| 1 |
/* SPDX-License-Identifier: ISC */ |
| 2 |
/* |
| 3 |
* Copyright (c) 2005-2011 Atheros Communications Inc. |
| 4 |
* Copyright (c) 2011-2017 Qualcomm Atheros, Inc. |
| 5 |
* Copyright (c) 2018 The Linux Foundation. All rights reserved. |
| 6 |
* Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved. |
| 7 |
*/ |
| 8 |
|
| 9 |
#ifndef _HW_H_ |
| 10 |
#define _HW_H_ |
| 11 |
|
| 12 |
#include "targaddrs.h" |
| 13 |
|
| 14 |
enum ath10k_bus { |
| 15 |
ATH10K_BUS_PCI, |
| 16 |
ATH10K_BUS_AHB, |
| 17 |
ATH10K_BUS_SDIO, |
| 18 |
ATH10K_BUS_USB, |
| 19 |
ATH10K_BUS_SNOC, |
| 20 |
}; |
| 21 |
|
| 22 |
#define ATH10K_FW_DIR "ath10k" |
| 23 |
|
| 24 |
#define QCA988X_2_0_DEVICE_ID_UBNT (0x11ac) |
| 25 |
#define QCA988X_2_0_DEVICE_ID (0x003c) |
| 26 |
#define QCA6164_2_1_DEVICE_ID (0x0041) |
| 27 |
#define QCA6174_2_1_DEVICE_ID (0x003e) |
| 28 |
#define QCA6174_3_2_DEVICE_ID (0x0042) |
| 29 |
#define QCA99X0_2_0_DEVICE_ID (0x0040) |
| 30 |
#define QCA9888_2_0_DEVICE_ID (0x0056) |
| 31 |
#define QCA9984_1_0_DEVICE_ID (0x0046) |
| 32 |
#define QCA9377_1_0_DEVICE_ID (0x0042) |
| 33 |
#define QCA9887_1_0_DEVICE_ID (0x0050) |
| 34 |
|
| 35 |
/* QCA988X 1.0 definitions (unsupported) */ |
| 36 |
#define QCA988X_HW_1_0_CHIP_ID_REV 0x0 |
| 37 |
|
| 38 |
/* QCA988X 2.0 definitions */ |
| 39 |
#define QCA988X_HW_2_0_VERSION 0x4100016c |
| 40 |
#define QCA988X_HW_2_0_CHIP_ID_REV 0x2 |
| 41 |
#define QCA988X_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA988X/hw2.0" |
| 42 |
#define QCA988X_HW_2_0_PATCH_LOAD_ADDR 0x1234 |
| 43 |
|
| 44 |
/* QCA9887 1.0 definitions */ |
| 45 |
#define QCA9887_HW_1_0_VERSION 0x4100016d |
| 46 |
#define QCA9887_HW_1_0_CHIP_ID_REV 0 |
| 47 |
#define QCA9887_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9887/hw1.0" |
| 48 |
#define QCA9887_HW_1_0_PATCH_LOAD_ADDR 0x1234 |
| 49 |
|
| 50 |
/* QCA6174 target BMI version signatures */ |
| 51 |
#define QCA6174_HW_1_0_VERSION 0x05000000 |
| 52 |
#define QCA6174_HW_1_1_VERSION 0x05000001 |
| 53 |
#define QCA6174_HW_1_3_VERSION 0x05000003 |
| 54 |
#define QCA6174_HW_2_1_VERSION 0x05010000 |
| 55 |
#define QCA6174_HW_3_0_VERSION 0x05020000 |
| 56 |
#define QCA6174_HW_3_2_VERSION 0x05030000 |
| 57 |
|
| 58 |
/* QCA9377 target BMI version signatures */ |
| 59 |
#define QCA9377_HW_1_0_DEV_VERSION 0x05020000 |
| 60 |
#define QCA9377_HW_1_1_DEV_VERSION 0x05020001 |
| 61 |
|
| 62 |
enum qca6174_pci_rev { |
| 63 |
QCA6174_PCI_REV_1_1 = 0x11, |
| 64 |
QCA6174_PCI_REV_1_3 = 0x13, |
| 65 |
QCA6174_PCI_REV_2_0 = 0x20, |
| 66 |
QCA6174_PCI_REV_3_0 = 0x30, |
| 67 |
}; |
| 68 |
|
| 69 |
enum qca6174_chip_id_rev { |
| 70 |
QCA6174_HW_1_0_CHIP_ID_REV = 0, |
| 71 |
QCA6174_HW_1_1_CHIP_ID_REV = 1, |
| 72 |
QCA6174_HW_1_3_CHIP_ID_REV = 2, |
| 73 |
QCA6174_HW_2_1_CHIP_ID_REV = 4, |
| 74 |
QCA6174_HW_2_2_CHIP_ID_REV = 5, |
| 75 |
QCA6174_HW_3_0_CHIP_ID_REV = 8, |
| 76 |
QCA6174_HW_3_1_CHIP_ID_REV = 9, |
| 77 |
QCA6174_HW_3_2_CHIP_ID_REV = 10, |
| 78 |
}; |
| 79 |
|
| 80 |
enum qca9377_chip_id_rev { |
| 81 |
QCA9377_HW_1_0_CHIP_ID_REV = 0x0, |
| 82 |
QCA9377_HW_1_1_CHIP_ID_REV = 0x1, |
| 83 |
}; |
| 84 |
|
| 85 |
#define QCA6174_HW_2_1_FW_DIR ATH10K_FW_DIR "/QCA6174/hw2.1" |
| 86 |
#define QCA6174_HW_2_1_PATCH_LOAD_ADDR 0x1234 |
| 87 |
|
| 88 |
#define QCA6174_HW_3_0_FW_DIR ATH10K_FW_DIR "/QCA6174/hw3.0" |
| 89 |
#define QCA6174_HW_3_0_PATCH_LOAD_ADDR 0x1234 |
| 90 |
|
| 91 |
/* QCA99X0 1.0 definitions (unsupported) */ |
| 92 |
#define QCA99X0_HW_1_0_CHIP_ID_REV 0x0 |
| 93 |
|
| 94 |
/* QCA99X0 2.0 definitions */ |
| 95 |
#define QCA99X0_HW_2_0_DEV_VERSION 0x01000000 |
| 96 |
#define QCA99X0_HW_2_0_CHIP_ID_REV 0x1 |
| 97 |
#define QCA99X0_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA99X0/hw2.0" |
| 98 |
#define QCA99X0_HW_2_0_PATCH_LOAD_ADDR 0x1234 |
| 99 |
|
| 100 |
/* QCA9984 1.0 defines */ |
| 101 |
#define QCA9984_HW_1_0_DEV_VERSION 0x1000000 |
| 102 |
#define QCA9984_HW_DEV_TYPE 0xa |
| 103 |
#define QCA9984_HW_1_0_CHIP_ID_REV 0x0 |
| 104 |
#define QCA9984_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9984/hw1.0" |
| 105 |
#define QCA9984_HW_1_0_PATCH_LOAD_ADDR 0x1234 |
| 106 |
|
| 107 |
/* QCA9888 2.0 defines */ |
| 108 |
#define QCA9888_HW_2_0_DEV_VERSION 0x1000000 |
| 109 |
#define QCA9888_HW_DEV_TYPE 0xc |
| 110 |
#define QCA9888_HW_2_0_CHIP_ID_REV 0x0 |
| 111 |
#define QCA9888_HW_2_0_FW_DIR ATH10K_FW_DIR "/QCA9888/hw2.0" |
| 112 |
#define QCA9888_HW_2_0_PATCH_LOAD_ADDR 0x1234 |
| 113 |
|
| 114 |
/* QCA9377 1.0 definitions */ |
| 115 |
#define QCA9377_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA9377/hw1.0" |
| 116 |
#define QCA9377_HW_1_0_PATCH_LOAD_ADDR 0x1234 |
| 117 |
|
| 118 |
/* QCA4019 1.0 definitions */ |
| 119 |
#define QCA4019_HW_1_0_DEV_VERSION 0x01000000 |
| 120 |
#define QCA4019_HW_1_0_FW_DIR ATH10K_FW_DIR "/QCA4019/hw1.0" |
| 121 |
#define QCA4019_HW_1_0_PATCH_LOAD_ADDR 0x1234 |
| 122 |
|
| 123 |
/* WCN3990 1.0 definitions */ |
| 124 |
#define WCN3990_HW_1_0_DEV_VERSION ATH10K_HW_WCN3990 |
| 125 |
#define WCN3990_HW_1_0_FW_DIR ATH10K_FW_DIR "/WCN3990/hw1.0" |
| 126 |
|
| 127 |
#define ATH10K_FW_FILE_BASE "firmware" |
| 128 |
#define ATH10K_FW_API_MAX 6 |
| 129 |
#define ATH10K_FW_API_MIN 2 |
| 130 |
|
| 131 |
#define ATH10K_FW_API2_FILE "firmware-2.bin" |
| 132 |
#define ATH10K_FW_API3_FILE "firmware-3.bin" |
| 133 |
|
| 134 |
/* added support for ATH10K_FW_IE_WMI_OP_VERSION */ |
| 135 |
#define ATH10K_FW_API4_FILE "firmware-4.bin" |
| 136 |
|
| 137 |
/* HTT id conflict fix for management frames over HTT */ |
| 138 |
#define ATH10K_FW_API5_FILE "firmware-5.bin" |
| 139 |
|
| 140 |
/* the firmware-6.bin blob */ |
| 141 |
#define ATH10K_FW_API6_FILE "firmware-6.bin" |
| 142 |
|
| 143 |
#define ATH10K_FW_UTF_FILE "utf.bin" |
| 144 |
#define ATH10K_FW_UTF_API2_FILE "utf-2.bin" |
| 145 |
|
| 146 |
#define ATH10K_FW_UTF_FILE_BASE "utf" |
| 147 |
|
| 148 |
/* includes also the null byte */ |
| 149 |
#define ATH10K_FIRMWARE_MAGIC "QCA-ATH10K" |
| 150 |
#define ATH10K_BOARD_MAGIC "QCA-ATH10K-BOARD" |
| 151 |
|
| 152 |
#define ATH10K_BOARD_DATA_FILE "board.bin" |
| 153 |
#define ATH10K_BOARD_API2_FILE "board-2.bin" |
| 154 |
#define ATH10K_EBOARD_DATA_FILE "eboard.bin" |
| 155 |
|
| 156 |
#define REG_DUMP_COUNT_QCA988X 60 |
| 157 |
|
| 158 |
struct ath10k_fw_ie { |
| 159 |
__le32 id; |
| 160 |
__le32 len; |
| 161 |
u8 data[]; |
| 162 |
}; |
| 163 |
|
| 164 |
enum ath10k_fw_ie_type { |
| 165 |
ATH10K_FW_IE_FW_VERSION = 0, |
| 166 |
ATH10K_FW_IE_TIMESTAMP = 1, |
| 167 |
ATH10K_FW_IE_FEATURES = 2, |
| 168 |
ATH10K_FW_IE_FW_IMAGE = 3, |
| 169 |
ATH10K_FW_IE_OTP_IMAGE = 4, |
| 170 |
|
| 171 |
/* WMI "operations" interface version, 32 bit value. Supported from |
| 172 |
* FW API 4 and above. |
| 173 |
*/ |
| 174 |
ATH10K_FW_IE_WMI_OP_VERSION = 5, |
| 175 |
|
| 176 |
/* HTT "operations" interface version, 32 bit value. Supported from |
| 177 |
* FW API 5 and above. |
| 178 |
*/ |
| 179 |
ATH10K_FW_IE_HTT_OP_VERSION = 6, |
| 180 |
|
| 181 |
/* Code swap image for firmware binary */ |
| 182 |
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE = 7, |
| 183 |
}; |
| 184 |
|
| 185 |
enum ath10k_fw_wmi_op_version { |
| 186 |
ATH10K_FW_WMI_OP_VERSION_UNSET = 0, |
| 187 |
|
| 188 |
ATH10K_FW_WMI_OP_VERSION_MAIN = 1, |
| 189 |
ATH10K_FW_WMI_OP_VERSION_10_1 = 2, |
| 190 |
ATH10K_FW_WMI_OP_VERSION_10_2 = 3, |
| 191 |
ATH10K_FW_WMI_OP_VERSION_TLV = 4, |
| 192 |
ATH10K_FW_WMI_OP_VERSION_10_2_4 = 5, |
| 193 |
ATH10K_FW_WMI_OP_VERSION_10_4 = 6, |
| 194 |
|
| 195 |
/* keep last */ |
| 196 |
ATH10K_FW_WMI_OP_VERSION_MAX, |
| 197 |
}; |
| 198 |
|
| 199 |
enum ath10k_fw_htt_op_version { |
| 200 |
ATH10K_FW_HTT_OP_VERSION_UNSET = 0, |
| 201 |
|
| 202 |
ATH10K_FW_HTT_OP_VERSION_MAIN = 1, |
| 203 |
|
| 204 |
/* also used in 10.2 and 10.2.4 branches */ |
| 205 |
ATH10K_FW_HTT_OP_VERSION_10_1 = 2, |
| 206 |
|
| 207 |
ATH10K_FW_HTT_OP_VERSION_TLV = 3, |
| 208 |
|
| 209 |
ATH10K_FW_HTT_OP_VERSION_10_4 = 4, |
| 210 |
|
| 211 |
/* keep last */ |
| 212 |
ATH10K_FW_HTT_OP_VERSION_MAX, |
| 213 |
}; |
| 214 |
|
| 215 |
enum ath10k_bd_ie_type { |
| 216 |
/* contains sub IEs of enum ath10k_bd_ie_board_type */ |
| 217 |
ATH10K_BD_IE_BOARD = 0, |
| 218 |
ATH10K_BD_IE_BOARD_EXT = 1, |
| 219 |
}; |
| 220 |
|
| 221 |
enum ath10k_bd_ie_board_type { |
| 222 |
ATH10K_BD_IE_BOARD_NAME = 0, |
| 223 |
ATH10K_BD_IE_BOARD_DATA = 1, |
| 224 |
}; |
| 225 |
|
| 226 |
enum ath10k_hw_rev { |
| 227 |
ATH10K_HW_QCA988X, |
| 228 |
ATH10K_HW_QCA6174, |
| 229 |
ATH10K_HW_QCA99X0, |
| 230 |
ATH10K_HW_QCA9888, |
| 231 |
ATH10K_HW_QCA9984, |
| 232 |
ATH10K_HW_QCA9377, |
| 233 |
ATH10K_HW_QCA4019, |
| 234 |
ATH10K_HW_QCA9887, |
| 235 |
ATH10K_HW_WCN3990, |
| 236 |
}; |
| 237 |
|
| 238 |
struct ath10k_hw_regs { |
| 239 |
u32 rtc_soc_base_address; |
| 240 |
u32 rtc_wmac_base_address; |
| 241 |
u32 soc_core_base_address; |
| 242 |
u32 wlan_mac_base_address; |
| 243 |
u32 ce_wrapper_base_address; |
| 244 |
u32 ce0_base_address; |
| 245 |
u32 ce1_base_address; |
| 246 |
u32 ce2_base_address; |
| 247 |
u32 ce3_base_address; |
| 248 |
u32 ce4_base_address; |
| 249 |
u32 ce5_base_address; |
| 250 |
u32 ce6_base_address; |
| 251 |
u32 ce7_base_address; |
| 252 |
u32 ce8_base_address; |
| 253 |
u32 ce9_base_address; |
| 254 |
u32 ce10_base_address; |
| 255 |
u32 ce11_base_address; |
| 256 |
u32 soc_reset_control_si0_rst_mask; |
| 257 |
u32 soc_reset_control_ce_rst_mask; |
| 258 |
u32 soc_chip_id_address; |
| 259 |
u32 scratch_3_address; |
| 260 |
u32 fw_indicator_address; |
| 261 |
u32 pcie_local_base_address; |
| 262 |
u32 ce_wrap_intr_sum_host_msi_lsb; |
| 263 |
u32 ce_wrap_intr_sum_host_msi_mask; |
| 264 |
u32 pcie_intr_fw_mask; |
| 265 |
u32 pcie_intr_ce_mask_all; |
| 266 |
u32 pcie_intr_clr_address; |
| 267 |
u32 cpu_pll_init_address; |
| 268 |
u32 cpu_speed_address; |
| 269 |
u32 core_clk_div_address; |
| 270 |
}; |
| 271 |
|
| 272 |
extern const struct ath10k_hw_regs qca988x_regs; |
| 273 |
extern const struct ath10k_hw_regs qca6174_regs; |
| 274 |
extern const struct ath10k_hw_regs qca99x0_regs; |
| 275 |
extern const struct ath10k_hw_regs qca4019_regs; |
| 276 |
extern const struct ath10k_hw_regs wcn3990_regs; |
| 277 |
|
| 278 |
struct ath10k_hw_ce_regs_addr_map { |
| 279 |
u32 msb; |
| 280 |
u32 lsb; |
| 281 |
u32 mask; |
| 282 |
}; |
| 283 |
|
| 284 |
struct ath10k_hw_ce_ctrl1 { |
| 285 |
u32 addr; |
| 286 |
u32 hw_mask; |
| 287 |
u32 sw_mask; |
| 288 |
u32 hw_wr_mask; |
| 289 |
u32 sw_wr_mask; |
| 290 |
u32 reset_mask; |
| 291 |
u32 reset; |
| 292 |
const struct ath10k_hw_ce_regs_addr_map *src_ring; |
| 293 |
const struct ath10k_hw_ce_regs_addr_map *dst_ring; |
| 294 |
const struct ath10k_hw_ce_regs_addr_map *dmax; |
| 295 |
}; |
| 296 |
|
| 297 |
struct ath10k_hw_ce_cmd_halt { |
| 298 |
u32 status_reset; |
| 299 |
u32 msb; |
| 300 |
u32 mask; |
| 301 |
const struct ath10k_hw_ce_regs_addr_map *status; |
| 302 |
}; |
| 303 |
|
| 304 |
struct ath10k_hw_ce_host_ie { |
| 305 |
u32 copy_complete_reset; |
| 306 |
const struct ath10k_hw_ce_regs_addr_map *copy_complete; |
| 307 |
}; |
| 308 |
|
| 309 |
struct ath10k_hw_ce_host_wm_regs { |
| 310 |
u32 dstr_lmask; |
| 311 |
u32 dstr_hmask; |
| 312 |
u32 srcr_lmask; |
| 313 |
u32 srcr_hmask; |
| 314 |
u32 cc_mask; |
| 315 |
u32 wm_mask; |
| 316 |
u32 addr; |
| 317 |
}; |
| 318 |
|
| 319 |
struct ath10k_hw_ce_misc_regs { |
| 320 |
u32 axi_err; |
| 321 |
u32 dstr_add_err; |
| 322 |
u32 srcr_len_err; |
| 323 |
u32 dstr_mlen_vio; |
| 324 |
u32 dstr_overflow; |
| 325 |
u32 srcr_overflow; |
| 326 |
u32 err_mask; |
| 327 |
u32 addr; |
| 328 |
}; |
| 329 |
|
| 330 |
struct ath10k_hw_ce_dst_src_wm_regs { |
| 331 |
u32 addr; |
| 332 |
u32 low_rst; |
| 333 |
u32 high_rst; |
| 334 |
const struct ath10k_hw_ce_regs_addr_map *wm_low; |
| 335 |
const struct ath10k_hw_ce_regs_addr_map *wm_high; |
| 336 |
}; |
| 337 |
|
| 338 |
struct ath10k_hw_ce_ctrl1_upd { |
| 339 |
u32 shift; |
| 340 |
u32 mask; |
| 341 |
u32 enable; |
| 342 |
}; |
| 343 |
|
| 344 |
struct ath10k_hw_ce_regs { |
| 345 |
u32 sr_base_addr_lo; |
| 346 |
u32 sr_base_addr_hi; |
| 347 |
u32 sr_size_addr; |
| 348 |
u32 dr_base_addr_lo; |
| 349 |
u32 dr_base_addr_hi; |
| 350 |
u32 dr_size_addr; |
| 351 |
u32 ce_cmd_addr; |
| 352 |
u32 misc_ie_addr; |
| 353 |
u32 sr_wr_index_addr; |
| 354 |
u32 dst_wr_index_addr; |
| 355 |
u32 current_srri_addr; |
| 356 |
u32 current_drri_addr; |
| 357 |
u32 ddr_addr_for_rri_low; |
| 358 |
u32 ddr_addr_for_rri_high; |
| 359 |
u32 ce_rri_low; |
| 360 |
u32 ce_rri_high; |
| 361 |
u32 host_ie_addr; |
| 362 |
const struct ath10k_hw_ce_host_wm_regs *wm_regs; |
| 363 |
const struct ath10k_hw_ce_misc_regs *misc_regs; |
| 364 |
const struct ath10k_hw_ce_ctrl1 *ctrl1_regs; |
| 365 |
const struct ath10k_hw_ce_cmd_halt *cmd_halt; |
| 366 |
const struct ath10k_hw_ce_host_ie *host_ie; |
| 367 |
const struct ath10k_hw_ce_dst_src_wm_regs *wm_srcr; |
| 368 |
const struct ath10k_hw_ce_dst_src_wm_regs *wm_dstr; |
| 369 |
const struct ath10k_hw_ce_ctrl1_upd *upd; |
| 370 |
}; |
| 371 |
|
| 372 |
struct ath10k_hw_values { |
| 373 |
u32 rtc_state_val_on; |
| 374 |
u8 ce_count; |
| 375 |
u8 msi_assign_ce_max; |
| 376 |
u8 num_target_ce_config_wlan; |
| 377 |
u16 ce_desc_meta_data_mask; |
| 378 |
u8 ce_desc_meta_data_lsb; |
| 379 |
u32 rfkill_pin; |
| 380 |
u32 rfkill_cfg; |
| 381 |
bool rfkill_on_level; |
| 382 |
}; |
| 383 |
|
| 384 |
extern const struct ath10k_hw_values qca988x_values; |
| 385 |
extern const struct ath10k_hw_values qca6174_values; |
| 386 |
extern const struct ath10k_hw_values qca99x0_values; |
| 387 |
extern const struct ath10k_hw_values qca9888_values; |
| 388 |
extern const struct ath10k_hw_values qca4019_values; |
| 389 |
extern const struct ath10k_hw_values wcn3990_values; |
| 390 |
extern const struct ath10k_hw_ce_regs wcn3990_ce_regs; |
| 391 |
extern const struct ath10k_hw_ce_regs qcax_ce_regs; |
| 392 |
|
| 393 |
void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey, |
| 394 |
u32 cc, u32 rcc, u32 cc_prev, u32 rcc_prev); |
| 395 |
|
| 396 |
int ath10k_hw_diag_fast_download(struct ath10k *ar, |
| 397 |
u32 address, |
| 398 |
const void *buffer, |
| 399 |
u32 length); |
| 400 |
|
| 401 |
#define QCA_REV_988X(ar) ((ar)->hw_rev == ATH10K_HW_QCA988X) |
| 402 |
#define QCA_REV_9887(ar) ((ar)->hw_rev == ATH10K_HW_QCA9887) |
| 403 |
#define QCA_REV_6174(ar) ((ar)->hw_rev == ATH10K_HW_QCA6174) |
| 404 |
#define QCA_REV_99X0(ar) ((ar)->hw_rev == ATH10K_HW_QCA99X0) |
| 405 |
#define QCA_REV_9888(ar) ((ar)->hw_rev == ATH10K_HW_QCA9888) |
| 406 |
#define QCA_REV_9984(ar) ((ar)->hw_rev == ATH10K_HW_QCA9984) |
| 407 |
#define QCA_REV_9377(ar) ((ar)->hw_rev == ATH10K_HW_QCA9377) |
| 408 |
#define QCA_REV_40XX(ar) ((ar)->hw_rev == ATH10K_HW_QCA4019) |
| 409 |
#define QCA_REV_WCN3990(ar) ((ar)->hw_rev == ATH10K_HW_WCN3990) |
| 410 |
|
| 411 |
/* Known peculiarities: |
| 412 |
* - raw appears in nwifi decap, raw and nwifi appear in ethernet decap |
| 413 |
* - raw have FCS, nwifi doesn't |
| 414 |
* - ethernet frames have 802.11 header decapped and parts (base hdr, cipher |
| 415 |
* param, llc/snap) are aligned to 4byte boundaries each |
| 416 |
*/ |
| 417 |
enum ath10k_hw_txrx_mode { |
| 418 |
ATH10K_HW_TXRX_RAW = 0, |
| 419 |
|
| 420 |
/* Native Wifi decap mode is used to align IP frames to 4-byte |
| 421 |
* boundaries and avoid a very expensive re-alignment in mac80211. |
| 422 |
*/ |
| 423 |
ATH10K_HW_TXRX_NATIVE_WIFI = 1, |
| 424 |
ATH10K_HW_TXRX_ETHERNET = 2, |
| 425 |
|
| 426 |
/* Valid for HTT >= 3.0. Used for management frames in TX_FRM. */ |
| 427 |
ATH10K_HW_TXRX_MGMT = 3, |
| 428 |
}; |
| 429 |
|
| 430 |
enum ath10k_mcast2ucast_mode { |
| 431 |
ATH10K_MCAST2UCAST_DISABLED = 0, |
| 432 |
ATH10K_MCAST2UCAST_ENABLED = 1, |
| 433 |
}; |
| 434 |
|
| 435 |
enum ath10k_hw_rate_ofdm { |
| 436 |
ATH10K_HW_RATE_OFDM_48M = 0, |
| 437 |
ATH10K_HW_RATE_OFDM_24M, |
| 438 |
ATH10K_HW_RATE_OFDM_12M, |
| 439 |
ATH10K_HW_RATE_OFDM_6M, |
| 440 |
ATH10K_HW_RATE_OFDM_54M, |
| 441 |
ATH10K_HW_RATE_OFDM_36M, |
| 442 |
ATH10K_HW_RATE_OFDM_18M, |
| 443 |
ATH10K_HW_RATE_OFDM_9M, |
| 444 |
}; |
| 445 |
|
| 446 |
enum ath10k_hw_rate_cck { |
| 447 |
ATH10K_HW_RATE_CCK_LP_11M = 0, |
| 448 |
ATH10K_HW_RATE_CCK_LP_5_5M, |
| 449 |
ATH10K_HW_RATE_CCK_LP_2M, |
| 450 |
ATH10K_HW_RATE_CCK_LP_1M, |
| 451 |
ATH10K_HW_RATE_CCK_SP_11M, |
| 452 |
ATH10K_HW_RATE_CCK_SP_5_5M, |
| 453 |
ATH10K_HW_RATE_CCK_SP_2M, |
| 454 |
}; |
| 455 |
|
| 456 |
enum ath10k_hw_rate_rev2_cck { |
| 457 |
ATH10K_HW_RATE_REV2_CCK_LP_1M = 1, |
| 458 |
ATH10K_HW_RATE_REV2_CCK_LP_2M, |
| 459 |
ATH10K_HW_RATE_REV2_CCK_LP_5_5M, |
| 460 |
ATH10K_HW_RATE_REV2_CCK_LP_11M, |
| 461 |
ATH10K_HW_RATE_REV2_CCK_SP_2M, |
| 462 |
ATH10K_HW_RATE_REV2_CCK_SP_5_5M, |
| 463 |
ATH10K_HW_RATE_REV2_CCK_SP_11M, |
| 464 |
}; |
| 465 |
|
| 466 |
enum ath10k_hw_cc_wraparound_type { |
| 467 |
ATH10K_HW_CC_WRAP_DISABLED = 0, |
| 468 |
|
| 469 |
/* This type is when the HW chip has a quirky Cycle Counter |
| 470 |
* wraparound which resets to 0x7fffffff instead of 0. All |
| 471 |
* other CC related counters (e.g. Rx Clear Count) are divided |
| 472 |
* by 2 so they never wraparound themselves. |
| 473 |
*/ |
| 474 |
ATH10K_HW_CC_WRAP_SHIFTED_ALL = 1, |
| 475 |
|
| 476 |
/* Each hw counter wraps around independently. When the |
| 477 |
* counter overflows the respective counter is right shifted |
| 478 |
* by 1, i.e reset to 0x7fffffff, and other counters will be |
| 479 |
* running unaffected. In this type of wraparound, it should |
| 480 |
* be possible to report accurate Rx busy time unlike the |
| 481 |
* first type. |
| 482 |
*/ |
| 483 |
ATH10K_HW_CC_WRAP_SHIFTED_EACH = 2, |
| 484 |
}; |
| 485 |
|
| 486 |
enum ath10k_hw_refclk_speed { |
| 487 |
ATH10K_HW_REFCLK_UNKNOWN = -1, |
| 488 |
ATH10K_HW_REFCLK_48_MHZ = 0, |
| 489 |
ATH10K_HW_REFCLK_19_2_MHZ = 1, |
| 490 |
ATH10K_HW_REFCLK_24_MHZ = 2, |
| 491 |
ATH10K_HW_REFCLK_26_MHZ = 3, |
| 492 |
ATH10K_HW_REFCLK_37_4_MHZ = 4, |
| 493 |
ATH10K_HW_REFCLK_38_4_MHZ = 5, |
| 494 |
ATH10K_HW_REFCLK_40_MHZ = 6, |
| 495 |
ATH10K_HW_REFCLK_52_MHZ = 7, |
| 496 |
|
| 497 |
/* must be the last one */ |
| 498 |
ATH10K_HW_REFCLK_COUNT, |
| 499 |
}; |
| 500 |
|
| 501 |
struct ath10k_hw_clk_params { |
| 502 |
u32 refclk; |
| 503 |
u32 div; |
| 504 |
u32 rnfrac; |
| 505 |
u32 settle_time; |
| 506 |
u32 refdiv; |
| 507 |
u32 outdiv; |
| 508 |
}; |
| 509 |
|
| 510 |
struct htt_rx_desc_ops; |
| 511 |
|
| 512 |
struct ath10k_hw_params { |
| 513 |
u32 id; |
| 514 |
u16 dev_id; |
| 515 |
enum ath10k_bus bus; |
| 516 |
const char *name; |
| 517 |
u32 patch_load_addr; |
| 518 |
int uart_pin; |
| 519 |
int led_pin; |
| 520 |
u32 otp_exe_param; |
| 521 |
|
| 522 |
/* Type of hw cycle counter wraparound logic, for more info |
| 523 |
* refer enum ath10k_hw_cc_wraparound_type. |
| 524 |
*/ |
| 525 |
enum ath10k_hw_cc_wraparound_type cc_wraparound_type; |
| 526 |
|
| 527 |
/* Some of chip expects fragment descriptor to be continuous |
| 528 |
* memory for any TX operation. Set continuous_frag_desc flag |
| 529 |
* for the hardware which have such requirement. |
| 530 |
*/ |
| 531 |
bool continuous_frag_desc; |
| 532 |
|
| 533 |
/* CCK hardware rate table mapping for the newer chipsets |
| 534 |
* like QCA99X0, QCA4019 got revised. The CCK h/w rate values |
| 535 |
* are in a proper order with respect to the rate/preamble |
| 536 |
*/ |
| 537 |
bool cck_rate_map_rev2; |
| 538 |
|
| 539 |
u32 channel_counters_freq_hz; |
| 540 |
|
| 541 |
/* Mgmt tx descriptors threshold for limiting probe response |
| 542 |
* frames. |
| 543 |
*/ |
| 544 |
u32 max_probe_resp_desc_thres; |
| 545 |
|
| 546 |
u32 tx_chain_mask; |
| 547 |
u32 rx_chain_mask; |
| 548 |
u32 max_spatial_stream; |
| 549 |
u32 cal_data_len; |
| 550 |
|
| 551 |
struct ath10k_hw_params_fw { |
| 552 |
const char *dir; |
| 553 |
size_t board_size; |
| 554 |
size_t ext_board_size; |
| 555 |
size_t board_ext_size; |
| 556 |
} fw; |
| 557 |
|
| 558 |
/* qca99x0 family chips deliver broadcast/multicast management |
| 559 |
* frames encrypted and expect software do decryption. |
| 560 |
*/ |
| 561 |
bool sw_decrypt_mcast_mgmt; |
| 562 |
|
| 563 |
/* Rx descriptor abstraction */ |
| 564 |
const struct ath10k_htt_rx_desc_ops *rx_desc_ops; |
| 565 |
|
| 566 |
const struct ath10k_hw_ops *hw_ops; |
| 567 |
|
| 568 |
/* Number of bytes used for alignment in rx_hdr_status of rx desc. */ |
| 569 |
int decap_align_bytes; |
| 570 |
|
| 571 |
/* hw specific clock control parameters */ |
| 572 |
const struct ath10k_hw_clk_params *hw_clk; |
| 573 |
int target_cpu_freq; |
| 574 |
|
| 575 |
/* Number of bytes to be discarded for each FFT sample */ |
| 576 |
int spectral_bin_discard; |
| 577 |
|
| 578 |
/* The board may have a restricted NSS for 160 or 80+80 vs what it |
| 579 |
* can do for 80Mhz. |
| 580 |
*/ |
| 581 |
int vht160_mcs_rx_highest; |
| 582 |
int vht160_mcs_tx_highest; |
| 583 |
|
| 584 |
/* Number of ciphers supported (i.e First N) in cipher_suites array */ |
| 585 |
int n_cipher_suites; |
| 586 |
|
| 587 |
u32 num_peers; |
| 588 |
u32 ast_skid_limit; |
| 589 |
u32 num_wds_entries; |
| 590 |
|
| 591 |
/* Targets supporting physical addressing capability above 32-bits */ |
| 592 |
bool target_64bit; |
| 593 |
|
| 594 |
/* Target rx ring fill level */ |
| 595 |
u32 rx_ring_fill_level; |
| 596 |
|
| 597 |
/* target supporting shadow register for ce write */ |
| 598 |
bool shadow_reg_support; |
| 599 |
|
| 600 |
/* target supporting retention restore on ddr */ |
| 601 |
bool rri_on_ddr; |
| 602 |
|
| 603 |
/* Number of bytes to be the offset for each FFT sample */ |
| 604 |
int spectral_bin_offset; |
| 605 |
|
| 606 |
/* targets which require hw filter reset during boot up, |
| 607 |
* to avoid it sending spurious acks. |
| 608 |
*/ |
| 609 |
bool hw_filter_reset_required; |
| 610 |
|
| 611 |
/* target supporting fw download via diag ce */ |
| 612 |
bool fw_diag_ce_download; |
| 613 |
|
| 614 |
/* target supporting fw download via large size BMI */ |
| 615 |
bool bmi_large_size_download; |
| 616 |
|
| 617 |
/* need to set uart pin if disable uart print, workaround for a |
| 618 |
* firmware bug |
| 619 |
*/ |
| 620 |
bool uart_pin_workaround; |
| 621 |
|
| 622 |
/* Workaround for the credit size calculation */ |
| 623 |
bool credit_size_workaround; |
| 624 |
|
| 625 |
/* tx stats support over pktlog */ |
| 626 |
bool tx_stats_over_pktlog; |
| 627 |
|
| 628 |
/* provides bitrates for sta_statistics using WMI_TLV_PEER_STATS_INFO_EVENTID */ |
| 629 |
bool supports_peer_stats_info; |
| 630 |
|
| 631 |
bool dynamic_sar_support; |
| 632 |
|
| 633 |
bool hw_restart_disconnect; |
| 634 |
|
| 635 |
bool use_fw_tx_credits; |
| 636 |
|
| 637 |
bool delay_unmap_buffer; |
| 638 |
|
| 639 |
/* The hardware support multicast frame registrations */ |
| 640 |
bool mcast_frame_registration; |
| 641 |
}; |
| 642 |
|
| 643 |
struct htt_resp; |
| 644 |
struct htt_data_tx_completion_ext; |
| 645 |
struct htt_rx_ring_rx_desc_offsets; |
| 646 |
|
| 647 |
/* Defines needed for Rx descriptor abstraction */ |
| 648 |
struct ath10k_hw_ops { |
| 649 |
void (*set_coverage_class)(struct ath10k *ar, int radio_idx, s16 value); |
| 650 |
int (*enable_pll_clk)(struct ath10k *ar); |
| 651 |
int (*tx_data_rssi_pad_bytes)(struct htt_resp *htt); |
| 652 |
int (*is_rssi_enable)(struct htt_resp *resp); |
| 653 |
}; |
| 654 |
|
| 655 |
extern const struct ath10k_hw_ops qca988x_ops; |
| 656 |
extern const struct ath10k_hw_ops qca99x0_ops; |
| 657 |
extern const struct ath10k_hw_ops qca6174_ops; |
| 658 |
extern const struct ath10k_hw_ops qca6174_sdio_ops; |
| 659 |
extern const struct ath10k_hw_ops wcn3990_ops; |
| 660 |
|
| 661 |
extern const struct ath10k_hw_clk_params qca6174_clk[]; |
| 662 |
|
| 663 |
static inline int |
| 664 |
ath10k_tx_data_rssi_get_pad_bytes(struct ath10k_hw_params *hw, |
| 665 |
struct htt_resp *htt) |
| 666 |
{ |
| 667 |
if (hw->hw_ops->tx_data_rssi_pad_bytes) |
| 668 |
return hw->hw_ops->tx_data_rssi_pad_bytes(htt); |
| 669 |
return 0; |
| 670 |
} |
| 671 |
|
| 672 |
static inline int |
| 673 |
ath10k_is_rssi_enable(struct ath10k_hw_params *hw, |
| 674 |
struct htt_resp *resp) |
| 675 |
{ |
| 676 |
if (hw->hw_ops->is_rssi_enable) |
| 677 |
return hw->hw_ops->is_rssi_enable(resp); |
| 678 |
return 0; |
| 679 |
} |
| 680 |
|
| 681 |
/* Target specific defines for MAIN firmware */ |
| 682 |
#define TARGET_NUM_VDEVS 8 |
| 683 |
#define TARGET_NUM_PEER_AST 2 |
| 684 |
#define TARGET_NUM_WDS_ENTRIES 32 |
| 685 |
#define TARGET_DMA_BURST_SIZE 0 |
| 686 |
#define TARGET_MAC_AGGR_DELIM 0 |
| 687 |
#define TARGET_AST_SKID_LIMIT 16 |
| 688 |
#define TARGET_NUM_STATIONS 16 |
| 689 |
#define TARGET_NUM_PEERS ((TARGET_NUM_STATIONS) + \ |
| 690 |
(TARGET_NUM_VDEVS)) |
| 691 |
#define TARGET_NUM_OFFLOAD_PEERS 0 |
| 692 |
#define TARGET_NUM_OFFLOAD_REORDER_BUFS 0 |
| 693 |
#define TARGET_NUM_PEER_KEYS 2 |
| 694 |
#define TARGET_NUM_TIDS ((TARGET_NUM_PEERS) * 2) |
| 695 |
#define TARGET_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) |
| 696 |
#define TARGET_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) |
| 697 |
#define TARGET_RX_TIMEOUT_LO_PRI 100 |
| 698 |
#define TARGET_RX_TIMEOUT_HI_PRI 40 |
| 699 |
|
| 700 |
#define TARGET_SCAN_MAX_PENDING_REQS 4 |
| 701 |
#define TARGET_BMISS_OFFLOAD_MAX_VDEV 3 |
| 702 |
#define TARGET_ROAM_OFFLOAD_MAX_VDEV 3 |
| 703 |
#define TARGET_ROAM_OFFLOAD_MAX_AP_PROFILES 8 |
| 704 |
#define TARGET_GTK_OFFLOAD_MAX_VDEV 3 |
| 705 |
#define TARGET_NUM_MCAST_GROUPS 0 |
| 706 |
#define TARGET_NUM_MCAST_TABLE_ELEMS 0 |
| 707 |
#define TARGET_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED |
| 708 |
#define TARGET_TX_DBG_LOG_SIZE 1024 |
| 709 |
#define TARGET_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 0 |
| 710 |
#define TARGET_VOW_CONFIG 0 |
| 711 |
#define TARGET_NUM_MSDU_DESC (1024 + 400) |
| 712 |
#define TARGET_MAX_FRAG_ENTRIES 0 |
| 713 |
|
| 714 |
/* Target specific defines for 10.X firmware */ |
| 715 |
#define TARGET_10X_NUM_VDEVS 16 |
| 716 |
#define TARGET_10X_NUM_PEER_AST 2 |
| 717 |
#define TARGET_10X_NUM_WDS_ENTRIES 32 |
| 718 |
#define TARGET_10X_DMA_BURST_SIZE 0 |
| 719 |
#define TARGET_10X_MAC_AGGR_DELIM 0 |
| 720 |
#define TARGET_10X_AST_SKID_LIMIT 128 |
| 721 |
#define TARGET_10X_NUM_STATIONS 128 |
| 722 |
#define TARGET_10X_TX_STATS_NUM_STATIONS 118 |
| 723 |
#define TARGET_10X_NUM_PEERS ((TARGET_10X_NUM_STATIONS) + \ |
| 724 |
(TARGET_10X_NUM_VDEVS)) |
| 725 |
#define TARGET_10X_TX_STATS_NUM_PEERS ((TARGET_10X_TX_STATS_NUM_STATIONS) + \ |
| 726 |
(TARGET_10X_NUM_VDEVS)) |
| 727 |
#define TARGET_10X_NUM_OFFLOAD_PEERS 0 |
| 728 |
#define TARGET_10X_NUM_OFFLOAD_REORDER_BUFS 0 |
| 729 |
#define TARGET_10X_NUM_PEER_KEYS 2 |
| 730 |
#define TARGET_10X_NUM_TIDS_MAX 256 |
| 731 |
#define TARGET_10X_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \ |
| 732 |
(TARGET_10X_NUM_PEERS) * 2) |
| 733 |
#define TARGET_10X_TX_STATS_NUM_TIDS min((TARGET_10X_NUM_TIDS_MAX), \ |
| 734 |
(TARGET_10X_TX_STATS_NUM_PEERS) * 2) |
| 735 |
#define TARGET_10X_TX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) |
| 736 |
#define TARGET_10X_RX_CHAIN_MASK (BIT(0) | BIT(1) | BIT(2)) |
| 737 |
#define TARGET_10X_RX_TIMEOUT_LO_PRI 100 |
| 738 |
#define TARGET_10X_RX_TIMEOUT_HI_PRI 40 |
| 739 |
#define TARGET_10X_SCAN_MAX_PENDING_REQS 4 |
| 740 |
#define TARGET_10X_BMISS_OFFLOAD_MAX_VDEV 2 |
| 741 |
#define TARGET_10X_ROAM_OFFLOAD_MAX_VDEV 2 |
| 742 |
#define TARGET_10X_ROAM_OFFLOAD_MAX_AP_PROFILES 8 |
| 743 |
#define TARGET_10X_GTK_OFFLOAD_MAX_VDEV 3 |
| 744 |
#define TARGET_10X_NUM_MCAST_GROUPS 0 |
| 745 |
#define TARGET_10X_NUM_MCAST_TABLE_ELEMS 0 |
| 746 |
#define TARGET_10X_MCAST2UCAST_MODE ATH10K_MCAST2UCAST_DISABLED |
| 747 |
#define TARGET_10X_TX_DBG_LOG_SIZE 1024 |
| 748 |
#define TARGET_10X_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1 |
| 749 |
#define TARGET_10X_VOW_CONFIG 0 |
| 750 |
#define TARGET_10X_NUM_MSDU_DESC (1024 + 400) |
| 751 |
#define TARGET_10X_MAX_FRAG_ENTRIES 0 |
| 752 |
|
| 753 |
/* 10.2 parameters */ |
| 754 |
#define TARGET_10_2_DMA_BURST_SIZE 0 |
| 755 |
|
| 756 |
/* Target specific defines for WMI-TLV firmware */ |
| 757 |
#define TARGET_TLV_NUM_VDEVS 4 |
| 758 |
#define TARGET_TLV_NUM_STATIONS 32 |
| 759 |
#define TARGET_TLV_NUM_PEERS 33 |
| 760 |
#define TARGET_TLV_NUM_TDLS_VDEVS 1 |
| 761 |
#define TARGET_TLV_NUM_TIDS ((TARGET_TLV_NUM_PEERS) * 2) |
| 762 |
#define TARGET_TLV_NUM_MSDU_DESC (1024 + 32) |
| 763 |
#define TARGET_TLV_NUM_MSDU_DESC_HL 1024 |
| 764 |
#define TARGET_TLV_NUM_WOW_PATTERNS 22 |
| 765 |
#define TARGET_TLV_MGMT_NUM_MSDU_DESC (50) |
| 766 |
|
| 767 |
/* Target specific defines for WMI-HL-1.0 firmware */ |
| 768 |
#define TARGET_HL_TLV_NUM_PEERS 33 |
| 769 |
#define TARGET_HL_TLV_AST_SKID_LIMIT 16 |
| 770 |
#define TARGET_HL_TLV_NUM_WDS_ENTRIES 2 |
| 771 |
|
| 772 |
/* Target specific defines for QCA9377 high latency firmware */ |
| 773 |
#define TARGET_QCA9377_HL_NUM_PEERS 15 |
| 774 |
|
| 775 |
/* Diagnostic Window */ |
| 776 |
#define CE_DIAG_PIPE 7 |
| 777 |
|
| 778 |
#define NUM_TARGET_CE_CONFIG_WLAN ar->hw_values->num_target_ce_config_wlan |
| 779 |
|
| 780 |
/* Target specific defines for 10.4 firmware */ |
| 781 |
#define TARGET_10_4_NUM_VDEVS 16 |
| 782 |
#define TARGET_10_4_NUM_STATIONS 32 |
| 783 |
#define TARGET_10_4_NUM_PEERS ((TARGET_10_4_NUM_STATIONS) + \ |
| 784 |
(TARGET_10_4_NUM_VDEVS)) |
| 785 |
#define TARGET_10_4_ACTIVE_PEERS 0 |
| 786 |
|
| 787 |
#define TARGET_10_4_NUM_QCACHE_PEERS_MAX 512 |
| 788 |
#define TARGET_10_4_QCACHE_ACTIVE_PEERS 50 |
| 789 |
#define TARGET_10_4_QCACHE_ACTIVE_PEERS_PFC 35 |
| 790 |
#define TARGET_10_4_NUM_OFFLOAD_PEERS 0 |
| 791 |
#define TARGET_10_4_NUM_OFFLOAD_REORDER_BUFFS 0 |
| 792 |
#define TARGET_10_4_NUM_PEER_KEYS 2 |
| 793 |
#define TARGET_10_4_TGT_NUM_TIDS ((TARGET_10_4_NUM_PEERS) * 2) |
| 794 |
#define TARGET_10_4_NUM_MSDU_DESC (1024 + 400) |
| 795 |
#define TARGET_10_4_NUM_MSDU_DESC_PFC 2500 |
| 796 |
#define TARGET_10_4_AST_SKID_LIMIT 32 |
| 797 |
|
| 798 |
/* 100 ms for video, best-effort, and background */ |
| 799 |
#define TARGET_10_4_RX_TIMEOUT_LO_PRI 100 |
| 800 |
|
| 801 |
/* 40 ms for voice */ |
| 802 |
#define TARGET_10_4_RX_TIMEOUT_HI_PRI 40 |
| 803 |
|
| 804 |
#define TARGET_10_4_RX_DECAP_MODE ATH10K_HW_TXRX_NATIVE_WIFI |
| 805 |
#define TARGET_10_4_SCAN_MAX_REQS 4 |
| 806 |
#define TARGET_10_4_BMISS_OFFLOAD_MAX_VDEV 3 |
| 807 |
#define TARGET_10_4_ROAM_OFFLOAD_MAX_VDEV 3 |
| 808 |
#define TARGET_10_4_ROAM_OFFLOAD_MAX_PROFILES 8 |
| 809 |
|
| 810 |
/* Note: mcast to ucast is disabled by default */ |
| 811 |
#define TARGET_10_4_NUM_MCAST_GROUPS 0 |
| 812 |
#define TARGET_10_4_NUM_MCAST_TABLE_ELEMS 0 |
| 813 |
#define TARGET_10_4_MCAST2UCAST_MODE 0 |
| 814 |
|
| 815 |
#define TARGET_10_4_TX_DBG_LOG_SIZE 1024 |
| 816 |
#define TARGET_10_4_NUM_WDS_ENTRIES 32 |
| 817 |
#define TARGET_10_4_DMA_BURST_SIZE 1 |
| 818 |
#define TARGET_10_4_MAC_AGGR_DELIM 0 |
| 819 |
#define TARGET_10_4_RX_SKIP_DEFRAG_TIMEOUT_DUP_DETECTION_CHECK 1 |
| 820 |
#define TARGET_10_4_VOW_CONFIG 0 |
| 821 |
#define TARGET_10_4_GTK_OFFLOAD_MAX_VDEV 3 |
| 822 |
#define TARGET_10_4_11AC_TX_MAX_FRAGS 2 |
| 823 |
#define TARGET_10_4_MAX_PEER_EXT_STATS 16 |
| 824 |
#define TARGET_10_4_SMART_ANT_CAP 0 |
| 825 |
#define TARGET_10_4_BK_MIN_FREE 0 |
| 826 |
#define TARGET_10_4_BE_MIN_FREE 0 |
| 827 |
#define TARGET_10_4_VI_MIN_FREE 0 |
| 828 |
#define TARGET_10_4_VO_MIN_FREE 0 |
| 829 |
#define TARGET_10_4_RX_BATCH_MODE 1 |
| 830 |
#define TARGET_10_4_THERMAL_THROTTLING_CONFIG 0 |
| 831 |
#define TARGET_10_4_ATF_CONFIG 0 |
| 832 |
#define TARGET_10_4_IPHDR_PAD_CONFIG 1 |
| 833 |
#define TARGET_10_4_QWRAP_CONFIG 0 |
| 834 |
|
| 835 |
/* TDLS config */ |
| 836 |
#define TARGET_10_4_NUM_TDLS_VDEVS 1 |
| 837 |
#define TARGET_10_4_NUM_TDLS_BUFFER_STA 1 |
| 838 |
#define TARGET_10_4_NUM_TDLS_SLEEP_STA 1 |
| 839 |
|
| 840 |
/* Maximum number of Copy Engines supported */ |
| 841 |
#define CE_COUNT_MAX 12 |
| 842 |
|
| 843 |
/* Number of Copy Engines supported */ |
| 844 |
#define CE_COUNT ar->hw_values->ce_count |
| 845 |
|
| 846 |
/* |
| 847 |
* Granted MSIs are assigned as follows: |
| 848 |
* Firmware uses the first |
| 849 |
* Remaining MSIs, if any, are used by Copy Engines |
| 850 |
* This mapping is known to both Target firmware and Host software. |
| 851 |
* It may be changed as long as Host and Target are kept in sync. |
| 852 |
*/ |
| 853 |
/* MSI for firmware (errors, etc.) */ |
| 854 |
#define MSI_ASSIGN_FW 0 |
| 855 |
|
| 856 |
/* MSIs for Copy Engines */ |
| 857 |
#define MSI_ASSIGN_CE_INITIAL 1 |
| 858 |
#define MSI_ASSIGN_CE_MAX ar->hw_values->msi_assign_ce_max |
| 859 |
|
| 860 |
/* as of IP3.7.1 */ |
| 861 |
#define RTC_STATE_V_ON ar->hw_values->rtc_state_val_on |
| 862 |
|
| 863 |
#define RTC_STATE_V_LSB 0 |
| 864 |
#define RTC_STATE_V_MASK 0x00000007 |
| 865 |
#define RTC_STATE_ADDRESS 0x0000 |
| 866 |
#define PCIE_SOC_WAKE_V_MASK 0x00000001 |
| 867 |
#define PCIE_SOC_WAKE_ADDRESS 0x0004 |
| 868 |
#define PCIE_SOC_WAKE_RESET 0x00000000 |
| 869 |
#define SOC_GLOBAL_RESET_ADDRESS 0x0008 |
| 870 |
|
| 871 |
#define RTC_SOC_BASE_ADDRESS ar->regs->rtc_soc_base_address |
| 872 |
#define RTC_WMAC_BASE_ADDRESS ar->regs->rtc_wmac_base_address |
| 873 |
#define MAC_COEX_BASE_ADDRESS 0x00006000 |
| 874 |
#define BT_COEX_BASE_ADDRESS 0x00007000 |
| 875 |
#define SOC_PCIE_BASE_ADDRESS 0x00008000 |
| 876 |
#define SOC_CORE_BASE_ADDRESS ar->regs->soc_core_base_address |
| 877 |
#define WLAN_UART_BASE_ADDRESS 0x0000c000 |
| 878 |
#define WLAN_SI_BASE_ADDRESS 0x00010000 |
| 879 |
#define WLAN_GPIO_BASE_ADDRESS 0x00014000 |
| 880 |
#define WLAN_ANALOG_INTF_BASE_ADDRESS 0x0001c000 |
| 881 |
#define WLAN_MAC_BASE_ADDRESS ar->regs->wlan_mac_base_address |
| 882 |
#define EFUSE_BASE_ADDRESS 0x00030000 |
| 883 |
#define FPGA_REG_BASE_ADDRESS 0x00039000 |
| 884 |
#define WLAN_UART2_BASE_ADDRESS 0x00054c00 |
| 885 |
#define CE_WRAPPER_BASE_ADDRESS ar->regs->ce_wrapper_base_address |
| 886 |
#define CE0_BASE_ADDRESS ar->regs->ce0_base_address |
| 887 |
#define CE1_BASE_ADDRESS ar->regs->ce1_base_address |
| 888 |
#define CE2_BASE_ADDRESS ar->regs->ce2_base_address |
| 889 |
#define CE3_BASE_ADDRESS ar->regs->ce3_base_address |
| 890 |
#define CE4_BASE_ADDRESS ar->regs->ce4_base_address |
| 891 |
#define CE5_BASE_ADDRESS ar->regs->ce5_base_address |
| 892 |
#define CE6_BASE_ADDRESS ar->regs->ce6_base_address |
| 893 |
#define CE7_BASE_ADDRESS ar->regs->ce7_base_address |
| 894 |
#define DBI_BASE_ADDRESS 0x00060000 |
| 895 |
#define WLAN_ANALOG_INTF_PCIE_BASE_ADDRESS 0x0006c000 |
| 896 |
#define PCIE_LOCAL_BASE_ADDRESS ar->regs->pcie_local_base_address |
| 897 |
|
| 898 |
#define SOC_RESET_CONTROL_ADDRESS 0x00000000 |
| 899 |
#define SOC_RESET_CONTROL_OFFSET 0x00000000 |
| 900 |
#define SOC_RESET_CONTROL_SI0_RST_MASK ar->regs->soc_reset_control_si0_rst_mask |
| 901 |
#define SOC_RESET_CONTROL_CE_RST_MASK ar->regs->soc_reset_control_ce_rst_mask |
| 902 |
#define SOC_RESET_CONTROL_CPU_WARM_RST_MASK 0x00000040 |
| 903 |
#define SOC_CPU_CLOCK_OFFSET 0x00000020 |
| 904 |
#define SOC_CPU_CLOCK_STANDARD_LSB 0 |
| 905 |
#define SOC_CPU_CLOCK_STANDARD_MASK 0x00000003 |
| 906 |
#define SOC_CLOCK_CONTROL_OFFSET 0x00000028 |
| 907 |
#define SOC_CLOCK_CONTROL_SI0_CLK_MASK 0x00000001 |
| 908 |
#define SOC_SYSTEM_SLEEP_OFFSET 0x000000c4 |
| 909 |
#define SOC_LPO_CAL_OFFSET 0x000000e0 |
| 910 |
#define SOC_LPO_CAL_ENABLE_LSB 20 |
| 911 |
#define SOC_LPO_CAL_ENABLE_MASK 0x00100000 |
| 912 |
#define SOC_LF_TIMER_CONTROL0_ADDRESS 0x00000050 |
| 913 |
#define SOC_LF_TIMER_CONTROL0_ENABLE_MASK 0x00000004 |
| 914 |
|
| 915 |
#define SOC_CHIP_ID_ADDRESS ar->regs->soc_chip_id_address |
| 916 |
#define SOC_CHIP_ID_REV_LSB 8 |
| 917 |
#define SOC_CHIP_ID_REV_MASK 0x00000f00 |
| 918 |
|
| 919 |
#define WLAN_RESET_CONTROL_COLD_RST_MASK 0x00000008 |
| 920 |
#define WLAN_RESET_CONTROL_WARM_RST_MASK 0x00000004 |
| 921 |
#define WLAN_SYSTEM_SLEEP_DISABLE_LSB 0 |
| 922 |
#define WLAN_SYSTEM_SLEEP_DISABLE_MASK 0x00000001 |
| 923 |
|
| 924 |
#define WLAN_GPIO_PIN0_ADDRESS 0x00000028 |
| 925 |
#define WLAN_GPIO_PIN0_CONFIG_LSB 11 |
| 926 |
#define WLAN_GPIO_PIN0_CONFIG_MASK 0x00007800 |
| 927 |
#define WLAN_GPIO_PIN0_PAD_PULL_LSB 5 |
| 928 |
#define WLAN_GPIO_PIN0_PAD_PULL_MASK 0x00000060 |
| 929 |
#define WLAN_GPIO_PIN1_ADDRESS 0x0000002c |
| 930 |
#define WLAN_GPIO_PIN1_CONFIG_MASK 0x00007800 |
| 931 |
#define WLAN_GPIO_PIN10_ADDRESS 0x00000050 |
| 932 |
#define WLAN_GPIO_PIN11_ADDRESS 0x00000054 |
| 933 |
#define WLAN_GPIO_PIN12_ADDRESS 0x00000058 |
| 934 |
#define WLAN_GPIO_PIN13_ADDRESS 0x0000005c |
| 935 |
|
| 936 |
#define CLOCK_GPIO_OFFSET 0xffffffff |
| 937 |
#define CLOCK_GPIO_BT_CLK_OUT_EN_LSB 0 |
| 938 |
#define CLOCK_GPIO_BT_CLK_OUT_EN_MASK 0 |
| 939 |
|
| 940 |
#define SI_CONFIG_OFFSET 0x00000000 |
| 941 |
#define SI_CONFIG_ERR_INT_LSB 19 |
| 942 |
#define SI_CONFIG_ERR_INT_MASK 0x00080000 |
| 943 |
#define SI_CONFIG_BIDIR_OD_DATA_LSB 18 |
| 944 |
#define SI_CONFIG_BIDIR_OD_DATA_MASK 0x00040000 |
| 945 |
#define SI_CONFIG_I2C_LSB 16 |
| 946 |
#define SI_CONFIG_I2C_MASK 0x00010000 |
| 947 |
#define SI_CONFIG_POS_SAMPLE_LSB 7 |
| 948 |
#define SI_CONFIG_POS_SAMPLE_MASK 0x00000080 |
| 949 |
#define SI_CONFIG_INACTIVE_DATA_LSB 5 |
| 950 |
#define SI_CONFIG_INACTIVE_DATA_MASK 0x00000020 |
| 951 |
#define SI_CONFIG_INACTIVE_CLK_LSB 4 |
| 952 |
#define SI_CONFIG_INACTIVE_CLK_MASK 0x00000010 |
| 953 |
#define SI_CONFIG_DIVIDER_LSB 0 |
| 954 |
#define SI_CONFIG_DIVIDER_MASK 0x0000000f |
| 955 |
#define SI_CS_OFFSET 0x00000004 |
| 956 |
#define SI_CS_DONE_ERR_LSB 10 |
| 957 |
#define SI_CS_DONE_ERR_MASK 0x00000400 |
| 958 |
#define SI_CS_DONE_INT_LSB 9 |
| 959 |
#define SI_CS_DONE_INT_MASK 0x00000200 |
| 960 |
#define SI_CS_START_LSB 8 |
| 961 |
#define SI_CS_START_MASK 0x00000100 |
| 962 |
#define SI_CS_RX_CNT_LSB 4 |
| 963 |
#define SI_CS_RX_CNT_MASK 0x000000f0 |
| 964 |
#define SI_CS_TX_CNT_LSB 0 |
| 965 |
#define SI_CS_TX_CNT_MASK 0x0000000f |
| 966 |
|
| 967 |
#define SI_TX_DATA0_OFFSET 0x00000008 |
| 968 |
#define SI_TX_DATA1_OFFSET 0x0000000c |
| 969 |
#define SI_RX_DATA0_OFFSET 0x00000010 |
| 970 |
#define SI_RX_DATA1_OFFSET 0x00000014 |
| 971 |
|
| 972 |
#define CORE_CTRL_CPU_INTR_MASK 0x00002000 |
| 973 |
#define CORE_CTRL_PCIE_REG_31_MASK 0x00000800 |
| 974 |
#define CORE_CTRL_ADDRESS 0x0000 |
| 975 |
#define PCIE_INTR_ENABLE_ADDRESS 0x0008 |
| 976 |
#define PCIE_INTR_CAUSE_ADDRESS 0x000c |
| 977 |
#define PCIE_INTR_CLR_ADDRESS ar->regs->pcie_intr_clr_address |
| 978 |
#define SCRATCH_3_ADDRESS ar->regs->scratch_3_address |
| 979 |
#define CPU_INTR_ADDRESS 0x0010 |
| 980 |
#define FW_RAM_CONFIG_ADDRESS 0x0018 |
| 981 |
|
| 982 |
#define CCNT_TO_MSEC(ar, x) ((x) / ar->hw_params.channel_counters_freq_hz) |
| 983 |
|
| 984 |
/* Firmware indications to the Host via SCRATCH_3 register. */ |
| 985 |
#define FW_INDICATOR_ADDRESS ar->regs->fw_indicator_address |
| 986 |
#define FW_IND_EVENT_PENDING 1 |
| 987 |
#define FW_IND_INITIALIZED 2 |
| 988 |
#define FW_IND_HOST_READY 0x80000000 |
| 989 |
|
| 990 |
/* HOST_REG interrupt from firmware */ |
| 991 |
#define PCIE_INTR_FIRMWARE_MASK ar->regs->pcie_intr_fw_mask |
| 992 |
#define PCIE_INTR_CE_MASK_ALL ar->regs->pcie_intr_ce_mask_all |
| 993 |
|
| 994 |
#define DRAM_BASE_ADDRESS 0x00400000 |
| 995 |
|
| 996 |
#define PCIE_BAR_REG_ADDRESS 0x40030 |
| 997 |
|
| 998 |
#define MISSING 0 |
| 999 |
|
| 1000 |
#define SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET |
| 1001 |
#define WLAN_SYSTEM_SLEEP_OFFSET SOC_SYSTEM_SLEEP_OFFSET |
| 1002 |
#define WLAN_RESET_CONTROL_OFFSET SOC_RESET_CONTROL_OFFSET |
| 1003 |
#define CLOCK_CONTROL_OFFSET SOC_CLOCK_CONTROL_OFFSET |
| 1004 |
#define CLOCK_CONTROL_SI0_CLK_MASK SOC_CLOCK_CONTROL_SI0_CLK_MASK |
| 1005 |
#define RESET_CONTROL_MBOX_RST_MASK MISSING |
| 1006 |
#define RESET_CONTROL_SI0_RST_MASK SOC_RESET_CONTROL_SI0_RST_MASK |
| 1007 |
#define GPIO_BASE_ADDRESS WLAN_GPIO_BASE_ADDRESS |
| 1008 |
#define GPIO_PIN0_OFFSET WLAN_GPIO_PIN0_ADDRESS |
| 1009 |
#define GPIO_PIN1_OFFSET WLAN_GPIO_PIN1_ADDRESS |
| 1010 |
#define GPIO_PIN0_CONFIG_LSB WLAN_GPIO_PIN0_CONFIG_LSB |
| 1011 |
#define GPIO_PIN0_CONFIG_MASK WLAN_GPIO_PIN0_CONFIG_MASK |
| 1012 |
#define GPIO_PIN0_PAD_PULL_LSB WLAN_GPIO_PIN0_PAD_PULL_LSB |
| 1013 |
#define GPIO_PIN0_PAD_PULL_MASK WLAN_GPIO_PIN0_PAD_PULL_MASK |
| 1014 |
#define GPIO_PIN1_CONFIG_MASK WLAN_GPIO_PIN1_CONFIG_MASK |
| 1015 |
#define SI_BASE_ADDRESS WLAN_SI_BASE_ADDRESS |
| 1016 |
#define SCRATCH_BASE_ADDRESS SOC_CORE_BASE_ADDRESS |
| 1017 |
#define LOCAL_SCRATCH_OFFSET 0x18 |
| 1018 |
#define CPU_CLOCK_OFFSET SOC_CPU_CLOCK_OFFSET |
| 1019 |
#define LPO_CAL_OFFSET SOC_LPO_CAL_OFFSET |
| 1020 |
#define GPIO_PIN10_OFFSET WLAN_GPIO_PIN10_ADDRESS |
| 1021 |
#define GPIO_PIN11_OFFSET WLAN_GPIO_PIN11_ADDRESS |
| 1022 |
#define GPIO_PIN12_OFFSET WLAN_GPIO_PIN12_ADDRESS |
| 1023 |
#define GPIO_PIN13_OFFSET WLAN_GPIO_PIN13_ADDRESS |
| 1024 |
#define CPU_CLOCK_STANDARD_LSB SOC_CPU_CLOCK_STANDARD_LSB |
| 1025 |
#define CPU_CLOCK_STANDARD_MASK SOC_CPU_CLOCK_STANDARD_MASK |
| 1026 |
#define LPO_CAL_ENABLE_LSB SOC_LPO_CAL_ENABLE_LSB |
| 1027 |
#define LPO_CAL_ENABLE_MASK SOC_LPO_CAL_ENABLE_MASK |
| 1028 |
#define ANALOG_INTF_BASE_ADDRESS WLAN_ANALOG_INTF_BASE_ADDRESS |
| 1029 |
#define MBOX_BASE_ADDRESS MISSING |
| 1030 |
#define INT_STATUS_ENABLE_ERROR_LSB MISSING |
| 1031 |
#define INT_STATUS_ENABLE_ERROR_MASK MISSING |
| 1032 |
#define INT_STATUS_ENABLE_CPU_LSB MISSING |
| 1033 |
#define INT_STATUS_ENABLE_CPU_MASK MISSING |
| 1034 |
#define INT_STATUS_ENABLE_COUNTER_LSB MISSING |
| 1035 |
#define INT_STATUS_ENABLE_COUNTER_MASK MISSING |
| 1036 |
#define INT_STATUS_ENABLE_MBOX_DATA_LSB MISSING |
| 1037 |
#define INT_STATUS_ENABLE_MBOX_DATA_MASK MISSING |
| 1038 |
#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB MISSING |
| 1039 |
#define ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK MISSING |
| 1040 |
#define ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB MISSING |
| 1041 |
#define ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK MISSING |
| 1042 |
#define COUNTER_INT_STATUS_ENABLE_BIT_LSB MISSING |
| 1043 |
#define COUNTER_INT_STATUS_ENABLE_BIT_MASK MISSING |
| 1044 |
#define INT_STATUS_ENABLE_ADDRESS MISSING |
| 1045 |
#define CPU_INT_STATUS_ENABLE_BIT_LSB MISSING |
| 1046 |
#define CPU_INT_STATUS_ENABLE_BIT_MASK MISSING |
| 1047 |
#define HOST_INT_STATUS_ADDRESS MISSING |
| 1048 |
#define CPU_INT_STATUS_ADDRESS MISSING |
| 1049 |
#define ERROR_INT_STATUS_ADDRESS MISSING |
| 1050 |
#define ERROR_INT_STATUS_WAKEUP_MASK MISSING |
| 1051 |
#define ERROR_INT_STATUS_WAKEUP_LSB MISSING |
| 1052 |
#define ERROR_INT_STATUS_RX_UNDERFLOW_MASK MISSING |
| 1053 |
#define ERROR_INT_STATUS_RX_UNDERFLOW_LSB MISSING |
| 1054 |
#define ERROR_INT_STATUS_TX_OVERFLOW_MASK MISSING |
| 1055 |
#define ERROR_INT_STATUS_TX_OVERFLOW_LSB MISSING |
| 1056 |
#define COUNT_DEC_ADDRESS MISSING |
| 1057 |
#define HOST_INT_STATUS_CPU_MASK MISSING |
| 1058 |
#define HOST_INT_STATUS_CPU_LSB MISSING |
| 1059 |
#define HOST_INT_STATUS_ERROR_MASK MISSING |
| 1060 |
#define HOST_INT_STATUS_ERROR_LSB MISSING |
| 1061 |
#define HOST_INT_STATUS_COUNTER_MASK MISSING |
| 1062 |
#define HOST_INT_STATUS_COUNTER_LSB MISSING |
| 1063 |
#define RX_LOOKAHEAD_VALID_ADDRESS MISSING |
| 1064 |
#define WINDOW_DATA_ADDRESS MISSING |
| 1065 |
#define WINDOW_READ_ADDR_ADDRESS MISSING |
| 1066 |
#define WINDOW_WRITE_ADDR_ADDRESS MISSING |
| 1067 |
|
| 1068 |
#define QCA9887_1_0_I2C_SDA_GPIO_PIN 5 |
| 1069 |
#define QCA9887_1_0_I2C_SDA_PIN_CONFIG 3 |
| 1070 |
#define QCA9887_1_0_SI_CLK_GPIO_PIN 17 |
| 1071 |
#define QCA9887_1_0_SI_CLK_PIN_CONFIG 3 |
| 1072 |
#define QCA9887_1_0_GPIO_ENABLE_W1TS_LOW_ADDRESS 0x00000010 |
| 1073 |
|
| 1074 |
#define QCA9887_EEPROM_SELECT_READ 0xa10000a0 |
| 1075 |
#define QCA9887_EEPROM_ADDR_HI_MASK 0x0000ff00 |
| 1076 |
#define QCA9887_EEPROM_ADDR_HI_LSB 8 |
| 1077 |
#define QCA9887_EEPROM_ADDR_LO_MASK 0x00ff0000 |
| 1078 |
#define QCA9887_EEPROM_ADDR_LO_LSB 16 |
| 1079 |
|
| 1080 |
#define MBOX_RESET_CONTROL_ADDRESS 0x00000000 |
| 1081 |
#define MBOX_HOST_INT_STATUS_ADDRESS 0x00000800 |
| 1082 |
#define MBOX_HOST_INT_STATUS_ERROR_LSB 7 |
| 1083 |
#define MBOX_HOST_INT_STATUS_ERROR_MASK 0x00000080 |
| 1084 |
#define MBOX_HOST_INT_STATUS_CPU_LSB 6 |
| 1085 |
#define MBOX_HOST_INT_STATUS_CPU_MASK 0x00000040 |
| 1086 |
#define MBOX_HOST_INT_STATUS_COUNTER_LSB 4 |
| 1087 |
#define MBOX_HOST_INT_STATUS_COUNTER_MASK 0x00000010 |
| 1088 |
#define MBOX_CPU_INT_STATUS_ADDRESS 0x00000801 |
| 1089 |
#define MBOX_ERROR_INT_STATUS_ADDRESS 0x00000802 |
| 1090 |
#define MBOX_ERROR_INT_STATUS_WAKEUP_LSB 2 |
| 1091 |
#define MBOX_ERROR_INT_STATUS_WAKEUP_MASK 0x00000004 |
| 1092 |
#define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_LSB 1 |
| 1093 |
#define MBOX_ERROR_INT_STATUS_RX_UNDERFLOW_MASK 0x00000002 |
| 1094 |
#define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_LSB 0 |
| 1095 |
#define MBOX_ERROR_INT_STATUS_TX_OVERFLOW_MASK 0x00000001 |
| 1096 |
#define MBOX_COUNTER_INT_STATUS_ADDRESS 0x00000803 |
| 1097 |
#define MBOX_COUNTER_INT_STATUS_COUNTER_LSB 0 |
| 1098 |
#define MBOX_COUNTER_INT_STATUS_COUNTER_MASK 0x000000ff |
| 1099 |
#define MBOX_RX_LOOKAHEAD_VALID_ADDRESS 0x00000805 |
| 1100 |
#define MBOX_INT_STATUS_ENABLE_ADDRESS 0x00000828 |
| 1101 |
#define MBOX_INT_STATUS_ENABLE_ERROR_LSB 7 |
| 1102 |
#define MBOX_INT_STATUS_ENABLE_ERROR_MASK 0x00000080 |
| 1103 |
#define MBOX_INT_STATUS_ENABLE_CPU_LSB 6 |
| 1104 |
#define MBOX_INT_STATUS_ENABLE_CPU_MASK 0x00000040 |
| 1105 |
#define MBOX_INT_STATUS_ENABLE_INT_LSB 5 |
| 1106 |
#define MBOX_INT_STATUS_ENABLE_INT_MASK 0x00000020 |
| 1107 |
#define MBOX_INT_STATUS_ENABLE_COUNTER_LSB 4 |
| 1108 |
#define MBOX_INT_STATUS_ENABLE_COUNTER_MASK 0x00000010 |
| 1109 |
#define MBOX_INT_STATUS_ENABLE_MBOX_DATA_LSB 0 |
| 1110 |
#define MBOX_INT_STATUS_ENABLE_MBOX_DATA_MASK 0x0000000f |
| 1111 |
#define MBOX_CPU_INT_STATUS_ENABLE_ADDRESS 0x00000819 |
| 1112 |
#define MBOX_CPU_INT_STATUS_ENABLE_BIT_LSB 0 |
| 1113 |
#define MBOX_CPU_INT_STATUS_ENABLE_BIT_MASK 0x000000ff |
| 1114 |
#define MBOX_CPU_STATUS_ENABLE_ASSERT_MASK 0x00000001 |
| 1115 |
#define MBOX_ERROR_STATUS_ENABLE_ADDRESS 0x0000081a |
| 1116 |
#define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_LSB 1 |
| 1117 |
#define MBOX_ERROR_STATUS_ENABLE_RX_UNDERFLOW_MASK 0x00000002 |
| 1118 |
#define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_LSB 0 |
| 1119 |
#define MBOX_ERROR_STATUS_ENABLE_TX_OVERFLOW_MASK 0x00000001 |
| 1120 |
#define MBOX_COUNTER_INT_STATUS_ENABLE_ADDRESS 0x0000081b |
| 1121 |
#define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_LSB 0 |
| 1122 |
#define MBOX_COUNTER_INT_STATUS_ENABLE_BIT_MASK 0x000000ff |
| 1123 |
#define MBOX_COUNT_ADDRESS 0x00000820 |
| 1124 |
#define MBOX_COUNT_DEC_ADDRESS 0x00000840 |
| 1125 |
#define MBOX_WINDOW_DATA_ADDRESS 0x00000874 |
| 1126 |
#define MBOX_WINDOW_WRITE_ADDR_ADDRESS 0x00000878 |
| 1127 |
#define MBOX_WINDOW_READ_ADDR_ADDRESS 0x0000087c |
| 1128 |
#define MBOX_CPU_DBG_SEL_ADDRESS 0x00000883 |
| 1129 |
#define MBOX_CPU_DBG_ADDRESS 0x00000884 |
| 1130 |
#define MBOX_RTC_BASE_ADDRESS 0x00000000 |
| 1131 |
#define MBOX_GPIO_BASE_ADDRESS 0x00005000 |
| 1132 |
#define MBOX_MBOX_BASE_ADDRESS 0x00008000 |
| 1133 |
|
| 1134 |
#define RTC_STATE_V_GET(x) (((x) & RTC_STATE_V_MASK) >> RTC_STATE_V_LSB) |
| 1135 |
|
| 1136 |
/* Register definitions for first generation ath10k cards. These cards include |
| 1137 |
* a mac which has a register allocation similar to ath9k and at least some |
| 1138 |
* registers including the ones relevant for modifying the coverage class are |
| 1139 |
* identical to the ath9k definitions. |
| 1140 |
* These registers are usually managed by the ath10k firmware. However by |
| 1141 |
* overriding them it is possible to support coverage class modifications. |
| 1142 |
*/ |
| 1143 |
#define WAVE1_PCU_ACK_CTS_TIMEOUT 0x8014 |
| 1144 |
#define WAVE1_PCU_ACK_CTS_TIMEOUT_MAX 0x00003FFF |
| 1145 |
#define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_MASK 0x00003FFF |
| 1146 |
#define WAVE1_PCU_ACK_CTS_TIMEOUT_ACK_LSB 0 |
| 1147 |
#define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_MASK 0x3FFF0000 |
| 1148 |
#define WAVE1_PCU_ACK_CTS_TIMEOUT_CTS_LSB 16 |
| 1149 |
|
| 1150 |
#define WAVE1_PCU_GBL_IFS_SLOT 0x1070 |
| 1151 |
#define WAVE1_PCU_GBL_IFS_SLOT_MASK 0x0000FFFF |
| 1152 |
#define WAVE1_PCU_GBL_IFS_SLOT_MAX 0x0000FFFF |
| 1153 |
#define WAVE1_PCU_GBL_IFS_SLOT_LSB 0 |
| 1154 |
#define WAVE1_PCU_GBL_IFS_SLOT_RESV0 0xFFFF0000 |
| 1155 |
|
| 1156 |
#define WAVE1_PHYCLK 0x801C |
| 1157 |
#define WAVE1_PHYCLK_USEC_MASK 0x0000007F |
| 1158 |
#define WAVE1_PHYCLK_USEC_LSB 0 |
| 1159 |
|
| 1160 |
/* qca6174 PLL offset/mask */ |
| 1161 |
#define SOC_CORE_CLK_CTRL_OFFSET 0x00000114 |
| 1162 |
#define SOC_CORE_CLK_CTRL_DIV_LSB 0 |
| 1163 |
#define SOC_CORE_CLK_CTRL_DIV_MASK 0x00000007 |
| 1164 |
|
| 1165 |
#define EFUSE_OFFSET 0x0000032c |
| 1166 |
#define EFUSE_XTAL_SEL_LSB 8 |
| 1167 |
#define EFUSE_XTAL_SEL_MASK 0x00000700 |
| 1168 |
|
| 1169 |
#define BB_PLL_CONFIG_OFFSET 0x000002f4 |
| 1170 |
#define BB_PLL_CONFIG_FRAC_LSB 0 |
| 1171 |
#define BB_PLL_CONFIG_FRAC_MASK 0x0003ffff |
| 1172 |
#define BB_PLL_CONFIG_OUTDIV_LSB 18 |
| 1173 |
#define BB_PLL_CONFIG_OUTDIV_MASK 0x001c0000 |
| 1174 |
|
| 1175 |
#define WLAN_PLL_SETTLE_OFFSET 0x0018 |
| 1176 |
#define WLAN_PLL_SETTLE_TIME_LSB 0 |
| 1177 |
#define WLAN_PLL_SETTLE_TIME_MASK 0x000007ff |
| 1178 |
|
| 1179 |
#define WLAN_PLL_CONTROL_OFFSET 0x0014 |
| 1180 |
#define WLAN_PLL_CONTROL_DIV_LSB 0 |
| 1181 |
#define WLAN_PLL_CONTROL_DIV_MASK 0x000003ff |
| 1182 |
#define WLAN_PLL_CONTROL_REFDIV_LSB 10 |
| 1183 |
#define WLAN_PLL_CONTROL_REFDIV_MASK 0x00003c00 |
| 1184 |
#define WLAN_PLL_CONTROL_BYPASS_LSB 16 |
| 1185 |
#define WLAN_PLL_CONTROL_BYPASS_MASK 0x00010000 |
| 1186 |
#define WLAN_PLL_CONTROL_NOPWD_LSB 18 |
| 1187 |
#define WLAN_PLL_CONTROL_NOPWD_MASK 0x00040000 |
| 1188 |
|
| 1189 |
#define RTC_SYNC_STATUS_OFFSET 0x0244 |
| 1190 |
#define RTC_SYNC_STATUS_PLL_CHANGING_LSB 5 |
| 1191 |
#define RTC_SYNC_STATUS_PLL_CHANGING_MASK 0x00000020 |
| 1192 |
/* qca6174 PLL offset/mask end */ |
| 1193 |
|
| 1194 |
/* CPU_ADDR_MSB is a register, bit[3:0] is to specify which memory |
| 1195 |
* region is accessed. The memory region size is 1M. |
| 1196 |
* If host wants to access 0xX12345 at target, then CPU_ADDR_MSB[3:0] |
| 1197 |
* is 0xX. |
| 1198 |
* The following MACROs are defined to get the 0xX and the size limit. |
| 1199 |
*/ |
| 1200 |
#define CPU_ADDR_MSB_REGION_MASK GENMASK(23, 20) |
| 1201 |
#define CPU_ADDR_MSB_REGION_VAL(X) FIELD_GET(CPU_ADDR_MSB_REGION_MASK, X) |
| 1202 |
#define REGION_ACCESS_SIZE_LIMIT 0x100000 |
| 1203 |
#define REGION_ACCESS_SIZE_MASK (REGION_ACCESS_SIZE_LIMIT - 1) |
| 1204 |
|
| 1205 |
#endif /* _HW_H_ */ |