| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (c) 2018 Martin Blumenstingl <[email protected]>. |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
|
| 11 |
#include "meson8b.dtsi" |
| 12 |
|
| 13 |
/ { |
| 14 |
model = "Endless Computers Endless Mini"; |
| 15 |
compatible = "endless,ec100", "amlogic,meson8b"; |
| 16 |
|
| 17 |
aliases { |
| 18 |
serial0 = &uart_AO; |
| 19 |
}; |
| 20 |
|
| 21 |
chosen { |
| 22 |
stdout-path = "serial0:115200n8"; |
| 23 |
}; |
| 24 |
|
| 25 |
memory@40000000 { |
| 26 |
device_type = "memory"; |
| 27 |
reg = <0x40000000 0x40000000>; |
| 28 |
}; |
| 29 |
|
| 30 |
emmc_pwrseq: emmc-pwrseq { |
| 31 |
compatible = "mmc-pwrseq-emmc"; |
| 32 |
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; |
| 33 |
}; |
| 34 |
|
| 35 |
gpio-keys { |
| 36 |
compatible = "gpio-keys-polled"; |
| 37 |
poll-interval = <100>; |
| 38 |
|
| 39 |
pal-switch { |
| 40 |
label = "pal"; |
| 41 |
linux,input-type = <EV_SW>; |
| 42 |
linux,code = <KEY_SWITCHVIDEOMODE>; |
| 43 |
gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>; |
| 44 |
}; |
| 45 |
|
| 46 |
ntsc-switch { |
| 47 |
label = "ntsc"; |
| 48 |
linux,input-type = <EV_SW>; |
| 49 |
linux,code = <KEY_SWITCHVIDEOMODE>; |
| 50 |
gpios = <&gpio GPIOH_8 GPIO_ACTIVE_HIGH>; |
| 51 |
}; |
| 52 |
|
| 53 |
power-button { |
| 54 |
label = "power"; |
| 55 |
linux,code = <KEY_POWER>; |
| 56 |
gpios = <&gpio GPIOH_9 GPIO_ACTIVE_LOW>; |
| 57 |
}; |
| 58 |
}; |
| 59 |
|
| 60 |
gpio-poweroff { |
| 61 |
compatible = "gpio-poweroff"; |
| 62 |
/* |
| 63 |
* shutdown is managed by the EC (embedded micro-controller) |
| 64 |
* which is configured through GPIOAO_2 (poweroff GPIO) and |
| 65 |
* GPIOAO_7 (power LED, which has to go LOW as well). |
| 66 |
*/ |
| 67 |
gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>; |
| 68 |
timeout-ms = <20000>; |
| 69 |
}; |
| 70 |
|
| 71 |
leds { |
| 72 |
compatible = "gpio-leds"; |
| 73 |
|
| 74 |
led-power { |
| 75 |
label = "ec100:red:power"; |
| 76 |
/* |
| 77 |
* Needs to go LOW (together with the poweroff GPIO) |
| 78 |
* during shutdown to allow the EC (embedded |
| 79 |
* micro-controller) to shutdown the system. Setting |
| 80 |
* the output to LOW signals the EC to start a |
| 81 |
* "breathing"/pulsing effect until the power is fully |
| 82 |
* turned off. |
| 83 |
*/ |
| 84 |
gpios = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>; |
| 85 |
default-state = "on"; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
rtc32k_xtal: rtc32k-xtal-clk { |
| 90 |
/* X2 in the schematics */ |
| 91 |
compatible = "fixed-clock"; |
| 92 |
clock-frequency = <32768>; |
| 93 |
clock-output-names = "RTC32K"; |
| 94 |
#clock-cells = <0>; |
| 95 |
}; |
| 96 |
|
| 97 |
sound { |
| 98 |
compatible = "amlogic,gx-sound-card"; |
| 99 |
model = "M8B-EC100"; |
| 100 |
|
| 101 |
clocks = <&clkc CLKID_MPLL0>, |
| 102 |
<&clkc CLKID_MPLL1>, |
| 103 |
<&clkc CLKID_MPLL2>; |
| 104 |
|
| 105 |
assigned-clocks = <&clkc CLKID_MPLL0>, |
| 106 |
<&clkc CLKID_MPLL1>, |
| 107 |
<&clkc CLKID_MPLL2>; |
| 108 |
assigned-clock-rates = <270950400>, |
| 109 |
<294912000>, |
| 110 |
<393216000>; |
| 111 |
|
| 112 |
dai-link-0 { |
| 113 |
sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>; |
| 114 |
}; |
| 115 |
|
| 116 |
dai-link-1 { |
| 117 |
sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>; |
| 118 |
dai-format = "i2s"; |
| 119 |
mclk-fs = <256>; |
| 120 |
|
| 121 |
codec-0 { |
| 122 |
sound-dai = <&rt5640>; |
| 123 |
}; |
| 124 |
}; |
| 125 |
}; |
| 126 |
|
| 127 |
usb_vbus: regulator-usb-vbus { |
| 128 |
/* |
| 129 |
* Silergy SY6288CCAC-GP 2A Power Distribution Switch. |
| 130 |
*/ |
| 131 |
compatible = "regulator-fixed"; |
| 132 |
|
| 133 |
regulator-name = "USB_VBUS"; |
| 134 |
|
| 135 |
regulator-min-microvolt = <5000000>; |
| 136 |
regulator-max-microvolt = <5000000>; |
| 137 |
|
| 138 |
vin-supply = <&vcc_5v>; |
| 139 |
|
| 140 |
/* |
| 141 |
* signal name from the schematics: USB_PWR_EN |
| 142 |
*/ |
| 143 |
gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; |
| 144 |
enable-active-high; |
| 145 |
}; |
| 146 |
|
| 147 |
vcc_5v: regulator-vcc5v { |
| 148 |
/* |
| 149 |
* supplied by the main power input which called PWR_5V_STB |
| 150 |
* in the schematics |
| 151 |
*/ |
| 152 |
compatible = "regulator-fixed"; |
| 153 |
|
| 154 |
regulator-name = "VCC5V"; |
| 155 |
|
| 156 |
regulator-min-microvolt = <5000000>; |
| 157 |
regulator-max-microvolt = <5000000>; |
| 158 |
|
| 159 |
/* |
| 160 |
* signal name from the schematics: 3V3_5V_EN |
| 161 |
*/ |
| 162 |
gpio = <&gpio GPIODV_29 GPIO_ACTIVE_LOW>; |
| 163 |
|
| 164 |
regulator-boot-on; |
| 165 |
regulator-always-on; |
| 166 |
}; |
| 167 |
|
| 168 |
vcck: regulator-vcck { |
| 169 |
/* |
| 170 |
* Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz |
| 171 |
* Synchronous Step Down Regulator. |
| 172 |
*/ |
| 173 |
compatible = "pwm-regulator"; |
| 174 |
|
| 175 |
regulator-name = "VCCK"; |
| 176 |
regulator-min-microvolt = <860000>; |
| 177 |
regulator-max-microvolt = <1140000>; |
| 178 |
|
| 179 |
pwm-supply = <&vcc_5v>; |
| 180 |
|
| 181 |
pwms = <&pwm_cd 0 1148 0>; |
| 182 |
pwm-dutycycle-range = <100 0>; |
| 183 |
|
| 184 |
regulator-boot-on; |
| 185 |
regulator-always-on; |
| 186 |
}; |
| 187 |
|
| 188 |
vcc_1v8: regulator-vcc1v8 { |
| 189 |
/* |
| 190 |
* ABLIC S-1339D18-M5001-GP |
| 191 |
*/ |
| 192 |
compatible = "regulator-fixed"; |
| 193 |
|
| 194 |
regulator-name = "VCC1V8"; |
| 195 |
regulator-min-microvolt = <1800000>; |
| 196 |
regulator-max-microvolt = <1800000>; |
| 197 |
|
| 198 |
vin-supply = <&vcc_3v3>; |
| 199 |
}; |
| 200 |
|
| 201 |
vcc_3v3: regulator-vcc3v3 { |
| 202 |
/* |
| 203 |
* Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz |
| 204 |
* Synchronous Step Down Regulator. Also called |
| 205 |
* VDDIO_AO3.3V in the schematics. |
| 206 |
*/ |
| 207 |
compatible = "regulator-fixed"; |
| 208 |
|
| 209 |
regulator-name = "VCC3V3"; |
| 210 |
regulator-min-microvolt = <3300000>; |
| 211 |
regulator-max-microvolt = <3300000>; |
| 212 |
|
| 213 |
vin-supply = <&vcc_5v>; |
| 214 |
}; |
| 215 |
|
| 216 |
vcc_ddr3: regulator-vcc-ddr3 { |
| 217 |
/* |
| 218 |
* Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz |
| 219 |
* Synchronous Step Down Regulator. Also called |
| 220 |
* DDR3_1.5V in the schematics. |
| 221 |
*/ |
| 222 |
compatible = "regulator-fixed"; |
| 223 |
|
| 224 |
regulator-name = "VCC_DDR3_1V5"; |
| 225 |
regulator-min-microvolt = <1500000>; |
| 226 |
regulator-max-microvolt = <1500000>; |
| 227 |
|
| 228 |
vin-supply = <&vcc_5v>; |
| 229 |
|
| 230 |
regulator-boot-on; |
| 231 |
regulator-always-on; |
| 232 |
}; |
| 233 |
|
| 234 |
vcc_rtc: regulator-vcc-rtc { |
| 235 |
/* |
| 236 |
* Global Mixed-mode Technology Inc. G918T12U-GP |
| 237 |
*/ |
| 238 |
compatible = "regulator-fixed"; |
| 239 |
|
| 240 |
regulator-name = "VCC_RTC"; |
| 241 |
regulator-min-microvolt = <900000>; |
| 242 |
regulator-max-microvolt = <900000>; |
| 243 |
|
| 244 |
/* |
| 245 |
* When the board is powered then the input is VCC3V3, |
| 246 |
* otherwise power is taken from the coin cell battery. |
| 247 |
*/ |
| 248 |
vin-supply = <&vcc_3v3>; |
| 249 |
}; |
| 250 |
|
| 251 |
vddee: regulator-vddee { |
| 252 |
/* |
| 253 |
* Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz |
| 254 |
* Synchronous Step Down Regulator. Also called VDDAO |
| 255 |
* in a part of the schematics. |
| 256 |
*/ |
| 257 |
compatible = "pwm-regulator"; |
| 258 |
|
| 259 |
regulator-name = "VDDEE"; |
| 260 |
regulator-min-microvolt = <860000>; |
| 261 |
regulator-max-microvolt = <1140000>; |
| 262 |
|
| 263 |
pwm-supply = <&vcc_5v>; |
| 264 |
|
| 265 |
pwms = <&pwm_cd 1 1148 0>; |
| 266 |
pwm-dutycycle-range = <100 0>; |
| 267 |
|
| 268 |
regulator-boot-on; |
| 269 |
regulator-always-on; |
| 270 |
}; |
| 271 |
}; |
| 272 |
|
| 273 |
&aiu { |
| 274 |
status = "okay"; |
| 275 |
|
| 276 |
pinctrl-0 = <&i2s_am_clk_pins>, <&i2s_out_ao_clk_pins>, |
| 277 |
<&i2s_out_lr_clk_pins>, <&i2s_out_ch01_ao_pins>; |
| 278 |
pinctrl-names = "default"; |
| 279 |
}; |
| 280 |
|
| 281 |
&cpu0 { |
| 282 |
cpu-supply = <&vcck>; |
| 283 |
}; |
| 284 |
|
| 285 |
ðmac { |
| 286 |
status = "okay"; |
| 287 |
|
| 288 |
pinctrl-0 = <ð_rmii_pins>; |
| 289 |
pinctrl-names = "default"; |
| 290 |
|
| 291 |
phy-handle = <ð_phy0>; |
| 292 |
phy-mode = "rmii"; |
| 293 |
|
| 294 |
mdio { |
| 295 |
compatible = "snps,dwmac-mdio"; |
| 296 |
#address-cells = <1>; |
| 297 |
#size-cells = <0>; |
| 298 |
|
| 299 |
eth_phy0: ethernet-phy@0 { |
| 300 |
/* IC Plus IP101A/G (0x02430c54) */ |
| 301 |
reg = <0>; |
| 302 |
|
| 303 |
reset-assert-us = <10000>; |
| 304 |
reset-deassert-us = <10000>; |
| 305 |
reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; |
| 306 |
|
| 307 |
icplus,select-interrupt; |
| 308 |
interrupt-parent = <&gpio_intc>; |
| 309 |
/* GPIOH_3 */ |
| 310 |
interrupts = <17 IRQ_TYPE_LEVEL_LOW>; |
| 311 |
}; |
| 312 |
}; |
| 313 |
}; |
| 314 |
|
| 315 |
&i2c_A { |
| 316 |
status = "okay"; |
| 317 |
pinctrl-0 = <&i2c_a_pins>; |
| 318 |
pinctrl-names = "default"; |
| 319 |
|
| 320 |
rt5640: codec@1c { |
| 321 |
compatible = "realtek,rt5640"; |
| 322 |
|
| 323 |
reg = <0x1c>; |
| 324 |
|
| 325 |
#sound-dai-cells = <0>; |
| 326 |
|
| 327 |
interrupt-parent = <&gpio_intc>; |
| 328 |
interrupts = <13 IRQ_TYPE_EDGE_BOTH>; /* GPIOAO_13 */ |
| 329 |
|
| 330 |
/* |
| 331 |
* TODO: realtek,ldo1-en-gpios is connected to GPIO_BSD_EN. |
| 332 |
* We currently cannot configure this pin correctly. |
| 333 |
* Luckily for us it's in the "right" state by default. |
| 334 |
*/ |
| 335 |
realtek,in1-differential; |
| 336 |
}; |
| 337 |
}; |
| 338 |
|
| 339 |
&mali { |
| 340 |
mali-supply = <&vddee>; |
| 341 |
}; |
| 342 |
|
| 343 |
&saradc { |
| 344 |
status = "okay"; |
| 345 |
vref-supply = <&vcc_1v8>; |
| 346 |
}; |
| 347 |
|
| 348 |
&sdhc { |
| 349 |
status = "okay"; |
| 350 |
|
| 351 |
pinctrl-0 = <&sdxc_c_pins>; |
| 352 |
pinctrl-names = "default"; |
| 353 |
|
| 354 |
bus-width = <8>; |
| 355 |
max-frequency = <50000000>; |
| 356 |
|
| 357 |
cap-mmc-highspeed; |
| 358 |
disable-wp; |
| 359 |
non-removable; |
| 360 |
no-sdio; |
| 361 |
|
| 362 |
mmc-pwrseq = <&emmc_pwrseq>; |
| 363 |
|
| 364 |
vmmc-supply = <&vcc_3v3>; |
| 365 |
vqmmc-supply = <&vcc_3v3>; |
| 366 |
}; |
| 367 |
|
| 368 |
&sdio { |
| 369 |
status = "okay"; |
| 370 |
|
| 371 |
pinctrl-0 = <&sd_b_pins>; |
| 372 |
pinctrl-names = "default"; |
| 373 |
|
| 374 |
/* SD card */ |
| 375 |
sd_card_slot: slot@1 { |
| 376 |
compatible = "mmc-slot"; |
| 377 |
reg = <1>; |
| 378 |
status = "okay"; |
| 379 |
|
| 380 |
bus-width = <4>; |
| 381 |
no-sdio; |
| 382 |
cap-mmc-highspeed; |
| 383 |
cap-sd-highspeed; |
| 384 |
disable-wp; |
| 385 |
|
| 386 |
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>; |
| 387 |
|
| 388 |
vmmc-supply = <&vcc_3v3>; |
| 389 |
}; |
| 390 |
}; |
| 391 |
|
| 392 |
&gpio_ao { |
| 393 |
gpio-line-names = "Linux_TX", "Linux_RX", |
| 394 |
"SLP_S5_N", "USB2_OC_FLAG#", |
| 395 |
"HUB_RST", "USB_PWR_EN", |
| 396 |
"I2S_IN", "SLP_S1_N", |
| 397 |
"TCK", "TMS", "TDI", "TDO", |
| 398 |
"HDMI_CEC", "5640_IRQ", |
| 399 |
"MUTE", "S805_TEST#"; |
| 400 |
}; |
| 401 |
|
| 402 |
&gpio { |
| 403 |
gpio-line-names = /* Bank GPIOX */ |
| 404 |
"WIFI_SD_D0", "WIFI_SD_D1", "WIFI_SD_D2", |
| 405 |
"WIFI_SD_D3", "BTPCM_DOUT", "BTPCM_DIN", |
| 406 |
"BTPCM_SYNC", "BTPCM_CLK", "WIFI_SD_CLK", |
| 407 |
"WIFI_SD_CMD", "WIFI_32K", "WIFI_PWREN", |
| 408 |
"UART_B_TX", "UART_B_RX", "UART_B_CTS_N", |
| 409 |
"UART_B_RTS_N", "BT_EN", "WIFI_WAKE_HOST", |
| 410 |
/* Bank GPIOY */ |
| 411 |
"", "", "", "", "", "", "", "", "", "", |
| 412 |
"", "", |
| 413 |
/* Bank GPIODV */ |
| 414 |
"VCCK_PWM_C", "I2C_SDA_A", "I2C_SCL_A", |
| 415 |
"I2C_SDA_B", "I2C_SCL_B", "VDDEE_PWM_D", |
| 416 |
"VDDEE_PWM 3V3_5V_EN", |
| 417 |
/* Bank GPIOH */ |
| 418 |
"HDMI_HPD", "HDMI_I2C_SDA", "HDMI_I2C_SCL", |
| 419 |
"RMII_IRQ", "RMII_RST#", "RMII_TXD1", |
| 420 |
"RMII_TXD0", "AV_select_1", "AV_select_2", |
| 421 |
"MCU_Control_S", |
| 422 |
/* Bank CARD */ |
| 423 |
"SD_D1_B", "SD_D0_B", "SD_CLK_8726MX", |
| 424 |
"SD_CMD_8726MX", "SD_D3_B", "SD_D2_B", |
| 425 |
"CARD_EN_DET (CARD_DET)", |
| 426 |
/* Bank BOOT */ |
| 427 |
"NAND_D0 (EMMC)", "NAND_D1 (EMMC)", |
| 428 |
"NAND_D2 (EMMC)", "NAND_D3 (EMMC)", |
| 429 |
"NAND_D4 (EMMC)", "NAND_D5 (EMMC)", |
| 430 |
"NAND_D6 (EMMC)", "NAND_D7 (EMMC)", |
| 431 |
"NAND_CS1 (EMMC)", "NAND_CS2 iNAND_RS1 (EMMC)", |
| 432 |
"NAND_nR/B iNAND_CMD (EMMC)", "NAND_ALE (EMMC)", |
| 433 |
"NAND_CLE (EMMC)", "nRE_S1 NAND_nRE (EMMC)", |
| 434 |
"nWE_S1 NAND_nWE (EMMC)", "", "", "", "SPI_CS", |
| 435 |
/* Bank DIF */ |
| 436 |
"RMII_RXD1", "RMII_RXD0", "RMII_CRS_DV", |
| 437 |
"RMII_50M_IN", "GPIODIF_4", "GPIODIF_5", |
| 438 |
"RMII_TXEN", "CPUETH_25MOUT", "RMII_MDC", |
| 439 |
"RMII_MDIO"; |
| 440 |
}; |
| 441 |
|
| 442 |
&pwm_cd { |
| 443 |
status = "okay"; |
| 444 |
pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>; |
| 445 |
pinctrl-names = "default"; |
| 446 |
}; |
| 447 |
|
| 448 |
&rtc { |
| 449 |
status = "okay"; |
| 450 |
clocks = <&rtc32k_xtal>; |
| 451 |
vdd-supply = <&vcc_rtc>; |
| 452 |
}; |
| 453 |
|
| 454 |
/* exposed through the pin headers labeled "URDUG1" on the top of the PCB */ |
| 455 |
&uart_AO { |
| 456 |
status = "okay"; |
| 457 |
pinctrl-0 = <&uart_ao_a_pins>; |
| 458 |
pinctrl-names = "default"; |
| 459 |
}; |
| 460 |
|
| 461 |
/* |
| 462 |
* connected to the Bluetooth part of the RTL8723BS SDIO wifi / Bluetooth |
| 463 |
* combo chip. This is only available on the variant with 2GB RAM. |
| 464 |
*/ |
| 465 |
&uart_B { |
| 466 |
status = "okay"; |
| 467 |
pinctrl-0 = <&uart_b0_pins>, <&uart_b0_cts_rts_pins>; |
| 468 |
pinctrl-names = "default"; |
| 469 |
uart-has-rtscts; |
| 470 |
}; |
| 471 |
|
| 472 |
&usb1 { |
| 473 |
status = "okay"; |
| 474 |
vbus-supply = <&usb_vbus>; |
| 475 |
}; |
| 476 |
|
| 477 |
&usb1_phy { |
| 478 |
status = "okay"; |
| 479 |
}; |