| 1 |
/* 3c574.c: A PCMCIA ethernet driver for the 3com 3c574 "RoadRunner". |
| 2 |
|
| 3 |
Written 1993-1998 by |
| 4 |
Donald Becker, [email protected], (driver core) and |
| 5 |
David Hinds, [email protected] (from his PC card code). |
| 6 |
|
| 7 |
This software may be used and distributed according to the terms of |
| 8 |
the GNU General Public License, incorporated herein by reference. |
| 9 |
|
| 10 |
This driver derives from Donald Becker's 3c509 core, which has the |
| 11 |
following copyright: |
| 12 |
Copyright 1993 United States Government as represented by the |
| 13 |
Director, National Security Agency. |
| 14 |
|
| 15 |
*/ |
| 16 |
|
| 17 |
/* |
| 18 |
Theory of Operation |
| 19 |
|
| 20 |
I. Board Compatibility |
| 21 |
|
| 22 |
This device driver is designed for the 3Com 3c574 PC card Fast Ethernet |
| 23 |
Adapter. |
| 24 |
|
| 25 |
II. Board-specific settings |
| 26 |
|
| 27 |
None -- PC cards are autoconfigured. |
| 28 |
|
| 29 |
III. Driver operation |
| 30 |
|
| 31 |
The 3c574 uses a Boomerang-style interface, without the bus-master capability. |
| 32 |
See the Boomerang driver and documentation for most details. |
| 33 |
|
| 34 |
IV. Notes and chip documentation. |
| 35 |
|
| 36 |
Two added registers are used to enhance PIO performance, RunnerRdCtrl and |
| 37 |
RunnerWrCtrl. These are 11 bit down-counters that are preloaded with the |
| 38 |
count of word (16 bits) reads or writes the driver is about to do to the Rx |
| 39 |
or Tx FIFO. The chip is then able to hide the internal-PCI-bus to PC-card |
| 40 |
translation latency by buffering the I/O operations with an 8 word FIFO. |
| 41 |
Note: No other chip accesses are permitted when this buffer is used. |
| 42 |
|
| 43 |
A second enhancement is that both attribute and common memory space |
| 44 |
0x0800-0x0fff can translated to the PIO FIFO. Thus memory operations (faster |
| 45 |
with *some* PCcard bridges) may be used instead of I/O operations. |
| 46 |
This is enabled by setting the 0x10 bit in the PCMCIA LAN COR. |
| 47 |
|
| 48 |
Some slow PC card bridges work better if they never see a WAIT signal. |
| 49 |
This is configured by setting the 0x20 bit in the PCMCIA LAN COR. |
| 50 |
Only do this after testing that it is reliable and improves performance. |
| 51 |
|
| 52 |
The upper five bits of RunnerRdCtrl are used to window into PCcard |
| 53 |
configuration space registers. Window 0 is the regular Boomerang/Odie |
| 54 |
register set, 1-5 are various PC card control registers, and 16-31 are |
| 55 |
the (reversed!) CIS table. |
| 56 |
|
| 57 |
A final note: writing the InternalConfig register in window 3 with an |
| 58 |
invalid ramWidth is Very Bad. |
| 59 |
|
| 60 |
V. References |
| 61 |
|
| 62 |
http://www.scyld.com/expert/NWay.html |
| 63 |
http://www.national.com/pf/DP/DP83840.html |
| 64 |
|
| 65 |
Thanks to Terry Murphy of 3Com for providing development information for |
| 66 |
earlier 3Com products. |
| 67 |
|
| 68 |
*/ |
| 69 |
|
| 70 |
#include <linux/module.h> |
| 71 |
#include <linux/kernel.h> |
| 72 |
#include <linux/init.h> |
| 73 |
#include <linux/sched.h> |
| 74 |
#include <linux/slab.h> |
| 75 |
#include <linux/string.h> |
| 76 |
#include <linux/timer.h> |
| 77 |
#include <linux/interrupt.h> |
| 78 |
#include <linux/in.h> |
| 79 |
#include <linux/delay.h> |
| 80 |
#include <asm/io.h> |
| 81 |
#include <asm/system.h> |
| 82 |
#include <asm/bitops.h> |
| 83 |
|
| 84 |
#include <linux/netdevice.h> |
| 85 |
#include <linux/etherdevice.h> |
| 86 |
#include <linux/skbuff.h> |
| 87 |
#include <linux/if_arp.h> |
| 88 |
#include <linux/ioport.h> |
| 89 |
|
| 90 |
#include <pcmcia/version.h> |
| 91 |
#include <pcmcia/cs_types.h> |
| 92 |
#include <pcmcia/cs.h> |
| 93 |
#include <pcmcia/cistpl.h> |
| 94 |
#include <pcmcia/cisreg.h> |
| 95 |
#include <pcmcia/ciscode.h> |
| 96 |
#include <pcmcia/ds.h> |
| 97 |
#include <pcmcia/mem_op.h> |
| 98 |
|
| 99 |
/*====================================================================*/ |
| 100 |
|
| 101 |
/* Module parameters */ |
| 102 |
|
| 103 |
MODULE_AUTHOR("David Hinds <[email protected]>"); |
| 104 |
MODULE_DESCRIPTION("3Com 3c574 series PCMCIA ethernet driver"); |
| 105 |
MODULE_LICENSE("GPL"); |
| 106 |
|
| 107 |
#define INT_MODULE_PARM(n, v) static int n = v; MODULE_PARM(n, "i") |
| 108 |
|
| 109 |
/* Now-standard PC card module parameters. */ |
| 110 |
INT_MODULE_PARM(irq_mask, 0xdeb8); |
| 111 |
static int irq_list[4] = { -1 }; |
| 112 |
MODULE_PARM(irq_list, "1-4i"); |
| 113 |
|
| 114 |
/* Maximum events (Rx packets, etc.) to handle at each interrupt. */ |
| 115 |
INT_MODULE_PARM(max_interrupt_work, 32); |
| 116 |
|
| 117 |
/* Force full duplex modes? */ |
| 118 |
INT_MODULE_PARM(full_duplex, 0); |
| 119 |
|
| 120 |
/* Autodetect link polarity reversal? */ |
| 121 |
INT_MODULE_PARM(auto_polarity, 1); |
| 122 |
|
| 123 |
#ifdef PCMCIA_DEBUG |
| 124 |
INT_MODULE_PARM(pc_debug, PCMCIA_DEBUG); |
| 125 |
#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args) |
| 126 |
static char *version = |
| 127 |
"3c574_cs.c 1.70 2003/08/25 15:57:40 Donald Becker/David Hinds, [email protected].\n"; |
| 128 |
#else |
| 129 |
#define DEBUG(n, args...) |
| 130 |
#endif |
| 131 |
|
| 132 |
/*====================================================================*/ |
| 133 |
|
| 134 |
/* Time in jiffies before concluding the transmitter is hung. */ |
| 135 |
#define TX_TIMEOUT ((800*HZ)/1000) |
| 136 |
|
| 137 |
/* To minimize the size of the driver source and make the driver more |
| 138 |
readable not all constants are symbolically defined. |
| 139 |
You'll need the manual if you want to understand driver details anyway. */ |
| 140 |
/* Offsets from base I/O address. */ |
| 141 |
#define EL3_DATA 0x00 |
| 142 |
#define EL3_CMD 0x0e |
| 143 |
#define EL3_STATUS 0x0e |
| 144 |
|
| 145 |
#define EL3WINDOW(win_num) outw(SelectWindow + (win_num), ioaddr + EL3_CMD) |
| 146 |
|
| 147 |
/* The top five bits written to EL3_CMD are a command, the lower |
| 148 |
11 bits are the parameter, if applicable. */ |
| 149 |
enum el3_cmds { |
| 150 |
TotalReset = 0<<11, SelectWindow = 1<<11, StartCoax = 2<<11, |
| 151 |
RxDisable = 3<<11, RxEnable = 4<<11, RxReset = 5<<11, RxDiscard = 8<<11, |
| 152 |
TxEnable = 9<<11, TxDisable = 10<<11, TxReset = 11<<11, |
| 153 |
FakeIntr = 12<<11, AckIntr = 13<<11, SetIntrEnb = 14<<11, |
| 154 |
SetStatusEnb = 15<<11, SetRxFilter = 16<<11, SetRxThreshold = 17<<11, |
| 155 |
SetTxThreshold = 18<<11, SetTxStart = 19<<11, StatsEnable = 21<<11, |
| 156 |
StatsDisable = 22<<11, StopCoax = 23<<11, |
| 157 |
}; |
| 158 |
|
| 159 |
enum elxl_status { |
| 160 |
IntLatch = 0x0001, AdapterFailure = 0x0002, TxComplete = 0x0004, |
| 161 |
TxAvailable = 0x0008, RxComplete = 0x0010, RxEarly = 0x0020, |
| 162 |
IntReq = 0x0040, StatsFull = 0x0080, CmdBusy = 0x1000 }; |
| 163 |
|
| 164 |
/* The SetRxFilter command accepts the following classes: */ |
| 165 |
enum RxFilter { |
| 166 |
RxStation = 1, RxMulticast = 2, RxBroadcast = 4, RxProm = 8 |
| 167 |
}; |
| 168 |
|
| 169 |
enum Window0 { |
| 170 |
Wn0EepromCmd = 10, Wn0EepromData = 12, /* EEPROM command/address, data. */ |
| 171 |
IntrStatus=0x0E, /* Valid in all windows. */ |
| 172 |
}; |
| 173 |
/* These assumes the larger EEPROM. */ |
| 174 |
enum Win0_EEPROM_cmds { |
| 175 |
EEPROM_Read = 0x200, EEPROM_WRITE = 0x100, EEPROM_ERASE = 0x300, |
| 176 |
EEPROM_EWENB = 0x30, /* Enable erasing/writing for 10 msec. */ |
| 177 |
EEPROM_EWDIS = 0x00, /* Disable EWENB before 10 msec timeout. */ |
| 178 |
}; |
| 179 |
|
| 180 |
/* Register window 1 offsets, the window used in normal operation. |
| 181 |
On the "Odie" this window is always mapped at offsets 0x10-0x1f. |
| 182 |
Except for TxFree, which is overlapped by RunnerWrCtrl. */ |
| 183 |
enum Window1 { |
| 184 |
TX_FIFO = 0x10, RX_FIFO = 0x10, RxErrors = 0x14, |
| 185 |
RxStatus = 0x18, Timer=0x1A, TxStatus = 0x1B, |
| 186 |
TxFree = 0x0C, /* Remaining free bytes in Tx buffer. */ |
| 187 |
RunnerRdCtrl = 0x16, RunnerWrCtrl = 0x1c, |
| 188 |
}; |
| 189 |
|
| 190 |
enum Window3 { /* Window 3: MAC/config bits. */ |
| 191 |
Wn3_Config=0, Wn3_MAC_Ctrl=6, Wn3_Options=8, |
| 192 |
}; |
| 193 |
union wn3_config { |
| 194 |
int i; |
| 195 |
struct w3_config_fields { |
| 196 |
unsigned int ram_size:3, ram_width:1, ram_speed:2, rom_size:2; |
| 197 |
int pad8:8; |
| 198 |
unsigned int ram_split:2, pad18:2, xcvr:3, pad21:1, autoselect:1; |
| 199 |
int pad24:7; |
| 200 |
} u; |
| 201 |
}; |
| 202 |
|
| 203 |
enum Window4 { /* Window 4: Xcvr/media bits. */ |
| 204 |
Wn4_FIFODiag = 4, Wn4_NetDiag = 6, Wn4_PhysicalMgmt=8, Wn4_Media = 10, |
| 205 |
}; |
| 206 |
|
| 207 |
|
| 208 |
#define MEDIA_TP 0x00C0 /* Enable link beat and jabber for 10baseT. */ |
| 209 |
|
| 210 |
struct el3_private { |
| 211 |
dev_link_t link; |
| 212 |
struct net_device dev; |
| 213 |
dev_node_t node; |
| 214 |
struct net_device_stats stats; |
| 215 |
u16 advertising, partner; /* NWay media advertisement */ |
| 216 |
unsigned char phys; /* MII device address */ |
| 217 |
unsigned int |
| 218 |
autoselect:1, default_media:3; /* Read from the EEPROM/Wn3_Config. */ |
| 219 |
/* for transceiver monitoring */ |
| 220 |
struct timer_list media; |
| 221 |
u_short media_status; |
| 222 |
u_short fast_poll; |
| 223 |
u_long last_irq; |
| 224 |
}; |
| 225 |
|
| 226 |
/* Set iff a MII transceiver on any interface requires mdio preamble. |
| 227 |
This only set with the original DP83840 on older 3c905 boards, so the extra |
| 228 |
code size of a per-interface flag is not worthwhile. */ |
| 229 |
static char mii_preamble_required = 0; |
| 230 |
|
| 231 |
/* Index of functions. */ |
| 232 |
|
| 233 |
static void tc574_config(dev_link_t *link); |
| 234 |
static void tc574_release(u_long arg); |
| 235 |
static int tc574_event(event_t event, int priority, |
| 236 |
event_callback_args_t *args); |
| 237 |
|
| 238 |
static void mdio_sync(ioaddr_t ioaddr, int bits); |
| 239 |
static int mdio_read(ioaddr_t ioaddr, int phy_id, int location); |
| 240 |
static void mdio_write(ioaddr_t ioaddr, int phy_id, int location, int value); |
| 241 |
static u_short read_eeprom(ioaddr_t ioaddr, int index); |
| 242 |
static void tc574_wait_for_completion(struct net_device *dev, int cmd); |
| 243 |
|
| 244 |
static void tc574_reset(struct net_device *dev); |
| 245 |
static void media_check(u_long arg); |
| 246 |
static int el3_open(struct net_device *dev); |
| 247 |
static int el3_start_xmit(struct sk_buff *skb, struct net_device *dev); |
| 248 |
static void el3_interrupt(int irq, void *dev_id, struct pt_regs *regs); |
| 249 |
static void update_stats(struct net_device *dev); |
| 250 |
static struct net_device_stats *el3_get_stats(struct net_device *dev); |
| 251 |
static int el3_rx(struct net_device *dev, int worklimit); |
| 252 |
static int el3_close(struct net_device *dev); |
| 253 |
static void el3_tx_timeout(struct net_device *dev); |
| 254 |
static int el3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); |
| 255 |
static void set_rx_mode(struct net_device *dev); |
| 256 |
|
| 257 |
static dev_info_t dev_info = "3c574_cs"; |
| 258 |
|
| 259 |
static dev_link_t *tc574_attach(void); |
| 260 |
static void tc574_detach(dev_link_t *); |
| 261 |
|
| 262 |
static dev_link_t *dev_list = NULL; |
| 263 |
|
| 264 |
static void flush_stale_links(void) |
| 265 |
{ |
| 266 |
dev_link_t *link, *next; |
| 267 |
for (link = dev_list; link; link = next) { |
| 268 |
next = link->next; |
| 269 |
if (link->state & DEV_STALE_LINK) |
| 270 |
tc574_detach(link); |
| 271 |
} |
| 272 |
} |
| 273 |
|
| 274 |
static void cs_error(client_handle_t handle, int func, int ret) |
| 275 |
{ |
| 276 |
#if CS_RELEASE_CODE < 0x2911 |
| 277 |
CardServices(ReportError, dev_info, (void *)func, (void *)ret); |
| 278 |
#else |
| 279 |
error_info_t err = { func, ret }; |
| 280 |
CardServices(ReportError, handle, &err); |
| 281 |
#endif |
| 282 |
} |
| 283 |
|
| 284 |
/* |
| 285 |
tc574_attach() creates an "instance" of the driver, allocating |
| 286 |
local data structures for one device. The device is registered |
| 287 |
with Card Services. |
| 288 |
*/ |
| 289 |
|
| 290 |
static dev_link_t *tc574_attach(void) |
| 291 |
{ |
| 292 |
struct el3_private *lp; |
| 293 |
client_reg_t client_reg; |
| 294 |
dev_link_t *link; |
| 295 |
struct net_device *dev; |
| 296 |
int i, ret; |
| 297 |
|
| 298 |
DEBUG(0, "3c574_attach()\n"); |
| 299 |
flush_stale_links(); |
| 300 |
|
| 301 |
/* Create the PC card device object. */ |
| 302 |
lp = kmalloc(sizeof(*lp), GFP_KERNEL); |
| 303 |
if (!lp) return NULL; |
| 304 |
memset(lp, 0, sizeof(*lp)); |
| 305 |
link = &lp->link; dev = &lp->dev; |
| 306 |
link->priv = dev->priv = link->irq.Instance = lp; |
| 307 |
|
| 308 |
init_timer(&link->release); |
| 309 |
link->release.function = &tc574_release; |
| 310 |
link->release.data = (u_long)link; |
| 311 |
link->io.NumPorts1 = 32; |
| 312 |
link->io.Attributes1 = IO_DATA_PATH_WIDTH_16; |
| 313 |
link->irq.Attributes = IRQ_TYPE_EXCLUSIVE | IRQ_HANDLE_PRESENT; |
| 314 |
link->irq.IRQInfo1 = IRQ_INFO2_VALID|IRQ_LEVEL_ID; |
| 315 |
if (irq_list[0] == -1) |
| 316 |
link->irq.IRQInfo2 = irq_mask; |
| 317 |
else |
| 318 |
for (i = 0; i < 4; i++) |
| 319 |
link->irq.IRQInfo2 |= 1 << irq_list[i]; |
| 320 |
link->irq.Handler = &el3_interrupt; |
| 321 |
link->conf.Attributes = CONF_ENABLE_IRQ; |
| 322 |
link->conf.Vcc = 50; |
| 323 |
link->conf.IntType = INT_MEMORY_AND_IO; |
| 324 |
link->conf.ConfigIndex = 1; |
| 325 |
link->conf.Present = PRESENT_OPTION; |
| 326 |
|
| 327 |
/* The EL3-specific entries in the device structure. */ |
| 328 |
dev->hard_start_xmit = &el3_start_xmit; |
| 329 |
dev->get_stats = &el3_get_stats; |
| 330 |
dev->do_ioctl = &el3_ioctl; |
| 331 |
dev->set_multicast_list = &set_rx_mode; |
| 332 |
ether_setup(dev); |
| 333 |
init_dev_name(dev, lp->node); |
| 334 |
dev->open = &el3_open; |
| 335 |
dev->stop = &el3_close; |
| 336 |
#ifdef HAVE_TX_TIMEOUT |
| 337 |
dev->tx_timeout = el3_tx_timeout; |
| 338 |
dev->watchdog_timeo = TX_TIMEOUT; |
| 339 |
#endif |
| 340 |
|
| 341 |
/* Register with Card Services */ |
| 342 |
link->next = dev_list; |
| 343 |
dev_list = link; |
| 344 |
client_reg.dev_info = &dev_info; |
| 345 |
client_reg.Attributes = INFO_IO_CLIENT | INFO_CARD_SHARE; |
| 346 |
client_reg.EventMask = |
| 347 |
CS_EVENT_CARD_INSERTION | CS_EVENT_CARD_REMOVAL | |
| 348 |
CS_EVENT_RESET_PHYSICAL | CS_EVENT_CARD_RESET | |
| 349 |
CS_EVENT_PM_SUSPEND | CS_EVENT_PM_RESUME; |
| 350 |
client_reg.event_handler = &tc574_event; |
| 351 |
client_reg.Version = 0x0210; |
| 352 |
client_reg.event_callback_args.client_data = link; |
| 353 |
ret = CardServices(RegisterClient, &link->handle, &client_reg); |
| 354 |
if (ret != 0) { |
| 355 |
cs_error(link->handle, RegisterClient, ret); |
| 356 |
tc574_detach(link); |
| 357 |
return NULL; |
| 358 |
} |
| 359 |
|
| 360 |
return link; |
| 361 |
} /* tc574_attach */ |
| 362 |
|
| 363 |
/* |
| 364 |
|
| 365 |
This deletes a driver "instance". The device is de-registered |
| 366 |
with Card Services. If it has been released, all local data |
| 367 |
structures are freed. Otherwise, the structures will be freed |
| 368 |
when the device is released. |
| 369 |
|
| 370 |
*/ |
| 371 |
|
| 372 |
static void tc574_detach(dev_link_t *link) |
| 373 |
{ |
| 374 |
struct el3_private *lp = link->priv; |
| 375 |
dev_link_t **linkp; |
| 376 |
|
| 377 |
DEBUG(0, "3c574_detach(0x%p)\n", link); |
| 378 |
|
| 379 |
/* Locate device structure */ |
| 380 |
for (linkp = &dev_list; *linkp; linkp = &(*linkp)->next) |
| 381 |
if (*linkp == link) break; |
| 382 |
if (*linkp == NULL) |
| 383 |
return; |
| 384 |
|
| 385 |
del_timer(&link->release); |
| 386 |
if (link->state & DEV_CONFIG) { |
| 387 |
tc574_release((u_long)link); |
| 388 |
if (link->state & DEV_STALE_CONFIG) { |
| 389 |
link->state |= DEV_STALE_LINK; |
| 390 |
return; |
| 391 |
} |
| 392 |
} |
| 393 |
|
| 394 |
if (link->handle) |
| 395 |
CardServices(DeregisterClient, link->handle); |
| 396 |
|
| 397 |
/* Unlink device structure, free bits */ |
| 398 |
*linkp = link->next; |
| 399 |
if (link->dev) |
| 400 |
unregister_netdev(&lp->dev); |
| 401 |
kfree(lp); |
| 402 |
|
| 403 |
} /* tc574_detach */ |
| 404 |
|
| 405 |
/* |
| 406 |
tc574_config() is scheduled to run after a CARD_INSERTION event |
| 407 |
is received, to configure the PCMCIA socket, and to make the |
| 408 |
ethernet device available to the system. |
| 409 |
*/ |
| 410 |
|
| 411 |
#define CS_CHECK(fn, args...) \ |
| 412 |
while ((last_ret=CardServices(last_fn=(fn), args))!=0) goto cs_failed |
| 413 |
|
| 414 |
static void tc574_config(dev_link_t *link) |
| 415 |
{ |
| 416 |
client_handle_t handle = link->handle; |
| 417 |
struct el3_private *lp = link->priv; |
| 418 |
struct net_device *dev = &lp->dev; |
| 419 |
tuple_t tuple; |
| 420 |
cisparse_t parse; |
| 421 |
u_short buf[32]; |
| 422 |
int last_fn, last_ret, i, j; |
| 423 |
ioaddr_t ioaddr; |
| 424 |
u16 *phys_addr; |
| 425 |
char *cardname; |
| 426 |
|
| 427 |
phys_addr = (u16 *)dev->dev_addr; |
| 428 |
|
| 429 |
DEBUG(0, "3c574_config(0x%p)\n", link); |
| 430 |
|
| 431 |
tuple.Attributes = 0; |
| 432 |
tuple.DesiredTuple = CISTPL_CONFIG; |
| 433 |
CS_CHECK(GetFirstTuple, handle, &tuple); |
| 434 |
tuple.TupleData = (cisdata_t *)buf; |
| 435 |
tuple.TupleDataMax = 64; |
| 436 |
tuple.TupleOffset = 0; |
| 437 |
CS_CHECK(GetTupleData, handle, &tuple); |
| 438 |
CS_CHECK(ParseTuple, handle, &tuple, &parse); |
| 439 |
link->conf.ConfigBase = parse.config.base; |
| 440 |
link->conf.Present = parse.config.rmask[0]; |
| 441 |
|
| 442 |
/* Configure card */ |
| 443 |
link->state |= DEV_CONFIG; |
| 444 |
|
| 445 |
link->io.IOAddrLines = 16; |
| 446 |
for (i = j = 0; j < 0x400; j += 0x20) { |
| 447 |
link->io.BasePort1 = j ^ 0x300; |
| 448 |
i = CardServices(RequestIO, link->handle, &link->io); |
| 449 |
if (i == CS_SUCCESS) break; |
| 450 |
} |
| 451 |
if (i != CS_SUCCESS) { |
| 452 |
cs_error(link->handle, RequestIO, i); |
| 453 |
goto failed; |
| 454 |
} |
| 455 |
CS_CHECK(RequestIRQ, link->handle, &link->irq); |
| 456 |
CS_CHECK(RequestConfiguration, link->handle, &link->conf); |
| 457 |
|
| 458 |
dev->irq = link->irq.AssignedIRQ; |
| 459 |
dev->base_addr = link->io.BasePort1; |
| 460 |
|
| 461 |
if (register_netdev(dev) != 0) { |
| 462 |
printk(KERN_NOTICE "3c574_cs: register_netdev() failed\n"); |
| 463 |
goto failed; |
| 464 |
} |
| 465 |
|
| 466 |
ioaddr = dev->base_addr; |
| 467 |
copy_dev_name(lp->node, dev); |
| 468 |
link->dev = &lp->node; |
| 469 |
|
| 470 |
/* The 3c574 normally uses an EEPROM for configuration info, including |
| 471 |
the hardware address. The future products may include a modem chip |
| 472 |
and put the address in the CIS. */ |
| 473 |
tuple.DesiredTuple = 0x88; |
| 474 |
if (CardServices(GetFirstTuple, handle, &tuple) == CS_SUCCESS) { |
| 475 |
CardServices(GetTupleData, handle, &tuple); |
| 476 |
for (i = 0; i < 3; i++) |
| 477 |
phys_addr[i] = htons(buf[i]); |
| 478 |
} else { |
| 479 |
EL3WINDOW(0); |
| 480 |
for (i = 0; i < 3; i++) |
| 481 |
phys_addr[i] = htons(read_eeprom(ioaddr, i + 10)); |
| 482 |
if (phys_addr[0] == 0x6060) { |
| 483 |
printk(KERN_NOTICE "3c574_cs: IO port conflict at 0x%03lx" |
| 484 |
"-0x%03lx\n", dev->base_addr, dev->base_addr+15); |
| 485 |
goto failed; |
| 486 |
} |
| 487 |
} |
| 488 |
tuple.DesiredTuple = CISTPL_VERS_1; |
| 489 |
if (CardServices(GetFirstTuple, handle, &tuple) == CS_SUCCESS && |
| 490 |
CardServices(GetTupleData, handle, &tuple) == CS_SUCCESS && |
| 491 |
CardServices(ParseTuple, handle, &tuple, &parse) == CS_SUCCESS) { |
| 492 |
cardname = parse.version_1.str + parse.version_1.ofs[1]; |
| 493 |
} else |
| 494 |
cardname = "3Com 3c574"; |
| 495 |
|
| 496 |
printk(KERN_INFO "%s: %s at io %#3lx, irq %d, hw_addr ", |
| 497 |
dev->name, cardname, dev->base_addr, dev->irq); |
| 498 |
|
| 499 |
for (i = 0; i < 6; i++) |
| 500 |
printk("%02X%s", dev->dev_addr[i], ((i<5) ? ":" : ".\n")); |
| 501 |
|
| 502 |
{ |
| 503 |
u_char mcr, *ram_split[] = {"5:3", "3:1", "1:1", "3:5"}; |
| 504 |
union wn3_config config; |
| 505 |
outw(2<<11, ioaddr + RunnerRdCtrl); |
| 506 |
mcr = inb(ioaddr + 2); |
| 507 |
outw(0<<11, ioaddr + RunnerRdCtrl); |
| 508 |
printk(KERN_INFO " ASIC rev %d,", mcr>>3); |
| 509 |
EL3WINDOW(3); |
| 510 |
config.i = inl(ioaddr + Wn3_Config); |
| 511 |
printk(" %dK FIFO split %s Rx:Tx, %sMII interface.\n", |
| 512 |
8 << config.u.ram_size, ram_split[config.u.ram_split], |
| 513 |
config.u.autoselect ? "autoselect " : ""); |
| 514 |
lp->default_media = config.u.xcvr; |
| 515 |
lp->autoselect = config.u.autoselect; |
| 516 |
} |
| 517 |
|
| 518 |
{ |
| 519 |
int phy; |
| 520 |
|
| 521 |
/* Roadrunner only: Turn on the MII transceiver */ |
| 522 |
outw(0x8040, ioaddr + Wn3_Options); |
| 523 |
mdelay(1); |
| 524 |
outw(0xc040, ioaddr + Wn3_Options); |
| 525 |
tc574_wait_for_completion(dev, TxReset); |
| 526 |
tc574_wait_for_completion(dev, RxReset); |
| 527 |
mdelay(1); |
| 528 |
outw(0x8040, ioaddr + Wn3_Options); |
| 529 |
|
| 530 |
EL3WINDOW(4); |
| 531 |
for (phy = 1; phy <= 32; phy++) { |
| 532 |
int mii_status; |
| 533 |
mdio_sync(ioaddr, 32); |
| 534 |
mii_status = mdio_read(ioaddr, phy & 0x1f, 1); |
| 535 |
if (mii_status != 0xffff) { |
| 536 |
lp->phys = phy & 0x1f; |
| 537 |
DEBUG(0, " MII transceiver at index %d, status %x.\n", |
| 538 |
phy, mii_status); |
| 539 |
if ((mii_status & 0x0040) == 0) |
| 540 |
mii_preamble_required = 1; |
| 541 |
break; |
| 542 |
} |
| 543 |
} |
| 544 |
if (phy > 32) { |
| 545 |
printk(KERN_NOTICE " No MII transceivers found!\n"); |
| 546 |
goto failed; |
| 547 |
} |
| 548 |
i = mdio_read(ioaddr, lp->phys, 16) | 0x40; |
| 549 |
mdio_write(ioaddr, lp->phys, 16, i); |
| 550 |
lp->advertising = mdio_read(ioaddr, lp->phys, 4); |
| 551 |
if (full_duplex) { |
| 552 |
/* Only advertise the FD media types. */ |
| 553 |
lp->advertising &= ~0x02a0; |
| 554 |
mdio_write(ioaddr, lp->phys, 4, lp->advertising); |
| 555 |
} |
| 556 |
} |
| 557 |
|
| 558 |
link->state &= ~DEV_CONFIG_PENDING; |
| 559 |
return; |
| 560 |
|
| 561 |
cs_failed: |
| 562 |
cs_error(link->handle, last_fn, last_ret); |
| 563 |
failed: |
| 564 |
tc574_release((u_long)link); |
| 565 |
link->state &= ~DEV_CONFIG_PENDING; |
| 566 |
return; |
| 567 |
|
| 568 |
} /* tc574_config */ |
| 569 |
|
| 570 |
/* |
| 571 |
After a card is removed, tc574_release() will unregister the net |
| 572 |
device, and release the PCMCIA configuration. If the device is |
| 573 |
still open, this will be postponed until it is closed. |
| 574 |
*/ |
| 575 |
|
| 576 |
static void tc574_release(u_long arg) |
| 577 |
{ |
| 578 |
dev_link_t *link = (dev_link_t *)arg; |
| 579 |
|
| 580 |
DEBUG(0, "3c574_release(0x%p)\n", link); |
| 581 |
|
| 582 |
if (link->open) { |
| 583 |
DEBUG(1, "3c574_cs: release postponed, '%s' still open\n", |
| 584 |
link->dev->dev_name); |
| 585 |
link->state |= DEV_STALE_CONFIG; |
| 586 |
return; |
| 587 |
} |
| 588 |
|
| 589 |
CardServices(ReleaseConfiguration, link->handle); |
| 590 |
CardServices(ReleaseIO, link->handle, &link->io); |
| 591 |
CardServices(ReleaseIRQ, link->handle, &link->irq); |
| 592 |
|
| 593 |
link->state &= ~DEV_CONFIG; |
| 594 |
|
| 595 |
} /* tc574_release */ |
| 596 |
|
| 597 |
/* |
| 598 |
The card status event handler. Mostly, this schedules other |
| 599 |
stuff to run after an event is received. A CARD_REMOVAL event |
| 600 |
also sets some flags to discourage the net drivers from trying |
| 601 |
to talk to the card any more. |
| 602 |
*/ |
| 603 |
|
| 604 |
static int tc574_event(event_t event, int priority, |
| 605 |
event_callback_args_t *args) |
| 606 |
{ |
| 607 |
dev_link_t *link = args->client_data; |
| 608 |
struct el3_private *lp = link->priv; |
| 609 |
struct net_device *dev = &lp->dev; |
| 610 |
|
| 611 |
DEBUG(1, "3c574_event(0x%06x)\n", event); |
| 612 |
|
| 613 |
switch (event) { |
| 614 |
case CS_EVENT_CARD_REMOVAL: |
| 615 |
link->state &= ~DEV_PRESENT; |
| 616 |
if (link->state & DEV_CONFIG) { |
| 617 |
netif_device_detach(dev); |
| 618 |
mod_timer(&link->release, jiffies + HZ/20); |
| 619 |
} |
| 620 |
break; |
| 621 |
case CS_EVENT_CARD_INSERTION: |
| 622 |
link->state |= DEV_PRESENT | DEV_CONFIG_PENDING; |
| 623 |
tc574_config(link); |
| 624 |
break; |
| 625 |
case CS_EVENT_PM_SUSPEND: |
| 626 |
link->state |= DEV_SUSPEND; |
| 627 |
/* Fall through... */ |
| 628 |
case CS_EVENT_RESET_PHYSICAL: |
| 629 |
if (link->state & DEV_CONFIG) { |
| 630 |
if (link->open) |
| 631 |
netif_device_detach(dev); |
| 632 |
CardServices(ReleaseConfiguration, link->handle); |
| 633 |
} |
| 634 |
break; |
| 635 |
case CS_EVENT_PM_RESUME: |
| 636 |
link->state &= ~DEV_SUSPEND; |
| 637 |
/* Fall through... */ |
| 638 |
case CS_EVENT_CARD_RESET: |
| 639 |
if (link->state & DEV_CONFIG) { |
| 640 |
CardServices(RequestConfiguration, link->handle, &link->conf); |
| 641 |
if (link->open) { |
| 642 |
tc574_reset(dev); |
| 643 |
netif_device_attach(dev); |
| 644 |
} |
| 645 |
} |
| 646 |
break; |
| 647 |
} |
| 648 |
return 0; |
| 649 |
} /* tc574_event */ |
| 650 |
|
| 651 |
static void dump_status(struct net_device *dev) |
| 652 |
{ |
| 653 |
ioaddr_t ioaddr = dev->base_addr; |
| 654 |
EL3WINDOW(1); |
| 655 |
printk(KERN_INFO " irq status %04x, rx status %04x, tx status " |
| 656 |
"%02x, tx free %04x\n", inw(ioaddr+EL3_STATUS), |
| 657 |
inw(ioaddr+RxStatus), inb(ioaddr+TxStatus), |
| 658 |
inw(ioaddr+TxFree)); |
| 659 |
EL3WINDOW(4); |
| 660 |
printk(KERN_INFO " diagnostics: fifo %04x net %04x ethernet %04x" |
| 661 |
" media %04x\n", inw(ioaddr+0x04), inw(ioaddr+0x06), |
| 662 |
inw(ioaddr+0x08), inw(ioaddr+0x0a)); |
| 663 |
EL3WINDOW(1); |
| 664 |
} |
| 665 |
|
| 666 |
/* |
| 667 |
Use this for commands that may take time to finish |
| 668 |
*/ |
| 669 |
static void tc574_wait_for_completion(struct net_device *dev, int cmd) |
| 670 |
{ |
| 671 |
int i = 1500; |
| 672 |
outw(cmd, dev->base_addr + EL3_CMD); |
| 673 |
while (--i > 0) |
| 674 |
if (!(inw(dev->base_addr + EL3_STATUS) & 0x1000)) break; |
| 675 |
if (i == 0) |
| 676 |
printk(KERN_NOTICE "%s: command 0x%04x did not complete!\n", |
| 677 |
dev->name, cmd); |
| 678 |
} |
| 679 |
|
| 680 |
/* Read a word from the EEPROM using the regular EEPROM access register. |
| 681 |
Assume that we are in register window zero. |
| 682 |
*/ |
| 683 |
static u_short read_eeprom(ioaddr_t ioaddr, int index) |
| 684 |
{ |
| 685 |
int timer; |
| 686 |
outw(EEPROM_Read + index, ioaddr + Wn0EepromCmd); |
| 687 |
/* Pause for at least 162 usec for the read to take place. */ |
| 688 |
for (timer = 1620; timer >= 0; timer--) { |
| 689 |
if ((inw(ioaddr + Wn0EepromCmd) & 0x8000) == 0) |
| 690 |
break; |
| 691 |
} |
| 692 |
return inw(ioaddr + Wn0EepromData); |
| 693 |
} |
| 694 |
|
| 695 |
/* MII transceiver control section. |
| 696 |
Read and write the MII registers using software-generated serial |
| 697 |
MDIO protocol. See the MII specifications or DP83840A data sheet |
| 698 |
for details. |
| 699 |
The maxium data clock rate is 2.5 Mhz. The timing is easily met by the |
| 700 |
slow PC card interface. */ |
| 701 |
|
| 702 |
#define MDIO_SHIFT_CLK 0x01 |
| 703 |
#define MDIO_DIR_WRITE 0x04 |
| 704 |
#define MDIO_DATA_WRITE0 (0x00 | MDIO_DIR_WRITE) |
| 705 |
#define MDIO_DATA_WRITE1 (0x02 | MDIO_DIR_WRITE) |
| 706 |
#define MDIO_DATA_READ 0x02 |
| 707 |
#define MDIO_ENB_IN 0x00 |
| 708 |
|
| 709 |
/* Generate the preamble required for initial synchronization and |
| 710 |
a few older transceivers. */ |
| 711 |
static void mdio_sync(ioaddr_t ioaddr, int bits) |
| 712 |
{ |
| 713 |
int mdio_addr = ioaddr + Wn4_PhysicalMgmt; |
| 714 |
|
| 715 |
/* Establish sync by sending at least 32 logic ones. */ |
| 716 |
while (-- bits >= 0) { |
| 717 |
outw(MDIO_DATA_WRITE1, mdio_addr); |
| 718 |
outw(MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr); |
| 719 |
} |
| 720 |
} |
| 721 |
|
| 722 |
static int mdio_read(ioaddr_t ioaddr, int phy_id, int location) |
| 723 |
{ |
| 724 |
int i; |
| 725 |
int read_cmd = (0xf6 << 10) | (phy_id << 5) | location; |
| 726 |
unsigned int retval = 0; |
| 727 |
int mdio_addr = ioaddr + Wn4_PhysicalMgmt; |
| 728 |
|
| 729 |
if (mii_preamble_required) |
| 730 |
mdio_sync(ioaddr, 32); |
| 731 |
|
| 732 |
/* Shift the read command bits out. */ |
| 733 |
for (i = 14; i >= 0; i--) { |
| 734 |
int dataval = (read_cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0; |
| 735 |
outw(dataval, mdio_addr); |
| 736 |
outw(dataval | MDIO_SHIFT_CLK, mdio_addr); |
| 737 |
} |
| 738 |
/* Read the two transition, 16 data, and wire-idle bits. */ |
| 739 |
for (i = 19; i > 0; i--) { |
| 740 |
outw(MDIO_ENB_IN, mdio_addr); |
| 741 |
retval = (retval << 1) | ((inw(mdio_addr) & MDIO_DATA_READ) ? 1 : 0); |
| 742 |
outw(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr); |
| 743 |
} |
| 744 |
return (retval>>1) & 0xffff; |
| 745 |
} |
| 746 |
|
| 747 |
static void mdio_write(ioaddr_t ioaddr, int phy_id, int location, int value) |
| 748 |
{ |
| 749 |
int write_cmd = 0x50020000 | (phy_id << 23) | (location << 18) | value; |
| 750 |
int mdio_addr = ioaddr + Wn4_PhysicalMgmt; |
| 751 |
int i; |
| 752 |
|
| 753 |
if (mii_preamble_required) |
| 754 |
mdio_sync(ioaddr, 32); |
| 755 |
|
| 756 |
/* Shift the command bits out. */ |
| 757 |
for (i = 31; i >= 0; i--) { |
| 758 |
int dataval = (write_cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0; |
| 759 |
outw(dataval, mdio_addr); |
| 760 |
outw(dataval | MDIO_SHIFT_CLK, mdio_addr); |
| 761 |
} |
| 762 |
/* Leave the interface idle. */ |
| 763 |
for (i = 1; i >= 0; i--) { |
| 764 |
outw(MDIO_ENB_IN, mdio_addr); |
| 765 |
outw(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr); |
| 766 |
} |
| 767 |
|
| 768 |
return; |
| 769 |
} |
| 770 |
|
| 771 |
/* Reset and restore all of the 3c574 registers. */ |
| 772 |
static void tc574_reset(struct net_device *dev) |
| 773 |
{ |
| 774 |
struct el3_private *lp = (struct el3_private *)dev->priv; |
| 775 |
int i, ioaddr = dev->base_addr; |
| 776 |
|
| 777 |
tc574_wait_for_completion(dev, TotalReset|0x10); |
| 778 |
|
| 779 |
/* Clear any transactions in progress. */ |
| 780 |
outw(0, ioaddr + RunnerWrCtrl); |
| 781 |
outw(0, ioaddr + RunnerRdCtrl); |
| 782 |
|
| 783 |
/* Set the station address and mask. */ |
| 784 |
EL3WINDOW(2); |
| 785 |
for (i = 0; i < 6; i++) |
| 786 |
outb(dev->dev_addr[i], ioaddr + i); |
| 787 |
for (; i < 12; i+=2) |
| 788 |
outw(0, ioaddr + i); |
| 789 |
|
| 790 |
/* Reset config options */ |
| 791 |
EL3WINDOW(3); |
| 792 |
outb((dev->mtu > 1500 ? 0x40 : 0), ioaddr + Wn3_MAC_Ctrl); |
| 793 |
outl((lp->autoselect ? 0x01000000 : 0) | 0x0062001b, |
| 794 |
ioaddr + Wn3_Config); |
| 795 |
|
| 796 |
/* Roadrunner only: Turn on the MII transceiver. */ |
| 797 |
outw(0x8040, ioaddr + Wn3_Options); |
| 798 |
mdelay(1); |
| 799 |
outw(0xc040, ioaddr + Wn3_Options); |
| 800 |
tc574_wait_for_completion(dev, TxReset); |
| 801 |
tc574_wait_for_completion(dev, RxReset); |
| 802 |
mdelay(1); |
| 803 |
outw(0x8040, ioaddr + Wn3_Options); |
| 804 |
|
| 805 |
/* Switch to the stats window, and clear all stats by reading. */ |
| 806 |
outw(StatsDisable, ioaddr + EL3_CMD); |
| 807 |
EL3WINDOW(6); |
| 808 |
for (i = 0; i < 10; i++) |
| 809 |
inb(ioaddr + i); |
| 810 |
inw(ioaddr + 10); |
| 811 |
inw(ioaddr + 12); |
| 812 |
EL3WINDOW(4); |
| 813 |
inb(ioaddr + 12); |
| 814 |
inb(ioaddr + 13); |
| 815 |
|
| 816 |
/* .. enable any extra statistics bits.. */ |
| 817 |
outw(0x0040, ioaddr + Wn4_NetDiag); |
| 818 |
/* .. re-sync MII and re-fill what NWay is advertising. */ |
| 819 |
mdio_sync(ioaddr, 32); |
| 820 |
mdio_write(ioaddr, lp->phys, 4, lp->advertising); |
| 821 |
if (!auto_polarity) { |
| 822 |
/* works for TDK 78Q2120 series MII's */ |
| 823 |
int i = mdio_read(ioaddr, lp->phys, 16) | 0x20; |
| 824 |
mdio_write(ioaddr, lp->phys, 16, i); |
| 825 |
} |
| 826 |
|
| 827 |
/* Switch to register set 1 for normal use, just for TxFree. */ |
| 828 |
EL3WINDOW(1); |
| 829 |
|
| 830 |
set_rx_mode(dev); |
| 831 |
outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */ |
| 832 |
outw(RxEnable, ioaddr + EL3_CMD); /* Enable the receiver. */ |
| 833 |
outw(TxEnable, ioaddr + EL3_CMD); /* Enable transmitter. */ |
| 834 |
/* Allow status bits to be seen. */ |
| 835 |
outw(SetStatusEnb | 0xff, ioaddr + EL3_CMD); |
| 836 |
/* Ack all pending events, and set active indicator mask. */ |
| 837 |
outw(AckIntr | IntLatch | TxAvailable | RxEarly | IntReq, |
| 838 |
ioaddr + EL3_CMD); |
| 839 |
outw(SetIntrEnb | IntLatch | TxAvailable | RxComplete | StatsFull |
| 840 |
| AdapterFailure | RxEarly, ioaddr + EL3_CMD); |
| 841 |
} |
| 842 |
|
| 843 |
static int el3_open(struct net_device *dev) |
| 844 |
{ |
| 845 |
struct el3_private *lp = (struct el3_private *)dev->priv; |
| 846 |
dev_link_t *link = &lp->link; |
| 847 |
|
| 848 |
if (!DEV_OK(link)) |
| 849 |
return -ENODEV; |
| 850 |
|
| 851 |
link->open++; |
| 852 |
MOD_INC_USE_COUNT; |
| 853 |
netif_start_queue(dev); |
| 854 |
netif_mark_up(dev); |
| 855 |
|
| 856 |
tc574_reset(dev); |
| 857 |
lp->media.function = &media_check; |
| 858 |
lp->media.data = (u_long)lp; |
| 859 |
lp->media.expires = jiffies + HZ; |
| 860 |
add_timer(&lp->media); |
| 861 |
|
| 862 |
DEBUG(2, "%s: opened, status %4.4x.\n", |
| 863 |
dev->name, inw(dev->base_addr + EL3_STATUS)); |
| 864 |
|
| 865 |
return 0; |
| 866 |
} |
| 867 |
|
| 868 |
static void el3_tx_timeout(struct net_device *dev) |
| 869 |
{ |
| 870 |
struct el3_private *lp = (struct el3_private *)dev->priv; |
| 871 |
ioaddr_t ioaddr = dev->base_addr; |
| 872 |
|
| 873 |
printk(KERN_NOTICE "%s: Transmit timed out!\n", dev->name); |
| 874 |
dump_status(dev); |
| 875 |
lp->stats.tx_errors++; |
| 876 |
dev->trans_start = jiffies; |
| 877 |
/* Issue TX_RESET and TX_START commands. */ |
| 878 |
tc574_wait_for_completion(dev, TxReset); |
| 879 |
outw(TxEnable, ioaddr + EL3_CMD); |
| 880 |
netif_wake_queue(dev); |
| 881 |
} |
| 882 |
|
| 883 |
static void pop_tx_status(struct net_device *dev) |
| 884 |
{ |
| 885 |
struct el3_private *lp = (struct el3_private *)dev->priv; |
| 886 |
ioaddr_t ioaddr = dev->base_addr; |
| 887 |
int i; |
| 888 |
|
| 889 |
/* Clear the Tx status stack. */ |
| 890 |
for (i = 32; i > 0; i--) { |
| 891 |
u_char tx_status = inb(ioaddr + TxStatus); |
| 892 |
if (!(tx_status & 0x84)) break; |
| 893 |
/* reset transmitter on jabber error or underrun */ |
| 894 |
if (tx_status & 0x30) |
| 895 |
tc574_wait_for_completion(dev, TxReset); |
| 896 |
if (tx_status & 0x38) { |
| 897 |
DEBUG(1, "%s: transmit error: status 0x%02x\n", |
| 898 |
dev->name, tx_status); |
| 899 |
outw(TxEnable, ioaddr + EL3_CMD); |
| 900 |
lp->stats.tx_aborted_errors++; |
| 901 |
} |
| 902 |
outb(0x00, ioaddr + TxStatus); /* Pop the status stack. */ |
| 903 |
} |
| 904 |
} |
| 905 |
|
| 906 |
static int el3_start_xmit(struct sk_buff *skb, struct net_device *dev) |
| 907 |
{ |
| 908 |
ioaddr_t ioaddr = dev->base_addr; |
| 909 |
|
| 910 |
tx_timeout_check(dev, el3_tx_timeout); |
| 911 |
skb_tx_check(dev, skb); |
| 912 |
|
| 913 |
DEBUG(3, "%s: el3_start_xmit(length = %ld) called, " |
| 914 |
"status %4.4x.\n", dev->name, (long)skb->len, |
| 915 |
inw(ioaddr + EL3_STATUS)); |
| 916 |
|
| 917 |
outw(skb->len, ioaddr + TX_FIFO); |
| 918 |
outw(0, ioaddr + TX_FIFO); |
| 919 |
outsl(ioaddr + TX_FIFO, skb->data, (skb->len+3)>>2); |
| 920 |
|
| 921 |
dev->trans_start = jiffies; |
| 922 |
|
| 923 |
/* TxFree appears only in Window 1, not offset 0x1c. */ |
| 924 |
if (inw(ioaddr + TxFree) > 1536) { |
| 925 |
netif_start_queue(dev); |
| 926 |
} else |
| 927 |
/* Interrupt us when the FIFO has room for max-sized packet. |
| 928 |
The threshold is in units of dwords. */ |
| 929 |
outw(SetTxThreshold + (1536>>2), ioaddr + EL3_CMD); |
| 930 |
|
| 931 |
DEV_KFREE_SKB (skb); |
| 932 |
pop_tx_status(dev); |
| 933 |
|
| 934 |
return 0; |
| 935 |
} |
| 936 |
|
| 937 |
/* The EL3 interrupt handler. */ |
| 938 |
static void el3_interrupt(int irq, void *dev_id, struct pt_regs *regs) |
| 939 |
{ |
| 940 |
struct el3_private *lp = dev_id; |
| 941 |
struct net_device *dev = &lp->dev; |
| 942 |
ioaddr_t ioaddr, status; |
| 943 |
int work_budget = max_interrupt_work; |
| 944 |
|
| 945 |
if (!netif_device_present(dev)) |
| 946 |
return; |
| 947 |
ioaddr = dev->base_addr; |
| 948 |
|
| 949 |
DEBUG(3, "%s: interrupt, status %4.4x.\n", |
| 950 |
dev->name, inw(ioaddr + EL3_STATUS)); |
| 951 |
|
| 952 |
while ((status = inw(ioaddr + EL3_STATUS)) & |
| 953 |
(IntLatch | RxComplete | RxEarly | StatsFull)) { |
| 954 |
if (!netif_device_present(dev) || |
| 955 |
((status & 0xe000) != 0x2000)) { |
| 956 |
DEBUG(1, "%s: Interrupt from dead card\n", dev->name); |
| 957 |
break; |
| 958 |
} |
| 959 |
|
| 960 |
if (status & RxComplete) |
| 961 |
work_budget = el3_rx(dev, work_budget); |
| 962 |
|
| 963 |
if (status & TxAvailable) { |
| 964 |
DEBUG(3, " TX room bit was handled.\n"); |
| 965 |
/* There's room in the FIFO for a full-sized packet. */ |
| 966 |
outw(AckIntr | TxAvailable, ioaddr + EL3_CMD); |
| 967 |
netif_wake_queue(dev); |
| 968 |
} |
| 969 |
|
| 970 |
if (status & TxComplete) |
| 971 |
pop_tx_status(dev); |
| 972 |
|
| 973 |
if (status & (AdapterFailure | RxEarly | StatsFull)) { |
| 974 |
/* Handle all uncommon interrupts. */ |
| 975 |
if (status & StatsFull) |
| 976 |
update_stats(dev); |
| 977 |
if (status & RxEarly) { |
| 978 |
work_budget = el3_rx(dev, work_budget); |
| 979 |
outw(AckIntr | RxEarly, ioaddr + EL3_CMD); |
| 980 |
} |
| 981 |
if (status & AdapterFailure) { |
| 982 |
u16 fifo_diag; |
| 983 |
EL3WINDOW(4); |
| 984 |
fifo_diag = inw(ioaddr + Wn4_FIFODiag); |
| 985 |
EL3WINDOW(1); |
| 986 |
printk(KERN_NOTICE "%s: adapter failure, FIFO diagnostic" |
| 987 |
" register %04x.\n", dev->name, fifo_diag); |
| 988 |
if (fifo_diag & 0x0400) { |
| 989 |
/* Tx overrun */ |
| 990 |
tc574_wait_for_completion(dev, TxReset); |
| 991 |
outw(TxEnable, ioaddr + EL3_CMD); |
| 992 |
} |
| 993 |
if (fifo_diag & 0x2000) { |
| 994 |
/* Rx underrun */ |
| 995 |
tc574_wait_for_completion(dev, RxReset); |
| 996 |
set_rx_mode(dev); |
| 997 |
outw(RxEnable, ioaddr + EL3_CMD); |
| 998 |
} |
| 999 |
outw(AckIntr | AdapterFailure, ioaddr + EL3_CMD); |
| 1000 |
} |
| 1001 |
} |
| 1002 |
|
| 1003 |
if (--work_budget < 0) { |
| 1004 |
DEBUG(0, "%s: Too much work in interrupt, " |
| 1005 |
"status %4.4x.\n", dev->name, status); |
| 1006 |
/* Clear all interrupts */ |
| 1007 |
outw(AckIntr | 0xFF, ioaddr + EL3_CMD); |
| 1008 |
break; |
| 1009 |
} |
| 1010 |
/* Acknowledge the IRQ. */ |
| 1011 |
outw(AckIntr | IntReq | IntLatch, ioaddr + EL3_CMD); |
| 1012 |
} |
| 1013 |
|
| 1014 |
DEBUG(3, "%s: exiting interrupt, status %4.4x.\n", |
| 1015 |
dev->name, inw(ioaddr + EL3_STATUS)); |
| 1016 |
return; |
| 1017 |
} |
| 1018 |
|
| 1019 |
/* |
| 1020 |
This timer serves two purposes: to check for missed interrupts |
| 1021 |
(and as a last resort, poll the NIC for events), and to monitor |
| 1022 |
the MII, reporting changes in cable status. |
| 1023 |
*/ |
| 1024 |
static void media_check(u_long arg) |
| 1025 |
{ |
| 1026 |
struct el3_private *lp = (struct el3_private *)arg; |
| 1027 |
struct net_device *dev = &lp->dev; |
| 1028 |
ioaddr_t ioaddr = dev->base_addr; |
| 1029 |
u_long flags; |
| 1030 |
u_short /* cable, */ media, partner; |
| 1031 |
|
| 1032 |
if (!netif_device_present(dev)) |
| 1033 |
goto reschedule; |
| 1034 |
|
| 1035 |
/* Check for pending interrupt with expired latency timer: with |
| 1036 |
this, we can limp along even if the interrupt is blocked */ |
| 1037 |
if ((inw(ioaddr + EL3_STATUS) & IntLatch) && |
| 1038 |
(inb(ioaddr + Timer) == 0xff)) { |
| 1039 |
if (!lp->fast_poll) |
| 1040 |
printk(KERN_INFO "%s: interrupt(s) dropped!\n", dev->name); |
| 1041 |
el3_interrupt(dev->irq, lp, NULL); |
| 1042 |
lp->fast_poll = HZ; |
| 1043 |
} |
| 1044 |
if (lp->fast_poll) { |
| 1045 |
lp->fast_poll--; |
| 1046 |
lp->media.expires = jiffies + 2; |
| 1047 |
add_timer(&lp->media); |
| 1048 |
return; |
| 1049 |
} |
| 1050 |
|
| 1051 |
save_flags(flags); |
| 1052 |
cli(); |
| 1053 |
#if 0 |
| 1054 |
outw(2<<11, ioaddr + RunnerRdCtrl); |
| 1055 |
cable = inb(ioaddr); |
| 1056 |
outb(0x20, ioaddr); |
| 1057 |
outw(0, ioaddr + RunnerRdCtrl); |
| 1058 |
#endif |
| 1059 |
EL3WINDOW(4); |
| 1060 |
media = mdio_read(ioaddr, lp->phys, 1); |
| 1061 |
partner = mdio_read(ioaddr, lp->phys, 5); |
| 1062 |
EL3WINDOW(1); |
| 1063 |
restore_flags(flags); |
| 1064 |
|
| 1065 |
#if 0 |
| 1066 |
if (cable & 0x20) |
| 1067 |
printk(KERN_INFO "%s: cable %s\n", dev->name, |
| 1068 |
((cable & 0x08) ? "fixed" : "problem")); |
| 1069 |
#endif |
| 1070 |
if (media != lp->media_status) { |
| 1071 |
if ((media ^ lp->media_status) & 0x0004) |
| 1072 |
printk(KERN_INFO "%s: %s link beat\n", dev->name, |
| 1073 |
(lp->media_status & 0x0004) ? "lost" : "found"); |
| 1074 |
if ((media ^ lp->media_status) & 0x0020) { |
| 1075 |
lp->partner = 0; |
| 1076 |
if (lp->media_status & 0x0020) { |
| 1077 |
printk(KERN_INFO "%s: autonegotiation restarted\n", |
| 1078 |
dev->name); |
| 1079 |
} else if (partner) { |
| 1080 |
partner &= lp->advertising; |
| 1081 |
lp->partner = partner; |
| 1082 |
printk(KERN_INFO "%s: autonegotiation complete: " |
| 1083 |
"%sbaseT-%cD selected\n", dev->name, |
| 1084 |
((partner & 0x0180) ? "100" : "10"), |
| 1085 |
((partner & 0x0140) ? 'F' : 'H')); |
| 1086 |
} else { |
| 1087 |
printk(KERN_INFO "%s: link partner did not autonegotiate\n", |
| 1088 |
dev->name); |
| 1089 |
} |
| 1090 |
|
| 1091 |
EL3WINDOW(3); |
| 1092 |
outb((partner & 0x0140 ? 0x20 : 0) | |
| 1093 |
(dev->mtu > 1500 ? 0x40 : 0), ioaddr + Wn3_MAC_Ctrl); |
| 1094 |
EL3WINDOW(1); |
| 1095 |
|
| 1096 |
} |
| 1097 |
if (media & 0x0010) |
| 1098 |
printk(KERN_INFO "%s: remote fault detected\n", |
| 1099 |
dev->name); |
| 1100 |
if (media & 0x0002) |
| 1101 |
printk(KERN_INFO "%s: jabber detected\n", dev->name); |
| 1102 |
lp->media_status = media; |
| 1103 |
} |
| 1104 |
|
| 1105 |
reschedule: |
| 1106 |
lp->media.expires = jiffies + HZ; |
| 1107 |
add_timer(&lp->media); |
| 1108 |
} |
| 1109 |
|
| 1110 |
static struct net_device_stats *el3_get_stats(struct net_device *dev) |
| 1111 |
{ |
| 1112 |
struct el3_private *lp = (struct el3_private *)dev->priv; |
| 1113 |
|
| 1114 |
if (netif_device_present(dev)) |
| 1115 |
update_stats(dev); |
| 1116 |
return &lp->stats; |
| 1117 |
} |
| 1118 |
|
| 1119 |
/* Update statistics. |
| 1120 |
Suprisingly this need not be run single-threaded, but it effectively is. |
| 1121 |
The counters clear when read, so the adds must merely be atomic. |
| 1122 |
*/ |
| 1123 |
static void update_stats(struct net_device *dev) |
| 1124 |
{ |
| 1125 |
struct el3_private *lp = (struct el3_private *)dev->priv; |
| 1126 |
ioaddr_t ioaddr = dev->base_addr; |
| 1127 |
u8 rx, tx, up; |
| 1128 |
|
| 1129 |
DEBUG(2, "%s: updating the statistics.\n", dev->name); |
| 1130 |
|
| 1131 |
if (inw(ioaddr+EL3_STATUS) == 0xffff) /* No card. */ |
| 1132 |
return; |
| 1133 |
|
| 1134 |
/* Unlike the 3c509 we need not turn off stats updates while reading. */ |
| 1135 |
/* Switch to the stats window, and read everything. */ |
| 1136 |
EL3WINDOW(6); |
| 1137 |
lp->stats.tx_carrier_errors += inb(ioaddr + 0); |
| 1138 |
lp->stats.tx_heartbeat_errors += inb(ioaddr + 1); |
| 1139 |
/* Multiple collisions. */ inb(ioaddr + 2); |
| 1140 |
lp->stats.collisions += inb(ioaddr + 3); |
| 1141 |
lp->stats.tx_window_errors += inb(ioaddr + 4); |
| 1142 |
lp->stats.rx_fifo_errors += inb(ioaddr + 5); |
| 1143 |
lp->stats.tx_packets += inb(ioaddr + 6); |
| 1144 |
up = inb(ioaddr + 9); |
| 1145 |
lp->stats.tx_packets += (up&0x30) << 4; |
| 1146 |
/* Rx packets */ inb(ioaddr + 7); |
| 1147 |
/* Tx deferrals */ inb(ioaddr + 8); |
| 1148 |
rx = inw(ioaddr + 10); |
| 1149 |
tx = inw(ioaddr + 12); |
| 1150 |
|
| 1151 |
EL3WINDOW(4); |
| 1152 |
/* BadSSD */ inb(ioaddr + 12); |
| 1153 |
up = inb(ioaddr + 13); |
| 1154 |
|
| 1155 |
add_tx_bytes(&lp->stats, tx + ((up & 0xf0) << 12)); |
| 1156 |
|
| 1157 |
EL3WINDOW(1); |
| 1158 |
} |
| 1159 |
|
| 1160 |
static int el3_rx(struct net_device *dev, int worklimit) |
| 1161 |
{ |
| 1162 |
struct el3_private *lp = (struct el3_private *)dev->priv; |
| 1163 |
ioaddr_t ioaddr = dev->base_addr; |
| 1164 |
short rx_status; |
| 1165 |
|
| 1166 |
DEBUG(3, "%s: in rx_packet(), status %4.4x, rx_status %4.4x.\n", |
| 1167 |
dev->name, inw(ioaddr+EL3_STATUS), inw(ioaddr+RxStatus)); |
| 1168 |
while (!((rx_status = inw(ioaddr + RxStatus)) & 0x8000) && |
| 1169 |
(--worklimit >= 0)) { |
| 1170 |
if (rx_status & 0x4000) { /* Error, update stats. */ |
| 1171 |
short error = rx_status & 0x3800; |
| 1172 |
lp->stats.rx_errors++; |
| 1173 |
switch (error) { |
| 1174 |
case 0x0000: lp->stats.rx_over_errors++; break; |
| 1175 |
case 0x0800: lp->stats.rx_length_errors++; break; |
| 1176 |
case 0x1000: lp->stats.rx_frame_errors++; break; |
| 1177 |
case 0x1800: lp->stats.rx_length_errors++; break; |
| 1178 |
case 0x2000: lp->stats.rx_frame_errors++; break; |
| 1179 |
case 0x2800: lp->stats.rx_crc_errors++; break; |
| 1180 |
} |
| 1181 |
} else { |
| 1182 |
short pkt_len = rx_status & 0x7ff; |
| 1183 |
struct sk_buff *skb; |
| 1184 |
|
| 1185 |
skb = dev_alloc_skb(pkt_len+5); |
| 1186 |
|
| 1187 |
DEBUG(3, " Receiving packet size %d status %4.4x.\n", |
| 1188 |
pkt_len, rx_status); |
| 1189 |
if (skb != NULL) { |
| 1190 |
skb->dev = dev; |
| 1191 |
skb_reserve(skb, 2); |
| 1192 |
insl(ioaddr+RX_FIFO, skb_put(skb, pkt_len), |
| 1193 |
((pkt_len+3)>>2)); |
| 1194 |
skb->protocol = eth_type_trans(skb, dev); |
| 1195 |
netif_rx(skb); |
| 1196 |
dev->last_rx = jiffies; |
| 1197 |
lp->stats.rx_packets++; |
| 1198 |
add_rx_bytes(&lp->stats, pkt_len); |
| 1199 |
} else { |
| 1200 |
DEBUG(1, "%s: couldn't allocate a sk_buff of" |
| 1201 |
" size %d.\n", dev->name, pkt_len); |
| 1202 |
lp->stats.rx_dropped++; |
| 1203 |
} |
| 1204 |
} |
| 1205 |
tc574_wait_for_completion(dev, RxDiscard); |
| 1206 |
} |
| 1207 |
|
| 1208 |
return worklimit; |
| 1209 |
} |
| 1210 |
|
| 1211 |
/* Provide ioctl() calls to examine the MII xcvr state. */ |
| 1212 |
static int el3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) |
| 1213 |
{ |
| 1214 |
struct el3_private *lp = (struct el3_private *)dev->priv; |
| 1215 |
ioaddr_t ioaddr = dev->base_addr; |
| 1216 |
u16 *data = (u16 *)&rq->ifr_data; |
| 1217 |
int phy = lp->phys & 0x1f; |
| 1218 |
|
| 1219 |
DEBUG(2, "%s: In ioct(%-.6s, %#4.4x) %4.4x %4.4x %4.4x %4.4x.\n", |
| 1220 |
dev->name, rq->ifr_ifrn.ifrn_name, cmd, |
| 1221 |
data[0], data[1], data[2], data[3]); |
| 1222 |
|
| 1223 |
switch(cmd) { |
| 1224 |
case SIOCDEVPRIVATE: /* Get the address of the PHY in use. */ |
| 1225 |
data[0] = phy; |
| 1226 |
case SIOCDEVPRIVATE+1: /* Read the specified MII register. */ |
| 1227 |
{ |
| 1228 |
int saved_window; |
| 1229 |
long flags; |
| 1230 |
|
| 1231 |
save_flags(flags); |
| 1232 |
cli(); |
| 1233 |
saved_window = inw(ioaddr + EL3_CMD) >> 13; |
| 1234 |
EL3WINDOW(4); |
| 1235 |
data[3] = mdio_read(ioaddr, data[0] & 0x1f, data[1] & 0x1f); |
| 1236 |
EL3WINDOW(saved_window); |
| 1237 |
restore_flags(flags); |
| 1238 |
return 0; |
| 1239 |
} |
| 1240 |
case SIOCDEVPRIVATE+2: /* Write the specified MII register */ |
| 1241 |
{ |
| 1242 |
int saved_window; |
| 1243 |
long flags; |
| 1244 |
|
| 1245 |
if (!capable(CAP_NET_ADMIN)) |
| 1246 |
return -EPERM; |
| 1247 |
save_flags(flags); |
| 1248 |
cli(); |
| 1249 |
saved_window = inw(ioaddr + EL3_CMD) >> 13; |
| 1250 |
EL3WINDOW(4); |
| 1251 |
mdio_write(ioaddr, data[0] & 0x1f, data[1] & 0x1f, data[2]); |
| 1252 |
EL3WINDOW(saved_window); |
| 1253 |
restore_flags(flags); |
| 1254 |
return 0; |
| 1255 |
} |
| 1256 |
default: |
| 1257 |
return -EOPNOTSUPP; |
| 1258 |
} |
| 1259 |
} |
| 1260 |
|
| 1261 |
/* The Odie chip has a 64 bin multicast filter, but the bit layout is not |
| 1262 |
documented. Until it is we revert to receiving all multicast frames when |
| 1263 |
any multicast reception is desired. |
| 1264 |
Note: My other drivers emit a log message whenever promiscuous mode is |
| 1265 |
entered to help detect password sniffers. This is less desirable on |
| 1266 |
typical PC card machines, so we omit the message. |
| 1267 |
*/ |
| 1268 |
|
| 1269 |
static void set_rx_mode(struct net_device *dev) |
| 1270 |
{ |
| 1271 |
ioaddr_t ioaddr = dev->base_addr; |
| 1272 |
|
| 1273 |
if (dev->flags & IFF_PROMISC) |
| 1274 |
outw(SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm, |
| 1275 |
ioaddr + EL3_CMD); |
| 1276 |
else if (dev->mc_count || (dev->flags & IFF_ALLMULTI)) |
| 1277 |
outw(SetRxFilter|RxStation|RxMulticast|RxBroadcast, ioaddr + EL3_CMD); |
| 1278 |
else |
| 1279 |
outw(SetRxFilter | RxStation | RxBroadcast, ioaddr + EL3_CMD); |
| 1280 |
} |
| 1281 |
|
| 1282 |
static int el3_close(struct net_device *dev) |
| 1283 |
{ |
| 1284 |
ioaddr_t ioaddr = dev->base_addr; |
| 1285 |
struct el3_private *lp = dev->priv; |
| 1286 |
dev_link_t *link = &lp->link; |
| 1287 |
|
| 1288 |
DEBUG(2, "%s: shutting down ethercard.\n", dev->name); |
| 1289 |
|
| 1290 |
if (DEV_OK(link)) { |
| 1291 |
/* Turn off statistics ASAP. We update lp->stats below. */ |
| 1292 |
outw(StatsDisable, ioaddr + EL3_CMD); |
| 1293 |
|
| 1294 |
/* Disable the receiver and transmitter. */ |
| 1295 |
outw(RxDisable, ioaddr + EL3_CMD); |
| 1296 |
outw(TxDisable, ioaddr + EL3_CMD); |
| 1297 |
|
| 1298 |
/* Note: Switching to window 0 may disable the IRQ. */ |
| 1299 |
EL3WINDOW(0); |
| 1300 |
|
| 1301 |
update_stats(dev); |
| 1302 |
} |
| 1303 |
|
| 1304 |
link->open--; |
| 1305 |
netif_stop_queue(dev); |
| 1306 |
netif_mark_down(dev); |
| 1307 |
del_timer(&lp->media); |
| 1308 |
if (link->state & DEV_STALE_CONFIG) |
| 1309 |
mod_timer(&link->release, jiffies + HZ/20); |
| 1310 |
|
| 1311 |
MOD_DEC_USE_COUNT; |
| 1312 |
|
| 1313 |
return 0; |
| 1314 |
} |
| 1315 |
|
| 1316 |
static int __init init_3c574_cs(void) |
| 1317 |
{ |
| 1318 |
servinfo_t serv; |
| 1319 |
|
| 1320 |
DEBUG(0, "%s\n", version); |
| 1321 |
CardServices(GetCardServicesInfo, &serv); |
| 1322 |
if (serv.Revision != CS_RELEASE_CODE) { |
| 1323 |
printk(KERN_NOTICE "3c574_cs: Card Services release " |
| 1324 |
"does not match!\n"); |
| 1325 |
return -EINVAL; |
| 1326 |
} |
| 1327 |
register_pccard_driver(&dev_info, &tc574_attach, &tc574_detach); |
| 1328 |
return 0; |
| 1329 |
} |
| 1330 |
|
| 1331 |
static void __exit exit_3c574_cs(void) |
| 1332 |
{ |
| 1333 |
DEBUG(0, "3c574_cs: unloading\n"); |
| 1334 |
unregister_pccard_driver(&dev_info); |
| 1335 |
while (dev_list != NULL) |
| 1336 |
tc574_detach(dev_list); |
| 1337 |
} |
| 1338 |
|
| 1339 |
module_init(init_3c574_cs); |
| 1340 |
module_exit(exit_3c574_cs); |
| 1341 |
|
| 1342 |
/* |
| 1343 |
* Local variables: |
| 1344 |
* compile-command: "make 3c574_cs.o" |
| 1345 |
* c-indent-level: 4 |
| 1346 |
* c-basic-offset: 4 |
| 1347 |
* tab-width: 4 |
| 1348 |
* End: |
| 1349 |
*/ |