| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
|
| 4 |
Broadcom B43 wireless driver |
| 5 |
|
| 6 |
Copyright (c) 2005 Martin Langer <[email protected]> |
| 7 |
Copyright (c) 2005 Stefano Brivio <[email protected]> |
| 8 |
Copyright (c) 2005-2009 Michael Buesch <[email protected]> |
| 9 |
Copyright (c) 2005 Danny van Dyk <[email protected]> |
| 10 |
Copyright (c) 2005 Andreas Jaggi <[email protected]> |
| 11 |
Copyright (c) 2010-2011 Rafał Miłecki <[email protected]> |
| 12 |
|
| 13 |
SDIO support |
| 14 |
Copyright (c) 2009 Albert Herranz <[email protected]> |
| 15 |
|
| 16 |
Some parts of the code in this file are derived from the ipw2200 |
| 17 |
driver Copyright(c) 2003 - 2004 Intel Corporation. |
| 18 |
|
| 19 |
|
| 20 |
*/ |
| 21 |
|
| 22 |
#include <linux/delay.h> |
| 23 |
#include <linux/init.h> |
| 24 |
#include <linux/module.h> |
| 25 |
#include <linux/if_arp.h> |
| 26 |
#include <linux/etherdevice.h> |
| 27 |
#include <linux/firmware.h> |
| 28 |
#include <linux/workqueue.h> |
| 29 |
#include <linux/skbuff.h> |
| 30 |
#include <linux/io.h> |
| 31 |
#include <linux/dma-mapping.h> |
| 32 |
#include <linux/slab.h> |
| 33 |
#include <linux/unaligned.h> |
| 34 |
|
| 35 |
#include "b43.h" |
| 36 |
#include "main.h" |
| 37 |
#include "debugfs.h" |
| 38 |
#include "phy_common.h" |
| 39 |
#include "phy_g.h" |
| 40 |
#include "phy_n.h" |
| 41 |
#include "dma.h" |
| 42 |
#include "pio.h" |
| 43 |
#include "sysfs.h" |
| 44 |
#include "xmit.h" |
| 45 |
#include "lo.h" |
| 46 |
#include "sdio.h" |
| 47 |
#include <linux/mmc/sdio_func.h> |
| 48 |
|
| 49 |
MODULE_DESCRIPTION("Broadcom B43 wireless driver"); |
| 50 |
MODULE_AUTHOR("Martin Langer"); |
| 51 |
MODULE_AUTHOR("Stefano Brivio"); |
| 52 |
MODULE_AUTHOR("Michael Buesch"); |
| 53 |
MODULE_AUTHOR("Gábor Stefanik"); |
| 54 |
MODULE_AUTHOR("Rafał Miłecki"); |
| 55 |
MODULE_LICENSE("GPL"); |
| 56 |
|
| 57 |
MODULE_FIRMWARE("b43/ucode11.fw"); |
| 58 |
MODULE_FIRMWARE("b43/ucode13.fw"); |
| 59 |
MODULE_FIRMWARE("b43/ucode14.fw"); |
| 60 |
MODULE_FIRMWARE("b43/ucode15.fw"); |
| 61 |
MODULE_FIRMWARE("b43/ucode16_lp.fw"); |
| 62 |
MODULE_FIRMWARE("b43/ucode16_mimo.fw"); |
| 63 |
MODULE_FIRMWARE("b43/ucode24_lcn.fw"); |
| 64 |
MODULE_FIRMWARE("b43/ucode25_lcn.fw"); |
| 65 |
MODULE_FIRMWARE("b43/ucode25_mimo.fw"); |
| 66 |
MODULE_FIRMWARE("b43/ucode26_mimo.fw"); |
| 67 |
MODULE_FIRMWARE("b43/ucode29_mimo.fw"); |
| 68 |
MODULE_FIRMWARE("b43/ucode33_lcn40.fw"); |
| 69 |
MODULE_FIRMWARE("b43/ucode30_mimo.fw"); |
| 70 |
MODULE_FIRMWARE("b43/ucode5.fw"); |
| 71 |
MODULE_FIRMWARE("b43/ucode40.fw"); |
| 72 |
MODULE_FIRMWARE("b43/ucode42.fw"); |
| 73 |
MODULE_FIRMWARE("b43/ucode9.fw"); |
| 74 |
|
| 75 |
static int modparam_bad_frames_preempt; |
| 76 |
module_param_named(bad_frames_preempt, modparam_bad_frames_preempt, int, 0444); |
| 77 |
MODULE_PARM_DESC(bad_frames_preempt, |
| 78 |
"enable(1) / disable(0) Bad Frames Preemption"); |
| 79 |
|
| 80 |
static char modparam_fwpostfix[16]; |
| 81 |
module_param_string(fwpostfix, modparam_fwpostfix, 16, 0444); |
| 82 |
MODULE_PARM_DESC(fwpostfix, "Postfix for the .fw files to load."); |
| 83 |
|
| 84 |
static int modparam_hwpctl; |
| 85 |
module_param_named(hwpctl, modparam_hwpctl, int, 0444); |
| 86 |
MODULE_PARM_DESC(hwpctl, "Enable hardware-side power control (default off)"); |
| 87 |
|
| 88 |
static int modparam_nohwcrypt; |
| 89 |
module_param_named(nohwcrypt, modparam_nohwcrypt, int, 0444); |
| 90 |
MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); |
| 91 |
|
| 92 |
static int modparam_hwtkip; |
| 93 |
module_param_named(hwtkip, modparam_hwtkip, int, 0444); |
| 94 |
MODULE_PARM_DESC(hwtkip, "Enable hardware tkip."); |
| 95 |
|
| 96 |
static int modparam_qos = 1; |
| 97 |
module_param_named(qos, modparam_qos, int, 0444); |
| 98 |
MODULE_PARM_DESC(qos, "Enable QOS support (default on)"); |
| 99 |
|
| 100 |
static int modparam_btcoex = 1; |
| 101 |
module_param_named(btcoex, modparam_btcoex, int, 0444); |
| 102 |
MODULE_PARM_DESC(btcoex, "Enable Bluetooth coexistence (default on)"); |
| 103 |
|
| 104 |
int b43_modparam_verbose = B43_VERBOSITY_DEFAULT; |
| 105 |
module_param_named(verbose, b43_modparam_verbose, int, 0644); |
| 106 |
MODULE_PARM_DESC(verbose, "Log message verbosity: 0=error, 1=warn, 2=info(default), 3=debug"); |
| 107 |
|
| 108 |
static int b43_modparam_pio; |
| 109 |
module_param_named(pio, b43_modparam_pio, int, 0644); |
| 110 |
MODULE_PARM_DESC(pio, "Use PIO accesses by default: 0=DMA, 1=PIO"); |
| 111 |
|
| 112 |
static int modparam_allhwsupport = !IS_ENABLED(CONFIG_BRCMSMAC); |
| 113 |
module_param_named(allhwsupport, modparam_allhwsupport, int, 0444); |
| 114 |
MODULE_PARM_DESC(allhwsupport, "Enable support for all hardware (even it if overlaps with the brcmsmac driver)"); |
| 115 |
|
| 116 |
#ifdef CONFIG_B43_BCMA |
| 117 |
static const struct bcma_device_id b43_bcma_tbl[] = { |
| 118 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x11, BCMA_ANY_CLASS), |
| 119 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x15, BCMA_ANY_CLASS), |
| 120 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x17, BCMA_ANY_CLASS), |
| 121 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x18, BCMA_ANY_CLASS), |
| 122 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1C, BCMA_ANY_CLASS), |
| 123 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1D, BCMA_ANY_CLASS), |
| 124 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x1E, BCMA_ANY_CLASS), |
| 125 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x28, BCMA_ANY_CLASS), |
| 126 |
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_80211, 0x2A, BCMA_ANY_CLASS), |
| 127 |
{}, |
| 128 |
}; |
| 129 |
MODULE_DEVICE_TABLE(bcma, b43_bcma_tbl); |
| 130 |
#endif |
| 131 |
|
| 132 |
#ifdef CONFIG_B43_SSB |
| 133 |
static const struct ssb_device_id b43_ssb_tbl[] = { |
| 134 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 5), |
| 135 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 6), |
| 136 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 7), |
| 137 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 9), |
| 138 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 10), |
| 139 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 11), |
| 140 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 12), |
| 141 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 13), |
| 142 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 15), |
| 143 |
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_80211, 16), |
| 144 |
{}, |
| 145 |
}; |
| 146 |
MODULE_DEVICE_TABLE(ssb, b43_ssb_tbl); |
| 147 |
#endif |
| 148 |
|
| 149 |
/* Channel and ratetables are shared for all devices. |
| 150 |
* They can't be const, because ieee80211 puts some precalculated |
| 151 |
* data in there. This data is the same for all devices, so we don't |
| 152 |
* get concurrency issues */ |
| 153 |
#define RATETAB_ENT(_rateid, _flags) \ |
| 154 |
{ \ |
| 155 |
.bitrate = B43_RATE_TO_BASE100KBPS(_rateid), \ |
| 156 |
.hw_value = (_rateid), \ |
| 157 |
.flags = (_flags), \ |
| 158 |
} |
| 159 |
|
| 160 |
/* |
| 161 |
* NOTE: When changing this, sync with xmit.c's |
| 162 |
* b43_plcp_get_bitrate_idx_* functions! |
| 163 |
*/ |
| 164 |
static struct ieee80211_rate __b43_ratetable[] = { |
| 165 |
RATETAB_ENT(B43_CCK_RATE_1MB, 0), |
| 166 |
RATETAB_ENT(B43_CCK_RATE_2MB, IEEE80211_RATE_SHORT_PREAMBLE), |
| 167 |
RATETAB_ENT(B43_CCK_RATE_5MB, IEEE80211_RATE_SHORT_PREAMBLE), |
| 168 |
RATETAB_ENT(B43_CCK_RATE_11MB, IEEE80211_RATE_SHORT_PREAMBLE), |
| 169 |
RATETAB_ENT(B43_OFDM_RATE_6MB, 0), |
| 170 |
RATETAB_ENT(B43_OFDM_RATE_9MB, 0), |
| 171 |
RATETAB_ENT(B43_OFDM_RATE_12MB, 0), |
| 172 |
RATETAB_ENT(B43_OFDM_RATE_18MB, 0), |
| 173 |
RATETAB_ENT(B43_OFDM_RATE_24MB, 0), |
| 174 |
RATETAB_ENT(B43_OFDM_RATE_36MB, 0), |
| 175 |
RATETAB_ENT(B43_OFDM_RATE_48MB, 0), |
| 176 |
RATETAB_ENT(B43_OFDM_RATE_54MB, 0), |
| 177 |
}; |
| 178 |
|
| 179 |
#define b43_a_ratetable (__b43_ratetable + 4) |
| 180 |
#define b43_a_ratetable_size 8 |
| 181 |
#define b43_b_ratetable (__b43_ratetable + 0) |
| 182 |
#define b43_b_ratetable_size 4 |
| 183 |
#define b43_g_ratetable (__b43_ratetable + 0) |
| 184 |
#define b43_g_ratetable_size 12 |
| 185 |
|
| 186 |
#define CHAN2G(_channel, _freq, _flags) { \ |
| 187 |
.band = NL80211_BAND_2GHZ, \ |
| 188 |
.center_freq = (_freq), \ |
| 189 |
.hw_value = (_channel), \ |
| 190 |
.flags = (_flags), \ |
| 191 |
.max_antenna_gain = 0, \ |
| 192 |
.max_power = 30, \ |
| 193 |
} |
| 194 |
static struct ieee80211_channel b43_2ghz_chantable[] = { |
| 195 |
CHAN2G(1, 2412, 0), |
| 196 |
CHAN2G(2, 2417, 0), |
| 197 |
CHAN2G(3, 2422, 0), |
| 198 |
CHAN2G(4, 2427, 0), |
| 199 |
CHAN2G(5, 2432, 0), |
| 200 |
CHAN2G(6, 2437, 0), |
| 201 |
CHAN2G(7, 2442, 0), |
| 202 |
CHAN2G(8, 2447, 0), |
| 203 |
CHAN2G(9, 2452, 0), |
| 204 |
CHAN2G(10, 2457, 0), |
| 205 |
CHAN2G(11, 2462, 0), |
| 206 |
CHAN2G(12, 2467, 0), |
| 207 |
CHAN2G(13, 2472, 0), |
| 208 |
CHAN2G(14, 2484, 0), |
| 209 |
}; |
| 210 |
|
| 211 |
/* No support for the last 3 channels (12, 13, 14) */ |
| 212 |
#define b43_2ghz_chantable_limited_size 11 |
| 213 |
#undef CHAN2G |
| 214 |
|
| 215 |
#define CHAN4G(_channel, _flags) { \ |
| 216 |
.band = NL80211_BAND_5GHZ, \ |
| 217 |
.center_freq = 4000 + (5 * (_channel)), \ |
| 218 |
.hw_value = (_channel), \ |
| 219 |
.flags = (_flags), \ |
| 220 |
.max_antenna_gain = 0, \ |
| 221 |
.max_power = 30, \ |
| 222 |
} |
| 223 |
#define CHAN5G(_channel, _flags) { \ |
| 224 |
.band = NL80211_BAND_5GHZ, \ |
| 225 |
.center_freq = 5000 + (5 * (_channel)), \ |
| 226 |
.hw_value = (_channel), \ |
| 227 |
.flags = (_flags), \ |
| 228 |
.max_antenna_gain = 0, \ |
| 229 |
.max_power = 30, \ |
| 230 |
} |
| 231 |
static struct ieee80211_channel b43_5ghz_nphy_chantable[] = { |
| 232 |
CHAN4G(184, 0), CHAN4G(186, 0), |
| 233 |
CHAN4G(188, 0), CHAN4G(190, 0), |
| 234 |
CHAN4G(192, 0), CHAN4G(194, 0), |
| 235 |
CHAN4G(196, 0), CHAN4G(198, 0), |
| 236 |
CHAN4G(200, 0), CHAN4G(202, 0), |
| 237 |
CHAN4G(204, 0), CHAN4G(206, 0), |
| 238 |
CHAN4G(208, 0), CHAN4G(210, 0), |
| 239 |
CHAN4G(212, 0), CHAN4G(214, 0), |
| 240 |
CHAN4G(216, 0), CHAN4G(218, 0), |
| 241 |
CHAN4G(220, 0), CHAN4G(222, 0), |
| 242 |
CHAN4G(224, 0), CHAN4G(226, 0), |
| 243 |
CHAN4G(228, 0), |
| 244 |
CHAN5G(32, 0), CHAN5G(34, 0), |
| 245 |
CHAN5G(36, 0), CHAN5G(38, 0), |
| 246 |
CHAN5G(40, 0), CHAN5G(42, 0), |
| 247 |
CHAN5G(44, 0), CHAN5G(46, 0), |
| 248 |
CHAN5G(48, 0), CHAN5G(50, 0), |
| 249 |
CHAN5G(52, 0), CHAN5G(54, 0), |
| 250 |
CHAN5G(56, 0), CHAN5G(58, 0), |
| 251 |
CHAN5G(60, 0), CHAN5G(62, 0), |
| 252 |
CHAN5G(64, 0), CHAN5G(66, 0), |
| 253 |
CHAN5G(68, 0), CHAN5G(70, 0), |
| 254 |
CHAN5G(72, 0), CHAN5G(74, 0), |
| 255 |
CHAN5G(76, 0), CHAN5G(78, 0), |
| 256 |
CHAN5G(80, 0), CHAN5G(82, 0), |
| 257 |
CHAN5G(84, 0), CHAN5G(86, 0), |
| 258 |
CHAN5G(88, 0), CHAN5G(90, 0), |
| 259 |
CHAN5G(92, 0), CHAN5G(94, 0), |
| 260 |
CHAN5G(96, 0), CHAN5G(98, 0), |
| 261 |
CHAN5G(100, 0), CHAN5G(102, 0), |
| 262 |
CHAN5G(104, 0), CHAN5G(106, 0), |
| 263 |
CHAN5G(108, 0), CHAN5G(110, 0), |
| 264 |
CHAN5G(112, 0), CHAN5G(114, 0), |
| 265 |
CHAN5G(116, 0), CHAN5G(118, 0), |
| 266 |
CHAN5G(120, 0), CHAN5G(122, 0), |
| 267 |
CHAN5G(124, 0), CHAN5G(126, 0), |
| 268 |
CHAN5G(128, 0), CHAN5G(130, 0), |
| 269 |
CHAN5G(132, 0), CHAN5G(134, 0), |
| 270 |
CHAN5G(136, 0), CHAN5G(138, 0), |
| 271 |
CHAN5G(140, 0), CHAN5G(142, 0), |
| 272 |
CHAN5G(144, 0), CHAN5G(145, 0), |
| 273 |
CHAN5G(146, 0), CHAN5G(147, 0), |
| 274 |
CHAN5G(148, 0), CHAN5G(149, 0), |
| 275 |
CHAN5G(150, 0), CHAN5G(151, 0), |
| 276 |
CHAN5G(152, 0), CHAN5G(153, 0), |
| 277 |
CHAN5G(154, 0), CHAN5G(155, 0), |
| 278 |
CHAN5G(156, 0), CHAN5G(157, 0), |
| 279 |
CHAN5G(158, 0), CHAN5G(159, 0), |
| 280 |
CHAN5G(160, 0), CHAN5G(161, 0), |
| 281 |
CHAN5G(162, 0), CHAN5G(163, 0), |
| 282 |
CHAN5G(164, 0), CHAN5G(165, 0), |
| 283 |
CHAN5G(166, 0), CHAN5G(168, 0), |
| 284 |
CHAN5G(170, 0), CHAN5G(172, 0), |
| 285 |
CHAN5G(174, 0), CHAN5G(176, 0), |
| 286 |
CHAN5G(178, 0), CHAN5G(180, 0), |
| 287 |
CHAN5G(182, 0), |
| 288 |
}; |
| 289 |
|
| 290 |
static struct ieee80211_channel b43_5ghz_nphy_chantable_limited[] = { |
| 291 |
CHAN5G(36, 0), CHAN5G(40, 0), |
| 292 |
CHAN5G(44, 0), CHAN5G(48, 0), |
| 293 |
CHAN5G(149, 0), CHAN5G(153, 0), |
| 294 |
CHAN5G(157, 0), CHAN5G(161, 0), |
| 295 |
CHAN5G(165, 0), |
| 296 |
}; |
| 297 |
|
| 298 |
static struct ieee80211_channel b43_5ghz_aphy_chantable[] = { |
| 299 |
CHAN5G(34, 0), CHAN5G(36, 0), |
| 300 |
CHAN5G(38, 0), CHAN5G(40, 0), |
| 301 |
CHAN5G(42, 0), CHAN5G(44, 0), |
| 302 |
CHAN5G(46, 0), CHAN5G(48, 0), |
| 303 |
CHAN5G(52, 0), CHAN5G(56, 0), |
| 304 |
CHAN5G(60, 0), CHAN5G(64, 0), |
| 305 |
CHAN5G(100, 0), CHAN5G(104, 0), |
| 306 |
CHAN5G(108, 0), CHAN5G(112, 0), |
| 307 |
CHAN5G(116, 0), CHAN5G(120, 0), |
| 308 |
CHAN5G(124, 0), CHAN5G(128, 0), |
| 309 |
CHAN5G(132, 0), CHAN5G(136, 0), |
| 310 |
CHAN5G(140, 0), CHAN5G(149, 0), |
| 311 |
CHAN5G(153, 0), CHAN5G(157, 0), |
| 312 |
CHAN5G(161, 0), CHAN5G(165, 0), |
| 313 |
CHAN5G(184, 0), CHAN5G(188, 0), |
| 314 |
CHAN5G(192, 0), CHAN5G(196, 0), |
| 315 |
CHAN5G(200, 0), CHAN5G(204, 0), |
| 316 |
CHAN5G(208, 0), CHAN5G(212, 0), |
| 317 |
CHAN5G(216, 0), |
| 318 |
}; |
| 319 |
#undef CHAN4G |
| 320 |
#undef CHAN5G |
| 321 |
|
| 322 |
static struct ieee80211_supported_band b43_band_5GHz_nphy = { |
| 323 |
.band = NL80211_BAND_5GHZ, |
| 324 |
.channels = b43_5ghz_nphy_chantable, |
| 325 |
.n_channels = ARRAY_SIZE(b43_5ghz_nphy_chantable), |
| 326 |
.bitrates = b43_a_ratetable, |
| 327 |
.n_bitrates = b43_a_ratetable_size, |
| 328 |
}; |
| 329 |
|
| 330 |
static struct ieee80211_supported_band b43_band_5GHz_nphy_limited = { |
| 331 |
.band = NL80211_BAND_5GHZ, |
| 332 |
.channels = b43_5ghz_nphy_chantable_limited, |
| 333 |
.n_channels = ARRAY_SIZE(b43_5ghz_nphy_chantable_limited), |
| 334 |
.bitrates = b43_a_ratetable, |
| 335 |
.n_bitrates = b43_a_ratetable_size, |
| 336 |
}; |
| 337 |
|
| 338 |
static struct ieee80211_supported_band b43_band_5GHz_aphy = { |
| 339 |
.band = NL80211_BAND_5GHZ, |
| 340 |
.channels = b43_5ghz_aphy_chantable, |
| 341 |
.n_channels = ARRAY_SIZE(b43_5ghz_aphy_chantable), |
| 342 |
.bitrates = b43_a_ratetable, |
| 343 |
.n_bitrates = b43_a_ratetable_size, |
| 344 |
}; |
| 345 |
|
| 346 |
static struct ieee80211_supported_band b43_band_2GHz = { |
| 347 |
.band = NL80211_BAND_2GHZ, |
| 348 |
.channels = b43_2ghz_chantable, |
| 349 |
.n_channels = ARRAY_SIZE(b43_2ghz_chantable), |
| 350 |
.bitrates = b43_g_ratetable, |
| 351 |
.n_bitrates = b43_g_ratetable_size, |
| 352 |
}; |
| 353 |
|
| 354 |
static struct ieee80211_supported_band b43_band_2ghz_limited = { |
| 355 |
.band = NL80211_BAND_2GHZ, |
| 356 |
.channels = b43_2ghz_chantable, |
| 357 |
.n_channels = b43_2ghz_chantable_limited_size, |
| 358 |
.bitrates = b43_g_ratetable, |
| 359 |
.n_bitrates = b43_g_ratetable_size, |
| 360 |
}; |
| 361 |
|
| 362 |
static void b43_wireless_core_exit(struct b43_wldev *dev); |
| 363 |
static int b43_wireless_core_init(struct b43_wldev *dev); |
| 364 |
static struct b43_wldev * b43_wireless_core_stop(struct b43_wldev *dev); |
| 365 |
static int b43_wireless_core_start(struct b43_wldev *dev); |
| 366 |
static void b43_op_bss_info_changed(struct ieee80211_hw *hw, |
| 367 |
struct ieee80211_vif *vif, |
| 368 |
struct ieee80211_bss_conf *conf, |
| 369 |
u64 changed); |
| 370 |
|
| 371 |
static int b43_ratelimit(struct b43_wl *wl) |
| 372 |
{ |
| 373 |
if (!wl || !wl->current_dev) |
| 374 |
return 1; |
| 375 |
if (b43_status(wl->current_dev) < B43_STAT_STARTED) |
| 376 |
return 1; |
| 377 |
/* We are up and running. |
| 378 |
* Ratelimit the messages to avoid DoS over the net. */ |
| 379 |
return net_ratelimit(); |
| 380 |
} |
| 381 |
|
| 382 |
void b43info(struct b43_wl *wl, const char *fmt, ...) |
| 383 |
{ |
| 384 |
struct va_format vaf; |
| 385 |
va_list args; |
| 386 |
|
| 387 |
if (b43_modparam_verbose < B43_VERBOSITY_INFO) |
| 388 |
return; |
| 389 |
if (!b43_ratelimit(wl)) |
| 390 |
return; |
| 391 |
|
| 392 |
va_start(args, fmt); |
| 393 |
|
| 394 |
vaf.fmt = fmt; |
| 395 |
vaf.va = &args; |
| 396 |
|
| 397 |
printk(KERN_INFO "b43-%s: %pV", |
| 398 |
(wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); |
| 399 |
|
| 400 |
va_end(args); |
| 401 |
} |
| 402 |
|
| 403 |
void b43err(struct b43_wl *wl, const char *fmt, ...) |
| 404 |
{ |
| 405 |
struct va_format vaf; |
| 406 |
va_list args; |
| 407 |
|
| 408 |
if (b43_modparam_verbose < B43_VERBOSITY_ERROR) |
| 409 |
return; |
| 410 |
if (!b43_ratelimit(wl)) |
| 411 |
return; |
| 412 |
|
| 413 |
va_start(args, fmt); |
| 414 |
|
| 415 |
vaf.fmt = fmt; |
| 416 |
vaf.va = &args; |
| 417 |
|
| 418 |
printk(KERN_ERR "b43-%s ERROR: %pV", |
| 419 |
(wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); |
| 420 |
|
| 421 |
va_end(args); |
| 422 |
} |
| 423 |
|
| 424 |
void b43warn(struct b43_wl *wl, const char *fmt, ...) |
| 425 |
{ |
| 426 |
struct va_format vaf; |
| 427 |
va_list args; |
| 428 |
|
| 429 |
if (b43_modparam_verbose < B43_VERBOSITY_WARN) |
| 430 |
return; |
| 431 |
if (!b43_ratelimit(wl)) |
| 432 |
return; |
| 433 |
|
| 434 |
va_start(args, fmt); |
| 435 |
|
| 436 |
vaf.fmt = fmt; |
| 437 |
vaf.va = &args; |
| 438 |
|
| 439 |
printk(KERN_WARNING "b43-%s warning: %pV", |
| 440 |
(wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); |
| 441 |
|
| 442 |
va_end(args); |
| 443 |
} |
| 444 |
|
| 445 |
void b43dbg(struct b43_wl *wl, const char *fmt, ...) |
| 446 |
{ |
| 447 |
struct va_format vaf; |
| 448 |
va_list args; |
| 449 |
|
| 450 |
if (b43_modparam_verbose < B43_VERBOSITY_DEBUG) |
| 451 |
return; |
| 452 |
|
| 453 |
va_start(args, fmt); |
| 454 |
|
| 455 |
vaf.fmt = fmt; |
| 456 |
vaf.va = &args; |
| 457 |
|
| 458 |
printk(KERN_DEBUG "b43-%s debug: %pV", |
| 459 |
(wl && wl->hw) ? wiphy_name(wl->hw->wiphy) : "wlan", &vaf); |
| 460 |
|
| 461 |
va_end(args); |
| 462 |
} |
| 463 |
|
| 464 |
static void b43_ram_write(struct b43_wldev *dev, u16 offset, u32 val) |
| 465 |
{ |
| 466 |
u32 macctl; |
| 467 |
|
| 468 |
B43_WARN_ON(offset % 4 != 0); |
| 469 |
|
| 470 |
macctl = b43_read32(dev, B43_MMIO_MACCTL); |
| 471 |
if (macctl & B43_MACCTL_BE) |
| 472 |
val = swab32(val); |
| 473 |
|
| 474 |
b43_write32(dev, B43_MMIO_RAM_CONTROL, offset); |
| 475 |
b43_write32(dev, B43_MMIO_RAM_DATA, val); |
| 476 |
} |
| 477 |
|
| 478 |
static inline void b43_shm_control_word(struct b43_wldev *dev, |
| 479 |
u16 routing, u16 offset) |
| 480 |
{ |
| 481 |
u32 control; |
| 482 |
|
| 483 |
/* "offset" is the WORD offset. */ |
| 484 |
control = routing; |
| 485 |
control <<= 16; |
| 486 |
control |= offset; |
| 487 |
b43_write32(dev, B43_MMIO_SHM_CONTROL, control); |
| 488 |
} |
| 489 |
|
| 490 |
u32 b43_shm_read32(struct b43_wldev *dev, u16 routing, u16 offset) |
| 491 |
{ |
| 492 |
u32 ret; |
| 493 |
|
| 494 |
if (routing == B43_SHM_SHARED) { |
| 495 |
B43_WARN_ON(offset & 0x0001); |
| 496 |
if (offset & 0x0003) { |
| 497 |
/* Unaligned access */ |
| 498 |
b43_shm_control_word(dev, routing, offset >> 2); |
| 499 |
ret = b43_read16(dev, B43_MMIO_SHM_DATA_UNALIGNED); |
| 500 |
b43_shm_control_word(dev, routing, (offset >> 2) + 1); |
| 501 |
ret |= ((u32)b43_read16(dev, B43_MMIO_SHM_DATA)) << 16; |
| 502 |
|
| 503 |
goto out; |
| 504 |
} |
| 505 |
offset >>= 2; |
| 506 |
} |
| 507 |
b43_shm_control_word(dev, routing, offset); |
| 508 |
ret = b43_read32(dev, B43_MMIO_SHM_DATA); |
| 509 |
out: |
| 510 |
return ret; |
| 511 |
} |
| 512 |
|
| 513 |
u16 b43_shm_read16(struct b43_wldev *dev, u16 routing, u16 offset) |
| 514 |
{ |
| 515 |
u16 ret; |
| 516 |
|
| 517 |
if (routing == B43_SHM_SHARED) { |
| 518 |
B43_WARN_ON(offset & 0x0001); |
| 519 |
if (offset & 0x0003) { |
| 520 |
/* Unaligned access */ |
| 521 |
b43_shm_control_word(dev, routing, offset >> 2); |
| 522 |
ret = b43_read16(dev, B43_MMIO_SHM_DATA_UNALIGNED); |
| 523 |
|
| 524 |
goto out; |
| 525 |
} |
| 526 |
offset >>= 2; |
| 527 |
} |
| 528 |
b43_shm_control_word(dev, routing, offset); |
| 529 |
ret = b43_read16(dev, B43_MMIO_SHM_DATA); |
| 530 |
out: |
| 531 |
return ret; |
| 532 |
} |
| 533 |
|
| 534 |
void b43_shm_write32(struct b43_wldev *dev, u16 routing, u16 offset, u32 value) |
| 535 |
{ |
| 536 |
if (routing == B43_SHM_SHARED) { |
| 537 |
B43_WARN_ON(offset & 0x0001); |
| 538 |
if (offset & 0x0003) { |
| 539 |
/* Unaligned access */ |
| 540 |
b43_shm_control_word(dev, routing, offset >> 2); |
| 541 |
b43_write16(dev, B43_MMIO_SHM_DATA_UNALIGNED, |
| 542 |
value & 0xFFFF); |
| 543 |
b43_shm_control_word(dev, routing, (offset >> 2) + 1); |
| 544 |
b43_write16(dev, B43_MMIO_SHM_DATA, |
| 545 |
(value >> 16) & 0xFFFF); |
| 546 |
return; |
| 547 |
} |
| 548 |
offset >>= 2; |
| 549 |
} |
| 550 |
b43_shm_control_word(dev, routing, offset); |
| 551 |
b43_write32(dev, B43_MMIO_SHM_DATA, value); |
| 552 |
} |
| 553 |
|
| 554 |
void b43_shm_write16(struct b43_wldev *dev, u16 routing, u16 offset, u16 value) |
| 555 |
{ |
| 556 |
if (routing == B43_SHM_SHARED) { |
| 557 |
B43_WARN_ON(offset & 0x0001); |
| 558 |
if (offset & 0x0003) { |
| 559 |
/* Unaligned access */ |
| 560 |
b43_shm_control_word(dev, routing, offset >> 2); |
| 561 |
b43_write16(dev, B43_MMIO_SHM_DATA_UNALIGNED, value); |
| 562 |
return; |
| 563 |
} |
| 564 |
offset >>= 2; |
| 565 |
} |
| 566 |
b43_shm_control_word(dev, routing, offset); |
| 567 |
b43_write16(dev, B43_MMIO_SHM_DATA, value); |
| 568 |
} |
| 569 |
|
| 570 |
/* Read HostFlags */ |
| 571 |
u64 b43_hf_read(struct b43_wldev *dev) |
| 572 |
{ |
| 573 |
u64 ret; |
| 574 |
|
| 575 |
ret = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF3); |
| 576 |
ret <<= 16; |
| 577 |
ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF2); |
| 578 |
ret <<= 16; |
| 579 |
ret |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF1); |
| 580 |
|
| 581 |
return ret; |
| 582 |
} |
| 583 |
|
| 584 |
/* Write HostFlags */ |
| 585 |
void b43_hf_write(struct b43_wldev *dev, u64 value) |
| 586 |
{ |
| 587 |
u16 lo, mi, hi; |
| 588 |
|
| 589 |
lo = (value & 0x00000000FFFFULL); |
| 590 |
mi = (value & 0x0000FFFF0000ULL) >> 16; |
| 591 |
hi = (value & 0xFFFF00000000ULL) >> 32; |
| 592 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF1, lo); |
| 593 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF2, mi); |
| 594 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTF3, hi); |
| 595 |
} |
| 596 |
|
| 597 |
/* Read the firmware capabilities bitmask (Opensource firmware only) */ |
| 598 |
static u16 b43_fwcapa_read(struct b43_wldev *dev) |
| 599 |
{ |
| 600 |
B43_WARN_ON(!dev->fw.opensource); |
| 601 |
return b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_FWCAPA); |
| 602 |
} |
| 603 |
|
| 604 |
void b43_tsf_read(struct b43_wldev *dev, u64 *tsf) |
| 605 |
{ |
| 606 |
u32 low, high; |
| 607 |
|
| 608 |
B43_WARN_ON(dev->dev->core_rev < 3); |
| 609 |
|
| 610 |
/* The hardware guarantees us an atomic read, if we |
| 611 |
* read the low register first. */ |
| 612 |
low = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_LOW); |
| 613 |
high = b43_read32(dev, B43_MMIO_REV3PLUS_TSF_HIGH); |
| 614 |
|
| 615 |
*tsf = high; |
| 616 |
*tsf <<= 32; |
| 617 |
*tsf |= low; |
| 618 |
} |
| 619 |
|
| 620 |
static void b43_time_lock(struct b43_wldev *dev) |
| 621 |
{ |
| 622 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_TBTTHOLD); |
| 623 |
/* Commit the write */ |
| 624 |
b43_read32(dev, B43_MMIO_MACCTL); |
| 625 |
} |
| 626 |
|
| 627 |
static void b43_time_unlock(struct b43_wldev *dev) |
| 628 |
{ |
| 629 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_TBTTHOLD, 0); |
| 630 |
/* Commit the write */ |
| 631 |
b43_read32(dev, B43_MMIO_MACCTL); |
| 632 |
} |
| 633 |
|
| 634 |
static void b43_tsf_write_locked(struct b43_wldev *dev, u64 tsf) |
| 635 |
{ |
| 636 |
u32 low, high; |
| 637 |
|
| 638 |
B43_WARN_ON(dev->dev->core_rev < 3); |
| 639 |
|
| 640 |
low = tsf; |
| 641 |
high = (tsf >> 32); |
| 642 |
/* The hardware guarantees us an atomic write, if we |
| 643 |
* write the low register first. */ |
| 644 |
b43_write32(dev, B43_MMIO_REV3PLUS_TSF_LOW, low); |
| 645 |
b43_write32(dev, B43_MMIO_REV3PLUS_TSF_HIGH, high); |
| 646 |
} |
| 647 |
|
| 648 |
void b43_tsf_write(struct b43_wldev *dev, u64 tsf) |
| 649 |
{ |
| 650 |
b43_time_lock(dev); |
| 651 |
b43_tsf_write_locked(dev, tsf); |
| 652 |
b43_time_unlock(dev); |
| 653 |
} |
| 654 |
|
| 655 |
static |
| 656 |
void b43_macfilter_set(struct b43_wldev *dev, u16 offset, const u8 *mac) |
| 657 |
{ |
| 658 |
static const u8 zero_addr[ETH_ALEN] = { 0 }; |
| 659 |
u16 data; |
| 660 |
|
| 661 |
if (!mac) |
| 662 |
mac = zero_addr; |
| 663 |
|
| 664 |
offset |= 0x0020; |
| 665 |
b43_write16(dev, B43_MMIO_MACFILTER_CONTROL, offset); |
| 666 |
|
| 667 |
data = mac[0]; |
| 668 |
data |= mac[1] << 8; |
| 669 |
b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); |
| 670 |
data = mac[2]; |
| 671 |
data |= mac[3] << 8; |
| 672 |
b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); |
| 673 |
data = mac[4]; |
| 674 |
data |= mac[5] << 8; |
| 675 |
b43_write16(dev, B43_MMIO_MACFILTER_DATA, data); |
| 676 |
} |
| 677 |
|
| 678 |
static void b43_write_mac_bssid_templates(struct b43_wldev *dev) |
| 679 |
{ |
| 680 |
const u8 *mac; |
| 681 |
const u8 *bssid; |
| 682 |
u8 mac_bssid[ETH_ALEN * 2]; |
| 683 |
int i; |
| 684 |
u32 tmp; |
| 685 |
|
| 686 |
bssid = dev->wl->bssid; |
| 687 |
mac = dev->wl->mac_addr; |
| 688 |
|
| 689 |
b43_macfilter_set(dev, B43_MACFILTER_BSSID, bssid); |
| 690 |
|
| 691 |
memcpy(mac_bssid, mac, ETH_ALEN); |
| 692 |
memcpy(mac_bssid + ETH_ALEN, bssid, ETH_ALEN); |
| 693 |
|
| 694 |
/* Write our MAC address and BSSID to template ram */ |
| 695 |
for (i = 0; i < ARRAY_SIZE(mac_bssid); i += sizeof(u32)) { |
| 696 |
tmp = (u32) (mac_bssid[i + 0]); |
| 697 |
tmp |= (u32) (mac_bssid[i + 1]) << 8; |
| 698 |
tmp |= (u32) (mac_bssid[i + 2]) << 16; |
| 699 |
tmp |= (u32) (mac_bssid[i + 3]) << 24; |
| 700 |
b43_ram_write(dev, 0x20 + i, tmp); |
| 701 |
} |
| 702 |
} |
| 703 |
|
| 704 |
static void b43_upload_card_macaddress(struct b43_wldev *dev) |
| 705 |
{ |
| 706 |
b43_write_mac_bssid_templates(dev); |
| 707 |
b43_macfilter_set(dev, B43_MACFILTER_SELF, dev->wl->mac_addr); |
| 708 |
} |
| 709 |
|
| 710 |
static void b43_set_slot_time(struct b43_wldev *dev, u16 slot_time) |
| 711 |
{ |
| 712 |
/* slot_time is in usec. */ |
| 713 |
/* This test used to exit for all but a G PHY. */ |
| 714 |
if (b43_current_band(dev->wl) == NL80211_BAND_5GHZ) |
| 715 |
return; |
| 716 |
b43_write16(dev, B43_MMIO_IFSSLOT, 510 + slot_time); |
| 717 |
/* Shared memory location 0x0010 is the slot time and should be |
| 718 |
* set to slot_time; however, this register is initially 0 and changing |
| 719 |
* the value adversely affects the transmit rate for BCM4311 |
| 720 |
* devices. Until this behavior is unterstood, delete this step |
| 721 |
* |
| 722 |
* b43_shm_write16(dev, B43_SHM_SHARED, 0x0010, slot_time); |
| 723 |
*/ |
| 724 |
} |
| 725 |
|
| 726 |
static void b43_short_slot_timing_enable(struct b43_wldev *dev) |
| 727 |
{ |
| 728 |
b43_set_slot_time(dev, 9); |
| 729 |
} |
| 730 |
|
| 731 |
static void b43_short_slot_timing_disable(struct b43_wldev *dev) |
| 732 |
{ |
| 733 |
b43_set_slot_time(dev, 20); |
| 734 |
} |
| 735 |
|
| 736 |
/* DummyTransmission function, as documented on |
| 737 |
* https://bcm-v4.sipsolutions.net/802.11/DummyTransmission |
| 738 |
*/ |
| 739 |
void b43_dummy_transmission(struct b43_wldev *dev, bool ofdm, bool pa_on) |
| 740 |
{ |
| 741 |
struct b43_phy *phy = &dev->phy; |
| 742 |
unsigned int i, max_loop; |
| 743 |
u16 value; |
| 744 |
u32 buffer[5] = { |
| 745 |
0x00000000, |
| 746 |
0x00D40000, |
| 747 |
0x00000000, |
| 748 |
0x01000000, |
| 749 |
0x00000000, |
| 750 |
}; |
| 751 |
|
| 752 |
if (ofdm) { |
| 753 |
max_loop = 0x1E; |
| 754 |
buffer[0] = 0x000201CC; |
| 755 |
} else { |
| 756 |
max_loop = 0xFA; |
| 757 |
buffer[0] = 0x000B846E; |
| 758 |
} |
| 759 |
|
| 760 |
for (i = 0; i < 5; i++) |
| 761 |
b43_ram_write(dev, i * 4, buffer[i]); |
| 762 |
|
| 763 |
b43_write16(dev, B43_MMIO_XMTSEL, 0x0000); |
| 764 |
|
| 765 |
if (dev->dev->core_rev < 11) |
| 766 |
b43_write16(dev, B43_MMIO_WEPCTL, 0x0000); |
| 767 |
else |
| 768 |
b43_write16(dev, B43_MMIO_WEPCTL, 0x0100); |
| 769 |
|
| 770 |
value = (ofdm ? 0x41 : 0x40); |
| 771 |
b43_write16(dev, B43_MMIO_TXE0_PHYCTL, value); |
| 772 |
if (phy->type == B43_PHYTYPE_N || phy->type == B43_PHYTYPE_LP || |
| 773 |
phy->type == B43_PHYTYPE_LCN) |
| 774 |
b43_write16(dev, B43_MMIO_TXE0_PHYCTL1, 0x1A02); |
| 775 |
|
| 776 |
b43_write16(dev, B43_MMIO_TXE0_WM_0, 0x0000); |
| 777 |
b43_write16(dev, B43_MMIO_TXE0_WM_1, 0x0000); |
| 778 |
|
| 779 |
b43_write16(dev, B43_MMIO_XMTTPLATETXPTR, 0x0000); |
| 780 |
b43_write16(dev, B43_MMIO_XMTTXCNT, 0x0014); |
| 781 |
b43_write16(dev, B43_MMIO_XMTSEL, 0x0826); |
| 782 |
b43_write16(dev, B43_MMIO_TXE0_CTL, 0x0000); |
| 783 |
|
| 784 |
if (!pa_on && phy->type == B43_PHYTYPE_N) { |
| 785 |
; /*b43_nphy_pa_override(dev, false) */ |
| 786 |
} |
| 787 |
|
| 788 |
switch (phy->type) { |
| 789 |
case B43_PHYTYPE_N: |
| 790 |
case B43_PHYTYPE_LCN: |
| 791 |
b43_write16(dev, B43_MMIO_TXE0_AUX, 0x00D0); |
| 792 |
break; |
| 793 |
case B43_PHYTYPE_LP: |
| 794 |
b43_write16(dev, B43_MMIO_TXE0_AUX, 0x0050); |
| 795 |
break; |
| 796 |
default: |
| 797 |
b43_write16(dev, B43_MMIO_TXE0_AUX, 0x0030); |
| 798 |
} |
| 799 |
b43_read16(dev, B43_MMIO_TXE0_AUX); |
| 800 |
|
| 801 |
if (phy->radio_ver == 0x2050 && phy->radio_rev <= 0x5) |
| 802 |
b43_radio_write16(dev, 0x0051, 0x0017); |
| 803 |
for (i = 0x00; i < max_loop; i++) { |
| 804 |
value = b43_read16(dev, B43_MMIO_TXE0_STATUS); |
| 805 |
if (value & 0x0080) |
| 806 |
break; |
| 807 |
udelay(10); |
| 808 |
} |
| 809 |
for (i = 0x00; i < 0x0A; i++) { |
| 810 |
value = b43_read16(dev, B43_MMIO_TXE0_STATUS); |
| 811 |
if (value & 0x0400) |
| 812 |
break; |
| 813 |
udelay(10); |
| 814 |
} |
| 815 |
for (i = 0x00; i < 0x19; i++) { |
| 816 |
value = b43_read16(dev, B43_MMIO_IFSSTAT); |
| 817 |
if (!(value & 0x0100)) |
| 818 |
break; |
| 819 |
udelay(10); |
| 820 |
} |
| 821 |
if (phy->radio_ver == 0x2050 && phy->radio_rev <= 0x5) |
| 822 |
b43_radio_write16(dev, 0x0051, 0x0037); |
| 823 |
} |
| 824 |
|
| 825 |
static void key_write(struct b43_wldev *dev, |
| 826 |
u8 index, u8 algorithm, const u8 *key) |
| 827 |
{ |
| 828 |
unsigned int i; |
| 829 |
u32 offset; |
| 830 |
u16 value; |
| 831 |
u16 kidx; |
| 832 |
|
| 833 |
/* Key index/algo block */ |
| 834 |
kidx = b43_kidx_to_fw(dev, index); |
| 835 |
value = ((kidx << 4) | algorithm); |
| 836 |
b43_shm_write16(dev, B43_SHM_SHARED, |
| 837 |
B43_SHM_SH_KEYIDXBLOCK + (kidx * 2), value); |
| 838 |
|
| 839 |
/* Write the key to the Key Table Pointer offset */ |
| 840 |
offset = dev->ktp + (index * B43_SEC_KEYSIZE); |
| 841 |
for (i = 0; i < B43_SEC_KEYSIZE; i += 2) { |
| 842 |
value = key[i]; |
| 843 |
value |= (u16) (key[i + 1]) << 8; |
| 844 |
b43_shm_write16(dev, B43_SHM_SHARED, offset + i, value); |
| 845 |
} |
| 846 |
} |
| 847 |
|
| 848 |
static void keymac_write(struct b43_wldev *dev, u8 index, const u8 *addr) |
| 849 |
{ |
| 850 |
u32 addrtmp[2] = { 0, 0, }; |
| 851 |
u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; |
| 852 |
|
| 853 |
if (b43_new_kidx_api(dev)) |
| 854 |
pairwise_keys_start = B43_NR_GROUP_KEYS; |
| 855 |
|
| 856 |
B43_WARN_ON(index < pairwise_keys_start); |
| 857 |
/* We have four default TX keys and possibly four default RX keys. |
| 858 |
* Physical mac 0 is mapped to physical key 4 or 8, depending |
| 859 |
* on the firmware version. |
| 860 |
* So we must adjust the index here. |
| 861 |
*/ |
| 862 |
index -= pairwise_keys_start; |
| 863 |
B43_WARN_ON(index >= B43_NR_PAIRWISE_KEYS); |
| 864 |
|
| 865 |
if (addr) { |
| 866 |
addrtmp[0] = addr[0]; |
| 867 |
addrtmp[0] |= ((u32) (addr[1]) << 8); |
| 868 |
addrtmp[0] |= ((u32) (addr[2]) << 16); |
| 869 |
addrtmp[0] |= ((u32) (addr[3]) << 24); |
| 870 |
addrtmp[1] = addr[4]; |
| 871 |
addrtmp[1] |= ((u32) (addr[5]) << 8); |
| 872 |
} |
| 873 |
|
| 874 |
/* Receive match transmitter address (RCMTA) mechanism */ |
| 875 |
b43_shm_write32(dev, B43_SHM_RCMTA, |
| 876 |
(index * 2) + 0, addrtmp[0]); |
| 877 |
b43_shm_write16(dev, B43_SHM_RCMTA, |
| 878 |
(index * 2) + 1, addrtmp[1]); |
| 879 |
} |
| 880 |
|
| 881 |
/* The ucode will use phase1 key with TEK key to decrypt rx packets. |
| 882 |
* When a packet is received, the iv32 is checked. |
| 883 |
* - if it doesn't the packet is returned without modification (and software |
| 884 |
* decryption can be done). That's what happen when iv16 wrap. |
| 885 |
* - if it does, the rc4 key is computed, and decryption is tried. |
| 886 |
* Either it will success and B43_RX_MAC_DEC is returned, |
| 887 |
* either it fails and B43_RX_MAC_DEC|B43_RX_MAC_DECERR is returned |
| 888 |
* and the packet is not usable (it got modified by the ucode). |
| 889 |
* So in order to never have B43_RX_MAC_DECERR, we should provide |
| 890 |
* a iv32 and phase1key that match. Because we drop packets in case of |
| 891 |
* B43_RX_MAC_DECERR, if we have a correct iv32 but a wrong phase1key, all |
| 892 |
* packets will be lost without higher layer knowing (ie no resync possible |
| 893 |
* until next wrap). |
| 894 |
* |
| 895 |
* NOTE : this should support 50 key like RCMTA because |
| 896 |
* (B43_SHM_SH_KEYIDXBLOCK - B43_SHM_SH_TKIPTSCTTAK)/14 = 50 |
| 897 |
*/ |
| 898 |
static void rx_tkip_phase1_write(struct b43_wldev *dev, u8 index, u32 iv32, |
| 899 |
u16 *phase1key) |
| 900 |
{ |
| 901 |
unsigned int i; |
| 902 |
u32 offset; |
| 903 |
u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; |
| 904 |
|
| 905 |
if (!modparam_hwtkip) |
| 906 |
return; |
| 907 |
|
| 908 |
if (b43_new_kidx_api(dev)) |
| 909 |
pairwise_keys_start = B43_NR_GROUP_KEYS; |
| 910 |
|
| 911 |
B43_WARN_ON(index < pairwise_keys_start); |
| 912 |
/* We have four default TX keys and possibly four default RX keys. |
| 913 |
* Physical mac 0 is mapped to physical key 4 or 8, depending |
| 914 |
* on the firmware version. |
| 915 |
* So we must adjust the index here. |
| 916 |
*/ |
| 917 |
index -= pairwise_keys_start; |
| 918 |
B43_WARN_ON(index >= B43_NR_PAIRWISE_KEYS); |
| 919 |
|
| 920 |
if (b43_debug(dev, B43_DBG_KEYS)) { |
| 921 |
b43dbg(dev->wl, "rx_tkip_phase1_write : idx 0x%x, iv32 0x%x\n", |
| 922 |
index, iv32); |
| 923 |
} |
| 924 |
/* Write the key to the RX tkip shared mem */ |
| 925 |
offset = B43_SHM_SH_TKIPTSCTTAK + index * (10 + 4); |
| 926 |
for (i = 0; i < 10; i += 2) { |
| 927 |
b43_shm_write16(dev, B43_SHM_SHARED, offset + i, |
| 928 |
phase1key ? phase1key[i / 2] : 0); |
| 929 |
} |
| 930 |
b43_shm_write16(dev, B43_SHM_SHARED, offset + i, iv32); |
| 931 |
b43_shm_write16(dev, B43_SHM_SHARED, offset + i + 2, iv32 >> 16); |
| 932 |
} |
| 933 |
|
| 934 |
static void b43_op_update_tkip_key(struct ieee80211_hw *hw, |
| 935 |
struct ieee80211_vif *vif, |
| 936 |
struct ieee80211_key_conf *keyconf, |
| 937 |
struct ieee80211_sta *sta, |
| 938 |
u32 iv32, u16 *phase1key) |
| 939 |
{ |
| 940 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 941 |
struct b43_wldev *dev; |
| 942 |
int index = keyconf->hw_key_idx; |
| 943 |
|
| 944 |
if (B43_WARN_ON(!modparam_hwtkip)) |
| 945 |
return; |
| 946 |
|
| 947 |
/* This is only called from the RX path through mac80211, where |
| 948 |
* our mutex is already locked. */ |
| 949 |
B43_WARN_ON(!mutex_is_locked(&wl->mutex)); |
| 950 |
dev = wl->current_dev; |
| 951 |
B43_WARN_ON(!dev || b43_status(dev) < B43_STAT_INITIALIZED); |
| 952 |
|
| 953 |
keymac_write(dev, index, NULL); /* First zero out mac to avoid race */ |
| 954 |
|
| 955 |
rx_tkip_phase1_write(dev, index, iv32, phase1key); |
| 956 |
/* only pairwise TKIP keys are supported right now */ |
| 957 |
if (WARN_ON(!sta)) |
| 958 |
return; |
| 959 |
keymac_write(dev, index, sta->addr); |
| 960 |
} |
| 961 |
|
| 962 |
static void do_key_write(struct b43_wldev *dev, |
| 963 |
u8 index, u8 algorithm, |
| 964 |
const u8 *key, size_t key_len, const u8 *mac_addr) |
| 965 |
{ |
| 966 |
u8 buf[B43_SEC_KEYSIZE] = { 0, }; |
| 967 |
u8 pairwise_keys_start = B43_NR_GROUP_KEYS * 2; |
| 968 |
|
| 969 |
if (b43_new_kidx_api(dev)) |
| 970 |
pairwise_keys_start = B43_NR_GROUP_KEYS; |
| 971 |
|
| 972 |
B43_WARN_ON(index >= ARRAY_SIZE(dev->key)); |
| 973 |
B43_WARN_ON(key_len > B43_SEC_KEYSIZE); |
| 974 |
|
| 975 |
if (index >= pairwise_keys_start) |
| 976 |
keymac_write(dev, index, NULL); /* First zero out mac. */ |
| 977 |
if (algorithm == B43_SEC_ALGO_TKIP) { |
| 978 |
/* |
| 979 |
* We should provide an initial iv32, phase1key pair. |
| 980 |
* We could start with iv32=0 and compute the corresponding |
| 981 |
* phase1key, but this means calling ieee80211_get_tkip_key |
| 982 |
* with a fake skb (or export other tkip function). |
| 983 |
* Because we are lazy we hope iv32 won't start with |
| 984 |
* 0xffffffff and let's b43_op_update_tkip_key provide a |
| 985 |
* correct pair. |
| 986 |
*/ |
| 987 |
rx_tkip_phase1_write(dev, index, 0xffffffff, (u16*)buf); |
| 988 |
} else if (index >= pairwise_keys_start) /* clear it */ |
| 989 |
rx_tkip_phase1_write(dev, index, 0, NULL); |
| 990 |
if (key) |
| 991 |
memcpy(buf, key, key_len); |
| 992 |
key_write(dev, index, algorithm, buf); |
| 993 |
if (index >= pairwise_keys_start) |
| 994 |
keymac_write(dev, index, mac_addr); |
| 995 |
|
| 996 |
dev->key[index].algorithm = algorithm; |
| 997 |
} |
| 998 |
|
| 999 |
static int b43_key_write(struct b43_wldev *dev, |
| 1000 |
int index, u8 algorithm, |
| 1001 |
const u8 *key, size_t key_len, |
| 1002 |
const u8 *mac_addr, |
| 1003 |
struct ieee80211_key_conf *keyconf) |
| 1004 |
{ |
| 1005 |
int i; |
| 1006 |
int pairwise_keys_start; |
| 1007 |
|
| 1008 |
/* For ALG_TKIP the key is encoded as a 256-bit (32 byte) data block: |
| 1009 |
* - Temporal Encryption Key (128 bits) |
| 1010 |
* - Temporal Authenticator Tx MIC Key (64 bits) |
| 1011 |
* - Temporal Authenticator Rx MIC Key (64 bits) |
| 1012 |
* |
| 1013 |
* Hardware only store TEK |
| 1014 |
*/ |
| 1015 |
if (algorithm == B43_SEC_ALGO_TKIP && key_len == 32) |
| 1016 |
key_len = 16; |
| 1017 |
if (key_len > B43_SEC_KEYSIZE) |
| 1018 |
return -EINVAL; |
| 1019 |
for (i = 0; i < ARRAY_SIZE(dev->key); i++) { |
| 1020 |
/* Check that we don't already have this key. */ |
| 1021 |
B43_WARN_ON(dev->key[i].keyconf == keyconf); |
| 1022 |
} |
| 1023 |
if (index < 0) { |
| 1024 |
/* Pairwise key. Get an empty slot for the key. */ |
| 1025 |
if (b43_new_kidx_api(dev)) |
| 1026 |
pairwise_keys_start = B43_NR_GROUP_KEYS; |
| 1027 |
else |
| 1028 |
pairwise_keys_start = B43_NR_GROUP_KEYS * 2; |
| 1029 |
for (i = pairwise_keys_start; |
| 1030 |
i < pairwise_keys_start + B43_NR_PAIRWISE_KEYS; |
| 1031 |
i++) { |
| 1032 |
B43_WARN_ON(i >= ARRAY_SIZE(dev->key)); |
| 1033 |
if (!dev->key[i].keyconf) { |
| 1034 |
/* found empty */ |
| 1035 |
index = i; |
| 1036 |
break; |
| 1037 |
} |
| 1038 |
} |
| 1039 |
if (index < 0) { |
| 1040 |
b43warn(dev->wl, "Out of hardware key memory\n"); |
| 1041 |
return -ENOSPC; |
| 1042 |
} |
| 1043 |
} else |
| 1044 |
B43_WARN_ON(index > 3); |
| 1045 |
|
| 1046 |
do_key_write(dev, index, algorithm, key, key_len, mac_addr); |
| 1047 |
if ((index <= 3) && !b43_new_kidx_api(dev)) { |
| 1048 |
/* Default RX key */ |
| 1049 |
B43_WARN_ON(mac_addr); |
| 1050 |
do_key_write(dev, index + 4, algorithm, key, key_len, NULL); |
| 1051 |
} |
| 1052 |
keyconf->hw_key_idx = index; |
| 1053 |
dev->key[index].keyconf = keyconf; |
| 1054 |
|
| 1055 |
return 0; |
| 1056 |
} |
| 1057 |
|
| 1058 |
static int b43_key_clear(struct b43_wldev *dev, int index) |
| 1059 |
{ |
| 1060 |
if (B43_WARN_ON((index < 0) || (index >= ARRAY_SIZE(dev->key)))) |
| 1061 |
return -EINVAL; |
| 1062 |
do_key_write(dev, index, B43_SEC_ALGO_NONE, |
| 1063 |
NULL, B43_SEC_KEYSIZE, NULL); |
| 1064 |
if ((index <= 3) && !b43_new_kidx_api(dev)) { |
| 1065 |
do_key_write(dev, index + 4, B43_SEC_ALGO_NONE, |
| 1066 |
NULL, B43_SEC_KEYSIZE, NULL); |
| 1067 |
} |
| 1068 |
dev->key[index].keyconf = NULL; |
| 1069 |
|
| 1070 |
return 0; |
| 1071 |
} |
| 1072 |
|
| 1073 |
static void b43_clear_keys(struct b43_wldev *dev) |
| 1074 |
{ |
| 1075 |
int i, count; |
| 1076 |
|
| 1077 |
if (b43_new_kidx_api(dev)) |
| 1078 |
count = B43_NR_GROUP_KEYS + B43_NR_PAIRWISE_KEYS; |
| 1079 |
else |
| 1080 |
count = B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS; |
| 1081 |
for (i = 0; i < count; i++) |
| 1082 |
b43_key_clear(dev, i); |
| 1083 |
} |
| 1084 |
|
| 1085 |
static void b43_dump_keymemory(struct b43_wldev *dev) |
| 1086 |
{ |
| 1087 |
unsigned int i, index, count, offset, pairwise_keys_start; |
| 1088 |
u8 mac[ETH_ALEN]; |
| 1089 |
u16 algo; |
| 1090 |
u32 rcmta0; |
| 1091 |
u16 rcmta1; |
| 1092 |
u64 hf; |
| 1093 |
struct b43_key *key; |
| 1094 |
|
| 1095 |
if (!b43_debug(dev, B43_DBG_KEYS)) |
| 1096 |
return; |
| 1097 |
|
| 1098 |
hf = b43_hf_read(dev); |
| 1099 |
b43dbg(dev->wl, "Hardware key memory dump: USEDEFKEYS=%u\n", |
| 1100 |
!!(hf & B43_HF_USEDEFKEYS)); |
| 1101 |
if (b43_new_kidx_api(dev)) { |
| 1102 |
pairwise_keys_start = B43_NR_GROUP_KEYS; |
| 1103 |
count = B43_NR_GROUP_KEYS + B43_NR_PAIRWISE_KEYS; |
| 1104 |
} else { |
| 1105 |
pairwise_keys_start = B43_NR_GROUP_KEYS * 2; |
| 1106 |
count = B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS; |
| 1107 |
} |
| 1108 |
for (index = 0; index < count; index++) { |
| 1109 |
key = &(dev->key[index]); |
| 1110 |
printk(KERN_DEBUG "Key slot %02u: %s", |
| 1111 |
index, (key->keyconf == NULL) ? " " : "*"); |
| 1112 |
offset = dev->ktp + (index * B43_SEC_KEYSIZE); |
| 1113 |
for (i = 0; i < B43_SEC_KEYSIZE; i += 2) { |
| 1114 |
u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, offset + i); |
| 1115 |
printk("%02X%02X", (tmp & 0xFF), ((tmp >> 8) & 0xFF)); |
| 1116 |
} |
| 1117 |
|
| 1118 |
algo = b43_shm_read16(dev, B43_SHM_SHARED, |
| 1119 |
B43_SHM_SH_KEYIDXBLOCK + (index * 2)); |
| 1120 |
printk(" Algo: %04X/%02X", algo, key->algorithm); |
| 1121 |
|
| 1122 |
if (index >= pairwise_keys_start) { |
| 1123 |
if (key->algorithm == B43_SEC_ALGO_TKIP) { |
| 1124 |
printk(" TKIP: "); |
| 1125 |
offset = B43_SHM_SH_TKIPTSCTTAK + (index - 4) * (10 + 4); |
| 1126 |
for (i = 0; i < 14; i += 2) { |
| 1127 |
u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, offset + i); |
| 1128 |
printk("%02X%02X", (tmp & 0xFF), ((tmp >> 8) & 0xFF)); |
| 1129 |
} |
| 1130 |
} |
| 1131 |
rcmta0 = b43_shm_read32(dev, B43_SHM_RCMTA, |
| 1132 |
((index - pairwise_keys_start) * 2) + 0); |
| 1133 |
rcmta1 = b43_shm_read16(dev, B43_SHM_RCMTA, |
| 1134 |
((index - pairwise_keys_start) * 2) + 1); |
| 1135 |
*((__le32 *)(&mac[0])) = cpu_to_le32(rcmta0); |
| 1136 |
*((__le16 *)(&mac[4])) = cpu_to_le16(rcmta1); |
| 1137 |
printk(" MAC: %pM", mac); |
| 1138 |
} else |
| 1139 |
printk(" DEFAULT KEY"); |
| 1140 |
printk("\n"); |
| 1141 |
} |
| 1142 |
} |
| 1143 |
|
| 1144 |
void b43_power_saving_ctl_bits(struct b43_wldev *dev, unsigned int ps_flags) |
| 1145 |
{ |
| 1146 |
u32 macctl; |
| 1147 |
u16 ucstat; |
| 1148 |
bool hwps; |
| 1149 |
bool awake; |
| 1150 |
int i; |
| 1151 |
|
| 1152 |
B43_WARN_ON((ps_flags & B43_PS_ENABLED) && |
| 1153 |
(ps_flags & B43_PS_DISABLED)); |
| 1154 |
B43_WARN_ON((ps_flags & B43_PS_AWAKE) && (ps_flags & B43_PS_ASLEEP)); |
| 1155 |
|
| 1156 |
if (ps_flags & B43_PS_ENABLED) { |
| 1157 |
hwps = true; |
| 1158 |
} else if (ps_flags & B43_PS_DISABLED) { |
| 1159 |
hwps = false; |
| 1160 |
} else { |
| 1161 |
//TODO: If powersave is not off and FIXME is not set and we are not in adhoc |
| 1162 |
// and thus is not an AP and we are associated, set bit 25 |
| 1163 |
} |
| 1164 |
if (ps_flags & B43_PS_AWAKE) { |
| 1165 |
awake = true; |
| 1166 |
} else if (ps_flags & B43_PS_ASLEEP) { |
| 1167 |
awake = false; |
| 1168 |
} else { |
| 1169 |
//TODO: If the device is awake or this is an AP, or we are scanning, or FIXME, |
| 1170 |
// or we are associated, or FIXME, or the latest PS-Poll packet sent was |
| 1171 |
// successful, set bit26 |
| 1172 |
} |
| 1173 |
|
| 1174 |
/* FIXME: For now we force awake-on and hwps-off */ |
| 1175 |
hwps = false; |
| 1176 |
awake = true; |
| 1177 |
|
| 1178 |
macctl = b43_read32(dev, B43_MMIO_MACCTL); |
| 1179 |
if (hwps) |
| 1180 |
macctl |= B43_MACCTL_HWPS; |
| 1181 |
else |
| 1182 |
macctl &= ~B43_MACCTL_HWPS; |
| 1183 |
if (awake) |
| 1184 |
macctl |= B43_MACCTL_AWAKE; |
| 1185 |
else |
| 1186 |
macctl &= ~B43_MACCTL_AWAKE; |
| 1187 |
b43_write32(dev, B43_MMIO_MACCTL, macctl); |
| 1188 |
/* Commit write */ |
| 1189 |
b43_read32(dev, B43_MMIO_MACCTL); |
| 1190 |
if (awake && dev->dev->core_rev >= 5) { |
| 1191 |
/* Wait for the microcode to wake up. */ |
| 1192 |
for (i = 0; i < 100; i++) { |
| 1193 |
ucstat = b43_shm_read16(dev, B43_SHM_SHARED, |
| 1194 |
B43_SHM_SH_UCODESTAT); |
| 1195 |
if (ucstat != B43_SHM_SH_UCODESTAT_SLEEP) |
| 1196 |
break; |
| 1197 |
udelay(10); |
| 1198 |
} |
| 1199 |
} |
| 1200 |
} |
| 1201 |
|
| 1202 |
/* https://bcm-v4.sipsolutions.net/802.11/PHY/BmacCorePllReset */ |
| 1203 |
void b43_wireless_core_phy_pll_reset(struct b43_wldev *dev) |
| 1204 |
{ |
| 1205 |
struct bcma_drv_cc *bcma_cc __maybe_unused; |
| 1206 |
struct ssb_chipcommon *ssb_cc __maybe_unused; |
| 1207 |
|
| 1208 |
switch (dev->dev->bus_type) { |
| 1209 |
#ifdef CONFIG_B43_BCMA |
| 1210 |
case B43_BUS_BCMA: |
| 1211 |
bcma_cc = &dev->dev->bdev->bus->drv_cc; |
| 1212 |
|
| 1213 |
bcma_cc_write32(bcma_cc, BCMA_CC_PMU_CHIPCTL_ADDR, 0); |
| 1214 |
bcma_cc_mask32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, ~0x4); |
| 1215 |
bcma_cc_set32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, 0x4); |
| 1216 |
bcma_cc_mask32(bcma_cc, BCMA_CC_PMU_CHIPCTL_DATA, ~0x4); |
| 1217 |
break; |
| 1218 |
#endif |
| 1219 |
#ifdef CONFIG_B43_SSB |
| 1220 |
case B43_BUS_SSB: |
| 1221 |
ssb_cc = &dev->dev->sdev->bus->chipco; |
| 1222 |
|
| 1223 |
chipco_write32(ssb_cc, SSB_CHIPCO_CHIPCTL_ADDR, 0); |
| 1224 |
chipco_mask32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, ~0x4); |
| 1225 |
chipco_set32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, 0x4); |
| 1226 |
chipco_mask32(ssb_cc, SSB_CHIPCO_CHIPCTL_DATA, ~0x4); |
| 1227 |
break; |
| 1228 |
#endif |
| 1229 |
} |
| 1230 |
} |
| 1231 |
|
| 1232 |
#ifdef CONFIG_B43_BCMA |
| 1233 |
static void b43_bcma_phy_reset(struct b43_wldev *dev) |
| 1234 |
{ |
| 1235 |
u32 flags; |
| 1236 |
|
| 1237 |
/* Put PHY into reset */ |
| 1238 |
flags = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); |
| 1239 |
flags |= B43_BCMA_IOCTL_PHY_RESET; |
| 1240 |
flags |= B43_BCMA_IOCTL_PHY_BW_20MHZ; /* Make 20 MHz def */ |
| 1241 |
bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, flags); |
| 1242 |
udelay(2); |
| 1243 |
|
| 1244 |
b43_phy_take_out_of_reset(dev); |
| 1245 |
} |
| 1246 |
|
| 1247 |
static void b43_bcma_wireless_core_reset(struct b43_wldev *dev, bool gmode) |
| 1248 |
{ |
| 1249 |
u32 req = B43_BCMA_CLKCTLST_80211_PLL_REQ | |
| 1250 |
B43_BCMA_CLKCTLST_PHY_PLL_REQ; |
| 1251 |
u32 status = B43_BCMA_CLKCTLST_80211_PLL_ST | |
| 1252 |
B43_BCMA_CLKCTLST_PHY_PLL_ST; |
| 1253 |
u32 flags; |
| 1254 |
|
| 1255 |
flags = B43_BCMA_IOCTL_PHY_CLKEN; |
| 1256 |
if (gmode) |
| 1257 |
flags |= B43_BCMA_IOCTL_GMODE; |
| 1258 |
b43_device_enable(dev, flags); |
| 1259 |
|
| 1260 |
if (dev->phy.type == B43_PHYTYPE_AC) { |
| 1261 |
u16 tmp; |
| 1262 |
|
| 1263 |
tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); |
| 1264 |
tmp &= ~B43_BCMA_IOCTL_DAC; |
| 1265 |
tmp |= 0x100; |
| 1266 |
bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); |
| 1267 |
|
| 1268 |
tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); |
| 1269 |
tmp &= ~B43_BCMA_IOCTL_PHY_CLKEN; |
| 1270 |
bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); |
| 1271 |
|
| 1272 |
tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); |
| 1273 |
tmp |= B43_BCMA_IOCTL_PHY_CLKEN; |
| 1274 |
bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); |
| 1275 |
} |
| 1276 |
|
| 1277 |
bcma_core_set_clockmode(dev->dev->bdev, BCMA_CLKMODE_FAST); |
| 1278 |
b43_bcma_phy_reset(dev); |
| 1279 |
bcma_core_pll_ctl(dev->dev->bdev, req, status, true); |
| 1280 |
} |
| 1281 |
#endif |
| 1282 |
|
| 1283 |
#ifdef CONFIG_B43_SSB |
| 1284 |
static void b43_ssb_wireless_core_reset(struct b43_wldev *dev, bool gmode) |
| 1285 |
{ |
| 1286 |
u32 flags = 0; |
| 1287 |
|
| 1288 |
if (gmode) |
| 1289 |
flags |= B43_TMSLOW_GMODE; |
| 1290 |
flags |= B43_TMSLOW_PHYCLKEN; |
| 1291 |
flags |= B43_TMSLOW_PHYRESET; |
| 1292 |
if (dev->phy.type == B43_PHYTYPE_N) |
| 1293 |
flags |= B43_TMSLOW_PHY_BANDWIDTH_20MHZ; /* Make 20 MHz def */ |
| 1294 |
b43_device_enable(dev, flags); |
| 1295 |
msleep(2); /* Wait for the PLL to turn on. */ |
| 1296 |
|
| 1297 |
b43_phy_take_out_of_reset(dev); |
| 1298 |
} |
| 1299 |
#endif |
| 1300 |
|
| 1301 |
void b43_wireless_core_reset(struct b43_wldev *dev, bool gmode) |
| 1302 |
{ |
| 1303 |
u32 macctl; |
| 1304 |
|
| 1305 |
switch (dev->dev->bus_type) { |
| 1306 |
#ifdef CONFIG_B43_BCMA |
| 1307 |
case B43_BUS_BCMA: |
| 1308 |
b43_bcma_wireless_core_reset(dev, gmode); |
| 1309 |
break; |
| 1310 |
#endif |
| 1311 |
#ifdef CONFIG_B43_SSB |
| 1312 |
case B43_BUS_SSB: |
| 1313 |
b43_ssb_wireless_core_reset(dev, gmode); |
| 1314 |
break; |
| 1315 |
#endif |
| 1316 |
} |
| 1317 |
|
| 1318 |
/* Turn Analog ON, but only if we already know the PHY-type. |
| 1319 |
* This protects against very early setup where we don't know the |
| 1320 |
* PHY-type, yet. wireless_core_reset will be called once again later, |
| 1321 |
* when we know the PHY-type. */ |
| 1322 |
if (dev->phy.ops) |
| 1323 |
dev->phy.ops->switch_analog(dev, 1); |
| 1324 |
|
| 1325 |
macctl = b43_read32(dev, B43_MMIO_MACCTL); |
| 1326 |
macctl &= ~B43_MACCTL_GMODE; |
| 1327 |
if (gmode) |
| 1328 |
macctl |= B43_MACCTL_GMODE; |
| 1329 |
macctl |= B43_MACCTL_IHR_ENABLED; |
| 1330 |
b43_write32(dev, B43_MMIO_MACCTL, macctl); |
| 1331 |
} |
| 1332 |
|
| 1333 |
static void handle_irq_transmit_status(struct b43_wldev *dev) |
| 1334 |
{ |
| 1335 |
u32 v0, v1; |
| 1336 |
u16 tmp; |
| 1337 |
struct b43_txstatus stat; |
| 1338 |
|
| 1339 |
while (1) { |
| 1340 |
v0 = b43_read32(dev, B43_MMIO_XMITSTAT_0); |
| 1341 |
if (!(v0 & 0x00000001)) |
| 1342 |
break; |
| 1343 |
v1 = b43_read32(dev, B43_MMIO_XMITSTAT_1); |
| 1344 |
|
| 1345 |
stat.cookie = (v0 >> 16); |
| 1346 |
stat.seq = (v1 & 0x0000FFFF); |
| 1347 |
stat.phy_stat = ((v1 & 0x00FF0000) >> 16); |
| 1348 |
tmp = (v0 & 0x0000FFFF); |
| 1349 |
stat.frame_count = ((tmp & 0xF000) >> 12); |
| 1350 |
stat.rts_count = ((tmp & 0x0F00) >> 8); |
| 1351 |
stat.supp_reason = ((tmp & 0x001C) >> 2); |
| 1352 |
stat.pm_indicated = !!(tmp & 0x0080); |
| 1353 |
stat.intermediate = !!(tmp & 0x0040); |
| 1354 |
stat.for_ampdu = !!(tmp & 0x0020); |
| 1355 |
stat.acked = !!(tmp & 0x0002); |
| 1356 |
|
| 1357 |
b43_handle_txstatus(dev, &stat); |
| 1358 |
} |
| 1359 |
} |
| 1360 |
|
| 1361 |
static void drain_txstatus_queue(struct b43_wldev *dev) |
| 1362 |
{ |
| 1363 |
u32 dummy; |
| 1364 |
|
| 1365 |
if (dev->dev->core_rev < 5) |
| 1366 |
return; |
| 1367 |
/* Read all entries from the microcode TXstatus FIFO |
| 1368 |
* and throw them away. |
| 1369 |
*/ |
| 1370 |
while (1) { |
| 1371 |
dummy = b43_read32(dev, B43_MMIO_XMITSTAT_0); |
| 1372 |
if (!(dummy & 0x00000001)) |
| 1373 |
break; |
| 1374 |
dummy = b43_read32(dev, B43_MMIO_XMITSTAT_1); |
| 1375 |
} |
| 1376 |
} |
| 1377 |
|
| 1378 |
static u32 b43_jssi_read(struct b43_wldev *dev) |
| 1379 |
{ |
| 1380 |
u32 val = 0; |
| 1381 |
|
| 1382 |
val = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI1); |
| 1383 |
val <<= 16; |
| 1384 |
val |= b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI0); |
| 1385 |
|
| 1386 |
return val; |
| 1387 |
} |
| 1388 |
|
| 1389 |
static void b43_jssi_write(struct b43_wldev *dev, u32 jssi) |
| 1390 |
{ |
| 1391 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI0, |
| 1392 |
(jssi & 0x0000FFFF)); |
| 1393 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_JSSI1, |
| 1394 |
(jssi & 0xFFFF0000) >> 16); |
| 1395 |
} |
| 1396 |
|
| 1397 |
static void b43_generate_noise_sample(struct b43_wldev *dev) |
| 1398 |
{ |
| 1399 |
b43_jssi_write(dev, 0x7F7F7F7F); |
| 1400 |
b43_write32(dev, B43_MMIO_MACCMD, |
| 1401 |
b43_read32(dev, B43_MMIO_MACCMD) | B43_MACCMD_BGNOISE); |
| 1402 |
} |
| 1403 |
|
| 1404 |
static void b43_calculate_link_quality(struct b43_wldev *dev) |
| 1405 |
{ |
| 1406 |
/* Top half of Link Quality calculation. */ |
| 1407 |
|
| 1408 |
if (dev->phy.type != B43_PHYTYPE_G) |
| 1409 |
return; |
| 1410 |
if (dev->noisecalc.calculation_running) |
| 1411 |
return; |
| 1412 |
dev->noisecalc.calculation_running = true; |
| 1413 |
dev->noisecalc.nr_samples = 0; |
| 1414 |
|
| 1415 |
b43_generate_noise_sample(dev); |
| 1416 |
} |
| 1417 |
|
| 1418 |
static void handle_irq_noise(struct b43_wldev *dev) |
| 1419 |
{ |
| 1420 |
struct b43_phy_g *phy = dev->phy.g; |
| 1421 |
u16 tmp; |
| 1422 |
u8 noise[4]; |
| 1423 |
u8 i, j; |
| 1424 |
s32 average; |
| 1425 |
|
| 1426 |
/* Bottom half of Link Quality calculation. */ |
| 1427 |
|
| 1428 |
if (dev->phy.type != B43_PHYTYPE_G) |
| 1429 |
return; |
| 1430 |
|
| 1431 |
/* Possible race condition: It might be possible that the user |
| 1432 |
* changed to a different channel in the meantime since we |
| 1433 |
* started the calculation. We ignore that fact, since it's |
| 1434 |
* not really that much of a problem. The background noise is |
| 1435 |
* an estimation only anyway. Slightly wrong results will get damped |
| 1436 |
* by the averaging of the 8 sample rounds. Additionally the |
| 1437 |
* value is shortlived. So it will be replaced by the next noise |
| 1438 |
* calculation round soon. */ |
| 1439 |
|
| 1440 |
B43_WARN_ON(!dev->noisecalc.calculation_running); |
| 1441 |
*((__le32 *)noise) = cpu_to_le32(b43_jssi_read(dev)); |
| 1442 |
if (noise[0] == 0x7F || noise[1] == 0x7F || |
| 1443 |
noise[2] == 0x7F || noise[3] == 0x7F) |
| 1444 |
goto generate_new; |
| 1445 |
|
| 1446 |
/* Get the noise samples. */ |
| 1447 |
B43_WARN_ON(dev->noisecalc.nr_samples >= 8); |
| 1448 |
i = dev->noisecalc.nr_samples; |
| 1449 |
noise[0] = clamp_val(noise[0], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); |
| 1450 |
noise[1] = clamp_val(noise[1], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); |
| 1451 |
noise[2] = clamp_val(noise[2], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); |
| 1452 |
noise[3] = clamp_val(noise[3], 0, ARRAY_SIZE(phy->nrssi_lt) - 1); |
| 1453 |
dev->noisecalc.samples[i][0] = phy->nrssi_lt[noise[0]]; |
| 1454 |
dev->noisecalc.samples[i][1] = phy->nrssi_lt[noise[1]]; |
| 1455 |
dev->noisecalc.samples[i][2] = phy->nrssi_lt[noise[2]]; |
| 1456 |
dev->noisecalc.samples[i][3] = phy->nrssi_lt[noise[3]]; |
| 1457 |
dev->noisecalc.nr_samples++; |
| 1458 |
if (dev->noisecalc.nr_samples == 8) { |
| 1459 |
/* Calculate the Link Quality by the noise samples. */ |
| 1460 |
average = 0; |
| 1461 |
for (i = 0; i < 8; i++) { |
| 1462 |
for (j = 0; j < 4; j++) |
| 1463 |
average += dev->noisecalc.samples[i][j]; |
| 1464 |
} |
| 1465 |
average /= (8 * 4); |
| 1466 |
average *= 125; |
| 1467 |
average += 64; |
| 1468 |
average /= 128; |
| 1469 |
tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x40C); |
| 1470 |
tmp = (tmp / 128) & 0x1F; |
| 1471 |
if (tmp >= 8) |
| 1472 |
average += 2; |
| 1473 |
else |
| 1474 |
average -= 25; |
| 1475 |
if (tmp == 8) |
| 1476 |
average -= 72; |
| 1477 |
else |
| 1478 |
average -= 48; |
| 1479 |
|
| 1480 |
dev->stats.link_noise = average; |
| 1481 |
dev->noisecalc.calculation_running = false; |
| 1482 |
return; |
| 1483 |
} |
| 1484 |
generate_new: |
| 1485 |
b43_generate_noise_sample(dev); |
| 1486 |
} |
| 1487 |
|
| 1488 |
static void handle_irq_tbtt_indication(struct b43_wldev *dev) |
| 1489 |
{ |
| 1490 |
if (b43_is_mode(dev->wl, NL80211_IFTYPE_AP)) { |
| 1491 |
///TODO: PS TBTT |
| 1492 |
} else { |
| 1493 |
if (1 /*FIXME: the last PSpoll frame was sent successfully */ ) |
| 1494 |
b43_power_saving_ctl_bits(dev, 0); |
| 1495 |
} |
| 1496 |
if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC)) |
| 1497 |
dev->dfq_valid = true; |
| 1498 |
} |
| 1499 |
|
| 1500 |
static void handle_irq_atim_end(struct b43_wldev *dev) |
| 1501 |
{ |
| 1502 |
if (dev->dfq_valid) { |
| 1503 |
b43_write32(dev, B43_MMIO_MACCMD, |
| 1504 |
b43_read32(dev, B43_MMIO_MACCMD) |
| 1505 |
| B43_MACCMD_DFQ_VALID); |
| 1506 |
dev->dfq_valid = false; |
| 1507 |
} |
| 1508 |
} |
| 1509 |
|
| 1510 |
static void handle_irq_pmq(struct b43_wldev *dev) |
| 1511 |
{ |
| 1512 |
u32 tmp; |
| 1513 |
|
| 1514 |
//TODO: AP mode. |
| 1515 |
|
| 1516 |
while (1) { |
| 1517 |
tmp = b43_read32(dev, B43_MMIO_PS_STATUS); |
| 1518 |
if (!(tmp & 0x00000008)) |
| 1519 |
break; |
| 1520 |
} |
| 1521 |
/* 16bit write is odd, but correct. */ |
| 1522 |
b43_write16(dev, B43_MMIO_PS_STATUS, 0x0002); |
| 1523 |
} |
| 1524 |
|
| 1525 |
static void b43_write_template_common(struct b43_wldev *dev, |
| 1526 |
const u8 *data, u16 size, |
| 1527 |
u16 ram_offset, |
| 1528 |
u16 shm_size_offset, u8 rate) |
| 1529 |
{ |
| 1530 |
u32 i, tmp; |
| 1531 |
struct b43_plcp_hdr4 plcp; |
| 1532 |
|
| 1533 |
plcp.data = 0; |
| 1534 |
b43_generate_plcp_hdr(&plcp, size + FCS_LEN, rate); |
| 1535 |
b43_ram_write(dev, ram_offset, le32_to_cpu(plcp.data)); |
| 1536 |
ram_offset += sizeof(u32); |
| 1537 |
/* The PLCP is 6 bytes long, but we only wrote 4 bytes, yet. |
| 1538 |
* So leave the first two bytes of the next write blank. |
| 1539 |
*/ |
| 1540 |
tmp = (u32) (data[0]) << 16; |
| 1541 |
tmp |= (u32) (data[1]) << 24; |
| 1542 |
b43_ram_write(dev, ram_offset, tmp); |
| 1543 |
ram_offset += sizeof(u32); |
| 1544 |
for (i = 2; i < size; i += sizeof(u32)) { |
| 1545 |
tmp = (u32) (data[i + 0]); |
| 1546 |
if (i + 1 < size) |
| 1547 |
tmp |= (u32) (data[i + 1]) << 8; |
| 1548 |
if (i + 2 < size) |
| 1549 |
tmp |= (u32) (data[i + 2]) << 16; |
| 1550 |
if (i + 3 < size) |
| 1551 |
tmp |= (u32) (data[i + 3]) << 24; |
| 1552 |
b43_ram_write(dev, ram_offset + i - 2, tmp); |
| 1553 |
} |
| 1554 |
b43_shm_write16(dev, B43_SHM_SHARED, shm_size_offset, |
| 1555 |
size + sizeof(struct b43_plcp_hdr6)); |
| 1556 |
} |
| 1557 |
|
| 1558 |
/* Check if the use of the antenna that ieee80211 told us to |
| 1559 |
* use is possible. This will fall back to DEFAULT. |
| 1560 |
* "antenna_nr" is the antenna identifier we got from ieee80211. */ |
| 1561 |
u8 b43_ieee80211_antenna_sanitize(struct b43_wldev *dev, |
| 1562 |
u8 antenna_nr) |
| 1563 |
{ |
| 1564 |
u8 antenna_mask; |
| 1565 |
|
| 1566 |
if (antenna_nr == 0) { |
| 1567 |
/* Zero means "use default antenna". That's always OK. */ |
| 1568 |
return 0; |
| 1569 |
} |
| 1570 |
|
| 1571 |
/* Get the mask of available antennas. */ |
| 1572 |
if (dev->phy.gmode) |
| 1573 |
antenna_mask = dev->dev->bus_sprom->ant_available_bg; |
| 1574 |
else |
| 1575 |
antenna_mask = dev->dev->bus_sprom->ant_available_a; |
| 1576 |
|
| 1577 |
if (!(antenna_mask & (1 << (antenna_nr - 1)))) { |
| 1578 |
/* This antenna is not available. Fall back to default. */ |
| 1579 |
return 0; |
| 1580 |
} |
| 1581 |
|
| 1582 |
return antenna_nr; |
| 1583 |
} |
| 1584 |
|
| 1585 |
/* Convert a b43 antenna number value to the PHY TX control value. */ |
| 1586 |
static u16 b43_antenna_to_phyctl(int antenna) |
| 1587 |
{ |
| 1588 |
switch (antenna) { |
| 1589 |
case B43_ANTENNA0: |
| 1590 |
return B43_TXH_PHY_ANT0; |
| 1591 |
case B43_ANTENNA1: |
| 1592 |
return B43_TXH_PHY_ANT1; |
| 1593 |
case B43_ANTENNA2: |
| 1594 |
return B43_TXH_PHY_ANT2; |
| 1595 |
case B43_ANTENNA3: |
| 1596 |
return B43_TXH_PHY_ANT3; |
| 1597 |
case B43_ANTENNA_AUTO0: |
| 1598 |
case B43_ANTENNA_AUTO1: |
| 1599 |
return B43_TXH_PHY_ANT01AUTO; |
| 1600 |
} |
| 1601 |
B43_WARN_ON(1); |
| 1602 |
return 0; |
| 1603 |
} |
| 1604 |
|
| 1605 |
static void b43_write_beacon_template(struct b43_wldev *dev, |
| 1606 |
u16 ram_offset, |
| 1607 |
u16 shm_size_offset) |
| 1608 |
{ |
| 1609 |
unsigned int i, len, variable_len; |
| 1610 |
const struct ieee80211_mgmt *bcn; |
| 1611 |
const u8 *ie; |
| 1612 |
bool tim_found = false; |
| 1613 |
unsigned int rate; |
| 1614 |
u16 ctl; |
| 1615 |
int antenna; |
| 1616 |
struct ieee80211_tx_info *info; |
| 1617 |
unsigned long flags; |
| 1618 |
struct sk_buff *beacon_skb; |
| 1619 |
|
| 1620 |
spin_lock_irqsave(&dev->wl->beacon_lock, flags); |
| 1621 |
info = IEEE80211_SKB_CB(dev->wl->current_beacon); |
| 1622 |
rate = ieee80211_get_tx_rate(dev->wl->hw, info)->hw_value; |
| 1623 |
/* Clone the beacon, so it cannot go away, while we write it to hw. */ |
| 1624 |
beacon_skb = skb_clone(dev->wl->current_beacon, GFP_ATOMIC); |
| 1625 |
spin_unlock_irqrestore(&dev->wl->beacon_lock, flags); |
| 1626 |
|
| 1627 |
if (!beacon_skb) { |
| 1628 |
b43dbg(dev->wl, "Could not upload beacon. " |
| 1629 |
"Failed to clone beacon skb."); |
| 1630 |
return; |
| 1631 |
} |
| 1632 |
|
| 1633 |
bcn = (const struct ieee80211_mgmt *)(beacon_skb->data); |
| 1634 |
len = min_t(size_t, beacon_skb->len, |
| 1635 |
0x200 - sizeof(struct b43_plcp_hdr6)); |
| 1636 |
|
| 1637 |
b43_write_template_common(dev, (const u8 *)bcn, |
| 1638 |
len, ram_offset, shm_size_offset, rate); |
| 1639 |
|
| 1640 |
/* Write the PHY TX control parameters. */ |
| 1641 |
antenna = B43_ANTENNA_DEFAULT; |
| 1642 |
antenna = b43_antenna_to_phyctl(antenna); |
| 1643 |
ctl = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL); |
| 1644 |
/* We can't send beacons with short preamble. Would get PHY errors. */ |
| 1645 |
ctl &= ~B43_TXH_PHY_SHORTPRMBL; |
| 1646 |
ctl &= ~B43_TXH_PHY_ANT; |
| 1647 |
ctl &= ~B43_TXH_PHY_ENC; |
| 1648 |
ctl |= antenna; |
| 1649 |
if (b43_is_cck_rate(rate)) |
| 1650 |
ctl |= B43_TXH_PHY_ENC_CCK; |
| 1651 |
else |
| 1652 |
ctl |= B43_TXH_PHY_ENC_OFDM; |
| 1653 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL, ctl); |
| 1654 |
|
| 1655 |
/* Find the position of the TIM and the DTIM_period value |
| 1656 |
* and write them to SHM. */ |
| 1657 |
ie = bcn->u.beacon.variable; |
| 1658 |
variable_len = len - offsetof(struct ieee80211_mgmt, u.beacon.variable); |
| 1659 |
for (i = 0; i < variable_len - 2; ) { |
| 1660 |
uint8_t ie_id, ie_len; |
| 1661 |
|
| 1662 |
ie_id = ie[i]; |
| 1663 |
ie_len = ie[i + 1]; |
| 1664 |
if (ie_id == 5) { |
| 1665 |
u16 tim_position; |
| 1666 |
u16 dtim_period; |
| 1667 |
/* This is the TIM Information Element */ |
| 1668 |
|
| 1669 |
/* Check whether the ie_len is in the beacon data range. */ |
| 1670 |
if (variable_len < ie_len + 2 + i) |
| 1671 |
break; |
| 1672 |
/* A valid TIM is at least 4 bytes long. */ |
| 1673 |
if (ie_len < 4) |
| 1674 |
break; |
| 1675 |
tim_found = true; |
| 1676 |
|
| 1677 |
tim_position = sizeof(struct b43_plcp_hdr6); |
| 1678 |
tim_position += offsetof(struct ieee80211_mgmt, u.beacon.variable); |
| 1679 |
tim_position += i; |
| 1680 |
|
| 1681 |
dtim_period = ie[i + 3]; |
| 1682 |
|
| 1683 |
b43_shm_write16(dev, B43_SHM_SHARED, |
| 1684 |
B43_SHM_SH_TIMBPOS, tim_position); |
| 1685 |
b43_shm_write16(dev, B43_SHM_SHARED, |
| 1686 |
B43_SHM_SH_DTIMPER, dtim_period); |
| 1687 |
break; |
| 1688 |
} |
| 1689 |
i += ie_len + 2; |
| 1690 |
} |
| 1691 |
if (!tim_found) { |
| 1692 |
/* |
| 1693 |
* If ucode wants to modify TIM do it behind the beacon, this |
| 1694 |
* will happen, for example, when doing mesh networking. |
| 1695 |
*/ |
| 1696 |
b43_shm_write16(dev, B43_SHM_SHARED, |
| 1697 |
B43_SHM_SH_TIMBPOS, |
| 1698 |
len + sizeof(struct b43_plcp_hdr6)); |
| 1699 |
b43_shm_write16(dev, B43_SHM_SHARED, |
| 1700 |
B43_SHM_SH_DTIMPER, 0); |
| 1701 |
} |
| 1702 |
b43dbg(dev->wl, "Updated beacon template at 0x%x\n", ram_offset); |
| 1703 |
|
| 1704 |
dev_kfree_skb_any(beacon_skb); |
| 1705 |
} |
| 1706 |
|
| 1707 |
static void b43_upload_beacon0(struct b43_wldev *dev) |
| 1708 |
{ |
| 1709 |
struct b43_wl *wl = dev->wl; |
| 1710 |
|
| 1711 |
if (wl->beacon0_uploaded) |
| 1712 |
return; |
| 1713 |
b43_write_beacon_template(dev, B43_SHM_SH_BT_BASE0, B43_SHM_SH_BTL0); |
| 1714 |
wl->beacon0_uploaded = true; |
| 1715 |
} |
| 1716 |
|
| 1717 |
static void b43_upload_beacon1(struct b43_wldev *dev) |
| 1718 |
{ |
| 1719 |
struct b43_wl *wl = dev->wl; |
| 1720 |
|
| 1721 |
if (wl->beacon1_uploaded) |
| 1722 |
return; |
| 1723 |
b43_write_beacon_template(dev, B43_SHM_SH_BT_BASE1, B43_SHM_SH_BTL1); |
| 1724 |
wl->beacon1_uploaded = true; |
| 1725 |
} |
| 1726 |
|
| 1727 |
static void handle_irq_beacon(struct b43_wldev *dev) |
| 1728 |
{ |
| 1729 |
struct b43_wl *wl = dev->wl; |
| 1730 |
u32 cmd, beacon0_valid, beacon1_valid; |
| 1731 |
|
| 1732 |
if (!b43_is_mode(wl, NL80211_IFTYPE_AP) && |
| 1733 |
!b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) && |
| 1734 |
!b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) |
| 1735 |
return; |
| 1736 |
|
| 1737 |
/* This is the bottom half of the asynchronous beacon update. */ |
| 1738 |
|
| 1739 |
/* Ignore interrupt in the future. */ |
| 1740 |
dev->irq_mask &= ~B43_IRQ_BEACON; |
| 1741 |
|
| 1742 |
cmd = b43_read32(dev, B43_MMIO_MACCMD); |
| 1743 |
beacon0_valid = (cmd & B43_MACCMD_BEACON0_VALID); |
| 1744 |
beacon1_valid = (cmd & B43_MACCMD_BEACON1_VALID); |
| 1745 |
|
| 1746 |
/* Schedule interrupt manually, if busy. */ |
| 1747 |
if (beacon0_valid && beacon1_valid) { |
| 1748 |
b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, B43_IRQ_BEACON); |
| 1749 |
dev->irq_mask |= B43_IRQ_BEACON; |
| 1750 |
return; |
| 1751 |
} |
| 1752 |
|
| 1753 |
if (unlikely(wl->beacon_templates_virgin)) { |
| 1754 |
/* We never uploaded a beacon before. |
| 1755 |
* Upload both templates now, but only mark one valid. */ |
| 1756 |
wl->beacon_templates_virgin = false; |
| 1757 |
b43_upload_beacon0(dev); |
| 1758 |
b43_upload_beacon1(dev); |
| 1759 |
cmd = b43_read32(dev, B43_MMIO_MACCMD); |
| 1760 |
cmd |= B43_MACCMD_BEACON0_VALID; |
| 1761 |
b43_write32(dev, B43_MMIO_MACCMD, cmd); |
| 1762 |
} else { |
| 1763 |
if (!beacon0_valid) { |
| 1764 |
b43_upload_beacon0(dev); |
| 1765 |
cmd = b43_read32(dev, B43_MMIO_MACCMD); |
| 1766 |
cmd |= B43_MACCMD_BEACON0_VALID; |
| 1767 |
b43_write32(dev, B43_MMIO_MACCMD, cmd); |
| 1768 |
} else if (!beacon1_valid) { |
| 1769 |
b43_upload_beacon1(dev); |
| 1770 |
cmd = b43_read32(dev, B43_MMIO_MACCMD); |
| 1771 |
cmd |= B43_MACCMD_BEACON1_VALID; |
| 1772 |
b43_write32(dev, B43_MMIO_MACCMD, cmd); |
| 1773 |
} |
| 1774 |
} |
| 1775 |
} |
| 1776 |
|
| 1777 |
static void b43_do_beacon_update_trigger_work(struct b43_wldev *dev) |
| 1778 |
{ |
| 1779 |
u32 old_irq_mask = dev->irq_mask; |
| 1780 |
|
| 1781 |
/* update beacon right away or defer to irq */ |
| 1782 |
handle_irq_beacon(dev); |
| 1783 |
if (old_irq_mask != dev->irq_mask) { |
| 1784 |
/* The handler updated the IRQ mask. */ |
| 1785 |
B43_WARN_ON(!dev->irq_mask); |
| 1786 |
if (b43_read32(dev, B43_MMIO_GEN_IRQ_MASK)) { |
| 1787 |
b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); |
| 1788 |
} else { |
| 1789 |
/* Device interrupts are currently disabled. That means |
| 1790 |
* we just ran the hardirq handler and scheduled the |
| 1791 |
* IRQ thread. The thread will write the IRQ mask when |
| 1792 |
* it finished, so there's nothing to do here. Writing |
| 1793 |
* the mask _here_ would incorrectly re-enable IRQs. */ |
| 1794 |
} |
| 1795 |
} |
| 1796 |
} |
| 1797 |
|
| 1798 |
static void b43_beacon_update_trigger_work(struct work_struct *work) |
| 1799 |
{ |
| 1800 |
struct b43_wl *wl = container_of(work, struct b43_wl, |
| 1801 |
beacon_update_trigger); |
| 1802 |
struct b43_wldev *dev; |
| 1803 |
|
| 1804 |
mutex_lock(&wl->mutex); |
| 1805 |
dev = wl->current_dev; |
| 1806 |
if (likely(dev && (b43_status(dev) >= B43_STAT_INITIALIZED))) { |
| 1807 |
if (b43_bus_host_is_sdio(dev->dev)) { |
| 1808 |
/* wl->mutex is enough. */ |
| 1809 |
b43_do_beacon_update_trigger_work(dev); |
| 1810 |
} else { |
| 1811 |
spin_lock_irq(&wl->hardirq_lock); |
| 1812 |
b43_do_beacon_update_trigger_work(dev); |
| 1813 |
spin_unlock_irq(&wl->hardirq_lock); |
| 1814 |
} |
| 1815 |
} |
| 1816 |
mutex_unlock(&wl->mutex); |
| 1817 |
} |
| 1818 |
|
| 1819 |
/* Asynchronously update the packet templates in template RAM. */ |
| 1820 |
static void b43_update_templates(struct b43_wl *wl) |
| 1821 |
{ |
| 1822 |
struct sk_buff *beacon, *old_beacon; |
| 1823 |
unsigned long flags; |
| 1824 |
|
| 1825 |
/* This is the top half of the asynchronous beacon update. |
| 1826 |
* The bottom half is the beacon IRQ. |
| 1827 |
* Beacon update must be asynchronous to avoid sending an |
| 1828 |
* invalid beacon. This can happen for example, if the firmware |
| 1829 |
* transmits a beacon while we are updating it. */ |
| 1830 |
|
| 1831 |
/* We could modify the existing beacon and set the aid bit in |
| 1832 |
* the TIM field, but that would probably require resizing and |
| 1833 |
* moving of data within the beacon template. |
| 1834 |
* Simply request a new beacon and let mac80211 do the hard work. */ |
| 1835 |
beacon = ieee80211_beacon_get(wl->hw, wl->vif, 0); |
| 1836 |
if (unlikely(!beacon)) |
| 1837 |
return; |
| 1838 |
|
| 1839 |
spin_lock_irqsave(&wl->beacon_lock, flags); |
| 1840 |
old_beacon = wl->current_beacon; |
| 1841 |
wl->current_beacon = beacon; |
| 1842 |
wl->beacon0_uploaded = false; |
| 1843 |
wl->beacon1_uploaded = false; |
| 1844 |
spin_unlock_irqrestore(&wl->beacon_lock, flags); |
| 1845 |
|
| 1846 |
ieee80211_queue_work(wl->hw, &wl->beacon_update_trigger); |
| 1847 |
|
| 1848 |
if (old_beacon) |
| 1849 |
dev_kfree_skb_any(old_beacon); |
| 1850 |
} |
| 1851 |
|
| 1852 |
static void b43_set_beacon_int(struct b43_wldev *dev, u16 beacon_int) |
| 1853 |
{ |
| 1854 |
b43_time_lock(dev); |
| 1855 |
if (dev->dev->core_rev >= 3) { |
| 1856 |
b43_write32(dev, B43_MMIO_TSF_CFP_REP, (beacon_int << 16)); |
| 1857 |
b43_write32(dev, B43_MMIO_TSF_CFP_START, (beacon_int << 10)); |
| 1858 |
} else { |
| 1859 |
b43_write16(dev, 0x606, (beacon_int >> 6)); |
| 1860 |
b43_write16(dev, 0x610, beacon_int); |
| 1861 |
} |
| 1862 |
b43_time_unlock(dev); |
| 1863 |
b43dbg(dev->wl, "Set beacon interval to %u\n", beacon_int); |
| 1864 |
} |
| 1865 |
|
| 1866 |
static void b43_handle_firmware_panic(struct b43_wldev *dev) |
| 1867 |
{ |
| 1868 |
u16 reason; |
| 1869 |
|
| 1870 |
/* Read the register that contains the reason code for the panic. */ |
| 1871 |
reason = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_FWPANIC_REASON_REG); |
| 1872 |
b43err(dev->wl, "Whoopsy, firmware panic! Reason: %u\n", reason); |
| 1873 |
|
| 1874 |
switch (reason) { |
| 1875 |
default: |
| 1876 |
b43dbg(dev->wl, "The panic reason is unknown.\n"); |
| 1877 |
fallthrough; |
| 1878 |
case B43_FWPANIC_DIE: |
| 1879 |
/* Do not restart the controller or firmware. |
| 1880 |
* The device is nonfunctional from now on. |
| 1881 |
* Restarting would result in this panic to trigger again, |
| 1882 |
* so we avoid that recursion. */ |
| 1883 |
break; |
| 1884 |
case B43_FWPANIC_RESTART: |
| 1885 |
b43_controller_restart(dev, "Microcode panic"); |
| 1886 |
break; |
| 1887 |
} |
| 1888 |
} |
| 1889 |
|
| 1890 |
static void handle_irq_ucode_debug(struct b43_wldev *dev) |
| 1891 |
{ |
| 1892 |
unsigned int i, cnt; |
| 1893 |
u16 reason, marker_id, marker_line; |
| 1894 |
__le16 *buf; |
| 1895 |
|
| 1896 |
/* The proprietary firmware doesn't have this IRQ. */ |
| 1897 |
if (!dev->fw.opensource) |
| 1898 |
return; |
| 1899 |
|
| 1900 |
/* Read the register that contains the reason code for this IRQ. */ |
| 1901 |
reason = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_DEBUGIRQ_REASON_REG); |
| 1902 |
|
| 1903 |
switch (reason) { |
| 1904 |
case B43_DEBUGIRQ_PANIC: |
| 1905 |
b43_handle_firmware_panic(dev); |
| 1906 |
break; |
| 1907 |
case B43_DEBUGIRQ_DUMP_SHM: |
| 1908 |
if (!B43_DEBUG) |
| 1909 |
break; /* Only with driver debugging enabled. */ |
| 1910 |
buf = kmalloc(4096, GFP_ATOMIC); |
| 1911 |
if (!buf) { |
| 1912 |
b43dbg(dev->wl, "SHM-dump: Failed to allocate memory\n"); |
| 1913 |
goto out; |
| 1914 |
} |
| 1915 |
for (i = 0; i < 4096; i += 2) { |
| 1916 |
u16 tmp = b43_shm_read16(dev, B43_SHM_SHARED, i); |
| 1917 |
buf[i / 2] = cpu_to_le16(tmp); |
| 1918 |
} |
| 1919 |
b43info(dev->wl, "Shared memory dump:\n"); |
| 1920 |
print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, |
| 1921 |
16, 2, buf, 4096, 1); |
| 1922 |
kfree(buf); |
| 1923 |
break; |
| 1924 |
case B43_DEBUGIRQ_DUMP_REGS: |
| 1925 |
if (!B43_DEBUG) |
| 1926 |
break; /* Only with driver debugging enabled. */ |
| 1927 |
b43info(dev->wl, "Microcode register dump:\n"); |
| 1928 |
for (i = 0, cnt = 0; i < 64; i++) { |
| 1929 |
u16 tmp = b43_shm_read16(dev, B43_SHM_SCRATCH, i); |
| 1930 |
if (cnt == 0) |
| 1931 |
printk(KERN_INFO); |
| 1932 |
printk("r%02u: 0x%04X ", i, tmp); |
| 1933 |
cnt++; |
| 1934 |
if (cnt == 6) { |
| 1935 |
printk("\n"); |
| 1936 |
cnt = 0; |
| 1937 |
} |
| 1938 |
} |
| 1939 |
printk("\n"); |
| 1940 |
break; |
| 1941 |
case B43_DEBUGIRQ_MARKER: |
| 1942 |
if (!B43_DEBUG) |
| 1943 |
break; /* Only with driver debugging enabled. */ |
| 1944 |
marker_id = b43_shm_read16(dev, B43_SHM_SCRATCH, |
| 1945 |
B43_MARKER_ID_REG); |
| 1946 |
marker_line = b43_shm_read16(dev, B43_SHM_SCRATCH, |
| 1947 |
B43_MARKER_LINE_REG); |
| 1948 |
b43info(dev->wl, "The firmware just executed the MARKER(%u) " |
| 1949 |
"at line number %u\n", |
| 1950 |
marker_id, marker_line); |
| 1951 |
break; |
| 1952 |
default: |
| 1953 |
b43dbg(dev->wl, "Debug-IRQ triggered for unknown reason: %u\n", |
| 1954 |
reason); |
| 1955 |
} |
| 1956 |
out: |
| 1957 |
/* Acknowledge the debug-IRQ, so the firmware can continue. */ |
| 1958 |
b43_shm_write16(dev, B43_SHM_SCRATCH, |
| 1959 |
B43_DEBUGIRQ_REASON_REG, B43_DEBUGIRQ_ACK); |
| 1960 |
} |
| 1961 |
|
| 1962 |
static void b43_do_interrupt_thread(struct b43_wldev *dev) |
| 1963 |
{ |
| 1964 |
u32 reason; |
| 1965 |
u32 dma_reason[ARRAY_SIZE(dev->dma_reason)]; |
| 1966 |
u32 merged_dma_reason = 0; |
| 1967 |
int i; |
| 1968 |
|
| 1969 |
if (unlikely(b43_status(dev) != B43_STAT_STARTED)) |
| 1970 |
return; |
| 1971 |
|
| 1972 |
reason = dev->irq_reason; |
| 1973 |
for (i = 0; i < ARRAY_SIZE(dma_reason); i++) { |
| 1974 |
dma_reason[i] = dev->dma_reason[i]; |
| 1975 |
merged_dma_reason |= dma_reason[i]; |
| 1976 |
} |
| 1977 |
|
| 1978 |
if (unlikely(reason & B43_IRQ_MAC_TXERR)) |
| 1979 |
b43err(dev->wl, "MAC transmission error\n"); |
| 1980 |
|
| 1981 |
if (unlikely(reason & B43_IRQ_PHY_TXERR)) { |
| 1982 |
b43err(dev->wl, "PHY transmission error\n"); |
| 1983 |
rmb(); |
| 1984 |
if (unlikely(atomic_dec_and_test(&dev->phy.txerr_cnt))) { |
| 1985 |
atomic_set(&dev->phy.txerr_cnt, |
| 1986 |
B43_PHY_TX_BADNESS_LIMIT); |
| 1987 |
b43err(dev->wl, "Too many PHY TX errors, " |
| 1988 |
"restarting the controller\n"); |
| 1989 |
b43_controller_restart(dev, "PHY TX errors"); |
| 1990 |
} |
| 1991 |
} |
| 1992 |
|
| 1993 |
if (unlikely(merged_dma_reason & (B43_DMAIRQ_FATALMASK))) { |
| 1994 |
b43err(dev->wl, |
| 1995 |
"Fatal DMA error: 0x%08X, 0x%08X, 0x%08X, 0x%08X, 0x%08X, 0x%08X\n", |
| 1996 |
dma_reason[0], dma_reason[1], |
| 1997 |
dma_reason[2], dma_reason[3], |
| 1998 |
dma_reason[4], dma_reason[5]); |
| 1999 |
b43err(dev->wl, "This device does not support DMA " |
| 2000 |
"on your system. It will now be switched to PIO.\n"); |
| 2001 |
/* Fall back to PIO transfers if we get fatal DMA errors! */ |
| 2002 |
dev->use_pio = true; |
| 2003 |
b43_controller_restart(dev, "DMA error"); |
| 2004 |
return; |
| 2005 |
} |
| 2006 |
|
| 2007 |
if (unlikely(reason & B43_IRQ_UCODE_DEBUG)) |
| 2008 |
handle_irq_ucode_debug(dev); |
| 2009 |
if (reason & B43_IRQ_TBTT_INDI) |
| 2010 |
handle_irq_tbtt_indication(dev); |
| 2011 |
if (reason & B43_IRQ_ATIM_END) |
| 2012 |
handle_irq_atim_end(dev); |
| 2013 |
if (reason & B43_IRQ_BEACON) |
| 2014 |
handle_irq_beacon(dev); |
| 2015 |
if (reason & B43_IRQ_PMQ) |
| 2016 |
handle_irq_pmq(dev); |
| 2017 |
if (reason & B43_IRQ_TXFIFO_FLUSH_OK) { |
| 2018 |
;/* TODO */ |
| 2019 |
} |
| 2020 |
if (reason & B43_IRQ_NOISESAMPLE_OK) |
| 2021 |
handle_irq_noise(dev); |
| 2022 |
|
| 2023 |
/* Check the DMA reason registers for received data. */ |
| 2024 |
if (dma_reason[0] & B43_DMAIRQ_RDESC_UFLOW) { |
| 2025 |
if (B43_DEBUG) |
| 2026 |
b43warn(dev->wl, "RX descriptor underrun\n"); |
| 2027 |
b43_dma_handle_rx_overflow(dev->dma.rx_ring); |
| 2028 |
} |
| 2029 |
if (dma_reason[0] & B43_DMAIRQ_RX_DONE) { |
| 2030 |
if (b43_using_pio_transfers(dev)) |
| 2031 |
b43_pio_rx(dev->pio.rx_queue); |
| 2032 |
else |
| 2033 |
b43_dma_rx(dev->dma.rx_ring); |
| 2034 |
} |
| 2035 |
B43_WARN_ON(dma_reason[1] & B43_DMAIRQ_RX_DONE); |
| 2036 |
B43_WARN_ON(dma_reason[2] & B43_DMAIRQ_RX_DONE); |
| 2037 |
B43_WARN_ON(dma_reason[3] & B43_DMAIRQ_RX_DONE); |
| 2038 |
B43_WARN_ON(dma_reason[4] & B43_DMAIRQ_RX_DONE); |
| 2039 |
B43_WARN_ON(dma_reason[5] & B43_DMAIRQ_RX_DONE); |
| 2040 |
|
| 2041 |
if (reason & B43_IRQ_TX_OK) |
| 2042 |
handle_irq_transmit_status(dev); |
| 2043 |
|
| 2044 |
/* Re-enable interrupts on the device by restoring the current interrupt mask. */ |
| 2045 |
b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); |
| 2046 |
|
| 2047 |
#if B43_DEBUG |
| 2048 |
if (b43_debug(dev, B43_DBG_VERBOSESTATS)) { |
| 2049 |
dev->irq_count++; |
| 2050 |
for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) { |
| 2051 |
if (reason & (1 << i)) |
| 2052 |
dev->irq_bit_count[i]++; |
| 2053 |
} |
| 2054 |
} |
| 2055 |
#endif |
| 2056 |
} |
| 2057 |
|
| 2058 |
/* Interrupt thread handler. Handles device interrupts in thread context. */ |
| 2059 |
static irqreturn_t b43_interrupt_thread_handler(int irq, void *dev_id) |
| 2060 |
{ |
| 2061 |
struct b43_wldev *dev = dev_id; |
| 2062 |
|
| 2063 |
mutex_lock(&dev->wl->mutex); |
| 2064 |
b43_do_interrupt_thread(dev); |
| 2065 |
mutex_unlock(&dev->wl->mutex); |
| 2066 |
|
| 2067 |
return IRQ_HANDLED; |
| 2068 |
} |
| 2069 |
|
| 2070 |
static irqreturn_t b43_do_interrupt(struct b43_wldev *dev) |
| 2071 |
{ |
| 2072 |
u32 reason; |
| 2073 |
|
| 2074 |
/* This code runs under wl->hardirq_lock, but _only_ on non-SDIO busses. |
| 2075 |
* On SDIO, this runs under wl->mutex. */ |
| 2076 |
|
| 2077 |
reason = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); |
| 2078 |
if (reason == 0xffffffff) /* shared IRQ */ |
| 2079 |
return IRQ_NONE; |
| 2080 |
reason &= dev->irq_mask; |
| 2081 |
if (!reason) |
| 2082 |
return IRQ_NONE; |
| 2083 |
|
| 2084 |
dev->dma_reason[0] = b43_read32(dev, B43_MMIO_DMA0_REASON) |
| 2085 |
& 0x0001FC00; |
| 2086 |
dev->dma_reason[1] = b43_read32(dev, B43_MMIO_DMA1_REASON) |
| 2087 |
& 0x0000DC00; |
| 2088 |
dev->dma_reason[2] = b43_read32(dev, B43_MMIO_DMA2_REASON) |
| 2089 |
& 0x0000DC00; |
| 2090 |
dev->dma_reason[3] = b43_read32(dev, B43_MMIO_DMA3_REASON) |
| 2091 |
& 0x0001DC00; |
| 2092 |
dev->dma_reason[4] = b43_read32(dev, B43_MMIO_DMA4_REASON) |
| 2093 |
& 0x0000DC00; |
| 2094 |
/* Unused ring |
| 2095 |
dev->dma_reason[5] = b43_read32(dev, B43_MMIO_DMA5_REASON) |
| 2096 |
& 0x0000DC00; |
| 2097 |
*/ |
| 2098 |
|
| 2099 |
/* ACK the interrupt. */ |
| 2100 |
b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, reason); |
| 2101 |
b43_write32(dev, B43_MMIO_DMA0_REASON, dev->dma_reason[0]); |
| 2102 |
b43_write32(dev, B43_MMIO_DMA1_REASON, dev->dma_reason[1]); |
| 2103 |
b43_write32(dev, B43_MMIO_DMA2_REASON, dev->dma_reason[2]); |
| 2104 |
b43_write32(dev, B43_MMIO_DMA3_REASON, dev->dma_reason[3]); |
| 2105 |
b43_write32(dev, B43_MMIO_DMA4_REASON, dev->dma_reason[4]); |
| 2106 |
/* Unused ring |
| 2107 |
b43_write32(dev, B43_MMIO_DMA5_REASON, dev->dma_reason[5]); |
| 2108 |
*/ |
| 2109 |
|
| 2110 |
/* Disable IRQs on the device. The IRQ thread handler will re-enable them. */ |
| 2111 |
b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); |
| 2112 |
/* Save the reason bitmasks for the IRQ thread handler. */ |
| 2113 |
dev->irq_reason = reason; |
| 2114 |
|
| 2115 |
return IRQ_WAKE_THREAD; |
| 2116 |
} |
| 2117 |
|
| 2118 |
/* Interrupt handler top-half. This runs with interrupts disabled. */ |
| 2119 |
static irqreturn_t b43_interrupt_handler(int irq, void *dev_id) |
| 2120 |
{ |
| 2121 |
struct b43_wldev *dev = dev_id; |
| 2122 |
irqreturn_t ret; |
| 2123 |
|
| 2124 |
if (unlikely(b43_status(dev) < B43_STAT_STARTED)) |
| 2125 |
return IRQ_NONE; |
| 2126 |
|
| 2127 |
spin_lock(&dev->wl->hardirq_lock); |
| 2128 |
ret = b43_do_interrupt(dev); |
| 2129 |
spin_unlock(&dev->wl->hardirq_lock); |
| 2130 |
|
| 2131 |
return ret; |
| 2132 |
} |
| 2133 |
|
| 2134 |
/* SDIO interrupt handler. This runs in process context. */ |
| 2135 |
static void b43_sdio_interrupt_handler(struct b43_wldev *dev) |
| 2136 |
{ |
| 2137 |
struct b43_wl *wl = dev->wl; |
| 2138 |
irqreturn_t ret; |
| 2139 |
|
| 2140 |
mutex_lock(&wl->mutex); |
| 2141 |
|
| 2142 |
ret = b43_do_interrupt(dev); |
| 2143 |
if (ret == IRQ_WAKE_THREAD) |
| 2144 |
b43_do_interrupt_thread(dev); |
| 2145 |
|
| 2146 |
mutex_unlock(&wl->mutex); |
| 2147 |
} |
| 2148 |
|
| 2149 |
void b43_do_release_fw(struct b43_firmware_file *fw) |
| 2150 |
{ |
| 2151 |
release_firmware(fw->data); |
| 2152 |
fw->data = NULL; |
| 2153 |
fw->filename = NULL; |
| 2154 |
} |
| 2155 |
|
| 2156 |
static void b43_release_firmware(struct b43_wldev *dev) |
| 2157 |
{ |
| 2158 |
complete(&dev->fw_load_complete); |
| 2159 |
b43_do_release_fw(&dev->fw.ucode); |
| 2160 |
b43_do_release_fw(&dev->fw.pcm); |
| 2161 |
b43_do_release_fw(&dev->fw.initvals); |
| 2162 |
b43_do_release_fw(&dev->fw.initvals_band); |
| 2163 |
} |
| 2164 |
|
| 2165 |
static void b43_print_fw_helptext(struct b43_wl *wl, bool error) |
| 2166 |
{ |
| 2167 |
const char text[] = |
| 2168 |
"You must go to " \ |
| 2169 |
"https://wireless.docs.kernel.org/en/latest/en/users/drivers/b43/developers.html#list-of-firmware " \ |
| 2170 |
"and download the correct firmware for this driver version. " \ |
| 2171 |
"Please carefully read all instructions on this website.\n"; |
| 2172 |
|
| 2173 |
if (error) |
| 2174 |
b43err(wl, text); |
| 2175 |
else |
| 2176 |
b43warn(wl, text); |
| 2177 |
} |
| 2178 |
|
| 2179 |
static void b43_fw_cb(const struct firmware *firmware, void *context) |
| 2180 |
{ |
| 2181 |
struct b43_request_fw_context *ctx = context; |
| 2182 |
|
| 2183 |
ctx->blob = firmware; |
| 2184 |
complete(&ctx->dev->fw_load_complete); |
| 2185 |
} |
| 2186 |
|
| 2187 |
int b43_do_request_fw(struct b43_request_fw_context *ctx, |
| 2188 |
const char *name, |
| 2189 |
struct b43_firmware_file *fw, bool async) |
| 2190 |
{ |
| 2191 |
struct b43_fw_header *hdr; |
| 2192 |
u32 size; |
| 2193 |
int err; |
| 2194 |
|
| 2195 |
if (!name) { |
| 2196 |
/* Don't fetch anything. Free possibly cached firmware. */ |
| 2197 |
/* FIXME: We should probably keep it anyway, to save some headache |
| 2198 |
* on suspend/resume with multiband devices. */ |
| 2199 |
b43_do_release_fw(fw); |
| 2200 |
return 0; |
| 2201 |
} |
| 2202 |
if (fw->filename) { |
| 2203 |
if ((fw->type == ctx->req_type) && |
| 2204 |
(strcmp(fw->filename, name) == 0)) |
| 2205 |
return 0; /* Already have this fw. */ |
| 2206 |
/* Free the cached firmware first. */ |
| 2207 |
/* FIXME: We should probably do this later after we successfully |
| 2208 |
* got the new fw. This could reduce headache with multiband devices. |
| 2209 |
* We could also redesign this to cache the firmware for all possible |
| 2210 |
* bands all the time. */ |
| 2211 |
b43_do_release_fw(fw); |
| 2212 |
} |
| 2213 |
|
| 2214 |
switch (ctx->req_type) { |
| 2215 |
case B43_FWTYPE_PROPRIETARY: |
| 2216 |
snprintf(ctx->fwname, sizeof(ctx->fwname), |
| 2217 |
"b43%s/%s.fw", |
| 2218 |
modparam_fwpostfix, name); |
| 2219 |
break; |
| 2220 |
case B43_FWTYPE_OPENSOURCE: |
| 2221 |
snprintf(ctx->fwname, sizeof(ctx->fwname), |
| 2222 |
"b43-open%s/%s.fw", |
| 2223 |
modparam_fwpostfix, name); |
| 2224 |
break; |
| 2225 |
default: |
| 2226 |
B43_WARN_ON(1); |
| 2227 |
return -ENOSYS; |
| 2228 |
} |
| 2229 |
if (async) { |
| 2230 |
/* do this part asynchronously */ |
| 2231 |
init_completion(&ctx->dev->fw_load_complete); |
| 2232 |
err = request_firmware_nowait(THIS_MODULE, 1, ctx->fwname, |
| 2233 |
ctx->dev->dev->dev, GFP_KERNEL, |
| 2234 |
ctx, b43_fw_cb); |
| 2235 |
if (err < 0) { |
| 2236 |
pr_err("Unable to load firmware\n"); |
| 2237 |
return err; |
| 2238 |
} |
| 2239 |
wait_for_completion(&ctx->dev->fw_load_complete); |
| 2240 |
if (ctx->blob) |
| 2241 |
goto fw_ready; |
| 2242 |
/* On some ARM systems, the async request will fail, but the next sync |
| 2243 |
* request works. For this reason, we fall through here |
| 2244 |
*/ |
| 2245 |
} |
| 2246 |
err = request_firmware(&ctx->blob, ctx->fwname, |
| 2247 |
ctx->dev->dev->dev); |
| 2248 |
if (err == -ENOENT) { |
| 2249 |
snprintf(ctx->errors[ctx->req_type], |
| 2250 |
sizeof(ctx->errors[ctx->req_type]), |
| 2251 |
"Firmware file \"%s\" not found\n", |
| 2252 |
ctx->fwname); |
| 2253 |
return err; |
| 2254 |
} else if (err) { |
| 2255 |
snprintf(ctx->errors[ctx->req_type], |
| 2256 |
sizeof(ctx->errors[ctx->req_type]), |
| 2257 |
"Firmware file \"%s\" request failed (err=%d)\n", |
| 2258 |
ctx->fwname, err); |
| 2259 |
return err; |
| 2260 |
} |
| 2261 |
fw_ready: |
| 2262 |
if (ctx->blob->size < sizeof(struct b43_fw_header)) |
| 2263 |
goto err_format; |
| 2264 |
hdr = (struct b43_fw_header *)(ctx->blob->data); |
| 2265 |
switch (hdr->type) { |
| 2266 |
case B43_FW_TYPE_UCODE: |
| 2267 |
case B43_FW_TYPE_PCM: |
| 2268 |
size = be32_to_cpu(hdr->size); |
| 2269 |
if (size != ctx->blob->size - sizeof(struct b43_fw_header)) |
| 2270 |
goto err_format; |
| 2271 |
fallthrough; |
| 2272 |
case B43_FW_TYPE_IV: |
| 2273 |
if (hdr->ver != 1) |
| 2274 |
goto err_format; |
| 2275 |
break; |
| 2276 |
default: |
| 2277 |
goto err_format; |
| 2278 |
} |
| 2279 |
|
| 2280 |
fw->data = ctx->blob; |
| 2281 |
fw->filename = name; |
| 2282 |
fw->type = ctx->req_type; |
| 2283 |
|
| 2284 |
return 0; |
| 2285 |
|
| 2286 |
err_format: |
| 2287 |
snprintf(ctx->errors[ctx->req_type], |
| 2288 |
sizeof(ctx->errors[ctx->req_type]), |
| 2289 |
"Firmware file \"%s\" format error.\n", ctx->fwname); |
| 2290 |
release_firmware(ctx->blob); |
| 2291 |
|
| 2292 |
return -EPROTO; |
| 2293 |
} |
| 2294 |
|
| 2295 |
/* https://bcm-v4.sipsolutions.net/802.11/Init/Firmware */ |
| 2296 |
static int b43_try_request_fw(struct b43_request_fw_context *ctx) |
| 2297 |
{ |
| 2298 |
struct b43_wldev *dev = ctx->dev; |
| 2299 |
struct b43_firmware *fw = &ctx->dev->fw; |
| 2300 |
struct b43_phy *phy = &dev->phy; |
| 2301 |
const u8 rev = ctx->dev->dev->core_rev; |
| 2302 |
const char *filename; |
| 2303 |
int err; |
| 2304 |
|
| 2305 |
/* Get microcode */ |
| 2306 |
filename = NULL; |
| 2307 |
switch (rev) { |
| 2308 |
case 42: |
| 2309 |
if (phy->type == B43_PHYTYPE_AC) |
| 2310 |
filename = "ucode42"; |
| 2311 |
break; |
| 2312 |
case 40: |
| 2313 |
if (phy->type == B43_PHYTYPE_AC) |
| 2314 |
filename = "ucode40"; |
| 2315 |
break; |
| 2316 |
case 33: |
| 2317 |
if (phy->type == B43_PHYTYPE_LCN40) |
| 2318 |
filename = "ucode33_lcn40"; |
| 2319 |
break; |
| 2320 |
case 30: |
| 2321 |
if (phy->type == B43_PHYTYPE_N) |
| 2322 |
filename = "ucode30_mimo"; |
| 2323 |
break; |
| 2324 |
case 29: |
| 2325 |
if (phy->type == B43_PHYTYPE_HT) |
| 2326 |
filename = "ucode29_mimo"; |
| 2327 |
break; |
| 2328 |
case 26: |
| 2329 |
if (phy->type == B43_PHYTYPE_HT) |
| 2330 |
filename = "ucode26_mimo"; |
| 2331 |
break; |
| 2332 |
case 28: |
| 2333 |
case 25: |
| 2334 |
if (phy->type == B43_PHYTYPE_N) |
| 2335 |
filename = "ucode25_mimo"; |
| 2336 |
else if (phy->type == B43_PHYTYPE_LCN) |
| 2337 |
filename = "ucode25_lcn"; |
| 2338 |
break; |
| 2339 |
case 24: |
| 2340 |
if (phy->type == B43_PHYTYPE_LCN) |
| 2341 |
filename = "ucode24_lcn"; |
| 2342 |
break; |
| 2343 |
case 23: |
| 2344 |
if (phy->type == B43_PHYTYPE_N) |
| 2345 |
filename = "ucode16_mimo"; |
| 2346 |
break; |
| 2347 |
case 16 ... 19: |
| 2348 |
if (phy->type == B43_PHYTYPE_N) |
| 2349 |
filename = "ucode16_mimo"; |
| 2350 |
else if (phy->type == B43_PHYTYPE_LP) |
| 2351 |
filename = "ucode16_lp"; |
| 2352 |
break; |
| 2353 |
case 15: |
| 2354 |
filename = "ucode15"; |
| 2355 |
break; |
| 2356 |
case 14: |
| 2357 |
filename = "ucode14"; |
| 2358 |
break; |
| 2359 |
case 13: |
| 2360 |
filename = "ucode13"; |
| 2361 |
break; |
| 2362 |
case 11 ... 12: |
| 2363 |
filename = "ucode11"; |
| 2364 |
break; |
| 2365 |
case 5 ... 10: |
| 2366 |
filename = "ucode5"; |
| 2367 |
break; |
| 2368 |
} |
| 2369 |
if (!filename) |
| 2370 |
goto err_no_ucode; |
| 2371 |
err = b43_do_request_fw(ctx, filename, &fw->ucode, true); |
| 2372 |
if (err) |
| 2373 |
goto err_load; |
| 2374 |
|
| 2375 |
/* Get PCM code */ |
| 2376 |
if ((rev >= 5) && (rev <= 10)) |
| 2377 |
filename = "pcm5"; |
| 2378 |
else if (rev >= 11) |
| 2379 |
filename = NULL; |
| 2380 |
else |
| 2381 |
goto err_no_pcm; |
| 2382 |
fw->pcm_request_failed = false; |
| 2383 |
err = b43_do_request_fw(ctx, filename, &fw->pcm, false); |
| 2384 |
if (err == -ENOENT) { |
| 2385 |
/* We did not find a PCM file? Not fatal, but |
| 2386 |
* core rev <= 10 must do without hwcrypto then. */ |
| 2387 |
fw->pcm_request_failed = true; |
| 2388 |
} else if (err) |
| 2389 |
goto err_load; |
| 2390 |
|
| 2391 |
/* Get initvals */ |
| 2392 |
filename = NULL; |
| 2393 |
switch (dev->phy.type) { |
| 2394 |
case B43_PHYTYPE_G: |
| 2395 |
if (rev == 13) |
| 2396 |
filename = "b0g0initvals13"; |
| 2397 |
else if (rev >= 5 && rev <= 10) |
| 2398 |
filename = "b0g0initvals5"; |
| 2399 |
break; |
| 2400 |
case B43_PHYTYPE_N: |
| 2401 |
if (rev == 30) |
| 2402 |
filename = "n16initvals30"; |
| 2403 |
else if (rev == 28 || rev == 25) |
| 2404 |
filename = "n0initvals25"; |
| 2405 |
else if (rev == 24) |
| 2406 |
filename = "n0initvals24"; |
| 2407 |
else if (rev == 23) |
| 2408 |
filename = "n0initvals16"; /* What about n0initvals22? */ |
| 2409 |
else if (rev >= 16 && rev <= 18) |
| 2410 |
filename = "n0initvals16"; |
| 2411 |
else if (rev >= 11 && rev <= 12) |
| 2412 |
filename = "n0initvals11"; |
| 2413 |
break; |
| 2414 |
case B43_PHYTYPE_LP: |
| 2415 |
if (rev >= 16 && rev <= 18) |
| 2416 |
filename = "lp0initvals16"; |
| 2417 |
else if (rev == 15) |
| 2418 |
filename = "lp0initvals15"; |
| 2419 |
else if (rev == 14) |
| 2420 |
filename = "lp0initvals14"; |
| 2421 |
else if (rev == 13) |
| 2422 |
filename = "lp0initvals13"; |
| 2423 |
break; |
| 2424 |
case B43_PHYTYPE_HT: |
| 2425 |
if (rev == 29) |
| 2426 |
filename = "ht0initvals29"; |
| 2427 |
else if (rev == 26) |
| 2428 |
filename = "ht0initvals26"; |
| 2429 |
break; |
| 2430 |
case B43_PHYTYPE_LCN: |
| 2431 |
if (rev == 24) |
| 2432 |
filename = "lcn0initvals24"; |
| 2433 |
break; |
| 2434 |
case B43_PHYTYPE_LCN40: |
| 2435 |
if (rev == 33) |
| 2436 |
filename = "lcn400initvals33"; |
| 2437 |
break; |
| 2438 |
case B43_PHYTYPE_AC: |
| 2439 |
if (rev == 42) |
| 2440 |
filename = "ac1initvals42"; |
| 2441 |
else if (rev == 40) |
| 2442 |
filename = "ac0initvals40"; |
| 2443 |
break; |
| 2444 |
} |
| 2445 |
if (!filename) |
| 2446 |
goto err_no_initvals; |
| 2447 |
err = b43_do_request_fw(ctx, filename, &fw->initvals, false); |
| 2448 |
if (err) |
| 2449 |
goto err_load; |
| 2450 |
|
| 2451 |
/* Get bandswitch initvals */ |
| 2452 |
filename = NULL; |
| 2453 |
switch (dev->phy.type) { |
| 2454 |
case B43_PHYTYPE_G: |
| 2455 |
if (rev == 13) |
| 2456 |
filename = "b0g0bsinitvals13"; |
| 2457 |
else if (rev >= 5 && rev <= 10) |
| 2458 |
filename = "b0g0bsinitvals5"; |
| 2459 |
break; |
| 2460 |
case B43_PHYTYPE_N: |
| 2461 |
if (rev == 30) |
| 2462 |
filename = "n16bsinitvals30"; |
| 2463 |
else if (rev == 28 || rev == 25) |
| 2464 |
filename = "n0bsinitvals25"; |
| 2465 |
else if (rev == 24) |
| 2466 |
filename = "n0bsinitvals24"; |
| 2467 |
else if (rev == 23) |
| 2468 |
filename = "n0bsinitvals16"; /* What about n0bsinitvals22? */ |
| 2469 |
else if (rev >= 16 && rev <= 18) |
| 2470 |
filename = "n0bsinitvals16"; |
| 2471 |
else if (rev >= 11 && rev <= 12) |
| 2472 |
filename = "n0bsinitvals11"; |
| 2473 |
break; |
| 2474 |
case B43_PHYTYPE_LP: |
| 2475 |
if (rev >= 16 && rev <= 18) |
| 2476 |
filename = "lp0bsinitvals16"; |
| 2477 |
else if (rev == 15) |
| 2478 |
filename = "lp0bsinitvals15"; |
| 2479 |
else if (rev == 14) |
| 2480 |
filename = "lp0bsinitvals14"; |
| 2481 |
else if (rev == 13) |
| 2482 |
filename = "lp0bsinitvals13"; |
| 2483 |
break; |
| 2484 |
case B43_PHYTYPE_HT: |
| 2485 |
if (rev == 29) |
| 2486 |
filename = "ht0bsinitvals29"; |
| 2487 |
else if (rev == 26) |
| 2488 |
filename = "ht0bsinitvals26"; |
| 2489 |
break; |
| 2490 |
case B43_PHYTYPE_LCN: |
| 2491 |
if (rev == 24) |
| 2492 |
filename = "lcn0bsinitvals24"; |
| 2493 |
break; |
| 2494 |
case B43_PHYTYPE_LCN40: |
| 2495 |
if (rev == 33) |
| 2496 |
filename = "lcn400bsinitvals33"; |
| 2497 |
break; |
| 2498 |
case B43_PHYTYPE_AC: |
| 2499 |
if (rev == 42) |
| 2500 |
filename = "ac1bsinitvals42"; |
| 2501 |
else if (rev == 40) |
| 2502 |
filename = "ac0bsinitvals40"; |
| 2503 |
break; |
| 2504 |
} |
| 2505 |
if (!filename) |
| 2506 |
goto err_no_initvals; |
| 2507 |
err = b43_do_request_fw(ctx, filename, &fw->initvals_band, false); |
| 2508 |
if (err) |
| 2509 |
goto err_load; |
| 2510 |
|
| 2511 |
fw->opensource = (ctx->req_type == B43_FWTYPE_OPENSOURCE); |
| 2512 |
|
| 2513 |
return 0; |
| 2514 |
|
| 2515 |
err_no_ucode: |
| 2516 |
err = ctx->fatal_failure = -EOPNOTSUPP; |
| 2517 |
b43err(dev->wl, "The driver does not know which firmware (ucode) " |
| 2518 |
"is required for your device (wl-core rev %u)\n", rev); |
| 2519 |
goto error; |
| 2520 |
|
| 2521 |
err_no_pcm: |
| 2522 |
err = ctx->fatal_failure = -EOPNOTSUPP; |
| 2523 |
b43err(dev->wl, "The driver does not know which firmware (PCM) " |
| 2524 |
"is required for your device (wl-core rev %u)\n", rev); |
| 2525 |
goto error; |
| 2526 |
|
| 2527 |
err_no_initvals: |
| 2528 |
err = ctx->fatal_failure = -EOPNOTSUPP; |
| 2529 |
b43err(dev->wl, "The driver does not know which firmware (initvals) " |
| 2530 |
"is required for your device (wl-core rev %u)\n", rev); |
| 2531 |
goto error; |
| 2532 |
|
| 2533 |
err_load: |
| 2534 |
/* We failed to load this firmware image. The error message |
| 2535 |
* already is in ctx->errors. Return and let our caller decide |
| 2536 |
* what to do. */ |
| 2537 |
goto error; |
| 2538 |
|
| 2539 |
error: |
| 2540 |
b43_release_firmware(dev); |
| 2541 |
return err; |
| 2542 |
} |
| 2543 |
|
| 2544 |
static int b43_one_core_attach(struct b43_bus_dev *dev, struct b43_wl *wl); |
| 2545 |
static void b43_one_core_detach(struct b43_bus_dev *dev); |
| 2546 |
static int b43_rng_init(struct b43_wl *wl); |
| 2547 |
|
| 2548 |
static void b43_request_firmware(struct work_struct *work) |
| 2549 |
{ |
| 2550 |
struct b43_wl *wl = container_of(work, |
| 2551 |
struct b43_wl, firmware_load); |
| 2552 |
struct b43_wldev *dev = wl->current_dev; |
| 2553 |
struct b43_request_fw_context *ctx; |
| 2554 |
unsigned int i; |
| 2555 |
int err; |
| 2556 |
const char *errmsg; |
| 2557 |
|
| 2558 |
ctx = kzalloc_obj(*ctx); |
| 2559 |
if (!ctx) |
| 2560 |
return; |
| 2561 |
ctx->dev = dev; |
| 2562 |
|
| 2563 |
ctx->req_type = B43_FWTYPE_PROPRIETARY; |
| 2564 |
err = b43_try_request_fw(ctx); |
| 2565 |
if (!err) |
| 2566 |
goto start_ieee80211; /* Successfully loaded it. */ |
| 2567 |
/* Was fw version known? */ |
| 2568 |
if (ctx->fatal_failure) |
| 2569 |
goto out; |
| 2570 |
|
| 2571 |
/* proprietary fw not found, try open source */ |
| 2572 |
ctx->req_type = B43_FWTYPE_OPENSOURCE; |
| 2573 |
err = b43_try_request_fw(ctx); |
| 2574 |
if (!err) |
| 2575 |
goto start_ieee80211; /* Successfully loaded it. */ |
| 2576 |
if(ctx->fatal_failure) |
| 2577 |
goto out; |
| 2578 |
|
| 2579 |
/* Could not find a usable firmware. Print the errors. */ |
| 2580 |
for (i = 0; i < B43_NR_FWTYPES; i++) { |
| 2581 |
errmsg = ctx->errors[i]; |
| 2582 |
if (strlen(errmsg)) |
| 2583 |
b43err(dev->wl, "%s", errmsg); |
| 2584 |
} |
| 2585 |
b43_print_fw_helptext(dev->wl, 1); |
| 2586 |
goto out; |
| 2587 |
|
| 2588 |
start_ieee80211: |
| 2589 |
wl->hw->queues = B43_QOS_QUEUE_NUM; |
| 2590 |
if (!modparam_qos || dev->fw.opensource || |
| 2591 |
dev->dev->chip_id == BCMA_CHIP_ID_BCM4331) |
| 2592 |
wl->hw->queues = 1; |
| 2593 |
|
| 2594 |
err = ieee80211_register_hw(wl->hw); |
| 2595 |
if (err) |
| 2596 |
goto out; |
| 2597 |
wl->hw_registered = true; |
| 2598 |
b43_leds_register(wl->current_dev); |
| 2599 |
|
| 2600 |
/* Register HW RNG driver */ |
| 2601 |
b43_rng_init(wl); |
| 2602 |
|
| 2603 |
out: |
| 2604 |
kfree(ctx); |
| 2605 |
} |
| 2606 |
|
| 2607 |
static int b43_upload_microcode(struct b43_wldev *dev) |
| 2608 |
{ |
| 2609 |
struct wiphy *wiphy = dev->wl->hw->wiphy; |
| 2610 |
const size_t hdr_len = sizeof(struct b43_fw_header); |
| 2611 |
const __be32 *data; |
| 2612 |
unsigned int i, len; |
| 2613 |
u16 fwrev, fwpatch, fwdate, fwtime; |
| 2614 |
u32 tmp, macctl; |
| 2615 |
int err = 0; |
| 2616 |
|
| 2617 |
/* Jump the microcode PSM to offset 0 */ |
| 2618 |
macctl = b43_read32(dev, B43_MMIO_MACCTL); |
| 2619 |
B43_WARN_ON(macctl & B43_MACCTL_PSM_RUN); |
| 2620 |
macctl |= B43_MACCTL_PSM_JMP0; |
| 2621 |
b43_write32(dev, B43_MMIO_MACCTL, macctl); |
| 2622 |
/* Zero out all microcode PSM registers and shared memory. */ |
| 2623 |
for (i = 0; i < 64; i++) |
| 2624 |
b43_shm_write16(dev, B43_SHM_SCRATCH, i, 0); |
| 2625 |
for (i = 0; i < 4096; i += 2) |
| 2626 |
b43_shm_write16(dev, B43_SHM_SHARED, i, 0); |
| 2627 |
|
| 2628 |
/* Upload Microcode. */ |
| 2629 |
data = (__be32 *) (dev->fw.ucode.data->data + hdr_len); |
| 2630 |
len = (dev->fw.ucode.data->size - hdr_len) / sizeof(__be32); |
| 2631 |
b43_shm_control_word(dev, B43_SHM_UCODE | B43_SHM_AUTOINC_W, 0x0000); |
| 2632 |
for (i = 0; i < len; i++) { |
| 2633 |
b43_write32(dev, B43_MMIO_SHM_DATA, be32_to_cpu(data[i])); |
| 2634 |
udelay(10); |
| 2635 |
} |
| 2636 |
|
| 2637 |
if (dev->fw.pcm.data) { |
| 2638 |
/* Upload PCM data. */ |
| 2639 |
data = (__be32 *) (dev->fw.pcm.data->data + hdr_len); |
| 2640 |
len = (dev->fw.pcm.data->size - hdr_len) / sizeof(__be32); |
| 2641 |
b43_shm_control_word(dev, B43_SHM_HW, 0x01EA); |
| 2642 |
b43_write32(dev, B43_MMIO_SHM_DATA, 0x00004000); |
| 2643 |
/* No need for autoinc bit in SHM_HW */ |
| 2644 |
b43_shm_control_word(dev, B43_SHM_HW, 0x01EB); |
| 2645 |
for (i = 0; i < len; i++) { |
| 2646 |
b43_write32(dev, B43_MMIO_SHM_DATA, be32_to_cpu(data[i])); |
| 2647 |
udelay(10); |
| 2648 |
} |
| 2649 |
} |
| 2650 |
|
| 2651 |
b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, B43_IRQ_ALL); |
| 2652 |
|
| 2653 |
/* Start the microcode PSM */ |
| 2654 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_JMP0, |
| 2655 |
B43_MACCTL_PSM_RUN); |
| 2656 |
|
| 2657 |
/* Wait for the microcode to load and respond */ |
| 2658 |
i = 0; |
| 2659 |
while (1) { |
| 2660 |
tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); |
| 2661 |
if (tmp == B43_IRQ_MAC_SUSPENDED) |
| 2662 |
break; |
| 2663 |
i++; |
| 2664 |
if (i >= 20) { |
| 2665 |
b43err(dev->wl, "Microcode not responding\n"); |
| 2666 |
b43_print_fw_helptext(dev->wl, 1); |
| 2667 |
err = -ENODEV; |
| 2668 |
goto error; |
| 2669 |
} |
| 2670 |
msleep(50); |
| 2671 |
} |
| 2672 |
b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); /* dummy read */ |
| 2673 |
|
| 2674 |
/* Get and check the revisions. */ |
| 2675 |
fwrev = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEREV); |
| 2676 |
fwpatch = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEPATCH); |
| 2677 |
fwdate = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODEDATE); |
| 2678 |
fwtime = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_UCODETIME); |
| 2679 |
|
| 2680 |
if (fwrev <= 0x128) { |
| 2681 |
b43err(dev->wl, "YOUR FIRMWARE IS TOO OLD. Firmware from " |
| 2682 |
"binary drivers older than version 4.x is unsupported. " |
| 2683 |
"You must upgrade your firmware files.\n"); |
| 2684 |
b43_print_fw_helptext(dev->wl, 1); |
| 2685 |
err = -EOPNOTSUPP; |
| 2686 |
goto error; |
| 2687 |
} |
| 2688 |
dev->fw.rev = fwrev; |
| 2689 |
dev->fw.patch = fwpatch; |
| 2690 |
if (dev->fw.rev >= 598) |
| 2691 |
dev->fw.hdr_format = B43_FW_HDR_598; |
| 2692 |
else if (dev->fw.rev >= 410) |
| 2693 |
dev->fw.hdr_format = B43_FW_HDR_410; |
| 2694 |
else |
| 2695 |
dev->fw.hdr_format = B43_FW_HDR_351; |
| 2696 |
WARN_ON(dev->fw.opensource != (fwdate == 0xFFFF)); |
| 2697 |
|
| 2698 |
dev->qos_enabled = dev->wl->hw->queues > 1; |
| 2699 |
/* Default to firmware/hardware crypto acceleration. */ |
| 2700 |
dev->hwcrypto_enabled = true; |
| 2701 |
|
| 2702 |
if (dev->fw.opensource) { |
| 2703 |
u16 fwcapa; |
| 2704 |
|
| 2705 |
/* Patchlevel info is encoded in the "time" field. */ |
| 2706 |
dev->fw.patch = fwtime; |
| 2707 |
b43info(dev->wl, "Loading OpenSource firmware version %u.%u\n", |
| 2708 |
dev->fw.rev, dev->fw.patch); |
| 2709 |
|
| 2710 |
fwcapa = b43_fwcapa_read(dev); |
| 2711 |
if (!(fwcapa & B43_FWCAPA_HWCRYPTO) || dev->fw.pcm_request_failed) { |
| 2712 |
b43info(dev->wl, "Hardware crypto acceleration not supported by firmware\n"); |
| 2713 |
/* Disable hardware crypto and fall back to software crypto. */ |
| 2714 |
dev->hwcrypto_enabled = false; |
| 2715 |
} |
| 2716 |
/* adding QoS support should use an offline discovery mechanism */ |
| 2717 |
WARN(fwcapa & B43_FWCAPA_QOS, "QoS in OpenFW not supported\n"); |
| 2718 |
} else { |
| 2719 |
b43info(dev->wl, "Loading firmware version %u.%u " |
| 2720 |
"(20%.2i-%.2i-%.2i %.2i:%.2i:%.2i)\n", |
| 2721 |
fwrev, fwpatch, |
| 2722 |
(fwdate >> 12) & 0xF, (fwdate >> 8) & 0xF, fwdate & 0xFF, |
| 2723 |
(fwtime >> 11) & 0x1F, (fwtime >> 5) & 0x3F, fwtime & 0x1F); |
| 2724 |
if (dev->fw.pcm_request_failed) { |
| 2725 |
b43warn(dev->wl, "No \"pcm5.fw\" firmware file found. " |
| 2726 |
"Hardware accelerated cryptography is disabled.\n"); |
| 2727 |
b43_print_fw_helptext(dev->wl, 0); |
| 2728 |
} |
| 2729 |
} |
| 2730 |
|
| 2731 |
snprintf(wiphy->fw_version, sizeof(wiphy->fw_version), "%u.%u", |
| 2732 |
dev->fw.rev, dev->fw.patch); |
| 2733 |
wiphy->hw_version = dev->dev->core_id; |
| 2734 |
|
| 2735 |
if (dev->fw.hdr_format == B43_FW_HDR_351) { |
| 2736 |
/* We're over the deadline, but we keep support for old fw |
| 2737 |
* until it turns out to be in major conflict with something new. */ |
| 2738 |
b43warn(dev->wl, "You are using an old firmware image. " |
| 2739 |
"Support for old firmware will be removed soon " |
| 2740 |
"(official deadline was July 2008).\n"); |
| 2741 |
b43_print_fw_helptext(dev->wl, 0); |
| 2742 |
} |
| 2743 |
|
| 2744 |
return 0; |
| 2745 |
|
| 2746 |
error: |
| 2747 |
/* Stop the microcode PSM. */ |
| 2748 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_RUN, |
| 2749 |
B43_MACCTL_PSM_JMP0); |
| 2750 |
|
| 2751 |
return err; |
| 2752 |
} |
| 2753 |
|
| 2754 |
static int b43_write_initvals(struct b43_wldev *dev, |
| 2755 |
const struct b43_iv *ivals, |
| 2756 |
size_t count, |
| 2757 |
size_t array_size) |
| 2758 |
{ |
| 2759 |
const struct b43_iv *iv; |
| 2760 |
u16 offset; |
| 2761 |
size_t i; |
| 2762 |
bool bit32; |
| 2763 |
|
| 2764 |
BUILD_BUG_ON(sizeof(struct b43_iv) != 6); |
| 2765 |
iv = ivals; |
| 2766 |
for (i = 0; i < count; i++) { |
| 2767 |
if (array_size < sizeof(iv->offset_size)) |
| 2768 |
goto err_format; |
| 2769 |
array_size -= sizeof(iv->offset_size); |
| 2770 |
offset = be16_to_cpu(iv->offset_size); |
| 2771 |
bit32 = !!(offset & B43_IV_32BIT); |
| 2772 |
offset &= B43_IV_OFFSET_MASK; |
| 2773 |
if (offset >= 0x1000) |
| 2774 |
goto err_format; |
| 2775 |
if (bit32) { |
| 2776 |
u32 value; |
| 2777 |
|
| 2778 |
if (array_size < sizeof(iv->data.d32)) |
| 2779 |
goto err_format; |
| 2780 |
array_size -= sizeof(iv->data.d32); |
| 2781 |
|
| 2782 |
value = get_unaligned_be32(&iv->data.d32); |
| 2783 |
b43_write32(dev, offset, value); |
| 2784 |
|
| 2785 |
iv = (const struct b43_iv *)((const uint8_t *)iv + |
| 2786 |
sizeof(__be16) + |
| 2787 |
sizeof(__be32)); |
| 2788 |
} else { |
| 2789 |
u16 value; |
| 2790 |
|
| 2791 |
if (array_size < sizeof(iv->data.d16)) |
| 2792 |
goto err_format; |
| 2793 |
array_size -= sizeof(iv->data.d16); |
| 2794 |
|
| 2795 |
value = be16_to_cpu(iv->data.d16); |
| 2796 |
b43_write16(dev, offset, value); |
| 2797 |
|
| 2798 |
iv = (const struct b43_iv *)((const uint8_t *)iv + |
| 2799 |
sizeof(__be16) + |
| 2800 |
sizeof(__be16)); |
| 2801 |
} |
| 2802 |
} |
| 2803 |
if (array_size) |
| 2804 |
goto err_format; |
| 2805 |
|
| 2806 |
return 0; |
| 2807 |
|
| 2808 |
err_format: |
| 2809 |
b43err(dev->wl, "Initial Values Firmware file-format error.\n"); |
| 2810 |
b43_print_fw_helptext(dev->wl, 1); |
| 2811 |
|
| 2812 |
return -EPROTO; |
| 2813 |
} |
| 2814 |
|
| 2815 |
static int b43_upload_initvals(struct b43_wldev *dev) |
| 2816 |
{ |
| 2817 |
const size_t hdr_len = sizeof(struct b43_fw_header); |
| 2818 |
const struct b43_fw_header *hdr; |
| 2819 |
struct b43_firmware *fw = &dev->fw; |
| 2820 |
const struct b43_iv *ivals; |
| 2821 |
size_t count; |
| 2822 |
|
| 2823 |
hdr = (const struct b43_fw_header *)(fw->initvals.data->data); |
| 2824 |
ivals = (const struct b43_iv *)(fw->initvals.data->data + hdr_len); |
| 2825 |
count = be32_to_cpu(hdr->size); |
| 2826 |
return b43_write_initvals(dev, ivals, count, |
| 2827 |
fw->initvals.data->size - hdr_len); |
| 2828 |
} |
| 2829 |
|
| 2830 |
static int b43_upload_initvals_band(struct b43_wldev *dev) |
| 2831 |
{ |
| 2832 |
const size_t hdr_len = sizeof(struct b43_fw_header); |
| 2833 |
const struct b43_fw_header *hdr; |
| 2834 |
struct b43_firmware *fw = &dev->fw; |
| 2835 |
const struct b43_iv *ivals; |
| 2836 |
size_t count; |
| 2837 |
|
| 2838 |
if (!fw->initvals_band.data) |
| 2839 |
return 0; |
| 2840 |
|
| 2841 |
hdr = (const struct b43_fw_header *)(fw->initvals_band.data->data); |
| 2842 |
ivals = (const struct b43_iv *)(fw->initvals_band.data->data + hdr_len); |
| 2843 |
count = be32_to_cpu(hdr->size); |
| 2844 |
return b43_write_initvals(dev, ivals, count, |
| 2845 |
fw->initvals_band.data->size - hdr_len); |
| 2846 |
} |
| 2847 |
|
| 2848 |
/* Initialize the GPIOs |
| 2849 |
* https://bcm-specs.sipsolutions.net/GPIO |
| 2850 |
*/ |
| 2851 |
|
| 2852 |
#ifdef CONFIG_B43_SSB |
| 2853 |
static struct ssb_device *b43_ssb_gpio_dev(struct b43_wldev *dev) |
| 2854 |
{ |
| 2855 |
struct ssb_bus *bus = dev->dev->sdev->bus; |
| 2856 |
|
| 2857 |
#ifdef CONFIG_SSB_DRIVER_PCICORE |
| 2858 |
return (bus->chipco.dev ? bus->chipco.dev : bus->pcicore.dev); |
| 2859 |
#else |
| 2860 |
return bus->chipco.dev; |
| 2861 |
#endif |
| 2862 |
} |
| 2863 |
#endif |
| 2864 |
|
| 2865 |
static int b43_gpio_init(struct b43_wldev *dev) |
| 2866 |
{ |
| 2867 |
#ifdef CONFIG_B43_SSB |
| 2868 |
struct ssb_device *gpiodev; |
| 2869 |
#endif |
| 2870 |
u32 mask, set; |
| 2871 |
|
| 2872 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_GPOUTSMSK, 0); |
| 2873 |
b43_maskset16(dev, B43_MMIO_GPIO_MASK, ~0, 0xF); |
| 2874 |
|
| 2875 |
mask = 0x0000001F; |
| 2876 |
set = 0x0000000F; |
| 2877 |
if (dev->dev->chip_id == 0x4301) { |
| 2878 |
mask |= 0x0060; |
| 2879 |
set |= 0x0060; |
| 2880 |
} else if (dev->dev->chip_id == 0x5354) { |
| 2881 |
/* Don't allow overtaking buttons GPIOs */ |
| 2882 |
set &= 0x2; /* 0x2 is LED GPIO on BCM5354 */ |
| 2883 |
} |
| 2884 |
|
| 2885 |
if (0 /* FIXME: conditional unknown */ ) { |
| 2886 |
b43_write16(dev, B43_MMIO_GPIO_MASK, |
| 2887 |
b43_read16(dev, B43_MMIO_GPIO_MASK) |
| 2888 |
| 0x0100); |
| 2889 |
/* BT Coexistance Input */ |
| 2890 |
mask |= 0x0080; |
| 2891 |
set |= 0x0080; |
| 2892 |
/* BT Coexistance Out */ |
| 2893 |
mask |= 0x0100; |
| 2894 |
set |= 0x0100; |
| 2895 |
} |
| 2896 |
if (dev->dev->bus_sprom->boardflags_lo & B43_BFL_PACTRL) { |
| 2897 |
/* PA is controlled by gpio 9, let ucode handle it */ |
| 2898 |
b43_write16(dev, B43_MMIO_GPIO_MASK, |
| 2899 |
b43_read16(dev, B43_MMIO_GPIO_MASK) |
| 2900 |
| 0x0200); |
| 2901 |
mask |= 0x0200; |
| 2902 |
set |= 0x0200; |
| 2903 |
} |
| 2904 |
|
| 2905 |
switch (dev->dev->bus_type) { |
| 2906 |
#ifdef CONFIG_B43_BCMA |
| 2907 |
case B43_BUS_BCMA: |
| 2908 |
bcma_chipco_gpio_control(&dev->dev->bdev->bus->drv_cc, mask, set); |
| 2909 |
break; |
| 2910 |
#endif |
| 2911 |
#ifdef CONFIG_B43_SSB |
| 2912 |
case B43_BUS_SSB: |
| 2913 |
gpiodev = b43_ssb_gpio_dev(dev); |
| 2914 |
if (gpiodev) |
| 2915 |
ssb_write32(gpiodev, B43_GPIO_CONTROL, |
| 2916 |
(ssb_read32(gpiodev, B43_GPIO_CONTROL) |
| 2917 |
& ~mask) | set); |
| 2918 |
break; |
| 2919 |
#endif |
| 2920 |
} |
| 2921 |
|
| 2922 |
return 0; |
| 2923 |
} |
| 2924 |
|
| 2925 |
/* Turn off all GPIO stuff. Call this on module unload, for example. */ |
| 2926 |
static void b43_gpio_cleanup(struct b43_wldev *dev) |
| 2927 |
{ |
| 2928 |
#ifdef CONFIG_B43_SSB |
| 2929 |
struct ssb_device *gpiodev; |
| 2930 |
#endif |
| 2931 |
|
| 2932 |
switch (dev->dev->bus_type) { |
| 2933 |
#ifdef CONFIG_B43_BCMA |
| 2934 |
case B43_BUS_BCMA: |
| 2935 |
bcma_chipco_gpio_control(&dev->dev->bdev->bus->drv_cc, ~0, 0); |
| 2936 |
break; |
| 2937 |
#endif |
| 2938 |
#ifdef CONFIG_B43_SSB |
| 2939 |
case B43_BUS_SSB: |
| 2940 |
gpiodev = b43_ssb_gpio_dev(dev); |
| 2941 |
if (gpiodev) |
| 2942 |
ssb_write32(gpiodev, B43_GPIO_CONTROL, 0); |
| 2943 |
break; |
| 2944 |
#endif |
| 2945 |
} |
| 2946 |
} |
| 2947 |
|
| 2948 |
/* http://bcm-specs.sipsolutions.net/EnableMac */ |
| 2949 |
void b43_mac_enable(struct b43_wldev *dev) |
| 2950 |
{ |
| 2951 |
if (b43_debug(dev, B43_DBG_FIRMWARE)) { |
| 2952 |
u16 fwstate; |
| 2953 |
|
| 2954 |
fwstate = b43_shm_read16(dev, B43_SHM_SHARED, |
| 2955 |
B43_SHM_SH_UCODESTAT); |
| 2956 |
if ((fwstate != B43_SHM_SH_UCODESTAT_SUSP) && |
| 2957 |
(fwstate != B43_SHM_SH_UCODESTAT_SLEEP)) { |
| 2958 |
b43err(dev->wl, "b43_mac_enable(): The firmware " |
| 2959 |
"should be suspended, but current state is %u\n", |
| 2960 |
fwstate); |
| 2961 |
} |
| 2962 |
} |
| 2963 |
|
| 2964 |
dev->mac_suspended--; |
| 2965 |
B43_WARN_ON(dev->mac_suspended < 0); |
| 2966 |
if (dev->mac_suspended == 0) { |
| 2967 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_ENABLED); |
| 2968 |
b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, |
| 2969 |
B43_IRQ_MAC_SUSPENDED); |
| 2970 |
/* Commit writes */ |
| 2971 |
b43_read32(dev, B43_MMIO_MACCTL); |
| 2972 |
b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); |
| 2973 |
b43_power_saving_ctl_bits(dev, 0); |
| 2974 |
} |
| 2975 |
} |
| 2976 |
|
| 2977 |
/* https://bcm-specs.sipsolutions.net/SuspendMAC */ |
| 2978 |
void b43_mac_suspend(struct b43_wldev *dev) |
| 2979 |
{ |
| 2980 |
int i; |
| 2981 |
u32 tmp; |
| 2982 |
|
| 2983 |
might_sleep(); |
| 2984 |
B43_WARN_ON(dev->mac_suspended < 0); |
| 2985 |
|
| 2986 |
if (dev->mac_suspended == 0) { |
| 2987 |
b43_power_saving_ctl_bits(dev, B43_PS_AWAKE); |
| 2988 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_ENABLED, 0); |
| 2989 |
/* force pci to flush the write */ |
| 2990 |
b43_read32(dev, B43_MMIO_MACCTL); |
| 2991 |
for (i = 35; i; i--) { |
| 2992 |
tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); |
| 2993 |
if (tmp & B43_IRQ_MAC_SUSPENDED) |
| 2994 |
goto out; |
| 2995 |
udelay(10); |
| 2996 |
} |
| 2997 |
/* Hm, it seems this will take some time. Use msleep(). */ |
| 2998 |
for (i = 40; i; i--) { |
| 2999 |
tmp = b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); |
| 3000 |
if (tmp & B43_IRQ_MAC_SUSPENDED) |
| 3001 |
goto out; |
| 3002 |
msleep(1); |
| 3003 |
} |
| 3004 |
b43err(dev->wl, "MAC suspend failed\n"); |
| 3005 |
} |
| 3006 |
out: |
| 3007 |
dev->mac_suspended++; |
| 3008 |
} |
| 3009 |
|
| 3010 |
/* https://bcm-v4.sipsolutions.net/802.11/PHY/N/MacPhyClkSet */ |
| 3011 |
void b43_mac_phy_clock_set(struct b43_wldev *dev, bool on) |
| 3012 |
{ |
| 3013 |
u32 tmp; |
| 3014 |
|
| 3015 |
switch (dev->dev->bus_type) { |
| 3016 |
#ifdef CONFIG_B43_BCMA |
| 3017 |
case B43_BUS_BCMA: |
| 3018 |
tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); |
| 3019 |
if (on) |
| 3020 |
tmp |= B43_BCMA_IOCTL_MACPHYCLKEN; |
| 3021 |
else |
| 3022 |
tmp &= ~B43_BCMA_IOCTL_MACPHYCLKEN; |
| 3023 |
bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); |
| 3024 |
break; |
| 3025 |
#endif |
| 3026 |
#ifdef CONFIG_B43_SSB |
| 3027 |
case B43_BUS_SSB: |
| 3028 |
tmp = ssb_read32(dev->dev->sdev, SSB_TMSLOW); |
| 3029 |
if (on) |
| 3030 |
tmp |= B43_TMSLOW_MACPHYCLKEN; |
| 3031 |
else |
| 3032 |
tmp &= ~B43_TMSLOW_MACPHYCLKEN; |
| 3033 |
ssb_write32(dev->dev->sdev, SSB_TMSLOW, tmp); |
| 3034 |
break; |
| 3035 |
#endif |
| 3036 |
} |
| 3037 |
} |
| 3038 |
|
| 3039 |
/* brcms_b_switch_macfreq */ |
| 3040 |
void b43_mac_switch_freq(struct b43_wldev *dev, u8 spurmode) |
| 3041 |
{ |
| 3042 |
u16 chip_id = dev->dev->chip_id; |
| 3043 |
|
| 3044 |
if (chip_id == BCMA_CHIP_ID_BCM4331) { |
| 3045 |
switch (spurmode) { |
| 3046 |
case 2: /* 168 Mhz: 2^26/168 = 0x61862 */ |
| 3047 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x1862); |
| 3048 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); |
| 3049 |
break; |
| 3050 |
case 1: /* 164 Mhz: 2^26/164 = 0x63e70 */ |
| 3051 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x3e70); |
| 3052 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); |
| 3053 |
break; |
| 3054 |
default: /* 160 Mhz: 2^26/160 = 0x66666 */ |
| 3055 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x6666); |
| 3056 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x6); |
| 3057 |
break; |
| 3058 |
} |
| 3059 |
} else if (chip_id == BCMA_CHIP_ID_BCM43131 || |
| 3060 |
chip_id == BCMA_CHIP_ID_BCM43217 || |
| 3061 |
chip_id == BCMA_CHIP_ID_BCM43222 || |
| 3062 |
chip_id == BCMA_CHIP_ID_BCM43224 || |
| 3063 |
chip_id == BCMA_CHIP_ID_BCM43225 || |
| 3064 |
chip_id == BCMA_CHIP_ID_BCM43227 || |
| 3065 |
chip_id == BCMA_CHIP_ID_BCM43228) { |
| 3066 |
switch (spurmode) { |
| 3067 |
case 2: /* 126 Mhz */ |
| 3068 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x2082); |
| 3069 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); |
| 3070 |
break; |
| 3071 |
case 1: /* 123 Mhz */ |
| 3072 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x5341); |
| 3073 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); |
| 3074 |
break; |
| 3075 |
default: /* 120 Mhz */ |
| 3076 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x8889); |
| 3077 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8); |
| 3078 |
break; |
| 3079 |
} |
| 3080 |
} else if (dev->phy.type == B43_PHYTYPE_LCN) { |
| 3081 |
switch (spurmode) { |
| 3082 |
case 1: /* 82 Mhz */ |
| 3083 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0x7CE0); |
| 3084 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0xC); |
| 3085 |
break; |
| 3086 |
default: /* 80 Mhz */ |
| 3087 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, 0xCCCD); |
| 3088 |
b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0xC); |
| 3089 |
break; |
| 3090 |
} |
| 3091 |
} |
| 3092 |
} |
| 3093 |
|
| 3094 |
static void b43_adjust_opmode(struct b43_wldev *dev) |
| 3095 |
{ |
| 3096 |
struct b43_wl *wl = dev->wl; |
| 3097 |
u32 ctl; |
| 3098 |
u16 cfp_pretbtt; |
| 3099 |
|
| 3100 |
ctl = b43_read32(dev, B43_MMIO_MACCTL); |
| 3101 |
/* Reset status to STA infrastructure mode. */ |
| 3102 |
ctl &= ~B43_MACCTL_AP; |
| 3103 |
ctl &= ~B43_MACCTL_KEEP_CTL; |
| 3104 |
ctl &= ~B43_MACCTL_KEEP_BADPLCP; |
| 3105 |
ctl &= ~B43_MACCTL_KEEP_BAD; |
| 3106 |
ctl &= ~B43_MACCTL_PROMISC; |
| 3107 |
ctl &= ~B43_MACCTL_BEACPROMISC; |
| 3108 |
ctl |= B43_MACCTL_INFRA; |
| 3109 |
|
| 3110 |
if (b43_is_mode(wl, NL80211_IFTYPE_AP) || |
| 3111 |
b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT)) |
| 3112 |
ctl |= B43_MACCTL_AP; |
| 3113 |
else if (b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) |
| 3114 |
ctl &= ~B43_MACCTL_INFRA; |
| 3115 |
|
| 3116 |
if (wl->filter_flags & FIF_CONTROL) |
| 3117 |
ctl |= B43_MACCTL_KEEP_CTL; |
| 3118 |
if (wl->filter_flags & FIF_FCSFAIL) |
| 3119 |
ctl |= B43_MACCTL_KEEP_BAD; |
| 3120 |
if (wl->filter_flags & FIF_PLCPFAIL) |
| 3121 |
ctl |= B43_MACCTL_KEEP_BADPLCP; |
| 3122 |
if (wl->filter_flags & FIF_BCN_PRBRESP_PROMISC) |
| 3123 |
ctl |= B43_MACCTL_BEACPROMISC; |
| 3124 |
|
| 3125 |
/* Workaround: On old hardware the HW-MAC-address-filter |
| 3126 |
* doesn't work properly, so always run promisc in filter |
| 3127 |
* it in software. */ |
| 3128 |
if (dev->dev->core_rev <= 4) |
| 3129 |
ctl |= B43_MACCTL_PROMISC; |
| 3130 |
|
| 3131 |
b43_write32(dev, B43_MMIO_MACCTL, ctl); |
| 3132 |
|
| 3133 |
cfp_pretbtt = 2; |
| 3134 |
if ((ctl & B43_MACCTL_INFRA) && !(ctl & B43_MACCTL_AP)) { |
| 3135 |
if (dev->dev->chip_id == 0x4306 && |
| 3136 |
dev->dev->chip_rev == 3) |
| 3137 |
cfp_pretbtt = 100; |
| 3138 |
else |
| 3139 |
cfp_pretbtt = 50; |
| 3140 |
} |
| 3141 |
b43_write16(dev, 0x612, cfp_pretbtt); |
| 3142 |
|
| 3143 |
/* FIXME: We don't currently implement the PMQ mechanism, |
| 3144 |
* so always disable it. If we want to implement PMQ, |
| 3145 |
* we need to enable it here (clear DISCPMQ) in AP mode. |
| 3146 |
*/ |
| 3147 |
if (0 /* ctl & B43_MACCTL_AP */) |
| 3148 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_DISCPMQ, 0); |
| 3149 |
else |
| 3150 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_DISCPMQ); |
| 3151 |
} |
| 3152 |
|
| 3153 |
static void b43_rate_memory_write(struct b43_wldev *dev, u16 rate, int is_ofdm) |
| 3154 |
{ |
| 3155 |
u16 offset; |
| 3156 |
|
| 3157 |
if (is_ofdm) { |
| 3158 |
offset = 0x480; |
| 3159 |
offset += (b43_plcp_get_ratecode_ofdm(rate) & 0x000F) * 2; |
| 3160 |
} else { |
| 3161 |
offset = 0x4C0; |
| 3162 |
offset += (b43_plcp_get_ratecode_cck(rate) & 0x000F) * 2; |
| 3163 |
} |
| 3164 |
b43_shm_write16(dev, B43_SHM_SHARED, offset + 0x20, |
| 3165 |
b43_shm_read16(dev, B43_SHM_SHARED, offset)); |
| 3166 |
} |
| 3167 |
|
| 3168 |
static void b43_rate_memory_init(struct b43_wldev *dev) |
| 3169 |
{ |
| 3170 |
switch (dev->phy.type) { |
| 3171 |
case B43_PHYTYPE_G: |
| 3172 |
case B43_PHYTYPE_N: |
| 3173 |
case B43_PHYTYPE_LP: |
| 3174 |
case B43_PHYTYPE_HT: |
| 3175 |
case B43_PHYTYPE_LCN: |
| 3176 |
b43_rate_memory_write(dev, B43_OFDM_RATE_6MB, 1); |
| 3177 |
b43_rate_memory_write(dev, B43_OFDM_RATE_9MB, 1); |
| 3178 |
b43_rate_memory_write(dev, B43_OFDM_RATE_12MB, 1); |
| 3179 |
b43_rate_memory_write(dev, B43_OFDM_RATE_18MB, 1); |
| 3180 |
b43_rate_memory_write(dev, B43_OFDM_RATE_24MB, 1); |
| 3181 |
b43_rate_memory_write(dev, B43_OFDM_RATE_36MB, 1); |
| 3182 |
b43_rate_memory_write(dev, B43_OFDM_RATE_48MB, 1); |
| 3183 |
b43_rate_memory_write(dev, B43_OFDM_RATE_54MB, 1); |
| 3184 |
fallthrough; |
| 3185 |
case B43_PHYTYPE_B: |
| 3186 |
b43_rate_memory_write(dev, B43_CCK_RATE_1MB, 0); |
| 3187 |
b43_rate_memory_write(dev, B43_CCK_RATE_2MB, 0); |
| 3188 |
b43_rate_memory_write(dev, B43_CCK_RATE_5MB, 0); |
| 3189 |
b43_rate_memory_write(dev, B43_CCK_RATE_11MB, 0); |
| 3190 |
break; |
| 3191 |
default: |
| 3192 |
B43_WARN_ON(1); |
| 3193 |
} |
| 3194 |
} |
| 3195 |
|
| 3196 |
/* Set the default values for the PHY TX Control Words. */ |
| 3197 |
static void b43_set_phytxctl_defaults(struct b43_wldev *dev) |
| 3198 |
{ |
| 3199 |
u16 ctl = 0; |
| 3200 |
|
| 3201 |
ctl |= B43_TXH_PHY_ENC_CCK; |
| 3202 |
ctl |= B43_TXH_PHY_ANT01AUTO; |
| 3203 |
ctl |= B43_TXH_PHY_TXPWR; |
| 3204 |
|
| 3205 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BEACPHYCTL, ctl); |
| 3206 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL, ctl); |
| 3207 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL, ctl); |
| 3208 |
} |
| 3209 |
|
| 3210 |
/* Set the TX-Antenna for management frames sent by firmware. */ |
| 3211 |
static void b43_mgmtframe_txantenna(struct b43_wldev *dev, int antenna) |
| 3212 |
{ |
| 3213 |
u16 ant; |
| 3214 |
u16 tmp; |
| 3215 |
|
| 3216 |
ant = b43_antenna_to_phyctl(antenna); |
| 3217 |
|
| 3218 |
/* For ACK/CTS */ |
| 3219 |
tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL); |
| 3220 |
tmp = (tmp & ~B43_TXH_PHY_ANT) | ant; |
| 3221 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_ACKCTSPHYCTL, tmp); |
| 3222 |
/* For Probe Resposes */ |
| 3223 |
tmp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL); |
| 3224 |
tmp = (tmp & ~B43_TXH_PHY_ANT) | ant; |
| 3225 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRPHYCTL, tmp); |
| 3226 |
} |
| 3227 |
|
| 3228 |
/* This is the opposite of b43_chip_init() */ |
| 3229 |
static void b43_chip_exit(struct b43_wldev *dev) |
| 3230 |
{ |
| 3231 |
b43_phy_exit(dev); |
| 3232 |
b43_gpio_cleanup(dev); |
| 3233 |
/* firmware is released later */ |
| 3234 |
} |
| 3235 |
|
| 3236 |
/* Initialize the chip |
| 3237 |
* https://bcm-specs.sipsolutions.net/ChipInit |
| 3238 |
*/ |
| 3239 |
static int b43_chip_init(struct b43_wldev *dev) |
| 3240 |
{ |
| 3241 |
struct b43_phy *phy = &dev->phy; |
| 3242 |
int err; |
| 3243 |
u32 macctl; |
| 3244 |
u16 value16; |
| 3245 |
|
| 3246 |
/* Initialize the MAC control */ |
| 3247 |
macctl = B43_MACCTL_IHR_ENABLED | B43_MACCTL_SHM_ENABLED; |
| 3248 |
if (dev->phy.gmode) |
| 3249 |
macctl |= B43_MACCTL_GMODE; |
| 3250 |
macctl |= B43_MACCTL_INFRA; |
| 3251 |
b43_write32(dev, B43_MMIO_MACCTL, macctl); |
| 3252 |
|
| 3253 |
err = b43_upload_microcode(dev); |
| 3254 |
if (err) |
| 3255 |
goto out; /* firmware is released later */ |
| 3256 |
|
| 3257 |
err = b43_gpio_init(dev); |
| 3258 |
if (err) |
| 3259 |
goto out; /* firmware is released later */ |
| 3260 |
|
| 3261 |
err = b43_upload_initvals(dev); |
| 3262 |
if (err) |
| 3263 |
goto err_gpio_clean; |
| 3264 |
|
| 3265 |
err = b43_upload_initvals_band(dev); |
| 3266 |
if (err) |
| 3267 |
goto err_gpio_clean; |
| 3268 |
|
| 3269 |
/* Turn the Analog on and initialize the PHY. */ |
| 3270 |
phy->ops->switch_analog(dev, 1); |
| 3271 |
err = b43_phy_init(dev); |
| 3272 |
if (err) |
| 3273 |
goto err_gpio_clean; |
| 3274 |
|
| 3275 |
/* Disable Interference Mitigation. */ |
| 3276 |
if (phy->ops->interf_mitigation) |
| 3277 |
phy->ops->interf_mitigation(dev, B43_INTERFMODE_NONE); |
| 3278 |
|
| 3279 |
/* Select the antennae */ |
| 3280 |
if (phy->ops->set_rx_antenna) |
| 3281 |
phy->ops->set_rx_antenna(dev, B43_ANTENNA_DEFAULT); |
| 3282 |
b43_mgmtframe_txantenna(dev, B43_ANTENNA_DEFAULT); |
| 3283 |
|
| 3284 |
if (phy->type == B43_PHYTYPE_B) { |
| 3285 |
value16 = b43_read16(dev, 0x005E); |
| 3286 |
value16 |= 0x0004; |
| 3287 |
b43_write16(dev, 0x005E, value16); |
| 3288 |
} |
| 3289 |
b43_write32(dev, 0x0100, 0x01000000); |
| 3290 |
if (dev->dev->core_rev < 5) |
| 3291 |
b43_write32(dev, 0x010C, 0x01000000); |
| 3292 |
|
| 3293 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_INFRA, 0); |
| 3294 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_INFRA); |
| 3295 |
|
| 3296 |
/* Probe Response Timeout value */ |
| 3297 |
/* FIXME: Default to 0, has to be set by ioctl probably... :-/ */ |
| 3298 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRMAXTIME, 0); |
| 3299 |
|
| 3300 |
/* Initially set the wireless operation mode. */ |
| 3301 |
b43_adjust_opmode(dev); |
| 3302 |
|
| 3303 |
if (dev->dev->core_rev < 3) { |
| 3304 |
b43_write16(dev, 0x060E, 0x0000); |
| 3305 |
b43_write16(dev, 0x0610, 0x8000); |
| 3306 |
b43_write16(dev, 0x0604, 0x0000); |
| 3307 |
b43_write16(dev, 0x0606, 0x0200); |
| 3308 |
} else { |
| 3309 |
b43_write32(dev, 0x0188, 0x80000000); |
| 3310 |
b43_write32(dev, 0x018C, 0x02000000); |
| 3311 |
} |
| 3312 |
b43_write32(dev, B43_MMIO_GEN_IRQ_REASON, 0x00004000); |
| 3313 |
b43_write32(dev, B43_MMIO_DMA0_IRQ_MASK, 0x0001FC00); |
| 3314 |
b43_write32(dev, B43_MMIO_DMA1_IRQ_MASK, 0x0000DC00); |
| 3315 |
b43_write32(dev, B43_MMIO_DMA2_IRQ_MASK, 0x0000DC00); |
| 3316 |
b43_write32(dev, B43_MMIO_DMA3_IRQ_MASK, 0x0001DC00); |
| 3317 |
b43_write32(dev, B43_MMIO_DMA4_IRQ_MASK, 0x0000DC00); |
| 3318 |
b43_write32(dev, B43_MMIO_DMA5_IRQ_MASK, 0x0000DC00); |
| 3319 |
|
| 3320 |
b43_mac_phy_clock_set(dev, true); |
| 3321 |
|
| 3322 |
switch (dev->dev->bus_type) { |
| 3323 |
#ifdef CONFIG_B43_BCMA |
| 3324 |
case B43_BUS_BCMA: |
| 3325 |
/* FIXME: 0xE74 is quite common, but should be read from CC */ |
| 3326 |
b43_write16(dev, B43_MMIO_POWERUP_DELAY, 0xE74); |
| 3327 |
break; |
| 3328 |
#endif |
| 3329 |
#ifdef CONFIG_B43_SSB |
| 3330 |
case B43_BUS_SSB: |
| 3331 |
b43_write16(dev, B43_MMIO_POWERUP_DELAY, |
| 3332 |
dev->dev->sdev->bus->chipco.fast_pwrup_delay); |
| 3333 |
break; |
| 3334 |
#endif |
| 3335 |
} |
| 3336 |
|
| 3337 |
err = 0; |
| 3338 |
b43dbg(dev->wl, "Chip initialized\n"); |
| 3339 |
out: |
| 3340 |
return err; |
| 3341 |
|
| 3342 |
err_gpio_clean: |
| 3343 |
b43_gpio_cleanup(dev); |
| 3344 |
return err; |
| 3345 |
} |
| 3346 |
|
| 3347 |
static void b43_periodic_every60sec(struct b43_wldev *dev) |
| 3348 |
{ |
| 3349 |
const struct b43_phy_operations *ops = dev->phy.ops; |
| 3350 |
|
| 3351 |
if (ops->pwork_60sec) |
| 3352 |
ops->pwork_60sec(dev); |
| 3353 |
|
| 3354 |
/* Force check the TX power emission now. */ |
| 3355 |
b43_phy_txpower_check(dev, B43_TXPWR_IGNORE_TIME); |
| 3356 |
} |
| 3357 |
|
| 3358 |
static void b43_periodic_every30sec(struct b43_wldev *dev) |
| 3359 |
{ |
| 3360 |
/* Update device statistics. */ |
| 3361 |
b43_calculate_link_quality(dev); |
| 3362 |
} |
| 3363 |
|
| 3364 |
static void b43_periodic_every15sec(struct b43_wldev *dev) |
| 3365 |
{ |
| 3366 |
struct b43_phy *phy = &dev->phy; |
| 3367 |
u16 wdr; |
| 3368 |
|
| 3369 |
if (dev->fw.opensource) { |
| 3370 |
/* Check if the firmware is still alive. |
| 3371 |
* It will reset the watchdog counter to 0 in its idle loop. */ |
| 3372 |
wdr = b43_shm_read16(dev, B43_SHM_SCRATCH, B43_WATCHDOG_REG); |
| 3373 |
if (unlikely(wdr)) { |
| 3374 |
b43err(dev->wl, "Firmware watchdog: The firmware died!\n"); |
| 3375 |
b43_controller_restart(dev, "Firmware watchdog"); |
| 3376 |
return; |
| 3377 |
} else { |
| 3378 |
b43_shm_write16(dev, B43_SHM_SCRATCH, |
| 3379 |
B43_WATCHDOG_REG, 1); |
| 3380 |
} |
| 3381 |
} |
| 3382 |
|
| 3383 |
if (phy->ops->pwork_15sec) |
| 3384 |
phy->ops->pwork_15sec(dev); |
| 3385 |
|
| 3386 |
atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT); |
| 3387 |
wmb(); |
| 3388 |
|
| 3389 |
#if B43_DEBUG |
| 3390 |
if (b43_debug(dev, B43_DBG_VERBOSESTATS)) { |
| 3391 |
unsigned int i; |
| 3392 |
|
| 3393 |
b43dbg(dev->wl, "Stats: %7u IRQs/sec, %7u TX/sec, %7u RX/sec\n", |
| 3394 |
dev->irq_count / 15, |
| 3395 |
dev->tx_count / 15, |
| 3396 |
dev->rx_count / 15); |
| 3397 |
dev->irq_count = 0; |
| 3398 |
dev->tx_count = 0; |
| 3399 |
dev->rx_count = 0; |
| 3400 |
for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) { |
| 3401 |
if (dev->irq_bit_count[i]) { |
| 3402 |
b43dbg(dev->wl, "Stats: %7u IRQ-%02u/sec (0x%08X)\n", |
| 3403 |
dev->irq_bit_count[i] / 15, i, (1 << i)); |
| 3404 |
dev->irq_bit_count[i] = 0; |
| 3405 |
} |
| 3406 |
} |
| 3407 |
} |
| 3408 |
#endif |
| 3409 |
} |
| 3410 |
|
| 3411 |
static void do_periodic_work(struct b43_wldev *dev) |
| 3412 |
{ |
| 3413 |
unsigned int state; |
| 3414 |
|
| 3415 |
state = dev->periodic_state; |
| 3416 |
if (state % 4 == 0) |
| 3417 |
b43_periodic_every60sec(dev); |
| 3418 |
if (state % 2 == 0) |
| 3419 |
b43_periodic_every30sec(dev); |
| 3420 |
b43_periodic_every15sec(dev); |
| 3421 |
} |
| 3422 |
|
| 3423 |
/* Periodic work locking policy: |
| 3424 |
* The whole periodic work handler is protected by |
| 3425 |
* wl->mutex. If another lock is needed somewhere in the |
| 3426 |
* pwork callchain, it's acquired in-place, where it's needed. |
| 3427 |
*/ |
| 3428 |
static void b43_periodic_work_handler(struct work_struct *work) |
| 3429 |
{ |
| 3430 |
struct b43_wldev *dev = container_of(work, struct b43_wldev, |
| 3431 |
periodic_work.work); |
| 3432 |
struct b43_wl *wl = dev->wl; |
| 3433 |
unsigned long delay; |
| 3434 |
|
| 3435 |
mutex_lock(&wl->mutex); |
| 3436 |
|
| 3437 |
if (unlikely(b43_status(dev) != B43_STAT_STARTED)) |
| 3438 |
goto out; |
| 3439 |
if (b43_debug(dev, B43_DBG_PWORK_STOP)) |
| 3440 |
goto out_requeue; |
| 3441 |
|
| 3442 |
do_periodic_work(dev); |
| 3443 |
|
| 3444 |
dev->periodic_state++; |
| 3445 |
out_requeue: |
| 3446 |
if (b43_debug(dev, B43_DBG_PWORK_FAST)) |
| 3447 |
delay = msecs_to_jiffies(50); |
| 3448 |
else |
| 3449 |
delay = round_jiffies_relative(HZ * 15); |
| 3450 |
ieee80211_queue_delayed_work(wl->hw, &dev->periodic_work, delay); |
| 3451 |
out: |
| 3452 |
mutex_unlock(&wl->mutex); |
| 3453 |
} |
| 3454 |
|
| 3455 |
static void b43_periodic_tasks_setup(struct b43_wldev *dev) |
| 3456 |
{ |
| 3457 |
struct delayed_work *work = &dev->periodic_work; |
| 3458 |
|
| 3459 |
dev->periodic_state = 0; |
| 3460 |
INIT_DELAYED_WORK(work, b43_periodic_work_handler); |
| 3461 |
ieee80211_queue_delayed_work(dev->wl->hw, work, 0); |
| 3462 |
} |
| 3463 |
|
| 3464 |
/* Check if communication with the device works correctly. */ |
| 3465 |
static int b43_validate_chipaccess(struct b43_wldev *dev) |
| 3466 |
{ |
| 3467 |
u32 v, backup0, backup4; |
| 3468 |
|
| 3469 |
backup0 = b43_shm_read32(dev, B43_SHM_SHARED, 0); |
| 3470 |
backup4 = b43_shm_read32(dev, B43_SHM_SHARED, 4); |
| 3471 |
|
| 3472 |
/* Check for read/write and endianness problems. */ |
| 3473 |
b43_shm_write32(dev, B43_SHM_SHARED, 0, 0x55AAAA55); |
| 3474 |
if (b43_shm_read32(dev, B43_SHM_SHARED, 0) != 0x55AAAA55) |
| 3475 |
goto error; |
| 3476 |
b43_shm_write32(dev, B43_SHM_SHARED, 0, 0xAA5555AA); |
| 3477 |
if (b43_shm_read32(dev, B43_SHM_SHARED, 0) != 0xAA5555AA) |
| 3478 |
goto error; |
| 3479 |
|
| 3480 |
/* Check if unaligned 32bit SHM_SHARED access works properly. |
| 3481 |
* However, don't bail out on failure, because it's noncritical. */ |
| 3482 |
b43_shm_write16(dev, B43_SHM_SHARED, 0, 0x1122); |
| 3483 |
b43_shm_write16(dev, B43_SHM_SHARED, 2, 0x3344); |
| 3484 |
b43_shm_write16(dev, B43_SHM_SHARED, 4, 0x5566); |
| 3485 |
b43_shm_write16(dev, B43_SHM_SHARED, 6, 0x7788); |
| 3486 |
if (b43_shm_read32(dev, B43_SHM_SHARED, 2) != 0x55663344) |
| 3487 |
b43warn(dev->wl, "Unaligned 32bit SHM read access is broken\n"); |
| 3488 |
b43_shm_write32(dev, B43_SHM_SHARED, 2, 0xAABBCCDD); |
| 3489 |
if (b43_shm_read16(dev, B43_SHM_SHARED, 0) != 0x1122 || |
| 3490 |
b43_shm_read16(dev, B43_SHM_SHARED, 2) != 0xCCDD || |
| 3491 |
b43_shm_read16(dev, B43_SHM_SHARED, 4) != 0xAABB || |
| 3492 |
b43_shm_read16(dev, B43_SHM_SHARED, 6) != 0x7788) |
| 3493 |
b43warn(dev->wl, "Unaligned 32bit SHM write access is broken\n"); |
| 3494 |
|
| 3495 |
b43_shm_write32(dev, B43_SHM_SHARED, 0, backup0); |
| 3496 |
b43_shm_write32(dev, B43_SHM_SHARED, 4, backup4); |
| 3497 |
|
| 3498 |
if ((dev->dev->core_rev >= 3) && (dev->dev->core_rev <= 10)) { |
| 3499 |
/* The 32bit register shadows the two 16bit registers |
| 3500 |
* with update sideeffects. Validate this. */ |
| 3501 |
b43_write16(dev, B43_MMIO_TSF_CFP_START, 0xAAAA); |
| 3502 |
b43_write32(dev, B43_MMIO_TSF_CFP_START, 0xCCCCBBBB); |
| 3503 |
if (b43_read16(dev, B43_MMIO_TSF_CFP_START_LOW) != 0xBBBB) |
| 3504 |
goto error; |
| 3505 |
if (b43_read16(dev, B43_MMIO_TSF_CFP_START_HIGH) != 0xCCCC) |
| 3506 |
goto error; |
| 3507 |
} |
| 3508 |
b43_write32(dev, B43_MMIO_TSF_CFP_START, 0); |
| 3509 |
|
| 3510 |
v = b43_read32(dev, B43_MMIO_MACCTL); |
| 3511 |
v |= B43_MACCTL_GMODE; |
| 3512 |
if (v != (B43_MACCTL_GMODE | B43_MACCTL_IHR_ENABLED)) |
| 3513 |
goto error; |
| 3514 |
|
| 3515 |
return 0; |
| 3516 |
error: |
| 3517 |
b43err(dev->wl, "Failed to validate the chipaccess\n"); |
| 3518 |
return -ENODEV; |
| 3519 |
} |
| 3520 |
|
| 3521 |
static void b43_security_init(struct b43_wldev *dev) |
| 3522 |
{ |
| 3523 |
dev->ktp = b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_KTP); |
| 3524 |
/* KTP is a word address, but we address SHM bytewise. |
| 3525 |
* So multiply by two. |
| 3526 |
*/ |
| 3527 |
dev->ktp *= 2; |
| 3528 |
/* Number of RCMTA address slots */ |
| 3529 |
b43_write16(dev, B43_MMIO_RCMTA_COUNT, B43_NR_PAIRWISE_KEYS); |
| 3530 |
/* Clear the key memory. */ |
| 3531 |
b43_clear_keys(dev); |
| 3532 |
} |
| 3533 |
|
| 3534 |
#ifdef CONFIG_B43_HWRNG |
| 3535 |
static int b43_rng_read(struct hwrng *rng, u32 *data) |
| 3536 |
{ |
| 3537 |
struct b43_wl *wl = (struct b43_wl *)rng->priv; |
| 3538 |
struct b43_wldev *dev; |
| 3539 |
int count = -ENODEV; |
| 3540 |
|
| 3541 |
mutex_lock(&wl->mutex); |
| 3542 |
dev = wl->current_dev; |
| 3543 |
if (likely(dev && b43_status(dev) >= B43_STAT_INITIALIZED)) { |
| 3544 |
*data = b43_read16(dev, B43_MMIO_RNG); |
| 3545 |
count = sizeof(u16); |
| 3546 |
} |
| 3547 |
mutex_unlock(&wl->mutex); |
| 3548 |
|
| 3549 |
return count; |
| 3550 |
} |
| 3551 |
#endif /* CONFIG_B43_HWRNG */ |
| 3552 |
|
| 3553 |
static void b43_rng_exit(struct b43_wl *wl) |
| 3554 |
{ |
| 3555 |
#ifdef CONFIG_B43_HWRNG |
| 3556 |
if (wl->rng_initialized) |
| 3557 |
hwrng_unregister(&wl->rng); |
| 3558 |
#endif /* CONFIG_B43_HWRNG */ |
| 3559 |
} |
| 3560 |
|
| 3561 |
static int b43_rng_init(struct b43_wl *wl) |
| 3562 |
{ |
| 3563 |
int err = 0; |
| 3564 |
|
| 3565 |
#ifdef CONFIG_B43_HWRNG |
| 3566 |
snprintf(wl->rng_name, ARRAY_SIZE(wl->rng_name), |
| 3567 |
"%s_%s", KBUILD_MODNAME, wiphy_name(wl->hw->wiphy)); |
| 3568 |
wl->rng.name = wl->rng_name; |
| 3569 |
wl->rng.data_read = b43_rng_read; |
| 3570 |
wl->rng.priv = (unsigned long)wl; |
| 3571 |
wl->rng_initialized = true; |
| 3572 |
err = hwrng_register(&wl->rng); |
| 3573 |
if (err) { |
| 3574 |
wl->rng_initialized = false; |
| 3575 |
b43err(wl, "Failed to register the random " |
| 3576 |
"number generator (%d)\n", err); |
| 3577 |
} |
| 3578 |
#endif /* CONFIG_B43_HWRNG */ |
| 3579 |
|
| 3580 |
return err; |
| 3581 |
} |
| 3582 |
|
| 3583 |
static void b43_tx_work(struct work_struct *work) |
| 3584 |
{ |
| 3585 |
struct b43_wl *wl = container_of(work, struct b43_wl, tx_work); |
| 3586 |
struct b43_wldev *dev; |
| 3587 |
struct sk_buff *skb; |
| 3588 |
int queue_num; |
| 3589 |
int err = 0; |
| 3590 |
|
| 3591 |
mutex_lock(&wl->mutex); |
| 3592 |
dev = wl->current_dev; |
| 3593 |
if (unlikely(!dev || b43_status(dev) < B43_STAT_STARTED)) { |
| 3594 |
mutex_unlock(&wl->mutex); |
| 3595 |
return; |
| 3596 |
} |
| 3597 |
|
| 3598 |
for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { |
| 3599 |
while (skb_queue_len(&wl->tx_queue[queue_num])) { |
| 3600 |
skb = skb_dequeue(&wl->tx_queue[queue_num]); |
| 3601 |
if (b43_using_pio_transfers(dev)) |
| 3602 |
err = b43_pio_tx(dev, skb); |
| 3603 |
else |
| 3604 |
err = b43_dma_tx(dev, skb); |
| 3605 |
if (err == -ENOSPC) { |
| 3606 |
wl->tx_queue_stopped[queue_num] = true; |
| 3607 |
b43_stop_queue(dev, queue_num); |
| 3608 |
skb_queue_head(&wl->tx_queue[queue_num], skb); |
| 3609 |
break; |
| 3610 |
} |
| 3611 |
if (unlikely(err)) |
| 3612 |
ieee80211_free_txskb(wl->hw, skb); |
| 3613 |
err = 0; |
| 3614 |
} |
| 3615 |
|
| 3616 |
if (!err) |
| 3617 |
wl->tx_queue_stopped[queue_num] = false; |
| 3618 |
} |
| 3619 |
|
| 3620 |
#if B43_DEBUG |
| 3621 |
dev->tx_count++; |
| 3622 |
#endif |
| 3623 |
mutex_unlock(&wl->mutex); |
| 3624 |
} |
| 3625 |
|
| 3626 |
static void b43_op_tx(struct ieee80211_hw *hw, |
| 3627 |
struct ieee80211_tx_control *control, |
| 3628 |
struct sk_buff *skb) |
| 3629 |
{ |
| 3630 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 3631 |
u16 skb_queue_mapping; |
| 3632 |
|
| 3633 |
if (unlikely(skb->len < 2 + 2 + 6)) { |
| 3634 |
/* Too short, this can't be a valid frame. */ |
| 3635 |
ieee80211_free_txskb(hw, skb); |
| 3636 |
return; |
| 3637 |
} |
| 3638 |
B43_WARN_ON(skb_shinfo(skb)->nr_frags); |
| 3639 |
|
| 3640 |
skb_queue_mapping = skb_get_queue_mapping(skb); |
| 3641 |
skb_queue_tail(&wl->tx_queue[skb_queue_mapping], skb); |
| 3642 |
if (!wl->tx_queue_stopped[skb_queue_mapping]) |
| 3643 |
ieee80211_queue_work(wl->hw, &wl->tx_work); |
| 3644 |
else |
| 3645 |
b43_stop_queue(wl->current_dev, skb_queue_mapping); |
| 3646 |
} |
| 3647 |
|
| 3648 |
static void b43_qos_params_upload(struct b43_wldev *dev, |
| 3649 |
const struct ieee80211_tx_queue_params *p, |
| 3650 |
u16 shm_offset) |
| 3651 |
{ |
| 3652 |
u16 params[B43_NR_QOSPARAMS]; |
| 3653 |
int bslots, tmp; |
| 3654 |
unsigned int i; |
| 3655 |
|
| 3656 |
if (!dev->qos_enabled) |
| 3657 |
return; |
| 3658 |
|
| 3659 |
bslots = b43_read16(dev, B43_MMIO_RNG) & p->cw_min; |
| 3660 |
|
| 3661 |
memset(¶ms, 0, sizeof(params)); |
| 3662 |
|
| 3663 |
params[B43_QOSPARAM_TXOP] = p->txop * 32; |
| 3664 |
params[B43_QOSPARAM_CWMIN] = p->cw_min; |
| 3665 |
params[B43_QOSPARAM_CWMAX] = p->cw_max; |
| 3666 |
params[B43_QOSPARAM_CWCUR] = p->cw_min; |
| 3667 |
params[B43_QOSPARAM_AIFS] = p->aifs; |
| 3668 |
params[B43_QOSPARAM_BSLOTS] = bslots; |
| 3669 |
params[B43_QOSPARAM_REGGAP] = bslots + p->aifs; |
| 3670 |
|
| 3671 |
for (i = 0; i < ARRAY_SIZE(params); i++) { |
| 3672 |
if (i == B43_QOSPARAM_STATUS) { |
| 3673 |
tmp = b43_shm_read16(dev, B43_SHM_SHARED, |
| 3674 |
shm_offset + (i * 2)); |
| 3675 |
/* Mark the parameters as updated. */ |
| 3676 |
tmp |= 0x100; |
| 3677 |
b43_shm_write16(dev, B43_SHM_SHARED, |
| 3678 |
shm_offset + (i * 2), |
| 3679 |
tmp); |
| 3680 |
} else { |
| 3681 |
b43_shm_write16(dev, B43_SHM_SHARED, |
| 3682 |
shm_offset + (i * 2), |
| 3683 |
params[i]); |
| 3684 |
} |
| 3685 |
} |
| 3686 |
} |
| 3687 |
|
| 3688 |
/* Mapping of mac80211 queue numbers to b43 QoS SHM offsets. */ |
| 3689 |
static const u16 b43_qos_shm_offsets[] = { |
| 3690 |
/* [mac80211-queue-nr] = SHM_OFFSET, */ |
| 3691 |
[0] = B43_QOS_VOICE, |
| 3692 |
[1] = B43_QOS_VIDEO, |
| 3693 |
[2] = B43_QOS_BESTEFFORT, |
| 3694 |
[3] = B43_QOS_BACKGROUND, |
| 3695 |
}; |
| 3696 |
|
| 3697 |
/* Update all QOS parameters in hardware. */ |
| 3698 |
static void b43_qos_upload_all(struct b43_wldev *dev) |
| 3699 |
{ |
| 3700 |
struct b43_wl *wl = dev->wl; |
| 3701 |
struct b43_qos_params *params; |
| 3702 |
unsigned int i; |
| 3703 |
|
| 3704 |
if (!dev->qos_enabled) |
| 3705 |
return; |
| 3706 |
|
| 3707 |
BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != |
| 3708 |
ARRAY_SIZE(wl->qos_params)); |
| 3709 |
|
| 3710 |
b43_mac_suspend(dev); |
| 3711 |
for (i = 0; i < ARRAY_SIZE(wl->qos_params); i++) { |
| 3712 |
params = &(wl->qos_params[i]); |
| 3713 |
b43_qos_params_upload(dev, &(params->p), |
| 3714 |
b43_qos_shm_offsets[i]); |
| 3715 |
} |
| 3716 |
b43_mac_enable(dev); |
| 3717 |
} |
| 3718 |
|
| 3719 |
static void b43_qos_clear(struct b43_wl *wl) |
| 3720 |
{ |
| 3721 |
struct b43_qos_params *params; |
| 3722 |
unsigned int i; |
| 3723 |
|
| 3724 |
/* Initialize QoS parameters to sane defaults. */ |
| 3725 |
|
| 3726 |
BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != |
| 3727 |
ARRAY_SIZE(wl->qos_params)); |
| 3728 |
|
| 3729 |
for (i = 0; i < ARRAY_SIZE(wl->qos_params); i++) { |
| 3730 |
params = &(wl->qos_params[i]); |
| 3731 |
|
| 3732 |
switch (b43_qos_shm_offsets[i]) { |
| 3733 |
case B43_QOS_VOICE: |
| 3734 |
params->p.txop = 0; |
| 3735 |
params->p.aifs = 2; |
| 3736 |
params->p.cw_min = 0x0001; |
| 3737 |
params->p.cw_max = 0x0001; |
| 3738 |
break; |
| 3739 |
case B43_QOS_VIDEO: |
| 3740 |
params->p.txop = 0; |
| 3741 |
params->p.aifs = 2; |
| 3742 |
params->p.cw_min = 0x0001; |
| 3743 |
params->p.cw_max = 0x0001; |
| 3744 |
break; |
| 3745 |
case B43_QOS_BESTEFFORT: |
| 3746 |
params->p.txop = 0; |
| 3747 |
params->p.aifs = 3; |
| 3748 |
params->p.cw_min = 0x0001; |
| 3749 |
params->p.cw_max = 0x03FF; |
| 3750 |
break; |
| 3751 |
case B43_QOS_BACKGROUND: |
| 3752 |
params->p.txop = 0; |
| 3753 |
params->p.aifs = 7; |
| 3754 |
params->p.cw_min = 0x0001; |
| 3755 |
params->p.cw_max = 0x03FF; |
| 3756 |
break; |
| 3757 |
default: |
| 3758 |
B43_WARN_ON(1); |
| 3759 |
} |
| 3760 |
} |
| 3761 |
} |
| 3762 |
|
| 3763 |
/* Initialize the core's QOS capabilities */ |
| 3764 |
static void b43_qos_init(struct b43_wldev *dev) |
| 3765 |
{ |
| 3766 |
if (!dev->qos_enabled) { |
| 3767 |
/* Disable QOS support. */ |
| 3768 |
b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_EDCF); |
| 3769 |
b43_write16(dev, B43_MMIO_IFSCTL, |
| 3770 |
b43_read16(dev, B43_MMIO_IFSCTL) |
| 3771 |
& ~B43_MMIO_IFSCTL_USE_EDCF); |
| 3772 |
b43dbg(dev->wl, "QoS disabled\n"); |
| 3773 |
return; |
| 3774 |
} |
| 3775 |
|
| 3776 |
/* Upload the current QOS parameters. */ |
| 3777 |
b43_qos_upload_all(dev); |
| 3778 |
|
| 3779 |
/* Enable QOS support. */ |
| 3780 |
b43_hf_write(dev, b43_hf_read(dev) | B43_HF_EDCF); |
| 3781 |
b43_write16(dev, B43_MMIO_IFSCTL, |
| 3782 |
b43_read16(dev, B43_MMIO_IFSCTL) |
| 3783 |
| B43_MMIO_IFSCTL_USE_EDCF); |
| 3784 |
b43dbg(dev->wl, "QoS enabled\n"); |
| 3785 |
} |
| 3786 |
|
| 3787 |
static int b43_op_conf_tx(struct ieee80211_hw *hw, |
| 3788 |
struct ieee80211_vif *vif, |
| 3789 |
unsigned int link_id, u16 _queue, |
| 3790 |
const struct ieee80211_tx_queue_params *params) |
| 3791 |
{ |
| 3792 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 3793 |
struct b43_wldev *dev; |
| 3794 |
unsigned int queue = (unsigned int)_queue; |
| 3795 |
int err = -ENODEV; |
| 3796 |
|
| 3797 |
if (queue >= ARRAY_SIZE(wl->qos_params)) { |
| 3798 |
/* Queue not available or don't support setting |
| 3799 |
* params on this queue. Return success to not |
| 3800 |
* confuse mac80211. */ |
| 3801 |
return 0; |
| 3802 |
} |
| 3803 |
BUILD_BUG_ON(ARRAY_SIZE(b43_qos_shm_offsets) != |
| 3804 |
ARRAY_SIZE(wl->qos_params)); |
| 3805 |
|
| 3806 |
mutex_lock(&wl->mutex); |
| 3807 |
dev = wl->current_dev; |
| 3808 |
if (unlikely(!dev || (b43_status(dev) < B43_STAT_INITIALIZED))) |
| 3809 |
goto out_unlock; |
| 3810 |
|
| 3811 |
memcpy(&(wl->qos_params[queue].p), params, sizeof(*params)); |
| 3812 |
b43_mac_suspend(dev); |
| 3813 |
b43_qos_params_upload(dev, &(wl->qos_params[queue].p), |
| 3814 |
b43_qos_shm_offsets[queue]); |
| 3815 |
b43_mac_enable(dev); |
| 3816 |
err = 0; |
| 3817 |
|
| 3818 |
out_unlock: |
| 3819 |
mutex_unlock(&wl->mutex); |
| 3820 |
|
| 3821 |
return err; |
| 3822 |
} |
| 3823 |
|
| 3824 |
static int b43_op_get_stats(struct ieee80211_hw *hw, |
| 3825 |
struct ieee80211_low_level_stats *stats) |
| 3826 |
{ |
| 3827 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 3828 |
|
| 3829 |
mutex_lock(&wl->mutex); |
| 3830 |
memcpy(stats, &wl->ieee_stats, sizeof(*stats)); |
| 3831 |
mutex_unlock(&wl->mutex); |
| 3832 |
|
| 3833 |
return 0; |
| 3834 |
} |
| 3835 |
|
| 3836 |
static u64 b43_op_get_tsf(struct ieee80211_hw *hw, struct ieee80211_vif *vif) |
| 3837 |
{ |
| 3838 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 3839 |
struct b43_wldev *dev; |
| 3840 |
u64 tsf; |
| 3841 |
|
| 3842 |
mutex_lock(&wl->mutex); |
| 3843 |
dev = wl->current_dev; |
| 3844 |
|
| 3845 |
if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) |
| 3846 |
b43_tsf_read(dev, &tsf); |
| 3847 |
else |
| 3848 |
tsf = 0; |
| 3849 |
|
| 3850 |
mutex_unlock(&wl->mutex); |
| 3851 |
|
| 3852 |
return tsf; |
| 3853 |
} |
| 3854 |
|
| 3855 |
static void b43_op_set_tsf(struct ieee80211_hw *hw, |
| 3856 |
struct ieee80211_vif *vif, u64 tsf) |
| 3857 |
{ |
| 3858 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 3859 |
struct b43_wldev *dev; |
| 3860 |
|
| 3861 |
mutex_lock(&wl->mutex); |
| 3862 |
dev = wl->current_dev; |
| 3863 |
|
| 3864 |
if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) |
| 3865 |
b43_tsf_write(dev, tsf); |
| 3866 |
|
| 3867 |
mutex_unlock(&wl->mutex); |
| 3868 |
} |
| 3869 |
|
| 3870 |
static const char *band_to_string(enum nl80211_band band) |
| 3871 |
{ |
| 3872 |
switch (band) { |
| 3873 |
case NL80211_BAND_5GHZ: |
| 3874 |
return "5"; |
| 3875 |
case NL80211_BAND_2GHZ: |
| 3876 |
return "2.4"; |
| 3877 |
default: |
| 3878 |
break; |
| 3879 |
} |
| 3880 |
B43_WARN_ON(1); |
| 3881 |
return ""; |
| 3882 |
} |
| 3883 |
|
| 3884 |
/* Expects wl->mutex locked */ |
| 3885 |
static int b43_switch_band(struct b43_wldev *dev, |
| 3886 |
struct ieee80211_channel *chan) |
| 3887 |
{ |
| 3888 |
struct b43_phy *phy = &dev->phy; |
| 3889 |
bool gmode; |
| 3890 |
u32 tmp; |
| 3891 |
|
| 3892 |
switch (chan->band) { |
| 3893 |
case NL80211_BAND_5GHZ: |
| 3894 |
gmode = false; |
| 3895 |
break; |
| 3896 |
case NL80211_BAND_2GHZ: |
| 3897 |
gmode = true; |
| 3898 |
break; |
| 3899 |
default: |
| 3900 |
B43_WARN_ON(1); |
| 3901 |
return -EINVAL; |
| 3902 |
} |
| 3903 |
|
| 3904 |
if (!((gmode && phy->supports_2ghz) || |
| 3905 |
(!gmode && phy->supports_5ghz))) { |
| 3906 |
b43err(dev->wl, "This device doesn't support %s-GHz band\n", |
| 3907 |
band_to_string(chan->band)); |
| 3908 |
return -ENODEV; |
| 3909 |
} |
| 3910 |
|
| 3911 |
if (!!phy->gmode == !!gmode) { |
| 3912 |
/* This device is already running. */ |
| 3913 |
return 0; |
| 3914 |
} |
| 3915 |
|
| 3916 |
b43dbg(dev->wl, "Switching to %s GHz band\n", |
| 3917 |
band_to_string(chan->band)); |
| 3918 |
|
| 3919 |
/* Some new devices don't need disabling radio for band switching */ |
| 3920 |
if (!(phy->type == B43_PHYTYPE_N && phy->rev >= 3)) |
| 3921 |
b43_software_rfkill(dev, true); |
| 3922 |
|
| 3923 |
phy->gmode = gmode; |
| 3924 |
b43_phy_put_into_reset(dev); |
| 3925 |
switch (dev->dev->bus_type) { |
| 3926 |
#ifdef CONFIG_B43_BCMA |
| 3927 |
case B43_BUS_BCMA: |
| 3928 |
tmp = bcma_aread32(dev->dev->bdev, BCMA_IOCTL); |
| 3929 |
if (gmode) |
| 3930 |
tmp |= B43_BCMA_IOCTL_GMODE; |
| 3931 |
else |
| 3932 |
tmp &= ~B43_BCMA_IOCTL_GMODE; |
| 3933 |
bcma_awrite32(dev->dev->bdev, BCMA_IOCTL, tmp); |
| 3934 |
break; |
| 3935 |
#endif |
| 3936 |
#ifdef CONFIG_B43_SSB |
| 3937 |
case B43_BUS_SSB: |
| 3938 |
tmp = ssb_read32(dev->dev->sdev, SSB_TMSLOW); |
| 3939 |
if (gmode) |
| 3940 |
tmp |= B43_TMSLOW_GMODE; |
| 3941 |
else |
| 3942 |
tmp &= ~B43_TMSLOW_GMODE; |
| 3943 |
ssb_write32(dev->dev->sdev, SSB_TMSLOW, tmp); |
| 3944 |
break; |
| 3945 |
#endif |
| 3946 |
} |
| 3947 |
b43_phy_take_out_of_reset(dev); |
| 3948 |
|
| 3949 |
b43_upload_initvals_band(dev); |
| 3950 |
|
| 3951 |
b43_phy_init(dev); |
| 3952 |
|
| 3953 |
return 0; |
| 3954 |
} |
| 3955 |
|
| 3956 |
static void b43_set_beacon_listen_interval(struct b43_wldev *dev, u16 interval) |
| 3957 |
{ |
| 3958 |
interval = min_t(u16, interval, (u16)0xFF); |
| 3959 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_BCN_LI, interval); |
| 3960 |
} |
| 3961 |
|
| 3962 |
/* Write the short and long frame retry limit values. */ |
| 3963 |
static void b43_set_retry_limits(struct b43_wldev *dev, |
| 3964 |
unsigned int short_retry, |
| 3965 |
unsigned int long_retry) |
| 3966 |
{ |
| 3967 |
/* The retry limit is a 4-bit counter. Enforce this to avoid overflowing |
| 3968 |
* the chip-internal counter. */ |
| 3969 |
short_retry = min(short_retry, (unsigned int)0xF); |
| 3970 |
long_retry = min(long_retry, (unsigned int)0xF); |
| 3971 |
|
| 3972 |
b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_SRLIMIT, |
| 3973 |
short_retry); |
| 3974 |
b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_LRLIMIT, |
| 3975 |
long_retry); |
| 3976 |
} |
| 3977 |
|
| 3978 |
static int b43_op_config(struct ieee80211_hw *hw, int radio_idx, u32 changed) |
| 3979 |
{ |
| 3980 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 3981 |
struct b43_wldev *dev = wl->current_dev; |
| 3982 |
struct b43_phy *phy = &dev->phy; |
| 3983 |
struct ieee80211_conf *conf = &hw->conf; |
| 3984 |
int antenna; |
| 3985 |
int err = 0; |
| 3986 |
|
| 3987 |
mutex_lock(&wl->mutex); |
| 3988 |
b43_mac_suspend(dev); |
| 3989 |
|
| 3990 |
if (changed & IEEE80211_CONF_CHANGE_LISTEN_INTERVAL) |
| 3991 |
b43_set_beacon_listen_interval(dev, conf->listen_interval); |
| 3992 |
|
| 3993 |
if (changed & IEEE80211_CONF_CHANGE_CHANNEL) { |
| 3994 |
phy->chandef = &conf->chandef; |
| 3995 |
phy->channel = conf->chandef.chan->hw_value; |
| 3996 |
|
| 3997 |
/* Switch the band (if necessary). */ |
| 3998 |
err = b43_switch_band(dev, conf->chandef.chan); |
| 3999 |
if (err) |
| 4000 |
goto out_mac_enable; |
| 4001 |
|
| 4002 |
/* Switch to the requested channel. |
| 4003 |
* The firmware takes care of races with the TX handler. |
| 4004 |
*/ |
| 4005 |
b43_switch_channel(dev, phy->channel); |
| 4006 |
} |
| 4007 |
|
| 4008 |
if (changed & IEEE80211_CONF_CHANGE_RETRY_LIMITS) |
| 4009 |
b43_set_retry_limits(dev, conf->short_frame_max_tx_count, |
| 4010 |
conf->long_frame_max_tx_count); |
| 4011 |
changed &= ~IEEE80211_CONF_CHANGE_RETRY_LIMITS; |
| 4012 |
if (!changed) |
| 4013 |
goto out_mac_enable; |
| 4014 |
|
| 4015 |
dev->wl->radiotap_enabled = !!(conf->flags & IEEE80211_CONF_MONITOR); |
| 4016 |
|
| 4017 |
/* Adjust the desired TX power level. */ |
| 4018 |
if (conf->power_level != 0) { |
| 4019 |
if (conf->power_level != phy->desired_txpower) { |
| 4020 |
phy->desired_txpower = conf->power_level; |
| 4021 |
b43_phy_txpower_check(dev, B43_TXPWR_IGNORE_TIME | |
| 4022 |
B43_TXPWR_IGNORE_TSSI); |
| 4023 |
} |
| 4024 |
} |
| 4025 |
|
| 4026 |
/* Antennas for RX and management frame TX. */ |
| 4027 |
antenna = B43_ANTENNA_DEFAULT; |
| 4028 |
b43_mgmtframe_txantenna(dev, antenna); |
| 4029 |
antenna = B43_ANTENNA_DEFAULT; |
| 4030 |
if (phy->ops->set_rx_antenna) |
| 4031 |
phy->ops->set_rx_antenna(dev, antenna); |
| 4032 |
|
| 4033 |
if (wl->radio_enabled != phy->radio_on) { |
| 4034 |
if (wl->radio_enabled) { |
| 4035 |
b43_software_rfkill(dev, false); |
| 4036 |
b43info(dev->wl, "Radio turned on by software\n"); |
| 4037 |
if (!dev->radio_hw_enable) { |
| 4038 |
b43info(dev->wl, "The hardware RF-kill button " |
| 4039 |
"still turns the radio physically off. " |
| 4040 |
"Press the button to turn it on.\n"); |
| 4041 |
} |
| 4042 |
} else { |
| 4043 |
b43_software_rfkill(dev, true); |
| 4044 |
b43info(dev->wl, "Radio turned off by software\n"); |
| 4045 |
} |
| 4046 |
} |
| 4047 |
|
| 4048 |
out_mac_enable: |
| 4049 |
b43_mac_enable(dev); |
| 4050 |
mutex_unlock(&wl->mutex); |
| 4051 |
|
| 4052 |
return err; |
| 4053 |
} |
| 4054 |
|
| 4055 |
static void b43_update_basic_rates(struct b43_wldev *dev, u32 brates) |
| 4056 |
{ |
| 4057 |
struct ieee80211_supported_band *sband = |
| 4058 |
dev->wl->hw->wiphy->bands[b43_current_band(dev->wl)]; |
| 4059 |
const struct ieee80211_rate *rate; |
| 4060 |
int i; |
| 4061 |
u16 basic, direct, offset, basic_offset, rateptr; |
| 4062 |
|
| 4063 |
for (i = 0; i < sband->n_bitrates; i++) { |
| 4064 |
rate = &sband->bitrates[i]; |
| 4065 |
|
| 4066 |
if (b43_is_cck_rate(rate->hw_value)) { |
| 4067 |
direct = B43_SHM_SH_CCKDIRECT; |
| 4068 |
basic = B43_SHM_SH_CCKBASIC; |
| 4069 |
offset = b43_plcp_get_ratecode_cck(rate->hw_value); |
| 4070 |
offset &= 0xF; |
| 4071 |
} else { |
| 4072 |
direct = B43_SHM_SH_OFDMDIRECT; |
| 4073 |
basic = B43_SHM_SH_OFDMBASIC; |
| 4074 |
offset = b43_plcp_get_ratecode_ofdm(rate->hw_value); |
| 4075 |
offset &= 0xF; |
| 4076 |
} |
| 4077 |
|
| 4078 |
rate = ieee80211_get_response_rate(sband, brates, rate->bitrate); |
| 4079 |
|
| 4080 |
if (b43_is_cck_rate(rate->hw_value)) { |
| 4081 |
basic_offset = b43_plcp_get_ratecode_cck(rate->hw_value); |
| 4082 |
basic_offset &= 0xF; |
| 4083 |
} else { |
| 4084 |
basic_offset = b43_plcp_get_ratecode_ofdm(rate->hw_value); |
| 4085 |
basic_offset &= 0xF; |
| 4086 |
} |
| 4087 |
|
| 4088 |
/* |
| 4089 |
* Get the pointer that we need to point to |
| 4090 |
* from the direct map |
| 4091 |
*/ |
| 4092 |
rateptr = b43_shm_read16(dev, B43_SHM_SHARED, |
| 4093 |
direct + 2 * basic_offset); |
| 4094 |
/* and write it to the basic map */ |
| 4095 |
b43_shm_write16(dev, B43_SHM_SHARED, basic + 2 * offset, |
| 4096 |
rateptr); |
| 4097 |
} |
| 4098 |
} |
| 4099 |
|
| 4100 |
static void b43_op_bss_info_changed(struct ieee80211_hw *hw, |
| 4101 |
struct ieee80211_vif *vif, |
| 4102 |
struct ieee80211_bss_conf *conf, |
| 4103 |
u64 changed) |
| 4104 |
{ |
| 4105 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 4106 |
struct b43_wldev *dev; |
| 4107 |
|
| 4108 |
mutex_lock(&wl->mutex); |
| 4109 |
|
| 4110 |
dev = wl->current_dev; |
| 4111 |
if (!dev || b43_status(dev) < B43_STAT_STARTED) |
| 4112 |
goto out_unlock_mutex; |
| 4113 |
|
| 4114 |
B43_WARN_ON(wl->vif != vif); |
| 4115 |
|
| 4116 |
if (changed & BSS_CHANGED_BSSID) { |
| 4117 |
if (conf->bssid) |
| 4118 |
memcpy(wl->bssid, conf->bssid, ETH_ALEN); |
| 4119 |
else |
| 4120 |
eth_zero_addr(wl->bssid); |
| 4121 |
} |
| 4122 |
|
| 4123 |
if (b43_status(dev) >= B43_STAT_INITIALIZED) { |
| 4124 |
if (changed & BSS_CHANGED_BEACON && |
| 4125 |
(b43_is_mode(wl, NL80211_IFTYPE_AP) || |
| 4126 |
b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) || |
| 4127 |
b43_is_mode(wl, NL80211_IFTYPE_ADHOC))) |
| 4128 |
b43_update_templates(wl); |
| 4129 |
|
| 4130 |
if (changed & BSS_CHANGED_BSSID) |
| 4131 |
b43_write_mac_bssid_templates(dev); |
| 4132 |
} |
| 4133 |
|
| 4134 |
b43_mac_suspend(dev); |
| 4135 |
|
| 4136 |
/* Update templates for AP/mesh mode. */ |
| 4137 |
if (changed & BSS_CHANGED_BEACON_INT && |
| 4138 |
(b43_is_mode(wl, NL80211_IFTYPE_AP) || |
| 4139 |
b43_is_mode(wl, NL80211_IFTYPE_MESH_POINT) || |
| 4140 |
b43_is_mode(wl, NL80211_IFTYPE_ADHOC)) && |
| 4141 |
conf->beacon_int) |
| 4142 |
b43_set_beacon_int(dev, conf->beacon_int); |
| 4143 |
|
| 4144 |
if (changed & BSS_CHANGED_BASIC_RATES) |
| 4145 |
b43_update_basic_rates(dev, conf->basic_rates); |
| 4146 |
|
| 4147 |
if (changed & BSS_CHANGED_ERP_SLOT) { |
| 4148 |
if (conf->use_short_slot) |
| 4149 |
b43_short_slot_timing_enable(dev); |
| 4150 |
else |
| 4151 |
b43_short_slot_timing_disable(dev); |
| 4152 |
} |
| 4153 |
|
| 4154 |
b43_mac_enable(dev); |
| 4155 |
out_unlock_mutex: |
| 4156 |
mutex_unlock(&wl->mutex); |
| 4157 |
} |
| 4158 |
|
| 4159 |
static int b43_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, |
| 4160 |
struct ieee80211_vif *vif, struct ieee80211_sta *sta, |
| 4161 |
struct ieee80211_key_conf *key) |
| 4162 |
{ |
| 4163 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 4164 |
struct b43_wldev *dev; |
| 4165 |
u8 algorithm; |
| 4166 |
u8 index; |
| 4167 |
int err; |
| 4168 |
static const u8 bcast_addr[ETH_ALEN] = { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff }; |
| 4169 |
|
| 4170 |
if (modparam_nohwcrypt) |
| 4171 |
return -ENOSPC; /* User disabled HW-crypto */ |
| 4172 |
|
| 4173 |
if ((vif->type == NL80211_IFTYPE_ADHOC || |
| 4174 |
vif->type == NL80211_IFTYPE_MESH_POINT) && |
| 4175 |
(key->cipher == WLAN_CIPHER_SUITE_TKIP || |
| 4176 |
key->cipher == WLAN_CIPHER_SUITE_CCMP) && |
| 4177 |
!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)) { |
| 4178 |
/* |
| 4179 |
* For now, disable hw crypto for the RSN IBSS group keys. This |
| 4180 |
* could be optimized in the future, but until that gets |
| 4181 |
* implemented, use of software crypto for group addressed |
| 4182 |
* frames is a acceptable to allow RSN IBSS to be used. |
| 4183 |
*/ |
| 4184 |
return -EOPNOTSUPP; |
| 4185 |
} |
| 4186 |
|
| 4187 |
mutex_lock(&wl->mutex); |
| 4188 |
|
| 4189 |
dev = wl->current_dev; |
| 4190 |
err = -ENODEV; |
| 4191 |
if (!dev || b43_status(dev) < B43_STAT_INITIALIZED) |
| 4192 |
goto out_unlock; |
| 4193 |
|
| 4194 |
if (dev->fw.pcm_request_failed || !dev->hwcrypto_enabled) { |
| 4195 |
/* We don't have firmware for the crypto engine. |
| 4196 |
* Must use software-crypto. */ |
| 4197 |
err = -EOPNOTSUPP; |
| 4198 |
goto out_unlock; |
| 4199 |
} |
| 4200 |
|
| 4201 |
err = -EINVAL; |
| 4202 |
switch (key->cipher) { |
| 4203 |
case WLAN_CIPHER_SUITE_WEP40: |
| 4204 |
algorithm = B43_SEC_ALGO_WEP40; |
| 4205 |
break; |
| 4206 |
case WLAN_CIPHER_SUITE_WEP104: |
| 4207 |
algorithm = B43_SEC_ALGO_WEP104; |
| 4208 |
break; |
| 4209 |
case WLAN_CIPHER_SUITE_TKIP: |
| 4210 |
algorithm = B43_SEC_ALGO_TKIP; |
| 4211 |
break; |
| 4212 |
case WLAN_CIPHER_SUITE_CCMP: |
| 4213 |
algorithm = B43_SEC_ALGO_AES; |
| 4214 |
break; |
| 4215 |
default: |
| 4216 |
B43_WARN_ON(1); |
| 4217 |
goto out_unlock; |
| 4218 |
} |
| 4219 |
index = (u8) (key->keyidx); |
| 4220 |
if (index > 3) |
| 4221 |
goto out_unlock; |
| 4222 |
|
| 4223 |
switch (cmd) { |
| 4224 |
case SET_KEY: |
| 4225 |
if (algorithm == B43_SEC_ALGO_TKIP && |
| 4226 |
(!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE) || |
| 4227 |
!modparam_hwtkip)) { |
| 4228 |
/* We support only pairwise key */ |
| 4229 |
err = -EOPNOTSUPP; |
| 4230 |
goto out_unlock; |
| 4231 |
} |
| 4232 |
|
| 4233 |
if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) { |
| 4234 |
if (WARN_ON(!sta)) { |
| 4235 |
err = -EOPNOTSUPP; |
| 4236 |
goto out_unlock; |
| 4237 |
} |
| 4238 |
/* Pairwise key with an assigned MAC address. */ |
| 4239 |
err = b43_key_write(dev, -1, algorithm, |
| 4240 |
key->key, key->keylen, |
| 4241 |
sta->addr, key); |
| 4242 |
} else { |
| 4243 |
/* Group key */ |
| 4244 |
err = b43_key_write(dev, index, algorithm, |
| 4245 |
key->key, key->keylen, NULL, key); |
| 4246 |
} |
| 4247 |
if (err) |
| 4248 |
goto out_unlock; |
| 4249 |
|
| 4250 |
if (algorithm == B43_SEC_ALGO_WEP40 || |
| 4251 |
algorithm == B43_SEC_ALGO_WEP104) { |
| 4252 |
b43_hf_write(dev, b43_hf_read(dev) | B43_HF_USEDEFKEYS); |
| 4253 |
} else { |
| 4254 |
b43_hf_write(dev, |
| 4255 |
b43_hf_read(dev) & ~B43_HF_USEDEFKEYS); |
| 4256 |
} |
| 4257 |
key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| 4258 |
if (algorithm == B43_SEC_ALGO_TKIP) |
| 4259 |
key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; |
| 4260 |
break; |
| 4261 |
case DISABLE_KEY: { |
| 4262 |
err = b43_key_clear(dev, key->hw_key_idx); |
| 4263 |
if (err) |
| 4264 |
goto out_unlock; |
| 4265 |
break; |
| 4266 |
} |
| 4267 |
default: |
| 4268 |
B43_WARN_ON(1); |
| 4269 |
} |
| 4270 |
|
| 4271 |
out_unlock: |
| 4272 |
if (!err) { |
| 4273 |
b43dbg(wl, "%s hardware based encryption for keyidx: %d, " |
| 4274 |
"mac: %pM\n", |
| 4275 |
cmd == SET_KEY ? "Using" : "Disabling", key->keyidx, |
| 4276 |
sta ? sta->addr : bcast_addr); |
| 4277 |
b43_dump_keymemory(dev); |
| 4278 |
} |
| 4279 |
mutex_unlock(&wl->mutex); |
| 4280 |
|
| 4281 |
return err; |
| 4282 |
} |
| 4283 |
|
| 4284 |
static void b43_op_configure_filter(struct ieee80211_hw *hw, |
| 4285 |
unsigned int changed, unsigned int *fflags, |
| 4286 |
u64 multicast) |
| 4287 |
{ |
| 4288 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 4289 |
struct b43_wldev *dev; |
| 4290 |
|
| 4291 |
mutex_lock(&wl->mutex); |
| 4292 |
dev = wl->current_dev; |
| 4293 |
if (!dev) { |
| 4294 |
*fflags = 0; |
| 4295 |
goto out_unlock; |
| 4296 |
} |
| 4297 |
|
| 4298 |
*fflags &= FIF_ALLMULTI | |
| 4299 |
FIF_FCSFAIL | |
| 4300 |
FIF_PLCPFAIL | |
| 4301 |
FIF_CONTROL | |
| 4302 |
FIF_OTHER_BSS | |
| 4303 |
FIF_BCN_PRBRESP_PROMISC; |
| 4304 |
|
| 4305 |
changed &= FIF_ALLMULTI | |
| 4306 |
FIF_FCSFAIL | |
| 4307 |
FIF_PLCPFAIL | |
| 4308 |
FIF_CONTROL | |
| 4309 |
FIF_OTHER_BSS | |
| 4310 |
FIF_BCN_PRBRESP_PROMISC; |
| 4311 |
|
| 4312 |
wl->filter_flags = *fflags; |
| 4313 |
|
| 4314 |
if (changed && b43_status(dev) >= B43_STAT_INITIALIZED) |
| 4315 |
b43_adjust_opmode(dev); |
| 4316 |
|
| 4317 |
out_unlock: |
| 4318 |
mutex_unlock(&wl->mutex); |
| 4319 |
} |
| 4320 |
|
| 4321 |
/* Locking: wl->mutex |
| 4322 |
* Returns the current dev. This might be different from the passed in dev, |
| 4323 |
* because the core might be gone away while we unlocked the mutex. */ |
| 4324 |
static struct b43_wldev * b43_wireless_core_stop(struct b43_wldev *dev) |
| 4325 |
{ |
| 4326 |
struct b43_wl *wl; |
| 4327 |
struct b43_wldev *orig_dev; |
| 4328 |
u32 mask; |
| 4329 |
int queue_num; |
| 4330 |
|
| 4331 |
if (!dev) |
| 4332 |
return NULL; |
| 4333 |
wl = dev->wl; |
| 4334 |
redo: |
| 4335 |
if (!dev || b43_status(dev) < B43_STAT_STARTED) |
| 4336 |
return dev; |
| 4337 |
|
| 4338 |
/* Cancel work. Unlock to avoid deadlocks. */ |
| 4339 |
mutex_unlock(&wl->mutex); |
| 4340 |
cancel_delayed_work_sync(&dev->periodic_work); |
| 4341 |
cancel_work_sync(&wl->tx_work); |
| 4342 |
b43_leds_stop(dev); |
| 4343 |
mutex_lock(&wl->mutex); |
| 4344 |
dev = wl->current_dev; |
| 4345 |
if (!dev || b43_status(dev) < B43_STAT_STARTED) { |
| 4346 |
/* Whoops, aliens ate up the device while we were unlocked. */ |
| 4347 |
return dev; |
| 4348 |
} |
| 4349 |
|
| 4350 |
/* Disable interrupts on the device. */ |
| 4351 |
b43_set_status(dev, B43_STAT_INITIALIZED); |
| 4352 |
if (b43_bus_host_is_sdio(dev->dev)) { |
| 4353 |
/* wl->mutex is locked. That is enough. */ |
| 4354 |
b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); |
| 4355 |
b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */ |
| 4356 |
} else { |
| 4357 |
spin_lock_irq(&wl->hardirq_lock); |
| 4358 |
b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); |
| 4359 |
b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */ |
| 4360 |
spin_unlock_irq(&wl->hardirq_lock); |
| 4361 |
} |
| 4362 |
/* Synchronize and free the interrupt handlers. Unlock to avoid deadlocks. */ |
| 4363 |
orig_dev = dev; |
| 4364 |
mutex_unlock(&wl->mutex); |
| 4365 |
if (b43_bus_host_is_sdio(dev->dev)) |
| 4366 |
b43_sdio_free_irq(dev); |
| 4367 |
else |
| 4368 |
free_irq(dev->dev->irq, dev); |
| 4369 |
mutex_lock(&wl->mutex); |
| 4370 |
dev = wl->current_dev; |
| 4371 |
if (!dev) |
| 4372 |
return dev; |
| 4373 |
if (dev != orig_dev) { |
| 4374 |
if (b43_status(dev) >= B43_STAT_STARTED) |
| 4375 |
goto redo; |
| 4376 |
return dev; |
| 4377 |
} |
| 4378 |
mask = b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); |
| 4379 |
B43_WARN_ON(mask != 0xFFFFFFFF && mask); |
| 4380 |
|
| 4381 |
/* Drain all TX queues. */ |
| 4382 |
for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { |
| 4383 |
while (skb_queue_len(&wl->tx_queue[queue_num])) { |
| 4384 |
struct sk_buff *skb; |
| 4385 |
|
| 4386 |
skb = skb_dequeue(&wl->tx_queue[queue_num]); |
| 4387 |
ieee80211_free_txskb(wl->hw, skb); |
| 4388 |
} |
| 4389 |
} |
| 4390 |
|
| 4391 |
b43_mac_suspend(dev); |
| 4392 |
b43_leds_exit(dev); |
| 4393 |
b43dbg(wl, "Wireless interface stopped\n"); |
| 4394 |
|
| 4395 |
return dev; |
| 4396 |
} |
| 4397 |
|
| 4398 |
/* Locking: wl->mutex */ |
| 4399 |
static int b43_wireless_core_start(struct b43_wldev *dev) |
| 4400 |
{ |
| 4401 |
int err; |
| 4402 |
|
| 4403 |
B43_WARN_ON(b43_status(dev) != B43_STAT_INITIALIZED); |
| 4404 |
|
| 4405 |
drain_txstatus_queue(dev); |
| 4406 |
if (b43_bus_host_is_sdio(dev->dev)) { |
| 4407 |
err = b43_sdio_request_irq(dev, b43_sdio_interrupt_handler); |
| 4408 |
if (err) { |
| 4409 |
b43err(dev->wl, "Cannot request SDIO IRQ\n"); |
| 4410 |
goto out; |
| 4411 |
} |
| 4412 |
} else { |
| 4413 |
err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler, |
| 4414 |
b43_interrupt_thread_handler, |
| 4415 |
IRQF_SHARED, KBUILD_MODNAME, dev); |
| 4416 |
if (err) { |
| 4417 |
b43err(dev->wl, "Cannot request IRQ-%d\n", |
| 4418 |
dev->dev->irq); |
| 4419 |
goto out; |
| 4420 |
} |
| 4421 |
} |
| 4422 |
|
| 4423 |
/* We are ready to run. */ |
| 4424 |
ieee80211_wake_queues(dev->wl->hw); |
| 4425 |
b43_set_status(dev, B43_STAT_STARTED); |
| 4426 |
|
| 4427 |
/* Start data flow (TX/RX). */ |
| 4428 |
b43_mac_enable(dev); |
| 4429 |
b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); |
| 4430 |
|
| 4431 |
/* Start maintenance work */ |
| 4432 |
b43_periodic_tasks_setup(dev); |
| 4433 |
|
| 4434 |
b43_leds_init(dev); |
| 4435 |
|
| 4436 |
b43dbg(dev->wl, "Wireless interface started\n"); |
| 4437 |
out: |
| 4438 |
return err; |
| 4439 |
} |
| 4440 |
|
| 4441 |
static char *b43_phy_name(struct b43_wldev *dev, u8 phy_type) |
| 4442 |
{ |
| 4443 |
switch (phy_type) { |
| 4444 |
case B43_PHYTYPE_A: |
| 4445 |
return "A"; |
| 4446 |
case B43_PHYTYPE_B: |
| 4447 |
return "B"; |
| 4448 |
case B43_PHYTYPE_G: |
| 4449 |
return "G"; |
| 4450 |
case B43_PHYTYPE_N: |
| 4451 |
return "N"; |
| 4452 |
case B43_PHYTYPE_LP: |
| 4453 |
return "LP"; |
| 4454 |
case B43_PHYTYPE_SSLPN: |
| 4455 |
return "SSLPN"; |
| 4456 |
case B43_PHYTYPE_HT: |
| 4457 |
return "HT"; |
| 4458 |
case B43_PHYTYPE_LCN: |
| 4459 |
return "LCN"; |
| 4460 |
case B43_PHYTYPE_LCNXN: |
| 4461 |
return "LCNXN"; |
| 4462 |
case B43_PHYTYPE_LCN40: |
| 4463 |
return "LCN40"; |
| 4464 |
case B43_PHYTYPE_AC: |
| 4465 |
return "AC"; |
| 4466 |
} |
| 4467 |
return "UNKNOWN"; |
| 4468 |
} |
| 4469 |
|
| 4470 |
/* Get PHY and RADIO versioning numbers */ |
| 4471 |
static int b43_phy_versioning(struct b43_wldev *dev) |
| 4472 |
{ |
| 4473 |
struct b43_phy *phy = &dev->phy; |
| 4474 |
const u8 core_rev = dev->dev->core_rev; |
| 4475 |
u32 tmp; |
| 4476 |
u8 analog_type; |
| 4477 |
u8 phy_type; |
| 4478 |
u8 phy_rev; |
| 4479 |
u16 radio_manuf; |
| 4480 |
u16 radio_id; |
| 4481 |
u16 radio_rev; |
| 4482 |
u8 radio_ver; |
| 4483 |
int unsupported = 0; |
| 4484 |
|
| 4485 |
/* Get PHY versioning */ |
| 4486 |
tmp = b43_read16(dev, B43_MMIO_PHY_VER); |
| 4487 |
analog_type = (tmp & B43_PHYVER_ANALOG) >> B43_PHYVER_ANALOG_SHIFT; |
| 4488 |
phy_type = (tmp & B43_PHYVER_TYPE) >> B43_PHYVER_TYPE_SHIFT; |
| 4489 |
phy_rev = (tmp & B43_PHYVER_VERSION); |
| 4490 |
|
| 4491 |
/* LCNXN is continuation of N which run out of revisions */ |
| 4492 |
if (phy_type == B43_PHYTYPE_LCNXN) { |
| 4493 |
phy_type = B43_PHYTYPE_N; |
| 4494 |
phy_rev += 16; |
| 4495 |
} |
| 4496 |
|
| 4497 |
switch (phy_type) { |
| 4498 |
#ifdef CONFIG_B43_PHY_G |
| 4499 |
case B43_PHYTYPE_G: |
| 4500 |
if (phy_rev > 9) |
| 4501 |
unsupported = 1; |
| 4502 |
break; |
| 4503 |
#endif |
| 4504 |
#ifdef CONFIG_B43_PHY_N |
| 4505 |
case B43_PHYTYPE_N: |
| 4506 |
if (phy_rev >= 19) |
| 4507 |
unsupported = 1; |
| 4508 |
break; |
| 4509 |
#endif |
| 4510 |
#ifdef CONFIG_B43_PHY_LP |
| 4511 |
case B43_PHYTYPE_LP: |
| 4512 |
if (phy_rev > 2) |
| 4513 |
unsupported = 1; |
| 4514 |
break; |
| 4515 |
#endif |
| 4516 |
#ifdef CONFIG_B43_PHY_HT |
| 4517 |
case B43_PHYTYPE_HT: |
| 4518 |
if (phy_rev > 1) |
| 4519 |
unsupported = 1; |
| 4520 |
break; |
| 4521 |
#endif |
| 4522 |
#ifdef CONFIG_B43_PHY_LCN |
| 4523 |
case B43_PHYTYPE_LCN: |
| 4524 |
if (phy_rev > 1) |
| 4525 |
unsupported = 1; |
| 4526 |
break; |
| 4527 |
#endif |
| 4528 |
#ifdef CONFIG_B43_PHY_AC |
| 4529 |
case B43_PHYTYPE_AC: |
| 4530 |
if (phy_rev > 1) |
| 4531 |
unsupported = 1; |
| 4532 |
break; |
| 4533 |
#endif |
| 4534 |
default: |
| 4535 |
unsupported = 1; |
| 4536 |
} |
| 4537 |
if (unsupported) { |
| 4538 |
b43err(dev->wl, "FOUND UNSUPPORTED PHY (Analog %u, Type %d (%s), Revision %u)\n", |
| 4539 |
analog_type, phy_type, b43_phy_name(dev, phy_type), |
| 4540 |
phy_rev); |
| 4541 |
return -EOPNOTSUPP; |
| 4542 |
} |
| 4543 |
b43info(dev->wl, "Found PHY: Analog %u, Type %d (%s), Revision %u\n", |
| 4544 |
analog_type, phy_type, b43_phy_name(dev, phy_type), phy_rev); |
| 4545 |
|
| 4546 |
/* Get RADIO versioning */ |
| 4547 |
if (core_rev == 40 || core_rev == 42) { |
| 4548 |
radio_manuf = 0x17F; |
| 4549 |
|
| 4550 |
b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, 0); |
| 4551 |
radio_rev = b43_read16(dev, B43_MMIO_RADIO24_DATA); |
| 4552 |
|
| 4553 |
b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, 1); |
| 4554 |
radio_id = b43_read16(dev, B43_MMIO_RADIO24_DATA); |
| 4555 |
|
| 4556 |
radio_ver = 0; /* Is there version somewhere? */ |
| 4557 |
} else if (core_rev >= 24) { |
| 4558 |
u16 radio24[3]; |
| 4559 |
|
| 4560 |
for (tmp = 0; tmp < 3; tmp++) { |
| 4561 |
b43_write16f(dev, B43_MMIO_RADIO24_CONTROL, tmp); |
| 4562 |
radio24[tmp] = b43_read16(dev, B43_MMIO_RADIO24_DATA); |
| 4563 |
} |
| 4564 |
|
| 4565 |
radio_manuf = 0x17F; |
| 4566 |
radio_id = (radio24[2] << 8) | radio24[1]; |
| 4567 |
radio_rev = (radio24[0] & 0xF); |
| 4568 |
radio_ver = (radio24[0] & 0xF0) >> 4; |
| 4569 |
} else { |
| 4570 |
if (dev->dev->chip_id == 0x4317) { |
| 4571 |
if (dev->dev->chip_rev == 0) |
| 4572 |
tmp = 0x3205017F; |
| 4573 |
else if (dev->dev->chip_rev == 1) |
| 4574 |
tmp = 0x4205017F; |
| 4575 |
else |
| 4576 |
tmp = 0x5205017F; |
| 4577 |
} else { |
| 4578 |
b43_write16f(dev, B43_MMIO_RADIO_CONTROL, |
| 4579 |
B43_RADIOCTL_ID); |
| 4580 |
tmp = b43_read16(dev, B43_MMIO_RADIO_DATA_LOW); |
| 4581 |
b43_write16f(dev, B43_MMIO_RADIO_CONTROL, |
| 4582 |
B43_RADIOCTL_ID); |
| 4583 |
tmp |= b43_read16(dev, B43_MMIO_RADIO_DATA_HIGH) << 16; |
| 4584 |
} |
| 4585 |
radio_manuf = (tmp & 0x00000FFF); |
| 4586 |
radio_id = (tmp & 0x0FFFF000) >> 12; |
| 4587 |
radio_rev = (tmp & 0xF0000000) >> 28; |
| 4588 |
radio_ver = 0; /* Probably not available on old hw */ |
| 4589 |
} |
| 4590 |
|
| 4591 |
if (radio_manuf != 0x17F /* Broadcom */) |
| 4592 |
unsupported = 1; |
| 4593 |
switch (phy_type) { |
| 4594 |
case B43_PHYTYPE_B: |
| 4595 |
if ((radio_id & 0xFFF0) != 0x2050) |
| 4596 |
unsupported = 1; |
| 4597 |
break; |
| 4598 |
case B43_PHYTYPE_G: |
| 4599 |
if (radio_id != 0x2050) |
| 4600 |
unsupported = 1; |
| 4601 |
break; |
| 4602 |
case B43_PHYTYPE_N: |
| 4603 |
if (radio_id != 0x2055 && radio_id != 0x2056 && |
| 4604 |
radio_id != 0x2057) |
| 4605 |
unsupported = 1; |
| 4606 |
if (radio_id == 0x2057 && |
| 4607 |
!(radio_rev == 9 || radio_rev == 14)) |
| 4608 |
unsupported = 1; |
| 4609 |
break; |
| 4610 |
case B43_PHYTYPE_LP: |
| 4611 |
if (radio_id != 0x2062 && radio_id != 0x2063) |
| 4612 |
unsupported = 1; |
| 4613 |
break; |
| 4614 |
case B43_PHYTYPE_HT: |
| 4615 |
if (radio_id != 0x2059) |
| 4616 |
unsupported = 1; |
| 4617 |
break; |
| 4618 |
case B43_PHYTYPE_LCN: |
| 4619 |
if (radio_id != 0x2064) |
| 4620 |
unsupported = 1; |
| 4621 |
break; |
| 4622 |
case B43_PHYTYPE_AC: |
| 4623 |
if (radio_id != 0x2069) |
| 4624 |
unsupported = 1; |
| 4625 |
break; |
| 4626 |
default: |
| 4627 |
B43_WARN_ON(1); |
| 4628 |
} |
| 4629 |
if (unsupported) { |
| 4630 |
b43err(dev->wl, |
| 4631 |
"FOUND UNSUPPORTED RADIO (Manuf 0x%X, ID 0x%X, Revision %u, Version %u)\n", |
| 4632 |
radio_manuf, radio_id, radio_rev, radio_ver); |
| 4633 |
return -EOPNOTSUPP; |
| 4634 |
} |
| 4635 |
b43info(dev->wl, |
| 4636 |
"Found Radio: Manuf 0x%X, ID 0x%X, Revision %u, Version %u\n", |
| 4637 |
radio_manuf, radio_id, radio_rev, radio_ver); |
| 4638 |
|
| 4639 |
/* FIXME: b43 treats "id" as "ver" and ignores the real "ver" */ |
| 4640 |
phy->radio_manuf = radio_manuf; |
| 4641 |
phy->radio_ver = radio_id; |
| 4642 |
phy->radio_rev = radio_rev; |
| 4643 |
|
| 4644 |
phy->analog = analog_type; |
| 4645 |
phy->type = phy_type; |
| 4646 |
phy->rev = phy_rev; |
| 4647 |
|
| 4648 |
return 0; |
| 4649 |
} |
| 4650 |
|
| 4651 |
static void setup_struct_phy_for_init(struct b43_wldev *dev, |
| 4652 |
struct b43_phy *phy) |
| 4653 |
{ |
| 4654 |
phy->hardware_power_control = !!modparam_hwpctl; |
| 4655 |
phy->next_txpwr_check_time = jiffies; |
| 4656 |
/* PHY TX errors counter. */ |
| 4657 |
atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT); |
| 4658 |
|
| 4659 |
#if B43_DEBUG |
| 4660 |
phy->phy_locked = false; |
| 4661 |
phy->radio_locked = false; |
| 4662 |
#endif |
| 4663 |
} |
| 4664 |
|
| 4665 |
static void setup_struct_wldev_for_init(struct b43_wldev *dev) |
| 4666 |
{ |
| 4667 |
dev->dfq_valid = false; |
| 4668 |
|
| 4669 |
/* Assume the radio is enabled. If it's not enabled, the state will |
| 4670 |
* immediately get fixed on the first periodic work run. */ |
| 4671 |
dev->radio_hw_enable = true; |
| 4672 |
|
| 4673 |
/* Stats */ |
| 4674 |
memset(&dev->stats, 0, sizeof(dev->stats)); |
| 4675 |
|
| 4676 |
setup_struct_phy_for_init(dev, &dev->phy); |
| 4677 |
|
| 4678 |
/* IRQ related flags */ |
| 4679 |
dev->irq_reason = 0; |
| 4680 |
memset(dev->dma_reason, 0, sizeof(dev->dma_reason)); |
| 4681 |
dev->irq_mask = B43_IRQ_MASKTEMPLATE; |
| 4682 |
if (b43_modparam_verbose < B43_VERBOSITY_DEBUG) |
| 4683 |
dev->irq_mask &= ~B43_IRQ_PHY_TXERR; |
| 4684 |
|
| 4685 |
dev->mac_suspended = 1; |
| 4686 |
|
| 4687 |
/* Noise calculation context */ |
| 4688 |
memset(&dev->noisecalc, 0, sizeof(dev->noisecalc)); |
| 4689 |
} |
| 4690 |
|
| 4691 |
static void b43_bluetooth_coext_enable(struct b43_wldev *dev) |
| 4692 |
{ |
| 4693 |
struct ssb_sprom *sprom = dev->dev->bus_sprom; |
| 4694 |
u64 hf; |
| 4695 |
|
| 4696 |
if (!modparam_btcoex) |
| 4697 |
return; |
| 4698 |
if (!(sprom->boardflags_lo & B43_BFL_BTCOEXIST)) |
| 4699 |
return; |
| 4700 |
if (dev->phy.type != B43_PHYTYPE_B && !dev->phy.gmode) |
| 4701 |
return; |
| 4702 |
|
| 4703 |
hf = b43_hf_read(dev); |
| 4704 |
if (sprom->boardflags_lo & B43_BFL_BTCMOD) |
| 4705 |
hf |= B43_HF_BTCOEXALT; |
| 4706 |
else |
| 4707 |
hf |= B43_HF_BTCOEX; |
| 4708 |
b43_hf_write(dev, hf); |
| 4709 |
} |
| 4710 |
|
| 4711 |
static void b43_bluetooth_coext_disable(struct b43_wldev *dev) |
| 4712 |
{ |
| 4713 |
if (!modparam_btcoex) |
| 4714 |
return; |
| 4715 |
//TODO |
| 4716 |
} |
| 4717 |
|
| 4718 |
static void b43_imcfglo_timeouts_workaround(struct b43_wldev *dev) |
| 4719 |
{ |
| 4720 |
struct ssb_bus *bus; |
| 4721 |
u32 tmp; |
| 4722 |
|
| 4723 |
#ifdef CONFIG_B43_SSB |
| 4724 |
if (dev->dev->bus_type != B43_BUS_SSB) |
| 4725 |
return; |
| 4726 |
#else |
| 4727 |
return; |
| 4728 |
#endif |
| 4729 |
|
| 4730 |
bus = dev->dev->sdev->bus; |
| 4731 |
|
| 4732 |
if ((bus->chip_id == 0x4311 && bus->chip_rev == 2) || |
| 4733 |
(bus->chip_id == 0x4312)) { |
| 4734 |
tmp = ssb_read32(dev->dev->sdev, SSB_IMCFGLO); |
| 4735 |
tmp &= ~SSB_IMCFGLO_REQTO; |
| 4736 |
tmp &= ~SSB_IMCFGLO_SERTO; |
| 4737 |
tmp |= 0x3; |
| 4738 |
ssb_write32(dev->dev->sdev, SSB_IMCFGLO, tmp); |
| 4739 |
ssb_commit_settings(bus); |
| 4740 |
} |
| 4741 |
} |
| 4742 |
|
| 4743 |
static void b43_set_synth_pu_delay(struct b43_wldev *dev, bool idle) |
| 4744 |
{ |
| 4745 |
u16 pu_delay; |
| 4746 |
|
| 4747 |
/* The time value is in microseconds. */ |
| 4748 |
pu_delay = 1050; |
| 4749 |
if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC) || idle) |
| 4750 |
pu_delay = 500; |
| 4751 |
if ((dev->phy.radio_ver == 0x2050) && (dev->phy.radio_rev == 8)) |
| 4752 |
pu_delay = max(pu_delay, (u16)2400); |
| 4753 |
|
| 4754 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_SPUWKUP, pu_delay); |
| 4755 |
} |
| 4756 |
|
| 4757 |
/* Set the TSF CFP pre-TargetBeaconTransmissionTime. */ |
| 4758 |
static void b43_set_pretbtt(struct b43_wldev *dev) |
| 4759 |
{ |
| 4760 |
u16 pretbtt; |
| 4761 |
|
| 4762 |
/* The time value is in microseconds. */ |
| 4763 |
if (b43_is_mode(dev->wl, NL80211_IFTYPE_ADHOC)) |
| 4764 |
pretbtt = 2; |
| 4765 |
else |
| 4766 |
pretbtt = 250; |
| 4767 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRETBTT, pretbtt); |
| 4768 |
b43_write16(dev, B43_MMIO_TSF_CFP_PRETBTT, pretbtt); |
| 4769 |
} |
| 4770 |
|
| 4771 |
/* Shutdown a wireless core */ |
| 4772 |
/* Locking: wl->mutex */ |
| 4773 |
static void b43_wireless_core_exit(struct b43_wldev *dev) |
| 4774 |
{ |
| 4775 |
B43_WARN_ON(dev && b43_status(dev) > B43_STAT_INITIALIZED); |
| 4776 |
if (!dev || b43_status(dev) != B43_STAT_INITIALIZED) |
| 4777 |
return; |
| 4778 |
|
| 4779 |
b43_set_status(dev, B43_STAT_UNINIT); |
| 4780 |
|
| 4781 |
/* Stop the microcode PSM. */ |
| 4782 |
b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PSM_RUN, |
| 4783 |
B43_MACCTL_PSM_JMP0); |
| 4784 |
|
| 4785 |
switch (dev->dev->bus_type) { |
| 4786 |
#ifdef CONFIG_B43_BCMA |
| 4787 |
case B43_BUS_BCMA: |
| 4788 |
bcma_host_pci_down(dev->dev->bdev->bus); |
| 4789 |
break; |
| 4790 |
#endif |
| 4791 |
#ifdef CONFIG_B43_SSB |
| 4792 |
case B43_BUS_SSB: |
| 4793 |
/* TODO */ |
| 4794 |
break; |
| 4795 |
#endif |
| 4796 |
} |
| 4797 |
|
| 4798 |
b43_dma_free(dev); |
| 4799 |
b43_pio_free(dev); |
| 4800 |
b43_chip_exit(dev); |
| 4801 |
dev->phy.ops->switch_analog(dev, 0); |
| 4802 |
if (dev->wl->current_beacon) { |
| 4803 |
dev_kfree_skb_any(dev->wl->current_beacon); |
| 4804 |
dev->wl->current_beacon = NULL; |
| 4805 |
} |
| 4806 |
|
| 4807 |
b43_device_disable(dev, 0); |
| 4808 |
b43_bus_may_powerdown(dev); |
| 4809 |
} |
| 4810 |
|
| 4811 |
/* Initialize a wireless core */ |
| 4812 |
static int b43_wireless_core_init(struct b43_wldev *dev) |
| 4813 |
{ |
| 4814 |
struct ssb_sprom *sprom = dev->dev->bus_sprom; |
| 4815 |
struct b43_phy *phy = &dev->phy; |
| 4816 |
int err; |
| 4817 |
u64 hf; |
| 4818 |
|
| 4819 |
B43_WARN_ON(b43_status(dev) != B43_STAT_UNINIT); |
| 4820 |
|
| 4821 |
err = b43_bus_powerup(dev, 0); |
| 4822 |
if (err) |
| 4823 |
goto out; |
| 4824 |
if (!b43_device_is_enabled(dev)) |
| 4825 |
b43_wireless_core_reset(dev, phy->gmode); |
| 4826 |
|
| 4827 |
/* Reset all data structures. */ |
| 4828 |
setup_struct_wldev_for_init(dev); |
| 4829 |
phy->ops->prepare_structs(dev); |
| 4830 |
|
| 4831 |
/* Enable IRQ routing to this device. */ |
| 4832 |
switch (dev->dev->bus_type) { |
| 4833 |
#ifdef CONFIG_B43_BCMA |
| 4834 |
case B43_BUS_BCMA: |
| 4835 |
bcma_host_pci_irq_ctl(dev->dev->bdev->bus, |
| 4836 |
dev->dev->bdev, true); |
| 4837 |
bcma_host_pci_up(dev->dev->bdev->bus); |
| 4838 |
break; |
| 4839 |
#endif |
| 4840 |
#ifdef CONFIG_B43_SSB |
| 4841 |
case B43_BUS_SSB: |
| 4842 |
ssb_pcicore_dev_irqvecs_enable(&dev->dev->sdev->bus->pcicore, |
| 4843 |
dev->dev->sdev); |
| 4844 |
break; |
| 4845 |
#endif |
| 4846 |
} |
| 4847 |
|
| 4848 |
b43_imcfglo_timeouts_workaround(dev); |
| 4849 |
b43_bluetooth_coext_disable(dev); |
| 4850 |
if (phy->ops->prepare_hardware) { |
| 4851 |
err = phy->ops->prepare_hardware(dev); |
| 4852 |
if (err) |
| 4853 |
goto err_busdown; |
| 4854 |
} |
| 4855 |
err = b43_chip_init(dev); |
| 4856 |
if (err) |
| 4857 |
goto err_busdown; |
| 4858 |
b43_shm_write16(dev, B43_SHM_SHARED, |
| 4859 |
B43_SHM_SH_WLCOREREV, dev->dev->core_rev); |
| 4860 |
hf = b43_hf_read(dev); |
| 4861 |
if (phy->type == B43_PHYTYPE_G) { |
| 4862 |
hf |= B43_HF_SYMW; |
| 4863 |
if (phy->rev == 1) |
| 4864 |
hf |= B43_HF_GDCW; |
| 4865 |
if (sprom->boardflags_lo & B43_BFL_PACTRL) |
| 4866 |
hf |= B43_HF_OFDMPABOOST; |
| 4867 |
} |
| 4868 |
if (phy->radio_ver == 0x2050) { |
| 4869 |
if (phy->radio_rev == 6) |
| 4870 |
hf |= B43_HF_4318TSSI; |
| 4871 |
if (phy->radio_rev < 6) |
| 4872 |
hf |= B43_HF_VCORECALC; |
| 4873 |
} |
| 4874 |
if (sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW) |
| 4875 |
hf |= B43_HF_DSCRQ; /* Disable slowclock requests from ucode. */ |
| 4876 |
#if defined(CONFIG_B43_SSB) && defined(CONFIG_SSB_DRIVER_PCICORE) |
| 4877 |
if (dev->dev->bus_type == B43_BUS_SSB && |
| 4878 |
dev->dev->sdev->bus->bustype == SSB_BUSTYPE_PCI && |
| 4879 |
dev->dev->sdev->bus->pcicore.dev->id.revision <= 10) |
| 4880 |
hf |= B43_HF_PCISCW; /* PCI slow clock workaround. */ |
| 4881 |
#endif |
| 4882 |
hf &= ~B43_HF_SKCFPUP; |
| 4883 |
b43_hf_write(dev, hf); |
| 4884 |
|
| 4885 |
/* tell the ucode MAC capabilities */ |
| 4886 |
if (dev->dev->core_rev >= 13) { |
| 4887 |
u32 mac_hw_cap = b43_read32(dev, B43_MMIO_MAC_HW_CAP); |
| 4888 |
|
| 4889 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_MACHW_L, |
| 4890 |
mac_hw_cap & 0xffff); |
| 4891 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_MACHW_H, |
| 4892 |
(mac_hw_cap >> 16) & 0xffff); |
| 4893 |
} |
| 4894 |
|
| 4895 |
b43_set_retry_limits(dev, B43_DEFAULT_SHORT_RETRY_LIMIT, |
| 4896 |
B43_DEFAULT_LONG_RETRY_LIMIT); |
| 4897 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_SFFBLIM, 3); |
| 4898 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_LFFBLIM, 2); |
| 4899 |
|
| 4900 |
/* Disable sending probe responses from firmware. |
| 4901 |
* Setting the MaxTime to one usec will always trigger |
| 4902 |
* a timeout, so we never send any probe resp. |
| 4903 |
* A timeout of zero is infinite. */ |
| 4904 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PRMAXTIME, 1); |
| 4905 |
|
| 4906 |
b43_rate_memory_init(dev); |
| 4907 |
b43_set_phytxctl_defaults(dev); |
| 4908 |
|
| 4909 |
/* Minimum Contention Window */ |
| 4910 |
if (phy->type == B43_PHYTYPE_B) |
| 4911 |
b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MINCONT, 0x1F); |
| 4912 |
else |
| 4913 |
b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MINCONT, 0xF); |
| 4914 |
/* Maximum Contention Window */ |
| 4915 |
b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MAXCONT, 0x3FF); |
| 4916 |
|
| 4917 |
/* write phytype and phyvers */ |
| 4918 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PHYTYPE, phy->type); |
| 4919 |
b43_shm_write16(dev, B43_SHM_SHARED, B43_SHM_SH_PHYVER, phy->rev); |
| 4920 |
|
| 4921 |
if (b43_bus_host_is_pcmcia(dev->dev) || |
| 4922 |
b43_bus_host_is_sdio(dev->dev)) { |
| 4923 |
dev->__using_pio_transfers = true; |
| 4924 |
err = b43_pio_init(dev); |
| 4925 |
} else if (dev->use_pio) { |
| 4926 |
b43warn(dev->wl, "Forced PIO by use_pio module parameter. " |
| 4927 |
"This should not be needed and will result in lower " |
| 4928 |
"performance.\n"); |
| 4929 |
dev->__using_pio_transfers = true; |
| 4930 |
err = b43_pio_init(dev); |
| 4931 |
} else { |
| 4932 |
dev->__using_pio_transfers = false; |
| 4933 |
err = b43_dma_init(dev); |
| 4934 |
} |
| 4935 |
if (err) |
| 4936 |
goto err_chip_exit; |
| 4937 |
b43_qos_init(dev); |
| 4938 |
b43_set_synth_pu_delay(dev, 1); |
| 4939 |
b43_bluetooth_coext_enable(dev); |
| 4940 |
|
| 4941 |
b43_bus_powerup(dev, !(sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW)); |
| 4942 |
b43_upload_card_macaddress(dev); |
| 4943 |
b43_security_init(dev); |
| 4944 |
|
| 4945 |
ieee80211_wake_queues(dev->wl->hw); |
| 4946 |
|
| 4947 |
b43_set_status(dev, B43_STAT_INITIALIZED); |
| 4948 |
|
| 4949 |
out: |
| 4950 |
return err; |
| 4951 |
|
| 4952 |
err_chip_exit: |
| 4953 |
b43_chip_exit(dev); |
| 4954 |
err_busdown: |
| 4955 |
b43_bus_may_powerdown(dev); |
| 4956 |
B43_WARN_ON(b43_status(dev) != B43_STAT_UNINIT); |
| 4957 |
return err; |
| 4958 |
} |
| 4959 |
|
| 4960 |
static int b43_op_add_interface(struct ieee80211_hw *hw, |
| 4961 |
struct ieee80211_vif *vif) |
| 4962 |
{ |
| 4963 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 4964 |
struct b43_wldev *dev; |
| 4965 |
int err = -EOPNOTSUPP; |
| 4966 |
|
| 4967 |
/* TODO: allow AP devices to coexist */ |
| 4968 |
|
| 4969 |
if (vif->type != NL80211_IFTYPE_AP && |
| 4970 |
vif->type != NL80211_IFTYPE_MESH_POINT && |
| 4971 |
vif->type != NL80211_IFTYPE_STATION && |
| 4972 |
vif->type != NL80211_IFTYPE_ADHOC) |
| 4973 |
return -EOPNOTSUPP; |
| 4974 |
|
| 4975 |
mutex_lock(&wl->mutex); |
| 4976 |
if (wl->operating) |
| 4977 |
goto out_mutex_unlock; |
| 4978 |
|
| 4979 |
b43dbg(wl, "Adding Interface type %d\n", vif->type); |
| 4980 |
|
| 4981 |
dev = wl->current_dev; |
| 4982 |
wl->operating = true; |
| 4983 |
wl->vif = vif; |
| 4984 |
wl->if_type = vif->type; |
| 4985 |
memcpy(wl->mac_addr, vif->addr, ETH_ALEN); |
| 4986 |
|
| 4987 |
b43_adjust_opmode(dev); |
| 4988 |
b43_set_pretbtt(dev); |
| 4989 |
b43_set_synth_pu_delay(dev, 0); |
| 4990 |
b43_upload_card_macaddress(dev); |
| 4991 |
|
| 4992 |
err = 0; |
| 4993 |
out_mutex_unlock: |
| 4994 |
mutex_unlock(&wl->mutex); |
| 4995 |
|
| 4996 |
if (err == 0) |
| 4997 |
b43_op_bss_info_changed(hw, vif, &vif->bss_conf, ~0); |
| 4998 |
|
| 4999 |
return err; |
| 5000 |
} |
| 5001 |
|
| 5002 |
static void b43_op_remove_interface(struct ieee80211_hw *hw, |
| 5003 |
struct ieee80211_vif *vif) |
| 5004 |
{ |
| 5005 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 5006 |
struct b43_wldev *dev = wl->current_dev; |
| 5007 |
|
| 5008 |
b43dbg(wl, "Removing Interface type %d\n", vif->type); |
| 5009 |
|
| 5010 |
mutex_lock(&wl->mutex); |
| 5011 |
|
| 5012 |
B43_WARN_ON(!wl->operating); |
| 5013 |
B43_WARN_ON(wl->vif != vif); |
| 5014 |
wl->vif = NULL; |
| 5015 |
|
| 5016 |
wl->operating = false; |
| 5017 |
|
| 5018 |
b43_adjust_opmode(dev); |
| 5019 |
eth_zero_addr(wl->mac_addr); |
| 5020 |
b43_upload_card_macaddress(dev); |
| 5021 |
|
| 5022 |
mutex_unlock(&wl->mutex); |
| 5023 |
} |
| 5024 |
|
| 5025 |
static int b43_op_start(struct ieee80211_hw *hw) |
| 5026 |
{ |
| 5027 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 5028 |
struct b43_wldev *dev = wl->current_dev; |
| 5029 |
int did_init = 0; |
| 5030 |
int err = 0; |
| 5031 |
|
| 5032 |
/* Kill all old instance specific information to make sure |
| 5033 |
* the card won't use it in the short timeframe between start |
| 5034 |
* and mac80211 reconfiguring it. */ |
| 5035 |
eth_zero_addr(wl->bssid); |
| 5036 |
eth_zero_addr(wl->mac_addr); |
| 5037 |
wl->filter_flags = 0; |
| 5038 |
wl->radiotap_enabled = false; |
| 5039 |
b43_qos_clear(wl); |
| 5040 |
wl->beacon0_uploaded = false; |
| 5041 |
wl->beacon1_uploaded = false; |
| 5042 |
wl->beacon_templates_virgin = true; |
| 5043 |
wl->radio_enabled = true; |
| 5044 |
|
| 5045 |
mutex_lock(&wl->mutex); |
| 5046 |
|
| 5047 |
if (b43_status(dev) < B43_STAT_INITIALIZED) { |
| 5048 |
err = b43_wireless_core_init(dev); |
| 5049 |
if (err) |
| 5050 |
goto out_mutex_unlock; |
| 5051 |
did_init = 1; |
| 5052 |
} |
| 5053 |
|
| 5054 |
if (b43_status(dev) < B43_STAT_STARTED) { |
| 5055 |
err = b43_wireless_core_start(dev); |
| 5056 |
if (err) { |
| 5057 |
if (did_init) |
| 5058 |
b43_wireless_core_exit(dev); |
| 5059 |
goto out_mutex_unlock; |
| 5060 |
} |
| 5061 |
} |
| 5062 |
|
| 5063 |
/* XXX: only do if device doesn't support rfkill irq */ |
| 5064 |
wiphy_rfkill_start_polling(hw->wiphy); |
| 5065 |
|
| 5066 |
out_mutex_unlock: |
| 5067 |
mutex_unlock(&wl->mutex); |
| 5068 |
|
| 5069 |
/* |
| 5070 |
* Configuration may have been overwritten during initialization. |
| 5071 |
* Reload the configuration, but only if initialization was |
| 5072 |
* successful. Reloading the configuration after a failed init |
| 5073 |
* may hang the system. |
| 5074 |
*/ |
| 5075 |
if (!err) |
| 5076 |
b43_op_config(hw, -1, ~0); |
| 5077 |
|
| 5078 |
return err; |
| 5079 |
} |
| 5080 |
|
| 5081 |
static void b43_op_stop(struct ieee80211_hw *hw, bool suspend) |
| 5082 |
{ |
| 5083 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 5084 |
struct b43_wldev *dev = wl->current_dev; |
| 5085 |
|
| 5086 |
cancel_work_sync(&(wl->beacon_update_trigger)); |
| 5087 |
|
| 5088 |
if (!dev) |
| 5089 |
goto out; |
| 5090 |
|
| 5091 |
mutex_lock(&wl->mutex); |
| 5092 |
if (b43_status(dev) >= B43_STAT_STARTED) { |
| 5093 |
dev = b43_wireless_core_stop(dev); |
| 5094 |
if (!dev) |
| 5095 |
goto out_unlock; |
| 5096 |
} |
| 5097 |
b43_wireless_core_exit(dev); |
| 5098 |
wl->radio_enabled = false; |
| 5099 |
|
| 5100 |
out_unlock: |
| 5101 |
mutex_unlock(&wl->mutex); |
| 5102 |
out: |
| 5103 |
cancel_work_sync(&(wl->txpower_adjust_work)); |
| 5104 |
} |
| 5105 |
|
| 5106 |
static int b43_op_beacon_set_tim(struct ieee80211_hw *hw, |
| 5107 |
struct ieee80211_sta *sta, bool set) |
| 5108 |
{ |
| 5109 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 5110 |
|
| 5111 |
b43_update_templates(wl); |
| 5112 |
|
| 5113 |
return 0; |
| 5114 |
} |
| 5115 |
|
| 5116 |
static void b43_op_sta_notify(struct ieee80211_hw *hw, |
| 5117 |
struct ieee80211_vif *vif, |
| 5118 |
enum sta_notify_cmd notify_cmd, |
| 5119 |
struct ieee80211_sta *sta) |
| 5120 |
{ |
| 5121 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 5122 |
|
| 5123 |
B43_WARN_ON(!vif || wl->vif != vif); |
| 5124 |
} |
| 5125 |
|
| 5126 |
static void b43_op_sw_scan_start_notifier(struct ieee80211_hw *hw, |
| 5127 |
struct ieee80211_vif *vif, |
| 5128 |
const u8 *mac_addr) |
| 5129 |
{ |
| 5130 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 5131 |
struct b43_wldev *dev; |
| 5132 |
|
| 5133 |
mutex_lock(&wl->mutex); |
| 5134 |
dev = wl->current_dev; |
| 5135 |
if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) { |
| 5136 |
/* Disable CFP update during scan on other channels. */ |
| 5137 |
b43_hf_write(dev, b43_hf_read(dev) | B43_HF_SKCFPUP); |
| 5138 |
} |
| 5139 |
mutex_unlock(&wl->mutex); |
| 5140 |
} |
| 5141 |
|
| 5142 |
static void b43_op_sw_scan_complete_notifier(struct ieee80211_hw *hw, |
| 5143 |
struct ieee80211_vif *vif) |
| 5144 |
{ |
| 5145 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 5146 |
struct b43_wldev *dev; |
| 5147 |
|
| 5148 |
mutex_lock(&wl->mutex); |
| 5149 |
dev = wl->current_dev; |
| 5150 |
if (dev && (b43_status(dev) >= B43_STAT_INITIALIZED)) { |
| 5151 |
/* Re-enable CFP update. */ |
| 5152 |
b43_hf_write(dev, b43_hf_read(dev) & ~B43_HF_SKCFPUP); |
| 5153 |
} |
| 5154 |
mutex_unlock(&wl->mutex); |
| 5155 |
} |
| 5156 |
|
| 5157 |
static int b43_op_get_survey(struct ieee80211_hw *hw, int idx, |
| 5158 |
struct survey_info *survey) |
| 5159 |
{ |
| 5160 |
struct b43_wl *wl = hw_to_b43_wl(hw); |
| 5161 |
struct b43_wldev *dev = wl->current_dev; |
| 5162 |
struct ieee80211_conf *conf = &hw->conf; |
| 5163 |
|
| 5164 |
if (idx != 0) |
| 5165 |
return -ENOENT; |
| 5166 |
|
| 5167 |
survey->channel = conf->chandef.chan; |
| 5168 |
survey->filled = SURVEY_INFO_NOISE_DBM; |
| 5169 |
survey->noise = dev->stats.link_noise; |
| 5170 |
|
| 5171 |
return 0; |
| 5172 |
} |
| 5173 |
|
| 5174 |
static const struct ieee80211_ops b43_hw_ops = { |
| 5175 |
.add_chanctx = ieee80211_emulate_add_chanctx, |
| 5176 |
.remove_chanctx = ieee80211_emulate_remove_chanctx, |
| 5177 |
.change_chanctx = ieee80211_emulate_change_chanctx, |
| 5178 |
.switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx, |
| 5179 |
.tx = b43_op_tx, |
| 5180 |
.wake_tx_queue = ieee80211_handle_wake_tx_queue, |
| 5181 |
.conf_tx = b43_op_conf_tx, |
| 5182 |
.add_interface = b43_op_add_interface, |
| 5183 |
.remove_interface = b43_op_remove_interface, |
| 5184 |
.config = b43_op_config, |
| 5185 |
.bss_info_changed = b43_op_bss_info_changed, |
| 5186 |
.configure_filter = b43_op_configure_filter, |
| 5187 |
.set_key = b43_op_set_key, |
| 5188 |
.update_tkip_key = b43_op_update_tkip_key, |
| 5189 |
.get_stats = b43_op_get_stats, |
| 5190 |
.get_tsf = b43_op_get_tsf, |
| 5191 |
.set_tsf = b43_op_set_tsf, |
| 5192 |
.start = b43_op_start, |
| 5193 |
.stop = b43_op_stop, |
| 5194 |
.set_tim = b43_op_beacon_set_tim, |
| 5195 |
.sta_notify = b43_op_sta_notify, |
| 5196 |
.sw_scan_start = b43_op_sw_scan_start_notifier, |
| 5197 |
.sw_scan_complete = b43_op_sw_scan_complete_notifier, |
| 5198 |
.get_survey = b43_op_get_survey, |
| 5199 |
.rfkill_poll = b43_rfkill_poll, |
| 5200 |
}; |
| 5201 |
|
| 5202 |
/* Hard-reset the chip. Do not call this directly. |
| 5203 |
* Use b43_controller_restart() |
| 5204 |
*/ |
| 5205 |
static void b43_chip_reset(struct work_struct *work) |
| 5206 |
{ |
| 5207 |
struct b43_wldev *dev = |
| 5208 |
container_of(work, struct b43_wldev, restart_work); |
| 5209 |
struct b43_wl *wl = dev->wl; |
| 5210 |
int err = 0; |
| 5211 |
int prev_status; |
| 5212 |
|
| 5213 |
mutex_lock(&wl->mutex); |
| 5214 |
|
| 5215 |
prev_status = b43_status(dev); |
| 5216 |
/* Bring the device down... */ |
| 5217 |
if (prev_status >= B43_STAT_STARTED) { |
| 5218 |
dev = b43_wireless_core_stop(dev); |
| 5219 |
if (!dev) { |
| 5220 |
err = -ENODEV; |
| 5221 |
goto out; |
| 5222 |
} |
| 5223 |
} |
| 5224 |
if (prev_status >= B43_STAT_INITIALIZED) |
| 5225 |
b43_wireless_core_exit(dev); |
| 5226 |
|
| 5227 |
/* ...and up again. */ |
| 5228 |
if (prev_status >= B43_STAT_INITIALIZED) { |
| 5229 |
err = b43_wireless_core_init(dev); |
| 5230 |
if (err) |
| 5231 |
goto out; |
| 5232 |
} |
| 5233 |
if (prev_status >= B43_STAT_STARTED) { |
| 5234 |
err = b43_wireless_core_start(dev); |
| 5235 |
if (err) { |
| 5236 |
b43_wireless_core_exit(dev); |
| 5237 |
goto out; |
| 5238 |
} |
| 5239 |
} |
| 5240 |
out: |
| 5241 |
if (err) |
| 5242 |
wl->current_dev = NULL; /* Failed to init the dev. */ |
| 5243 |
mutex_unlock(&wl->mutex); |
| 5244 |
|
| 5245 |
if (err) { |
| 5246 |
b43err(wl, "Controller restart FAILED\n"); |
| 5247 |
return; |
| 5248 |
} |
| 5249 |
|
| 5250 |
/* reload configuration */ |
| 5251 |
b43_op_config(wl->hw, -1, ~0); |
| 5252 |
if (wl->vif) |
| 5253 |
b43_op_bss_info_changed(wl->hw, wl->vif, &wl->vif->bss_conf, ~0); |
| 5254 |
|
| 5255 |
b43info(wl, "Controller restarted\n"); |
| 5256 |
} |
| 5257 |
|
| 5258 |
static int b43_setup_bands(struct b43_wldev *dev, |
| 5259 |
bool have_2ghz_phy, bool have_5ghz_phy) |
| 5260 |
{ |
| 5261 |
struct ieee80211_hw *hw = dev->wl->hw; |
| 5262 |
struct b43_phy *phy = &dev->phy; |
| 5263 |
bool limited_2g; |
| 5264 |
bool limited_5g; |
| 5265 |
|
| 5266 |
/* We don't support all 2 GHz channels on some devices */ |
| 5267 |
limited_2g = phy->radio_ver == 0x2057 && |
| 5268 |
(phy->radio_rev == 9 || phy->radio_rev == 14); |
| 5269 |
limited_5g = phy->radio_ver == 0x2057 && |
| 5270 |
phy->radio_rev == 9; |
| 5271 |
|
| 5272 |
if (have_2ghz_phy) |
| 5273 |
hw->wiphy->bands[NL80211_BAND_2GHZ] = limited_2g ? |
| 5274 |
&b43_band_2ghz_limited : &b43_band_2GHz; |
| 5275 |
if (dev->phy.type == B43_PHYTYPE_N) { |
| 5276 |
if (have_5ghz_phy) |
| 5277 |
hw->wiphy->bands[NL80211_BAND_5GHZ] = limited_5g ? |
| 5278 |
&b43_band_5GHz_nphy_limited : |
| 5279 |
&b43_band_5GHz_nphy; |
| 5280 |
} else { |
| 5281 |
if (have_5ghz_phy) |
| 5282 |
hw->wiphy->bands[NL80211_BAND_5GHZ] = &b43_band_5GHz_aphy; |
| 5283 |
} |
| 5284 |
|
| 5285 |
dev->phy.supports_2ghz = have_2ghz_phy; |
| 5286 |
dev->phy.supports_5ghz = have_5ghz_phy; |
| 5287 |
|
| 5288 |
return 0; |
| 5289 |
} |
| 5290 |
|
| 5291 |
static void b43_wireless_core_detach(struct b43_wldev *dev) |
| 5292 |
{ |
| 5293 |
/* We release firmware that late to not be required to re-request |
| 5294 |
* is all the time when we reinit the core. */ |
| 5295 |
b43_release_firmware(dev); |
| 5296 |
b43_phy_free(dev); |
| 5297 |
} |
| 5298 |
|
| 5299 |
static void b43_supported_bands(struct b43_wldev *dev, bool *have_2ghz_phy, |
| 5300 |
bool *have_5ghz_phy) |
| 5301 |
{ |
| 5302 |
u16 dev_id = 0; |
| 5303 |
|
| 5304 |
#ifdef CONFIG_B43_BCMA |
| 5305 |
if (dev->dev->bus_type == B43_BUS_BCMA && |
| 5306 |
dev->dev->bdev->bus->hosttype == BCMA_HOSTTYPE_PCI) |
| 5307 |
dev_id = dev->dev->bdev->bus->host_pci->device; |
| 5308 |
#endif |
| 5309 |
#ifdef CONFIG_B43_SSB |
| 5310 |
if (dev->dev->bus_type == B43_BUS_SSB && |
| 5311 |
dev->dev->sdev->bus->bustype == SSB_BUSTYPE_PCI) |
| 5312 |
dev_id = dev->dev->sdev->bus->host_pci->device; |
| 5313 |
#endif |
| 5314 |
/* Override with SPROM value if available */ |
| 5315 |
if (dev->dev->bus_sprom->dev_id) |
| 5316 |
dev_id = dev->dev->bus_sprom->dev_id; |
| 5317 |
|
| 5318 |
/* Note: below IDs can be "virtual" (not maching e.g. real PCI ID) */ |
| 5319 |
switch (dev_id) { |
| 5320 |
case 0x4324: /* BCM4306 */ |
| 5321 |
case 0x4312: /* BCM4311 */ |
| 5322 |
case 0x4319: /* BCM4318 */ |
| 5323 |
case 0x4328: /* BCM4321 */ |
| 5324 |
case 0x432b: /* BCM4322 */ |
| 5325 |
case 0x4350: /* BCM43222 */ |
| 5326 |
case 0x4353: /* BCM43224 */ |
| 5327 |
case 0x0576: /* BCM43224 */ |
| 5328 |
case 0x435f: /* BCM6362 */ |
| 5329 |
case 0x4331: /* BCM4331 */ |
| 5330 |
case 0x4359: /* BCM43228 */ |
| 5331 |
case 0x43a0: /* BCM4360 */ |
| 5332 |
case 0x43b1: /* BCM4352 */ |
| 5333 |
/* Dual band devices */ |
| 5334 |
*have_2ghz_phy = true; |
| 5335 |
*have_5ghz_phy = true; |
| 5336 |
return; |
| 5337 |
case 0x4321: /* BCM4306 */ |
| 5338 |
/* There are 14e4:4321 PCI devs with 2.4 GHz BCM4321 (N-PHY) */ |
| 5339 |
if (dev->phy.type != B43_PHYTYPE_G) |
| 5340 |
break; |
| 5341 |
fallthrough; |
| 5342 |
case 0x4313: /* BCM4311 */ |
| 5343 |
case 0x431a: /* BCM4318 */ |
| 5344 |
case 0x432a: /* BCM4321 */ |
| 5345 |
case 0x432d: /* BCM4322 */ |
| 5346 |
case 0x4352: /* BCM43222 */ |
| 5347 |
case 0x435a: /* BCM43228 */ |
| 5348 |
case 0x4333: /* BCM4331 */ |
| 5349 |
case 0x43a2: /* BCM4360 */ |
| 5350 |
case 0x43b3: /* BCM4352 */ |
| 5351 |
/* 5 GHz only devices */ |
| 5352 |
*have_2ghz_phy = false; |
| 5353 |
*have_5ghz_phy = true; |
| 5354 |
return; |
| 5355 |
} |
| 5356 |
|
| 5357 |
/* As a fallback, try to guess using PHY type */ |
| 5358 |
switch (dev->phy.type) { |
| 5359 |
case B43_PHYTYPE_G: |
| 5360 |
case B43_PHYTYPE_N: |
| 5361 |
case B43_PHYTYPE_LP: |
| 5362 |
case B43_PHYTYPE_HT: |
| 5363 |
case B43_PHYTYPE_LCN: |
| 5364 |
*have_2ghz_phy = true; |
| 5365 |
*have_5ghz_phy = false; |
| 5366 |
return; |
| 5367 |
} |
| 5368 |
|
| 5369 |
B43_WARN_ON(1); |
| 5370 |
} |
| 5371 |
|
| 5372 |
static int b43_wireless_core_attach(struct b43_wldev *dev) |
| 5373 |
{ |
| 5374 |
struct b43_wl *wl = dev->wl; |
| 5375 |
struct b43_phy *phy = &dev->phy; |
| 5376 |
int err; |
| 5377 |
u32 tmp; |
| 5378 |
bool have_2ghz_phy = false, have_5ghz_phy = false; |
| 5379 |
|
| 5380 |
/* Do NOT do any device initialization here. |
| 5381 |
* Do it in wireless_core_init() instead. |
| 5382 |
* This function is for gathering basic information about the HW, only. |
| 5383 |
* Also some structs may be set up here. But most likely you want to have |
| 5384 |
* that in core_init(), too. |
| 5385 |
*/ |
| 5386 |
|
| 5387 |
err = b43_bus_powerup(dev, 0); |
| 5388 |
if (err) { |
| 5389 |
b43err(wl, "Bus powerup failed\n"); |
| 5390 |
goto out; |
| 5391 |
} |
| 5392 |
|
| 5393 |
phy->do_full_init = true; |
| 5394 |
|
| 5395 |
/* Try to guess supported bands for the first init needs */ |
| 5396 |
switch (dev->dev->bus_type) { |
| 5397 |
#ifdef CONFIG_B43_BCMA |
| 5398 |
case B43_BUS_BCMA: |
| 5399 |
tmp = bcma_aread32(dev->dev->bdev, BCMA_IOST); |
| 5400 |
have_2ghz_phy = !!(tmp & B43_BCMA_IOST_2G_PHY); |
| 5401 |
have_5ghz_phy = !!(tmp & B43_BCMA_IOST_5G_PHY); |
| 5402 |
break; |
| 5403 |
#endif |
| 5404 |
#ifdef CONFIG_B43_SSB |
| 5405 |
case B43_BUS_SSB: |
| 5406 |
if (dev->dev->core_rev >= 5) { |
| 5407 |
tmp = ssb_read32(dev->dev->sdev, SSB_TMSHIGH); |
| 5408 |
have_2ghz_phy = !!(tmp & B43_TMSHIGH_HAVE_2GHZ_PHY); |
| 5409 |
have_5ghz_phy = !!(tmp & B43_TMSHIGH_HAVE_5GHZ_PHY); |
| 5410 |
} else |
| 5411 |
B43_WARN_ON(1); |
| 5412 |
break; |
| 5413 |
#endif |
| 5414 |
} |
| 5415 |
|
| 5416 |
dev->phy.gmode = have_2ghz_phy; |
| 5417 |
b43_wireless_core_reset(dev, dev->phy.gmode); |
| 5418 |
|
| 5419 |
/* Get the PHY type. */ |
| 5420 |
err = b43_phy_versioning(dev); |
| 5421 |
if (err) |
| 5422 |
goto err_powerdown; |
| 5423 |
|
| 5424 |
/* Get real info about supported bands */ |
| 5425 |
b43_supported_bands(dev, &have_2ghz_phy, &have_5ghz_phy); |
| 5426 |
|
| 5427 |
/* We don't support 5 GHz on some PHYs yet */ |
| 5428 |
if (have_5ghz_phy) { |
| 5429 |
switch (dev->phy.type) { |
| 5430 |
case B43_PHYTYPE_G: |
| 5431 |
case B43_PHYTYPE_LP: |
| 5432 |
case B43_PHYTYPE_HT: |
| 5433 |
b43warn(wl, "5 GHz band is unsupported on this PHY\n"); |
| 5434 |
have_5ghz_phy = false; |
| 5435 |
} |
| 5436 |
} |
| 5437 |
|
| 5438 |
if (!have_2ghz_phy && !have_5ghz_phy) { |
| 5439 |
b43err(wl, "b43 can't support any band on this device\n"); |
| 5440 |
err = -EOPNOTSUPP; |
| 5441 |
goto err_powerdown; |
| 5442 |
} |
| 5443 |
|
| 5444 |
err = b43_phy_allocate(dev); |
| 5445 |
if (err) |
| 5446 |
goto err_powerdown; |
| 5447 |
|
| 5448 |
dev->phy.gmode = have_2ghz_phy; |
| 5449 |
b43_wireless_core_reset(dev, dev->phy.gmode); |
| 5450 |
|
| 5451 |
err = b43_validate_chipaccess(dev); |
| 5452 |
if (err) |
| 5453 |
goto err_phy_free; |
| 5454 |
err = b43_setup_bands(dev, have_2ghz_phy, have_5ghz_phy); |
| 5455 |
if (err) |
| 5456 |
goto err_phy_free; |
| 5457 |
|
| 5458 |
/* Now set some default "current_dev" */ |
| 5459 |
if (!wl->current_dev) |
| 5460 |
wl->current_dev = dev; |
| 5461 |
INIT_WORK(&dev->restart_work, b43_chip_reset); |
| 5462 |
|
| 5463 |
dev->phy.ops->switch_analog(dev, 0); |
| 5464 |
b43_device_disable(dev, 0); |
| 5465 |
b43_bus_may_powerdown(dev); |
| 5466 |
|
| 5467 |
out: |
| 5468 |
return err; |
| 5469 |
|
| 5470 |
err_phy_free: |
| 5471 |
b43_phy_free(dev); |
| 5472 |
err_powerdown: |
| 5473 |
b43_bus_may_powerdown(dev); |
| 5474 |
return err; |
| 5475 |
} |
| 5476 |
|
| 5477 |
static void b43_one_core_detach(struct b43_bus_dev *dev) |
| 5478 |
{ |
| 5479 |
struct b43_wldev *wldev; |
| 5480 |
|
| 5481 |
/* Do not cancel ieee80211-workqueue based work here. |
| 5482 |
* See comment in b43_remove(). */ |
| 5483 |
|
| 5484 |
wldev = b43_bus_get_wldev(dev); |
| 5485 |
b43_debugfs_remove_device(wldev); |
| 5486 |
b43_wireless_core_detach(wldev); |
| 5487 |
list_del(&wldev->list); |
| 5488 |
b43_bus_set_wldev(dev, NULL); |
| 5489 |
kfree(wldev); |
| 5490 |
} |
| 5491 |
|
| 5492 |
static int b43_one_core_attach(struct b43_bus_dev *dev, struct b43_wl *wl) |
| 5493 |
{ |
| 5494 |
struct b43_wldev *wldev; |
| 5495 |
int err = -ENOMEM; |
| 5496 |
|
| 5497 |
wldev = kzalloc_obj(*wldev); |
| 5498 |
if (!wldev) |
| 5499 |
goto out; |
| 5500 |
|
| 5501 |
wldev->use_pio = b43_modparam_pio; |
| 5502 |
wldev->dev = dev; |
| 5503 |
wldev->wl = wl; |
| 5504 |
b43_set_status(wldev, B43_STAT_UNINIT); |
| 5505 |
wldev->bad_frames_preempt = modparam_bad_frames_preempt; |
| 5506 |
INIT_LIST_HEAD(&wldev->list); |
| 5507 |
|
| 5508 |
err = b43_wireless_core_attach(wldev); |
| 5509 |
if (err) |
| 5510 |
goto err_kfree_wldev; |
| 5511 |
|
| 5512 |
b43_bus_set_wldev(dev, wldev); |
| 5513 |
b43_debugfs_add_device(wldev); |
| 5514 |
|
| 5515 |
out: |
| 5516 |
return err; |
| 5517 |
|
| 5518 |
err_kfree_wldev: |
| 5519 |
kfree(wldev); |
| 5520 |
return err; |
| 5521 |
} |
| 5522 |
|
| 5523 |
#define IS_PDEV(pdev, _vendor, _device, _subvendor, _subdevice) ( \ |
| 5524 |
(pdev->vendor == PCI_VENDOR_ID_##_vendor) && \ |
| 5525 |
(pdev->device == _device) && \ |
| 5526 |
(pdev->subsystem_vendor == PCI_VENDOR_ID_##_subvendor) && \ |
| 5527 |
(pdev->subsystem_device == _subdevice) ) |
| 5528 |
|
| 5529 |
#ifdef CONFIG_B43_SSB |
| 5530 |
static void b43_sprom_fixup(struct ssb_bus *bus) |
| 5531 |
{ |
| 5532 |
struct pci_dev *pdev; |
| 5533 |
|
| 5534 |
/* boardflags workarounds */ |
| 5535 |
if (bus->boardinfo.vendor == SSB_BOARDVENDOR_DELL && |
| 5536 |
bus->chip_id == 0x4301 && bus->sprom.board_rev == 0x74) |
| 5537 |
bus->sprom.boardflags_lo |= B43_BFL_BTCOEXIST; |
| 5538 |
if (bus->boardinfo.vendor == PCI_VENDOR_ID_APPLE && |
| 5539 |
bus->boardinfo.type == 0x4E && bus->sprom.board_rev > 0x40) |
| 5540 |
bus->sprom.boardflags_lo |= B43_BFL_PACTRL; |
| 5541 |
if (bus->bustype == SSB_BUSTYPE_PCI) { |
| 5542 |
pdev = bus->host_pci; |
| 5543 |
if (IS_PDEV(pdev, BROADCOM, 0x4318, ASUSTEK, 0x100F) || |
| 5544 |
IS_PDEV(pdev, BROADCOM, 0x4320, DELL, 0x0003) || |
| 5545 |
IS_PDEV(pdev, BROADCOM, 0x4320, HP, 0x12f8) || |
| 5546 |
IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0015) || |
| 5547 |
IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0014) || |
| 5548 |
IS_PDEV(pdev, BROADCOM, 0x4320, LINKSYS, 0x0013) || |
| 5549 |
IS_PDEV(pdev, BROADCOM, 0x4320, MOTOROLA, 0x7010)) |
| 5550 |
bus->sprom.boardflags_lo &= ~B43_BFL_BTCOEXIST; |
| 5551 |
} |
| 5552 |
} |
| 5553 |
|
| 5554 |
static void b43_wireless_exit(struct b43_bus_dev *dev, struct b43_wl *wl) |
| 5555 |
{ |
| 5556 |
struct ieee80211_hw *hw = wl->hw; |
| 5557 |
|
| 5558 |
ssb_set_devtypedata(dev->sdev, NULL); |
| 5559 |
ieee80211_free_hw(hw); |
| 5560 |
} |
| 5561 |
#endif |
| 5562 |
|
| 5563 |
static struct b43_wl *b43_wireless_init(struct b43_bus_dev *dev) |
| 5564 |
{ |
| 5565 |
struct ssb_sprom *sprom = dev->bus_sprom; |
| 5566 |
struct ieee80211_hw *hw; |
| 5567 |
struct b43_wl *wl; |
| 5568 |
char chip_name[6]; |
| 5569 |
int queue_num; |
| 5570 |
|
| 5571 |
hw = ieee80211_alloc_hw(sizeof(*wl), &b43_hw_ops); |
| 5572 |
if (!hw) { |
| 5573 |
b43err(NULL, "Could not allocate ieee80211 device\n"); |
| 5574 |
return ERR_PTR(-ENOMEM); |
| 5575 |
} |
| 5576 |
wl = hw_to_b43_wl(hw); |
| 5577 |
|
| 5578 |
/* fill hw info */ |
| 5579 |
ieee80211_hw_set(hw, RX_INCLUDES_FCS); |
| 5580 |
ieee80211_hw_set(hw, SIGNAL_DBM); |
| 5581 |
ieee80211_hw_set(hw, MFP_CAPABLE); |
| 5582 |
hw->wiphy->interface_modes = |
| 5583 |
BIT(NL80211_IFTYPE_AP) | |
| 5584 |
BIT(NL80211_IFTYPE_MESH_POINT) | |
| 5585 |
BIT(NL80211_IFTYPE_STATION) | |
| 5586 |
BIT(NL80211_IFTYPE_ADHOC); |
| 5587 |
|
| 5588 |
hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN; |
| 5589 |
|
| 5590 |
wiphy_ext_feature_set(hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); |
| 5591 |
|
| 5592 |
wl->hw_registered = false; |
| 5593 |
hw->max_rates = 2; |
| 5594 |
SET_IEEE80211_DEV(hw, dev->dev); |
| 5595 |
if (is_valid_ether_addr(sprom->et1mac)) |
| 5596 |
SET_IEEE80211_PERM_ADDR(hw, sprom->et1mac); |
| 5597 |
else |
| 5598 |
SET_IEEE80211_PERM_ADDR(hw, sprom->il0mac); |
| 5599 |
|
| 5600 |
/* Initialize struct b43_wl */ |
| 5601 |
wl->hw = hw; |
| 5602 |
mutex_init(&wl->mutex); |
| 5603 |
spin_lock_init(&wl->hardirq_lock); |
| 5604 |
spin_lock_init(&wl->beacon_lock); |
| 5605 |
INIT_WORK(&wl->beacon_update_trigger, b43_beacon_update_trigger_work); |
| 5606 |
INIT_WORK(&wl->txpower_adjust_work, b43_phy_txpower_adjust_work); |
| 5607 |
INIT_WORK(&wl->tx_work, b43_tx_work); |
| 5608 |
|
| 5609 |
/* Initialize queues and flags. */ |
| 5610 |
for (queue_num = 0; queue_num < B43_QOS_QUEUE_NUM; queue_num++) { |
| 5611 |
skb_queue_head_init(&wl->tx_queue[queue_num]); |
| 5612 |
wl->tx_queue_stopped[queue_num] = false; |
| 5613 |
} |
| 5614 |
|
| 5615 |
snprintf(chip_name, ARRAY_SIZE(chip_name), |
| 5616 |
(dev->chip_id > 0x9999) ? "%d" : "%04X", dev->chip_id); |
| 5617 |
b43info(wl, "Broadcom %s WLAN found (core revision %u)\n", chip_name, |
| 5618 |
dev->core_rev); |
| 5619 |
return wl; |
| 5620 |
} |
| 5621 |
|
| 5622 |
#ifdef CONFIG_B43_BCMA |
| 5623 |
static int b43_bcma_probe(struct bcma_device *core) |
| 5624 |
{ |
| 5625 |
struct b43_bus_dev *dev; |
| 5626 |
struct b43_wl *wl; |
| 5627 |
int err; |
| 5628 |
|
| 5629 |
if (!modparam_allhwsupport && |
| 5630 |
(core->id.rev == 0x17 || core->id.rev == 0x18)) { |
| 5631 |
pr_err("Support for cores revisions 0x17 and 0x18 disabled by module param allhwsupport=0. Try b43.allhwsupport=1\n"); |
| 5632 |
return -ENOTSUPP; |
| 5633 |
} |
| 5634 |
|
| 5635 |
dev = b43_bus_dev_bcma_init(core); |
| 5636 |
if (!dev) |
| 5637 |
return -ENODEV; |
| 5638 |
|
| 5639 |
wl = b43_wireless_init(dev); |
| 5640 |
if (IS_ERR(wl)) { |
| 5641 |
err = PTR_ERR(wl); |
| 5642 |
goto bcma_out; |
| 5643 |
} |
| 5644 |
|
| 5645 |
err = b43_one_core_attach(dev, wl); |
| 5646 |
if (err) |
| 5647 |
goto bcma_err_wireless_exit; |
| 5648 |
|
| 5649 |
/* setup and start work to load firmware */ |
| 5650 |
INIT_WORK(&wl->firmware_load, b43_request_firmware); |
| 5651 |
schedule_work(&wl->firmware_load); |
| 5652 |
|
| 5653 |
return err; |
| 5654 |
|
| 5655 |
bcma_err_wireless_exit: |
| 5656 |
ieee80211_free_hw(wl->hw); |
| 5657 |
bcma_out: |
| 5658 |
kfree(dev); |
| 5659 |
return err; |
| 5660 |
} |
| 5661 |
|
| 5662 |
static void b43_bcma_remove(struct bcma_device *core) |
| 5663 |
{ |
| 5664 |
struct b43_wldev *wldev = bcma_get_drvdata(core); |
| 5665 |
struct b43_wl *wl = wldev->wl; |
| 5666 |
|
| 5667 |
/* We must cancel any work here before unregistering from ieee80211, |
| 5668 |
* as the ieee80211 unreg will destroy the workqueue. */ |
| 5669 |
cancel_work_sync(&wldev->restart_work); |
| 5670 |
cancel_work_sync(&wl->firmware_load); |
| 5671 |
|
| 5672 |
B43_WARN_ON(!wl); |
| 5673 |
if (!wldev->fw.ucode.data) |
| 5674 |
return; /* NULL if firmware never loaded */ |
| 5675 |
if (wl->current_dev == wldev && wl->hw_registered) { |
| 5676 |
b43_leds_stop(wldev); |
| 5677 |
ieee80211_unregister_hw(wl->hw); |
| 5678 |
} |
| 5679 |
|
| 5680 |
b43_one_core_detach(wldev->dev); |
| 5681 |
|
| 5682 |
/* Unregister HW RNG driver */ |
| 5683 |
b43_rng_exit(wl); |
| 5684 |
|
| 5685 |
b43_leds_unregister(wl); |
| 5686 |
ieee80211_free_hw(wl->hw); |
| 5687 |
kfree(wldev->dev); |
| 5688 |
} |
| 5689 |
|
| 5690 |
static struct bcma_driver b43_bcma_driver = { |
| 5691 |
.name = KBUILD_MODNAME, |
| 5692 |
.id_table = b43_bcma_tbl, |
| 5693 |
.probe = b43_bcma_probe, |
| 5694 |
.remove = b43_bcma_remove, |
| 5695 |
}; |
| 5696 |
#endif |
| 5697 |
|
| 5698 |
#ifdef CONFIG_B43_SSB |
| 5699 |
static |
| 5700 |
int b43_ssb_probe(struct ssb_device *sdev, const struct ssb_device_id *id) |
| 5701 |
{ |
| 5702 |
struct b43_bus_dev *dev; |
| 5703 |
struct b43_wl *wl; |
| 5704 |
int err; |
| 5705 |
|
| 5706 |
dev = b43_bus_dev_ssb_init(sdev); |
| 5707 |
if (!dev) |
| 5708 |
return -ENOMEM; |
| 5709 |
|
| 5710 |
wl = ssb_get_devtypedata(sdev); |
| 5711 |
if (wl) { |
| 5712 |
b43err(NULL, "Dual-core devices are not supported\n"); |
| 5713 |
err = -ENOTSUPP; |
| 5714 |
goto err_ssb_kfree_dev; |
| 5715 |
} |
| 5716 |
|
| 5717 |
b43_sprom_fixup(sdev->bus); |
| 5718 |
|
| 5719 |
wl = b43_wireless_init(dev); |
| 5720 |
if (IS_ERR(wl)) { |
| 5721 |
err = PTR_ERR(wl); |
| 5722 |
goto err_ssb_kfree_dev; |
| 5723 |
} |
| 5724 |
ssb_set_devtypedata(sdev, wl); |
| 5725 |
B43_WARN_ON(ssb_get_devtypedata(sdev) != wl); |
| 5726 |
|
| 5727 |
err = b43_one_core_attach(dev, wl); |
| 5728 |
if (err) |
| 5729 |
goto err_ssb_wireless_exit; |
| 5730 |
|
| 5731 |
/* setup and start work to load firmware */ |
| 5732 |
INIT_WORK(&wl->firmware_load, b43_request_firmware); |
| 5733 |
schedule_work(&wl->firmware_load); |
| 5734 |
|
| 5735 |
return err; |
| 5736 |
|
| 5737 |
err_ssb_wireless_exit: |
| 5738 |
b43_wireless_exit(dev, wl); |
| 5739 |
err_ssb_kfree_dev: |
| 5740 |
kfree(dev); |
| 5741 |
return err; |
| 5742 |
} |
| 5743 |
|
| 5744 |
static void b43_ssb_remove(struct ssb_device *sdev) |
| 5745 |
{ |
| 5746 |
struct b43_wl *wl = ssb_get_devtypedata(sdev); |
| 5747 |
struct b43_wldev *wldev = ssb_get_drvdata(sdev); |
| 5748 |
struct b43_bus_dev *dev = wldev->dev; |
| 5749 |
|
| 5750 |
/* We must cancel any work here before unregistering from ieee80211, |
| 5751 |
* as the ieee80211 unreg will destroy the workqueue. */ |
| 5752 |
cancel_work_sync(&wldev->restart_work); |
| 5753 |
cancel_work_sync(&wl->firmware_load); |
| 5754 |
|
| 5755 |
B43_WARN_ON(!wl); |
| 5756 |
if (!wldev->fw.ucode.data) |
| 5757 |
return; /* NULL if firmware never loaded */ |
| 5758 |
if (wl->current_dev == wldev && wl->hw_registered) { |
| 5759 |
b43_leds_stop(wldev); |
| 5760 |
ieee80211_unregister_hw(wl->hw); |
| 5761 |
} |
| 5762 |
|
| 5763 |
b43_one_core_detach(dev); |
| 5764 |
|
| 5765 |
/* Unregister HW RNG driver */ |
| 5766 |
b43_rng_exit(wl); |
| 5767 |
|
| 5768 |
b43_leds_unregister(wl); |
| 5769 |
b43_wireless_exit(dev, wl); |
| 5770 |
kfree(dev); |
| 5771 |
} |
| 5772 |
|
| 5773 |
static struct ssb_driver b43_ssb_driver = { |
| 5774 |
.name = KBUILD_MODNAME, |
| 5775 |
.id_table = b43_ssb_tbl, |
| 5776 |
.probe = b43_ssb_probe, |
| 5777 |
.remove = b43_ssb_remove, |
| 5778 |
}; |
| 5779 |
#endif /* CONFIG_B43_SSB */ |
| 5780 |
|
| 5781 |
/* Perform a hardware reset. This can be called from any context. */ |
| 5782 |
void b43_controller_restart(struct b43_wldev *dev, const char *reason) |
| 5783 |
{ |
| 5784 |
/* Must avoid requeueing, if we are in shutdown. */ |
| 5785 |
if (b43_status(dev) < B43_STAT_INITIALIZED) |
| 5786 |
return; |
| 5787 |
b43info(dev->wl, "Controller RESET (%s) ...\n", reason); |
| 5788 |
ieee80211_queue_work(dev->wl->hw, &dev->restart_work); |
| 5789 |
} |
| 5790 |
|
| 5791 |
static void b43_print_driverinfo(void) |
| 5792 |
{ |
| 5793 |
const char *feat_pci = "", *feat_nphy = "", |
| 5794 |
*feat_leds = "", *feat_sdio = ""; |
| 5795 |
|
| 5796 |
#ifdef CONFIG_B43_PCI_AUTOSELECT |
| 5797 |
feat_pci = "P"; |
| 5798 |
#endif |
| 5799 |
#ifdef CONFIG_B43_PHY_N |
| 5800 |
feat_nphy = "N"; |
| 5801 |
#endif |
| 5802 |
#ifdef CONFIG_B43_LEDS |
| 5803 |
feat_leds = "L"; |
| 5804 |
#endif |
| 5805 |
#ifdef CONFIG_B43_SDIO |
| 5806 |
feat_sdio = "S"; |
| 5807 |
#endif |
| 5808 |
printk(KERN_INFO "Broadcom 43xx driver loaded " |
| 5809 |
"[ Features: %s%s%s%s ]\n", |
| 5810 |
feat_pci, feat_nphy, feat_leds, feat_sdio); |
| 5811 |
} |
| 5812 |
|
| 5813 |
static int __init b43_init(void) |
| 5814 |
{ |
| 5815 |
int err; |
| 5816 |
|
| 5817 |
b43_debugfs_init(); |
| 5818 |
err = b43_sdio_init(); |
| 5819 |
if (err) |
| 5820 |
goto err_dfs_exit; |
| 5821 |
#ifdef CONFIG_B43_BCMA |
| 5822 |
err = bcma_driver_register(&b43_bcma_driver); |
| 5823 |
if (err) |
| 5824 |
goto err_sdio_exit; |
| 5825 |
#endif |
| 5826 |
#ifdef CONFIG_B43_SSB |
| 5827 |
err = ssb_driver_register(&b43_ssb_driver); |
| 5828 |
if (err) |
| 5829 |
goto err_bcma_driver_exit; |
| 5830 |
#endif |
| 5831 |
b43_print_driverinfo(); |
| 5832 |
|
| 5833 |
return err; |
| 5834 |
|
| 5835 |
#ifdef CONFIG_B43_SSB |
| 5836 |
err_bcma_driver_exit: |
| 5837 |
#endif |
| 5838 |
#ifdef CONFIG_B43_BCMA |
| 5839 |
bcma_driver_unregister(&b43_bcma_driver); |
| 5840 |
err_sdio_exit: |
| 5841 |
#endif |
| 5842 |
b43_sdio_exit(); |
| 5843 |
err_dfs_exit: |
| 5844 |
b43_debugfs_exit(); |
| 5845 |
return err; |
| 5846 |
} |
| 5847 |
|
| 5848 |
static void __exit b43_exit(void) |
| 5849 |
{ |
| 5850 |
#ifdef CONFIG_B43_SSB |
| 5851 |
ssb_driver_unregister(&b43_ssb_driver); |
| 5852 |
#endif |
| 5853 |
#ifdef CONFIG_B43_BCMA |
| 5854 |
bcma_driver_unregister(&b43_bcma_driver); |
| 5855 |
#endif |
| 5856 |
b43_sdio_exit(); |
| 5857 |
b43_debugfs_exit(); |
| 5858 |
} |
| 5859 |
|
| 5860 |
module_init(b43_init) |
| 5861 |
module_exit(b43_exit) |