| 1 |
// SPDX-License-Identifier: GPL-2.0 |
| 2 |
/* Copyright 2016-2018 NXP Semiconductors |
| 3 |
* Copyright 2019 Vladimir Oltean <[email protected]> |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
#include "ls1021a.dtsi" |
| 8 |
|
| 9 |
/ { |
| 10 |
model = "NXP LS1021A-TSN Board"; |
| 11 |
compatible = "fsl,ls1021a-tsn", "fsl,ls1021a"; |
| 12 |
|
| 13 |
sys_mclk: clock-mclk { |
| 14 |
compatible = "fixed-clock"; |
| 15 |
#clock-cells = <0>; |
| 16 |
clock-frequency = <24576000>; |
| 17 |
}; |
| 18 |
|
| 19 |
reg_vdda_codec: regulator-3V3 { |
| 20 |
compatible = "regulator-fixed"; |
| 21 |
regulator-name = "3P3V"; |
| 22 |
regulator-min-microvolt = <3300000>; |
| 23 |
regulator-max-microvolt = <3300000>; |
| 24 |
regulator-always-on; |
| 25 |
}; |
| 26 |
|
| 27 |
reg_vddio_codec: regulator-2V5 { |
| 28 |
compatible = "regulator-fixed"; |
| 29 |
regulator-name = "2P5V"; |
| 30 |
regulator-min-microvolt = <2500000>; |
| 31 |
regulator-max-microvolt = <2500000>; |
| 32 |
regulator-always-on; |
| 33 |
}; |
| 34 |
}; |
| 35 |
|
| 36 |
&dspi0 { |
| 37 |
bus-num = <0>; |
| 38 |
status = "okay"; |
| 39 |
|
| 40 |
/* ADG704BRMZ 1:4 SPI mux/demux */ |
| 41 |
sja1105: ethernet-switch@1 { |
| 42 |
reg = <0x1>; |
| 43 |
compatible = "nxp,sja1105t"; |
| 44 |
/* 12 MHz */ |
| 45 |
spi-max-frequency = <12000000>; |
| 46 |
/* Sample data on trailing clock edge */ |
| 47 |
spi-cpha; |
| 48 |
/* SPI controller settings for SJA1105 timing requirements */ |
| 49 |
fsl,spi-cs-sck-delay = <1000>; |
| 50 |
fsl,spi-sck-cs-delay = <1000>; |
| 51 |
|
| 52 |
ports { |
| 53 |
#address-cells = <1>; |
| 54 |
#size-cells = <0>; |
| 55 |
|
| 56 |
port@0 { |
| 57 |
/* ETH5 written on chassis */ |
| 58 |
label = "swp5"; |
| 59 |
phy-handle = <&rgmii_phy6>; |
| 60 |
phy-mode = "rgmii-id"; |
| 61 |
reg = <0>; |
| 62 |
}; |
| 63 |
|
| 64 |
port@1 { |
| 65 |
/* ETH2 written on chassis */ |
| 66 |
label = "swp2"; |
| 67 |
phy-handle = <&rgmii_phy3>; |
| 68 |
phy-mode = "rgmii-id"; |
| 69 |
reg = <1>; |
| 70 |
}; |
| 71 |
|
| 72 |
port@2 { |
| 73 |
/* ETH3 written on chassis */ |
| 74 |
label = "swp3"; |
| 75 |
phy-handle = <&rgmii_phy4>; |
| 76 |
phy-mode = "rgmii-id"; |
| 77 |
reg = <2>; |
| 78 |
}; |
| 79 |
|
| 80 |
port@3 { |
| 81 |
/* ETH4 written on chassis */ |
| 82 |
label = "swp4"; |
| 83 |
phy-handle = <&rgmii_phy5>; |
| 84 |
phy-mode = "rgmii-id"; |
| 85 |
reg = <3>; |
| 86 |
}; |
| 87 |
|
| 88 |
port@4 { |
| 89 |
/* Internal port connected to eth2 */ |
| 90 |
ethernet = <&enet2>; |
| 91 |
phy-mode = "rgmii"; |
| 92 |
rx-internal-delay-ps = <0>; |
| 93 |
tx-internal-delay-ps = <0>; |
| 94 |
reg = <4>; |
| 95 |
|
| 96 |
fixed-link { |
| 97 |
speed = <1000>; |
| 98 |
full-duplex; |
| 99 |
}; |
| 100 |
}; |
| 101 |
}; |
| 102 |
}; |
| 103 |
}; |
| 104 |
|
| 105 |
&enet0 { |
| 106 |
tbi-handle = <&tbi0>; |
| 107 |
phy-handle = <&sgmii_phy2>; |
| 108 |
phy-mode = "sgmii"; |
| 109 |
status = "okay"; |
| 110 |
}; |
| 111 |
|
| 112 |
&enet1 { |
| 113 |
tbi-handle = <&tbi1>; |
| 114 |
phy-handle = <&sgmii_phy1>; |
| 115 |
phy-mode = "sgmii"; |
| 116 |
status = "okay"; |
| 117 |
}; |
| 118 |
|
| 119 |
/* RGMII delays added via PCB traces */ |
| 120 |
&enet2 { |
| 121 |
phy-mode = "rgmii"; |
| 122 |
status = "okay"; |
| 123 |
|
| 124 |
fixed-link { |
| 125 |
speed = <1000>; |
| 126 |
full-duplex; |
| 127 |
}; |
| 128 |
}; |
| 129 |
|
| 130 |
&esdhc { |
| 131 |
status = "okay"; |
| 132 |
}; |
| 133 |
|
| 134 |
&i2c0 { |
| 135 |
status = "okay"; |
| 136 |
|
| 137 |
/* 3 axis accelerometer */ |
| 138 |
accelerometer@1e { |
| 139 |
compatible = "fsl,fxls8471"; |
| 140 |
reg = <0x1e>; |
| 141 |
}; |
| 142 |
|
| 143 |
/* Audio codec (SAI2) */ |
| 144 |
audio-codec@2a { |
| 145 |
compatible = "fsl,sgtl5000"; |
| 146 |
VDDIO-supply = <®_vddio_codec>; |
| 147 |
VDDA-supply = <®_vdda_codec>; |
| 148 |
#sound-dai-cells = <0>; |
| 149 |
clocks = <&sys_mclk>; |
| 150 |
reg = <0x2a>; |
| 151 |
}; |
| 152 |
|
| 153 |
/* Current sensing circuit for 1V VDDCORE PMIC rail */ |
| 154 |
current-sensor@44 { |
| 155 |
compatible = "ti,ina220"; |
| 156 |
shunt-resistor = <1000>; |
| 157 |
reg = <0x44>; |
| 158 |
}; |
| 159 |
|
| 160 |
/* Current sensing circuit for 12V VCC rail */ |
| 161 |
current-sensor@45 { |
| 162 |
compatible = "ti,ina220"; |
| 163 |
shunt-resistor = <1000>; |
| 164 |
reg = <0x45>; |
| 165 |
}; |
| 166 |
|
| 167 |
/* Thermal monitor - case */ |
| 168 |
temperature-sensor@48 { |
| 169 |
compatible = "national,lm75"; |
| 170 |
reg = <0x48>; |
| 171 |
}; |
| 172 |
|
| 173 |
/* Thermal monitor - chip */ |
| 174 |
temperature-sensor@4c { |
| 175 |
compatible = "ti,tmp451"; |
| 176 |
reg = <0x4c>; |
| 177 |
}; |
| 178 |
|
| 179 |
eeprom@51 { |
| 180 |
compatible = "atmel,24c32"; |
| 181 |
reg = <0x51>; |
| 182 |
}; |
| 183 |
|
| 184 |
/* Unsupported devices: |
| 185 |
* - FXAS21002C Gyroscope at 0x20 |
| 186 |
* - TI ADS7924 4-channel ADC at 0x49 |
| 187 |
*/ |
| 188 |
}; |
| 189 |
|
| 190 |
&ifc { |
| 191 |
status = "disabled"; |
| 192 |
}; |
| 193 |
|
| 194 |
&lpuart0 { |
| 195 |
status = "okay"; |
| 196 |
}; |
| 197 |
|
| 198 |
&lpuart3 { |
| 199 |
status = "okay"; |
| 200 |
}; |
| 201 |
|
| 202 |
&mdio0 { |
| 203 |
/* AR8031 */ |
| 204 |
sgmii_phy1: ethernet-phy@1 { |
| 205 |
reg = <0x1>; |
| 206 |
/* SGMII1_PHY_INT_B: connected to IRQ2, active low */ |
| 207 |
interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>; |
| 208 |
}; |
| 209 |
|
| 210 |
/* AR8031 */ |
| 211 |
sgmii_phy2: ethernet-phy@2 { |
| 212 |
reg = <0x2>; |
| 213 |
/* SGMII2_PHY_INT_B: connected to IRQ2, active low */ |
| 214 |
interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>; |
| 215 |
}; |
| 216 |
|
| 217 |
/* BCM5464 quad PHY */ |
| 218 |
rgmii_phy3: ethernet-phy@3 { |
| 219 |
reg = <0x3>; |
| 220 |
}; |
| 221 |
|
| 222 |
rgmii_phy4: ethernet-phy@4 { |
| 223 |
reg = <0x4>; |
| 224 |
}; |
| 225 |
|
| 226 |
rgmii_phy5: ethernet-phy@5 { |
| 227 |
reg = <0x5>; |
| 228 |
}; |
| 229 |
|
| 230 |
rgmii_phy6: ethernet-phy@6 { |
| 231 |
reg = <0x6>; |
| 232 |
}; |
| 233 |
|
| 234 |
/* SGMII PCS for enet0 */ |
| 235 |
tbi0: tbi-phy@1f { |
| 236 |
reg = <0x1f>; |
| 237 |
device_type = "tbi-phy"; |
| 238 |
}; |
| 239 |
}; |
| 240 |
|
| 241 |
&mdio1 { |
| 242 |
/* SGMII PCS for enet1 */ |
| 243 |
tbi1: tbi-phy@1f { |
| 244 |
reg = <0x1f>; |
| 245 |
device_type = "tbi-phy"; |
| 246 |
}; |
| 247 |
}; |
| 248 |
|
| 249 |
&qspi { |
| 250 |
status = "okay"; |
| 251 |
|
| 252 |
flash@0 { |
| 253 |
/* Rev. A uses 64MB flash, Rev. B & C use 32MB flash */ |
| 254 |
compatible = "jedec,spi-nor"; |
| 255 |
spi-max-frequency = <20000000>; |
| 256 |
#address-cells = <1>; |
| 257 |
#size-cells = <1>; |
| 258 |
reg = <0>; |
| 259 |
|
| 260 |
partitions { |
| 261 |
compatible = "fixed-partitions"; |
| 262 |
#address-cells = <1>; |
| 263 |
#size-cells = <1>; |
| 264 |
|
| 265 |
partition@0 { |
| 266 |
label = "RCW"; |
| 267 |
reg = <0x0 0x40000>; |
| 268 |
}; |
| 269 |
|
| 270 |
partition@40000 { |
| 271 |
label = "U-Boot"; |
| 272 |
reg = <0x40000 0x300000>; |
| 273 |
}; |
| 274 |
|
| 275 |
partition@340000 { |
| 276 |
label = "U-Boot Env"; |
| 277 |
reg = <0x340000 0x100000>; |
| 278 |
}; |
| 279 |
}; |
| 280 |
}; |
| 281 |
}; |
| 282 |
|
| 283 |
&sai2 { |
| 284 |
status = "okay"; |
| 285 |
}; |
| 286 |
|
| 287 |
&sata { |
| 288 |
status = "okay"; |
| 289 |
}; |
| 290 |
|
| 291 |
&uart0 { |
| 292 |
status = "okay"; |
| 293 |
}; |