| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* This file is part of wl1251 |
| 4 |
* |
| 5 |
* Copyright (C) 2008-2009 Nokia Corporation |
| 6 |
*/ |
| 7 |
|
| 8 |
#include <linux/module.h> |
| 9 |
#include <linux/interrupt.h> |
| 10 |
#include <linux/firmware.h> |
| 11 |
#include <linux/delay.h> |
| 12 |
#include <linux/irq.h> |
| 13 |
#include <linux/crc32.h> |
| 14 |
#include <linux/etherdevice.h> |
| 15 |
#include <linux/vmalloc.h> |
| 16 |
#include <linux/slab.h> |
| 17 |
#include <linux/netdevice.h> |
| 18 |
|
| 19 |
#include "wl1251.h" |
| 20 |
#include "wl12xx_80211.h" |
| 21 |
#include "reg.h" |
| 22 |
#include "io.h" |
| 23 |
#include "cmd.h" |
| 24 |
#include "event.h" |
| 25 |
#include "tx.h" |
| 26 |
#include "rx.h" |
| 27 |
#include "ps.h" |
| 28 |
#include "init.h" |
| 29 |
#include "debugfs.h" |
| 30 |
#include "boot.h" |
| 31 |
|
| 32 |
void wl1251_enable_interrupts(struct wl1251 *wl) |
| 33 |
{ |
| 34 |
wl->if_ops->enable_irq(wl); |
| 35 |
} |
| 36 |
|
| 37 |
void wl1251_disable_interrupts(struct wl1251 *wl) |
| 38 |
{ |
| 39 |
wl->if_ops->disable_irq(wl); |
| 40 |
} |
| 41 |
|
| 42 |
static int wl1251_power_off(struct wl1251 *wl) |
| 43 |
{ |
| 44 |
return wl->if_ops->power(wl, false); |
| 45 |
} |
| 46 |
|
| 47 |
static int wl1251_power_on(struct wl1251 *wl) |
| 48 |
{ |
| 49 |
return wl->if_ops->power(wl, true); |
| 50 |
} |
| 51 |
|
| 52 |
static int wl1251_fetch_firmware(struct wl1251 *wl) |
| 53 |
{ |
| 54 |
const struct firmware *fw; |
| 55 |
struct device *dev = wiphy_dev(wl->hw->wiphy); |
| 56 |
int ret; |
| 57 |
|
| 58 |
ret = request_firmware(&fw, WL1251_FW_NAME, dev); |
| 59 |
|
| 60 |
if (ret < 0) { |
| 61 |
wl1251_error("could not get firmware: %d", ret); |
| 62 |
return ret; |
| 63 |
} |
| 64 |
|
| 65 |
if (fw->size % 4) { |
| 66 |
wl1251_error("firmware size is not multiple of 32 bits: %zu", |
| 67 |
fw->size); |
| 68 |
ret = -EILSEQ; |
| 69 |
goto out; |
| 70 |
} |
| 71 |
|
| 72 |
wl->fw_len = fw->size; |
| 73 |
wl->fw = vmalloc(wl->fw_len); |
| 74 |
|
| 75 |
if (!wl->fw) { |
| 76 |
wl1251_error("could not allocate memory for the firmware"); |
| 77 |
ret = -ENOMEM; |
| 78 |
goto out; |
| 79 |
} |
| 80 |
|
| 81 |
memcpy(wl->fw, fw->data, wl->fw_len); |
| 82 |
|
| 83 |
ret = 0; |
| 84 |
|
| 85 |
out: |
| 86 |
release_firmware(fw); |
| 87 |
|
| 88 |
return ret; |
| 89 |
} |
| 90 |
|
| 91 |
static int wl1251_fetch_nvs(struct wl1251 *wl) |
| 92 |
{ |
| 93 |
const struct firmware *fw; |
| 94 |
struct device *dev = wiphy_dev(wl->hw->wiphy); |
| 95 |
int ret; |
| 96 |
|
| 97 |
ret = request_firmware(&fw, WL1251_NVS_NAME, dev); |
| 98 |
|
| 99 |
if (ret < 0) { |
| 100 |
wl1251_error("could not get nvs file: %d", ret); |
| 101 |
return ret; |
| 102 |
} |
| 103 |
|
| 104 |
if (fw->size % 4) { |
| 105 |
wl1251_error("nvs size is not multiple of 32 bits: %zu", |
| 106 |
fw->size); |
| 107 |
ret = -EILSEQ; |
| 108 |
goto out; |
| 109 |
} |
| 110 |
|
| 111 |
wl->nvs = kmemdup(fw->data, fw->size, GFP_KERNEL); |
| 112 |
|
| 113 |
if (!wl->nvs) { |
| 114 |
wl1251_error("could not allocate memory for the nvs file"); |
| 115 |
ret = -ENOMEM; |
| 116 |
goto out; |
| 117 |
} |
| 118 |
|
| 119 |
wl->nvs_len = fw->size; |
| 120 |
|
| 121 |
ret = 0; |
| 122 |
|
| 123 |
out: |
| 124 |
release_firmware(fw); |
| 125 |
|
| 126 |
return ret; |
| 127 |
} |
| 128 |
|
| 129 |
static void wl1251_fw_wakeup(struct wl1251 *wl) |
| 130 |
{ |
| 131 |
u32 elp_reg; |
| 132 |
|
| 133 |
elp_reg = ELPCTRL_WAKE_UP; |
| 134 |
wl1251_write_elp(wl, HW_ACCESS_ELP_CTRL_REG_ADDR, elp_reg); |
| 135 |
elp_reg = wl1251_read_elp(wl, HW_ACCESS_ELP_CTRL_REG_ADDR); |
| 136 |
|
| 137 |
if (!(elp_reg & ELPCTRL_WLAN_READY)) |
| 138 |
wl1251_warning("WLAN not ready"); |
| 139 |
} |
| 140 |
|
| 141 |
static int wl1251_chip_wakeup(struct wl1251 *wl) |
| 142 |
{ |
| 143 |
int ret; |
| 144 |
|
| 145 |
ret = wl1251_power_on(wl); |
| 146 |
if (ret < 0) |
| 147 |
return ret; |
| 148 |
|
| 149 |
msleep(WL1251_POWER_ON_SLEEP); |
| 150 |
wl->if_ops->reset(wl); |
| 151 |
|
| 152 |
/* We don't need a real memory partition here, because we only want |
| 153 |
* to use the registers at this point. */ |
| 154 |
wl1251_set_partition(wl, |
| 155 |
0x00000000, |
| 156 |
0x00000000, |
| 157 |
REGISTERS_BASE, |
| 158 |
REGISTERS_DOWN_SIZE); |
| 159 |
|
| 160 |
/* ELP module wake up */ |
| 161 |
wl1251_fw_wakeup(wl); |
| 162 |
|
| 163 |
/* whal_FwCtrl_BootSm() */ |
| 164 |
|
| 165 |
/* 0. read chip id from CHIP_ID */ |
| 166 |
wl->chip_id = wl1251_reg_read32(wl, CHIP_ID_B); |
| 167 |
|
| 168 |
/* 1. check if chip id is valid */ |
| 169 |
|
| 170 |
switch (wl->chip_id) { |
| 171 |
case CHIP_ID_1251_PG12: |
| 172 |
wl1251_debug(DEBUG_BOOT, "chip id 0x%x (1251 PG12)", |
| 173 |
wl->chip_id); |
| 174 |
break; |
| 175 |
case CHIP_ID_1251_PG11: |
| 176 |
wl1251_debug(DEBUG_BOOT, "chip id 0x%x (1251 PG11)", |
| 177 |
wl->chip_id); |
| 178 |
break; |
| 179 |
case CHIP_ID_1251_PG10: |
| 180 |
default: |
| 181 |
wl1251_error("unsupported chip id: 0x%x", wl->chip_id); |
| 182 |
ret = -ENODEV; |
| 183 |
goto out; |
| 184 |
} |
| 185 |
|
| 186 |
if (wl->fw == NULL) { |
| 187 |
ret = wl1251_fetch_firmware(wl); |
| 188 |
if (ret < 0) |
| 189 |
goto out; |
| 190 |
} |
| 191 |
|
| 192 |
out: |
| 193 |
return ret; |
| 194 |
} |
| 195 |
|
| 196 |
#define WL1251_IRQ_LOOP_COUNT 10 |
| 197 |
static void wl1251_irq_work(struct work_struct *work) |
| 198 |
{ |
| 199 |
u32 intr, ctr = WL1251_IRQ_LOOP_COUNT; |
| 200 |
struct wl1251 *wl = |
| 201 |
container_of(work, struct wl1251, irq_work); |
| 202 |
int ret; |
| 203 |
|
| 204 |
mutex_lock(&wl->mutex); |
| 205 |
|
| 206 |
wl1251_debug(DEBUG_IRQ, "IRQ work"); |
| 207 |
|
| 208 |
if (wl->state == WL1251_STATE_OFF) |
| 209 |
goto out; |
| 210 |
|
| 211 |
ret = wl1251_ps_elp_wakeup(wl); |
| 212 |
if (ret < 0) |
| 213 |
goto out; |
| 214 |
|
| 215 |
wl1251_reg_write32(wl, ACX_REG_INTERRUPT_MASK, WL1251_ACX_INTR_ALL); |
| 216 |
|
| 217 |
intr = wl1251_reg_read32(wl, ACX_REG_INTERRUPT_CLEAR); |
| 218 |
wl1251_debug(DEBUG_IRQ, "intr: 0x%x", intr); |
| 219 |
|
| 220 |
do { |
| 221 |
if (wl->data_path) { |
| 222 |
wl->rx_counter = wl1251_mem_read32( |
| 223 |
wl, wl->data_path->rx_control_addr); |
| 224 |
|
| 225 |
/* We handle a frmware bug here */ |
| 226 |
switch ((wl->rx_counter - wl->rx_handled) & 0xf) { |
| 227 |
case 0: |
| 228 |
wl1251_debug(DEBUG_IRQ, |
| 229 |
"RX: FW and host in sync"); |
| 230 |
intr &= ~WL1251_ACX_INTR_RX0_DATA; |
| 231 |
intr &= ~WL1251_ACX_INTR_RX1_DATA; |
| 232 |
break; |
| 233 |
case 1: |
| 234 |
wl1251_debug(DEBUG_IRQ, "RX: FW +1"); |
| 235 |
intr |= WL1251_ACX_INTR_RX0_DATA; |
| 236 |
intr &= ~WL1251_ACX_INTR_RX1_DATA; |
| 237 |
break; |
| 238 |
case 2: |
| 239 |
wl1251_debug(DEBUG_IRQ, "RX: FW +2"); |
| 240 |
intr |= WL1251_ACX_INTR_RX0_DATA; |
| 241 |
intr |= WL1251_ACX_INTR_RX1_DATA; |
| 242 |
break; |
| 243 |
default: |
| 244 |
wl1251_warning( |
| 245 |
"RX: FW and host out of sync: %d", |
| 246 |
wl->rx_counter - wl->rx_handled); |
| 247 |
break; |
| 248 |
} |
| 249 |
|
| 250 |
wl->rx_handled = wl->rx_counter; |
| 251 |
|
| 252 |
wl1251_debug(DEBUG_IRQ, "RX counter: %d", |
| 253 |
wl->rx_counter); |
| 254 |
} |
| 255 |
|
| 256 |
intr &= wl->intr_mask; |
| 257 |
|
| 258 |
if (intr == 0) { |
| 259 |
wl1251_debug(DEBUG_IRQ, "INTR is 0"); |
| 260 |
goto out_sleep; |
| 261 |
} |
| 262 |
|
| 263 |
if (intr & WL1251_ACX_INTR_RX0_DATA) { |
| 264 |
wl1251_debug(DEBUG_IRQ, "WL1251_ACX_INTR_RX0_DATA"); |
| 265 |
wl1251_rx(wl); |
| 266 |
} |
| 267 |
|
| 268 |
if (intr & WL1251_ACX_INTR_RX1_DATA) { |
| 269 |
wl1251_debug(DEBUG_IRQ, "WL1251_ACX_INTR_RX1_DATA"); |
| 270 |
wl1251_rx(wl); |
| 271 |
} |
| 272 |
|
| 273 |
if (intr & WL1251_ACX_INTR_TX_RESULT) { |
| 274 |
wl1251_debug(DEBUG_IRQ, "WL1251_ACX_INTR_TX_RESULT"); |
| 275 |
wl1251_tx_complete(wl); |
| 276 |
} |
| 277 |
|
| 278 |
if (intr & WL1251_ACX_INTR_EVENT_A) { |
| 279 |
wl1251_debug(DEBUG_IRQ, "WL1251_ACX_INTR_EVENT_A"); |
| 280 |
wl1251_event_handle(wl, 0); |
| 281 |
} |
| 282 |
|
| 283 |
if (intr & WL1251_ACX_INTR_EVENT_B) { |
| 284 |
wl1251_debug(DEBUG_IRQ, "WL1251_ACX_INTR_EVENT_B"); |
| 285 |
wl1251_event_handle(wl, 1); |
| 286 |
} |
| 287 |
|
| 288 |
if (intr & WL1251_ACX_INTR_INIT_COMPLETE) |
| 289 |
wl1251_debug(DEBUG_IRQ, |
| 290 |
"WL1251_ACX_INTR_INIT_COMPLETE"); |
| 291 |
|
| 292 |
if (--ctr == 0) |
| 293 |
break; |
| 294 |
|
| 295 |
intr = wl1251_reg_read32(wl, ACX_REG_INTERRUPT_CLEAR); |
| 296 |
} while (intr); |
| 297 |
|
| 298 |
out_sleep: |
| 299 |
wl1251_reg_write32(wl, ACX_REG_INTERRUPT_MASK, ~(wl->intr_mask)); |
| 300 |
wl1251_ps_elp_sleep(wl); |
| 301 |
|
| 302 |
out: |
| 303 |
mutex_unlock(&wl->mutex); |
| 304 |
} |
| 305 |
|
| 306 |
static int wl1251_join(struct wl1251 *wl, u8 bss_type, u8 channel, |
| 307 |
u16 beacon_interval, u8 dtim_period) |
| 308 |
{ |
| 309 |
int ret; |
| 310 |
|
| 311 |
ret = wl1251_acx_frame_rates(wl, DEFAULT_HW_GEN_TX_RATE, |
| 312 |
DEFAULT_HW_GEN_MODULATION_TYPE, |
| 313 |
wl->tx_mgmt_frm_rate, |
| 314 |
wl->tx_mgmt_frm_mod); |
| 315 |
if (ret < 0) |
| 316 |
goto out; |
| 317 |
|
| 318 |
/* |
| 319 |
* Join command applies filters, and if we are not associated, |
| 320 |
* BSSID filter must be disabled for association to work. |
| 321 |
*/ |
| 322 |
if (is_zero_ether_addr(wl->bssid)) |
| 323 |
wl->rx_config &= ~CFG_BSSID_FILTER_EN; |
| 324 |
|
| 325 |
ret = wl1251_cmd_join(wl, bss_type, channel, beacon_interval, |
| 326 |
dtim_period); |
| 327 |
if (ret < 0) |
| 328 |
goto out; |
| 329 |
|
| 330 |
ret = wl1251_event_wait(wl, JOIN_EVENT_COMPLETE_ID, 100); |
| 331 |
if (ret < 0) |
| 332 |
wl1251_warning("join timeout"); |
| 333 |
|
| 334 |
out: |
| 335 |
return ret; |
| 336 |
} |
| 337 |
|
| 338 |
static void wl1251_op_tx(struct ieee80211_hw *hw, |
| 339 |
struct ieee80211_tx_control *control, |
| 340 |
struct sk_buff *skb) |
| 341 |
{ |
| 342 |
struct wl1251 *wl = hw->priv; |
| 343 |
unsigned long flags; |
| 344 |
|
| 345 |
skb_queue_tail(&wl->tx_queue, skb); |
| 346 |
|
| 347 |
/* |
| 348 |
* The chip specific setup must run before the first TX packet - |
| 349 |
* before that, the tx_work will not be initialized! |
| 350 |
*/ |
| 351 |
|
| 352 |
ieee80211_queue_work(wl->hw, &wl->tx_work); |
| 353 |
|
| 354 |
/* |
| 355 |
* The workqueue is slow to process the tx_queue and we need stop |
| 356 |
* the queue here, otherwise the queue will get too long. |
| 357 |
*/ |
| 358 |
if (skb_queue_len(&wl->tx_queue) >= WL1251_TX_QUEUE_HIGH_WATERMARK) { |
| 359 |
wl1251_debug(DEBUG_TX, "op_tx: tx_queue full, stop queues"); |
| 360 |
|
| 361 |
spin_lock_irqsave(&wl->wl_lock, flags); |
| 362 |
ieee80211_stop_queues(wl->hw); |
| 363 |
wl->tx_queue_stopped = true; |
| 364 |
spin_unlock_irqrestore(&wl->wl_lock, flags); |
| 365 |
} |
| 366 |
} |
| 367 |
|
| 368 |
static int wl1251_op_start(struct ieee80211_hw *hw) |
| 369 |
{ |
| 370 |
struct wl1251 *wl = hw->priv; |
| 371 |
struct wiphy *wiphy = hw->wiphy; |
| 372 |
int ret = 0; |
| 373 |
|
| 374 |
wl1251_debug(DEBUG_MAC80211, "mac80211 start"); |
| 375 |
|
| 376 |
mutex_lock(&wl->mutex); |
| 377 |
|
| 378 |
if (wl->state != WL1251_STATE_OFF) { |
| 379 |
wl1251_error("cannot start because not in off state: %d", |
| 380 |
wl->state); |
| 381 |
ret = -EBUSY; |
| 382 |
goto out; |
| 383 |
} |
| 384 |
|
| 385 |
ret = wl1251_chip_wakeup(wl); |
| 386 |
if (ret < 0) |
| 387 |
goto out; |
| 388 |
|
| 389 |
ret = wl1251_boot(wl); |
| 390 |
if (ret < 0) |
| 391 |
goto out; |
| 392 |
|
| 393 |
ret = wl1251_hw_init(wl); |
| 394 |
if (ret < 0) |
| 395 |
goto out; |
| 396 |
|
| 397 |
ret = wl1251_acx_station_id(wl); |
| 398 |
if (ret < 0) |
| 399 |
goto out; |
| 400 |
|
| 401 |
wl->state = WL1251_STATE_ON; |
| 402 |
|
| 403 |
wl1251_info("firmware booted (%s)", wl->fw_ver); |
| 404 |
|
| 405 |
/* update hw/fw version info in wiphy struct */ |
| 406 |
wiphy->hw_version = wl->chip_id; |
| 407 |
strscpy(wiphy->fw_version, wl->fw_ver, sizeof(wiphy->fw_version)); |
| 408 |
|
| 409 |
out: |
| 410 |
if (ret < 0) |
| 411 |
wl1251_power_off(wl); |
| 412 |
|
| 413 |
mutex_unlock(&wl->mutex); |
| 414 |
|
| 415 |
return ret; |
| 416 |
} |
| 417 |
|
| 418 |
static void wl1251_op_stop(struct ieee80211_hw *hw, bool suspend) |
| 419 |
{ |
| 420 |
struct wl1251 *wl = hw->priv; |
| 421 |
|
| 422 |
wl1251_info("down"); |
| 423 |
|
| 424 |
wl1251_debug(DEBUG_MAC80211, "mac80211 stop"); |
| 425 |
|
| 426 |
mutex_lock(&wl->mutex); |
| 427 |
|
| 428 |
WARN_ON(wl->state != WL1251_STATE_ON); |
| 429 |
|
| 430 |
if (wl->scanning) { |
| 431 |
struct cfg80211_scan_info info = { |
| 432 |
.aborted = true, |
| 433 |
}; |
| 434 |
|
| 435 |
ieee80211_scan_completed(wl->hw, &info); |
| 436 |
wl->scanning = false; |
| 437 |
} |
| 438 |
|
| 439 |
wl->state = WL1251_STATE_OFF; |
| 440 |
|
| 441 |
wl1251_disable_interrupts(wl); |
| 442 |
|
| 443 |
mutex_unlock(&wl->mutex); |
| 444 |
|
| 445 |
cancel_work_sync(&wl->irq_work); |
| 446 |
cancel_work_sync(&wl->tx_work); |
| 447 |
cancel_delayed_work_sync(&wl->elp_work); |
| 448 |
|
| 449 |
mutex_lock(&wl->mutex); |
| 450 |
|
| 451 |
/* let's notify MAC80211 about the remaining pending TX frames */ |
| 452 |
wl1251_tx_flush(wl); |
| 453 |
wl1251_power_off(wl); |
| 454 |
|
| 455 |
eth_zero_addr(wl->bssid); |
| 456 |
wl->listen_int = 1; |
| 457 |
wl->bss_type = MAX_BSS_TYPE; |
| 458 |
|
| 459 |
wl->data_in_count = 0; |
| 460 |
wl->rx_counter = 0; |
| 461 |
wl->rx_handled = 0; |
| 462 |
wl->rx_current_buffer = 0; |
| 463 |
wl->rx_last_id = 0; |
| 464 |
wl->next_tx_complete = 0; |
| 465 |
wl->elp = false; |
| 466 |
wl->station_mode = STATION_ACTIVE_MODE; |
| 467 |
wl->psm_entry_retry = 0; |
| 468 |
wl->tx_queue_stopped = false; |
| 469 |
wl->power_level = WL1251_DEFAULT_POWER_LEVEL; |
| 470 |
wl->rssi_thold = 0; |
| 471 |
wl->channel = WL1251_DEFAULT_CHANNEL; |
| 472 |
wl->monitor_present = false; |
| 473 |
wl->joined = false; |
| 474 |
|
| 475 |
wl1251_debugfs_reset(wl); |
| 476 |
|
| 477 |
mutex_unlock(&wl->mutex); |
| 478 |
} |
| 479 |
|
| 480 |
static int wl1251_op_add_interface(struct ieee80211_hw *hw, |
| 481 |
struct ieee80211_vif *vif) |
| 482 |
{ |
| 483 |
struct wl1251 *wl = hw->priv; |
| 484 |
int ret = 0; |
| 485 |
|
| 486 |
vif->driver_flags |= IEEE80211_VIF_BEACON_FILTER | |
| 487 |
IEEE80211_VIF_SUPPORTS_UAPSD | |
| 488 |
IEEE80211_VIF_SUPPORTS_CQM_RSSI; |
| 489 |
|
| 490 |
wl1251_debug(DEBUG_MAC80211, "mac80211 add interface type %d mac %pM", |
| 491 |
vif->type, vif->addr); |
| 492 |
|
| 493 |
mutex_lock(&wl->mutex); |
| 494 |
if (wl->vif) { |
| 495 |
ret = -EBUSY; |
| 496 |
goto out; |
| 497 |
} |
| 498 |
|
| 499 |
wl->vif = vif; |
| 500 |
|
| 501 |
switch (vif->type) { |
| 502 |
case NL80211_IFTYPE_STATION: |
| 503 |
wl->bss_type = BSS_TYPE_STA_BSS; |
| 504 |
break; |
| 505 |
case NL80211_IFTYPE_ADHOC: |
| 506 |
wl->bss_type = BSS_TYPE_IBSS; |
| 507 |
break; |
| 508 |
default: |
| 509 |
ret = -EOPNOTSUPP; |
| 510 |
goto out; |
| 511 |
} |
| 512 |
|
| 513 |
if (!ether_addr_equal_unaligned(wl->mac_addr, vif->addr)) { |
| 514 |
memcpy(wl->mac_addr, vif->addr, ETH_ALEN); |
| 515 |
SET_IEEE80211_PERM_ADDR(wl->hw, wl->mac_addr); |
| 516 |
ret = wl1251_acx_station_id(wl); |
| 517 |
if (ret < 0) |
| 518 |
goto out; |
| 519 |
} |
| 520 |
|
| 521 |
out: |
| 522 |
mutex_unlock(&wl->mutex); |
| 523 |
return ret; |
| 524 |
} |
| 525 |
|
| 526 |
static void wl1251_op_remove_interface(struct ieee80211_hw *hw, |
| 527 |
struct ieee80211_vif *vif) |
| 528 |
{ |
| 529 |
struct wl1251 *wl = hw->priv; |
| 530 |
|
| 531 |
mutex_lock(&wl->mutex); |
| 532 |
wl1251_debug(DEBUG_MAC80211, "mac80211 remove interface"); |
| 533 |
wl->vif = NULL; |
| 534 |
eth_zero_addr(wl->bssid); |
| 535 |
mutex_unlock(&wl->mutex); |
| 536 |
} |
| 537 |
|
| 538 |
static int wl1251_build_null_data(struct wl1251 *wl) |
| 539 |
{ |
| 540 |
struct sk_buff *skb = NULL; |
| 541 |
int size; |
| 542 |
void *ptr; |
| 543 |
int ret = -ENOMEM; |
| 544 |
|
| 545 |
if (wl->bss_type == BSS_TYPE_IBSS) { |
| 546 |
size = sizeof(struct wl12xx_null_data_template); |
| 547 |
ptr = NULL; |
| 548 |
} else { |
| 549 |
skb = ieee80211_nullfunc_get(wl->hw, wl->vif, -1, false); |
| 550 |
if (!skb) |
| 551 |
goto out; |
| 552 |
size = skb->len; |
| 553 |
ptr = skb->data; |
| 554 |
} |
| 555 |
|
| 556 |
ret = wl1251_cmd_template_set(wl, CMD_NULL_DATA, ptr, size); |
| 557 |
|
| 558 |
out: |
| 559 |
dev_kfree_skb(skb); |
| 560 |
if (ret) |
| 561 |
wl1251_warning("cmd build null data failed: %d", ret); |
| 562 |
|
| 563 |
return ret; |
| 564 |
} |
| 565 |
|
| 566 |
static int wl1251_build_qos_null_data(struct wl1251 *wl) |
| 567 |
{ |
| 568 |
struct ieee80211_qos_hdr template; |
| 569 |
|
| 570 |
memset(&template, 0, sizeof(template)); |
| 571 |
|
| 572 |
memcpy(template.addr1, wl->bssid, ETH_ALEN); |
| 573 |
memcpy(template.addr2, wl->mac_addr, ETH_ALEN); |
| 574 |
memcpy(template.addr3, wl->bssid, ETH_ALEN); |
| 575 |
|
| 576 |
template.frame_control = cpu_to_le16(IEEE80211_FTYPE_DATA | |
| 577 |
IEEE80211_STYPE_QOS_NULLFUNC | |
| 578 |
IEEE80211_FCTL_TODS); |
| 579 |
|
| 580 |
/* FIXME: not sure what priority to use here */ |
| 581 |
template.qos_ctrl = cpu_to_le16(0); |
| 582 |
|
| 583 |
return wl1251_cmd_template_set(wl, CMD_QOS_NULL_DATA, &template, |
| 584 |
sizeof(template)); |
| 585 |
} |
| 586 |
|
| 587 |
static bool wl1251_can_do_pm(struct ieee80211_conf *conf, struct wl1251 *wl) |
| 588 |
{ |
| 589 |
return (conf->flags & IEEE80211_CONF_PS) && !wl->monitor_present; |
| 590 |
} |
| 591 |
|
| 592 |
static int wl1251_op_config(struct ieee80211_hw *hw, int radio_idx, u32 changed) |
| 593 |
{ |
| 594 |
struct wl1251 *wl = hw->priv; |
| 595 |
struct ieee80211_conf *conf = &hw->conf; |
| 596 |
int channel, ret = 0; |
| 597 |
|
| 598 |
channel = ieee80211_frequency_to_channel( |
| 599 |
conf->chandef.chan->center_freq); |
| 600 |
|
| 601 |
wl1251_debug(DEBUG_MAC80211, |
| 602 |
"mac80211 config ch %d monitor %s psm %s power %d", |
| 603 |
channel, |
| 604 |
conf->flags & IEEE80211_CONF_MONITOR ? "on" : "off", |
| 605 |
conf->flags & IEEE80211_CONF_PS ? "on" : "off", |
| 606 |
conf->power_level); |
| 607 |
|
| 608 |
mutex_lock(&wl->mutex); |
| 609 |
|
| 610 |
ret = wl1251_ps_elp_wakeup(wl); |
| 611 |
if (ret < 0) |
| 612 |
goto out; |
| 613 |
|
| 614 |
if (changed & IEEE80211_CONF_CHANGE_MONITOR) { |
| 615 |
u32 mode; |
| 616 |
|
| 617 |
if (conf->flags & IEEE80211_CONF_MONITOR) { |
| 618 |
wl->monitor_present = true; |
| 619 |
mode = DF_SNIFF_MODE_ENABLE | DF_ENCRYPTION_DISABLE; |
| 620 |
} else { |
| 621 |
wl->monitor_present = false; |
| 622 |
mode = 0; |
| 623 |
} |
| 624 |
|
| 625 |
ret = wl1251_acx_feature_cfg(wl, mode); |
| 626 |
if (ret < 0) |
| 627 |
goto out_sleep; |
| 628 |
} |
| 629 |
|
| 630 |
if (channel != wl->channel) { |
| 631 |
wl->channel = channel; |
| 632 |
|
| 633 |
/* |
| 634 |
* Use ENABLE_RX command for channel switching when no |
| 635 |
* interface is present (monitor mode only). |
| 636 |
* This leaves the tx path disabled in firmware, whereas |
| 637 |
* the usual JOIN command seems to transmit some frames |
| 638 |
* at firmware level. |
| 639 |
*/ |
| 640 |
if (wl->vif == NULL) { |
| 641 |
wl->joined = false; |
| 642 |
ret = wl1251_cmd_data_path_rx(wl, wl->channel, 1); |
| 643 |
} else { |
| 644 |
ret = wl1251_join(wl, wl->bss_type, wl->channel, |
| 645 |
wl->beacon_int, wl->dtim_period); |
| 646 |
} |
| 647 |
if (ret < 0) |
| 648 |
goto out_sleep; |
| 649 |
} |
| 650 |
|
| 651 |
if (wl1251_can_do_pm(conf, wl) && !wl->psm_requested) { |
| 652 |
wl1251_debug(DEBUG_PSM, "psm enabled"); |
| 653 |
|
| 654 |
wl->psm_requested = true; |
| 655 |
|
| 656 |
wl->dtim_period = conf->ps_dtim_period; |
| 657 |
|
| 658 |
ret = wl1251_acx_wr_tbtt_and_dtim(wl, wl->beacon_int, |
| 659 |
wl->dtim_period); |
| 660 |
|
| 661 |
/* |
| 662 |
* mac80211 enables PSM only if we're already associated. |
| 663 |
*/ |
| 664 |
ret = wl1251_ps_set_mode(wl, STATION_POWER_SAVE_MODE); |
| 665 |
if (ret < 0) |
| 666 |
goto out_sleep; |
| 667 |
} else if (!wl1251_can_do_pm(conf, wl) && wl->psm_requested) { |
| 668 |
wl1251_debug(DEBUG_PSM, "psm disabled"); |
| 669 |
|
| 670 |
wl->psm_requested = false; |
| 671 |
|
| 672 |
if (wl->station_mode != STATION_ACTIVE_MODE) { |
| 673 |
ret = wl1251_ps_set_mode(wl, STATION_ACTIVE_MODE); |
| 674 |
if (ret < 0) |
| 675 |
goto out_sleep; |
| 676 |
} |
| 677 |
} |
| 678 |
|
| 679 |
if (changed & IEEE80211_CONF_CHANGE_IDLE && !wl->scanning) { |
| 680 |
if (conf->flags & IEEE80211_CONF_IDLE) { |
| 681 |
ret = wl1251_ps_set_mode(wl, STATION_IDLE); |
| 682 |
if (ret < 0) |
| 683 |
goto out_sleep; |
| 684 |
} else { |
| 685 |
ret = wl1251_ps_set_mode(wl, STATION_ACTIVE_MODE); |
| 686 |
if (ret < 0) |
| 687 |
goto out_sleep; |
| 688 |
ret = wl1251_join(wl, wl->bss_type, wl->channel, |
| 689 |
wl->beacon_int, wl->dtim_period); |
| 690 |
if (ret < 0) |
| 691 |
goto out_sleep; |
| 692 |
} |
| 693 |
} |
| 694 |
|
| 695 |
if (conf->power_level != wl->power_level) { |
| 696 |
ret = wl1251_acx_tx_power(wl, conf->power_level); |
| 697 |
if (ret < 0) |
| 698 |
goto out_sleep; |
| 699 |
|
| 700 |
wl->power_level = conf->power_level; |
| 701 |
} |
| 702 |
|
| 703 |
out_sleep: |
| 704 |
wl1251_ps_elp_sleep(wl); |
| 705 |
|
| 706 |
out: |
| 707 |
mutex_unlock(&wl->mutex); |
| 708 |
|
| 709 |
return ret; |
| 710 |
} |
| 711 |
|
| 712 |
struct wl1251_filter_params { |
| 713 |
bool enabled; |
| 714 |
int mc_list_length; |
| 715 |
u8 mc_list[ACX_MC_ADDRESS_GROUP_MAX][ETH_ALEN]; |
| 716 |
}; |
| 717 |
|
| 718 |
static u64 wl1251_op_prepare_multicast(struct ieee80211_hw *hw, |
| 719 |
struct netdev_hw_addr_list *mc_list) |
| 720 |
{ |
| 721 |
struct wl1251_filter_params *fp; |
| 722 |
struct netdev_hw_addr *ha; |
| 723 |
struct wl1251 *wl = hw->priv; |
| 724 |
|
| 725 |
if (unlikely(wl->state == WL1251_STATE_OFF)) |
| 726 |
return 0; |
| 727 |
|
| 728 |
fp = kzalloc_obj(*fp, GFP_ATOMIC); |
| 729 |
if (!fp) { |
| 730 |
wl1251_error("Out of memory setting filters."); |
| 731 |
return 0; |
| 732 |
} |
| 733 |
|
| 734 |
/* update multicast filtering parameters */ |
| 735 |
fp->mc_list_length = 0; |
| 736 |
if (netdev_hw_addr_list_count(mc_list) > ACX_MC_ADDRESS_GROUP_MAX) { |
| 737 |
fp->enabled = false; |
| 738 |
} else { |
| 739 |
fp->enabled = true; |
| 740 |
netdev_hw_addr_list_for_each(ha, mc_list) { |
| 741 |
memcpy(fp->mc_list[fp->mc_list_length], |
| 742 |
ha->addr, ETH_ALEN); |
| 743 |
fp->mc_list_length++; |
| 744 |
} |
| 745 |
} |
| 746 |
|
| 747 |
return (u64)(unsigned long)fp; |
| 748 |
} |
| 749 |
|
| 750 |
#define WL1251_SUPPORTED_FILTERS (FIF_ALLMULTI | \ |
| 751 |
FIF_FCSFAIL | \ |
| 752 |
FIF_BCN_PRBRESP_PROMISC | \ |
| 753 |
FIF_CONTROL | \ |
| 754 |
FIF_OTHER_BSS | \ |
| 755 |
FIF_PROBE_REQ) |
| 756 |
|
| 757 |
static void wl1251_op_configure_filter(struct ieee80211_hw *hw, |
| 758 |
unsigned int changed, |
| 759 |
unsigned int *total, u64 multicast) |
| 760 |
{ |
| 761 |
struct wl1251_filter_params *fp = (void *)(unsigned long)multicast; |
| 762 |
struct wl1251 *wl = hw->priv; |
| 763 |
int ret; |
| 764 |
|
| 765 |
wl1251_debug(DEBUG_MAC80211, "mac80211 configure filter"); |
| 766 |
|
| 767 |
*total &= WL1251_SUPPORTED_FILTERS; |
| 768 |
changed &= WL1251_SUPPORTED_FILTERS; |
| 769 |
|
| 770 |
if (changed == 0) { |
| 771 |
/* no filters which we support changed */ |
| 772 |
kfree(fp); |
| 773 |
return; |
| 774 |
} |
| 775 |
|
| 776 |
mutex_lock(&wl->mutex); |
| 777 |
|
| 778 |
wl->rx_config = WL1251_DEFAULT_RX_CONFIG; |
| 779 |
wl->rx_filter = WL1251_DEFAULT_RX_FILTER; |
| 780 |
|
| 781 |
if (*total & FIF_ALLMULTI) |
| 782 |
/* |
| 783 |
* CFG_MC_FILTER_EN in rx_config needs to be 0 to receive |
| 784 |
* all multicast frames |
| 785 |
*/ |
| 786 |
wl->rx_config &= ~CFG_MC_FILTER_EN; |
| 787 |
if (*total & FIF_FCSFAIL) |
| 788 |
wl->rx_filter |= CFG_RX_FCS_ERROR; |
| 789 |
if (*total & FIF_BCN_PRBRESP_PROMISC) { |
| 790 |
wl->rx_config &= ~CFG_BSSID_FILTER_EN; |
| 791 |
wl->rx_config &= ~CFG_SSID_FILTER_EN; |
| 792 |
} |
| 793 |
if (*total & FIF_CONTROL) |
| 794 |
wl->rx_filter |= CFG_RX_CTL_EN; |
| 795 |
if (*total & FIF_OTHER_BSS || is_zero_ether_addr(wl->bssid)) |
| 796 |
wl->rx_config &= ~CFG_BSSID_FILTER_EN; |
| 797 |
if (*total & FIF_PROBE_REQ) |
| 798 |
wl->rx_filter |= CFG_RX_PREQ_EN; |
| 799 |
|
| 800 |
if (wl->state == WL1251_STATE_OFF) |
| 801 |
goto out; |
| 802 |
|
| 803 |
ret = wl1251_ps_elp_wakeup(wl); |
| 804 |
if (ret < 0) |
| 805 |
goto out; |
| 806 |
|
| 807 |
if (*total & FIF_ALLMULTI) |
| 808 |
ret = wl1251_acx_group_address_tbl(wl, false, NULL, 0); |
| 809 |
else if (fp) |
| 810 |
ret = wl1251_acx_group_address_tbl(wl, fp->enabled, |
| 811 |
fp->mc_list, |
| 812 |
fp->mc_list_length); |
| 813 |
if (ret < 0) |
| 814 |
goto out; |
| 815 |
|
| 816 |
/* send filters to firmware */ |
| 817 |
wl1251_acx_rx_config(wl, wl->rx_config, wl->rx_filter); |
| 818 |
|
| 819 |
wl1251_ps_elp_sleep(wl); |
| 820 |
|
| 821 |
out: |
| 822 |
mutex_unlock(&wl->mutex); |
| 823 |
kfree(fp); |
| 824 |
} |
| 825 |
|
| 826 |
/* HW encryption */ |
| 827 |
static int wl1251_set_key_type(struct wl1251 *wl, |
| 828 |
struct wl1251_cmd_set_keys *key, |
| 829 |
enum set_key_cmd cmd, |
| 830 |
struct ieee80211_key_conf *mac80211_key, |
| 831 |
const u8 *addr) |
| 832 |
{ |
| 833 |
switch (mac80211_key->cipher) { |
| 834 |
case WLAN_CIPHER_SUITE_WEP40: |
| 835 |
case WLAN_CIPHER_SUITE_WEP104: |
| 836 |
if (is_broadcast_ether_addr(addr)) |
| 837 |
key->key_type = KEY_WEP_DEFAULT; |
| 838 |
else |
| 839 |
key->key_type = KEY_WEP_ADDR; |
| 840 |
|
| 841 |
mac80211_key->hw_key_idx = mac80211_key->keyidx; |
| 842 |
break; |
| 843 |
case WLAN_CIPHER_SUITE_TKIP: |
| 844 |
if (is_broadcast_ether_addr(addr)) |
| 845 |
key->key_type = KEY_TKIP_MIC_GROUP; |
| 846 |
else |
| 847 |
key->key_type = KEY_TKIP_MIC_PAIRWISE; |
| 848 |
|
| 849 |
mac80211_key->hw_key_idx = mac80211_key->keyidx; |
| 850 |
break; |
| 851 |
case WLAN_CIPHER_SUITE_CCMP: |
| 852 |
if (is_broadcast_ether_addr(addr)) |
| 853 |
key->key_type = KEY_AES_GROUP; |
| 854 |
else |
| 855 |
key->key_type = KEY_AES_PAIRWISE; |
| 856 |
mac80211_key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| 857 |
break; |
| 858 |
default: |
| 859 |
wl1251_error("Unknown key cipher 0x%x", mac80211_key->cipher); |
| 860 |
return -EOPNOTSUPP; |
| 861 |
} |
| 862 |
|
| 863 |
return 0; |
| 864 |
} |
| 865 |
|
| 866 |
static int wl1251_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, |
| 867 |
struct ieee80211_vif *vif, |
| 868 |
struct ieee80211_sta *sta, |
| 869 |
struct ieee80211_key_conf *key) |
| 870 |
{ |
| 871 |
struct wl1251 *wl = hw->priv; |
| 872 |
struct wl1251_cmd_set_keys *wl_cmd; |
| 873 |
const u8 *addr; |
| 874 |
int ret; |
| 875 |
|
| 876 |
static const u8 bcast_addr[ETH_ALEN] = |
| 877 |
{ 0xff, 0xff, 0xff, 0xff, 0xff, 0xff }; |
| 878 |
|
| 879 |
wl1251_debug(DEBUG_MAC80211, "mac80211 set key"); |
| 880 |
|
| 881 |
wl_cmd = kzalloc_obj(*wl_cmd); |
| 882 |
if (!wl_cmd) { |
| 883 |
ret = -ENOMEM; |
| 884 |
goto out; |
| 885 |
} |
| 886 |
|
| 887 |
addr = sta ? sta->addr : bcast_addr; |
| 888 |
|
| 889 |
wl1251_debug(DEBUG_CRYPT, "CMD: 0x%x", cmd); |
| 890 |
wl1251_dump(DEBUG_CRYPT, "ADDR: ", addr, ETH_ALEN); |
| 891 |
wl1251_debug(DEBUG_CRYPT, "Key: algo:0x%x, id:%d, len:%d flags 0x%x", |
| 892 |
key->cipher, key->keyidx, key->keylen, key->flags); |
| 893 |
wl1251_dump(DEBUG_CRYPT, "KEY: ", key->key, key->keylen); |
| 894 |
|
| 895 |
if (is_zero_ether_addr(addr)) { |
| 896 |
/* We dont support TX only encryption */ |
| 897 |
ret = -EOPNOTSUPP; |
| 898 |
goto out; |
| 899 |
} |
| 900 |
|
| 901 |
mutex_lock(&wl->mutex); |
| 902 |
|
| 903 |
switch (cmd) { |
| 904 |
case SET_KEY: |
| 905 |
if (wl->monitor_present) { |
| 906 |
ret = -EOPNOTSUPP; |
| 907 |
goto out_unlock; |
| 908 |
} |
| 909 |
wl_cmd->key_action = KEY_ADD_OR_REPLACE; |
| 910 |
break; |
| 911 |
case DISABLE_KEY: |
| 912 |
wl_cmd->key_action = KEY_REMOVE; |
| 913 |
break; |
| 914 |
default: |
| 915 |
wl1251_error("Unsupported key cmd 0x%x", cmd); |
| 916 |
break; |
| 917 |
} |
| 918 |
|
| 919 |
ret = wl1251_ps_elp_wakeup(wl); |
| 920 |
if (ret < 0) |
| 921 |
goto out_unlock; |
| 922 |
|
| 923 |
ret = wl1251_set_key_type(wl, wl_cmd, cmd, key, addr); |
| 924 |
if (ret < 0) { |
| 925 |
wl1251_error("Set KEY type failed"); |
| 926 |
goto out_sleep; |
| 927 |
} |
| 928 |
|
| 929 |
if (wl_cmd->key_type != KEY_WEP_DEFAULT) |
| 930 |
memcpy(wl_cmd->addr, addr, ETH_ALEN); |
| 931 |
|
| 932 |
if ((wl_cmd->key_type == KEY_TKIP_MIC_GROUP) || |
| 933 |
(wl_cmd->key_type == KEY_TKIP_MIC_PAIRWISE)) { |
| 934 |
/* |
| 935 |
* We get the key in the following form: |
| 936 |
* TKIP (16 bytes) - TX MIC (8 bytes) - RX MIC (8 bytes) |
| 937 |
* but the target is expecting: |
| 938 |
* TKIP - RX MIC - TX MIC |
| 939 |
*/ |
| 940 |
memcpy(wl_cmd->key, key->key, 16); |
| 941 |
memcpy(wl_cmd->key + 16, key->key + 24, 8); |
| 942 |
memcpy(wl_cmd->key + 24, key->key + 16, 8); |
| 943 |
|
| 944 |
} else { |
| 945 |
memcpy(wl_cmd->key, key->key, key->keylen); |
| 946 |
} |
| 947 |
wl_cmd->key_size = key->keylen; |
| 948 |
|
| 949 |
wl_cmd->id = key->keyidx; |
| 950 |
wl_cmd->ssid_profile = 0; |
| 951 |
|
| 952 |
wl1251_dump(DEBUG_CRYPT, "TARGET KEY: ", wl_cmd, sizeof(*wl_cmd)); |
| 953 |
|
| 954 |
ret = wl1251_cmd_send(wl, CMD_SET_KEYS, wl_cmd, sizeof(*wl_cmd)); |
| 955 |
if (ret < 0) { |
| 956 |
wl1251_warning("could not set keys"); |
| 957 |
goto out_sleep; |
| 958 |
} |
| 959 |
|
| 960 |
out_sleep: |
| 961 |
wl1251_ps_elp_sleep(wl); |
| 962 |
|
| 963 |
out_unlock: |
| 964 |
mutex_unlock(&wl->mutex); |
| 965 |
|
| 966 |
out: |
| 967 |
kfree(wl_cmd); |
| 968 |
|
| 969 |
return ret; |
| 970 |
} |
| 971 |
|
| 972 |
static int wl1251_op_hw_scan(struct ieee80211_hw *hw, |
| 973 |
struct ieee80211_vif *vif, |
| 974 |
struct ieee80211_scan_request *hw_req) |
| 975 |
{ |
| 976 |
struct cfg80211_scan_request *req = &hw_req->req; |
| 977 |
struct wl1251 *wl = hw->priv; |
| 978 |
struct sk_buff *skb; |
| 979 |
size_t ssid_len = 0; |
| 980 |
u8 *ssid = NULL; |
| 981 |
int ret; |
| 982 |
|
| 983 |
wl1251_debug(DEBUG_MAC80211, "mac80211 hw scan"); |
| 984 |
|
| 985 |
if (req->n_ssids) { |
| 986 |
ssid = req->ssids[0].ssid; |
| 987 |
ssid_len = req->ssids[0].ssid_len; |
| 988 |
} |
| 989 |
|
| 990 |
mutex_lock(&wl->mutex); |
| 991 |
|
| 992 |
if (wl->scanning) { |
| 993 |
wl1251_debug(DEBUG_SCAN, "scan already in progress"); |
| 994 |
ret = -EINVAL; |
| 995 |
goto out; |
| 996 |
} |
| 997 |
|
| 998 |
ret = wl1251_ps_elp_wakeup(wl); |
| 999 |
if (ret < 0) |
| 1000 |
goto out; |
| 1001 |
|
| 1002 |
if (hw->conf.flags & IEEE80211_CONF_IDLE) { |
| 1003 |
ret = wl1251_ps_set_mode(wl, STATION_ACTIVE_MODE); |
| 1004 |
if (ret < 0) |
| 1005 |
goto out_sleep; |
| 1006 |
ret = wl1251_join(wl, wl->bss_type, wl->channel, |
| 1007 |
wl->beacon_int, wl->dtim_period); |
| 1008 |
if (ret < 0) |
| 1009 |
goto out_sleep; |
| 1010 |
} |
| 1011 |
|
| 1012 |
skb = ieee80211_probereq_get(wl->hw, wl->vif->addr, ssid, ssid_len, |
| 1013 |
req->ie_len); |
| 1014 |
if (!skb) { |
| 1015 |
ret = -ENOMEM; |
| 1016 |
goto out_idle; |
| 1017 |
} |
| 1018 |
if (req->ie_len) |
| 1019 |
skb_put_data(skb, req->ie, req->ie_len); |
| 1020 |
|
| 1021 |
ret = wl1251_cmd_template_set(wl, CMD_PROBE_REQ, skb->data, |
| 1022 |
skb->len); |
| 1023 |
dev_kfree_skb(skb); |
| 1024 |
if (ret < 0) |
| 1025 |
goto out_idle; |
| 1026 |
|
| 1027 |
ret = wl1251_cmd_trigger_scan_to(wl, 0); |
| 1028 |
if (ret < 0) |
| 1029 |
goto out_idle; |
| 1030 |
|
| 1031 |
wl->scanning = true; |
| 1032 |
|
| 1033 |
ret = wl1251_cmd_scan(wl, ssid, ssid_len, req->channels, |
| 1034 |
req->n_channels, WL1251_SCAN_NUM_PROBES); |
| 1035 |
if (ret < 0) { |
| 1036 |
wl1251_debug(DEBUG_SCAN, "scan failed %d", ret); |
| 1037 |
wl->scanning = false; |
| 1038 |
goto out_idle; |
| 1039 |
} |
| 1040 |
goto out_sleep; |
| 1041 |
|
| 1042 |
out_idle: |
| 1043 |
if (hw->conf.flags & IEEE80211_CONF_IDLE) |
| 1044 |
ret = wl1251_ps_set_mode(wl, STATION_IDLE); |
| 1045 |
out_sleep: |
| 1046 |
wl1251_ps_elp_sleep(wl); |
| 1047 |
|
| 1048 |
out: |
| 1049 |
mutex_unlock(&wl->mutex); |
| 1050 |
|
| 1051 |
return ret; |
| 1052 |
} |
| 1053 |
|
| 1054 |
static int wl1251_op_set_rts_threshold(struct ieee80211_hw *hw, int radio_idx, |
| 1055 |
u32 value) |
| 1056 |
{ |
| 1057 |
struct wl1251 *wl = hw->priv; |
| 1058 |
int ret; |
| 1059 |
|
| 1060 |
mutex_lock(&wl->mutex); |
| 1061 |
|
| 1062 |
ret = wl1251_ps_elp_wakeup(wl); |
| 1063 |
if (ret < 0) |
| 1064 |
goto out; |
| 1065 |
|
| 1066 |
ret = wl1251_acx_rts_threshold(wl, (u16) value); |
| 1067 |
if (ret < 0) |
| 1068 |
wl1251_warning("wl1251_op_set_rts_threshold failed: %d", ret); |
| 1069 |
|
| 1070 |
wl1251_ps_elp_sleep(wl); |
| 1071 |
|
| 1072 |
out: |
| 1073 |
mutex_unlock(&wl->mutex); |
| 1074 |
|
| 1075 |
return ret; |
| 1076 |
} |
| 1077 |
|
| 1078 |
static void wl1251_op_bss_info_changed(struct ieee80211_hw *hw, |
| 1079 |
struct ieee80211_vif *vif, |
| 1080 |
struct ieee80211_bss_conf *bss_conf, |
| 1081 |
u64 changed) |
| 1082 |
{ |
| 1083 |
struct wl1251 *wl = hw->priv; |
| 1084 |
struct sk_buff *beacon, *skb; |
| 1085 |
bool enable; |
| 1086 |
int ret; |
| 1087 |
|
| 1088 |
wl1251_debug(DEBUG_MAC80211, "mac80211 bss info changed"); |
| 1089 |
|
| 1090 |
mutex_lock(&wl->mutex); |
| 1091 |
|
| 1092 |
ret = wl1251_ps_elp_wakeup(wl); |
| 1093 |
if (ret < 0) |
| 1094 |
goto out; |
| 1095 |
|
| 1096 |
if (changed & BSS_CHANGED_CQM) { |
| 1097 |
ret = wl1251_acx_low_rssi(wl, bss_conf->cqm_rssi_thold, |
| 1098 |
WL1251_DEFAULT_LOW_RSSI_WEIGHT, |
| 1099 |
WL1251_DEFAULT_LOW_RSSI_DEPTH, |
| 1100 |
WL1251_ACX_LOW_RSSI_TYPE_EDGE); |
| 1101 |
if (ret < 0) |
| 1102 |
goto out; |
| 1103 |
wl->rssi_thold = bss_conf->cqm_rssi_thold; |
| 1104 |
} |
| 1105 |
|
| 1106 |
if ((changed & BSS_CHANGED_BSSID) && |
| 1107 |
memcmp(wl->bssid, bss_conf->bssid, ETH_ALEN)) { |
| 1108 |
memcpy(wl->bssid, bss_conf->bssid, ETH_ALEN); |
| 1109 |
|
| 1110 |
if (!is_zero_ether_addr(wl->bssid)) { |
| 1111 |
ret = wl1251_build_null_data(wl); |
| 1112 |
if (ret < 0) |
| 1113 |
goto out_sleep; |
| 1114 |
|
| 1115 |
ret = wl1251_build_qos_null_data(wl); |
| 1116 |
if (ret < 0) |
| 1117 |
goto out_sleep; |
| 1118 |
|
| 1119 |
ret = wl1251_join(wl, wl->bss_type, wl->channel, |
| 1120 |
wl->beacon_int, wl->dtim_period); |
| 1121 |
if (ret < 0) |
| 1122 |
goto out_sleep; |
| 1123 |
} |
| 1124 |
} |
| 1125 |
|
| 1126 |
if (changed & BSS_CHANGED_ASSOC) { |
| 1127 |
if (vif->cfg.assoc) { |
| 1128 |
wl->beacon_int = bss_conf->beacon_int; |
| 1129 |
|
| 1130 |
skb = ieee80211_pspoll_get(wl->hw, wl->vif); |
| 1131 |
if (!skb) |
| 1132 |
goto out_sleep; |
| 1133 |
|
| 1134 |
ret = wl1251_cmd_template_set(wl, CMD_PS_POLL, |
| 1135 |
skb->data, |
| 1136 |
skb->len); |
| 1137 |
dev_kfree_skb(skb); |
| 1138 |
if (ret < 0) |
| 1139 |
goto out_sleep; |
| 1140 |
|
| 1141 |
ret = wl1251_acx_aid(wl, vif->cfg.aid); |
| 1142 |
if (ret < 0) |
| 1143 |
goto out_sleep; |
| 1144 |
} else { |
| 1145 |
/* use defaults when not associated */ |
| 1146 |
wl->beacon_int = WL1251_DEFAULT_BEACON_INT; |
| 1147 |
wl->dtim_period = WL1251_DEFAULT_DTIM_PERIOD; |
| 1148 |
} |
| 1149 |
} |
| 1150 |
if (changed & BSS_CHANGED_ERP_SLOT) { |
| 1151 |
if (bss_conf->use_short_slot) |
| 1152 |
ret = wl1251_acx_slot(wl, SLOT_TIME_SHORT); |
| 1153 |
else |
| 1154 |
ret = wl1251_acx_slot(wl, SLOT_TIME_LONG); |
| 1155 |
if (ret < 0) { |
| 1156 |
wl1251_warning("Set slot time failed %d", ret); |
| 1157 |
goto out_sleep; |
| 1158 |
} |
| 1159 |
} |
| 1160 |
|
| 1161 |
if (changed & BSS_CHANGED_ERP_PREAMBLE) { |
| 1162 |
if (bss_conf->use_short_preamble) |
| 1163 |
wl1251_acx_set_preamble(wl, ACX_PREAMBLE_SHORT); |
| 1164 |
else |
| 1165 |
wl1251_acx_set_preamble(wl, ACX_PREAMBLE_LONG); |
| 1166 |
} |
| 1167 |
|
| 1168 |
if (changed & BSS_CHANGED_ERP_CTS_PROT) { |
| 1169 |
if (bss_conf->use_cts_prot) |
| 1170 |
ret = wl1251_acx_cts_protect(wl, CTSPROTECT_ENABLE); |
| 1171 |
else |
| 1172 |
ret = wl1251_acx_cts_protect(wl, CTSPROTECT_DISABLE); |
| 1173 |
if (ret < 0) { |
| 1174 |
wl1251_warning("Set ctsprotect failed %d", ret); |
| 1175 |
goto out_sleep; |
| 1176 |
} |
| 1177 |
} |
| 1178 |
|
| 1179 |
if (changed & BSS_CHANGED_ARP_FILTER) { |
| 1180 |
__be32 addr = vif->cfg.arp_addr_list[0]; |
| 1181 |
WARN_ON(wl->bss_type != BSS_TYPE_STA_BSS); |
| 1182 |
|
| 1183 |
enable = vif->cfg.arp_addr_cnt == 1 && vif->cfg.assoc; |
| 1184 |
ret = wl1251_acx_arp_ip_filter(wl, enable, addr); |
| 1185 |
if (ret < 0) |
| 1186 |
goto out_sleep; |
| 1187 |
} |
| 1188 |
|
| 1189 |
if (changed & BSS_CHANGED_BEACON) { |
| 1190 |
beacon = ieee80211_beacon_get(hw, vif, 0); |
| 1191 |
if (!beacon) |
| 1192 |
goto out_sleep; |
| 1193 |
|
| 1194 |
ret = wl1251_cmd_template_set(wl, CMD_BEACON, beacon->data, |
| 1195 |
beacon->len); |
| 1196 |
|
| 1197 |
if (ret < 0) { |
| 1198 |
dev_kfree_skb(beacon); |
| 1199 |
goto out_sleep; |
| 1200 |
} |
| 1201 |
|
| 1202 |
ret = wl1251_cmd_template_set(wl, CMD_PROBE_RESP, beacon->data, |
| 1203 |
beacon->len); |
| 1204 |
|
| 1205 |
dev_kfree_skb(beacon); |
| 1206 |
|
| 1207 |
if (ret < 0) |
| 1208 |
goto out_sleep; |
| 1209 |
|
| 1210 |
ret = wl1251_join(wl, wl->bss_type, wl->channel, |
| 1211 |
wl->beacon_int, wl->dtim_period); |
| 1212 |
|
| 1213 |
if (ret < 0) |
| 1214 |
goto out_sleep; |
| 1215 |
} |
| 1216 |
|
| 1217 |
out_sleep: |
| 1218 |
wl1251_ps_elp_sleep(wl); |
| 1219 |
|
| 1220 |
out: |
| 1221 |
mutex_unlock(&wl->mutex); |
| 1222 |
} |
| 1223 |
|
| 1224 |
|
| 1225 |
/* can't be const, mac80211 writes to this */ |
| 1226 |
static struct ieee80211_rate wl1251_rates[] = { |
| 1227 |
{ .bitrate = 10, |
| 1228 |
.hw_value = 0x1, |
| 1229 |
.hw_value_short = 0x1, }, |
| 1230 |
{ .bitrate = 20, |
| 1231 |
.hw_value = 0x2, |
| 1232 |
.hw_value_short = 0x2, |
| 1233 |
.flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| 1234 |
{ .bitrate = 55, |
| 1235 |
.hw_value = 0x4, |
| 1236 |
.hw_value_short = 0x4, |
| 1237 |
.flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| 1238 |
{ .bitrate = 110, |
| 1239 |
.hw_value = 0x20, |
| 1240 |
.hw_value_short = 0x20, |
| 1241 |
.flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| 1242 |
{ .bitrate = 60, |
| 1243 |
.hw_value = 0x8, |
| 1244 |
.hw_value_short = 0x8, }, |
| 1245 |
{ .bitrate = 90, |
| 1246 |
.hw_value = 0x10, |
| 1247 |
.hw_value_short = 0x10, }, |
| 1248 |
{ .bitrate = 120, |
| 1249 |
.hw_value = 0x40, |
| 1250 |
.hw_value_short = 0x40, }, |
| 1251 |
{ .bitrate = 180, |
| 1252 |
.hw_value = 0x80, |
| 1253 |
.hw_value_short = 0x80, }, |
| 1254 |
{ .bitrate = 240, |
| 1255 |
.hw_value = 0x200, |
| 1256 |
.hw_value_short = 0x200, }, |
| 1257 |
{ .bitrate = 360, |
| 1258 |
.hw_value = 0x400, |
| 1259 |
.hw_value_short = 0x400, }, |
| 1260 |
{ .bitrate = 480, |
| 1261 |
.hw_value = 0x800, |
| 1262 |
.hw_value_short = 0x800, }, |
| 1263 |
{ .bitrate = 540, |
| 1264 |
.hw_value = 0x1000, |
| 1265 |
.hw_value_short = 0x1000, }, |
| 1266 |
}; |
| 1267 |
|
| 1268 |
/* can't be const, mac80211 writes to this */ |
| 1269 |
static struct ieee80211_channel wl1251_channels[] = { |
| 1270 |
{ .hw_value = 1, .center_freq = 2412}, |
| 1271 |
{ .hw_value = 2, .center_freq = 2417}, |
| 1272 |
{ .hw_value = 3, .center_freq = 2422}, |
| 1273 |
{ .hw_value = 4, .center_freq = 2427}, |
| 1274 |
{ .hw_value = 5, .center_freq = 2432}, |
| 1275 |
{ .hw_value = 6, .center_freq = 2437}, |
| 1276 |
{ .hw_value = 7, .center_freq = 2442}, |
| 1277 |
{ .hw_value = 8, .center_freq = 2447}, |
| 1278 |
{ .hw_value = 9, .center_freq = 2452}, |
| 1279 |
{ .hw_value = 10, .center_freq = 2457}, |
| 1280 |
{ .hw_value = 11, .center_freq = 2462}, |
| 1281 |
{ .hw_value = 12, .center_freq = 2467}, |
| 1282 |
{ .hw_value = 13, .center_freq = 2472}, |
| 1283 |
}; |
| 1284 |
|
| 1285 |
static int wl1251_op_conf_tx(struct ieee80211_hw *hw, |
| 1286 |
struct ieee80211_vif *vif, |
| 1287 |
unsigned int link_id, u16 queue, |
| 1288 |
const struct ieee80211_tx_queue_params *params) |
| 1289 |
{ |
| 1290 |
enum wl1251_acx_ps_scheme ps_scheme; |
| 1291 |
struct wl1251 *wl = hw->priv; |
| 1292 |
int ret; |
| 1293 |
|
| 1294 |
mutex_lock(&wl->mutex); |
| 1295 |
|
| 1296 |
wl1251_debug(DEBUG_MAC80211, "mac80211 conf tx %d", queue); |
| 1297 |
|
| 1298 |
ret = wl1251_ps_elp_wakeup(wl); |
| 1299 |
if (ret < 0) |
| 1300 |
goto out; |
| 1301 |
|
| 1302 |
/* mac80211 uses units of 32 usec */ |
| 1303 |
ret = wl1251_acx_ac_cfg(wl, wl1251_tx_get_queue(queue), |
| 1304 |
params->cw_min, params->cw_max, |
| 1305 |
params->aifs, params->txop * 32); |
| 1306 |
if (ret < 0) |
| 1307 |
goto out_sleep; |
| 1308 |
|
| 1309 |
if (params->uapsd) |
| 1310 |
ps_scheme = WL1251_ACX_PS_SCHEME_UPSD_TRIGGER; |
| 1311 |
else |
| 1312 |
ps_scheme = WL1251_ACX_PS_SCHEME_LEGACY; |
| 1313 |
|
| 1314 |
ret = wl1251_acx_tid_cfg(wl, wl1251_tx_get_queue(queue), |
| 1315 |
CHANNEL_TYPE_EDCF, |
| 1316 |
wl1251_tx_get_queue(queue), ps_scheme, |
| 1317 |
WL1251_ACX_ACK_POLICY_LEGACY); |
| 1318 |
if (ret < 0) |
| 1319 |
goto out_sleep; |
| 1320 |
|
| 1321 |
out_sleep: |
| 1322 |
wl1251_ps_elp_sleep(wl); |
| 1323 |
|
| 1324 |
out: |
| 1325 |
mutex_unlock(&wl->mutex); |
| 1326 |
|
| 1327 |
return ret; |
| 1328 |
} |
| 1329 |
|
| 1330 |
static int wl1251_op_get_survey(struct ieee80211_hw *hw, int idx, |
| 1331 |
struct survey_info *survey) |
| 1332 |
{ |
| 1333 |
struct wl1251 *wl = hw->priv; |
| 1334 |
struct ieee80211_conf *conf = &hw->conf; |
| 1335 |
|
| 1336 |
if (idx != 0) |
| 1337 |
return -ENOENT; |
| 1338 |
|
| 1339 |
survey->channel = conf->chandef.chan; |
| 1340 |
survey->filled = SURVEY_INFO_NOISE_DBM; |
| 1341 |
survey->noise = wl->noise; |
| 1342 |
|
| 1343 |
return 0; |
| 1344 |
} |
| 1345 |
|
| 1346 |
/* can't be const, mac80211 writes to this */ |
| 1347 |
static struct ieee80211_supported_band wl1251_band_2ghz = { |
| 1348 |
.channels = wl1251_channels, |
| 1349 |
.n_channels = ARRAY_SIZE(wl1251_channels), |
| 1350 |
.bitrates = wl1251_rates, |
| 1351 |
.n_bitrates = ARRAY_SIZE(wl1251_rates), |
| 1352 |
}; |
| 1353 |
|
| 1354 |
static const struct ieee80211_ops wl1251_ops = { |
| 1355 |
.add_chanctx = ieee80211_emulate_add_chanctx, |
| 1356 |
.remove_chanctx = ieee80211_emulate_remove_chanctx, |
| 1357 |
.change_chanctx = ieee80211_emulate_change_chanctx, |
| 1358 |
.switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx, |
| 1359 |
.start = wl1251_op_start, |
| 1360 |
.stop = wl1251_op_stop, |
| 1361 |
.add_interface = wl1251_op_add_interface, |
| 1362 |
.remove_interface = wl1251_op_remove_interface, |
| 1363 |
.config = wl1251_op_config, |
| 1364 |
.prepare_multicast = wl1251_op_prepare_multicast, |
| 1365 |
.configure_filter = wl1251_op_configure_filter, |
| 1366 |
.tx = wl1251_op_tx, |
| 1367 |
.wake_tx_queue = ieee80211_handle_wake_tx_queue, |
| 1368 |
.set_key = wl1251_op_set_key, |
| 1369 |
.hw_scan = wl1251_op_hw_scan, |
| 1370 |
.bss_info_changed = wl1251_op_bss_info_changed, |
| 1371 |
.set_rts_threshold = wl1251_op_set_rts_threshold, |
| 1372 |
.conf_tx = wl1251_op_conf_tx, |
| 1373 |
.get_survey = wl1251_op_get_survey, |
| 1374 |
}; |
| 1375 |
|
| 1376 |
static int wl1251_read_eeprom_byte(struct wl1251 *wl, off_t offset, u8 *data) |
| 1377 |
{ |
| 1378 |
unsigned long timeout; |
| 1379 |
|
| 1380 |
wl1251_reg_write32(wl, EE_ADDR, offset); |
| 1381 |
wl1251_reg_write32(wl, EE_CTL, EE_CTL_READ); |
| 1382 |
|
| 1383 |
/* EE_CTL_READ clears when data is ready */ |
| 1384 |
timeout = jiffies + msecs_to_jiffies(100); |
| 1385 |
while (1) { |
| 1386 |
if (!(wl1251_reg_read32(wl, EE_CTL) & EE_CTL_READ)) |
| 1387 |
break; |
| 1388 |
|
| 1389 |
if (time_after(jiffies, timeout)) |
| 1390 |
return -ETIMEDOUT; |
| 1391 |
|
| 1392 |
msleep(1); |
| 1393 |
} |
| 1394 |
|
| 1395 |
*data = wl1251_reg_read32(wl, EE_DATA); |
| 1396 |
return 0; |
| 1397 |
} |
| 1398 |
|
| 1399 |
static int wl1251_read_eeprom(struct wl1251 *wl, off_t offset, |
| 1400 |
u8 *data, size_t len) |
| 1401 |
{ |
| 1402 |
size_t i; |
| 1403 |
int ret; |
| 1404 |
|
| 1405 |
wl1251_reg_write32(wl, EE_START, 0); |
| 1406 |
|
| 1407 |
for (i = 0; i < len; i++) { |
| 1408 |
ret = wl1251_read_eeprom_byte(wl, offset + i, &data[i]); |
| 1409 |
if (ret < 0) |
| 1410 |
return ret; |
| 1411 |
} |
| 1412 |
|
| 1413 |
return 0; |
| 1414 |
} |
| 1415 |
|
| 1416 |
static int wl1251_read_eeprom_mac(struct wl1251 *wl) |
| 1417 |
{ |
| 1418 |
u8 mac[ETH_ALEN]; |
| 1419 |
int i, ret; |
| 1420 |
|
| 1421 |
wl1251_set_partition(wl, 0, 0, REGISTERS_BASE, REGISTERS_DOWN_SIZE); |
| 1422 |
|
| 1423 |
ret = wl1251_read_eeprom(wl, 0x1c, mac, sizeof(mac)); |
| 1424 |
if (ret < 0) { |
| 1425 |
wl1251_warning("failed to read MAC address from EEPROM"); |
| 1426 |
return ret; |
| 1427 |
} |
| 1428 |
|
| 1429 |
/* MAC is stored in reverse order */ |
| 1430 |
for (i = 0; i < ETH_ALEN; i++) |
| 1431 |
wl->mac_addr[i] = mac[ETH_ALEN - i - 1]; |
| 1432 |
|
| 1433 |
return 0; |
| 1434 |
} |
| 1435 |
|
| 1436 |
#define NVS_OFF_MAC_LEN 0x19 |
| 1437 |
#define NVS_OFF_MAC_ADDR_LO 0x1a |
| 1438 |
#define NVS_OFF_MAC_ADDR_HI 0x1b |
| 1439 |
#define NVS_OFF_MAC_DATA 0x1c |
| 1440 |
|
| 1441 |
static int wl1251_check_nvs_mac(struct wl1251 *wl) |
| 1442 |
{ |
| 1443 |
if (wl->nvs_len < 0x24) |
| 1444 |
return -ENODATA; |
| 1445 |
|
| 1446 |
/* length is 2 and data address is 0x546c (ANDed with 0xfffe) */ |
| 1447 |
if (wl->nvs[NVS_OFF_MAC_LEN] != 2 || |
| 1448 |
wl->nvs[NVS_OFF_MAC_ADDR_LO] != 0x6d || |
| 1449 |
wl->nvs[NVS_OFF_MAC_ADDR_HI] != 0x54) |
| 1450 |
return -EINVAL; |
| 1451 |
|
| 1452 |
return 0; |
| 1453 |
} |
| 1454 |
|
| 1455 |
static int wl1251_read_nvs_mac(struct wl1251 *wl) |
| 1456 |
{ |
| 1457 |
u8 mac[ETH_ALEN]; |
| 1458 |
int i, ret; |
| 1459 |
|
| 1460 |
ret = wl1251_check_nvs_mac(wl); |
| 1461 |
if (ret) |
| 1462 |
return ret; |
| 1463 |
|
| 1464 |
/* MAC is stored in reverse order */ |
| 1465 |
for (i = 0; i < ETH_ALEN; i++) |
| 1466 |
mac[i] = wl->nvs[NVS_OFF_MAC_DATA + ETH_ALEN - i - 1]; |
| 1467 |
|
| 1468 |
/* 00:00:20:07:03:09 is in example file wl1251-nvs.bin, so invalid */ |
| 1469 |
if (ether_addr_equal_unaligned(mac, "\x00\x00\x20\x07\x03\x09")) |
| 1470 |
return -EINVAL; |
| 1471 |
|
| 1472 |
memcpy(wl->mac_addr, mac, ETH_ALEN); |
| 1473 |
return 0; |
| 1474 |
} |
| 1475 |
|
| 1476 |
static int wl1251_write_nvs_mac(struct wl1251 *wl) |
| 1477 |
{ |
| 1478 |
int i, ret; |
| 1479 |
|
| 1480 |
ret = wl1251_check_nvs_mac(wl); |
| 1481 |
if (ret) |
| 1482 |
return ret; |
| 1483 |
|
| 1484 |
/* MAC is stored in reverse order */ |
| 1485 |
for (i = 0; i < ETH_ALEN; i++) |
| 1486 |
wl->nvs[NVS_OFF_MAC_DATA + i] = wl->mac_addr[ETH_ALEN - i - 1]; |
| 1487 |
|
| 1488 |
return 0; |
| 1489 |
} |
| 1490 |
|
| 1491 |
static int wl1251_register_hw(struct wl1251 *wl) |
| 1492 |
{ |
| 1493 |
int ret; |
| 1494 |
|
| 1495 |
if (wl->mac80211_registered) |
| 1496 |
return 0; |
| 1497 |
|
| 1498 |
SET_IEEE80211_PERM_ADDR(wl->hw, wl->mac_addr); |
| 1499 |
|
| 1500 |
ret = ieee80211_register_hw(wl->hw); |
| 1501 |
if (ret < 0) { |
| 1502 |
wl1251_error("unable to register mac80211 hw: %d", ret); |
| 1503 |
return ret; |
| 1504 |
} |
| 1505 |
|
| 1506 |
wl->mac80211_registered = true; |
| 1507 |
|
| 1508 |
wl1251_notice("loaded"); |
| 1509 |
|
| 1510 |
return 0; |
| 1511 |
} |
| 1512 |
|
| 1513 |
int wl1251_init_ieee80211(struct wl1251 *wl) |
| 1514 |
{ |
| 1515 |
int ret; |
| 1516 |
|
| 1517 |
/* The tx descriptor buffer and the TKIP space */ |
| 1518 |
wl->hw->extra_tx_headroom = sizeof(struct tx_double_buffer_desc) |
| 1519 |
+ WL1251_TKIP_IV_SPACE; |
| 1520 |
|
| 1521 |
/* unit us */ |
| 1522 |
/* FIXME: find a proper value */ |
| 1523 |
|
| 1524 |
ieee80211_hw_set(wl->hw, SIGNAL_DBM); |
| 1525 |
ieee80211_hw_set(wl->hw, SUPPORTS_PS); |
| 1526 |
|
| 1527 |
wl->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) | |
| 1528 |
BIT(NL80211_IFTYPE_ADHOC); |
| 1529 |
wl->hw->wiphy->max_scan_ssids = 1; |
| 1530 |
|
| 1531 |
/* We set max_scan_ie_len to a random value to make wpa_supplicant scans not |
| 1532 |
* fail, as the driver will the ignore the extra passed IEs anyway |
| 1533 |
*/ |
| 1534 |
wl->hw->wiphy->max_scan_ie_len = 512; |
| 1535 |
|
| 1536 |
wl->hw->wiphy->bands[NL80211_BAND_2GHZ] = &wl1251_band_2ghz; |
| 1537 |
|
| 1538 |
wl->hw->queues = 4; |
| 1539 |
|
| 1540 |
if (wl->nvs == NULL && !wl->use_eeprom) { |
| 1541 |
ret = wl1251_fetch_nvs(wl); |
| 1542 |
if (ret < 0) |
| 1543 |
goto out; |
| 1544 |
} |
| 1545 |
|
| 1546 |
if (wl->use_eeprom) |
| 1547 |
ret = wl1251_read_eeprom_mac(wl); |
| 1548 |
else |
| 1549 |
ret = wl1251_read_nvs_mac(wl); |
| 1550 |
|
| 1551 |
if (ret == 0 && !is_valid_ether_addr(wl->mac_addr)) |
| 1552 |
ret = -EINVAL; |
| 1553 |
|
| 1554 |
if (ret < 0) { |
| 1555 |
/* |
| 1556 |
* In case our MAC address is not correctly set, |
| 1557 |
* we use a random but Nokia MAC. |
| 1558 |
*/ |
| 1559 |
static const u8 nokia_oui[3] = {0x00, 0x1f, 0xdf}; |
| 1560 |
memcpy(wl->mac_addr, nokia_oui, 3); |
| 1561 |
get_random_bytes(wl->mac_addr + 3, 3); |
| 1562 |
if (!wl->use_eeprom) |
| 1563 |
wl1251_write_nvs_mac(wl); |
| 1564 |
wl1251_warning("MAC address in eeprom or nvs data is not valid"); |
| 1565 |
wl1251_warning("Setting random MAC address: %pM", wl->mac_addr); |
| 1566 |
} |
| 1567 |
|
| 1568 |
ret = wl1251_register_hw(wl); |
| 1569 |
if (ret) |
| 1570 |
goto out; |
| 1571 |
|
| 1572 |
wl1251_debugfs_init(wl); |
| 1573 |
wl1251_notice("initialized"); |
| 1574 |
|
| 1575 |
ret = 0; |
| 1576 |
|
| 1577 |
out: |
| 1578 |
return ret; |
| 1579 |
} |
| 1580 |
EXPORT_SYMBOL_GPL(wl1251_init_ieee80211); |
| 1581 |
|
| 1582 |
struct ieee80211_hw *wl1251_alloc_hw(void) |
| 1583 |
{ |
| 1584 |
struct ieee80211_hw *hw; |
| 1585 |
struct wl1251 *wl; |
| 1586 |
int i; |
| 1587 |
|
| 1588 |
hw = ieee80211_alloc_hw(sizeof(*wl), &wl1251_ops); |
| 1589 |
if (!hw) { |
| 1590 |
wl1251_error("could not alloc ieee80211_hw"); |
| 1591 |
return ERR_PTR(-ENOMEM); |
| 1592 |
} |
| 1593 |
|
| 1594 |
wl = hw->priv; |
| 1595 |
memset(wl, 0, sizeof(*wl)); |
| 1596 |
|
| 1597 |
wl->hw = hw; |
| 1598 |
|
| 1599 |
wl->data_in_count = 0; |
| 1600 |
|
| 1601 |
skb_queue_head_init(&wl->tx_queue); |
| 1602 |
|
| 1603 |
INIT_DELAYED_WORK(&wl->elp_work, wl1251_elp_work); |
| 1604 |
wl->channel = WL1251_DEFAULT_CHANNEL; |
| 1605 |
wl->monitor_present = false; |
| 1606 |
wl->joined = false; |
| 1607 |
wl->scanning = false; |
| 1608 |
wl->bss_type = MAX_BSS_TYPE; |
| 1609 |
wl->default_key = 0; |
| 1610 |
wl->listen_int = 1; |
| 1611 |
wl->rx_counter = 0; |
| 1612 |
wl->rx_handled = 0; |
| 1613 |
wl->rx_current_buffer = 0; |
| 1614 |
wl->rx_last_id = 0; |
| 1615 |
wl->rx_config = WL1251_DEFAULT_RX_CONFIG; |
| 1616 |
wl->rx_filter = WL1251_DEFAULT_RX_FILTER; |
| 1617 |
wl->elp = false; |
| 1618 |
wl->station_mode = STATION_ACTIVE_MODE; |
| 1619 |
wl->psm_requested = false; |
| 1620 |
wl->psm_entry_retry = 0; |
| 1621 |
wl->tx_queue_stopped = false; |
| 1622 |
wl->power_level = WL1251_DEFAULT_POWER_LEVEL; |
| 1623 |
wl->rssi_thold = 0; |
| 1624 |
wl->beacon_int = WL1251_DEFAULT_BEACON_INT; |
| 1625 |
wl->dtim_period = WL1251_DEFAULT_DTIM_PERIOD; |
| 1626 |
wl->vif = NULL; |
| 1627 |
|
| 1628 |
for (i = 0; i < FW_TX_CMPLT_BLOCK_SIZE; i++) |
| 1629 |
wl->tx_frames[i] = NULL; |
| 1630 |
|
| 1631 |
wl->next_tx_complete = 0; |
| 1632 |
|
| 1633 |
INIT_WORK(&wl->irq_work, wl1251_irq_work); |
| 1634 |
INIT_WORK(&wl->tx_work, wl1251_tx_work); |
| 1635 |
|
| 1636 |
wl->state = WL1251_STATE_OFF; |
| 1637 |
mutex_init(&wl->mutex); |
| 1638 |
spin_lock_init(&wl->wl_lock); |
| 1639 |
|
| 1640 |
wl->tx_mgmt_frm_rate = DEFAULT_HW_GEN_TX_RATE; |
| 1641 |
wl->tx_mgmt_frm_mod = DEFAULT_HW_GEN_MODULATION_TYPE; |
| 1642 |
|
| 1643 |
wl->rx_descriptor = kmalloc_obj(*wl->rx_descriptor); |
| 1644 |
if (!wl->rx_descriptor) { |
| 1645 |
wl1251_error("could not allocate memory for rx descriptor"); |
| 1646 |
ieee80211_free_hw(hw); |
| 1647 |
return ERR_PTR(-ENOMEM); |
| 1648 |
} |
| 1649 |
|
| 1650 |
return hw; |
| 1651 |
} |
| 1652 |
EXPORT_SYMBOL_GPL(wl1251_alloc_hw); |
| 1653 |
|
| 1654 |
int wl1251_free_hw(struct wl1251 *wl) |
| 1655 |
{ |
| 1656 |
ieee80211_unregister_hw(wl->hw); |
| 1657 |
|
| 1658 |
wl1251_debugfs_exit(wl); |
| 1659 |
|
| 1660 |
kfree(wl->target_mem_map); |
| 1661 |
kfree(wl->data_path); |
| 1662 |
vfree(wl->fw); |
| 1663 |
wl->fw = NULL; |
| 1664 |
kfree(wl->nvs); |
| 1665 |
wl->nvs = NULL; |
| 1666 |
|
| 1667 |
kfree(wl->rx_descriptor); |
| 1668 |
wl->rx_descriptor = NULL; |
| 1669 |
|
| 1670 |
ieee80211_free_hw(wl->hw); |
| 1671 |
|
| 1672 |
return 0; |
| 1673 |
} |
| 1674 |
EXPORT_SYMBOL_GPL(wl1251_free_hw); |
| 1675 |
|
| 1676 |
MODULE_DESCRIPTION("TI wl1251 Wireless LAN Driver Core"); |
| 1677 |
MODULE_LICENSE("GPL"); |
| 1678 |
MODULE_AUTHOR("Kalle Valo <[email protected]>"); |
| 1679 |
MODULE_FIRMWARE(WL1251_FW_NAME); |
| 1680 |
MODULE_FIRMWARE(WL1251_NVS_NAME); |