |
* DELTATIME: The delta time value. |
| 576 |
* NUM_BEACON: Number of beacon according to mode. |
| 577 |
* MODE: Please refer to asic specs. |
| 578 |
* PLUS: Plus or minus delta time value. |
| 579 |
*/ |
| 580 |
#define BCNCSR 0x00ec |
| 581 |
#define BCNCSR_CHANGE FIELD32(0x00000001) |
| 582 |
#define BCNCSR_DELTATIME FIELD32(0x0000001e) |
| 583 |
#define BCNCSR_NUM_BEACON FIELD32(0x00001fe0) |
| 584 |
#define BCNCSR_MODE FIELD32(0x00006000) |
| 585 |
#define BCNCSR_PLUS FIELD32(0x00008000) |
| 586 |
|
| 587 |
/* |
| 588 |
* BBP / RF / IF Control Register. |
| 589 |
*/ |
| 590 |
|
| 591 |
/* |
| 592 |
* BBPCSR: BBP serial control register. |
| 593 |
* VALUE: Register value to program into BBP. |
| 594 |
* REGNUM: Selected BBP register. |
| 595 |
* BUSY: 1: asic is busy execute BBP programming. |
| 596 |
* WRITE_CONTROL: 1: write BBP, 0: read BBP. |
| 597 |
*/ |
| 598 |
#define BBPCSR 0x00f0 |
| 599 |
#define BBPCSR_VALUE FIELD32(0x000000ff) |
| 600 |
#define BBPCSR_REGNUM FIELD32(0x00007f00) |
| 601 |
#define BBPCSR_BUSY FIELD32(0x00008000) |
| 602 |
#define BBPCSR_WRITE_CONTROL FIELD32(0x00010000) |
| 603 |
|
| 604 |
/* |
| 605 |
* RFCSR: RF serial control register. |
| 606 |
* VALUE: Register value + id to program into rf/if. |
| 607 |
* NUMBER_OF_BITS: Number of bits used in value (i:20, rfmd:22). |
| 608 |
* IF_SELECT: Chip to program: 0: rf, 1: if. |
| 609 |
* PLL_LD: Rf pll_ld status. |
| 610 |
* BUSY: 1: asic is busy execute rf programming. |
| 611 |
*/ |
| 612 |
#define RFCSR 0x00f4 |
| 613 |
#define RFCSR_VALUE FIELD32(0x00ffffff) |
| 614 |
#define RFCSR_NUMBER_OF_BITS FIELD32(0x1f000000) |
| 615 |
#define RFCSR_IF_SELECT FIELD32(0x20000000) |
| 616 |
#define RFCSR_PLL_LD FIELD32(0x40000000) |
| 617 |
#define RFCSR_BUSY FIELD32(0x80000000) |
| 618 |
|
| 619 |
/* |
| 620 |
* LEDCSR: LED control register. |
| 621 |
* ON_PERIOD: On period, default 70ms. |
| 622 |
* OFF_PERIOD: Off period, default 30ms. |
| 623 |
* LINK: 0: linkoff, 1: linkup. |
| 624 |
* ACTIVITY: 0: idle, 1: active. |
| 625 |
*/ |
| 626 |
#define LEDCSR 0x00f8 |
| 627 |
#define LEDCSR_ON_PERIOD FIELD32(0x000000ff) |
| 628 |
#define LEDCSR_OFF_PERIOD FIELD32(0x0000ff00) |
| 629 |
#define LEDCSR_LINK FIELD32(0x00010000) |
| 630 |
#define LEDCSR_ACTIVITY FIELD32(0x00020000) |
| 631 |
|
| 632 |
/* |
| 633 |
* ASIC pointer information. |
| 634 |
* RXPTR: Current RX ring address. |
| 635 |
* TXPTR: Current Tx ring address. |
| 636 |
* PRIPTR: Current Priority ring address. |
| 637 |
* ATIMPTR: Current ATIM ring address. |
| 638 |
*/ |
| 639 |
#define RXPTR 0x0100 |
| 640 |
#define TXPTR 0x0104 |
| 641 |
#define PRIPTR 0x0108 |
| 642 |
#define ATIMPTR 0x010c |
| 643 |
|
| 644 |
/* |
| 645 |
* GPIO and others. |
| 646 |
*/ |
| 647 |
|
| 648 |
/* |
| 649 |
* GPIOCSR: GPIO control register. |
| 650 |
* GPIOCSR_VALx: Actual GPIO pin x value |
| 651 |
* GPIOCSR_DIRx: GPIO direction: 0 = output; 1 = input |
| 652 |
*/ |
| 653 |
#define GPIOCSR 0x0120 |
| 654 |
#define GPIOCSR_VAL0 FIELD32(0x00000001) |
| 655 |
#define GPIOCSR_VAL1 FIELD32(0x00000002) |
| 656 |
#define GPIOCSR_VAL2 FIELD32(0x00000004) |
| 657 |
#define GPIOCSR_VAL3 FIELD32(0x00000008) |
| 658 |
#define GPIOCSR_VAL4 FIELD32(0x00000010) |
| 659 |
#define GPIOCSR_VAL5 FIELD32(0x00000020) |
| 660 |
#define GPIOCSR_VAL6 FIELD32(0x00000040) |
| 661 |
#define GPIOCSR_VAL7 FIELD32(0x00000080) |
| 662 |
#define GPIOCSR_DIR0 FIELD32(0x00000100) |
| 663 |
#define GPIOCSR_DIR1 FIELD32(0x00000200) |
| 664 |
#define GPIOCSR_DIR2 FIELD32(0x00000400) |
| 665 |
#define GPIOCSR_DIR3 FIELD32(0x00000800) |
| 666 |
#define GPIOCSR_DIR4 FIELD32(0x00001000) |
| 667 |
#define GPIOCSR_DIR5 FIELD32(0x00002000) |
| 668 |
#define GPIOCSR_DIR6 FIELD32(0x00004000) |
| 669 |
#define GPIOCSR_DIR7 FIELD32(0x00008000) |
| 670 |
|
| 671 |
/* |
| 672 |
* BBPPCSR: BBP Pin control register. |
| 673 |
*/ |
| 674 |
#define BBPPCSR 0x0124 |
| 675 |
|
| 676 |
/* |
| 677 |
* BCNCSR1: Tx BEACON offset time control register. |
| 678 |
* PRELOAD: Beacon timer offset in units of usec. |
| 679 |
*/ |
| 680 |
#define BCNCSR1 0x0130 |
| 681 |
#define BCNCSR1_PRELOAD FIELD32(0x0000ffff) |
| 682 |
|
| 683 |
/* |
| 684 |
* MACCSR2: TX_PE to RX_PE turn-around time control register |
| 685 |
* DELAY: RX_PE low width, in units of pci clock cycle. |
| 686 |
*/ |
| 687 |
#define MACCSR2 0x0134 |
| 688 |
#define MACCSR2_DELAY FIELD32(0x000000ff) |
| 689 |
|
| 690 |
/* |
| 691 |
* ARCSR2: 1 Mbps ACK/CTS PLCP. |
| 692 |
*/ |
| 693 |
#define ARCSR2 0x013c |
| 694 |
#define ARCSR2_SIGNAL FIELD32(0x000000ff) |
| 695 |
#define ARCSR2_SERVICE FIELD32(0x0000ff00) |
| 696 |
#define ARCSR2_LENGTH_LOW FIELD32(0x00ff0000) |
| 697 |
#define ARCSR2_LENGTH FIELD32(0xffff0000) |
| 698 |
|
| 699 |
/* |
| 700 |
* ARCSR3: 2 Mbps ACK/CTS PLCP. |
| 701 |
*/ |
| 702 |
#define ARCSR3 0x0140 |
| 703 |
#define ARCSR3_SIGNAL FIELD32(0x000000ff) |
| 704 |
#define ARCSR3_SERVICE FIELD32(0x0000ff00) |
| 705 |
#define ARCSR3_LENGTH FIELD32(0xffff0000) |
| 706 |
|
| 707 |
/* |
| 708 |
* ARCSR4: 5.5 Mbps ACK/CTS PLCP. |
| 709 |
*/ |
| 710 |
#define ARCSR4 0x0144 |
| 711 |
#define ARCSR4_SIGNAL FIELD32(0x000000ff) |
| 712 |
#define ARCSR4_SERVICE FIELD32(0x0000ff00) |
| 713 |
#define ARCSR4_LENGTH FIELD32(0xffff0000) |
| 714 |
|
| 715 |
/* |
| 716 |
* ARCSR5: 11 Mbps ACK/CTS PLCP. |
| 717 |
*/ |
| 718 |
#define ARCSR5 0x0148 |
| 719 |
#define ARCSR5_SIGNAL FIELD32(0x000000ff) |
| 720 |
#define ARCSR5_SERVICE FIELD32(0x0000ff00) |
| 721 |
#define ARCSR5_LENGTH FIELD32(0xffff0000) |
| 722 |
|
| 723 |
/* |
| 724 |
* BBP registers. |
| 725 |
* The wordsize of the BBP is 8 bits. |
| 726 |
*/ |
| 727 |
|
| 728 |
/* |
| 729 |
* R1: TX antenna control |
| 730 |
*/ |
| 731 |
#define BBP_R1_TX_ANTENNA FIELD8(0x03) |
| 732 |
|
| 733 |
/* |
| 734 |
* R4: RX antenna control |
| 735 |
*/ |
| 736 |
#define BBP_R4_RX_ANTENNA FIELD8(0x06) |
| 737 |
|
| 738 |
/* |
| 739 |
* RF registers |
| 740 |
*/ |
| 741 |
|
| 742 |
/* |
| 743 |
* RF 1 |
| 744 |
*/ |
| 745 |
#define RF1_TUNER FIELD32(0x00020000) |
| 746 |
|
| 747 |
/* |
| 748 |
* RF 3 |
| 749 |
*/ |
| 750 |
#define RF3_TUNER FIELD32(0x00000100) |
| 751 |
#define RF3_TXPOWER FIELD32(0x00003e00) |
| 752 |
|
| 753 |
/* |
| 754 |
* EEPROM content. |
| 755 |
* The wordsize of the EEPROM is 16 bits. |
| 756 |
*/ |
| 757 |
|
| 758 |
/* |
| 759 |
* HW MAC address. |
| 760 |
*/ |
| 761 |
#define EEPROM_MAC_ADDR_0 0x0002 |
| 762 |
#define EEPROM_MAC_ADDR_BYTE0 FIELD16(0x00ff) |
| 763 |
#define EEPROM_MAC_ADDR_BYTE1 FIELD16(0xff00) |
| 764 |
#define EEPROM_MAC_ADDR1 0x0003 |
| 765 |
#define EEPROM_MAC_ADDR_BYTE2 FIELD16(0x00ff) |
| 766 |
#define EEPROM_MAC_ADDR_BYTE3 FIELD16(0xff00) |
| 767 |
#define EEPROM_MAC_ADDR_2 0x0004 |
| 768 |
#define EEPROM_MAC_ADDR_BYTE4 FIELD16(0x00ff) |
| 769 |
#define EEPROM_MAC_ADDR_BYTE5 FIELD16(0xff00) |
| 770 |
|
| 771 |
/* |
| 772 |
* EEPROM antenna. |
| 773 |
* ANTENNA_NUM: Number of antenna's. |
| 774 |
* TX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B. |
| 775 |
* RX_DEFAULT: Default antenna 0: diversity, 1: A, 2: B. |
| 776 |
* RF_TYPE: Rf_type of this adapter. |
| 777 |
* LED_MODE: 0: default, 1: TX/RX activity,2: Single (ignore link), 3: rsvd. |
| 778 |
* RX_AGCVGC: 0: disable, 1:enable BBP R13 tuning. |
| 779 |
* HARDWARE_RADIO: 1: Hardware controlled radio. Read GPIO0. |
| 780 |
*/ |
| 781 |
#define EEPROM_ANTENNA 0x0b |
| 782 |
#define EEPROM_ANTENNA_NUM FIELD16(0x0003) |
| 783 |
#define EEPROM_ANTENNA_TX_DEFAULT FIELD16(0x000c) |
| 784 |
#define EEPROM_ANTENNA_RX_DEFAULT FIELD16(0x0030) |
| 785 |
#define EEPROM_ANTENNA_RF_TYPE FIELD16(0x0040) |
| 786 |
#define EEPROM_ANTENNA_LED_MODE FIELD16(0x0180) |
| 787 |
#define EEPROM_ANTENNA_RX_AGCVGC_TUNING FIELD16(0x0200) |
| 788 |
#define EEPROM_ANTENNA_HARDWARE_RADIO FIELD16(0x0400) |
| 789 |
|
| 790 |
/* |
| 791 |
* EEPROM BBP. |
| 792 |
*/ |
| 793 |
#define EEPROM_BBP_START 0x0c |
| 794 |
#define EEPROM_BBP_SIZE 7 |
| 795 |
#define EEPROM_BBP_VALUE FIELD16(0x00ff) |
| 796 |
#define EEPROM_BBP_REG_ID FIELD16(0xff00) |
| 797 |
|
| 798 |
/* |
| 799 |
* EEPROM TXPOWER |
| 800 |
*/ |
| 801 |
#define EEPROM_TXPOWER_START 0x13 |
| 802 |
#define EEPROM_TXPOWER_SIZE 7 |
| 803 |
#define EEPROM_TXPOWER_1 FIELD16(0x00ff) |
| 804 |
#define EEPROM_TXPOWER_2 FIELD16(0xff00) |
| 805 |
|
| 806 |
/* |
| 807 |
* DMA descriptor defines. |
| 808 |
*/ |
| 809 |
#define TXD_DESC_SIZE (8 * sizeof(__le32)) |
| 810 |
#define RXD_DESC_SIZE (8 * sizeof(__le32)) |
| 811 |
|
| 812 |
/* |
| 813 |
* TX descriptor format for TX, PRIO, ATIM and Beacon Ring. |
| 814 |
*/ |
| 815 |
|
| 816 |
/* |
| 817 |
* Word0 |
| 818 |
*/ |
| 819 |
#define TXD_W0_OWNER_NIC FIELD32(0x00000001) |
| 820 |
#define TXD_W0_VALID FIELD32(0x00000002) |
| 821 |
#define TXD_W0_RESULT FIELD32(0x0000001c) |
| 822 |
#define TXD_W0_RETRY_COUNT FIELD32(0x000000e0) |
| 823 |
#define TXD_W0_MORE_FRAG FIELD32(0x00000100) |
| 824 |
#define TXD_W0_ACK FIELD32(0x00000200) |
| 825 |
#define TXD_W0_TIMESTAMP FIELD32(0x00000400) |
| 826 |
#define TXD_W0_RTS FIELD32(0x00000800) |
| 827 |
#define TXD_W0_IFS FIELD32(0x00006000) |
| 828 |
#define TXD_W0_RETRY_MODE FIELD32(0x00008000) |
| 829 |
#define TXD_W0_AGC FIELD32(0x00ff0000) |
| 830 |
#define TXD_W0_R2 FIELD32(0xff000000) |
| 831 |
|
| 832 |
/* |
| 833 |
* Word1 |
| 834 |
*/ |
| 835 |
#define TXD_W1_BUFFER_ADDRESS FIELD32(0xffffffff) |
| 836 |
|
| 837 |
/* |
| 838 |
* Word2 |
| 839 |
*/ |
| 840 |
#define TXD_W2_BUFFER_LENGTH FIELD32(0x0000ffff) |
| 841 |
#define TXD_W2_DATABYTE_COUNT FIELD32(0xffff0000) |
| 842 |
|
| 843 |
/* |
| 844 |
* Word3 & 4: PLCP information |
| 845 |
* The PLCP values should be treated as if they were BBP values. |
| 846 |
*/ |
| 847 |
#define TXD_W3_PLCP_SIGNAL FIELD32(0x000000ff) |
| 848 |
#define TXD_W3_PLCP_SIGNAL_REGNUM FIELD32(0x00007f00) |
| 849 |
#define TXD_W3_PLCP_SIGNAL_BUSY FIELD32(0x00008000) |
| 850 |
#define TXD_W3_PLCP_SERVICE FIELD32(0x00ff0000) |
| 851 |
#define TXD_W3_PLCP_SERVICE_REGNUM FIELD32(0x7f000000) |
| 852 |
#define TXD_W3_PLCP_SERVICE_BUSY FIELD32(0x80000000) |
| 853 |
|
| 854 |
#define TXD_W4_PLCP_LENGTH_LOW FIELD32(0x000000ff) |
| 855 |
#define TXD_W3_PLCP_LENGTH_LOW_REGNUM FIELD32(0x00007f00) |
| 856 |
#define TXD_W3_PLCP_LENGTH_LOW_BUSY FIELD32(0x00008000) |
| 857 |
#define TXD_W4_PLCP_LENGTH_HIGH FIELD32(0x00ff0000) |
| 858 |
#define TXD_W3_PLCP_LENGTH_HIGH_REGNUM FIELD32(0x7f000000) |
| 859 |
#define TXD_W3_PLCP_LENGTH_HIGH_BUSY FIELD32(0x80000000) |
| 860 |
|
| 861 |
/* |
| 862 |
* Word5 |
| 863 |
*/ |
| 864 |
#define TXD_W5_BBCR4 FIELD32(0x0000ffff) |
| 865 |
#define TXD_W5_AGC_REG FIELD32(0x007f0000) |
| 866 |
#define TXD_W5_AGC_REG_VALID FIELD32(0x00800000) |
| 867 |
#define TXD_W5_XXX_REG FIELD32(0x7f000000) |
| 868 |
#define TXD_W5_XXX_REG_VALID FIELD32(0x80000000) |
| 869 |
|
| 870 |
/* |
| 871 |
* Word6 |
| 872 |
*/ |
| 873 |
#define TXD_W6_SK_BUFF FIELD32(0xffffffff) |
| 874 |
|
| 875 |
/* |
| 876 |
* Word7 |
| 877 |
*/ |
| 878 |
#define TXD_W7_RESERVED FIELD32(0xffffffff) |
| 879 |
|
| 880 |
/* |
| 881 |
* RX descriptor format for RX Ring. |
| 882 |
*/ |
| 883 |
|
| 884 |
/* |
| 885 |
* Word0 |
| 886 |
*/ |
| 887 |
#define RXD_W0_OWNER_NIC FIELD32(0x00000001) |
| 888 |
#define RXD_W0_UNICAST_TO_ME FIELD32(0x00000002) |
| 889 |
#define RXD_W0_MULTICAST FIELD32(0x00000004) |
| 890 |
#define RXD_W0_BROADCAST FIELD32(0x00000008) |
| 891 |
#define RXD_W0_MY_BSS FIELD32(0x00000010) |
| 892 |
#define RXD_W0_CRC_ERROR FIELD32(0x00000020) |
| 893 |
#define RXD_W0_PHYSICAL_ERROR FIELD32(0x00000080) |
| 894 |
#define RXD_W0_DATABYTE_COUNT FIELD32(0xffff0000) |
| 895 |
|
| 896 |
/* |
| 897 |
* Word1 |
| 898 |
*/ |
| 899 |
#define RXD_W1_BUFFER_ADDRESS FIELD32(0xffffffff) |
| 900 |
|
| 901 |
/* |
| 902 |
* Word2 |
| 903 |
*/ |
| 904 |
#define RXD_W2_BUFFER_LENGTH FIELD32(0x0000ffff) |
| 905 |
#define RXD_W2_BBR0 FIELD32(0x00ff0000) |
| 906 |
#define RXD_W2_SIGNAL FIELD32(0xff000000) |
| 907 |
|
| 908 |
/* |
| 909 |
* Word3 |
| 910 |
*/ |
| 911 |
#define RXD_W3_RSSI FIELD32(0x000000ff) |
| 912 |
#define RXD_W3_BBR3 FIELD32(0x0000ff00) |
| 913 |
#define RXD_W3_BBR4 FIELD32(0x00ff0000) |
| 914 |
#define RXD_W3_BBR5 FIELD32(0xff000000) |
| 915 |
|
| 916 |
/* |
| 917 |
* Word4 |
| 918 |
*/ |
| 919 |
#define RXD_W4_RX_END_TIME FIELD32(0xffffffff) |
| 920 |
|
| 921 |
/* |
| 922 |
* Word5 & 6 & 7: Reserved |
| 923 |
*/ |
| 924 |
#define RXD_W5_RESERVED FIELD32(0xffffffff) |
| 925 |
#define RXD_W6_RESERVED FIELD32(0xffffffff) |
| 926 |
#define RXD_W7_RESERVED FIELD32(0xffffffff) |
| 927 |
|
| 928 |
/* |
| 929 |
* Macros for converting txpower from EEPROM to mac80211 value |
| 930 |
* and from mac80211 value to register value. |
| 931 |
* NOTE: Logics in rt2400pci for txpower are reversed |
| 932 |
* compared to the other rt2x00 drivers. A higher txpower |
| 933 |
* value means that the txpower must be lowered. This is |
| 934 |
* important when converting the value coming from the |
| 935 |
* mac80211 stack to the rt2400 acceptable value. |
| 936 |
*/ |
| 937 |
#define MIN_TXPOWER 31 |
| 938 |
#define MAX_TXPOWER 62 |
| 939 |
#define DEFAULT_TXPOWER 39 |
| 940 |
|
| 941 |
#define __CLAMP_TX(__txpower) \ |
| 942 |
clamp_t(u8, (__txpower), MIN_TXPOWER, MAX_TXPOWER) |
| 943 |
|
| 944 |
#define TXPOWER_FROM_DEV(__txpower) \ |
| 945 |
((__CLAMP_TX(__txpower) - MAX_TXPOWER) + MIN_TXPOWER) |
| 946 |
|
| 947 |
#define TXPOWER_TO_DEV(__txpower) \ |
| 948 |
(MAX_TXPOWER - (__CLAMP_TX(__txpower) - MIN_TXPOWER)) |
| 949 |
|
| 950 |
#endif /* RT2400PCI_H */ |