| 1 |
Guinier analysis |
| 2 |
------------------ |
| 3 |
.. _saxs_guinier: |
| 4 |
|
| 5 |
This tutorial covers basic principles and best practices for doing a |
| 6 |
Guinier analysis. This is not a tutorial on how to use RAW for this type |
| 7 |
of analysis. For that, please see the :ref:`RAW tutorial <s1p2>`. |
| 8 |
|
| 9 |
|
| 10 |
Overview |
| 11 |
^^^^^^^^^^^^^^^^^ |
| 12 |
|
| 13 |
Guinier’s approximation states that at low-*q* the scattering profile |
| 14 |
can be approximated as follows: |
| 15 |
|
| 16 |
.. math:: |
| 17 |
|
| 18 |
I(q)\approx I(0) e^{-q^2 R_g^2 /3} |
| 19 |
|
| 20 |
where |Rg| is the radius of gyration and I(0) is the intensity at zero scattering |
| 21 |
angle (q=0). Because of the exponential in the Guinier approximation, |Rg| and I(0) can be |
| 22 |
determined by performing a linear fit to a plot of :math:`\ln(I)` |
| 23 |
vs. :math:`q^2`, called the Guinier plot. The region chosen for the linear |
| 24 |
fit is called the "Guinier region." |
| 25 |
|
| 26 |
The Guinier fit provides information on the overall size of the molecule, and |
| 27 |
about the quality of your data. |
| 28 |
|
| 29 |
Why do we do a Guinier fit? |
| 30 |
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| 31 |
|
| 32 |
The Guinier fit is done for two reasons. First, you get the |Rg| and I(0) parameters. |
| 33 |
The |Rg| tells you about the overall size of the molecule, while I(0) depends |
| 34 |
on the molecular weight times the concentration. These parameters are useful |
| 35 |
characterizations of your molecule, and are also needed to calculate |
| 36 |
other information from the SAXS data, including molecular weight and |
| 37 |
volume. |
| 38 |
|
| 39 |
Second, and perhaps most importantly, many of the problems that can affect |
| 40 |
your SAXS data will show up in the low q region, including: |
| 41 |
|
| 42 |
* Aggregation |
| 43 |
* Radiation damage |
| 44 |
* Interparticle interactions |
| 45 |
* Buffer mismatch (in some cases) |
| 46 |
|
| 47 |
These data quality issues cause deviations from linearity in the Guinier region. |
| 48 |
For this reason, having a good Guinier fit is one of the primary ways we assess |
| 49 |
the quality of SAXS data. A good Guinier is a strong indicator that your data |
| 50 |
is from a monodisperse sample and is otherwise free of artifacts. If you cannot |
| 51 |
obtain a good Guinier fit, or you can only obtain a good Guinier fit by |
| 52 |
excluding a significant amount of data at the lowest *q* values, then your |
| 53 |
data probably has one or more of the problems listed above and usually should |
| 54 |
not be used for further analysis. |
| 55 |
|
| 56 |
|
| 57 |
How do we do a Guinier fit? |
| 58 |
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| 59 |
|
| 60 |
The Guinier approximation only holds when the exponential :math:`\exp(-q^2 R_g^2 /3)` |
| 61 |
is small. This means that in order to do a good Guinier fit, we need |
| 62 |
|qRg| to be sufficiently small. The |qRg| value at which the Guinier approximation |
| 63 |
starts to fail for a given scattering profile depends on the overall shape |
| 64 |
of the scatterer. Below is a figure showing the Guinier approximation (black), |
| 65 |
and the scattering intensity for a sphere, thin rod, and thin disc (all with |
| 66 |
the same |Rg|). |
| 67 |
|
| 68 |
.. figure:: images/guinier_shapes.png |
| 69 |
:target: ../_images/guinier_shapes.png |
| 70 |
|
| 71 |
Plot based on Figure 3.3 in [1]. Intensity for the geometric shapes |
| 72 |
from Table 3.4 in [1]. Dashed lines are at |qRg| of 1.0 and 1.3 |
| 73 |
((qR\ :sub:`g`) :sup:`2` of 1.0 and 1.69). |
| 74 |
|
| 75 |
As you can see, the scattering intensity for the rod only agrees with the |
| 76 |
Guinier approximation until :math:`qR_g\sim 1.0`, the sphere until :math:`qR_g\sim 1.3`, |
| 77 |
and the disc until :math:`qR_g\sim 1.7`. Thus, depending on the overall particle shape, you |
| 78 |
should fit different amounts of the low q data to have a good Guinier fit. (Note: |
| 79 |
the plot's x axis is (qR\ :sub:`g`) :sup:`2`, so :math:`qR_g\sim 1.3` appears |
| 80 |
as the dashed line at 1.69) |
| 81 |
|
| 82 |
In practice, we fit both globular (sphere-like and disc-like) objects until :math:`qR_g\sim 1.3`. |
| 83 |
while we fit highly extended (rod-like) objects until :math:`qR_g\sim 1.0`. These values were chosen to |
| 84 |
have <10% error resulting from the deviation of actual shape from the Guinier approximation. |
| 85 |
The reason we accept that much deviation is that you also get uncertainty from |
| 86 |
fitting fewer points in your data, so there is a trade-off between how well |
| 87 |
the approximation works (fitting to smaller maximum |qRg|) and how well you can |
| 88 |
fit your data (fitting to larger maximum |qRg|). |
| 89 |
|
| 90 |
The range of the Guinier fit is thus ideally from the earliest available *q* |
| 91 |
value until a maximum |qRg| of 1.0 or 1.3. However, given that |Rg| is derived |
| 92 |
from the Guinier fit, how do you determine the correct maximum q value for the |
| 93 |
end of the fit? The answer is that the Guinier fit is done iteratively: |
| 94 |
|
| 95 |
#. Guess a starting maximum q value for the fit. |
| 96 |
#. Calculate the Guinier fit and get |Rg|. |
| 97 |
#. If q\ :sub:`max`\ R\ :sub:`g` > 1.3 (or 1.0), reduce the maximum q. If |
| 98 |
q\ :sub:`max`\ R\ :sub:`g` < 1.3 (or 1.0), increase the maximum q. |
| 99 |
#. Repeat steps 2 and 3 until you converge on a final maximum q. |
| 100 |
|
| 101 |
Most software these days will do this iterative search for you, and for good |
| 102 |
quality data will provide you with a reasonable maximum q value that may |
| 103 |
need just a bit of manual refinement. |
| 104 |
|
| 105 |
The minimum q value of a Guinier fit is usually determined by the minimum available |
| 106 |
q value in your data, which is set by the instrument on which you make the measurement. |
| 107 |
However, it is important to have a small enough minimum q to have a reasonable |
| 108 |
range for the Guinier fit. Typically, the minimum |qRg| value should be |
| 109 |
:math:`qR_g\leq 0.65`, though for globular systems it can be okay to have |
| 110 |
:math:`qR_g\leq 1.0`. This means that the minimum q value required depends on the size |
| 111 |
of the system measured. In some cases, with particularly large systems, you may |
| 112 |
have to deliberately seek out an instrument that can measure to sufficiently low q. |
| 113 |
|
| 114 |
If your data has quality issues at low q, which can be caused by the problems |
| 115 |
listed above, you may find that excluding those data from the fit can improve |
| 116 |
the quality of the fit. While this can be acceptable, you should proceed |
| 117 |
with caution when doing that, and always show the full data range on plots. |
| 118 |
The most acceptable case for this to happen is when the first few points |
| 119 |
are either too high or too low, but the rest of the range fits perfectly |
| 120 |
(see below for criteria for a good fit). In that case, those couple of points |
| 121 |
closest to the beamstop may have poor statistics or higher instrumental |
| 122 |
background scattering, and can usually be safely ignored. |
| 123 |
|
| 124 |
|
| 125 |
Criteria for a good Guinier fit |
| 126 |
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| 127 |
|
| 128 |
You are looking for four essential components in your Guinier fit: |
| 129 |
|
| 130 |
#. :math:`\mathbf{q_{min}R_g<0.65}` **.** |
| 131 |
|
| 132 |
* The minimum q of your fit, q\ :sub:`min`, times the |Rg| of your fit |
| 133 |
should be less than 0.65. This criteria ensures you have enough q range to |
| 134 |
properly calculate the |Rg| and I(0) values. For globular particles |
| 135 |
(sphere- or disk-like), you can get away with :math:`q_{min}R_g<1.0`. |
| 136 |
|
| 137 |
#. :math:`\mathbf{q_{max}R_g \sim 1.3}` **(globular) or** |
| 138 |
:math:`\mathbf{q_{max}R_g \sim 1.0}` **(extended).** |
| 139 |
|
| 140 |
* The maximum *q* of your fit, q\ :sub:`max`, times the |Rg| of your fit |
| 141 |
should be less than 1.3 for globular (sphere- and disc-like) particles |
| 142 |
and less than 1.0 for extended (rod-like) particles. This ensures you |
| 143 |
remain in the linear range of the Guinier approximation for the fit. |
| 144 |
|
| 145 |
#. **The Guinier fit residuals should be flat and randomly distributed about zero.** |
| 146 |
|
| 147 |
* If your residuals have a ‘smile’ (above zero near start and end of fit, |
| 148 |
below in the middle), or a ‘frown’ (below zero near start and end |
| 149 |
of fit, above in the middle), it indicates you have non-ideal data. |
| 150 |
The ‘smile’ is characteristic of aggregation, the ‘frown’ characteristic |
| 151 |
of interparticle repulsion. |
| 152 |
|
| 153 |
#. **The fit extends to the lowest available q point.** |
| 154 |
|
| 155 |
* You shouldn’t have to excluded very many points at the start of the fit. |
| 156 |
A few is generally fine, as the points nearest the beamstop can be noisy |
| 157 |
(depending on the exact details of the measurement). Having to exclude |
| 158 |
more than 3-5 points at the low *q* may indicate a problem with your data. |
| 159 |
|
| 160 |
.. figure:: images/guinier_good_gi.png |
| 161 |
:target: ../_images/guinier_good_gi.png |
| 162 |
|
| 163 |
A Guinier fit done in RAW for glucose isomerase (available in the RAW |
| 164 |
Tutorial data). This shows what a good Guinier fit looks like. It has |
| 165 |
:math:`q_{min}R_g<0.65`, :math:`q_{max}R_g \sim 1.3`, the normalized fit |
| 166 |
residual (bottom plot) is flat and randomly distributed about zero, |
| 167 |
and the fit extends to the lowest *q* point available. |
| 168 |
|
| 169 |
Having a good Guinier fit is a major quality check, and a good sign that |
| 170 |
your data is from a monodisperse sample with no interparticle interactions. |
| 171 |
|
| 172 |
What is a bad Guinier fit, and what does it mean? |
| 173 |
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ |
| 174 |
|
| 175 |
Non-linearities in your Guinier fit are indicative or problems in your sample. |
| 176 |
The type of non-linearity can indicate what the problem may be. The figure |
| 177 |
below gives a quick summary off the most common pathologies, more detail is |
| 178 |
available in the sections below. |
| 179 |
|
| 180 |
.. figure:: images/guinier_overview_jacques.png |
| 181 |
:target: ../_images/guinier_overview_jacques.png |
| 182 |
|
| 183 |
Figure 3 from [2]. A and D show a good (monodisperse) scattering profile and |
| 184 |
Guinier fit. B and E show scattering profiles with varying degrees of |
| 185 |
interparticle interference. C and F show scattering profiles with varying |
| 186 |
degrees of aggregation. |
| 187 |
|
| 188 |
|
| 189 |
Aggregation |
| 190 |
************************* |
| 191 |
|
| 192 |
Aggregation causes a characteristic upturn at low q. This can either be caused by |
| 193 |
aggregates initially present in your sample, or by radiation induced aggregation |
| 194 |
(radiation damage). The figure below shows what that might look like in your data. |
| 195 |
|
| 196 |
.. figure:: images/guinier_aggregation_putnam.png |
| 197 |
:target: ../_images/guinier_aggregation_putnam.png |
| 198 |
|
| 199 |
Figure 23 from [3], showing no (left panel), large (middle panel) and small |
| 200 |
(right panel) amounts of aggregates seen in the Guinier fit. |
| 201 |
|
| 202 |
The effect of aggregation can also be clearly seen in the fit residual, where it |
| 203 |
shows up as a 'smile', with the residual above zero near the start and end of the |
| 204 |
fit and below zero in the middle. The figure below illustrates this. |
| 205 |
|
| 206 |
.. figure:: images/guinier_residual_aggregated.png |
| 207 |
:target: ../_images/guinier_residual_aggregated.png |
| 208 |
:height: 400 px |
| 209 |
|
| 210 |
For an aggregated sample, even with the worst low *q* values cut off from the |
| 211 |
fit, the residual (bottom plot) show the characteristic 'smile', rather than |
| 212 |
being flat and randomly distributed about zero. |
| 213 |
|
| 214 |
|
| 215 |
Repulsion |
| 216 |
************************* |
| 217 |
|
| 218 |
Repulsive interparticle interactions result in a structure factor that causes |
| 219 |
a downturn in the scattering profile at low q. This is typically caused by |
| 220 |
electrostatic interactions, and can often be remedied by either reducing the |
| 221 |
sample concentration or adding more salt to the buffer. These effects are |
| 222 |
also clearly seen in the fit residual, where it shows up as a 'frown', with the |
| 223 |
residual below zero near the start and end of the fit and above zero in the |
| 224 |
middle. This is shown in the figure below. |
| 225 |
|
| 226 |
.. figure:: images/guinier_residual_repulsion.png |
| 227 |
:target: ../_images/guinier_residual_repulsion.png |
| 228 |
:height: 400 px |
| 229 |
|
| 230 |
For a repulsive sample, the residual (bottom plot) show the characteristic |
| 231 |
'frown', rather than being flat and randomly distributed about zero. |
| 232 |
|
| 233 |
Note that the above figure is an extreme example of repulsion, the downward |
| 234 |
curve may not be that obvious. |
| 235 |
|
| 236 |
Bad buffer subtraction |
| 237 |
************************* |
| 238 |
|
| 239 |
Good SAXS data depends on subtracting away all scattering from the buffer and |
| 240 |
instrument background. If this subtraction is not good, you can end up with |
| 241 |
a downturn at low q (over subtraction) or an upturn at low q (under subtraction). |
| 242 |
This will look similar to aggregation or repulsion in the Guinier fit. |
| 243 |
|
| 244 |
|
| 245 |
FAQ |
| 246 |
^^^^^^^^ |
| 247 |
|
| 248 |
What if I don't know my particle shape, should I fit to a maximum |qRg| 1.3 or 1.0? |
| 249 |
************************************************************************************* |
| 250 |
|
| 251 |
Very often, you don't know what your particle shape is before making a SAXS measurement |
| 252 |
(in fact, this is often one of the purposes of a SAXS measurement). In that case, |
| 253 |
start out by fitting to a maximum |qRg| of 1.3. If that has a non-flat residual, |
| 254 |
reduce the fitting range to a maximum |qRg| of 1.0. If the residual becomes |
| 255 |
flat upon reducing the maximum |qRg|, then your particle is likely more |
| 256 |
extended than globular, and you should keep the maximum |qRg| at 1.0. If reducing |
| 257 |
the maximum |qRg| still leaves a non-flat residual, your data is showing signs |
| 258 |
of aggregation, repulsion, or some other issue. |
| 259 |
|
| 260 |
My Guinier fit isn't great, can I still use my data? |
| 261 |
****************************************************** |
| 262 |
|
| 263 |
If your Guinier fit isn't great, typically you shouldn't use the data. Even small |
| 264 |
amounts of aggregation (<1%) can affect things like the measured maximum dimension, |
| 265 |
and three dimensional reconstructions. While data with imperfect Guinier fits |
| 266 |
can be used in some specific cases, my general recommendation is to collect the |
| 267 |
data again. |
| 268 |
|
| 269 |
My Guinier fit is a bit off, how can I fix it? |
| 270 |
************************************************** |
| 271 |
|
| 272 |
If your Guinier fit isn't ideal, typically the only way to fix this is to |
| 273 |
collect the data again, improving your sample/solution conditions. Below are |
| 274 |
a few things you can try to fix these issues. |
| 275 |
|
| 276 |
For inherent aggregation: |
| 277 |
|
| 278 |
#. Spin down your sample in a centrifuge at high speeds (~16000 g) for 5-10 |
| 279 |
minutes before data collection. In some cases, ultracentrifugation may help. |
| 280 |
|
| 281 |
#. Use size exclusion chromatography coupled to SAXS instead of batch mode SAXS |
| 282 |
for in-line sample purification. |
| 283 |
|
| 284 |
#. Reduce the concentration of your sample. |
| 285 |
|
| 286 |
#. Re-purify your sample using size exclusion or ion exchange chromatography |
| 287 |
immediately before the SAXS measurement. |
| 288 |
|
| 289 |
For radiation damage (often aggregation): |
| 290 |
|
| 291 |
#. Add 1-5% glycerol. |
| 292 |
|
| 293 |
#. Increase the flow/oscillation speed of your sample. |
| 294 |
|
| 295 |
#. Reduce the exposure time and/or number of exposures. |
| 296 |
|
| 297 |
#. Add radical scavengers like DTT. |
| 298 |
|
| 299 |
#. Attenuate the incident x-ray beam. |
| 300 |
|
| 301 |
For repulsion: |
| 302 |
|
| 303 |
#. Add salt to the buffer to reduce repulsion. |
| 304 |
|
| 305 |
#. Reduce the concentration of your sample. |
| 306 |
|
| 307 |
#. Change the pH of your buffer. |
| 308 |
|
| 309 |
For bad buffer subtraction: |
| 310 |
|
| 311 |
#. Prepare matching buffer using dialysis. |
| 312 |
|
| 313 |
#. Exchange buffer across a sizing column or desalting column. |
| 314 |
|
| 315 |
|
| 316 |
|
| 317 |
References |
| 318 |
^^^^^^^^^^^^ |
| 319 |
1. `Feigin, L., Svergun, Structure Analysis by Small-Angle X-ray and Neutron Scattering (1987). |
| 320 |
<https://www.embl-hamburg.de/biosaxs/reprints/feigin_svergun_1987.pdf>`_ |
| 321 |
|
| 322 |
2. Jacques, D. A. & Trewhella, J. (2010). Protein Sci. 19, 642–657. |
| 323 |
DOI: `10.1002/pro.35 <https://doi.org/10.1002/pro.351>`_ |
| 324 |
|
| 325 |
3. Putnam, C. D., Hammel, M., Hura, G. L. & Tainer, J. a (2007). Q. Rev. |
| 326 |
Biophys. 40, 191–285. DOI: `10.1017/S0033583507004635 |
| 327 |
<https://doi.org/10.1017/S0033583507004635>`_ |
| 328 |
|
| 329 |
.. |Rg| replace:: R\ :sub:`g` |
| 330 |
|
| 331 |
.. |qRg| replace:: qR\ :sub:`g` |
| 332 |
|