| 1 |
// SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| 2 |
|
| 3 |
/* |
| 4 |
* Copyright (C) 2018 Zodiac Inflight Innovations |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
#include "vf610.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "ZII VF610 CFU1 Board"; |
| 12 |
compatible = "zii,vf610cfu1", "zii,vf610dev", "fsl,vf610"; |
| 13 |
|
| 14 |
chosen { |
| 15 |
stdout-path = &uart0; |
| 16 |
}; |
| 17 |
|
| 18 |
memory@80000000 { |
| 19 |
device_type = "memory"; |
| 20 |
reg = <0x80000000 0x20000000>; |
| 21 |
}; |
| 22 |
|
| 23 |
gpio-leds { |
| 24 |
compatible = "gpio-leds"; |
| 25 |
pinctrl-0 = <&pinctrl_leds_debug>; |
| 26 |
pinctrl-names = "default"; |
| 27 |
|
| 28 |
led-debug { |
| 29 |
label = "zii:green:debug1"; |
| 30 |
gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>; |
| 31 |
linux,default-trigger = "heartbeat"; |
| 32 |
}; |
| 33 |
|
| 34 |
led-fail { |
| 35 |
label = "zii:red:fail"; |
| 36 |
gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; |
| 37 |
default-state = "off"; |
| 38 |
}; |
| 39 |
|
| 40 |
led-status { |
| 41 |
label = "zii:green:status"; |
| 42 |
gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; |
| 43 |
default-state = "off"; |
| 44 |
}; |
| 45 |
|
| 46 |
led-debug-a { |
| 47 |
label = "zii:green:debug_a"; |
| 48 |
gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; |
| 49 |
default-state = "off"; |
| 50 |
}; |
| 51 |
|
| 52 |
led-debug-b { |
| 53 |
label = "zii:green:debug_b"; |
| 54 |
gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>; |
| 55 |
default-state = "off"; |
| 56 |
}; |
| 57 |
}; |
| 58 |
|
| 59 |
reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu { |
| 60 |
compatible = "regulator-fixed"; |
| 61 |
regulator-name = "vcc_3v3_mcu"; |
| 62 |
regulator-min-microvolt = <3300000>; |
| 63 |
regulator-max-microvolt = <3300000>; |
| 64 |
}; |
| 65 |
|
| 66 |
sff: sfp { |
| 67 |
compatible = "sff,sff"; |
| 68 |
pinctrl-0 = <&pinctrl_optical>; |
| 69 |
pinctrl-names = "default"; |
| 70 |
i2c-bus = <&i2c0>; |
| 71 |
los-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; |
| 72 |
tx-disable-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; |
| 73 |
}; |
| 74 |
|
| 75 |
supply-voltage-monitor { |
| 76 |
compatible = "iio-hwmon"; |
| 77 |
io-channels = <&adc0 8>, /* 28VDC_IN */ |
| 78 |
<&adc0 9>, /* +3.3V */ |
| 79 |
<&adc1 8>, /* VCC_1V5 */ |
| 80 |
<&adc1 9>; /* VCC_1V2 */ |
| 81 |
}; |
| 82 |
}; |
| 83 |
|
| 84 |
&adc0 { |
| 85 |
vref-supply = <®_vcc_3v3_mcu>; |
| 86 |
status = "okay"; |
| 87 |
}; |
| 88 |
|
| 89 |
&adc1 { |
| 90 |
vref-supply = <®_vcc_3v3_mcu>; |
| 91 |
status = "okay"; |
| 92 |
}; |
| 93 |
|
| 94 |
&dspi1 { |
| 95 |
bus-num = <1>; |
| 96 |
pinctrl-names = "default"; |
| 97 |
pinctrl-0 = <&pinctrl_dspi1>; |
| 98 |
/* |
| 99 |
* Some CFU1s come with SPI-NOR chip DNPed, so we leave this |
| 100 |
* node disabled by default and rely on bootloader to enable |
| 101 |
* it when appropriate. |
| 102 |
*/ |
| 103 |
status = "disabled"; |
| 104 |
|
| 105 |
flash@0 { |
| 106 |
#address-cells = <1>; |
| 107 |
#size-cells = <1>; |
| 108 |
compatible = "m25p128", "jedec,spi-nor"; |
| 109 |
reg = <0>; |
| 110 |
spi-max-frequency = <50000000>; |
| 111 |
|
| 112 |
partition@0 { |
| 113 |
label = "m25p128-0"; |
| 114 |
reg = <0x0 0x01000000>; |
| 115 |
}; |
| 116 |
}; |
| 117 |
}; |
| 118 |
|
| 119 |
&edma0 { |
| 120 |
status = "okay"; |
| 121 |
}; |
| 122 |
|
| 123 |
&edma1 { |
| 124 |
status = "okay"; |
| 125 |
}; |
| 126 |
|
| 127 |
&esdhc0 { |
| 128 |
pinctrl-names = "default"; |
| 129 |
pinctrl-0 = <&pinctrl_esdhc0>; |
| 130 |
bus-width = <8>; |
| 131 |
non-removable; |
| 132 |
no-1-8-v; |
| 133 |
keep-power-in-suspend; |
| 134 |
no-sdio; |
| 135 |
no-sd; |
| 136 |
status = "okay"; |
| 137 |
}; |
| 138 |
|
| 139 |
&esdhc1 { |
| 140 |
pinctrl-names = "default"; |
| 141 |
pinctrl-0 = <&pinctrl_esdhc1>; |
| 142 |
bus-width = <4>; |
| 143 |
no-sdio; |
| 144 |
status = "okay"; |
| 145 |
}; |
| 146 |
|
| 147 |
&fec1 { |
| 148 |
phy-mode = "rmii"; |
| 149 |
pinctrl-names = "default"; |
| 150 |
pinctrl-0 = <&pinctrl_fec1>; |
| 151 |
status = "okay"; |
| 152 |
|
| 153 |
fixed-link { |
| 154 |
speed = <100>; |
| 155 |
full-duplex; |
| 156 |
}; |
| 157 |
|
| 158 |
mdio1: mdio { |
| 159 |
#address-cells = <1>; |
| 160 |
#size-cells = <0>; |
| 161 |
clock-frequency = <12500000>; |
| 162 |
suppress-preamble; |
| 163 |
status = "okay"; |
| 164 |
|
| 165 |
switch0: ethernet-switch@0 { |
| 166 |
compatible = "marvell,mv88e6085"; |
| 167 |
pinctrl-names = "default"; |
| 168 |
pinctrl-0 = <&pinctrl_switch>; |
| 169 |
reg = <0>; |
| 170 |
eeprom-length = <512>; |
| 171 |
interrupt-parent = <&gpio3>; |
| 172 |
interrupts = <2 IRQ_TYPE_LEVEL_LOW>; |
| 173 |
interrupt-controller; |
| 174 |
#interrupt-cells = <2>; |
| 175 |
|
| 176 |
ethernet-ports { |
| 177 |
#address-cells = <1>; |
| 178 |
#size-cells = <0>; |
| 179 |
|
| 180 |
ethernet-port@0 { |
| 181 |
reg = <0>; |
| 182 |
label = "eth_cu_1000_1"; |
| 183 |
}; |
| 184 |
|
| 185 |
ethernet-port@1 { |
| 186 |
reg = <1>; |
| 187 |
label = "eth_cu_1000_2"; |
| 188 |
}; |
| 189 |
|
| 190 |
ethernet-port@2 { |
| 191 |
reg = <2>; |
| 192 |
label = "eth_cu_1000_3"; |
| 193 |
}; |
| 194 |
|
| 195 |
ethernet-port@5 { |
| 196 |
reg = <5>; |
| 197 |
label = "eth_fc_1000_1"; |
| 198 |
phy-mode = "1000base-x"; |
| 199 |
managed = "in-band-status"; |
| 200 |
sfp = <&sff>; |
| 201 |
}; |
| 202 |
|
| 203 |
ethernet-port@6 { |
| 204 |
reg = <6>; |
| 205 |
phy-mode = "rmii"; |
| 206 |
ethernet = <&fec1>; |
| 207 |
|
| 208 |
fixed-link { |
| 209 |
speed = <100>; |
| 210 |
full-duplex; |
| 211 |
}; |
| 212 |
}; |
| 213 |
}; |
| 214 |
}; |
| 215 |
}; |
| 216 |
}; |
| 217 |
|
| 218 |
&i2c0 { |
| 219 |
clock-frequency = <100000>; |
| 220 |
pinctrl-names = "default"; |
| 221 |
pinctrl-0 = <&pinctrl_i2c0>; |
| 222 |
status = "okay"; |
| 223 |
|
| 224 |
io-expander@22 { |
| 225 |
compatible = "nxp,pca9554"; |
| 226 |
reg = <0x22>; |
| 227 |
gpio-controller; |
| 228 |
#gpio-cells = <2>; |
| 229 |
}; |
| 230 |
|
| 231 |
lm75@48 { |
| 232 |
compatible = "national,lm75"; |
| 233 |
reg = <0x48>; |
| 234 |
}; |
| 235 |
|
| 236 |
eeprom@52 { |
| 237 |
compatible = "atmel,24c04"; |
| 238 |
reg = <0x52>; |
| 239 |
label = "nvm"; |
| 240 |
}; |
| 241 |
|
| 242 |
eeprom@54 { |
| 243 |
compatible = "atmel,24c04"; |
| 244 |
reg = <0x54>; |
| 245 |
label = "nameplate"; |
| 246 |
}; |
| 247 |
}; |
| 248 |
|
| 249 |
&i2c1 { |
| 250 |
clock-frequency = <100000>; |
| 251 |
pinctrl-names = "default"; |
| 252 |
pinctrl-0 = <&pinctrl_i2c1>; |
| 253 |
status = "okay"; |
| 254 |
|
| 255 |
watchdog@38 { |
| 256 |
compatible = "zii,rave-wdt"; |
| 257 |
reg = <0x38>; |
| 258 |
}; |
| 259 |
}; |
| 260 |
|
| 261 |
&snvsrtc { |
| 262 |
status = "disabled"; |
| 263 |
}; |
| 264 |
|
| 265 |
&uart0 { |
| 266 |
pinctrl-names = "default"; |
| 267 |
pinctrl-0 = <&pinctrl_uart0>; |
| 268 |
status = "okay"; |
| 269 |
}; |
| 270 |
|
| 271 |
&iomuxc { |
| 272 |
pinctrl_dspi1: dspi1grp { |
| 273 |
fsl,pins = < |
| 274 |
VF610_PAD_PTD5__DSPI1_CS0 0x1182 |
| 275 |
VF610_PAD_PTC6__DSPI1_SIN 0x1181 |
| 276 |
VF610_PAD_PTC7__DSPI1_SOUT 0x1182 |
| 277 |
VF610_PAD_PTC8__DSPI1_SCK 0x1182 |
| 278 |
>; |
| 279 |
}; |
| 280 |
|
| 281 |
pinctrl_esdhc0: esdhc0grp { |
| 282 |
fsl,pins = < |
| 283 |
VF610_PAD_PTC0__ESDHC0_CLK 0x31ef |
| 284 |
VF610_PAD_PTC1__ESDHC0_CMD 0x31ef |
| 285 |
VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef |
| 286 |
VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef |
| 287 |
VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef |
| 288 |
VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef |
| 289 |
VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef |
| 290 |
VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef |
| 291 |
VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef |
| 292 |
VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef |
| 293 |
>; |
| 294 |
}; |
| 295 |
|
| 296 |
pinctrl_esdhc1: esdhc1grp { |
| 297 |
fsl,pins = < |
| 298 |
VF610_PAD_PTA24__ESDHC1_CLK 0x31ef |
| 299 |
VF610_PAD_PTA25__ESDHC1_CMD 0x31ef |
| 300 |
VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef |
| 301 |
VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef |
| 302 |
VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef |
| 303 |
VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef |
| 304 |
>; |
| 305 |
}; |
| 306 |
|
| 307 |
pinctrl_fec1: fec1grp { |
| 308 |
fsl,pins = < |
| 309 |
VF610_PAD_PTA6__RMII_CLKIN 0x30d1 |
| 310 |
VF610_PAD_PTC9__ENET_RMII1_MDC 0x30fe |
| 311 |
VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3 |
| 312 |
VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1 |
| 313 |
VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1 |
| 314 |
VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1 |
| 315 |
VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1 |
| 316 |
VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2 |
| 317 |
VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2 |
| 318 |
VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2 |
| 319 |
>; |
| 320 |
}; |
| 321 |
|
| 322 |
pinctrl_i2c0: i2c0grp { |
| 323 |
fsl,pins = < |
| 324 |
VF610_PAD_PTB14__I2C0_SCL 0x37ff |
| 325 |
VF610_PAD_PTB15__I2C0_SDA 0x37ff |
| 326 |
>; |
| 327 |
}; |
| 328 |
|
| 329 |
pinctrl_i2c1: i2c1grp { |
| 330 |
fsl,pins = < |
| 331 |
VF610_PAD_PTB16__I2C1_SCL 0x37ff |
| 332 |
VF610_PAD_PTB17__I2C1_SDA 0x37ff |
| 333 |
>; |
| 334 |
}; |
| 335 |
|
| 336 |
pinctrl_leds_debug: pinctrl-leds-debuggrp { |
| 337 |
fsl,pins = < |
| 338 |
VF610_PAD_PTD3__GPIO_82 0x31c2 |
| 339 |
VF610_PAD_PTE3__GPIO_108 0x31c2 |
| 340 |
VF610_PAD_PTE4__GPIO_109 0x31c2 |
| 341 |
VF610_PAD_PTE5__GPIO_110 0x31c2 |
| 342 |
VF610_PAD_PTE6__GPIO_111 0x31c2 |
| 343 |
>; |
| 344 |
}; |
| 345 |
|
| 346 |
pinctrl_optical: optical-grp { |
| 347 |
fsl,pins = < |
| 348 |
/* SFF SD input */ |
| 349 |
VF610_PAD_PTE27__GPIO_132 0x3061 |
| 350 |
|
| 351 |
/* SFF Transmit disable output */ |
| 352 |
VF610_PAD_PTE13__GPIO_118 0x3043 |
| 353 |
>; |
| 354 |
}; |
| 355 |
|
| 356 |
pinctrl_switch: switch-grp { |
| 357 |
fsl,pins = < |
| 358 |
VF610_PAD_PTB28__GPIO_98 0x3061 |
| 359 |
>; |
| 360 |
}; |
| 361 |
|
| 362 |
pinctrl_uart0: uart0grp { |
| 363 |
fsl,pins = < |
| 364 |
VF610_PAD_PTB10__UART0_TX 0x21a2 |
| 365 |
VF610_PAD_PTB11__UART0_RX 0x21a1 |
| 366 |
>; |
| 367 |
}; |
| 368 |
}; |