| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/****************************************************************************** |
| 3 |
* |
| 4 |
* Copyright(c) 2003 - 2011 Intel Corporation. All rights reserved. |
| 5 |
* |
| 6 |
* Portions of this file are derived from the ipw3945 project, as well |
| 7 |
* as portions of the ieee80211 subsystem header files. |
| 8 |
* |
| 9 |
* Contact Information: |
| 10 |
* Intel Linux Wireless <[email protected]> |
| 11 |
* Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 |
| 12 |
* |
| 13 |
*****************************************************************************/ |
| 14 |
|
| 15 |
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| 16 |
|
| 17 |
#include <linux/kernel.h> |
| 18 |
#include <linux/module.h> |
| 19 |
#include <linux/init.h> |
| 20 |
#include <linux/pci.h> |
| 21 |
#include <linux/slab.h> |
| 22 |
#include <linux/dma-mapping.h> |
| 23 |
#include <linux/delay.h> |
| 24 |
#include <linux/sched.h> |
| 25 |
#include <linux/skbuff.h> |
| 26 |
#include <linux/netdevice.h> |
| 27 |
#include <linux/firmware.h> |
| 28 |
#include <linux/etherdevice.h> |
| 29 |
#include <linux/if_arp.h> |
| 30 |
#include <linux/units.h> |
| 31 |
|
| 32 |
#include <net/mac80211.h> |
| 33 |
|
| 34 |
#include <asm/div64.h> |
| 35 |
|
| 36 |
#define DRV_NAME "iwl4965" |
| 37 |
|
| 38 |
#include "common.h" |
| 39 |
#include "4965.h" |
| 40 |
|
| 41 |
/****************************************************************************** |
| 42 |
* |
| 43 |
* module boiler plate |
| 44 |
* |
| 45 |
******************************************************************************/ |
| 46 |
|
| 47 |
/* |
| 48 |
* module name, copyright, version, etc. |
| 49 |
*/ |
| 50 |
#define DRV_DESCRIPTION "Intel(R) Wireless WiFi 4965 driver for Linux" |
| 51 |
|
| 52 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 53 |
#define VD "d" |
| 54 |
#else |
| 55 |
#define VD |
| 56 |
#endif |
| 57 |
|
| 58 |
#define DRV_VERSION IWLWIFI_VERSION VD |
| 59 |
|
| 60 |
MODULE_DESCRIPTION(DRV_DESCRIPTION); |
| 61 |
MODULE_VERSION(DRV_VERSION); |
| 62 |
MODULE_AUTHOR(DRV_COPYRIGHT " " DRV_AUTHOR); |
| 63 |
MODULE_LICENSE("GPL"); |
| 64 |
MODULE_ALIAS("iwl4965"); |
| 65 |
|
| 66 |
void |
| 67 |
il4965_check_abort_status(struct il_priv *il, u8 frame_count, u32 status) |
| 68 |
{ |
| 69 |
if (frame_count == 1 && status == TX_STATUS_FAIL_RFKILL_FLUSH) { |
| 70 |
IL_ERR("Tx flush command to flush out all frames\n"); |
| 71 |
if (!test_bit(S_EXIT_PENDING, &il->status)) |
| 72 |
queue_work(il->workqueue, &il->tx_flush); |
| 73 |
} |
| 74 |
} |
| 75 |
|
| 76 |
/* |
| 77 |
* EEPROM |
| 78 |
*/ |
| 79 |
struct il_mod_params il4965_mod_params = { |
| 80 |
.restart_fw = 1, |
| 81 |
/* the rest are 0 by default */ |
| 82 |
}; |
| 83 |
|
| 84 |
void |
| 85 |
il4965_rx_queue_reset(struct il_priv *il, struct il_rx_queue *rxq) |
| 86 |
{ |
| 87 |
unsigned long flags; |
| 88 |
int i; |
| 89 |
spin_lock_irqsave(&rxq->lock, flags); |
| 90 |
INIT_LIST_HEAD(&rxq->rx_free); |
| 91 |
INIT_LIST_HEAD(&rxq->rx_used); |
| 92 |
/* Fill the rx_used queue with _all_ of the Rx buffers */ |
| 93 |
for (i = 0; i < RX_FREE_BUFFERS + RX_QUEUE_SIZE; i++) { |
| 94 |
/* In the reset function, these buffers may have been allocated |
| 95 |
* to an SKB, so we need to unmap and free potential storage */ |
| 96 |
if (rxq->pool[i].page != NULL) { |
| 97 |
dma_unmap_page(&il->pci_dev->dev, |
| 98 |
rxq->pool[i].page_dma, |
| 99 |
PAGE_SIZE << il->hw_params.rx_page_order, |
| 100 |
DMA_FROM_DEVICE); |
| 101 |
__il_free_pages(il, rxq->pool[i].page); |
| 102 |
rxq->pool[i].page = NULL; |
| 103 |
} |
| 104 |
list_add_tail(&rxq->pool[i].list, &rxq->rx_used); |
| 105 |
} |
| 106 |
|
| 107 |
for (i = 0; i < RX_QUEUE_SIZE; i++) |
| 108 |
rxq->queue[i] = NULL; |
| 109 |
|
| 110 |
/* Set us so that we have processed and used all buffers, but have |
| 111 |
* not restocked the Rx queue with fresh buffers */ |
| 112 |
rxq->read = rxq->write = 0; |
| 113 |
rxq->write_actual = 0; |
| 114 |
rxq->free_count = 0; |
| 115 |
spin_unlock_irqrestore(&rxq->lock, flags); |
| 116 |
} |
| 117 |
|
| 118 |
int |
| 119 |
il4965_rx_init(struct il_priv *il, struct il_rx_queue *rxq) |
| 120 |
{ |
| 121 |
u32 rb_size; |
| 122 |
const u32 rfdnlog = RX_QUEUE_SIZE_LOG; /* 256 RBDs */ |
| 123 |
u32 rb_timeout = 0; |
| 124 |
|
| 125 |
if (il->cfg->mod_params->amsdu_size_8K) |
| 126 |
rb_size = FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K; |
| 127 |
else |
| 128 |
rb_size = FH49_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K; |
| 129 |
|
| 130 |
/* Stop Rx DMA */ |
| 131 |
il_wr(il, FH49_MEM_RCSR_CHNL0_CONFIG_REG, 0); |
| 132 |
|
| 133 |
/* Reset driver's Rx queue write idx */ |
| 134 |
il_wr(il, FH49_RSCSR_CHNL0_RBDCB_WPTR_REG, 0); |
| 135 |
|
| 136 |
/* Tell device where to find RBD circular buffer in DRAM */ |
| 137 |
il_wr(il, FH49_RSCSR_CHNL0_RBDCB_BASE_REG, (u32) (rxq->bd_dma >> 8)); |
| 138 |
|
| 139 |
/* Tell device where in DRAM to update its Rx status */ |
| 140 |
il_wr(il, FH49_RSCSR_CHNL0_STTS_WPTR_REG, rxq->rb_stts_dma >> 4); |
| 141 |
|
| 142 |
/* Enable Rx DMA |
| 143 |
* Direct rx interrupts to hosts |
| 144 |
* Rx buffer size 4 or 8k |
| 145 |
* RB timeout 0x10 |
| 146 |
* 256 RBDs |
| 147 |
*/ |
| 148 |
il_wr(il, FH49_MEM_RCSR_CHNL0_CONFIG_REG, |
| 149 |
FH49_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL | |
| 150 |
FH49_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL | |
| 151 |
FH49_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MSK | |
| 152 |
rb_size | |
| 153 |
(rb_timeout << FH49_RCSR_RX_CONFIG_REG_IRQ_RBTH_POS) | |
| 154 |
(rfdnlog << FH49_RCSR_RX_CONFIG_RBDCB_SIZE_POS)); |
| 155 |
|
| 156 |
/* Set interrupt coalescing timer to default (2048 usecs) */ |
| 157 |
il_write8(il, CSR_INT_COALESCING, IL_HOST_INT_TIMEOUT_DEF); |
| 158 |
|
| 159 |
return 0; |
| 160 |
} |
| 161 |
|
| 162 |
static void |
| 163 |
il4965_set_pwr_vmain(struct il_priv *il) |
| 164 |
{ |
| 165 |
/* |
| 166 |
* (for documentation purposes) |
| 167 |
* to set power to V_AUX, do: |
| 168 |
|
| 169 |
if (pci_pme_capable(il->pci_dev, PCI_D3cold)) |
| 170 |
il_set_bits_mask_prph(il, APMG_PS_CTRL_REG, |
| 171 |
APMG_PS_CTRL_VAL_PWR_SRC_VAUX, |
| 172 |
~APMG_PS_CTRL_MSK_PWR_SRC); |
| 173 |
*/ |
| 174 |
|
| 175 |
il_set_bits_mask_prph(il, APMG_PS_CTRL_REG, |
| 176 |
APMG_PS_CTRL_VAL_PWR_SRC_VMAIN, |
| 177 |
~APMG_PS_CTRL_MSK_PWR_SRC); |
| 178 |
} |
| 179 |
|
| 180 |
int |
| 181 |
il4965_hw_nic_init(struct il_priv *il) |
| 182 |
{ |
| 183 |
unsigned long flags; |
| 184 |
struct il_rx_queue *rxq = &il->rxq; |
| 185 |
int ret; |
| 186 |
|
| 187 |
spin_lock_irqsave(&il->lock, flags); |
| 188 |
il_apm_init(il); |
| 189 |
/* Set interrupt coalescing calibration timer to default (512 usecs) */ |
| 190 |
il_write8(il, CSR_INT_COALESCING, IL_HOST_INT_CALIB_TIMEOUT_DEF); |
| 191 |
spin_unlock_irqrestore(&il->lock, flags); |
| 192 |
|
| 193 |
il4965_set_pwr_vmain(il); |
| 194 |
il4965_nic_config(il); |
| 195 |
|
| 196 |
/* Allocate the RX queue, or reset if it is already allocated */ |
| 197 |
if (!rxq->bd) { |
| 198 |
ret = il_rx_queue_alloc(il); |
| 199 |
if (ret) { |
| 200 |
IL_ERR("Unable to initialize Rx queue\n"); |
| 201 |
return -ENOMEM; |
| 202 |
} |
| 203 |
} else |
| 204 |
il4965_rx_queue_reset(il, rxq); |
| 205 |
|
| 206 |
il4965_rx_replenish(il); |
| 207 |
|
| 208 |
il4965_rx_init(il, rxq); |
| 209 |
|
| 210 |
spin_lock_irqsave(&il->lock, flags); |
| 211 |
|
| 212 |
rxq->need_update = 1; |
| 213 |
il_rx_queue_update_write_ptr(il, rxq); |
| 214 |
|
| 215 |
spin_unlock_irqrestore(&il->lock, flags); |
| 216 |
|
| 217 |
/* Allocate or reset and init all Tx and Command queues */ |
| 218 |
if (!il->txq) { |
| 219 |
ret = il4965_txq_ctx_alloc(il); |
| 220 |
if (ret) |
| 221 |
return ret; |
| 222 |
} else |
| 223 |
il4965_txq_ctx_reset(il); |
| 224 |
|
| 225 |
set_bit(S_INIT, &il->status); |
| 226 |
|
| 227 |
return 0; |
| 228 |
} |
| 229 |
|
| 230 |
/* |
| 231 |
* il4965_dma_addr2rbd_ptr - convert a DMA address to a uCode read buffer ptr |
| 232 |
*/ |
| 233 |
static inline __le32 |
| 234 |
il4965_dma_addr2rbd_ptr(struct il_priv *il, dma_addr_t dma_addr) |
| 235 |
{ |
| 236 |
return cpu_to_le32((u32) (dma_addr >> 8)); |
| 237 |
} |
| 238 |
|
| 239 |
/* |
| 240 |
* il4965_rx_queue_restock - refill RX queue from pre-allocated pool |
| 241 |
* |
| 242 |
* If there are slots in the RX queue that need to be restocked, |
| 243 |
* and we have free pre-allocated buffers, fill the ranks as much |
| 244 |
* as we can, pulling from rx_free. |
| 245 |
* |
| 246 |
* This moves the 'write' idx forward to catch up with 'processed', and |
| 247 |
* also updates the memory address in the firmware to reference the new |
| 248 |
* target buffer. |
| 249 |
*/ |
| 250 |
void |
| 251 |
il4965_rx_queue_restock(struct il_priv *il) |
| 252 |
{ |
| 253 |
struct il_rx_queue *rxq = &il->rxq; |
| 254 |
struct list_head *element; |
| 255 |
struct il_rx_buf *rxb; |
| 256 |
unsigned long flags; |
| 257 |
|
| 258 |
spin_lock_irqsave(&rxq->lock, flags); |
| 259 |
while (il_rx_queue_space(rxq) > 0 && rxq->free_count) { |
| 260 |
/* The overwritten rxb must be a used one */ |
| 261 |
rxb = rxq->queue[rxq->write]; |
| 262 |
BUG_ON(rxb && rxb->page); |
| 263 |
|
| 264 |
/* Get next free Rx buffer, remove from free list */ |
| 265 |
element = rxq->rx_free.next; |
| 266 |
rxb = list_entry(element, struct il_rx_buf, list); |
| 267 |
list_del(element); |
| 268 |
|
| 269 |
/* Point to Rx buffer via next RBD in circular buffer */ |
| 270 |
rxq->bd[rxq->write] = |
| 271 |
il4965_dma_addr2rbd_ptr(il, rxb->page_dma); |
| 272 |
rxq->queue[rxq->write] = rxb; |
| 273 |
rxq->write = (rxq->write + 1) & RX_QUEUE_MASK; |
| 274 |
rxq->free_count--; |
| 275 |
} |
| 276 |
spin_unlock_irqrestore(&rxq->lock, flags); |
| 277 |
/* If the pre-allocated buffer pool is dropping low, schedule to |
| 278 |
* refill it */ |
| 279 |
if (rxq->free_count <= RX_LOW_WATERMARK) |
| 280 |
queue_work(il->workqueue, &il->rx_replenish); |
| 281 |
|
| 282 |
/* If we've added more space for the firmware to place data, tell it. |
| 283 |
* Increment device's write pointer in multiples of 8. */ |
| 284 |
if (rxq->write_actual != (rxq->write & ~0x7)) { |
| 285 |
spin_lock_irqsave(&rxq->lock, flags); |
| 286 |
rxq->need_update = 1; |
| 287 |
spin_unlock_irqrestore(&rxq->lock, flags); |
| 288 |
il_rx_queue_update_write_ptr(il, rxq); |
| 289 |
} |
| 290 |
} |
| 291 |
|
| 292 |
/* |
| 293 |
* il4965_rx_replenish - Move all used packet from rx_used to rx_free |
| 294 |
* |
| 295 |
* When moving to rx_free an SKB is allocated for the slot. |
| 296 |
* |
| 297 |
* Also restock the Rx queue via il_rx_queue_restock. |
| 298 |
* This is called as a scheduled work item (except for during initialization) |
| 299 |
*/ |
| 300 |
static void |
| 301 |
il4965_rx_allocate(struct il_priv *il, gfp_t priority) |
| 302 |
{ |
| 303 |
struct il_rx_queue *rxq = &il->rxq; |
| 304 |
struct list_head *element; |
| 305 |
struct il_rx_buf *rxb; |
| 306 |
struct page *page; |
| 307 |
dma_addr_t page_dma; |
| 308 |
unsigned long flags; |
| 309 |
gfp_t gfp_mask = priority; |
| 310 |
|
| 311 |
while (1) { |
| 312 |
spin_lock_irqsave(&rxq->lock, flags); |
| 313 |
if (list_empty(&rxq->rx_used)) { |
| 314 |
spin_unlock_irqrestore(&rxq->lock, flags); |
| 315 |
return; |
| 316 |
} |
| 317 |
spin_unlock_irqrestore(&rxq->lock, flags); |
| 318 |
|
| 319 |
if (rxq->free_count > RX_LOW_WATERMARK) |
| 320 |
gfp_mask |= __GFP_NOWARN; |
| 321 |
|
| 322 |
if (il->hw_params.rx_page_order > 0) |
| 323 |
gfp_mask |= __GFP_COMP; |
| 324 |
|
| 325 |
/* Alloc a new receive buffer */ |
| 326 |
page = alloc_pages(gfp_mask, il->hw_params.rx_page_order); |
| 327 |
if (!page) { |
| 328 |
if (net_ratelimit()) |
| 329 |
D_INFO("alloc_pages failed, " "order: %d\n", |
| 330 |
il->hw_params.rx_page_order); |
| 331 |
|
| 332 |
if (rxq->free_count <= RX_LOW_WATERMARK && |
| 333 |
net_ratelimit()) |
| 334 |
IL_ERR("Failed to alloc_pages with %s. " |
| 335 |
"Only %u free buffers remaining.\n", |
| 336 |
priority == |
| 337 |
GFP_ATOMIC ? "GFP_ATOMIC" : "GFP_KERNEL", |
| 338 |
rxq->free_count); |
| 339 |
/* We don't reschedule replenish work here -- we will |
| 340 |
* call the restock method and if it still needs |
| 341 |
* more buffers it will schedule replenish */ |
| 342 |
return; |
| 343 |
} |
| 344 |
|
| 345 |
/* Get physical address of the RB */ |
| 346 |
page_dma = dma_map_page(&il->pci_dev->dev, page, 0, |
| 347 |
PAGE_SIZE << il->hw_params.rx_page_order, |
| 348 |
DMA_FROM_DEVICE); |
| 349 |
if (unlikely(dma_mapping_error(&il->pci_dev->dev, page_dma))) { |
| 350 |
__free_pages(page, il->hw_params.rx_page_order); |
| 351 |
break; |
| 352 |
} |
| 353 |
|
| 354 |
spin_lock_irqsave(&rxq->lock, flags); |
| 355 |
|
| 356 |
if (list_empty(&rxq->rx_used)) { |
| 357 |
spin_unlock_irqrestore(&rxq->lock, flags); |
| 358 |
dma_unmap_page(&il->pci_dev->dev, page_dma, |
| 359 |
PAGE_SIZE << il->hw_params.rx_page_order, |
| 360 |
DMA_FROM_DEVICE); |
| 361 |
__free_pages(page, il->hw_params.rx_page_order); |
| 362 |
return; |
| 363 |
} |
| 364 |
|
| 365 |
element = rxq->rx_used.next; |
| 366 |
rxb = list_entry(element, struct il_rx_buf, list); |
| 367 |
list_del(element); |
| 368 |
|
| 369 |
BUG_ON(rxb->page); |
| 370 |
|
| 371 |
rxb->page = page; |
| 372 |
rxb->page_dma = page_dma; |
| 373 |
list_add_tail(&rxb->list, &rxq->rx_free); |
| 374 |
rxq->free_count++; |
| 375 |
il->alloc_rxb_page++; |
| 376 |
|
| 377 |
spin_unlock_irqrestore(&rxq->lock, flags); |
| 378 |
} |
| 379 |
} |
| 380 |
|
| 381 |
void |
| 382 |
il4965_rx_replenish(struct il_priv *il) |
| 383 |
{ |
| 384 |
unsigned long flags; |
| 385 |
|
| 386 |
il4965_rx_allocate(il, GFP_KERNEL); |
| 387 |
|
| 388 |
spin_lock_irqsave(&il->lock, flags); |
| 389 |
il4965_rx_queue_restock(il); |
| 390 |
spin_unlock_irqrestore(&il->lock, flags); |
| 391 |
} |
| 392 |
|
| 393 |
void |
| 394 |
il4965_rx_replenish_now(struct il_priv *il) |
| 395 |
{ |
| 396 |
il4965_rx_allocate(il, GFP_ATOMIC); |
| 397 |
|
| 398 |
il4965_rx_queue_restock(il); |
| 399 |
} |
| 400 |
|
| 401 |
/* Assumes that the skb field of the buffers in 'pool' is kept accurate. |
| 402 |
* If an SKB has been detached, the POOL needs to have its SKB set to NULL |
| 403 |
* This free routine walks the list of POOL entries and if SKB is set to |
| 404 |
* non NULL it is unmapped and freed |
| 405 |
*/ |
| 406 |
void |
| 407 |
il4965_rx_queue_free(struct il_priv *il, struct il_rx_queue *rxq) |
| 408 |
{ |
| 409 |
int i; |
| 410 |
for (i = 0; i < RX_QUEUE_SIZE + RX_FREE_BUFFERS; i++) { |
| 411 |
if (rxq->pool[i].page != NULL) { |
| 412 |
dma_unmap_page(&il->pci_dev->dev, |
| 413 |
rxq->pool[i].page_dma, |
| 414 |
PAGE_SIZE << il->hw_params.rx_page_order, |
| 415 |
DMA_FROM_DEVICE); |
| 416 |
__il_free_pages(il, rxq->pool[i].page); |
| 417 |
rxq->pool[i].page = NULL; |
| 418 |
} |
| 419 |
} |
| 420 |
|
| 421 |
dma_free_coherent(&il->pci_dev->dev, 4 * RX_QUEUE_SIZE, rxq->bd, |
| 422 |
rxq->bd_dma); |
| 423 |
dma_free_coherent(&il->pci_dev->dev, sizeof(struct il_rb_status), |
| 424 |
rxq->rb_stts, rxq->rb_stts_dma); |
| 425 |
rxq->bd = NULL; |
| 426 |
rxq->rb_stts = NULL; |
| 427 |
} |
| 428 |
|
| 429 |
int |
| 430 |
il4965_rxq_stop(struct il_priv *il) |
| 431 |
{ |
| 432 |
int ret; |
| 433 |
|
| 434 |
_il_wr(il, FH49_MEM_RCSR_CHNL0_CONFIG_REG, 0); |
| 435 |
ret = _il_poll_bit(il, FH49_MEM_RSSR_RX_STATUS_REG, |
| 436 |
FH49_RSSR_CHNL0_RX_STATUS_CHNL_IDLE, |
| 437 |
FH49_RSSR_CHNL0_RX_STATUS_CHNL_IDLE, |
| 438 |
1000); |
| 439 |
if (ret < 0) |
| 440 |
IL_ERR("Can't stop Rx DMA.\n"); |
| 441 |
|
| 442 |
return 0; |
| 443 |
} |
| 444 |
|
| 445 |
int |
| 446 |
il4965_hwrate_to_mac80211_idx(u32 rate_n_flags, enum nl80211_band band) |
| 447 |
{ |
| 448 |
int idx = 0; |
| 449 |
int band_offset = 0; |
| 450 |
|
| 451 |
/* HT rate format: mac80211 wants an MCS number, which is just LSB */ |
| 452 |
if (rate_n_flags & RATE_MCS_HT_MSK) { |
| 453 |
idx = (rate_n_flags & 0xff); |
| 454 |
return idx; |
| 455 |
/* Legacy rate format, search for match in table */ |
| 456 |
} else { |
| 457 |
if (band == NL80211_BAND_5GHZ) |
| 458 |
band_offset = IL_FIRST_OFDM_RATE; |
| 459 |
for (idx = band_offset; idx < RATE_COUNT_LEGACY; idx++) |
| 460 |
if (il_rates[idx].plcp == (rate_n_flags & 0xFF)) |
| 461 |
return idx - band_offset; |
| 462 |
} |
| 463 |
|
| 464 |
return -1; |
| 465 |
} |
| 466 |
|
| 467 |
static int |
| 468 |
il4965_calc_rssi(struct il_priv *il, struct il_rx_phy_res *rx_resp) |
| 469 |
{ |
| 470 |
/* data from PHY/DSP regarding signal strength, etc., |
| 471 |
* contents are always there, not configurable by host. */ |
| 472 |
struct il4965_rx_non_cfg_phy *ncphy = |
| 473 |
(struct il4965_rx_non_cfg_phy *)rx_resp->non_cfg_phy_buf; |
| 474 |
u32 agc = |
| 475 |
(le16_to_cpu(ncphy->agc_info) & IL49_AGC_DB_MASK) >> |
| 476 |
IL49_AGC_DB_POS; |
| 477 |
|
| 478 |
u32 valid_antennae = |
| 479 |
(le16_to_cpu(rx_resp->phy_flags) & IL49_RX_PHY_FLAGS_ANTENNAE_MASK) |
| 480 |
>> IL49_RX_PHY_FLAGS_ANTENNAE_OFFSET; |
| 481 |
u8 max_rssi = 0; |
| 482 |
u32 i; |
| 483 |
|
| 484 |
/* Find max rssi among 3 possible receivers. |
| 485 |
* These values are measured by the digital signal processor (DSP). |
| 486 |
* They should stay fairly constant even as the signal strength varies, |
| 487 |
* if the radio's automatic gain control (AGC) is working right. |
| 488 |
* AGC value (see below) will provide the "interesting" info. */ |
| 489 |
for (i = 0; i < 3; i++) |
| 490 |
if (valid_antennae & (1 << i)) |
| 491 |
max_rssi = max(ncphy->rssi_info[i << 1], max_rssi); |
| 492 |
|
| 493 |
D_STATS("Rssi In A %d B %d C %d Max %d AGC dB %d\n", |
| 494 |
ncphy->rssi_info[0], ncphy->rssi_info[2], ncphy->rssi_info[4], |
| 495 |
max_rssi, agc); |
| 496 |
|
| 497 |
/* dBm = max_rssi dB - agc dB - constant. |
| 498 |
* Higher AGC (higher radio gain) means lower signal. */ |
| 499 |
return max_rssi - agc - IL4965_RSSI_OFFSET; |
| 500 |
} |
| 501 |
|
| 502 |
static u32 |
| 503 |
il4965_translate_rx_status(struct il_priv *il, u32 decrypt_in) |
| 504 |
{ |
| 505 |
u32 decrypt_out = 0; |
| 506 |
|
| 507 |
if ((decrypt_in & RX_RES_STATUS_STATION_FOUND) == |
| 508 |
RX_RES_STATUS_STATION_FOUND) |
| 509 |
decrypt_out |= |
| 510 |
(RX_RES_STATUS_STATION_FOUND | |
| 511 |
RX_RES_STATUS_NO_STATION_INFO_MISMATCH); |
| 512 |
|
| 513 |
decrypt_out |= (decrypt_in & RX_RES_STATUS_SEC_TYPE_MSK); |
| 514 |
|
| 515 |
/* packet was not encrypted */ |
| 516 |
if ((decrypt_in & RX_RES_STATUS_SEC_TYPE_MSK) == |
| 517 |
RX_RES_STATUS_SEC_TYPE_NONE) |
| 518 |
return decrypt_out; |
| 519 |
|
| 520 |
/* packet was encrypted with unknown alg */ |
| 521 |
if ((decrypt_in & RX_RES_STATUS_SEC_TYPE_MSK) == |
| 522 |
RX_RES_STATUS_SEC_TYPE_ERR) |
| 523 |
return decrypt_out; |
| 524 |
|
| 525 |
/* decryption was not done in HW */ |
| 526 |
if ((decrypt_in & RX_MPDU_RES_STATUS_DEC_DONE_MSK) != |
| 527 |
RX_MPDU_RES_STATUS_DEC_DONE_MSK) |
| 528 |
return decrypt_out; |
| 529 |
|
| 530 |
switch (decrypt_in & RX_RES_STATUS_SEC_TYPE_MSK) { |
| 531 |
|
| 532 |
case RX_RES_STATUS_SEC_TYPE_CCMP: |
| 533 |
/* alg is CCM: check MIC only */ |
| 534 |
if (!(decrypt_in & RX_MPDU_RES_STATUS_MIC_OK)) |
| 535 |
/* Bad MIC */ |
| 536 |
decrypt_out |= RX_RES_STATUS_BAD_ICV_MIC; |
| 537 |
else |
| 538 |
decrypt_out |= RX_RES_STATUS_DECRYPT_OK; |
| 539 |
|
| 540 |
break; |
| 541 |
|
| 542 |
case RX_RES_STATUS_SEC_TYPE_TKIP: |
| 543 |
if (!(decrypt_in & RX_MPDU_RES_STATUS_TTAK_OK)) { |
| 544 |
/* Bad TTAK */ |
| 545 |
decrypt_out |= RX_RES_STATUS_BAD_KEY_TTAK; |
| 546 |
break; |
| 547 |
} |
| 548 |
fallthrough; /* if TTAK OK */ |
| 549 |
default: |
| 550 |
if (!(decrypt_in & RX_MPDU_RES_STATUS_ICV_OK)) |
| 551 |
decrypt_out |= RX_RES_STATUS_BAD_ICV_MIC; |
| 552 |
else |
| 553 |
decrypt_out |= RX_RES_STATUS_DECRYPT_OK; |
| 554 |
break; |
| 555 |
} |
| 556 |
|
| 557 |
D_RX("decrypt_in:0x%x decrypt_out = 0x%x\n", decrypt_in, decrypt_out); |
| 558 |
|
| 559 |
return decrypt_out; |
| 560 |
} |
| 561 |
|
| 562 |
#define SMALL_PACKET_SIZE 256 |
| 563 |
|
| 564 |
static void |
| 565 |
il4965_pass_packet_to_mac80211(struct il_priv *il, struct ieee80211_hdr *hdr, |
| 566 |
u32 len, u32 ampdu_status, struct il_rx_buf *rxb, |
| 567 |
struct ieee80211_rx_status *stats) |
| 568 |
{ |
| 569 |
struct sk_buff *skb; |
| 570 |
__le16 fc = hdr->frame_control; |
| 571 |
|
| 572 |
/* We only process data packets if the interface is open */ |
| 573 |
if (unlikely(!il->is_open)) { |
| 574 |
D_DROP("Dropping packet while interface is not open.\n"); |
| 575 |
return; |
| 576 |
} |
| 577 |
|
| 578 |
if (unlikely(test_bit(IL_STOP_REASON_PASSIVE, &il->stop_reason))) { |
| 579 |
il_wake_queues_by_reason(il, IL_STOP_REASON_PASSIVE); |
| 580 |
D_INFO("Woke queues - frame received on passive channel\n"); |
| 581 |
} |
| 582 |
|
| 583 |
/* In case of HW accelerated crypto and bad decryption, drop */ |
| 584 |
if (!il->cfg->mod_params->sw_crypto && |
| 585 |
il_set_decrypted_flag(il, hdr, ampdu_status, stats)) |
| 586 |
return; |
| 587 |
|
| 588 |
skb = dev_alloc_skb(SMALL_PACKET_SIZE); |
| 589 |
if (!skb) { |
| 590 |
IL_ERR("dev_alloc_skb failed\n"); |
| 591 |
return; |
| 592 |
} |
| 593 |
|
| 594 |
if (len <= SMALL_PACKET_SIZE) { |
| 595 |
skb_put_data(skb, hdr, len); |
| 596 |
} else { |
| 597 |
skb_add_rx_frag(skb, 0, rxb->page, (void *)hdr - rxb_addr(rxb), |
| 598 |
len, PAGE_SIZE << il->hw_params.rx_page_order); |
| 599 |
il->alloc_rxb_page--; |
| 600 |
rxb->page = NULL; |
| 601 |
} |
| 602 |
|
| 603 |
il_update_stats(il, false, fc, len); |
| 604 |
memcpy(IEEE80211_SKB_RXCB(skb), stats, sizeof(*stats)); |
| 605 |
|
| 606 |
ieee80211_rx(il->hw, skb); |
| 607 |
} |
| 608 |
|
| 609 |
/* Called for N_RX (legacy ABG frames), or |
| 610 |
* N_RX_MPDU (HT high-throughput N frames). */ |
| 611 |
static void |
| 612 |
il4965_hdl_rx(struct il_priv *il, struct il_rx_buf *rxb) |
| 613 |
{ |
| 614 |
struct ieee80211_hdr *header; |
| 615 |
struct ieee80211_rx_status rx_status = {}; |
| 616 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 617 |
struct il_rx_phy_res *phy_res; |
| 618 |
__le32 rx_pkt_status; |
| 619 |
struct il_rx_mpdu_res_start *amsdu; |
| 620 |
u32 len; |
| 621 |
u32 ampdu_status; |
| 622 |
u32 rate_n_flags; |
| 623 |
|
| 624 |
/** |
| 625 |
* N_RX and N_RX_MPDU are handled differently. |
| 626 |
* N_RX: physical layer info is in this buffer |
| 627 |
* N_RX_MPDU: physical layer info was sent in separate |
| 628 |
* command and cached in il->last_phy_res |
| 629 |
* |
| 630 |
* Here we set up local variables depending on which command is |
| 631 |
* received. |
| 632 |
*/ |
| 633 |
if (pkt->hdr.cmd == N_RX) { |
| 634 |
phy_res = (struct il_rx_phy_res *)pkt->u.raw; |
| 635 |
header = |
| 636 |
(struct ieee80211_hdr *)(pkt->u.raw + sizeof(*phy_res) + |
| 637 |
phy_res->cfg_phy_cnt); |
| 638 |
|
| 639 |
len = le16_to_cpu(phy_res->byte_count); |
| 640 |
rx_pkt_status = |
| 641 |
*(__le32 *) (pkt->u.raw + sizeof(*phy_res) + |
| 642 |
phy_res->cfg_phy_cnt + len); |
| 643 |
ampdu_status = le32_to_cpu(rx_pkt_status); |
| 644 |
} else { |
| 645 |
if (!il->_4965.last_phy_res_valid) { |
| 646 |
IL_ERR("MPDU frame without cached PHY data\n"); |
| 647 |
return; |
| 648 |
} |
| 649 |
phy_res = &il->_4965.last_phy_res; |
| 650 |
amsdu = (struct il_rx_mpdu_res_start *)pkt->u.raw; |
| 651 |
header = (struct ieee80211_hdr *)(pkt->u.raw + sizeof(*amsdu)); |
| 652 |
len = le16_to_cpu(amsdu->byte_count); |
| 653 |
rx_pkt_status = *(__le32 *) (pkt->u.raw + sizeof(*amsdu) + len); |
| 654 |
ampdu_status = |
| 655 |
il4965_translate_rx_status(il, le32_to_cpu(rx_pkt_status)); |
| 656 |
} |
| 657 |
|
| 658 |
if ((unlikely(phy_res->cfg_phy_cnt > 20))) { |
| 659 |
D_DROP("dsp size out of range [0,20]: %d\n", |
| 660 |
phy_res->cfg_phy_cnt); |
| 661 |
return; |
| 662 |
} |
| 663 |
|
| 664 |
if (!(rx_pkt_status & RX_RES_STATUS_NO_CRC32_ERROR) || |
| 665 |
!(rx_pkt_status & RX_RES_STATUS_NO_RXE_OVERFLOW)) { |
| 666 |
D_RX("Bad CRC or FIFO: 0x%08X.\n", le32_to_cpu(rx_pkt_status)); |
| 667 |
return; |
| 668 |
} |
| 669 |
|
| 670 |
/* This will be used in several places later */ |
| 671 |
rate_n_flags = le32_to_cpu(phy_res->rate_n_flags); |
| 672 |
|
| 673 |
/* rx_status carries information about the packet to mac80211 */ |
| 674 |
rx_status.mactime = le64_to_cpu(phy_res->timestamp); |
| 675 |
rx_status.band = |
| 676 |
(phy_res-> |
| 677 |
phy_flags & RX_RES_PHY_FLAGS_BAND_24_MSK) ? NL80211_BAND_2GHZ : |
| 678 |
NL80211_BAND_5GHZ; |
| 679 |
rx_status.freq = |
| 680 |
ieee80211_channel_to_frequency(le16_to_cpu(phy_res->channel), |
| 681 |
rx_status.band); |
| 682 |
rx_status.rate_idx = |
| 683 |
il4965_hwrate_to_mac80211_idx(rate_n_flags, rx_status.band); |
| 684 |
rx_status.flag = 0; |
| 685 |
|
| 686 |
/* TSF isn't reliable. In order to allow smooth user experience, |
| 687 |
* this W/A doesn't propagate it to the mac80211 */ |
| 688 |
/*rx_status.flag |= RX_FLAG_MACTIME_START; */ |
| 689 |
|
| 690 |
il->ucode_beacon_time = le32_to_cpu(phy_res->beacon_time_stamp); |
| 691 |
|
| 692 |
/* Find max signal strength (dBm) among 3 antenna/receiver chains */ |
| 693 |
rx_status.signal = il4965_calc_rssi(il, phy_res); |
| 694 |
|
| 695 |
D_STATS("Rssi %d, TSF %llu\n", rx_status.signal, |
| 696 |
(unsigned long long)rx_status.mactime); |
| 697 |
|
| 698 |
/* |
| 699 |
* "antenna number" |
| 700 |
* |
| 701 |
* It seems that the antenna field in the phy flags value |
| 702 |
* is actually a bit field. This is undefined by radiotap, |
| 703 |
* it wants an actual antenna number but I always get "7" |
| 704 |
* for most legacy frames I receive indicating that the |
| 705 |
* same frame was received on all three RX chains. |
| 706 |
* |
| 707 |
* I think this field should be removed in favor of a |
| 708 |
* new 802.11n radiotap field "RX chains" that is defined |
| 709 |
* as a bitmask. |
| 710 |
*/ |
| 711 |
rx_status.antenna = |
| 712 |
(le16_to_cpu(phy_res->phy_flags) & RX_RES_PHY_FLAGS_ANTENNA_MSK) >> |
| 713 |
RX_RES_PHY_FLAGS_ANTENNA_POS; |
| 714 |
|
| 715 |
/* set the preamble flag if appropriate */ |
| 716 |
if (phy_res->phy_flags & RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK) |
| 717 |
rx_status.enc_flags |= RX_ENC_FLAG_SHORTPRE; |
| 718 |
|
| 719 |
/* Set up the HT phy flags */ |
| 720 |
if (rate_n_flags & RATE_MCS_HT_MSK) |
| 721 |
rx_status.encoding = RX_ENC_HT; |
| 722 |
if (rate_n_flags & RATE_MCS_HT40_MSK) |
| 723 |
rx_status.bw = RATE_INFO_BW_40; |
| 724 |
else |
| 725 |
rx_status.bw = RATE_INFO_BW_20; |
| 726 |
if (rate_n_flags & RATE_MCS_SGI_MSK) |
| 727 |
rx_status.enc_flags |= RX_ENC_FLAG_SHORT_GI; |
| 728 |
|
| 729 |
if (phy_res->phy_flags & RX_RES_PHY_FLAGS_AGG_MSK) { |
| 730 |
/* We know which subframes of an A-MPDU belong |
| 731 |
* together since we get a single PHY response |
| 732 |
* from the firmware for all of them. |
| 733 |
*/ |
| 734 |
|
| 735 |
rx_status.flag |= RX_FLAG_AMPDU_DETAILS; |
| 736 |
rx_status.ampdu_reference = il->_4965.ampdu_ref; |
| 737 |
} |
| 738 |
|
| 739 |
il4965_pass_packet_to_mac80211(il, header, len, ampdu_status, rxb, |
| 740 |
&rx_status); |
| 741 |
} |
| 742 |
|
| 743 |
/* Cache phy data (Rx signal strength, etc) for HT frame (N_RX_PHY). |
| 744 |
* This will be used later in il_hdl_rx() for N_RX_MPDU. */ |
| 745 |
static void |
| 746 |
il4965_hdl_rx_phy(struct il_priv *il, struct il_rx_buf *rxb) |
| 747 |
{ |
| 748 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 749 |
il->_4965.last_phy_res_valid = true; |
| 750 |
il->_4965.ampdu_ref++; |
| 751 |
memcpy(&il->_4965.last_phy_res, pkt->u.raw, |
| 752 |
sizeof(struct il_rx_phy_res)); |
| 753 |
} |
| 754 |
|
| 755 |
static int |
| 756 |
il4965_get_channels_for_scan(struct il_priv *il, struct ieee80211_vif *vif, |
| 757 |
enum nl80211_band band, u8 is_active, |
| 758 |
u8 n_probes, struct il_scan_channel *scan_ch) |
| 759 |
{ |
| 760 |
struct ieee80211_channel *chan; |
| 761 |
const struct ieee80211_supported_band *sband; |
| 762 |
const struct il_channel_info *ch_info; |
| 763 |
u16 passive_dwell = 0; |
| 764 |
u16 active_dwell = 0; |
| 765 |
int added, i; |
| 766 |
u16 channel; |
| 767 |
|
| 768 |
sband = il_get_hw_mode(il, band); |
| 769 |
if (!sband) |
| 770 |
return 0; |
| 771 |
|
| 772 |
active_dwell = il_get_active_dwell_time(il, band, n_probes); |
| 773 |
passive_dwell = il_get_passive_dwell_time(il, band, vif); |
| 774 |
|
| 775 |
if (passive_dwell <= active_dwell) |
| 776 |
passive_dwell = active_dwell + 1; |
| 777 |
|
| 778 |
for (i = 0, added = 0; i < il->scan_request->n_channels; i++) { |
| 779 |
chan = il->scan_request->channels[i]; |
| 780 |
|
| 781 |
if (chan->band != band) |
| 782 |
continue; |
| 783 |
|
| 784 |
channel = chan->hw_value; |
| 785 |
scan_ch->channel = cpu_to_le16(channel); |
| 786 |
|
| 787 |
ch_info = il_get_channel_info(il, band, channel); |
| 788 |
if (!il_is_channel_valid(ch_info)) { |
| 789 |
D_SCAN("Channel %d is INVALID for this band.\n", |
| 790 |
channel); |
| 791 |
continue; |
| 792 |
} |
| 793 |
|
| 794 |
if (!is_active || il_is_channel_passive(ch_info) || |
| 795 |
(chan->flags & IEEE80211_CHAN_NO_IR)) |
| 796 |
scan_ch->type = SCAN_CHANNEL_TYPE_PASSIVE; |
| 797 |
else |
| 798 |
scan_ch->type = SCAN_CHANNEL_TYPE_ACTIVE; |
| 799 |
|
| 800 |
if (n_probes) |
| 801 |
scan_ch->type |= IL_SCAN_PROBE_MASK(n_probes); |
| 802 |
|
| 803 |
scan_ch->active_dwell = cpu_to_le16(active_dwell); |
| 804 |
scan_ch->passive_dwell = cpu_to_le16(passive_dwell); |
| 805 |
|
| 806 |
/* Set txpower levels to defaults */ |
| 807 |
scan_ch->dsp_atten = 110; |
| 808 |
|
| 809 |
/* NOTE: if we were doing 6Mb OFDM for scans we'd use |
| 810 |
* power level: |
| 811 |
* scan_ch->tx_gain = ((1 << 5) | (2 << 3)) | 3; |
| 812 |
*/ |
| 813 |
if (band == NL80211_BAND_5GHZ) |
| 814 |
scan_ch->tx_gain = ((1 << 5) | (3 << 3)) | 3; |
| 815 |
else |
| 816 |
scan_ch->tx_gain = ((1 << 5) | (5 << 3)); |
| 817 |
|
| 818 |
D_SCAN("Scanning ch=%d prob=0x%X [%s %d]\n", channel, |
| 819 |
le32_to_cpu(scan_ch->type), |
| 820 |
(scan_ch-> |
| 821 |
type & SCAN_CHANNEL_TYPE_ACTIVE) ? "ACTIVE" : "PASSIVE", |
| 822 |
(scan_ch-> |
| 823 |
type & SCAN_CHANNEL_TYPE_ACTIVE) ? active_dwell : |
| 824 |
passive_dwell); |
| 825 |
|
| 826 |
scan_ch++; |
| 827 |
added++; |
| 828 |
} |
| 829 |
|
| 830 |
D_SCAN("total channels to scan %d\n", added); |
| 831 |
return added; |
| 832 |
} |
| 833 |
|
| 834 |
static void |
| 835 |
il4965_toggle_tx_ant(struct il_priv *il, u8 *ant, u8 valid) |
| 836 |
{ |
| 837 |
int i; |
| 838 |
u8 ind = *ant; |
| 839 |
|
| 840 |
for (i = 0; i < RATE_ANT_NUM - 1; i++) { |
| 841 |
ind = (ind + 1) < RATE_ANT_NUM ? ind + 1 : 0; |
| 842 |
if (valid & BIT(ind)) { |
| 843 |
*ant = ind; |
| 844 |
return; |
| 845 |
} |
| 846 |
} |
| 847 |
} |
| 848 |
|
| 849 |
int |
| 850 |
il4965_request_scan(struct il_priv *il, struct ieee80211_vif *vif) |
| 851 |
{ |
| 852 |
struct il_host_cmd cmd = { |
| 853 |
.id = C_SCAN, |
| 854 |
.len = sizeof(struct il_scan_cmd), |
| 855 |
.flags = CMD_SIZE_HUGE, |
| 856 |
}; |
| 857 |
struct il_scan_cmd *scan; |
| 858 |
u32 rate_flags = 0; |
| 859 |
u16 cmd_len; |
| 860 |
u16 rx_chain = 0; |
| 861 |
enum nl80211_band band; |
| 862 |
u8 n_probes = 0; |
| 863 |
u8 rx_ant = il->hw_params.valid_rx_ant; |
| 864 |
u8 rate; |
| 865 |
bool is_active = false; |
| 866 |
int chan_mod; |
| 867 |
u8 active_chains; |
| 868 |
u8 scan_tx_antennas = il->hw_params.valid_tx_ant; |
| 869 |
int ret; |
| 870 |
|
| 871 |
lockdep_assert_held(&il->mutex); |
| 872 |
|
| 873 |
if (!il->scan_cmd) { |
| 874 |
il->scan_cmd = |
| 875 |
kmalloc(sizeof(struct il_scan_cmd) + IL_MAX_SCAN_SIZE, |
| 876 |
GFP_KERNEL); |
| 877 |
if (!il->scan_cmd) { |
| 878 |
D_SCAN("fail to allocate memory for scan\n"); |
| 879 |
return -ENOMEM; |
| 880 |
} |
| 881 |
} |
| 882 |
scan = il->scan_cmd; |
| 883 |
memset(scan, 0, sizeof(struct il_scan_cmd) + IL_MAX_SCAN_SIZE); |
| 884 |
|
| 885 |
scan->quiet_plcp_th = IL_PLCP_QUIET_THRESH; |
| 886 |
scan->quiet_time = IL_ACTIVE_QUIET_TIME; |
| 887 |
|
| 888 |
if (il_is_any_associated(il)) { |
| 889 |
u16 interval; |
| 890 |
u32 extra; |
| 891 |
u32 suspend_time = 100; |
| 892 |
u32 scan_suspend_time = 100; |
| 893 |
|
| 894 |
D_INFO("Scanning while associated...\n"); |
| 895 |
interval = vif->bss_conf.beacon_int; |
| 896 |
|
| 897 |
scan->suspend_time = 0; |
| 898 |
scan->max_out_time = cpu_to_le32(200 * 1024); |
| 899 |
if (!interval) |
| 900 |
interval = suspend_time; |
| 901 |
|
| 902 |
extra = (suspend_time / interval) << 22; |
| 903 |
scan_suspend_time = |
| 904 |
(extra | ((suspend_time % interval) * 1024)); |
| 905 |
scan->suspend_time = cpu_to_le32(scan_suspend_time); |
| 906 |
D_SCAN("suspend_time 0x%X beacon interval %d\n", |
| 907 |
scan_suspend_time, interval); |
| 908 |
} |
| 909 |
|
| 910 |
if (il->scan_request->n_ssids) { |
| 911 |
int i, p = 0; |
| 912 |
D_SCAN("Kicking off active scan\n"); |
| 913 |
for (i = 0; i < il->scan_request->n_ssids; i++) { |
| 914 |
/* always does wildcard anyway */ |
| 915 |
if (!il->scan_request->ssids[i].ssid_len) |
| 916 |
continue; |
| 917 |
scan->direct_scan[p].id = WLAN_EID_SSID; |
| 918 |
scan->direct_scan[p].len = |
| 919 |
il->scan_request->ssids[i].ssid_len; |
| 920 |
memcpy(scan->direct_scan[p].ssid, |
| 921 |
il->scan_request->ssids[i].ssid, |
| 922 |
il->scan_request->ssids[i].ssid_len); |
| 923 |
n_probes++; |
| 924 |
p++; |
| 925 |
} |
| 926 |
is_active = true; |
| 927 |
} else |
| 928 |
D_SCAN("Start passive scan.\n"); |
| 929 |
|
| 930 |
scan->tx_cmd.tx_flags = TX_CMD_FLG_SEQ_CTL_MSK; |
| 931 |
scan->tx_cmd.sta_id = il->hw_params.bcast_id; |
| 932 |
scan->tx_cmd.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE; |
| 933 |
|
| 934 |
switch (il->scan_band) { |
| 935 |
case NL80211_BAND_2GHZ: |
| 936 |
scan->flags = RXON_FLG_BAND_24G_MSK | RXON_FLG_AUTO_DETECT_MSK; |
| 937 |
chan_mod = |
| 938 |
le32_to_cpu(il->active.flags & RXON_FLG_CHANNEL_MODE_MSK) >> |
| 939 |
RXON_FLG_CHANNEL_MODE_POS; |
| 940 |
if (chan_mod == CHANNEL_MODE_PURE_40) { |
| 941 |
rate = RATE_6M_PLCP; |
| 942 |
} else { |
| 943 |
rate = RATE_1M_PLCP; |
| 944 |
rate_flags = RATE_MCS_CCK_MSK; |
| 945 |
} |
| 946 |
break; |
| 947 |
case NL80211_BAND_5GHZ: |
| 948 |
rate = RATE_6M_PLCP; |
| 949 |
break; |
| 950 |
default: |
| 951 |
IL_WARN("Invalid scan band\n"); |
| 952 |
return -EIO; |
| 953 |
} |
| 954 |
|
| 955 |
/* |
| 956 |
* If active scanning is requested but a certain channel is |
| 957 |
* marked passive, we can do active scanning if we detect |
| 958 |
* transmissions. |
| 959 |
* |
| 960 |
* There is an issue with some firmware versions that triggers |
| 961 |
* a sysassert on a "good CRC threshold" of zero (== disabled), |
| 962 |
* on a radar channel even though this means that we should NOT |
| 963 |
* send probes. |
| 964 |
* |
| 965 |
* The "good CRC threshold" is the number of frames that we |
| 966 |
* need to receive during our dwell time on a channel before |
| 967 |
* sending out probes -- setting this to a huge value will |
| 968 |
* mean we never reach it, but at the same time work around |
| 969 |
* the aforementioned issue. Thus use IL_GOOD_CRC_TH_NEVER |
| 970 |
* here instead of IL_GOOD_CRC_TH_DISABLED. |
| 971 |
*/ |
| 972 |
scan->good_CRC_th = |
| 973 |
is_active ? IL_GOOD_CRC_TH_DEFAULT : IL_GOOD_CRC_TH_NEVER; |
| 974 |
|
| 975 |
band = il->scan_band; |
| 976 |
|
| 977 |
if (il->cfg->scan_rx_antennas[band]) |
| 978 |
rx_ant = il->cfg->scan_rx_antennas[band]; |
| 979 |
|
| 980 |
il4965_toggle_tx_ant(il, &il->scan_tx_ant[band], scan_tx_antennas); |
| 981 |
rate_flags |= BIT(il->scan_tx_ant[band]) << RATE_MCS_ANT_POS; |
| 982 |
scan->tx_cmd.rate_n_flags = cpu_to_le32(rate | rate_flags); |
| 983 |
|
| 984 |
/* In power save mode use one chain, otherwise use all chains */ |
| 985 |
if (test_bit(S_POWER_PMI, &il->status)) { |
| 986 |
/* rx_ant has been set to all valid chains previously */ |
| 987 |
active_chains = |
| 988 |
rx_ant & ((u8) (il->chain_noise_data.active_chains)); |
| 989 |
if (!active_chains) |
| 990 |
active_chains = rx_ant; |
| 991 |
|
| 992 |
D_SCAN("chain_noise_data.active_chains: %u\n", |
| 993 |
il->chain_noise_data.active_chains); |
| 994 |
|
| 995 |
rx_ant = il4965_first_antenna(active_chains); |
| 996 |
} |
| 997 |
|
| 998 |
/* MIMO is not used here, but value is required */ |
| 999 |
rx_chain |= il->hw_params.valid_rx_ant << RXON_RX_CHAIN_VALID_POS; |
| 1000 |
rx_chain |= rx_ant << RXON_RX_CHAIN_FORCE_MIMO_SEL_POS; |
| 1001 |
rx_chain |= rx_ant << RXON_RX_CHAIN_FORCE_SEL_POS; |
| 1002 |
rx_chain |= 0x1 << RXON_RX_CHAIN_DRIVER_FORCE_POS; |
| 1003 |
scan->rx_chain = cpu_to_le16(rx_chain); |
| 1004 |
|
| 1005 |
cmd_len = |
| 1006 |
il_fill_probe_req(il, (struct ieee80211_mgmt *)scan->data, |
| 1007 |
vif->addr, il->scan_request->ie, |
| 1008 |
il->scan_request->ie_len, |
| 1009 |
IL_MAX_SCAN_SIZE - sizeof(*scan)); |
| 1010 |
scan->tx_cmd.len = cpu_to_le16(cmd_len); |
| 1011 |
|
| 1012 |
scan->filter_flags |= |
| 1013 |
(RXON_FILTER_ACCEPT_GRP_MSK | RXON_FILTER_BCON_AWARE_MSK); |
| 1014 |
|
| 1015 |
scan->channel_count = |
| 1016 |
il4965_get_channels_for_scan(il, vif, band, is_active, n_probes, |
| 1017 |
(void *)&scan->data[cmd_len]); |
| 1018 |
if (scan->channel_count == 0) { |
| 1019 |
D_SCAN("channel count %d\n", scan->channel_count); |
| 1020 |
return -EIO; |
| 1021 |
} |
| 1022 |
|
| 1023 |
cmd.len += |
| 1024 |
le16_to_cpu(scan->tx_cmd.len) + |
| 1025 |
scan->channel_count * sizeof(struct il_scan_channel); |
| 1026 |
cmd.data = scan; |
| 1027 |
scan->len = cpu_to_le16(cmd.len); |
| 1028 |
|
| 1029 |
set_bit(S_SCAN_HW, &il->status); |
| 1030 |
|
| 1031 |
ret = il_send_cmd_sync(il, &cmd); |
| 1032 |
if (ret) |
| 1033 |
clear_bit(S_SCAN_HW, &il->status); |
| 1034 |
|
| 1035 |
return ret; |
| 1036 |
} |
| 1037 |
|
| 1038 |
int |
| 1039 |
il4965_manage_ibss_station(struct il_priv *il, struct ieee80211_vif *vif, |
| 1040 |
bool add) |
| 1041 |
{ |
| 1042 |
struct il_vif_priv *vif_priv = (void *)vif->drv_priv; |
| 1043 |
|
| 1044 |
if (add) |
| 1045 |
return il4965_add_bssid_station(il, vif->bss_conf.bssid, |
| 1046 |
&vif_priv->ibss_bssid_sta_id); |
| 1047 |
return il_remove_station(il, vif_priv->ibss_bssid_sta_id, |
| 1048 |
vif->bss_conf.bssid); |
| 1049 |
} |
| 1050 |
|
| 1051 |
void |
| 1052 |
il4965_free_tfds_in_queue(struct il_priv *il, int sta_id, int tid, int freed) |
| 1053 |
{ |
| 1054 |
lockdep_assert_held(&il->sta_lock); |
| 1055 |
|
| 1056 |
if (il->stations[sta_id].tid[tid].tfds_in_queue >= freed) |
| 1057 |
il->stations[sta_id].tid[tid].tfds_in_queue -= freed; |
| 1058 |
else { |
| 1059 |
D_TX("free more than tfds_in_queue (%u:%d)\n", |
| 1060 |
il->stations[sta_id].tid[tid].tfds_in_queue, freed); |
| 1061 |
il->stations[sta_id].tid[tid].tfds_in_queue = 0; |
| 1062 |
} |
| 1063 |
} |
| 1064 |
|
| 1065 |
#define IL_TX_QUEUE_MSK 0xfffff |
| 1066 |
|
| 1067 |
static bool |
| 1068 |
il4965_is_single_rx_stream(struct il_priv *il) |
| 1069 |
{ |
| 1070 |
return il->current_ht_config.smps == IEEE80211_SMPS_STATIC || |
| 1071 |
il->current_ht_config.single_chain_sufficient; |
| 1072 |
} |
| 1073 |
|
| 1074 |
#define IL_NUM_RX_CHAINS_MULTIPLE 3 |
| 1075 |
#define IL_NUM_RX_CHAINS_SINGLE 2 |
| 1076 |
#define IL_NUM_IDLE_CHAINS_DUAL 2 |
| 1077 |
#define IL_NUM_IDLE_CHAINS_SINGLE 1 |
| 1078 |
|
| 1079 |
/* |
| 1080 |
* Determine how many receiver/antenna chains to use. |
| 1081 |
* |
| 1082 |
* More provides better reception via diversity. Fewer saves power |
| 1083 |
* at the expense of throughput, but only when not in powersave to |
| 1084 |
* start with. |
| 1085 |
* |
| 1086 |
* MIMO (dual stream) requires at least 2, but works better with 3. |
| 1087 |
* This does not determine *which* chains to use, just how many. |
| 1088 |
*/ |
| 1089 |
static int |
| 1090 |
il4965_get_active_rx_chain_count(struct il_priv *il) |
| 1091 |
{ |
| 1092 |
/* # of Rx chains to use when expecting MIMO. */ |
| 1093 |
if (il4965_is_single_rx_stream(il)) |
| 1094 |
return IL_NUM_RX_CHAINS_SINGLE; |
| 1095 |
else |
| 1096 |
return IL_NUM_RX_CHAINS_MULTIPLE; |
| 1097 |
} |
| 1098 |
|
| 1099 |
/* |
| 1100 |
* When we are in power saving mode, unless device support spatial |
| 1101 |
* multiplexing power save, use the active count for rx chain count. |
| 1102 |
*/ |
| 1103 |
static int |
| 1104 |
il4965_get_idle_rx_chain_count(struct il_priv *il, int active_cnt) |
| 1105 |
{ |
| 1106 |
/* # Rx chains when idling, depending on SMPS mode */ |
| 1107 |
switch (il->current_ht_config.smps) { |
| 1108 |
case IEEE80211_SMPS_STATIC: |
| 1109 |
case IEEE80211_SMPS_DYNAMIC: |
| 1110 |
return IL_NUM_IDLE_CHAINS_SINGLE; |
| 1111 |
case IEEE80211_SMPS_OFF: |
| 1112 |
return active_cnt; |
| 1113 |
default: |
| 1114 |
WARN(1, "invalid SMPS mode %d", il->current_ht_config.smps); |
| 1115 |
return active_cnt; |
| 1116 |
} |
| 1117 |
} |
| 1118 |
|
| 1119 |
/* up to 4 chains */ |
| 1120 |
static u8 |
| 1121 |
il4965_count_chain_bitmap(u32 chain_bitmap) |
| 1122 |
{ |
| 1123 |
u8 res; |
| 1124 |
res = (chain_bitmap & BIT(0)) >> 0; |
| 1125 |
res += (chain_bitmap & BIT(1)) >> 1; |
| 1126 |
res += (chain_bitmap & BIT(2)) >> 2; |
| 1127 |
res += (chain_bitmap & BIT(3)) >> 3; |
| 1128 |
return res; |
| 1129 |
} |
| 1130 |
|
| 1131 |
/* |
| 1132 |
* il4965_set_rxon_chain - Set up Rx chain usage in "staging" RXON image |
| 1133 |
* |
| 1134 |
* Selects how many and which Rx receivers/antennas/chains to use. |
| 1135 |
* This should not be used for scan command ... it puts data in wrong place. |
| 1136 |
*/ |
| 1137 |
void |
| 1138 |
il4965_set_rxon_chain(struct il_priv *il) |
| 1139 |
{ |
| 1140 |
bool is_single = il4965_is_single_rx_stream(il); |
| 1141 |
bool is_cam = !test_bit(S_POWER_PMI, &il->status); |
| 1142 |
u8 idle_rx_cnt, active_rx_cnt, valid_rx_cnt; |
| 1143 |
u32 active_chains; |
| 1144 |
u16 rx_chain; |
| 1145 |
|
| 1146 |
/* Tell uCode which antennas are actually connected. |
| 1147 |
* Before first association, we assume all antennas are connected. |
| 1148 |
* Just after first association, il4965_chain_noise_calibration() |
| 1149 |
* checks which antennas actually *are* connected. */ |
| 1150 |
if (il->chain_noise_data.active_chains) |
| 1151 |
active_chains = il->chain_noise_data.active_chains; |
| 1152 |
else |
| 1153 |
active_chains = il->hw_params.valid_rx_ant; |
| 1154 |
|
| 1155 |
rx_chain = active_chains << RXON_RX_CHAIN_VALID_POS; |
| 1156 |
|
| 1157 |
/* How many receivers should we use? */ |
| 1158 |
active_rx_cnt = il4965_get_active_rx_chain_count(il); |
| 1159 |
idle_rx_cnt = il4965_get_idle_rx_chain_count(il, active_rx_cnt); |
| 1160 |
|
| 1161 |
/* correct rx chain count according hw settings |
| 1162 |
* and chain noise calibration |
| 1163 |
*/ |
| 1164 |
valid_rx_cnt = il4965_count_chain_bitmap(active_chains); |
| 1165 |
if (valid_rx_cnt < active_rx_cnt) |
| 1166 |
active_rx_cnt = valid_rx_cnt; |
| 1167 |
|
| 1168 |
if (valid_rx_cnt < idle_rx_cnt) |
| 1169 |
idle_rx_cnt = valid_rx_cnt; |
| 1170 |
|
| 1171 |
rx_chain |= active_rx_cnt << RXON_RX_CHAIN_MIMO_CNT_POS; |
| 1172 |
rx_chain |= idle_rx_cnt << RXON_RX_CHAIN_CNT_POS; |
| 1173 |
|
| 1174 |
il->staging.rx_chain = cpu_to_le16(rx_chain); |
| 1175 |
|
| 1176 |
if (!is_single && active_rx_cnt >= IL_NUM_RX_CHAINS_SINGLE && is_cam) |
| 1177 |
il->staging.rx_chain |= RXON_RX_CHAIN_MIMO_FORCE_MSK; |
| 1178 |
else |
| 1179 |
il->staging.rx_chain &= ~RXON_RX_CHAIN_MIMO_FORCE_MSK; |
| 1180 |
|
| 1181 |
D_ASSOC("rx_chain=0x%X active=%d idle=%d\n", il->staging.rx_chain, |
| 1182 |
active_rx_cnt, idle_rx_cnt); |
| 1183 |
|
| 1184 |
WARN_ON(active_rx_cnt == 0 || idle_rx_cnt == 0 || |
| 1185 |
active_rx_cnt < idle_rx_cnt); |
| 1186 |
} |
| 1187 |
|
| 1188 |
static const char * |
| 1189 |
il4965_get_fh_string(int cmd) |
| 1190 |
{ |
| 1191 |
switch (cmd) { |
| 1192 |
IL_CMD(FH49_RSCSR_CHNL0_STTS_WPTR_REG); |
| 1193 |
IL_CMD(FH49_RSCSR_CHNL0_RBDCB_BASE_REG); |
| 1194 |
IL_CMD(FH49_RSCSR_CHNL0_WPTR); |
| 1195 |
IL_CMD(FH49_MEM_RCSR_CHNL0_CONFIG_REG); |
| 1196 |
IL_CMD(FH49_MEM_RSSR_SHARED_CTRL_REG); |
| 1197 |
IL_CMD(FH49_MEM_RSSR_RX_STATUS_REG); |
| 1198 |
IL_CMD(FH49_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV); |
| 1199 |
IL_CMD(FH49_TSSR_TX_STATUS_REG); |
| 1200 |
IL_CMD(FH49_TSSR_TX_ERROR_REG); |
| 1201 |
default: |
| 1202 |
return "UNKNOWN"; |
| 1203 |
} |
| 1204 |
} |
| 1205 |
|
| 1206 |
int |
| 1207 |
il4965_dump_fh(struct il_priv *il, char **buf, bool display) |
| 1208 |
{ |
| 1209 |
int i; |
| 1210 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 1211 |
int pos = 0; |
| 1212 |
size_t bufsz = 0; |
| 1213 |
#endif |
| 1214 |
static const u32 fh_tbl[] = { |
| 1215 |
FH49_RSCSR_CHNL0_STTS_WPTR_REG, |
| 1216 |
FH49_RSCSR_CHNL0_RBDCB_BASE_REG, |
| 1217 |
FH49_RSCSR_CHNL0_WPTR, |
| 1218 |
FH49_MEM_RCSR_CHNL0_CONFIG_REG, |
| 1219 |
FH49_MEM_RSSR_SHARED_CTRL_REG, |
| 1220 |
FH49_MEM_RSSR_RX_STATUS_REG, |
| 1221 |
FH49_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV, |
| 1222 |
FH49_TSSR_TX_STATUS_REG, |
| 1223 |
FH49_TSSR_TX_ERROR_REG |
| 1224 |
}; |
| 1225 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 1226 |
if (display) { |
| 1227 |
bufsz = ARRAY_SIZE(fh_tbl) * 48 + 40; |
| 1228 |
*buf = kmalloc(bufsz, GFP_KERNEL); |
| 1229 |
if (!*buf) |
| 1230 |
return -ENOMEM; |
| 1231 |
pos += |
| 1232 |
scnprintf(*buf + pos, bufsz - pos, "FH register values:\n"); |
| 1233 |
for (i = 0; i < ARRAY_SIZE(fh_tbl); i++) { |
| 1234 |
pos += |
| 1235 |
scnprintf(*buf + pos, bufsz - pos, |
| 1236 |
" %34s: 0X%08x\n", |
| 1237 |
il4965_get_fh_string(fh_tbl[i]), |
| 1238 |
il_rd(il, fh_tbl[i])); |
| 1239 |
} |
| 1240 |
return pos; |
| 1241 |
} |
| 1242 |
#endif |
| 1243 |
IL_ERR("FH register values:\n"); |
| 1244 |
for (i = 0; i < ARRAY_SIZE(fh_tbl); i++) { |
| 1245 |
IL_ERR(" %34s: 0X%08x\n", il4965_get_fh_string(fh_tbl[i]), |
| 1246 |
il_rd(il, fh_tbl[i])); |
| 1247 |
} |
| 1248 |
return 0; |
| 1249 |
} |
| 1250 |
|
| 1251 |
static void |
| 1252 |
il4965_hdl_missed_beacon(struct il_priv *il, struct il_rx_buf *rxb) |
| 1253 |
{ |
| 1254 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 1255 |
struct il_missed_beacon_notif *missed_beacon; |
| 1256 |
|
| 1257 |
missed_beacon = &pkt->u.missed_beacon; |
| 1258 |
if (le32_to_cpu(missed_beacon->consecutive_missed_beacons) > |
| 1259 |
il->missed_beacon_threshold) { |
| 1260 |
D_CALIB("missed bcn cnsq %d totl %d rcd %d expctd %d\n", |
| 1261 |
le32_to_cpu(missed_beacon->consecutive_missed_beacons), |
| 1262 |
le32_to_cpu(missed_beacon->total_missed_becons), |
| 1263 |
le32_to_cpu(missed_beacon->num_recvd_beacons), |
| 1264 |
le32_to_cpu(missed_beacon->num_expected_beacons)); |
| 1265 |
if (!test_bit(S_SCANNING, &il->status)) |
| 1266 |
il4965_init_sensitivity(il); |
| 1267 |
} |
| 1268 |
} |
| 1269 |
|
| 1270 |
/* Calculate noise level, based on measurements during network silence just |
| 1271 |
* before arriving beacon. This measurement can be done only if we know |
| 1272 |
* exactly when to expect beacons, therefore only when we're associated. */ |
| 1273 |
static void |
| 1274 |
il4965_rx_calc_noise(struct il_priv *il) |
| 1275 |
{ |
| 1276 |
struct stats_rx_non_phy *rx_info; |
| 1277 |
int num_active_rx = 0; |
| 1278 |
int total_silence = 0; |
| 1279 |
int bcn_silence_a, bcn_silence_b, bcn_silence_c; |
| 1280 |
int last_rx_noise; |
| 1281 |
|
| 1282 |
rx_info = &(il->_4965.stats.rx.general); |
| 1283 |
bcn_silence_a = |
| 1284 |
le32_to_cpu(rx_info->beacon_silence_rssi_a) & IN_BAND_FILTER; |
| 1285 |
bcn_silence_b = |
| 1286 |
le32_to_cpu(rx_info->beacon_silence_rssi_b) & IN_BAND_FILTER; |
| 1287 |
bcn_silence_c = |
| 1288 |
le32_to_cpu(rx_info->beacon_silence_rssi_c) & IN_BAND_FILTER; |
| 1289 |
|
| 1290 |
if (bcn_silence_a) { |
| 1291 |
total_silence += bcn_silence_a; |
| 1292 |
num_active_rx++; |
| 1293 |
} |
| 1294 |
if (bcn_silence_b) { |
| 1295 |
total_silence += bcn_silence_b; |
| 1296 |
num_active_rx++; |
| 1297 |
} |
| 1298 |
if (bcn_silence_c) { |
| 1299 |
total_silence += bcn_silence_c; |
| 1300 |
num_active_rx++; |
| 1301 |
} |
| 1302 |
|
| 1303 |
/* Average among active antennas */ |
| 1304 |
if (num_active_rx) |
| 1305 |
last_rx_noise = (total_silence / num_active_rx) - 107; |
| 1306 |
else |
| 1307 |
last_rx_noise = IL_NOISE_MEAS_NOT_AVAILABLE; |
| 1308 |
|
| 1309 |
D_CALIB("inband silence a %u, b %u, c %u, dBm %d\n", bcn_silence_a, |
| 1310 |
bcn_silence_b, bcn_silence_c, last_rx_noise); |
| 1311 |
} |
| 1312 |
|
| 1313 |
#ifdef CONFIG_IWLEGACY_DEBUGFS |
| 1314 |
/* |
| 1315 |
* based on the assumption of all stats counter are in DWORD |
| 1316 |
* FIXME: This function is for debugging, do not deal with |
| 1317 |
* the case of counters roll-over. |
| 1318 |
*/ |
| 1319 |
static void |
| 1320 |
il4965_accumulative_stats(struct il_priv *il, __le32 * stats) |
| 1321 |
{ |
| 1322 |
int i, size; |
| 1323 |
__le32 *prev_stats; |
| 1324 |
u32 *accum_stats; |
| 1325 |
u32 *delta, *max_delta; |
| 1326 |
struct stats_general_common *general, *accum_general; |
| 1327 |
|
| 1328 |
prev_stats = (__le32 *) &il->_4965.stats; |
| 1329 |
accum_stats = (u32 *) &il->_4965.accum_stats; |
| 1330 |
size = sizeof(struct il_notif_stats); |
| 1331 |
general = &il->_4965.stats.general.common; |
| 1332 |
accum_general = &il->_4965.accum_stats.general.common; |
| 1333 |
delta = (u32 *) &il->_4965.delta_stats; |
| 1334 |
max_delta = (u32 *) &il->_4965.max_delta; |
| 1335 |
|
| 1336 |
for (i = sizeof(__le32); i < size; |
| 1337 |
i += |
| 1338 |
sizeof(__le32), stats++, prev_stats++, delta++, max_delta++, |
| 1339 |
accum_stats++) { |
| 1340 |
if (le32_to_cpu(*stats) > le32_to_cpu(*prev_stats)) { |
| 1341 |
*delta = |
| 1342 |
(le32_to_cpu(*stats) - le32_to_cpu(*prev_stats)); |
| 1343 |
*accum_stats += *delta; |
| 1344 |
if (*delta > *max_delta) |
| 1345 |
*max_delta = *delta; |
| 1346 |
} |
| 1347 |
} |
| 1348 |
|
| 1349 |
/* reset accumulative stats for "no-counter" type stats */ |
| 1350 |
accum_general->temperature = general->temperature; |
| 1351 |
accum_general->ttl_timestamp = general->ttl_timestamp; |
| 1352 |
} |
| 1353 |
#endif |
| 1354 |
|
| 1355 |
static void |
| 1356 |
il4965_hdl_stats(struct il_priv *il, struct il_rx_buf *rxb) |
| 1357 |
{ |
| 1358 |
const int recalib_seconds = 60; |
| 1359 |
bool change; |
| 1360 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 1361 |
|
| 1362 |
D_RX("Statistics notification received (%d vs %d).\n", |
| 1363 |
(int)sizeof(struct il_notif_stats), |
| 1364 |
le32_to_cpu(pkt->len_n_flags) & IL_RX_FRAME_SIZE_MSK); |
| 1365 |
|
| 1366 |
change = |
| 1367 |
((il->_4965.stats.general.common.temperature != |
| 1368 |
pkt->u.stats.general.common.temperature) || |
| 1369 |
((il->_4965.stats.flag & STATS_REPLY_FLG_HT40_MODE_MSK) != |
| 1370 |
(pkt->u.stats.flag & STATS_REPLY_FLG_HT40_MODE_MSK))); |
| 1371 |
#ifdef CONFIG_IWLEGACY_DEBUGFS |
| 1372 |
il4965_accumulative_stats(il, (__le32 *) &pkt->u.stats); |
| 1373 |
#endif |
| 1374 |
|
| 1375 |
/* TODO: reading some of stats is unneeded */ |
| 1376 |
memcpy(&il->_4965.stats, &pkt->u.stats, sizeof(il->_4965.stats)); |
| 1377 |
|
| 1378 |
set_bit(S_STATS, &il->status); |
| 1379 |
|
| 1380 |
/* |
| 1381 |
* Reschedule the stats timer to occur in recalib_seconds to ensure |
| 1382 |
* we get a thermal update even if the uCode doesn't give us one |
| 1383 |
*/ |
| 1384 |
mod_timer(&il->stats_periodic, |
| 1385 |
jiffies + secs_to_jiffies(recalib_seconds)); |
| 1386 |
|
| 1387 |
if (unlikely(!test_bit(S_SCANNING, &il->status)) && |
| 1388 |
(pkt->hdr.cmd == N_STATS)) { |
| 1389 |
il4965_rx_calc_noise(il); |
| 1390 |
queue_work(il->workqueue, &il->run_time_calib_work); |
| 1391 |
} |
| 1392 |
|
| 1393 |
if (change) |
| 1394 |
il4965_temperature_calib(il); |
| 1395 |
} |
| 1396 |
|
| 1397 |
static void |
| 1398 |
il4965_hdl_c_stats(struct il_priv *il, struct il_rx_buf *rxb) |
| 1399 |
{ |
| 1400 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 1401 |
|
| 1402 |
if (le32_to_cpu(pkt->u.stats.flag) & UCODE_STATS_CLEAR_MSK) { |
| 1403 |
#ifdef CONFIG_IWLEGACY_DEBUGFS |
| 1404 |
memset(&il->_4965.accum_stats, 0, |
| 1405 |
sizeof(struct il_notif_stats)); |
| 1406 |
memset(&il->_4965.delta_stats, 0, |
| 1407 |
sizeof(struct il_notif_stats)); |
| 1408 |
memset(&il->_4965.max_delta, 0, sizeof(struct il_notif_stats)); |
| 1409 |
#endif |
| 1410 |
D_RX("Statistics have been cleared\n"); |
| 1411 |
} |
| 1412 |
il4965_hdl_stats(il, rxb); |
| 1413 |
} |
| 1414 |
|
| 1415 |
|
| 1416 |
/* |
| 1417 |
* mac80211 queues, ACs, hardware queues, FIFOs. |
| 1418 |
* |
| 1419 |
* Cf. https://wireless.wiki.kernel.org/en/developers/Documentation/mac80211/queues |
| 1420 |
* |
| 1421 |
* Mac80211 uses the following numbers, which we get as from it |
| 1422 |
* by way of skb_get_queue_mapping(skb): |
| 1423 |
* |
| 1424 |
* VO 0 |
| 1425 |
* VI 1 |
| 1426 |
* BE 2 |
| 1427 |
* BK 3 |
| 1428 |
* |
| 1429 |
* |
| 1430 |
* Regular (not A-MPDU) frames are put into hardware queues corresponding |
| 1431 |
* to the FIFOs, see comments in iwl-prph.h. Aggregated frames get their |
| 1432 |
* own queue per aggregation session (RA/TID combination), such queues are |
| 1433 |
* set up to map into FIFOs too, for which we need an AC->FIFO mapping. In |
| 1434 |
* order to map frames to the right queue, we also need an AC->hw queue |
| 1435 |
* mapping. This is implemented here. |
| 1436 |
* |
| 1437 |
* Due to the way hw queues are set up (by the hw specific modules like |
| 1438 |
* 4965.c), the AC->hw queue mapping is the identity |
| 1439 |
* mapping. |
| 1440 |
*/ |
| 1441 |
|
| 1442 |
static const u8 tid_to_ac[] = { |
| 1443 |
IEEE80211_AC_BE, |
| 1444 |
IEEE80211_AC_BK, |
| 1445 |
IEEE80211_AC_BK, |
| 1446 |
IEEE80211_AC_BE, |
| 1447 |
IEEE80211_AC_VI, |
| 1448 |
IEEE80211_AC_VI, |
| 1449 |
IEEE80211_AC_VO, |
| 1450 |
IEEE80211_AC_VO |
| 1451 |
}; |
| 1452 |
|
| 1453 |
static inline int |
| 1454 |
il4965_get_ac_from_tid(u16 tid) |
| 1455 |
{ |
| 1456 |
if (likely(tid < ARRAY_SIZE(tid_to_ac))) |
| 1457 |
return tid_to_ac[tid]; |
| 1458 |
|
| 1459 |
/* no support for TIDs 8-15 yet */ |
| 1460 |
return -EINVAL; |
| 1461 |
} |
| 1462 |
|
| 1463 |
static inline int |
| 1464 |
il4965_get_fifo_from_tid(u16 tid) |
| 1465 |
{ |
| 1466 |
static const u8 ac_to_fifo[] = { |
| 1467 |
IL_TX_FIFO_VO, |
| 1468 |
IL_TX_FIFO_VI, |
| 1469 |
IL_TX_FIFO_BE, |
| 1470 |
IL_TX_FIFO_BK, |
| 1471 |
}; |
| 1472 |
|
| 1473 |
if (likely(tid < ARRAY_SIZE(tid_to_ac))) |
| 1474 |
return ac_to_fifo[tid_to_ac[tid]]; |
| 1475 |
|
| 1476 |
/* no support for TIDs 8-15 yet */ |
| 1477 |
return -EINVAL; |
| 1478 |
} |
| 1479 |
|
| 1480 |
/* |
| 1481 |
* handle build C_TX command notification. |
| 1482 |
*/ |
| 1483 |
static void |
| 1484 |
il4965_tx_cmd_build_basic(struct il_priv *il, struct sk_buff *skb, |
| 1485 |
struct il_tx_cmd *tx_cmd, |
| 1486 |
struct ieee80211_tx_info *info, |
| 1487 |
struct ieee80211_hdr *hdr, u8 std_id) |
| 1488 |
{ |
| 1489 |
__le16 fc = hdr->frame_control; |
| 1490 |
__le32 tx_flags = tx_cmd->tx_flags; |
| 1491 |
|
| 1492 |
tx_cmd->stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE; |
| 1493 |
if (!(info->flags & IEEE80211_TX_CTL_NO_ACK)) { |
| 1494 |
tx_flags |= TX_CMD_FLG_ACK_MSK; |
| 1495 |
if (ieee80211_is_mgmt(fc)) |
| 1496 |
tx_flags |= TX_CMD_FLG_SEQ_CTL_MSK; |
| 1497 |
if (ieee80211_is_probe_resp(fc) && |
| 1498 |
!(le16_to_cpu(hdr->seq_ctrl) & 0xf)) |
| 1499 |
tx_flags |= TX_CMD_FLG_TSF_MSK; |
| 1500 |
} else { |
| 1501 |
tx_flags &= (~TX_CMD_FLG_ACK_MSK); |
| 1502 |
tx_flags |= TX_CMD_FLG_SEQ_CTL_MSK; |
| 1503 |
} |
| 1504 |
|
| 1505 |
if (ieee80211_is_back_req(fc)) |
| 1506 |
tx_flags |= TX_CMD_FLG_ACK_MSK | TX_CMD_FLG_IMM_BA_RSP_MASK; |
| 1507 |
|
| 1508 |
tx_cmd->sta_id = std_id; |
| 1509 |
if (ieee80211_has_morefrags(fc)) |
| 1510 |
tx_flags |= TX_CMD_FLG_MORE_FRAG_MSK; |
| 1511 |
|
| 1512 |
if (ieee80211_is_data_qos(fc)) { |
| 1513 |
u8 *qc = ieee80211_get_qos_ctl(hdr); |
| 1514 |
tx_cmd->tid_tspec = qc[0] & 0xf; |
| 1515 |
tx_flags &= ~TX_CMD_FLG_SEQ_CTL_MSK; |
| 1516 |
} else { |
| 1517 |
tx_flags |= TX_CMD_FLG_SEQ_CTL_MSK; |
| 1518 |
} |
| 1519 |
|
| 1520 |
il_tx_cmd_protection(il, info, fc, &tx_flags); |
| 1521 |
|
| 1522 |
tx_flags &= ~(TX_CMD_FLG_ANT_SEL_MSK); |
| 1523 |
if (ieee80211_is_mgmt(fc)) { |
| 1524 |
if (ieee80211_is_assoc_req(fc) || ieee80211_is_reassoc_req(fc)) |
| 1525 |
tx_cmd->timeout.pm_frame_timeout = cpu_to_le16(3); |
| 1526 |
else |
| 1527 |
tx_cmd->timeout.pm_frame_timeout = cpu_to_le16(2); |
| 1528 |
} else { |
| 1529 |
tx_cmd->timeout.pm_frame_timeout = 0; |
| 1530 |
} |
| 1531 |
|
| 1532 |
tx_cmd->driver_txop = 0; |
| 1533 |
tx_cmd->tx_flags = tx_flags; |
| 1534 |
tx_cmd->next_frame_len = 0; |
| 1535 |
} |
| 1536 |
|
| 1537 |
static void |
| 1538 |
il4965_tx_cmd_build_rate(struct il_priv *il, |
| 1539 |
struct il_tx_cmd *tx_cmd, |
| 1540 |
struct ieee80211_tx_info *info, |
| 1541 |
struct ieee80211_sta *sta, |
| 1542 |
__le16 fc) |
| 1543 |
{ |
| 1544 |
const u8 rts_retry_limit = 60; |
| 1545 |
u32 rate_flags; |
| 1546 |
int rate_idx; |
| 1547 |
u8 data_retry_limit; |
| 1548 |
u8 rate_plcp; |
| 1549 |
|
| 1550 |
/* Set retry limit on DATA packets and Probe Responses */ |
| 1551 |
if (ieee80211_is_probe_resp(fc)) |
| 1552 |
data_retry_limit = 3; |
| 1553 |
else |
| 1554 |
data_retry_limit = IL4965_DEFAULT_TX_RETRY; |
| 1555 |
tx_cmd->data_retry_limit = data_retry_limit; |
| 1556 |
/* Set retry limit on RTS packets */ |
| 1557 |
tx_cmd->rts_retry_limit = min(data_retry_limit, rts_retry_limit); |
| 1558 |
|
| 1559 |
/* DATA packets will use the uCode station table for rate/antenna |
| 1560 |
* selection */ |
| 1561 |
if (ieee80211_is_data(fc)) { |
| 1562 |
tx_cmd->initial_rate_idx = 0; |
| 1563 |
tx_cmd->tx_flags |= TX_CMD_FLG_STA_RATE_MSK; |
| 1564 |
return; |
| 1565 |
} |
| 1566 |
|
| 1567 |
/** |
| 1568 |
* If the current TX rate stored in mac80211 has the MCS bit set, it's |
| 1569 |
* not really a TX rate. Thus, we use the lowest supported rate for |
| 1570 |
* this band. Also use the lowest supported rate if the stored rate |
| 1571 |
* idx is invalid. |
| 1572 |
*/ |
| 1573 |
rate_idx = info->control.rates[0].idx; |
| 1574 |
if ((info->control.rates[0].flags & IEEE80211_TX_RC_MCS) || rate_idx < 0 |
| 1575 |
|| rate_idx > RATE_COUNT_LEGACY) |
| 1576 |
rate_idx = rate_lowest_index(&il->bands[info->band], sta); |
| 1577 |
/* For 5 GHZ band, remap mac80211 rate indices into driver indices */ |
| 1578 |
if (info->band == NL80211_BAND_5GHZ) { |
| 1579 |
rate_idx += IL_FIRST_OFDM_RATE; |
| 1580 |
if (rate_idx > IL_LAST_OFDM_RATE) |
| 1581 |
rate_idx = IL_LAST_OFDM_RATE; |
| 1582 |
} |
| 1583 |
/* Get PLCP rate for tx_cmd->rate_n_flags */ |
| 1584 |
rate_plcp = il_rates[rate_idx].plcp; |
| 1585 |
/* Zero out flags for this packet */ |
| 1586 |
rate_flags = 0; |
| 1587 |
|
| 1588 |
/* Set CCK flag as needed */ |
| 1589 |
if (rate_idx >= IL_FIRST_CCK_RATE && rate_idx <= IL_LAST_CCK_RATE) |
| 1590 |
rate_flags |= RATE_MCS_CCK_MSK; |
| 1591 |
|
| 1592 |
/* Set up antennas */ |
| 1593 |
il4965_toggle_tx_ant(il, &il->mgmt_tx_ant, il->hw_params.valid_tx_ant); |
| 1594 |
rate_flags |= BIT(il->mgmt_tx_ant) << RATE_MCS_ANT_POS; |
| 1595 |
|
| 1596 |
/* Set the rate in the TX cmd */ |
| 1597 |
tx_cmd->rate_n_flags = cpu_to_le32(rate_plcp | rate_flags); |
| 1598 |
} |
| 1599 |
|
| 1600 |
static void |
| 1601 |
il4965_tx_cmd_build_hwcrypto(struct il_priv *il, struct ieee80211_tx_info *info, |
| 1602 |
struct il_tx_cmd *tx_cmd, struct sk_buff *skb_frag, |
| 1603 |
int sta_id) |
| 1604 |
{ |
| 1605 |
struct ieee80211_key_conf *keyconf = info->control.hw_key; |
| 1606 |
|
| 1607 |
switch (keyconf->cipher) { |
| 1608 |
case WLAN_CIPHER_SUITE_CCMP: |
| 1609 |
tx_cmd->sec_ctl = TX_CMD_SEC_CCM; |
| 1610 |
memcpy(tx_cmd->key, keyconf->key, keyconf->keylen); |
| 1611 |
if (info->flags & IEEE80211_TX_CTL_AMPDU) |
| 1612 |
tx_cmd->tx_flags |= TX_CMD_FLG_AGG_CCMP_MSK; |
| 1613 |
D_TX("tx_cmd with AES hwcrypto\n"); |
| 1614 |
break; |
| 1615 |
|
| 1616 |
case WLAN_CIPHER_SUITE_TKIP: |
| 1617 |
tx_cmd->sec_ctl = TX_CMD_SEC_TKIP; |
| 1618 |
ieee80211_get_tkip_p2k(keyconf, skb_frag, tx_cmd->key); |
| 1619 |
D_TX("tx_cmd with tkip hwcrypto\n"); |
| 1620 |
break; |
| 1621 |
|
| 1622 |
case WLAN_CIPHER_SUITE_WEP104: |
| 1623 |
tx_cmd->sec_ctl |= TX_CMD_SEC_KEY128; |
| 1624 |
fallthrough; |
| 1625 |
case WLAN_CIPHER_SUITE_WEP40: |
| 1626 |
tx_cmd->sec_ctl |= |
| 1627 |
(TX_CMD_SEC_WEP | (keyconf->keyidx & TX_CMD_SEC_MSK) << |
| 1628 |
TX_CMD_SEC_SHIFT); |
| 1629 |
|
| 1630 |
memcpy(&tx_cmd->key[3], keyconf->key, keyconf->keylen); |
| 1631 |
|
| 1632 |
D_TX("Configuring packet for WEP encryption " "with key %d\n", |
| 1633 |
keyconf->keyidx); |
| 1634 |
break; |
| 1635 |
|
| 1636 |
default: |
| 1637 |
IL_ERR("Unknown encode cipher %x\n", keyconf->cipher); |
| 1638 |
break; |
| 1639 |
} |
| 1640 |
} |
| 1641 |
|
| 1642 |
/* |
| 1643 |
* start C_TX command process |
| 1644 |
*/ |
| 1645 |
int |
| 1646 |
il4965_tx_skb(struct il_priv *il, |
| 1647 |
struct ieee80211_sta *sta, |
| 1648 |
struct sk_buff *skb) |
| 1649 |
{ |
| 1650 |
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; |
| 1651 |
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| 1652 |
struct il_station_priv *sta_priv = NULL; |
| 1653 |
struct il_tx_queue *txq; |
| 1654 |
struct il_queue *q; |
| 1655 |
struct il_device_cmd *out_cmd; |
| 1656 |
struct il_cmd_meta *out_meta; |
| 1657 |
struct il_tx_cmd *tx_cmd; |
| 1658 |
int txq_id; |
| 1659 |
dma_addr_t phys_addr; |
| 1660 |
dma_addr_t txcmd_phys; |
| 1661 |
dma_addr_t scratch_phys; |
| 1662 |
u16 len, firstlen, secondlen; |
| 1663 |
u16 seq_number = 0; |
| 1664 |
__le16 fc; |
| 1665 |
u8 hdr_len; |
| 1666 |
u8 sta_id; |
| 1667 |
u8 wait_write_ptr = 0; |
| 1668 |
u8 tid = 0; |
| 1669 |
u8 *qc = NULL; |
| 1670 |
unsigned long flags; |
| 1671 |
bool is_agg = false; |
| 1672 |
|
| 1673 |
spin_lock_irqsave(&il->lock, flags); |
| 1674 |
if (il_is_rfkill(il)) { |
| 1675 |
D_DROP("Dropping - RF KILL\n"); |
| 1676 |
goto drop_unlock; |
| 1677 |
} |
| 1678 |
|
| 1679 |
fc = hdr->frame_control; |
| 1680 |
|
| 1681 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 1682 |
if (ieee80211_is_auth(fc)) |
| 1683 |
D_TX("Sending AUTH frame\n"); |
| 1684 |
else if (ieee80211_is_assoc_req(fc)) |
| 1685 |
D_TX("Sending ASSOC frame\n"); |
| 1686 |
else if (ieee80211_is_reassoc_req(fc)) |
| 1687 |
D_TX("Sending REASSOC frame\n"); |
| 1688 |
#endif |
| 1689 |
|
| 1690 |
hdr_len = ieee80211_hdrlen(fc); |
| 1691 |
|
| 1692 |
/* For management frames use broadcast id to do not break aggregation */ |
| 1693 |
if (!ieee80211_is_data(fc)) |
| 1694 |
sta_id = il->hw_params.bcast_id; |
| 1695 |
else { |
| 1696 |
/* Find idx into station table for destination station */ |
| 1697 |
sta_id = il_sta_id_or_broadcast(il, sta); |
| 1698 |
|
| 1699 |
if (sta_id == IL_INVALID_STATION) { |
| 1700 |
D_DROP("Dropping - INVALID STATION: %pM\n", hdr->addr1); |
| 1701 |
goto drop_unlock; |
| 1702 |
} |
| 1703 |
} |
| 1704 |
|
| 1705 |
D_TX("station Id %d\n", sta_id); |
| 1706 |
|
| 1707 |
if (sta) |
| 1708 |
sta_priv = (void *)sta->drv_priv; |
| 1709 |
|
| 1710 |
if (sta_priv && sta_priv->asleep && |
| 1711 |
(info->flags & IEEE80211_TX_CTL_NO_PS_BUFFER)) { |
| 1712 |
/* |
| 1713 |
* This sends an asynchronous command to the device, |
| 1714 |
* but we can rely on it being processed before the |
| 1715 |
* next frame is processed -- and the next frame to |
| 1716 |
* this station is the one that will consume this |
| 1717 |
* counter. |
| 1718 |
* For now set the counter to just 1 since we do not |
| 1719 |
* support uAPSD yet. |
| 1720 |
*/ |
| 1721 |
il4965_sta_modify_sleep_tx_count(il, sta_id, 1); |
| 1722 |
} |
| 1723 |
|
| 1724 |
/* FIXME: remove me ? */ |
| 1725 |
WARN_ON_ONCE(info->flags & IEEE80211_TX_CTL_SEND_AFTER_DTIM); |
| 1726 |
|
| 1727 |
/* Access category (AC) is also the queue number */ |
| 1728 |
txq_id = skb_get_queue_mapping(skb); |
| 1729 |
|
| 1730 |
/* irqs already disabled/saved above when locking il->lock */ |
| 1731 |
spin_lock(&il->sta_lock); |
| 1732 |
|
| 1733 |
if (ieee80211_is_data_qos(fc)) { |
| 1734 |
qc = ieee80211_get_qos_ctl(hdr); |
| 1735 |
tid = qc[0] & IEEE80211_QOS_CTL_TID_MASK; |
| 1736 |
if (WARN_ON_ONCE(tid >= MAX_TID_COUNT)) { |
| 1737 |
spin_unlock(&il->sta_lock); |
| 1738 |
goto drop_unlock; |
| 1739 |
} |
| 1740 |
seq_number = il->stations[sta_id].tid[tid].seq_number; |
| 1741 |
seq_number &= IEEE80211_SCTL_SEQ; |
| 1742 |
hdr->seq_ctrl = |
| 1743 |
hdr->seq_ctrl & cpu_to_le16(IEEE80211_SCTL_FRAG); |
| 1744 |
hdr->seq_ctrl |= cpu_to_le16(seq_number); |
| 1745 |
seq_number += 0x10; |
| 1746 |
/* aggregation is on for this <sta,tid> */ |
| 1747 |
if (info->flags & IEEE80211_TX_CTL_AMPDU && |
| 1748 |
il->stations[sta_id].tid[tid].agg.state == IL_AGG_ON) { |
| 1749 |
txq_id = il->stations[sta_id].tid[tid].agg.txq_id; |
| 1750 |
is_agg = true; |
| 1751 |
} |
| 1752 |
} |
| 1753 |
|
| 1754 |
txq = &il->txq[txq_id]; |
| 1755 |
q = &txq->q; |
| 1756 |
|
| 1757 |
if (unlikely(il_queue_space(q) < q->high_mark)) { |
| 1758 |
spin_unlock(&il->sta_lock); |
| 1759 |
goto drop_unlock; |
| 1760 |
} |
| 1761 |
|
| 1762 |
if (ieee80211_is_data_qos(fc)) { |
| 1763 |
il->stations[sta_id].tid[tid].tfds_in_queue++; |
| 1764 |
if (!ieee80211_has_morefrags(fc)) |
| 1765 |
il->stations[sta_id].tid[tid].seq_number = seq_number; |
| 1766 |
} |
| 1767 |
|
| 1768 |
spin_unlock(&il->sta_lock); |
| 1769 |
|
| 1770 |
txq->skbs[q->write_ptr] = skb; |
| 1771 |
|
| 1772 |
/* Set up first empty entry in queue's array of Tx/cmd buffers */ |
| 1773 |
out_cmd = txq->cmd[q->write_ptr]; |
| 1774 |
out_meta = &txq->meta[q->write_ptr]; |
| 1775 |
tx_cmd = container_of(&out_cmd->cmd.tx, struct il_tx_cmd, __hdr); |
| 1776 |
memset(&out_cmd->hdr, 0, sizeof(out_cmd->hdr)); |
| 1777 |
memset(tx_cmd, 0, sizeof(struct il_tx_cmd)); |
| 1778 |
|
| 1779 |
/* |
| 1780 |
* Set up the Tx-command (not MAC!) header. |
| 1781 |
* Store the chosen Tx queue and TFD idx within the sequence field; |
| 1782 |
* after Tx, uCode's Tx response will return this value so driver can |
| 1783 |
* locate the frame within the tx queue and do post-tx processing. |
| 1784 |
*/ |
| 1785 |
out_cmd->hdr.cmd = C_TX; |
| 1786 |
out_cmd->hdr.sequence = |
| 1787 |
cpu_to_le16((u16) |
| 1788 |
(QUEUE_TO_SEQ(txq_id) | IDX_TO_SEQ(q->write_ptr))); |
| 1789 |
|
| 1790 |
/* Copy MAC header from skb into command buffer */ |
| 1791 |
memcpy(tx_cmd->hdr, hdr, hdr_len); |
| 1792 |
|
| 1793 |
/* Total # bytes to be transmitted */ |
| 1794 |
tx_cmd->len = cpu_to_le16((u16) skb->len); |
| 1795 |
|
| 1796 |
if (info->control.hw_key) |
| 1797 |
il4965_tx_cmd_build_hwcrypto(il, info, tx_cmd, skb, sta_id); |
| 1798 |
|
| 1799 |
/* TODO need this for burst mode later on */ |
| 1800 |
il4965_tx_cmd_build_basic(il, skb, tx_cmd, info, hdr, sta_id); |
| 1801 |
|
| 1802 |
il4965_tx_cmd_build_rate(il, tx_cmd, info, sta, fc); |
| 1803 |
|
| 1804 |
/* |
| 1805 |
* Use the first empty entry in this queue's command buffer array |
| 1806 |
* to contain the Tx command and MAC header concatenated together |
| 1807 |
* (payload data will be in another buffer). |
| 1808 |
* Size of this varies, due to varying MAC header length. |
| 1809 |
* If end is not dword aligned, we'll have 2 extra bytes at the end |
| 1810 |
* of the MAC header (device reads on dword boundaries). |
| 1811 |
* We'll tell device about this padding later. |
| 1812 |
*/ |
| 1813 |
len = sizeof(struct il_tx_cmd) + sizeof(struct il_cmd_header) + hdr_len; |
| 1814 |
firstlen = (len + 3) & ~3; |
| 1815 |
|
| 1816 |
/* Tell NIC about any 2-byte padding after MAC header */ |
| 1817 |
if (firstlen != len) |
| 1818 |
tx_cmd->tx_flags |= TX_CMD_FLG_MH_PAD_MSK; |
| 1819 |
|
| 1820 |
/* Physical address of this Tx command's header (not MAC header!), |
| 1821 |
* within command buffer array. */ |
| 1822 |
txcmd_phys = dma_map_single(&il->pci_dev->dev, &out_cmd->hdr, firstlen, |
| 1823 |
DMA_BIDIRECTIONAL); |
| 1824 |
if (unlikely(dma_mapping_error(&il->pci_dev->dev, txcmd_phys))) |
| 1825 |
goto drop_unlock; |
| 1826 |
|
| 1827 |
/* Set up TFD's 2nd entry to point directly to remainder of skb, |
| 1828 |
* if any (802.11 null frames have no payload). */ |
| 1829 |
secondlen = skb->len - hdr_len; |
| 1830 |
if (secondlen > 0) { |
| 1831 |
phys_addr = dma_map_single(&il->pci_dev->dev, skb->data + hdr_len, |
| 1832 |
secondlen, DMA_TO_DEVICE); |
| 1833 |
if (unlikely(dma_mapping_error(&il->pci_dev->dev, phys_addr))) |
| 1834 |
goto drop_unlock; |
| 1835 |
} |
| 1836 |
|
| 1837 |
/* Add buffer containing Tx command and MAC(!) header to TFD's |
| 1838 |
* first entry */ |
| 1839 |
il->ops->txq_attach_buf_to_tfd(il, txq, txcmd_phys, firstlen, 1, 0); |
| 1840 |
dma_unmap_addr_set(out_meta, mapping, txcmd_phys); |
| 1841 |
dma_unmap_len_set(out_meta, len, firstlen); |
| 1842 |
if (secondlen) |
| 1843 |
il->ops->txq_attach_buf_to_tfd(il, txq, phys_addr, secondlen, |
| 1844 |
0, 0); |
| 1845 |
|
| 1846 |
if (!ieee80211_has_morefrags(hdr->frame_control)) { |
| 1847 |
txq->need_update = 1; |
| 1848 |
} else { |
| 1849 |
wait_write_ptr = 1; |
| 1850 |
txq->need_update = 0; |
| 1851 |
} |
| 1852 |
|
| 1853 |
scratch_phys = |
| 1854 |
txcmd_phys + sizeof(struct il_cmd_header) + |
| 1855 |
offsetof(struct il_tx_cmd, scratch); |
| 1856 |
|
| 1857 |
/* take back ownership of DMA buffer to enable update */ |
| 1858 |
dma_sync_single_for_cpu(&il->pci_dev->dev, txcmd_phys, firstlen, |
| 1859 |
DMA_BIDIRECTIONAL); |
| 1860 |
tx_cmd->dram_lsb_ptr = cpu_to_le32(scratch_phys); |
| 1861 |
tx_cmd->dram_msb_ptr = il_get_dma_hi_addr(scratch_phys); |
| 1862 |
|
| 1863 |
il_update_stats(il, true, fc, skb->len); |
| 1864 |
|
| 1865 |
D_TX("sequence nr = 0X%x\n", le16_to_cpu(out_cmd->hdr.sequence)); |
| 1866 |
D_TX("tx_flags = 0X%x\n", le32_to_cpu(tx_cmd->tx_flags)); |
| 1867 |
il_print_hex_dump(il, IL_DL_TX, (u8 *) tx_cmd, sizeof(*tx_cmd)); |
| 1868 |
il_print_hex_dump(il, IL_DL_TX, (u8 *) tx_cmd->hdr, hdr_len); |
| 1869 |
|
| 1870 |
/* Set up entry for this TFD in Tx byte-count array */ |
| 1871 |
if (info->flags & IEEE80211_TX_CTL_AMPDU) |
| 1872 |
il->ops->txq_update_byte_cnt_tbl(il, txq, le16_to_cpu(tx_cmd->len)); |
| 1873 |
|
| 1874 |
dma_sync_single_for_device(&il->pci_dev->dev, txcmd_phys, firstlen, |
| 1875 |
DMA_BIDIRECTIONAL); |
| 1876 |
|
| 1877 |
/* Tell device the write idx *just past* this latest filled TFD */ |
| 1878 |
q->write_ptr = il_queue_inc_wrap(q->write_ptr, q->n_bd); |
| 1879 |
il_txq_update_write_ptr(il, txq); |
| 1880 |
spin_unlock_irqrestore(&il->lock, flags); |
| 1881 |
|
| 1882 |
/* |
| 1883 |
* At this point the frame is "transmitted" successfully |
| 1884 |
* and we will get a TX status notification eventually, |
| 1885 |
* regardless of the value of ret. "ret" only indicates |
| 1886 |
* whether or not we should update the write pointer. |
| 1887 |
*/ |
| 1888 |
|
| 1889 |
/* |
| 1890 |
* Avoid atomic ops if it isn't an associated client. |
| 1891 |
* Also, if this is a packet for aggregation, don't |
| 1892 |
* increase the counter because the ucode will stop |
| 1893 |
* aggregation queues when their respective station |
| 1894 |
* goes to sleep. |
| 1895 |
*/ |
| 1896 |
if (sta_priv && sta_priv->client && !is_agg) |
| 1897 |
atomic_inc(&sta_priv->pending_frames); |
| 1898 |
|
| 1899 |
if (il_queue_space(q) < q->high_mark && il->mac80211_registered) { |
| 1900 |
if (wait_write_ptr) { |
| 1901 |
spin_lock_irqsave(&il->lock, flags); |
| 1902 |
txq->need_update = 1; |
| 1903 |
il_txq_update_write_ptr(il, txq); |
| 1904 |
spin_unlock_irqrestore(&il->lock, flags); |
| 1905 |
} else { |
| 1906 |
il_stop_queue(il, txq); |
| 1907 |
} |
| 1908 |
} |
| 1909 |
|
| 1910 |
return 0; |
| 1911 |
|
| 1912 |
drop_unlock: |
| 1913 |
spin_unlock_irqrestore(&il->lock, flags); |
| 1914 |
return -1; |
| 1915 |
} |
| 1916 |
|
| 1917 |
static inline int |
| 1918 |
il4965_alloc_dma_ptr(struct il_priv *il, struct il_dma_ptr *ptr, size_t size) |
| 1919 |
{ |
| 1920 |
ptr->addr = dma_alloc_coherent(&il->pci_dev->dev, size, &ptr->dma, |
| 1921 |
GFP_KERNEL); |
| 1922 |
if (!ptr->addr) |
| 1923 |
return -ENOMEM; |
| 1924 |
ptr->size = size; |
| 1925 |
return 0; |
| 1926 |
} |
| 1927 |
|
| 1928 |
static inline void |
| 1929 |
il4965_free_dma_ptr(struct il_priv *il, struct il_dma_ptr *ptr) |
| 1930 |
{ |
| 1931 |
if (unlikely(!ptr->addr)) |
| 1932 |
return; |
| 1933 |
|
| 1934 |
dma_free_coherent(&il->pci_dev->dev, ptr->size, ptr->addr, ptr->dma); |
| 1935 |
memset(ptr, 0, sizeof(*ptr)); |
| 1936 |
} |
| 1937 |
|
| 1938 |
/* |
| 1939 |
* il4965_hw_txq_ctx_free - Free TXQ Context |
| 1940 |
* |
| 1941 |
* Destroy all TX DMA queues and structures |
| 1942 |
*/ |
| 1943 |
void |
| 1944 |
il4965_hw_txq_ctx_free(struct il_priv *il) |
| 1945 |
{ |
| 1946 |
int txq_id; |
| 1947 |
|
| 1948 |
/* Tx queues */ |
| 1949 |
if (il->txq) { |
| 1950 |
for (txq_id = 0; txq_id < il->hw_params.max_txq_num; txq_id++) |
| 1951 |
if (txq_id == il->cmd_queue) |
| 1952 |
il_cmd_queue_free(il); |
| 1953 |
else |
| 1954 |
il_tx_queue_free(il, txq_id); |
| 1955 |
} |
| 1956 |
il4965_free_dma_ptr(il, &il->kw); |
| 1957 |
|
| 1958 |
il4965_free_dma_ptr(il, &il->scd_bc_tbls); |
| 1959 |
|
| 1960 |
/* free tx queue structure */ |
| 1961 |
il_free_txq_mem(il); |
| 1962 |
} |
| 1963 |
|
| 1964 |
/* |
| 1965 |
* il4965_txq_ctx_alloc - allocate TX queue context |
| 1966 |
* Allocate all Tx DMA structures and initialize them |
| 1967 |
*/ |
| 1968 |
int |
| 1969 |
il4965_txq_ctx_alloc(struct il_priv *il) |
| 1970 |
{ |
| 1971 |
int ret, txq_id; |
| 1972 |
unsigned long flags; |
| 1973 |
|
| 1974 |
/* Free all tx/cmd queues and keep-warm buffer */ |
| 1975 |
il4965_hw_txq_ctx_free(il); |
| 1976 |
|
| 1977 |
ret = |
| 1978 |
il4965_alloc_dma_ptr(il, &il->scd_bc_tbls, |
| 1979 |
il->hw_params.scd_bc_tbls_size); |
| 1980 |
if (ret) { |
| 1981 |
IL_ERR("Scheduler BC Table allocation failed\n"); |
| 1982 |
goto error_bc_tbls; |
| 1983 |
} |
| 1984 |
/* Alloc keep-warm buffer */ |
| 1985 |
ret = il4965_alloc_dma_ptr(il, &il->kw, IL_KW_SIZE); |
| 1986 |
if (ret) { |
| 1987 |
IL_ERR("Keep Warm allocation failed\n"); |
| 1988 |
goto error_kw; |
| 1989 |
} |
| 1990 |
|
| 1991 |
/* allocate tx queue structure */ |
| 1992 |
ret = il_alloc_txq_mem(il); |
| 1993 |
if (ret) |
| 1994 |
goto error; |
| 1995 |
|
| 1996 |
spin_lock_irqsave(&il->lock, flags); |
| 1997 |
|
| 1998 |
/* Turn off all Tx DMA fifos */ |
| 1999 |
il4965_txq_set_sched(il, 0); |
| 2000 |
|
| 2001 |
/* Tell NIC where to find the "keep warm" buffer */ |
| 2002 |
il_wr(il, FH49_KW_MEM_ADDR_REG, il->kw.dma >> 4); |
| 2003 |
|
| 2004 |
spin_unlock_irqrestore(&il->lock, flags); |
| 2005 |
|
| 2006 |
/* Alloc and init all Tx queues, including the command queue (#4/#9) */ |
| 2007 |
for (txq_id = 0; txq_id < il->hw_params.max_txq_num; txq_id++) { |
| 2008 |
ret = il_tx_queue_init(il, txq_id); |
| 2009 |
if (ret) { |
| 2010 |
IL_ERR("Tx %d queue init failed\n", txq_id); |
| 2011 |
goto error; |
| 2012 |
} |
| 2013 |
} |
| 2014 |
|
| 2015 |
return ret; |
| 2016 |
|
| 2017 |
error: |
| 2018 |
il4965_hw_txq_ctx_free(il); |
| 2019 |
il4965_free_dma_ptr(il, &il->kw); |
| 2020 |
error_kw: |
| 2021 |
il4965_free_dma_ptr(il, &il->scd_bc_tbls); |
| 2022 |
error_bc_tbls: |
| 2023 |
return ret; |
| 2024 |
} |
| 2025 |
|
| 2026 |
void |
| 2027 |
il4965_txq_ctx_reset(struct il_priv *il) |
| 2028 |
{ |
| 2029 |
int txq_id; |
| 2030 |
unsigned long flags; |
| 2031 |
|
| 2032 |
spin_lock_irqsave(&il->lock, flags); |
| 2033 |
|
| 2034 |
/* Turn off all Tx DMA fifos */ |
| 2035 |
il4965_txq_set_sched(il, 0); |
| 2036 |
/* Tell NIC where to find the "keep warm" buffer */ |
| 2037 |
il_wr(il, FH49_KW_MEM_ADDR_REG, il->kw.dma >> 4); |
| 2038 |
|
| 2039 |
spin_unlock_irqrestore(&il->lock, flags); |
| 2040 |
|
| 2041 |
/* Alloc and init all Tx queues, including the command queue (#4) */ |
| 2042 |
for (txq_id = 0; txq_id < il->hw_params.max_txq_num; txq_id++) |
| 2043 |
il_tx_queue_reset(il, txq_id); |
| 2044 |
} |
| 2045 |
|
| 2046 |
static void |
| 2047 |
il4965_txq_ctx_unmap(struct il_priv *il) |
| 2048 |
{ |
| 2049 |
int txq_id; |
| 2050 |
|
| 2051 |
if (!il->txq) |
| 2052 |
return; |
| 2053 |
|
| 2054 |
/* Unmap DMA from host system and free skb's */ |
| 2055 |
for (txq_id = 0; txq_id < il->hw_params.max_txq_num; txq_id++) |
| 2056 |
if (txq_id == il->cmd_queue) |
| 2057 |
il_cmd_queue_unmap(il); |
| 2058 |
else |
| 2059 |
il_tx_queue_unmap(il, txq_id); |
| 2060 |
} |
| 2061 |
|
| 2062 |
/* |
| 2063 |
* il4965_txq_ctx_stop - Stop all Tx DMA channels |
| 2064 |
*/ |
| 2065 |
void |
| 2066 |
il4965_txq_ctx_stop(struct il_priv *il) |
| 2067 |
{ |
| 2068 |
int ch, ret; |
| 2069 |
|
| 2070 |
_il_wr_prph(il, IL49_SCD_TXFACT, 0); |
| 2071 |
|
| 2072 |
/* Stop each Tx DMA channel, and wait for it to be idle */ |
| 2073 |
for (ch = 0; ch < il->hw_params.dma_chnl_num; ch++) { |
| 2074 |
_il_wr(il, FH49_TCSR_CHNL_TX_CONFIG_REG(ch), 0x0); |
| 2075 |
ret = |
| 2076 |
_il_poll_bit(il, FH49_TSSR_TX_STATUS_REG, |
| 2077 |
FH49_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(ch), |
| 2078 |
FH49_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(ch), |
| 2079 |
1000); |
| 2080 |
if (ret < 0) |
| 2081 |
IL_ERR("Timeout stopping DMA channel %d [0x%08x]", |
| 2082 |
ch, _il_rd(il, FH49_TSSR_TX_STATUS_REG)); |
| 2083 |
} |
| 2084 |
} |
| 2085 |
|
| 2086 |
/* |
| 2087 |
* Find first available (lowest unused) Tx Queue, mark it "active". |
| 2088 |
* Called only when finding queue for aggregation. |
| 2089 |
* Should never return anything < 7, because they should already |
| 2090 |
* be in use as EDCA AC (0-3), Command (4), reserved (5, 6) |
| 2091 |
*/ |
| 2092 |
static int |
| 2093 |
il4965_txq_ctx_activate_free(struct il_priv *il) |
| 2094 |
{ |
| 2095 |
int txq_id; |
| 2096 |
|
| 2097 |
for (txq_id = 0; txq_id < il->hw_params.max_txq_num; txq_id++) |
| 2098 |
if (!test_and_set_bit(txq_id, &il->txq_ctx_active_msk)) |
| 2099 |
return txq_id; |
| 2100 |
return -1; |
| 2101 |
} |
| 2102 |
|
| 2103 |
/* |
| 2104 |
* il4965_tx_queue_stop_scheduler - Stop queue, but keep configuration |
| 2105 |
*/ |
| 2106 |
static void |
| 2107 |
il4965_tx_queue_stop_scheduler(struct il_priv *il, u16 txq_id) |
| 2108 |
{ |
| 2109 |
/* Simply stop the queue, but don't change any configuration; |
| 2110 |
* the SCD_ACT_EN bit is the write-enable mask for the ACTIVE bit. */ |
| 2111 |
il_wr_prph(il, IL49_SCD_QUEUE_STATUS_BITS(txq_id), |
| 2112 |
(0 << IL49_SCD_QUEUE_STTS_REG_POS_ACTIVE) | |
| 2113 |
(1 << IL49_SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN)); |
| 2114 |
} |
| 2115 |
|
| 2116 |
/* |
| 2117 |
* il4965_tx_queue_set_q2ratid - Map unique receiver/tid combination to a queue |
| 2118 |
*/ |
| 2119 |
static int |
| 2120 |
il4965_tx_queue_set_q2ratid(struct il_priv *il, u16 ra_tid, u16 txq_id) |
| 2121 |
{ |
| 2122 |
u32 tbl_dw_addr; |
| 2123 |
u32 tbl_dw; |
| 2124 |
u16 scd_q2ratid; |
| 2125 |
|
| 2126 |
scd_q2ratid = ra_tid & IL_SCD_QUEUE_RA_TID_MAP_RATID_MSK; |
| 2127 |
|
| 2128 |
tbl_dw_addr = |
| 2129 |
il->scd_base_addr + IL49_SCD_TRANSLATE_TBL_OFFSET_QUEUE(txq_id); |
| 2130 |
|
| 2131 |
tbl_dw = il_read_targ_mem(il, tbl_dw_addr); |
| 2132 |
|
| 2133 |
if (txq_id & 0x1) |
| 2134 |
tbl_dw = (scd_q2ratid << 16) | (tbl_dw & 0x0000FFFF); |
| 2135 |
else |
| 2136 |
tbl_dw = scd_q2ratid | (tbl_dw & 0xFFFF0000); |
| 2137 |
|
| 2138 |
il_write_targ_mem(il, tbl_dw_addr, tbl_dw); |
| 2139 |
|
| 2140 |
return 0; |
| 2141 |
} |
| 2142 |
|
| 2143 |
/* |
| 2144 |
* il4965_tx_queue_agg_enable - Set up & enable aggregation for selected queue |
| 2145 |
* |
| 2146 |
* NOTE: txq_id must be greater than IL49_FIRST_AMPDU_QUEUE, |
| 2147 |
* i.e. it must be one of the higher queues used for aggregation |
| 2148 |
*/ |
| 2149 |
static int |
| 2150 |
il4965_txq_agg_enable(struct il_priv *il, int txq_id, int tx_fifo, int sta_id, |
| 2151 |
int tid, u16 ssn_idx) |
| 2152 |
{ |
| 2153 |
unsigned long flags; |
| 2154 |
u16 ra_tid; |
| 2155 |
int ret; |
| 2156 |
|
| 2157 |
if ((IL49_FIRST_AMPDU_QUEUE > txq_id) || |
| 2158 |
(IL49_FIRST_AMPDU_QUEUE + |
| 2159 |
il->cfg->num_of_ampdu_queues <= txq_id)) { |
| 2160 |
IL_WARN("queue number out of range: %d, must be %d to %d\n", |
| 2161 |
txq_id, IL49_FIRST_AMPDU_QUEUE, |
| 2162 |
IL49_FIRST_AMPDU_QUEUE + |
| 2163 |
il->cfg->num_of_ampdu_queues - 1); |
| 2164 |
return -EINVAL; |
| 2165 |
} |
| 2166 |
|
| 2167 |
ra_tid = BUILD_RAxTID(sta_id, tid); |
| 2168 |
|
| 2169 |
/* Modify device's station table to Tx this TID */ |
| 2170 |
ret = il4965_sta_tx_modify_enable_tid(il, sta_id, tid); |
| 2171 |
if (ret) |
| 2172 |
return ret; |
| 2173 |
|
| 2174 |
spin_lock_irqsave(&il->lock, flags); |
| 2175 |
|
| 2176 |
/* Stop this Tx queue before configuring it */ |
| 2177 |
il4965_tx_queue_stop_scheduler(il, txq_id); |
| 2178 |
|
| 2179 |
/* Map receiver-address / traffic-ID to this queue */ |
| 2180 |
il4965_tx_queue_set_q2ratid(il, ra_tid, txq_id); |
| 2181 |
|
| 2182 |
/* Set this queue as a chain-building queue */ |
| 2183 |
il_set_bits_prph(il, IL49_SCD_QUEUECHAIN_SEL, (1 << txq_id)); |
| 2184 |
|
| 2185 |
/* Place first TFD at idx corresponding to start sequence number. |
| 2186 |
* Assumes that ssn_idx is valid (!= 0xFFF) */ |
| 2187 |
il->txq[txq_id].q.read_ptr = (ssn_idx & 0xff); |
| 2188 |
il->txq[txq_id].q.write_ptr = (ssn_idx & 0xff); |
| 2189 |
il4965_set_wr_ptrs(il, txq_id, ssn_idx); |
| 2190 |
|
| 2191 |
/* Set up Tx win size and frame limit for this queue */ |
| 2192 |
il_write_targ_mem(il, |
| 2193 |
il->scd_base_addr + |
| 2194 |
IL49_SCD_CONTEXT_QUEUE_OFFSET(txq_id), |
| 2195 |
(SCD_WIN_SIZE << IL49_SCD_QUEUE_CTX_REG1_WIN_SIZE_POS) |
| 2196 |
& IL49_SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK); |
| 2197 |
|
| 2198 |
il_write_targ_mem(il, |
| 2199 |
il->scd_base_addr + |
| 2200 |
IL49_SCD_CONTEXT_QUEUE_OFFSET(txq_id) + sizeof(u32), |
| 2201 |
(SCD_FRAME_LIMIT << |
| 2202 |
IL49_SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS) & |
| 2203 |
IL49_SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK); |
| 2204 |
|
| 2205 |
il_set_bits_prph(il, IL49_SCD_INTERRUPT_MASK, (1 << txq_id)); |
| 2206 |
|
| 2207 |
/* Set up Status area in SRAM, map to Tx DMA/FIFO, activate the queue */ |
| 2208 |
il4965_tx_queue_set_status(il, &il->txq[txq_id], tx_fifo, 1); |
| 2209 |
|
| 2210 |
spin_unlock_irqrestore(&il->lock, flags); |
| 2211 |
|
| 2212 |
return 0; |
| 2213 |
} |
| 2214 |
|
| 2215 |
int |
| 2216 |
il4965_tx_agg_start(struct il_priv *il, struct ieee80211_vif *vif, |
| 2217 |
struct ieee80211_sta *sta, u16 tid, u16 * ssn) |
| 2218 |
{ |
| 2219 |
int sta_id; |
| 2220 |
int tx_fifo; |
| 2221 |
int txq_id; |
| 2222 |
int ret; |
| 2223 |
unsigned long flags; |
| 2224 |
struct il_tid_data *tid_data; |
| 2225 |
|
| 2226 |
/* FIXME: warning if tx fifo not found ? */ |
| 2227 |
tx_fifo = il4965_get_fifo_from_tid(tid); |
| 2228 |
if (unlikely(tx_fifo < 0)) |
| 2229 |
return tx_fifo; |
| 2230 |
|
| 2231 |
D_HT("%s on ra = %pM tid = %d\n", __func__, sta->addr, tid); |
| 2232 |
|
| 2233 |
sta_id = il_sta_id(sta); |
| 2234 |
if (sta_id == IL_INVALID_STATION) { |
| 2235 |
IL_ERR("Start AGG on invalid station\n"); |
| 2236 |
return -ENXIO; |
| 2237 |
} |
| 2238 |
if (unlikely(tid >= MAX_TID_COUNT)) |
| 2239 |
return -EINVAL; |
| 2240 |
|
| 2241 |
if (il->stations[sta_id].tid[tid].agg.state != IL_AGG_OFF) { |
| 2242 |
IL_ERR("Start AGG when state is not IL_AGG_OFF !\n"); |
| 2243 |
return -ENXIO; |
| 2244 |
} |
| 2245 |
|
| 2246 |
txq_id = il4965_txq_ctx_activate_free(il); |
| 2247 |
if (txq_id == -1) { |
| 2248 |
IL_ERR("No free aggregation queue available\n"); |
| 2249 |
return -ENXIO; |
| 2250 |
} |
| 2251 |
|
| 2252 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 2253 |
tid_data = &il->stations[sta_id].tid[tid]; |
| 2254 |
*ssn = IEEE80211_SEQ_TO_SN(tid_data->seq_number); |
| 2255 |
tid_data->agg.txq_id = txq_id; |
| 2256 |
il_set_swq_id(&il->txq[txq_id], il4965_get_ac_from_tid(tid), txq_id); |
| 2257 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 2258 |
|
| 2259 |
ret = il4965_txq_agg_enable(il, txq_id, tx_fifo, sta_id, tid, *ssn); |
| 2260 |
if (ret) |
| 2261 |
return ret; |
| 2262 |
|
| 2263 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 2264 |
tid_data = &il->stations[sta_id].tid[tid]; |
| 2265 |
if (tid_data->tfds_in_queue == 0) { |
| 2266 |
D_HT("HW queue is empty\n"); |
| 2267 |
tid_data->agg.state = IL_AGG_ON; |
| 2268 |
ret = IEEE80211_AMPDU_TX_START_IMMEDIATE; |
| 2269 |
} else { |
| 2270 |
D_HT("HW queue is NOT empty: %d packets in HW queue\n", |
| 2271 |
tid_data->tfds_in_queue); |
| 2272 |
tid_data->agg.state = IL_EMPTYING_HW_QUEUE_ADDBA; |
| 2273 |
} |
| 2274 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 2275 |
return ret; |
| 2276 |
} |
| 2277 |
|
| 2278 |
/* |
| 2279 |
* txq_id must be greater than IL49_FIRST_AMPDU_QUEUE |
| 2280 |
* il->lock must be held by the caller |
| 2281 |
*/ |
| 2282 |
static int |
| 2283 |
il4965_txq_agg_disable(struct il_priv *il, u16 txq_id, u16 ssn_idx, u8 tx_fifo) |
| 2284 |
{ |
| 2285 |
if ((IL49_FIRST_AMPDU_QUEUE > txq_id) || |
| 2286 |
(IL49_FIRST_AMPDU_QUEUE + |
| 2287 |
il->cfg->num_of_ampdu_queues <= txq_id)) { |
| 2288 |
IL_WARN("queue number out of range: %d, must be %d to %d\n", |
| 2289 |
txq_id, IL49_FIRST_AMPDU_QUEUE, |
| 2290 |
IL49_FIRST_AMPDU_QUEUE + |
| 2291 |
il->cfg->num_of_ampdu_queues - 1); |
| 2292 |
return -EINVAL; |
| 2293 |
} |
| 2294 |
|
| 2295 |
il4965_tx_queue_stop_scheduler(il, txq_id); |
| 2296 |
|
| 2297 |
il_clear_bits_prph(il, IL49_SCD_QUEUECHAIN_SEL, (1 << txq_id)); |
| 2298 |
|
| 2299 |
il->txq[txq_id].q.read_ptr = (ssn_idx & 0xff); |
| 2300 |
il->txq[txq_id].q.write_ptr = (ssn_idx & 0xff); |
| 2301 |
/* supposes that ssn_idx is valid (!= 0xFFF) */ |
| 2302 |
il4965_set_wr_ptrs(il, txq_id, ssn_idx); |
| 2303 |
|
| 2304 |
il_clear_bits_prph(il, IL49_SCD_INTERRUPT_MASK, (1 << txq_id)); |
| 2305 |
il_txq_ctx_deactivate(il, txq_id); |
| 2306 |
il4965_tx_queue_set_status(il, &il->txq[txq_id], tx_fifo, 0); |
| 2307 |
|
| 2308 |
return 0; |
| 2309 |
} |
| 2310 |
|
| 2311 |
int |
| 2312 |
il4965_tx_agg_stop(struct il_priv *il, struct ieee80211_vif *vif, |
| 2313 |
struct ieee80211_sta *sta, u16 tid) |
| 2314 |
{ |
| 2315 |
int tx_fifo_id, txq_id, sta_id, ssn; |
| 2316 |
struct il_tid_data *tid_data; |
| 2317 |
int write_ptr, read_ptr; |
| 2318 |
unsigned long flags; |
| 2319 |
|
| 2320 |
/* FIXME: warning if tx_fifo_id not found ? */ |
| 2321 |
tx_fifo_id = il4965_get_fifo_from_tid(tid); |
| 2322 |
if (unlikely(tx_fifo_id < 0)) |
| 2323 |
return tx_fifo_id; |
| 2324 |
|
| 2325 |
sta_id = il_sta_id(sta); |
| 2326 |
|
| 2327 |
if (sta_id == IL_INVALID_STATION) { |
| 2328 |
IL_ERR("Invalid station for AGG tid %d\n", tid); |
| 2329 |
return -ENXIO; |
| 2330 |
} |
| 2331 |
|
| 2332 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 2333 |
|
| 2334 |
tid_data = &il->stations[sta_id].tid[tid]; |
| 2335 |
ssn = (tid_data->seq_number & IEEE80211_SCTL_SEQ) >> 4; |
| 2336 |
txq_id = tid_data->agg.txq_id; |
| 2337 |
|
| 2338 |
switch (il->stations[sta_id].tid[tid].agg.state) { |
| 2339 |
case IL_EMPTYING_HW_QUEUE_ADDBA: |
| 2340 |
/* |
| 2341 |
* This can happen if the peer stops aggregation |
| 2342 |
* again before we've had a chance to drain the |
| 2343 |
* queue we selected previously, i.e. before the |
| 2344 |
* session was really started completely. |
| 2345 |
*/ |
| 2346 |
D_HT("AGG stop before setup done\n"); |
| 2347 |
goto turn_off; |
| 2348 |
case IL_AGG_ON: |
| 2349 |
break; |
| 2350 |
default: |
| 2351 |
IL_WARN("Stopping AGG while state not ON or starting\n"); |
| 2352 |
} |
| 2353 |
|
| 2354 |
write_ptr = il->txq[txq_id].q.write_ptr; |
| 2355 |
read_ptr = il->txq[txq_id].q.read_ptr; |
| 2356 |
|
| 2357 |
/* The queue is not empty */ |
| 2358 |
if (write_ptr != read_ptr) { |
| 2359 |
D_HT("Stopping a non empty AGG HW QUEUE\n"); |
| 2360 |
il->stations[sta_id].tid[tid].agg.state = |
| 2361 |
IL_EMPTYING_HW_QUEUE_DELBA; |
| 2362 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 2363 |
return 0; |
| 2364 |
} |
| 2365 |
|
| 2366 |
D_HT("HW queue is empty\n"); |
| 2367 |
turn_off: |
| 2368 |
il->stations[sta_id].tid[tid].agg.state = IL_AGG_OFF; |
| 2369 |
|
| 2370 |
/* do not restore/save irqs */ |
| 2371 |
spin_unlock(&il->sta_lock); |
| 2372 |
spin_lock(&il->lock); |
| 2373 |
|
| 2374 |
/* |
| 2375 |
* the only reason this call can fail is queue number out of range, |
| 2376 |
* which can happen if uCode is reloaded and all the station |
| 2377 |
* information are lost. if it is outside the range, there is no need |
| 2378 |
* to deactivate the uCode queue, just return "success" to allow |
| 2379 |
* mac80211 to clean up it own data. |
| 2380 |
*/ |
| 2381 |
il4965_txq_agg_disable(il, txq_id, ssn, tx_fifo_id); |
| 2382 |
spin_unlock_irqrestore(&il->lock, flags); |
| 2383 |
|
| 2384 |
ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid); |
| 2385 |
|
| 2386 |
return 0; |
| 2387 |
} |
| 2388 |
|
| 2389 |
int |
| 2390 |
il4965_txq_check_empty(struct il_priv *il, int sta_id, u8 tid, int txq_id) |
| 2391 |
{ |
| 2392 |
struct il_queue *q = &il->txq[txq_id].q; |
| 2393 |
u8 *addr = il->stations[sta_id].sta.sta.addr; |
| 2394 |
struct il_tid_data *tid_data = &il->stations[sta_id].tid[tid]; |
| 2395 |
|
| 2396 |
lockdep_assert_held(&il->sta_lock); |
| 2397 |
|
| 2398 |
switch (il->stations[sta_id].tid[tid].agg.state) { |
| 2399 |
case IL_EMPTYING_HW_QUEUE_DELBA: |
| 2400 |
/* We are reclaiming the last packet of the */ |
| 2401 |
/* aggregated HW queue */ |
| 2402 |
if (txq_id == tid_data->agg.txq_id && |
| 2403 |
q->read_ptr == q->write_ptr) { |
| 2404 |
u16 ssn = IEEE80211_SEQ_TO_SN(tid_data->seq_number); |
| 2405 |
int tx_fifo = il4965_get_fifo_from_tid(tid); |
| 2406 |
D_HT("HW queue empty: continue DELBA flow\n"); |
| 2407 |
il4965_txq_agg_disable(il, txq_id, ssn, tx_fifo); |
| 2408 |
tid_data->agg.state = IL_AGG_OFF; |
| 2409 |
ieee80211_stop_tx_ba_cb_irqsafe(il->vif, addr, tid); |
| 2410 |
} |
| 2411 |
break; |
| 2412 |
case IL_EMPTYING_HW_QUEUE_ADDBA: |
| 2413 |
/* We are reclaiming the last packet of the queue */ |
| 2414 |
if (tid_data->tfds_in_queue == 0) { |
| 2415 |
D_HT("HW queue empty: continue ADDBA flow\n"); |
| 2416 |
tid_data->agg.state = IL_AGG_ON; |
| 2417 |
ieee80211_start_tx_ba_cb_irqsafe(il->vif, addr, tid); |
| 2418 |
} |
| 2419 |
break; |
| 2420 |
} |
| 2421 |
|
| 2422 |
return 0; |
| 2423 |
} |
| 2424 |
|
| 2425 |
static void |
| 2426 |
il4965_non_agg_tx_status(struct il_priv *il, const u8 *addr1) |
| 2427 |
{ |
| 2428 |
struct ieee80211_sta *sta; |
| 2429 |
struct il_station_priv *sta_priv; |
| 2430 |
|
| 2431 |
rcu_read_lock(); |
| 2432 |
sta = ieee80211_find_sta(il->vif, addr1); |
| 2433 |
if (sta) { |
| 2434 |
sta_priv = (void *)sta->drv_priv; |
| 2435 |
/* avoid atomic ops if this isn't a client */ |
| 2436 |
if (sta_priv->client && |
| 2437 |
atomic_dec_return(&sta_priv->pending_frames) == 0) |
| 2438 |
ieee80211_sta_block_awake(il->hw, sta, false); |
| 2439 |
} |
| 2440 |
rcu_read_unlock(); |
| 2441 |
} |
| 2442 |
|
| 2443 |
static void |
| 2444 |
il4965_tx_status(struct il_priv *il, struct sk_buff *skb, bool is_agg) |
| 2445 |
{ |
| 2446 |
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; |
| 2447 |
|
| 2448 |
if (!is_agg) |
| 2449 |
il4965_non_agg_tx_status(il, hdr->addr1); |
| 2450 |
|
| 2451 |
ieee80211_tx_status_irqsafe(il->hw, skb); |
| 2452 |
} |
| 2453 |
|
| 2454 |
int |
| 2455 |
il4965_tx_queue_reclaim(struct il_priv *il, int txq_id, int idx) |
| 2456 |
{ |
| 2457 |
struct il_tx_queue *txq = &il->txq[txq_id]; |
| 2458 |
struct il_queue *q = &txq->q; |
| 2459 |
int nfreed = 0; |
| 2460 |
struct ieee80211_hdr *hdr; |
| 2461 |
struct sk_buff *skb; |
| 2462 |
|
| 2463 |
if (idx >= q->n_bd || il_queue_used(q, idx) == 0) { |
| 2464 |
IL_ERR("Read idx for DMA queue txq id (%d), idx %d, " |
| 2465 |
"is out of range [0-%d] %d %d.\n", txq_id, idx, q->n_bd, |
| 2466 |
q->write_ptr, q->read_ptr); |
| 2467 |
return 0; |
| 2468 |
} |
| 2469 |
|
| 2470 |
for (idx = il_queue_inc_wrap(idx, q->n_bd); q->read_ptr != idx; |
| 2471 |
q->read_ptr = il_queue_inc_wrap(q->read_ptr, q->n_bd)) { |
| 2472 |
|
| 2473 |
skb = txq->skbs[txq->q.read_ptr]; |
| 2474 |
|
| 2475 |
if (WARN_ON_ONCE(skb == NULL)) |
| 2476 |
continue; |
| 2477 |
|
| 2478 |
hdr = (struct ieee80211_hdr *) skb->data; |
| 2479 |
if (ieee80211_is_data_qos(hdr->frame_control)) |
| 2480 |
nfreed++; |
| 2481 |
|
| 2482 |
il4965_tx_status(il, skb, txq_id >= IL4965_FIRST_AMPDU_QUEUE); |
| 2483 |
|
| 2484 |
txq->skbs[txq->q.read_ptr] = NULL; |
| 2485 |
il->ops->txq_free_tfd(il, txq); |
| 2486 |
} |
| 2487 |
return nfreed; |
| 2488 |
} |
| 2489 |
|
| 2490 |
/* |
| 2491 |
* il4965_tx_status_reply_compressed_ba - Update tx status from block-ack |
| 2492 |
* |
| 2493 |
* Go through block-ack's bitmap of ACK'd frames, update driver's record of |
| 2494 |
* ACK vs. not. This gets sent to mac80211, then to rate scaling algo. |
| 2495 |
*/ |
| 2496 |
static int |
| 2497 |
il4965_tx_status_reply_compressed_ba(struct il_priv *il, struct il_ht_agg *agg, |
| 2498 |
struct il_compressed_ba_resp *ba_resp) |
| 2499 |
{ |
| 2500 |
int i, sh, ack; |
| 2501 |
u16 seq_ctl = le16_to_cpu(ba_resp->seq_ctl); |
| 2502 |
u16 scd_flow = le16_to_cpu(ba_resp->scd_flow); |
| 2503 |
int successes = 0; |
| 2504 |
struct ieee80211_tx_info *info; |
| 2505 |
u64 bitmap, sent_bitmap; |
| 2506 |
|
| 2507 |
if (unlikely(!agg->wait_for_ba)) { |
| 2508 |
if (unlikely(ba_resp->bitmap)) |
| 2509 |
IL_ERR("Received BA when not expected\n"); |
| 2510 |
return -EINVAL; |
| 2511 |
} |
| 2512 |
|
| 2513 |
/* Mark that the expected block-ack response arrived */ |
| 2514 |
agg->wait_for_ba = 0; |
| 2515 |
D_TX_REPLY("BA %d %d\n", agg->start_idx, ba_resp->seq_ctl); |
| 2516 |
|
| 2517 |
/* Calculate shift to align block-ack bits with our Tx win bits */ |
| 2518 |
sh = agg->start_idx - SEQ_TO_IDX(seq_ctl >> 4); |
| 2519 |
if (sh < 0) /* tbw something is wrong with indices */ |
| 2520 |
sh += 0x100; |
| 2521 |
|
| 2522 |
if (agg->frame_count > (64 - sh)) { |
| 2523 |
D_TX_REPLY("more frames than bitmap size"); |
| 2524 |
return -1; |
| 2525 |
} |
| 2526 |
|
| 2527 |
/* don't use 64-bit values for now */ |
| 2528 |
bitmap = le64_to_cpu(ba_resp->bitmap) >> sh; |
| 2529 |
|
| 2530 |
/* check for success or failure according to the |
| 2531 |
* transmitted bitmap and block-ack bitmap */ |
| 2532 |
sent_bitmap = bitmap & agg->bitmap; |
| 2533 |
|
| 2534 |
/* For each frame attempted in aggregation, |
| 2535 |
* update driver's record of tx frame's status. */ |
| 2536 |
i = 0; |
| 2537 |
while (sent_bitmap) { |
| 2538 |
ack = sent_bitmap & 1ULL; |
| 2539 |
successes += ack; |
| 2540 |
D_TX_REPLY("%s ON i=%d idx=%d raw=%d\n", ack ? "ACK" : "NACK", |
| 2541 |
i, (agg->start_idx + i) & 0xff, agg->start_idx + i); |
| 2542 |
sent_bitmap >>= 1; |
| 2543 |
++i; |
| 2544 |
} |
| 2545 |
|
| 2546 |
D_TX_REPLY("Bitmap %llx\n", (unsigned long long)bitmap); |
| 2547 |
|
| 2548 |
info = IEEE80211_SKB_CB(il->txq[scd_flow].skbs[agg->start_idx]); |
| 2549 |
memset(&info->status, 0, sizeof(info->status)); |
| 2550 |
info->flags |= IEEE80211_TX_STAT_ACK; |
| 2551 |
info->flags |= IEEE80211_TX_STAT_AMPDU; |
| 2552 |
info->status.ampdu_ack_len = successes; |
| 2553 |
info->status.ampdu_len = agg->frame_count; |
| 2554 |
il4965_hwrate_to_tx_control(il, agg->rate_n_flags, info); |
| 2555 |
|
| 2556 |
return 0; |
| 2557 |
} |
| 2558 |
|
| 2559 |
static inline bool |
| 2560 |
il4965_is_tx_success(u32 status) |
| 2561 |
{ |
| 2562 |
status &= TX_STATUS_MSK; |
| 2563 |
return (status == TX_STATUS_SUCCESS || status == TX_STATUS_DIRECT_DONE); |
| 2564 |
} |
| 2565 |
|
| 2566 |
static u8 |
| 2567 |
il4965_find_station(struct il_priv *il, const u8 *addr) |
| 2568 |
{ |
| 2569 |
int i; |
| 2570 |
int start = 0; |
| 2571 |
int ret = IL_INVALID_STATION; |
| 2572 |
unsigned long flags; |
| 2573 |
|
| 2574 |
if (il->iw_mode == NL80211_IFTYPE_ADHOC) |
| 2575 |
start = IL_STA_ID; |
| 2576 |
|
| 2577 |
if (is_broadcast_ether_addr(addr)) |
| 2578 |
return il->hw_params.bcast_id; |
| 2579 |
|
| 2580 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 2581 |
for (i = start; i < il->hw_params.max_stations; i++) |
| 2582 |
if (il->stations[i].used && |
| 2583 |
ether_addr_equal(il->stations[i].sta.sta.addr, addr)) { |
| 2584 |
ret = i; |
| 2585 |
goto out; |
| 2586 |
} |
| 2587 |
|
| 2588 |
D_ASSOC("can not find STA %pM total %d\n", addr, il->num_stations); |
| 2589 |
|
| 2590 |
out: |
| 2591 |
/* |
| 2592 |
* It may be possible that more commands interacting with stations |
| 2593 |
* arrive before we completed processing the adding of |
| 2594 |
* station |
| 2595 |
*/ |
| 2596 |
if (ret != IL_INVALID_STATION && |
| 2597 |
(!(il->stations[ret].used & IL_STA_UCODE_ACTIVE) || |
| 2598 |
(il->stations[ret].used & IL_STA_UCODE_INPROGRESS))) { |
| 2599 |
IL_ERR("Requested station info for sta %d before ready.\n", |
| 2600 |
ret); |
| 2601 |
ret = IL_INVALID_STATION; |
| 2602 |
} |
| 2603 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 2604 |
return ret; |
| 2605 |
} |
| 2606 |
|
| 2607 |
static int |
| 2608 |
il4965_get_ra_sta_id(struct il_priv *il, struct ieee80211_hdr *hdr) |
| 2609 |
{ |
| 2610 |
if (il->iw_mode == NL80211_IFTYPE_STATION) |
| 2611 |
return IL_AP_ID; |
| 2612 |
else { |
| 2613 |
u8 *da = ieee80211_get_DA(hdr); |
| 2614 |
|
| 2615 |
return il4965_find_station(il, da); |
| 2616 |
} |
| 2617 |
} |
| 2618 |
|
| 2619 |
static inline u32 |
| 2620 |
il4965_get_scd_ssn(struct il4965_tx_resp *tx_resp) |
| 2621 |
{ |
| 2622 |
return le32_to_cpup(&tx_resp->u.status + |
| 2623 |
tx_resp->frame_count) & IEEE80211_MAX_SN; |
| 2624 |
} |
| 2625 |
|
| 2626 |
static inline u32 |
| 2627 |
il4965_tx_status_to_mac80211(u32 status) |
| 2628 |
{ |
| 2629 |
status &= TX_STATUS_MSK; |
| 2630 |
|
| 2631 |
switch (status) { |
| 2632 |
case TX_STATUS_SUCCESS: |
| 2633 |
case TX_STATUS_DIRECT_DONE: |
| 2634 |
return IEEE80211_TX_STAT_ACK; |
| 2635 |
case TX_STATUS_FAIL_DEST_PS: |
| 2636 |
return IEEE80211_TX_STAT_TX_FILTERED; |
| 2637 |
default: |
| 2638 |
return 0; |
| 2639 |
} |
| 2640 |
} |
| 2641 |
|
| 2642 |
/* |
| 2643 |
* il4965_tx_status_reply_tx - Handle Tx response for frames in aggregation queue |
| 2644 |
*/ |
| 2645 |
static int |
| 2646 |
il4965_tx_status_reply_tx(struct il_priv *il, struct il_ht_agg *agg, |
| 2647 |
struct il4965_tx_resp *tx_resp, int txq_id, |
| 2648 |
u16 start_idx) |
| 2649 |
{ |
| 2650 |
u16 status; |
| 2651 |
struct agg_tx_status *frame_status = tx_resp->u.agg_status; |
| 2652 |
struct ieee80211_tx_info *info = NULL; |
| 2653 |
struct ieee80211_hdr *hdr = NULL; |
| 2654 |
u32 rate_n_flags = le32_to_cpu(tx_resp->rate_n_flags); |
| 2655 |
int i, sh, idx; |
| 2656 |
u16 seq; |
| 2657 |
if (agg->wait_for_ba) |
| 2658 |
D_TX_REPLY("got tx response w/o block-ack\n"); |
| 2659 |
|
| 2660 |
agg->frame_count = tx_resp->frame_count; |
| 2661 |
agg->start_idx = start_idx; |
| 2662 |
agg->rate_n_flags = rate_n_flags; |
| 2663 |
agg->bitmap = 0; |
| 2664 |
|
| 2665 |
/* num frames attempted by Tx command */ |
| 2666 |
if (agg->frame_count == 1) { |
| 2667 |
/* Only one frame was attempted; no block-ack will arrive */ |
| 2668 |
status = le16_to_cpu(frame_status[0].status); |
| 2669 |
idx = start_idx; |
| 2670 |
|
| 2671 |
D_TX_REPLY("FrameCnt = %d, StartIdx=%d idx=%d\n", |
| 2672 |
agg->frame_count, agg->start_idx, idx); |
| 2673 |
|
| 2674 |
info = IEEE80211_SKB_CB(il->txq[txq_id].skbs[idx]); |
| 2675 |
info->status.rates[0].count = tx_resp->failure_frame + 1; |
| 2676 |
info->flags &= ~IEEE80211_TX_CTL_AMPDU; |
| 2677 |
info->flags |= il4965_tx_status_to_mac80211(status); |
| 2678 |
il4965_hwrate_to_tx_control(il, rate_n_flags, info); |
| 2679 |
|
| 2680 |
D_TX_REPLY("1 Frame 0x%x failure :%d\n", status & 0xff, |
| 2681 |
tx_resp->failure_frame); |
| 2682 |
D_TX_REPLY("Rate Info rate_n_flags=%x\n", rate_n_flags); |
| 2683 |
|
| 2684 |
agg->wait_for_ba = 0; |
| 2685 |
} else { |
| 2686 |
/* Two or more frames were attempted; expect block-ack */ |
| 2687 |
u64 bitmap = 0; |
| 2688 |
int start = agg->start_idx; |
| 2689 |
struct sk_buff *skb; |
| 2690 |
|
| 2691 |
/* Construct bit-map of pending frames within Tx win */ |
| 2692 |
for (i = 0; i < agg->frame_count; i++) { |
| 2693 |
u16 sc; |
| 2694 |
status = le16_to_cpu(frame_status[i].status); |
| 2695 |
seq = le16_to_cpu(frame_status[i].sequence); |
| 2696 |
idx = SEQ_TO_IDX(seq); |
| 2697 |
txq_id = SEQ_TO_QUEUE(seq); |
| 2698 |
|
| 2699 |
if (status & |
| 2700 |
(AGG_TX_STATE_FEW_BYTES_MSK | |
| 2701 |
AGG_TX_STATE_ABORT_MSK)) |
| 2702 |
continue; |
| 2703 |
|
| 2704 |
D_TX_REPLY("FrameCnt = %d, txq_id=%d idx=%d\n", |
| 2705 |
agg->frame_count, txq_id, idx); |
| 2706 |
|
| 2707 |
skb = il->txq[txq_id].skbs[idx]; |
| 2708 |
if (WARN_ON_ONCE(skb == NULL)) |
| 2709 |
return -1; |
| 2710 |
hdr = (struct ieee80211_hdr *) skb->data; |
| 2711 |
|
| 2712 |
sc = le16_to_cpu(hdr->seq_ctrl); |
| 2713 |
if (idx != (IEEE80211_SEQ_TO_SN(sc) & 0xff)) { |
| 2714 |
IL_ERR("BUG_ON idx doesn't match seq control" |
| 2715 |
" idx=%d, seq_idx=%d, seq=%d\n", idx, |
| 2716 |
IEEE80211_SEQ_TO_SN(sc), hdr->seq_ctrl); |
| 2717 |
return -1; |
| 2718 |
} |
| 2719 |
|
| 2720 |
D_TX_REPLY("AGG Frame i=%d idx %d seq=%d\n", i, idx, |
| 2721 |
IEEE80211_SEQ_TO_SN(sc)); |
| 2722 |
|
| 2723 |
sh = idx - start; |
| 2724 |
if (sh > 64) { |
| 2725 |
sh = (start - idx) + 0xff; |
| 2726 |
bitmap = bitmap << sh; |
| 2727 |
sh = 0; |
| 2728 |
start = idx; |
| 2729 |
} else if (sh < -64) |
| 2730 |
sh = 0xff - (start - idx); |
| 2731 |
else if (sh < 0) { |
| 2732 |
sh = start - idx; |
| 2733 |
start = idx; |
| 2734 |
bitmap = bitmap << sh; |
| 2735 |
sh = 0; |
| 2736 |
} |
| 2737 |
bitmap |= 1ULL << sh; |
| 2738 |
D_TX_REPLY("start=%d bitmap=0x%llx\n", start, |
| 2739 |
(unsigned long long)bitmap); |
| 2740 |
} |
| 2741 |
|
| 2742 |
agg->bitmap = bitmap; |
| 2743 |
agg->start_idx = start; |
| 2744 |
D_TX_REPLY("Frames %d start_idx=%d bitmap=0x%llx\n", |
| 2745 |
agg->frame_count, agg->start_idx, |
| 2746 |
(unsigned long long)agg->bitmap); |
| 2747 |
|
| 2748 |
if (bitmap) |
| 2749 |
agg->wait_for_ba = 1; |
| 2750 |
} |
| 2751 |
return 0; |
| 2752 |
} |
| 2753 |
|
| 2754 |
/* |
| 2755 |
* il4965_hdl_tx - Handle standard (non-aggregation) Tx response |
| 2756 |
*/ |
| 2757 |
static void |
| 2758 |
il4965_hdl_tx(struct il_priv *il, struct il_rx_buf *rxb) |
| 2759 |
{ |
| 2760 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 2761 |
u16 sequence = le16_to_cpu(pkt->hdr.sequence); |
| 2762 |
int txq_id = SEQ_TO_QUEUE(sequence); |
| 2763 |
int idx = SEQ_TO_IDX(sequence); |
| 2764 |
struct il_tx_queue *txq = &il->txq[txq_id]; |
| 2765 |
struct sk_buff *skb; |
| 2766 |
struct ieee80211_hdr *hdr; |
| 2767 |
struct ieee80211_tx_info *info; |
| 2768 |
struct il4965_tx_resp *tx_resp = (void *)&pkt->u.raw[0]; |
| 2769 |
u32 status = le32_to_cpu(tx_resp->u.status); |
| 2770 |
int tid; |
| 2771 |
int sta_id; |
| 2772 |
int freed; |
| 2773 |
u8 *qc = NULL; |
| 2774 |
unsigned long flags; |
| 2775 |
|
| 2776 |
if (idx >= txq->q.n_bd || il_queue_used(&txq->q, idx) == 0) { |
| 2777 |
IL_ERR("Read idx for DMA queue txq_id (%d) idx %d " |
| 2778 |
"is out of range [0-%d] %d %d\n", txq_id, idx, |
| 2779 |
txq->q.n_bd, txq->q.write_ptr, txq->q.read_ptr); |
| 2780 |
return; |
| 2781 |
} |
| 2782 |
|
| 2783 |
txq->time_stamp = jiffies; |
| 2784 |
|
| 2785 |
skb = txq->skbs[txq->q.read_ptr]; |
| 2786 |
info = IEEE80211_SKB_CB(skb); |
| 2787 |
memset(&info->status, 0, sizeof(info->status)); |
| 2788 |
|
| 2789 |
hdr = (struct ieee80211_hdr *) skb->data; |
| 2790 |
if (ieee80211_is_data_qos(hdr->frame_control)) { |
| 2791 |
qc = ieee80211_get_qos_ctl(hdr); |
| 2792 |
tid = qc[0] & 0xf; |
| 2793 |
} |
| 2794 |
|
| 2795 |
sta_id = il4965_get_ra_sta_id(il, hdr); |
| 2796 |
if (txq->sched_retry && unlikely(sta_id == IL_INVALID_STATION)) { |
| 2797 |
IL_ERR("Station not known\n"); |
| 2798 |
return; |
| 2799 |
} |
| 2800 |
|
| 2801 |
/* |
| 2802 |
* Firmware will not transmit frame on passive channel, if it not yet |
| 2803 |
* received some valid frame on that channel. When this error happen |
| 2804 |
* we have to wait until firmware will unblock itself i.e. when we |
| 2805 |
* note received beacon or other frame. We unblock queues in |
| 2806 |
* il4965_pass_packet_to_mac80211 or in il_mac_bss_info_changed. |
| 2807 |
*/ |
| 2808 |
if (unlikely((status & TX_STATUS_MSK) == TX_STATUS_FAIL_PASSIVE_NO_RX) && |
| 2809 |
il->iw_mode == NL80211_IFTYPE_STATION) { |
| 2810 |
il_stop_queues_by_reason(il, IL_STOP_REASON_PASSIVE); |
| 2811 |
D_INFO("Stopped queues - RX waiting on passive channel\n"); |
| 2812 |
} |
| 2813 |
|
| 2814 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 2815 |
if (txq->sched_retry) { |
| 2816 |
const u32 scd_ssn = il4965_get_scd_ssn(tx_resp); |
| 2817 |
struct il_ht_agg *agg; |
| 2818 |
|
| 2819 |
if (WARN_ON(!qc)) |
| 2820 |
goto out; |
| 2821 |
|
| 2822 |
agg = &il->stations[sta_id].tid[tid].agg; |
| 2823 |
|
| 2824 |
il4965_tx_status_reply_tx(il, agg, tx_resp, txq_id, idx); |
| 2825 |
|
| 2826 |
/* check if BAR is needed */ |
| 2827 |
if (tx_resp->frame_count == 1 && |
| 2828 |
!il4965_is_tx_success(status)) |
| 2829 |
info->flags |= IEEE80211_TX_STAT_AMPDU_NO_BACK; |
| 2830 |
|
| 2831 |
if (txq->q.read_ptr != (scd_ssn & 0xff)) { |
| 2832 |
idx = il_queue_dec_wrap(scd_ssn & 0xff, txq->q.n_bd); |
| 2833 |
D_TX_REPLY("Retry scheduler reclaim scd_ssn " |
| 2834 |
"%d idx %d\n", scd_ssn, idx); |
| 2835 |
freed = il4965_tx_queue_reclaim(il, txq_id, idx); |
| 2836 |
il4965_free_tfds_in_queue(il, sta_id, tid, freed); |
| 2837 |
|
| 2838 |
if (il->mac80211_registered && |
| 2839 |
il_queue_space(&txq->q) > txq->q.low_mark && |
| 2840 |
agg->state != IL_EMPTYING_HW_QUEUE_DELBA) |
| 2841 |
il_wake_queue(il, txq); |
| 2842 |
} |
| 2843 |
} else { |
| 2844 |
info->status.rates[0].count = tx_resp->failure_frame + 1; |
| 2845 |
info->flags |= il4965_tx_status_to_mac80211(status); |
| 2846 |
il4965_hwrate_to_tx_control(il, |
| 2847 |
le32_to_cpu(tx_resp->rate_n_flags), |
| 2848 |
info); |
| 2849 |
|
| 2850 |
D_TX_REPLY("TXQ %d status %s (0x%08x) " |
| 2851 |
"rate_n_flags 0x%x retries %d\n", txq_id, |
| 2852 |
il4965_get_tx_fail_reason(status), status, |
| 2853 |
le32_to_cpu(tx_resp->rate_n_flags), |
| 2854 |
tx_resp->failure_frame); |
| 2855 |
|
| 2856 |
freed = il4965_tx_queue_reclaim(il, txq_id, idx); |
| 2857 |
if (qc && likely(sta_id != IL_INVALID_STATION)) |
| 2858 |
il4965_free_tfds_in_queue(il, sta_id, tid, freed); |
| 2859 |
else if (sta_id == IL_INVALID_STATION) |
| 2860 |
D_TX_REPLY("Station not known\n"); |
| 2861 |
|
| 2862 |
if (il->mac80211_registered && |
| 2863 |
il_queue_space(&txq->q) > txq->q.low_mark) |
| 2864 |
il_wake_queue(il, txq); |
| 2865 |
} |
| 2866 |
out: |
| 2867 |
if (qc && likely(sta_id != IL_INVALID_STATION)) |
| 2868 |
il4965_txq_check_empty(il, sta_id, tid, txq_id); |
| 2869 |
|
| 2870 |
il4965_check_abort_status(il, tx_resp->frame_count, status); |
| 2871 |
|
| 2872 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 2873 |
} |
| 2874 |
|
| 2875 |
/* |
| 2876 |
* translate ucode response to mac80211 tx status control values |
| 2877 |
*/ |
| 2878 |
void |
| 2879 |
il4965_hwrate_to_tx_control(struct il_priv *il, u32 rate_n_flags, |
| 2880 |
struct ieee80211_tx_info *info) |
| 2881 |
{ |
| 2882 |
struct ieee80211_tx_rate *r = &info->status.rates[0]; |
| 2883 |
|
| 2884 |
info->status.antenna = |
| 2885 |
((rate_n_flags & RATE_MCS_ANT_ABC_MSK) >> RATE_MCS_ANT_POS); |
| 2886 |
if (rate_n_flags & RATE_MCS_HT_MSK) |
| 2887 |
r->flags |= IEEE80211_TX_RC_MCS; |
| 2888 |
if (rate_n_flags & RATE_MCS_GF_MSK) |
| 2889 |
r->flags |= IEEE80211_TX_RC_GREEN_FIELD; |
| 2890 |
if (rate_n_flags & RATE_MCS_HT40_MSK) |
| 2891 |
r->flags |= IEEE80211_TX_RC_40_MHZ_WIDTH; |
| 2892 |
if (rate_n_flags & RATE_MCS_DUP_MSK) |
| 2893 |
r->flags |= IEEE80211_TX_RC_DUP_DATA; |
| 2894 |
if (rate_n_flags & RATE_MCS_SGI_MSK) |
| 2895 |
r->flags |= IEEE80211_TX_RC_SHORT_GI; |
| 2896 |
r->idx = il4965_hwrate_to_mac80211_idx(rate_n_flags, info->band); |
| 2897 |
} |
| 2898 |
|
| 2899 |
/* |
| 2900 |
* il4965_hdl_compressed_ba - Handler for N_COMPRESSED_BA |
| 2901 |
* |
| 2902 |
* Handles block-acknowledge notification from device, which reports success |
| 2903 |
* of frames sent via aggregation. |
| 2904 |
*/ |
| 2905 |
static void |
| 2906 |
il4965_hdl_compressed_ba(struct il_priv *il, struct il_rx_buf *rxb) |
| 2907 |
{ |
| 2908 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 2909 |
struct il_compressed_ba_resp *ba_resp = &pkt->u.compressed_ba; |
| 2910 |
struct il_tx_queue *txq = NULL; |
| 2911 |
struct il_ht_agg *agg; |
| 2912 |
int idx; |
| 2913 |
int sta_id; |
| 2914 |
int tid; |
| 2915 |
unsigned long flags; |
| 2916 |
|
| 2917 |
/* "flow" corresponds to Tx queue */ |
| 2918 |
u16 scd_flow = le16_to_cpu(ba_resp->scd_flow); |
| 2919 |
|
| 2920 |
/* "ssn" is start of block-ack Tx win, corresponds to idx |
| 2921 |
* (in Tx queue's circular buffer) of first TFD/frame in win */ |
| 2922 |
u16 ba_resp_scd_ssn = le16_to_cpu(ba_resp->scd_ssn); |
| 2923 |
|
| 2924 |
if (scd_flow >= il->hw_params.max_txq_num) { |
| 2925 |
IL_ERR("BUG_ON scd_flow is bigger than number of queues\n"); |
| 2926 |
return; |
| 2927 |
} |
| 2928 |
|
| 2929 |
txq = &il->txq[scd_flow]; |
| 2930 |
sta_id = ba_resp->sta_id; |
| 2931 |
tid = ba_resp->tid; |
| 2932 |
agg = &il->stations[sta_id].tid[tid].agg; |
| 2933 |
if (unlikely(agg->txq_id != scd_flow)) { |
| 2934 |
/* |
| 2935 |
* FIXME: this is a uCode bug which need to be addressed, |
| 2936 |
* log the information and return for now! |
| 2937 |
* since it is possible happen very often and in order |
| 2938 |
* not to fill the syslog, don't enable the logging by default |
| 2939 |
*/ |
| 2940 |
D_TX_REPLY("BA scd_flow %d does not match txq_id %d\n", |
| 2941 |
scd_flow, agg->txq_id); |
| 2942 |
return; |
| 2943 |
} |
| 2944 |
|
| 2945 |
/* Find idx just before block-ack win */ |
| 2946 |
idx = il_queue_dec_wrap(ba_resp_scd_ssn & 0xff, txq->q.n_bd); |
| 2947 |
|
| 2948 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 2949 |
|
| 2950 |
D_TX_REPLY("N_COMPRESSED_BA [%d] Received from %pM, " "sta_id = %d\n", |
| 2951 |
agg->wait_for_ba, (u8 *) &ba_resp->sta_addr_lo32, |
| 2952 |
ba_resp->sta_id); |
| 2953 |
D_TX_REPLY("TID = %d, SeqCtl = %d, bitmap = 0x%llx," "scd_flow = " |
| 2954 |
"%d, scd_ssn = %d\n", ba_resp->tid, ba_resp->seq_ctl, |
| 2955 |
(unsigned long long)le64_to_cpu(ba_resp->bitmap), |
| 2956 |
ba_resp->scd_flow, ba_resp->scd_ssn); |
| 2957 |
D_TX_REPLY("DAT start_idx = %d, bitmap = 0x%llx\n", agg->start_idx, |
| 2958 |
(unsigned long long)agg->bitmap); |
| 2959 |
|
| 2960 |
/* Update driver's record of ACK vs. not for each frame in win */ |
| 2961 |
il4965_tx_status_reply_compressed_ba(il, agg, ba_resp); |
| 2962 |
|
| 2963 |
/* Release all TFDs before the SSN, i.e. all TFDs in front of |
| 2964 |
* block-ack win (we assume that they've been successfully |
| 2965 |
* transmitted ... if not, it's too late anyway). */ |
| 2966 |
if (txq->q.read_ptr != (ba_resp_scd_ssn & 0xff)) { |
| 2967 |
/* calculate mac80211 ampdu sw queue to wake */ |
| 2968 |
int freed = il4965_tx_queue_reclaim(il, scd_flow, idx); |
| 2969 |
il4965_free_tfds_in_queue(il, sta_id, tid, freed); |
| 2970 |
|
| 2971 |
if (il_queue_space(&txq->q) > txq->q.low_mark && |
| 2972 |
il->mac80211_registered && |
| 2973 |
agg->state != IL_EMPTYING_HW_QUEUE_DELBA) |
| 2974 |
il_wake_queue(il, txq); |
| 2975 |
|
| 2976 |
il4965_txq_check_empty(il, sta_id, tid, scd_flow); |
| 2977 |
} |
| 2978 |
|
| 2979 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 2980 |
} |
| 2981 |
|
| 2982 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 2983 |
const char * |
| 2984 |
il4965_get_tx_fail_reason(u32 status) |
| 2985 |
{ |
| 2986 |
#define TX_STATUS_FAIL(x) case TX_STATUS_FAIL_ ## x: return #x |
| 2987 |
#define TX_STATUS_POSTPONE(x) case TX_STATUS_POSTPONE_ ## x: return #x |
| 2988 |
|
| 2989 |
switch (status & TX_STATUS_MSK) { |
| 2990 |
case TX_STATUS_SUCCESS: |
| 2991 |
return "SUCCESS"; |
| 2992 |
TX_STATUS_POSTPONE(DELAY); |
| 2993 |
TX_STATUS_POSTPONE(FEW_BYTES); |
| 2994 |
TX_STATUS_POSTPONE(QUIET_PERIOD); |
| 2995 |
TX_STATUS_POSTPONE(CALC_TTAK); |
| 2996 |
TX_STATUS_FAIL(INTERNAL_CROSSED_RETRY); |
| 2997 |
TX_STATUS_FAIL(SHORT_LIMIT); |
| 2998 |
TX_STATUS_FAIL(LONG_LIMIT); |
| 2999 |
TX_STATUS_FAIL(FIFO_UNDERRUN); |
| 3000 |
TX_STATUS_FAIL(DRAIN_FLOW); |
| 3001 |
TX_STATUS_FAIL(RFKILL_FLUSH); |
| 3002 |
TX_STATUS_FAIL(LIFE_EXPIRE); |
| 3003 |
TX_STATUS_FAIL(DEST_PS); |
| 3004 |
TX_STATUS_FAIL(HOST_ABORTED); |
| 3005 |
TX_STATUS_FAIL(BT_RETRY); |
| 3006 |
TX_STATUS_FAIL(STA_INVALID); |
| 3007 |
TX_STATUS_FAIL(FRAG_DROPPED); |
| 3008 |
TX_STATUS_FAIL(TID_DISABLE); |
| 3009 |
TX_STATUS_FAIL(FIFO_FLUSHED); |
| 3010 |
TX_STATUS_FAIL(INSUFFICIENT_CF_POLL); |
| 3011 |
TX_STATUS_FAIL(PASSIVE_NO_RX); |
| 3012 |
TX_STATUS_FAIL(NO_BEACON_ON_RADAR); |
| 3013 |
} |
| 3014 |
|
| 3015 |
return "UNKNOWN"; |
| 3016 |
|
| 3017 |
#undef TX_STATUS_FAIL |
| 3018 |
#undef TX_STATUS_POSTPONE |
| 3019 |
} |
| 3020 |
#endif /* CONFIG_IWLEGACY_DEBUG */ |
| 3021 |
|
| 3022 |
static struct il_link_quality_cmd * |
| 3023 |
il4965_sta_alloc_lq(struct il_priv *il, u8 sta_id) |
| 3024 |
{ |
| 3025 |
int i, r; |
| 3026 |
struct il_link_quality_cmd *link_cmd; |
| 3027 |
u32 rate_flags = 0; |
| 3028 |
__le32 rate_n_flags; |
| 3029 |
|
| 3030 |
link_cmd = kzalloc_obj(struct il_link_quality_cmd); |
| 3031 |
if (!link_cmd) { |
| 3032 |
IL_ERR("Unable to allocate memory for LQ cmd.\n"); |
| 3033 |
return NULL; |
| 3034 |
} |
| 3035 |
/* Set up the rate scaling to start at selected rate, fall back |
| 3036 |
* all the way down to 1M in IEEE order, and then spin on 1M */ |
| 3037 |
if (il->band == NL80211_BAND_5GHZ) |
| 3038 |
r = RATE_6M_IDX; |
| 3039 |
else |
| 3040 |
r = RATE_1M_IDX; |
| 3041 |
|
| 3042 |
if (r >= IL_FIRST_CCK_RATE && r <= IL_LAST_CCK_RATE) |
| 3043 |
rate_flags |= RATE_MCS_CCK_MSK; |
| 3044 |
|
| 3045 |
rate_flags |= |
| 3046 |
il4965_first_antenna(il->hw_params. |
| 3047 |
valid_tx_ant) << RATE_MCS_ANT_POS; |
| 3048 |
rate_n_flags = cpu_to_le32(il_rates[r].plcp | rate_flags); |
| 3049 |
for (i = 0; i < LINK_QUAL_MAX_RETRY_NUM; i++) |
| 3050 |
link_cmd->rs_table[i].rate_n_flags = rate_n_flags; |
| 3051 |
|
| 3052 |
link_cmd->general_params.single_stream_ant_msk = |
| 3053 |
il4965_first_antenna(il->hw_params.valid_tx_ant); |
| 3054 |
|
| 3055 |
link_cmd->general_params.dual_stream_ant_msk = |
| 3056 |
il->hw_params.valid_tx_ant & ~il4965_first_antenna(il->hw_params. |
| 3057 |
valid_tx_ant); |
| 3058 |
if (!link_cmd->general_params.dual_stream_ant_msk) { |
| 3059 |
link_cmd->general_params.dual_stream_ant_msk = ANT_AB; |
| 3060 |
} else if (il4965_num_of_ant(il->hw_params.valid_tx_ant) == 2) { |
| 3061 |
link_cmd->general_params.dual_stream_ant_msk = |
| 3062 |
il->hw_params.valid_tx_ant; |
| 3063 |
} |
| 3064 |
|
| 3065 |
link_cmd->agg_params.agg_dis_start_th = LINK_QUAL_AGG_DISABLE_START_DEF; |
| 3066 |
link_cmd->agg_params.agg_time_limit = |
| 3067 |
cpu_to_le16(LINK_QUAL_AGG_TIME_LIMIT_DEF); |
| 3068 |
|
| 3069 |
link_cmd->sta_id = sta_id; |
| 3070 |
|
| 3071 |
return link_cmd; |
| 3072 |
} |
| 3073 |
|
| 3074 |
/* |
| 3075 |
* il4965_add_bssid_station - Add the special IBSS BSSID station |
| 3076 |
* |
| 3077 |
* Function sleeps. |
| 3078 |
*/ |
| 3079 |
int |
| 3080 |
il4965_add_bssid_station(struct il_priv *il, const u8 *addr, u8 *sta_id_r) |
| 3081 |
{ |
| 3082 |
int ret; |
| 3083 |
u8 sta_id; |
| 3084 |
struct il_link_quality_cmd *link_cmd; |
| 3085 |
unsigned long flags; |
| 3086 |
|
| 3087 |
if (sta_id_r) |
| 3088 |
*sta_id_r = IL_INVALID_STATION; |
| 3089 |
|
| 3090 |
ret = il_add_station_common(il, addr, 0, NULL, &sta_id); |
| 3091 |
if (ret) { |
| 3092 |
IL_ERR("Unable to add station %pM\n", addr); |
| 3093 |
return ret; |
| 3094 |
} |
| 3095 |
|
| 3096 |
if (sta_id_r) |
| 3097 |
*sta_id_r = sta_id; |
| 3098 |
|
| 3099 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3100 |
il->stations[sta_id].used |= IL_STA_LOCAL; |
| 3101 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3102 |
|
| 3103 |
/* Set up default rate scaling table in device's station table */ |
| 3104 |
link_cmd = il4965_sta_alloc_lq(il, sta_id); |
| 3105 |
if (!link_cmd) { |
| 3106 |
IL_ERR("Unable to initialize rate scaling for station %pM.\n", |
| 3107 |
addr); |
| 3108 |
return -ENOMEM; |
| 3109 |
} |
| 3110 |
|
| 3111 |
ret = il_send_lq_cmd(il, link_cmd, CMD_SYNC, true); |
| 3112 |
if (ret) |
| 3113 |
IL_ERR("Link quality command failed (%d)\n", ret); |
| 3114 |
|
| 3115 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3116 |
il->stations[sta_id].lq = link_cmd; |
| 3117 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3118 |
|
| 3119 |
return 0; |
| 3120 |
} |
| 3121 |
|
| 3122 |
static int |
| 3123 |
il4965_static_wepkey_cmd(struct il_priv *il, bool send_if_empty) |
| 3124 |
{ |
| 3125 |
int i; |
| 3126 |
u8 buff[sizeof(struct il_wep_cmd) + |
| 3127 |
sizeof(struct il_wep_key) * WEP_KEYS_MAX]; |
| 3128 |
struct il_wep_cmd *wep_cmd = (struct il_wep_cmd *)buff; |
| 3129 |
size_t cmd_size = sizeof(struct il_wep_cmd); |
| 3130 |
struct il_host_cmd cmd = { |
| 3131 |
.id = C_WEPKEY, |
| 3132 |
.data = wep_cmd, |
| 3133 |
.flags = CMD_SYNC, |
| 3134 |
}; |
| 3135 |
bool not_empty = false; |
| 3136 |
|
| 3137 |
might_sleep(); |
| 3138 |
|
| 3139 |
memset(wep_cmd, 0, |
| 3140 |
cmd_size + (sizeof(struct il_wep_key) * WEP_KEYS_MAX)); |
| 3141 |
|
| 3142 |
for (i = 0; i < WEP_KEYS_MAX; i++) { |
| 3143 |
u8 key_size = il->_4965.wep_keys[i].key_size; |
| 3144 |
|
| 3145 |
wep_cmd->key[i].key_idx = i; |
| 3146 |
if (key_size) { |
| 3147 |
wep_cmd->key[i].key_offset = i; |
| 3148 |
not_empty = true; |
| 3149 |
} else |
| 3150 |
wep_cmd->key[i].key_offset = WEP_INVALID_OFFSET; |
| 3151 |
|
| 3152 |
wep_cmd->key[i].key_size = key_size; |
| 3153 |
memcpy(&wep_cmd->key[i].key[3], il->_4965.wep_keys[i].key, key_size); |
| 3154 |
} |
| 3155 |
|
| 3156 |
wep_cmd->global_key_type = WEP_KEY_WEP_TYPE; |
| 3157 |
wep_cmd->num_keys = WEP_KEYS_MAX; |
| 3158 |
|
| 3159 |
cmd_size += sizeof(struct il_wep_key) * WEP_KEYS_MAX; |
| 3160 |
cmd.len = cmd_size; |
| 3161 |
|
| 3162 |
if (not_empty || send_if_empty) |
| 3163 |
return il_send_cmd(il, &cmd); |
| 3164 |
else |
| 3165 |
return 0; |
| 3166 |
} |
| 3167 |
|
| 3168 |
int |
| 3169 |
il4965_restore_default_wep_keys(struct il_priv *il) |
| 3170 |
{ |
| 3171 |
lockdep_assert_held(&il->mutex); |
| 3172 |
|
| 3173 |
return il4965_static_wepkey_cmd(il, false); |
| 3174 |
} |
| 3175 |
|
| 3176 |
int |
| 3177 |
il4965_remove_default_wep_key(struct il_priv *il, |
| 3178 |
struct ieee80211_key_conf *keyconf) |
| 3179 |
{ |
| 3180 |
int ret; |
| 3181 |
int idx = keyconf->keyidx; |
| 3182 |
|
| 3183 |
lockdep_assert_held(&il->mutex); |
| 3184 |
|
| 3185 |
D_WEP("Removing default WEP key: idx=%d\n", idx); |
| 3186 |
|
| 3187 |
memset(&il->_4965.wep_keys[idx], 0, sizeof(struct il_wep_key)); |
| 3188 |
if (il_is_rfkill(il)) { |
| 3189 |
D_WEP("Not sending C_WEPKEY command due to RFKILL.\n"); |
| 3190 |
/* but keys in device are clear anyway so return success */ |
| 3191 |
return 0; |
| 3192 |
} |
| 3193 |
ret = il4965_static_wepkey_cmd(il, 1); |
| 3194 |
D_WEP("Remove default WEP key: idx=%d ret=%d\n", idx, ret); |
| 3195 |
|
| 3196 |
return ret; |
| 3197 |
} |
| 3198 |
|
| 3199 |
int |
| 3200 |
il4965_set_default_wep_key(struct il_priv *il, |
| 3201 |
struct ieee80211_key_conf *keyconf) |
| 3202 |
{ |
| 3203 |
int ret; |
| 3204 |
int len = keyconf->keylen; |
| 3205 |
int idx = keyconf->keyidx; |
| 3206 |
|
| 3207 |
lockdep_assert_held(&il->mutex); |
| 3208 |
|
| 3209 |
if (len != WEP_KEY_LEN_128 && len != WEP_KEY_LEN_64) { |
| 3210 |
D_WEP("Bad WEP key length %d\n", keyconf->keylen); |
| 3211 |
return -EINVAL; |
| 3212 |
} |
| 3213 |
|
| 3214 |
keyconf->flags &= ~IEEE80211_KEY_FLAG_GENERATE_IV; |
| 3215 |
keyconf->hw_key_idx = HW_KEY_DEFAULT; |
| 3216 |
il->stations[IL_AP_ID].keyinfo.cipher = keyconf->cipher; |
| 3217 |
|
| 3218 |
il->_4965.wep_keys[idx].key_size = len; |
| 3219 |
memcpy(&il->_4965.wep_keys[idx].key, &keyconf->key, len); |
| 3220 |
|
| 3221 |
ret = il4965_static_wepkey_cmd(il, false); |
| 3222 |
|
| 3223 |
D_WEP("Set default WEP key: len=%d idx=%d ret=%d\n", len, idx, ret); |
| 3224 |
return ret; |
| 3225 |
} |
| 3226 |
|
| 3227 |
static int |
| 3228 |
il4965_set_wep_dynamic_key_info(struct il_priv *il, |
| 3229 |
struct ieee80211_key_conf *keyconf, u8 sta_id) |
| 3230 |
{ |
| 3231 |
unsigned long flags; |
| 3232 |
__le16 key_flags = 0; |
| 3233 |
struct il_addsta_cmd sta_cmd; |
| 3234 |
|
| 3235 |
lockdep_assert_held(&il->mutex); |
| 3236 |
|
| 3237 |
keyconf->flags &= ~IEEE80211_KEY_FLAG_GENERATE_IV; |
| 3238 |
|
| 3239 |
key_flags |= (STA_KEY_FLG_WEP | STA_KEY_FLG_MAP_KEY_MSK); |
| 3240 |
key_flags |= cpu_to_le16(keyconf->keyidx << STA_KEY_FLG_KEYID_POS); |
| 3241 |
key_flags &= ~STA_KEY_FLG_INVALID; |
| 3242 |
|
| 3243 |
if (keyconf->keylen == WEP_KEY_LEN_128) |
| 3244 |
key_flags |= STA_KEY_FLG_KEY_SIZE_MSK; |
| 3245 |
|
| 3246 |
if (sta_id == il->hw_params.bcast_id) |
| 3247 |
key_flags |= STA_KEY_MULTICAST_MSK; |
| 3248 |
|
| 3249 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3250 |
|
| 3251 |
il->stations[sta_id].keyinfo.cipher = keyconf->cipher; |
| 3252 |
il->stations[sta_id].keyinfo.keylen = keyconf->keylen; |
| 3253 |
il->stations[sta_id].keyinfo.keyidx = keyconf->keyidx; |
| 3254 |
|
| 3255 |
memcpy(il->stations[sta_id].keyinfo.key, keyconf->key, keyconf->keylen); |
| 3256 |
|
| 3257 |
memcpy(&il->stations[sta_id].sta.key.key[3], keyconf->key, |
| 3258 |
keyconf->keylen); |
| 3259 |
|
| 3260 |
if ((il->stations[sta_id].sta.key. |
| 3261 |
key_flags & STA_KEY_FLG_ENCRYPT_MSK) == STA_KEY_FLG_NO_ENC) |
| 3262 |
il->stations[sta_id].sta.key.key_offset = |
| 3263 |
il_get_free_ucode_key_idx(il); |
| 3264 |
/* else, we are overriding an existing key => no need to allocated room |
| 3265 |
* in uCode. */ |
| 3266 |
|
| 3267 |
WARN(il->stations[sta_id].sta.key.key_offset == WEP_INVALID_OFFSET, |
| 3268 |
"no space for a new key"); |
| 3269 |
|
| 3270 |
il->stations[sta_id].sta.key.key_flags = key_flags; |
| 3271 |
il->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK; |
| 3272 |
il->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; |
| 3273 |
|
| 3274 |
memcpy(&sta_cmd, &il->stations[sta_id].sta, |
| 3275 |
sizeof(struct il_addsta_cmd)); |
| 3276 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3277 |
|
| 3278 |
return il_send_add_sta(il, &sta_cmd, CMD_SYNC); |
| 3279 |
} |
| 3280 |
|
| 3281 |
static int |
| 3282 |
il4965_set_ccmp_dynamic_key_info(struct il_priv *il, |
| 3283 |
struct ieee80211_key_conf *keyconf, u8 sta_id) |
| 3284 |
{ |
| 3285 |
unsigned long flags; |
| 3286 |
__le16 key_flags = 0; |
| 3287 |
struct il_addsta_cmd sta_cmd; |
| 3288 |
|
| 3289 |
lockdep_assert_held(&il->mutex); |
| 3290 |
|
| 3291 |
key_flags |= (STA_KEY_FLG_CCMP | STA_KEY_FLG_MAP_KEY_MSK); |
| 3292 |
key_flags |= cpu_to_le16(keyconf->keyidx << STA_KEY_FLG_KEYID_POS); |
| 3293 |
key_flags &= ~STA_KEY_FLG_INVALID; |
| 3294 |
|
| 3295 |
if (sta_id == il->hw_params.bcast_id) |
| 3296 |
key_flags |= STA_KEY_MULTICAST_MSK; |
| 3297 |
|
| 3298 |
keyconf->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| 3299 |
|
| 3300 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3301 |
il->stations[sta_id].keyinfo.cipher = keyconf->cipher; |
| 3302 |
il->stations[sta_id].keyinfo.keylen = keyconf->keylen; |
| 3303 |
|
| 3304 |
memcpy(il->stations[sta_id].keyinfo.key, keyconf->key, keyconf->keylen); |
| 3305 |
|
| 3306 |
memcpy(il->stations[sta_id].sta.key.key, keyconf->key, keyconf->keylen); |
| 3307 |
|
| 3308 |
if ((il->stations[sta_id].sta.key. |
| 3309 |
key_flags & STA_KEY_FLG_ENCRYPT_MSK) == STA_KEY_FLG_NO_ENC) |
| 3310 |
il->stations[sta_id].sta.key.key_offset = |
| 3311 |
il_get_free_ucode_key_idx(il); |
| 3312 |
/* else, we are overriding an existing key => no need to allocated room |
| 3313 |
* in uCode. */ |
| 3314 |
|
| 3315 |
WARN(il->stations[sta_id].sta.key.key_offset == WEP_INVALID_OFFSET, |
| 3316 |
"no space for a new key"); |
| 3317 |
|
| 3318 |
il->stations[sta_id].sta.key.key_flags = key_flags; |
| 3319 |
il->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK; |
| 3320 |
il->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; |
| 3321 |
|
| 3322 |
memcpy(&sta_cmd, &il->stations[sta_id].sta, |
| 3323 |
sizeof(struct il_addsta_cmd)); |
| 3324 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3325 |
|
| 3326 |
return il_send_add_sta(il, &sta_cmd, CMD_SYNC); |
| 3327 |
} |
| 3328 |
|
| 3329 |
static int |
| 3330 |
il4965_set_tkip_dynamic_key_info(struct il_priv *il, |
| 3331 |
struct ieee80211_key_conf *keyconf, u8 sta_id) |
| 3332 |
{ |
| 3333 |
unsigned long flags; |
| 3334 |
__le16 key_flags = 0; |
| 3335 |
|
| 3336 |
key_flags |= (STA_KEY_FLG_TKIP | STA_KEY_FLG_MAP_KEY_MSK); |
| 3337 |
key_flags |= cpu_to_le16(keyconf->keyidx << STA_KEY_FLG_KEYID_POS); |
| 3338 |
key_flags &= ~STA_KEY_FLG_INVALID; |
| 3339 |
|
| 3340 |
if (sta_id == il->hw_params.bcast_id) |
| 3341 |
key_flags |= STA_KEY_MULTICAST_MSK; |
| 3342 |
|
| 3343 |
keyconf->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| 3344 |
keyconf->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; |
| 3345 |
|
| 3346 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3347 |
|
| 3348 |
il->stations[sta_id].keyinfo.cipher = keyconf->cipher; |
| 3349 |
il->stations[sta_id].keyinfo.keylen = 16; |
| 3350 |
|
| 3351 |
if ((il->stations[sta_id].sta.key. |
| 3352 |
key_flags & STA_KEY_FLG_ENCRYPT_MSK) == STA_KEY_FLG_NO_ENC) |
| 3353 |
il->stations[sta_id].sta.key.key_offset = |
| 3354 |
il_get_free_ucode_key_idx(il); |
| 3355 |
/* else, we are overriding an existing key => no need to allocated room |
| 3356 |
* in uCode. */ |
| 3357 |
|
| 3358 |
WARN(il->stations[sta_id].sta.key.key_offset == WEP_INVALID_OFFSET, |
| 3359 |
"no space for a new key"); |
| 3360 |
|
| 3361 |
il->stations[sta_id].sta.key.key_flags = key_flags; |
| 3362 |
|
| 3363 |
/* This copy is acutally not needed: we get the key with each TX */ |
| 3364 |
memcpy(il->stations[sta_id].keyinfo.key, keyconf->key, 16); |
| 3365 |
|
| 3366 |
memcpy(il->stations[sta_id].sta.key.key, keyconf->key, 16); |
| 3367 |
|
| 3368 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3369 |
|
| 3370 |
return 0; |
| 3371 |
} |
| 3372 |
|
| 3373 |
void |
| 3374 |
il4965_update_tkip_key(struct il_priv *il, struct ieee80211_key_conf *keyconf, |
| 3375 |
struct ieee80211_sta *sta, u32 iv32, u16 *phase1key) |
| 3376 |
{ |
| 3377 |
u8 sta_id; |
| 3378 |
unsigned long flags; |
| 3379 |
int i; |
| 3380 |
|
| 3381 |
if (il_scan_cancel(il)) { |
| 3382 |
/* cancel scan failed, just live w/ bad key and rely |
| 3383 |
briefly on SW decryption */ |
| 3384 |
return; |
| 3385 |
} |
| 3386 |
|
| 3387 |
sta_id = il_sta_id_or_broadcast(il, sta); |
| 3388 |
if (sta_id == IL_INVALID_STATION) |
| 3389 |
return; |
| 3390 |
|
| 3391 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3392 |
|
| 3393 |
il->stations[sta_id].sta.key.tkip_rx_tsc_byte2 = (u8) iv32; |
| 3394 |
|
| 3395 |
for (i = 0; i < 5; i++) |
| 3396 |
il->stations[sta_id].sta.key.tkip_rx_ttak[i] = |
| 3397 |
cpu_to_le16(phase1key[i]); |
| 3398 |
|
| 3399 |
il->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK; |
| 3400 |
il->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; |
| 3401 |
|
| 3402 |
il_send_add_sta(il, &il->stations[sta_id].sta, CMD_ASYNC); |
| 3403 |
|
| 3404 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3405 |
} |
| 3406 |
|
| 3407 |
int |
| 3408 |
il4965_remove_dynamic_key(struct il_priv *il, |
| 3409 |
struct ieee80211_key_conf *keyconf, u8 sta_id) |
| 3410 |
{ |
| 3411 |
unsigned long flags; |
| 3412 |
u16 key_flags; |
| 3413 |
u8 keyidx; |
| 3414 |
struct il_addsta_cmd sta_cmd; |
| 3415 |
|
| 3416 |
lockdep_assert_held(&il->mutex); |
| 3417 |
|
| 3418 |
il->_4965.key_mapping_keys--; |
| 3419 |
|
| 3420 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3421 |
key_flags = le16_to_cpu(il->stations[sta_id].sta.key.key_flags); |
| 3422 |
keyidx = (key_flags >> STA_KEY_FLG_KEYID_POS) & 0x3; |
| 3423 |
|
| 3424 |
D_WEP("Remove dynamic key: idx=%d sta=%d\n", keyconf->keyidx, sta_id); |
| 3425 |
|
| 3426 |
if (keyconf->keyidx != keyidx) { |
| 3427 |
/* We need to remove a key with idx different that the one |
| 3428 |
* in the uCode. This means that the key we need to remove has |
| 3429 |
* been replaced by another one with different idx. |
| 3430 |
* Don't do anything and return ok |
| 3431 |
*/ |
| 3432 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3433 |
return 0; |
| 3434 |
} |
| 3435 |
|
| 3436 |
if (il->stations[sta_id].sta.key.key_flags & STA_KEY_FLG_INVALID) { |
| 3437 |
IL_WARN("Removing wrong key %d 0x%x\n", keyconf->keyidx, |
| 3438 |
key_flags); |
| 3439 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3440 |
return 0; |
| 3441 |
} |
| 3442 |
|
| 3443 |
if (!test_and_clear_bit |
| 3444 |
(il->stations[sta_id].sta.key.key_offset, &il->ucode_key_table)) |
| 3445 |
IL_ERR("idx %d not used in uCode key table.\n", |
| 3446 |
il->stations[sta_id].sta.key.key_offset); |
| 3447 |
memset(&il->stations[sta_id].keyinfo, 0, sizeof(struct il_hw_key)); |
| 3448 |
memset(&il->stations[sta_id].sta.key, 0, sizeof(struct il4965_keyinfo)); |
| 3449 |
il->stations[sta_id].sta.key.key_flags = |
| 3450 |
STA_KEY_FLG_NO_ENC | STA_KEY_FLG_INVALID; |
| 3451 |
il->stations[sta_id].sta.key.key_offset = keyconf->hw_key_idx; |
| 3452 |
il->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_KEY_MASK; |
| 3453 |
il->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; |
| 3454 |
|
| 3455 |
if (il_is_rfkill(il)) { |
| 3456 |
D_WEP |
| 3457 |
("Not sending C_ADD_STA command because RFKILL enabled.\n"); |
| 3458 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3459 |
return 0; |
| 3460 |
} |
| 3461 |
memcpy(&sta_cmd, &il->stations[sta_id].sta, |
| 3462 |
sizeof(struct il_addsta_cmd)); |
| 3463 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3464 |
|
| 3465 |
return il_send_add_sta(il, &sta_cmd, CMD_SYNC); |
| 3466 |
} |
| 3467 |
|
| 3468 |
int |
| 3469 |
il4965_set_dynamic_key(struct il_priv *il, struct ieee80211_key_conf *keyconf, |
| 3470 |
u8 sta_id) |
| 3471 |
{ |
| 3472 |
int ret; |
| 3473 |
|
| 3474 |
lockdep_assert_held(&il->mutex); |
| 3475 |
|
| 3476 |
il->_4965.key_mapping_keys++; |
| 3477 |
keyconf->hw_key_idx = HW_KEY_DYNAMIC; |
| 3478 |
|
| 3479 |
switch (keyconf->cipher) { |
| 3480 |
case WLAN_CIPHER_SUITE_CCMP: |
| 3481 |
ret = |
| 3482 |
il4965_set_ccmp_dynamic_key_info(il, keyconf, sta_id); |
| 3483 |
break; |
| 3484 |
case WLAN_CIPHER_SUITE_TKIP: |
| 3485 |
ret = |
| 3486 |
il4965_set_tkip_dynamic_key_info(il, keyconf, sta_id); |
| 3487 |
break; |
| 3488 |
case WLAN_CIPHER_SUITE_WEP40: |
| 3489 |
case WLAN_CIPHER_SUITE_WEP104: |
| 3490 |
ret = il4965_set_wep_dynamic_key_info(il, keyconf, sta_id); |
| 3491 |
break; |
| 3492 |
default: |
| 3493 |
IL_ERR("Unknown alg: %s cipher = %x\n", __func__, |
| 3494 |
keyconf->cipher); |
| 3495 |
ret = -EINVAL; |
| 3496 |
} |
| 3497 |
|
| 3498 |
D_WEP("Set dynamic key: cipher=%x len=%d idx=%d sta=%d ret=%d\n", |
| 3499 |
keyconf->cipher, keyconf->keylen, keyconf->keyidx, sta_id, ret); |
| 3500 |
|
| 3501 |
return ret; |
| 3502 |
} |
| 3503 |
|
| 3504 |
/* |
| 3505 |
* il4965_alloc_bcast_station - add broadcast station into driver's station table. |
| 3506 |
* |
| 3507 |
* This adds the broadcast station into the driver's station table |
| 3508 |
* and marks it driver active, so that it will be restored to the |
| 3509 |
* device at the next best time. |
| 3510 |
*/ |
| 3511 |
int |
| 3512 |
il4965_alloc_bcast_station(struct il_priv *il) |
| 3513 |
{ |
| 3514 |
struct il_link_quality_cmd *link_cmd; |
| 3515 |
unsigned long flags; |
| 3516 |
u8 sta_id; |
| 3517 |
|
| 3518 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3519 |
sta_id = il_prep_station(il, il_bcast_addr, false, NULL); |
| 3520 |
if (sta_id == IL_INVALID_STATION) { |
| 3521 |
IL_ERR("Unable to prepare broadcast station\n"); |
| 3522 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3523 |
|
| 3524 |
return -EINVAL; |
| 3525 |
} |
| 3526 |
|
| 3527 |
il->stations[sta_id].used |= IL_STA_DRIVER_ACTIVE; |
| 3528 |
il->stations[sta_id].used |= IL_STA_BCAST; |
| 3529 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3530 |
|
| 3531 |
link_cmd = il4965_sta_alloc_lq(il, sta_id); |
| 3532 |
if (!link_cmd) { |
| 3533 |
IL_ERR |
| 3534 |
("Unable to initialize rate scaling for bcast station.\n"); |
| 3535 |
return -ENOMEM; |
| 3536 |
} |
| 3537 |
|
| 3538 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3539 |
il->stations[sta_id].lq = link_cmd; |
| 3540 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3541 |
|
| 3542 |
return 0; |
| 3543 |
} |
| 3544 |
|
| 3545 |
/* |
| 3546 |
* il4965_update_bcast_station - update broadcast station's LQ command |
| 3547 |
* |
| 3548 |
* Only used by iwl4965. Placed here to have all bcast station management |
| 3549 |
* code together. |
| 3550 |
*/ |
| 3551 |
static int |
| 3552 |
il4965_update_bcast_station(struct il_priv *il) |
| 3553 |
{ |
| 3554 |
unsigned long flags; |
| 3555 |
struct il_link_quality_cmd *link_cmd; |
| 3556 |
u8 sta_id = il->hw_params.bcast_id; |
| 3557 |
|
| 3558 |
link_cmd = il4965_sta_alloc_lq(il, sta_id); |
| 3559 |
if (!link_cmd) { |
| 3560 |
IL_ERR("Unable to initialize rate scaling for bcast sta.\n"); |
| 3561 |
return -ENOMEM; |
| 3562 |
} |
| 3563 |
|
| 3564 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3565 |
if (il->stations[sta_id].lq) |
| 3566 |
kfree(il->stations[sta_id].lq); |
| 3567 |
else |
| 3568 |
D_INFO("Bcast sta rate scaling has not been initialized.\n"); |
| 3569 |
il->stations[sta_id].lq = link_cmd; |
| 3570 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3571 |
|
| 3572 |
return 0; |
| 3573 |
} |
| 3574 |
|
| 3575 |
int |
| 3576 |
il4965_update_bcast_stations(struct il_priv *il) |
| 3577 |
{ |
| 3578 |
return il4965_update_bcast_station(il); |
| 3579 |
} |
| 3580 |
|
| 3581 |
/* |
| 3582 |
* il4965_sta_tx_modify_enable_tid - Enable Tx for this TID in station table |
| 3583 |
*/ |
| 3584 |
int |
| 3585 |
il4965_sta_tx_modify_enable_tid(struct il_priv *il, int sta_id, int tid) |
| 3586 |
{ |
| 3587 |
unsigned long flags; |
| 3588 |
struct il_addsta_cmd sta_cmd; |
| 3589 |
|
| 3590 |
lockdep_assert_held(&il->mutex); |
| 3591 |
|
| 3592 |
/* Remove "disable" flag, to enable Tx for this TID */ |
| 3593 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3594 |
il->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_TID_DISABLE_TX; |
| 3595 |
il->stations[sta_id].sta.tid_disable_tx &= cpu_to_le16(~(1 << tid)); |
| 3596 |
il->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; |
| 3597 |
memcpy(&sta_cmd, &il->stations[sta_id].sta, |
| 3598 |
sizeof(struct il_addsta_cmd)); |
| 3599 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3600 |
|
| 3601 |
return il_send_add_sta(il, &sta_cmd, CMD_SYNC); |
| 3602 |
} |
| 3603 |
|
| 3604 |
int |
| 3605 |
il4965_sta_rx_agg_start(struct il_priv *il, struct ieee80211_sta *sta, int tid, |
| 3606 |
u16 ssn) |
| 3607 |
{ |
| 3608 |
unsigned long flags; |
| 3609 |
int sta_id; |
| 3610 |
struct il_addsta_cmd sta_cmd; |
| 3611 |
|
| 3612 |
lockdep_assert_held(&il->mutex); |
| 3613 |
|
| 3614 |
sta_id = il_sta_id(sta); |
| 3615 |
if (sta_id == IL_INVALID_STATION) |
| 3616 |
return -ENXIO; |
| 3617 |
|
| 3618 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3619 |
il->stations[sta_id].sta.station_flags_msk = 0; |
| 3620 |
il->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_ADDBA_TID_MSK; |
| 3621 |
il->stations[sta_id].sta.add_immediate_ba_tid = (u8) tid; |
| 3622 |
il->stations[sta_id].sta.add_immediate_ba_ssn = cpu_to_le16(ssn); |
| 3623 |
il->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; |
| 3624 |
memcpy(&sta_cmd, &il->stations[sta_id].sta, |
| 3625 |
sizeof(struct il_addsta_cmd)); |
| 3626 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3627 |
|
| 3628 |
return il_send_add_sta(il, &sta_cmd, CMD_SYNC); |
| 3629 |
} |
| 3630 |
|
| 3631 |
int |
| 3632 |
il4965_sta_rx_agg_stop(struct il_priv *il, struct ieee80211_sta *sta, int tid) |
| 3633 |
{ |
| 3634 |
unsigned long flags; |
| 3635 |
int sta_id; |
| 3636 |
struct il_addsta_cmd sta_cmd; |
| 3637 |
|
| 3638 |
lockdep_assert_held(&il->mutex); |
| 3639 |
|
| 3640 |
sta_id = il_sta_id(sta); |
| 3641 |
if (sta_id == IL_INVALID_STATION) { |
| 3642 |
IL_ERR("Invalid station for AGG tid %d\n", tid); |
| 3643 |
return -ENXIO; |
| 3644 |
} |
| 3645 |
|
| 3646 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3647 |
il->stations[sta_id].sta.station_flags_msk = 0; |
| 3648 |
il->stations[sta_id].sta.sta.modify_mask = STA_MODIFY_DELBA_TID_MSK; |
| 3649 |
il->stations[sta_id].sta.remove_immediate_ba_tid = (u8) tid; |
| 3650 |
il->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; |
| 3651 |
memcpy(&sta_cmd, &il->stations[sta_id].sta, |
| 3652 |
sizeof(struct il_addsta_cmd)); |
| 3653 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3654 |
|
| 3655 |
return il_send_add_sta(il, &sta_cmd, CMD_SYNC); |
| 3656 |
} |
| 3657 |
|
| 3658 |
void |
| 3659 |
il4965_sta_modify_sleep_tx_count(struct il_priv *il, int sta_id, int cnt) |
| 3660 |
{ |
| 3661 |
unsigned long flags; |
| 3662 |
|
| 3663 |
spin_lock_irqsave(&il->sta_lock, flags); |
| 3664 |
il->stations[sta_id].sta.station_flags |= STA_FLG_PWR_SAVE_MSK; |
| 3665 |
il->stations[sta_id].sta.station_flags_msk = STA_FLG_PWR_SAVE_MSK; |
| 3666 |
il->stations[sta_id].sta.sta.modify_mask = |
| 3667 |
STA_MODIFY_SLEEP_TX_COUNT_MSK; |
| 3668 |
il->stations[sta_id].sta.sleep_tx_count = cpu_to_le16(cnt); |
| 3669 |
il->stations[sta_id].sta.mode = STA_CONTROL_MODIFY_MSK; |
| 3670 |
il_send_add_sta(il, &il->stations[sta_id].sta, CMD_ASYNC); |
| 3671 |
spin_unlock_irqrestore(&il->sta_lock, flags); |
| 3672 |
|
| 3673 |
} |
| 3674 |
|
| 3675 |
void |
| 3676 |
il4965_update_chain_flags(struct il_priv *il) |
| 3677 |
{ |
| 3678 |
if (il->ops->set_rxon_chain) { |
| 3679 |
il->ops->set_rxon_chain(il); |
| 3680 |
if (il->active.rx_chain != il->staging.rx_chain) |
| 3681 |
il_commit_rxon(il); |
| 3682 |
} |
| 3683 |
} |
| 3684 |
|
| 3685 |
static void |
| 3686 |
il4965_clear_free_frames(struct il_priv *il) |
| 3687 |
{ |
| 3688 |
struct list_head *element; |
| 3689 |
|
| 3690 |
D_INFO("%d frames on pre-allocated heap on clear.\n", il->frames_count); |
| 3691 |
|
| 3692 |
while (!list_empty(&il->free_frames)) { |
| 3693 |
element = il->free_frames.next; |
| 3694 |
list_del(element); |
| 3695 |
kfree(list_entry(element, struct il_frame, list)); |
| 3696 |
il->frames_count--; |
| 3697 |
} |
| 3698 |
|
| 3699 |
if (il->frames_count) { |
| 3700 |
IL_WARN("%d frames still in use. Did we lose one?\n", |
| 3701 |
il->frames_count); |
| 3702 |
il->frames_count = 0; |
| 3703 |
} |
| 3704 |
} |
| 3705 |
|
| 3706 |
static struct il_frame * |
| 3707 |
il4965_get_free_frame(struct il_priv *il) |
| 3708 |
{ |
| 3709 |
struct il_frame *frame; |
| 3710 |
struct list_head *element; |
| 3711 |
if (list_empty(&il->free_frames)) { |
| 3712 |
frame = kzalloc_obj(*frame); |
| 3713 |
if (!frame) { |
| 3714 |
IL_ERR("Could not allocate frame!\n"); |
| 3715 |
return NULL; |
| 3716 |
} |
| 3717 |
|
| 3718 |
il->frames_count++; |
| 3719 |
return frame; |
| 3720 |
} |
| 3721 |
|
| 3722 |
element = il->free_frames.next; |
| 3723 |
list_del(element); |
| 3724 |
return list_entry(element, struct il_frame, list); |
| 3725 |
} |
| 3726 |
|
| 3727 |
static void |
| 3728 |
il4965_free_frame(struct il_priv *il, struct il_frame *frame) |
| 3729 |
{ |
| 3730 |
memset(frame, 0, sizeof(*frame)); |
| 3731 |
list_add(&frame->list, &il->free_frames); |
| 3732 |
} |
| 3733 |
|
| 3734 |
static u32 |
| 3735 |
il4965_fill_beacon_frame(struct il_priv *il, struct ieee80211_hdr *hdr, |
| 3736 |
int left) |
| 3737 |
{ |
| 3738 |
lockdep_assert_held(&il->mutex); |
| 3739 |
|
| 3740 |
if (!il->beacon_skb) |
| 3741 |
return 0; |
| 3742 |
|
| 3743 |
if (il->beacon_skb->len > left) |
| 3744 |
return 0; |
| 3745 |
|
| 3746 |
memcpy(hdr, il->beacon_skb->data, il->beacon_skb->len); |
| 3747 |
|
| 3748 |
return il->beacon_skb->len; |
| 3749 |
} |
| 3750 |
|
| 3751 |
/* Parse the beacon frame to find the TIM element and set tim_idx & tim_size */ |
| 3752 |
static void |
| 3753 |
il4965_set_beacon_tim(struct il_priv *il, |
| 3754 |
struct il_tx_beacon_cmd *tx_beacon_cmd, u8 * beacon, |
| 3755 |
u32 frame_size) |
| 3756 |
{ |
| 3757 |
u16 tim_idx; |
| 3758 |
struct ieee80211_mgmt *mgmt = (struct ieee80211_mgmt *)beacon; |
| 3759 |
|
| 3760 |
/* |
| 3761 |
* The idx is relative to frame start but we start looking at the |
| 3762 |
* variable-length part of the beacon. |
| 3763 |
*/ |
| 3764 |
tim_idx = mgmt->u.beacon.variable - beacon; |
| 3765 |
|
| 3766 |
/* Parse variable-length elements of beacon to find WLAN_EID_TIM */ |
| 3767 |
while ((tim_idx < (frame_size - 2)) && |
| 3768 |
(beacon[tim_idx] != WLAN_EID_TIM)) |
| 3769 |
tim_idx += beacon[tim_idx + 1] + 2; |
| 3770 |
|
| 3771 |
/* If TIM field was found, set variables */ |
| 3772 |
if ((tim_idx < (frame_size - 1)) && (beacon[tim_idx] == WLAN_EID_TIM)) { |
| 3773 |
tx_beacon_cmd->tim_idx = cpu_to_le16(tim_idx); |
| 3774 |
tx_beacon_cmd->tim_size = beacon[tim_idx + 1]; |
| 3775 |
} else |
| 3776 |
IL_WARN("Unable to find TIM Element in beacon\n"); |
| 3777 |
} |
| 3778 |
|
| 3779 |
static unsigned int |
| 3780 |
il4965_hw_get_beacon_cmd(struct il_priv *il, struct il_frame *frame) |
| 3781 |
{ |
| 3782 |
struct il_tx_beacon_cmd *tx_beacon_cmd; |
| 3783 |
u32 frame_size; |
| 3784 |
u32 rate_flags; |
| 3785 |
u32 rate; |
| 3786 |
/* |
| 3787 |
* We have to set up the TX command, the TX Beacon command, and the |
| 3788 |
* beacon contents. |
| 3789 |
*/ |
| 3790 |
|
| 3791 |
lockdep_assert_held(&il->mutex); |
| 3792 |
|
| 3793 |
if (!il->beacon_enabled) { |
| 3794 |
IL_ERR("Trying to build beacon without beaconing enabled\n"); |
| 3795 |
return 0; |
| 3796 |
} |
| 3797 |
|
| 3798 |
/* Initialize memory */ |
| 3799 |
tx_beacon_cmd = &frame->u.beacon; |
| 3800 |
memset(tx_beacon_cmd, 0, sizeof(*tx_beacon_cmd)); |
| 3801 |
|
| 3802 |
/* Set up TX beacon contents */ |
| 3803 |
frame_size = |
| 3804 |
il4965_fill_beacon_frame(il, tx_beacon_cmd->frame, |
| 3805 |
sizeof(frame->u) - sizeof(*tx_beacon_cmd)); |
| 3806 |
if (WARN_ON_ONCE(frame_size > MAX_MPDU_SIZE)) |
| 3807 |
return 0; |
| 3808 |
if (!frame_size) |
| 3809 |
return 0; |
| 3810 |
|
| 3811 |
/* Set up TX command fields */ |
| 3812 |
tx_beacon_cmd->tx.len = cpu_to_le16((u16) frame_size); |
| 3813 |
tx_beacon_cmd->tx.sta_id = il->hw_params.bcast_id; |
| 3814 |
tx_beacon_cmd->tx.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE; |
| 3815 |
tx_beacon_cmd->tx.tx_flags = |
| 3816 |
TX_CMD_FLG_SEQ_CTL_MSK | TX_CMD_FLG_TSF_MSK | |
| 3817 |
TX_CMD_FLG_STA_RATE_MSK; |
| 3818 |
|
| 3819 |
/* Set up TX beacon command fields */ |
| 3820 |
il4965_set_beacon_tim(il, tx_beacon_cmd, (u8 *) tx_beacon_cmd->frame, |
| 3821 |
frame_size); |
| 3822 |
|
| 3823 |
/* Set up packet rate and flags */ |
| 3824 |
rate = il_get_lowest_plcp(il); |
| 3825 |
il4965_toggle_tx_ant(il, &il->mgmt_tx_ant, il->hw_params.valid_tx_ant); |
| 3826 |
rate_flags = BIT(il->mgmt_tx_ant) << RATE_MCS_ANT_POS; |
| 3827 |
if ((rate >= IL_FIRST_CCK_RATE) && (rate <= IL_LAST_CCK_RATE)) |
| 3828 |
rate_flags |= RATE_MCS_CCK_MSK; |
| 3829 |
tx_beacon_cmd->tx.rate_n_flags = cpu_to_le32(rate | rate_flags); |
| 3830 |
|
| 3831 |
return sizeof(*tx_beacon_cmd) + frame_size; |
| 3832 |
} |
| 3833 |
|
| 3834 |
int |
| 3835 |
il4965_send_beacon_cmd(struct il_priv *il) |
| 3836 |
{ |
| 3837 |
struct il_frame *frame; |
| 3838 |
unsigned int frame_size; |
| 3839 |
int rc; |
| 3840 |
|
| 3841 |
frame = il4965_get_free_frame(il); |
| 3842 |
if (!frame) { |
| 3843 |
IL_ERR("Could not obtain free frame buffer for beacon " |
| 3844 |
"command.\n"); |
| 3845 |
return -ENOMEM; |
| 3846 |
} |
| 3847 |
|
| 3848 |
frame_size = il4965_hw_get_beacon_cmd(il, frame); |
| 3849 |
if (!frame_size) { |
| 3850 |
IL_ERR("Error configuring the beacon command\n"); |
| 3851 |
il4965_free_frame(il, frame); |
| 3852 |
return -EINVAL; |
| 3853 |
} |
| 3854 |
|
| 3855 |
rc = il_send_cmd_pdu(il, C_TX_BEACON, frame_size, &frame->u.cmd[0]); |
| 3856 |
|
| 3857 |
il4965_free_frame(il, frame); |
| 3858 |
|
| 3859 |
return rc; |
| 3860 |
} |
| 3861 |
|
| 3862 |
static inline dma_addr_t |
| 3863 |
il4965_tfd_tb_get_addr(struct il_tfd *tfd, u8 idx) |
| 3864 |
{ |
| 3865 |
struct il_tfd_tb *tb = &tfd->tbs[idx]; |
| 3866 |
|
| 3867 |
dma_addr_t addr = get_unaligned_le32(&tb->lo); |
| 3868 |
if (sizeof(dma_addr_t) > sizeof(u32)) |
| 3869 |
addr |= |
| 3870 |
((dma_addr_t) (le16_to_cpu(tb->hi_n_len) & 0xF) << 16) << |
| 3871 |
16; |
| 3872 |
|
| 3873 |
return addr; |
| 3874 |
} |
| 3875 |
|
| 3876 |
static inline u16 |
| 3877 |
il4965_tfd_tb_get_len(struct il_tfd *tfd, u8 idx) |
| 3878 |
{ |
| 3879 |
struct il_tfd_tb *tb = &tfd->tbs[idx]; |
| 3880 |
|
| 3881 |
return le16_to_cpu(tb->hi_n_len) >> 4; |
| 3882 |
} |
| 3883 |
|
| 3884 |
static inline void |
| 3885 |
il4965_tfd_set_tb(struct il_tfd *tfd, u8 idx, dma_addr_t addr, u16 len) |
| 3886 |
{ |
| 3887 |
struct il_tfd_tb *tb = &tfd->tbs[idx]; |
| 3888 |
u16 hi_n_len = len << 4; |
| 3889 |
|
| 3890 |
put_unaligned_le32(addr, &tb->lo); |
| 3891 |
if (sizeof(dma_addr_t) > sizeof(u32)) |
| 3892 |
hi_n_len |= ((addr >> 16) >> 16) & 0xF; |
| 3893 |
|
| 3894 |
tb->hi_n_len = cpu_to_le16(hi_n_len); |
| 3895 |
|
| 3896 |
tfd->num_tbs = idx + 1; |
| 3897 |
} |
| 3898 |
|
| 3899 |
static inline u8 |
| 3900 |
il4965_tfd_get_num_tbs(struct il_tfd *tfd) |
| 3901 |
{ |
| 3902 |
return tfd->num_tbs & 0x1f; |
| 3903 |
} |
| 3904 |
|
| 3905 |
/* |
| 3906 |
* il4965_hw_txq_free_tfd - Free all chunks referenced by TFD [txq->q.read_ptr] |
| 3907 |
* |
| 3908 |
* Does NOT advance any TFD circular buffer read/write idxes |
| 3909 |
* Does NOT free the TFD itself (which is within circular buffer) |
| 3910 |
*/ |
| 3911 |
void |
| 3912 |
il4965_hw_txq_free_tfd(struct il_priv *il, struct il_tx_queue *txq) |
| 3913 |
{ |
| 3914 |
struct il_tfd *tfd_tmp = (struct il_tfd *)txq->tfds; |
| 3915 |
struct il_tfd *tfd; |
| 3916 |
struct pci_dev *dev = il->pci_dev; |
| 3917 |
int idx = txq->q.read_ptr; |
| 3918 |
int i; |
| 3919 |
int num_tbs; |
| 3920 |
|
| 3921 |
tfd = &tfd_tmp[idx]; |
| 3922 |
|
| 3923 |
/* Sanity check on number of chunks */ |
| 3924 |
num_tbs = il4965_tfd_get_num_tbs(tfd); |
| 3925 |
|
| 3926 |
if (num_tbs >= IL_NUM_OF_TBS) { |
| 3927 |
IL_ERR("Too many chunks: %i\n", num_tbs); |
| 3928 |
/* @todo issue fatal error, it is quite serious situation */ |
| 3929 |
return; |
| 3930 |
} |
| 3931 |
|
| 3932 |
/* Unmap tx_cmd */ |
| 3933 |
if (num_tbs) |
| 3934 |
dma_unmap_single(&dev->dev, |
| 3935 |
dma_unmap_addr(&txq->meta[idx], mapping), |
| 3936 |
dma_unmap_len(&txq->meta[idx], len), |
| 3937 |
DMA_BIDIRECTIONAL); |
| 3938 |
|
| 3939 |
/* Unmap chunks, if any. */ |
| 3940 |
for (i = 1; i < num_tbs; i++) |
| 3941 |
dma_unmap_single(&dev->dev, il4965_tfd_tb_get_addr(tfd, i), |
| 3942 |
il4965_tfd_tb_get_len(tfd, i), DMA_TO_DEVICE); |
| 3943 |
|
| 3944 |
/* free SKB */ |
| 3945 |
if (txq->skbs) { |
| 3946 |
struct sk_buff *skb = txq->skbs[txq->q.read_ptr]; |
| 3947 |
|
| 3948 |
/* can be called from irqs-disabled context */ |
| 3949 |
if (skb) { |
| 3950 |
dev_kfree_skb_any(skb); |
| 3951 |
txq->skbs[txq->q.read_ptr] = NULL; |
| 3952 |
} |
| 3953 |
} |
| 3954 |
} |
| 3955 |
|
| 3956 |
int |
| 3957 |
il4965_hw_txq_attach_buf_to_tfd(struct il_priv *il, struct il_tx_queue *txq, |
| 3958 |
dma_addr_t addr, u16 len, u8 reset, u8 pad) |
| 3959 |
{ |
| 3960 |
struct il_queue *q; |
| 3961 |
struct il_tfd *tfd, *tfd_tmp; |
| 3962 |
u32 num_tbs; |
| 3963 |
|
| 3964 |
q = &txq->q; |
| 3965 |
tfd_tmp = (struct il_tfd *)txq->tfds; |
| 3966 |
tfd = &tfd_tmp[q->write_ptr]; |
| 3967 |
|
| 3968 |
if (reset) |
| 3969 |
memset(tfd, 0, sizeof(*tfd)); |
| 3970 |
|
| 3971 |
num_tbs = il4965_tfd_get_num_tbs(tfd); |
| 3972 |
|
| 3973 |
/* Each TFD can point to a maximum 20 Tx buffers */ |
| 3974 |
if (num_tbs >= IL_NUM_OF_TBS) { |
| 3975 |
IL_ERR("Error can not send more than %d chunks\n", |
| 3976 |
IL_NUM_OF_TBS); |
| 3977 |
return -EINVAL; |
| 3978 |
} |
| 3979 |
|
| 3980 |
BUG_ON(addr & ~DMA_BIT_MASK(36)); |
| 3981 |
if (unlikely(addr & ~IL_TX_DMA_MASK)) |
| 3982 |
IL_ERR("Unaligned address = %llx\n", (unsigned long long)addr); |
| 3983 |
|
| 3984 |
il4965_tfd_set_tb(tfd, num_tbs, addr, len); |
| 3985 |
|
| 3986 |
return 0; |
| 3987 |
} |
| 3988 |
|
| 3989 |
/* |
| 3990 |
* Tell nic where to find circular buffer of Tx Frame Descriptors for |
| 3991 |
* given Tx queue, and enable the DMA channel used for that queue. |
| 3992 |
* |
| 3993 |
* 4965 supports up to 16 Tx queues in DRAM, mapped to up to 8 Tx DMA |
| 3994 |
* channels supported in hardware. |
| 3995 |
*/ |
| 3996 |
int |
| 3997 |
il4965_hw_tx_queue_init(struct il_priv *il, struct il_tx_queue *txq) |
| 3998 |
{ |
| 3999 |
int txq_id = txq->q.id; |
| 4000 |
|
| 4001 |
/* Circular buffer (TFD queue in DRAM) physical base address */ |
| 4002 |
il_wr(il, FH49_MEM_CBBC_QUEUE(txq_id), txq->q.dma_addr >> 8); |
| 4003 |
|
| 4004 |
return 0; |
| 4005 |
} |
| 4006 |
|
| 4007 |
/****************************************************************************** |
| 4008 |
* |
| 4009 |
* Generic RX handler implementations |
| 4010 |
* |
| 4011 |
******************************************************************************/ |
| 4012 |
static void |
| 4013 |
il4965_hdl_alive(struct il_priv *il, struct il_rx_buf *rxb) |
| 4014 |
{ |
| 4015 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 4016 |
struct il_alive_resp *palive; |
| 4017 |
struct delayed_work *pwork; |
| 4018 |
|
| 4019 |
palive = &pkt->u.alive_frame; |
| 4020 |
|
| 4021 |
D_INFO("Alive ucode status 0x%08X revision " "0x%01X 0x%01X\n", |
| 4022 |
palive->is_valid, palive->ver_type, palive->ver_subtype); |
| 4023 |
|
| 4024 |
if (palive->ver_subtype == INITIALIZE_SUBTYPE) { |
| 4025 |
D_INFO("Initialization Alive received.\n"); |
| 4026 |
memcpy(&il->card_alive_init, &pkt->u.raw, |
| 4027 |
sizeof(struct il_init_alive_resp)); |
| 4028 |
pwork = &il->init_alive_start; |
| 4029 |
} else { |
| 4030 |
D_INFO("Runtime Alive received.\n"); |
| 4031 |
memcpy(&il->card_alive, &pkt->u.alive_frame, |
| 4032 |
sizeof(struct il_alive_resp)); |
| 4033 |
pwork = &il->alive_start; |
| 4034 |
} |
| 4035 |
|
| 4036 |
/* We delay the ALIVE response by 5ms to |
| 4037 |
* give the HW RF Kill time to activate... */ |
| 4038 |
if (palive->is_valid == UCODE_VALID_OK) |
| 4039 |
queue_delayed_work(il->workqueue, pwork, msecs_to_jiffies(5)); |
| 4040 |
else |
| 4041 |
IL_WARN("uCode did not respond OK.\n"); |
| 4042 |
} |
| 4043 |
|
| 4044 |
/* |
| 4045 |
* il4965_bg_stats_periodic - Timer callback to queue stats |
| 4046 |
* |
| 4047 |
* This callback is provided in order to send a stats request. |
| 4048 |
* |
| 4049 |
* This timer function is continually reset to execute within |
| 4050 |
* 60 seconds since the last N_STATS was received. We need to |
| 4051 |
* ensure we receive the stats in order to update the temperature |
| 4052 |
* used for calibrating the TXPOWER. |
| 4053 |
*/ |
| 4054 |
static void |
| 4055 |
il4965_bg_stats_periodic(struct timer_list *t) |
| 4056 |
{ |
| 4057 |
struct il_priv *il = timer_container_of(il, t, stats_periodic); |
| 4058 |
|
| 4059 |
if (test_bit(S_EXIT_PENDING, &il->status)) |
| 4060 |
return; |
| 4061 |
|
| 4062 |
/* dont send host command if rf-kill is on */ |
| 4063 |
if (!il_is_ready_rf(il)) |
| 4064 |
return; |
| 4065 |
|
| 4066 |
il_send_stats_request(il, CMD_ASYNC, false); |
| 4067 |
} |
| 4068 |
|
| 4069 |
static void |
| 4070 |
il4965_hdl_beacon(struct il_priv *il, struct il_rx_buf *rxb) |
| 4071 |
{ |
| 4072 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 4073 |
struct il4965_beacon_notif *beacon = |
| 4074 |
(struct il4965_beacon_notif *)pkt->u.raw; |
| 4075 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 4076 |
u8 rate = il4965_hw_get_rate(beacon->beacon_notify_hdr.rate_n_flags); |
| 4077 |
|
| 4078 |
D_RX("beacon status %x retries %d iss %d tsf:0x%.8x%.8x rate %d\n", |
| 4079 |
le32_to_cpu(beacon->beacon_notify_hdr.u.status) & TX_STATUS_MSK, |
| 4080 |
beacon->beacon_notify_hdr.failure_frame, |
| 4081 |
le32_to_cpu(beacon->ibss_mgr_status), |
| 4082 |
le32_to_cpu(beacon->high_tsf), le32_to_cpu(beacon->low_tsf), rate); |
| 4083 |
#endif |
| 4084 |
il->ibss_manager = le32_to_cpu(beacon->ibss_mgr_status); |
| 4085 |
} |
| 4086 |
|
| 4087 |
static void |
| 4088 |
il4965_perform_ct_kill_task(struct il_priv *il) |
| 4089 |
{ |
| 4090 |
unsigned long flags; |
| 4091 |
|
| 4092 |
D_POWER("Stop all queues\n"); |
| 4093 |
|
| 4094 |
if (il->mac80211_registered) |
| 4095 |
ieee80211_stop_queues(il->hw); |
| 4096 |
|
| 4097 |
_il_wr(il, CSR_UCODE_DRV_GP1_SET, |
| 4098 |
CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT); |
| 4099 |
_il_rd(il, CSR_UCODE_DRV_GP1); |
| 4100 |
|
| 4101 |
spin_lock_irqsave(&il->reg_lock, flags); |
| 4102 |
if (likely(_il_grab_nic_access(il))) |
| 4103 |
_il_release_nic_access(il); |
| 4104 |
spin_unlock_irqrestore(&il->reg_lock, flags); |
| 4105 |
} |
| 4106 |
|
| 4107 |
/* Handle notification from uCode that card's power state is changing |
| 4108 |
* due to software, hardware, or critical temperature RFKILL */ |
| 4109 |
static void |
| 4110 |
il4965_hdl_card_state(struct il_priv *il, struct il_rx_buf *rxb) |
| 4111 |
{ |
| 4112 |
struct il_rx_pkt *pkt = rxb_addr(rxb); |
| 4113 |
u32 flags = le32_to_cpu(pkt->u.card_state_notif.flags); |
| 4114 |
unsigned long status = il->status; |
| 4115 |
|
| 4116 |
D_RF_KILL("Card state received: HW:%s SW:%s CT:%s\n", |
| 4117 |
(flags & HW_CARD_DISABLED) ? "Kill" : "On", |
| 4118 |
(flags & SW_CARD_DISABLED) ? "Kill" : "On", |
| 4119 |
(flags & CT_CARD_DISABLED) ? "Reached" : "Not reached"); |
| 4120 |
|
| 4121 |
if (flags & (SW_CARD_DISABLED | HW_CARD_DISABLED | CT_CARD_DISABLED)) { |
| 4122 |
|
| 4123 |
_il_wr(il, CSR_UCODE_DRV_GP1_SET, |
| 4124 |
CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED); |
| 4125 |
|
| 4126 |
il_wr(il, HBUS_TARG_MBX_C, HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED); |
| 4127 |
|
| 4128 |
if (!(flags & RXON_CARD_DISABLED)) { |
| 4129 |
_il_wr(il, CSR_UCODE_DRV_GP1_CLR, |
| 4130 |
CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED); |
| 4131 |
il_wr(il, HBUS_TARG_MBX_C, |
| 4132 |
HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED); |
| 4133 |
} |
| 4134 |
} |
| 4135 |
|
| 4136 |
if (flags & CT_CARD_DISABLED) |
| 4137 |
il4965_perform_ct_kill_task(il); |
| 4138 |
|
| 4139 |
if (flags & HW_CARD_DISABLED) |
| 4140 |
set_bit(S_RFKILL, &il->status); |
| 4141 |
else |
| 4142 |
clear_bit(S_RFKILL, &il->status); |
| 4143 |
|
| 4144 |
if (!(flags & RXON_CARD_DISABLED)) |
| 4145 |
il_scan_cancel(il); |
| 4146 |
|
| 4147 |
if ((test_bit(S_RFKILL, &status) != |
| 4148 |
test_bit(S_RFKILL, &il->status))) |
| 4149 |
wiphy_rfkill_set_hw_state(il->hw->wiphy, |
| 4150 |
test_bit(S_RFKILL, &il->status)); |
| 4151 |
else |
| 4152 |
wake_up(&il->wait_command_queue); |
| 4153 |
} |
| 4154 |
|
| 4155 |
/* |
| 4156 |
* il4965_setup_handlers - Initialize Rx handler callbacks |
| 4157 |
* |
| 4158 |
* Setup the RX handlers for each of the reply types sent from the uCode |
| 4159 |
* to the host. |
| 4160 |
* |
| 4161 |
* This function chains into the hardware specific files for them to setup |
| 4162 |
* any hardware specific handlers as well. |
| 4163 |
*/ |
| 4164 |
static void |
| 4165 |
il4965_setup_handlers(struct il_priv *il) |
| 4166 |
{ |
| 4167 |
il->handlers[N_ALIVE] = il4965_hdl_alive; |
| 4168 |
il->handlers[N_ERROR] = il_hdl_error; |
| 4169 |
il->handlers[N_CHANNEL_SWITCH] = il_hdl_csa; |
| 4170 |
il->handlers[N_SPECTRUM_MEASUREMENT] = il_hdl_spectrum_measurement; |
| 4171 |
il->handlers[N_PM_SLEEP] = il_hdl_pm_sleep; |
| 4172 |
il->handlers[N_PM_DEBUG_STATS] = il_hdl_pm_debug_stats; |
| 4173 |
il->handlers[N_BEACON] = il4965_hdl_beacon; |
| 4174 |
|
| 4175 |
/* |
| 4176 |
* The same handler is used for both the REPLY to a discrete |
| 4177 |
* stats request from the host as well as for the periodic |
| 4178 |
* stats notifications (after received beacons) from the uCode. |
| 4179 |
*/ |
| 4180 |
il->handlers[C_STATS] = il4965_hdl_c_stats; |
| 4181 |
il->handlers[N_STATS] = il4965_hdl_stats; |
| 4182 |
|
| 4183 |
il_setup_rx_scan_handlers(il); |
| 4184 |
|
| 4185 |
/* status change handler */ |
| 4186 |
il->handlers[N_CARD_STATE] = il4965_hdl_card_state; |
| 4187 |
|
| 4188 |
il->handlers[N_MISSED_BEACONS] = il4965_hdl_missed_beacon; |
| 4189 |
/* Rx handlers */ |
| 4190 |
il->handlers[N_RX_PHY] = il4965_hdl_rx_phy; |
| 4191 |
il->handlers[N_RX_MPDU] = il4965_hdl_rx; |
| 4192 |
il->handlers[N_RX] = il4965_hdl_rx; |
| 4193 |
/* block ack */ |
| 4194 |
il->handlers[N_COMPRESSED_BA] = il4965_hdl_compressed_ba; |
| 4195 |
/* Tx response */ |
| 4196 |
il->handlers[C_TX] = il4965_hdl_tx; |
| 4197 |
} |
| 4198 |
|
| 4199 |
/* |
| 4200 |
* il4965_rx_handle - Main entry function for receiving responses from uCode |
| 4201 |
* |
| 4202 |
* Uses the il->handlers callback function array to invoke |
| 4203 |
* the appropriate handlers, including command responses, |
| 4204 |
* frame-received notifications, and other notifications. |
| 4205 |
*/ |
| 4206 |
void |
| 4207 |
il4965_rx_handle(struct il_priv *il) |
| 4208 |
{ |
| 4209 |
struct il_rx_buf *rxb; |
| 4210 |
struct il_rx_pkt *pkt; |
| 4211 |
struct il_rx_queue *rxq = &il->rxq; |
| 4212 |
u32 r, i; |
| 4213 |
int reclaim; |
| 4214 |
unsigned long flags; |
| 4215 |
u8 fill_rx = 0; |
| 4216 |
u32 count = 8; |
| 4217 |
int total_empty; |
| 4218 |
|
| 4219 |
/* uCode's read idx (stored in shared DRAM) indicates the last Rx |
| 4220 |
* buffer that the driver may process (last buffer filled by ucode). */ |
| 4221 |
r = le16_to_cpu(rxq->rb_stts->closed_rb_num) & 0x0FFF; |
| 4222 |
i = rxq->read; |
| 4223 |
|
| 4224 |
/* Rx interrupt, but nothing sent from uCode */ |
| 4225 |
if (i == r) |
| 4226 |
D_RX("r = %d, i = %d\n", r, i); |
| 4227 |
|
| 4228 |
/* calculate total frames need to be restock after handling RX */ |
| 4229 |
total_empty = r - rxq->write_actual; |
| 4230 |
if (total_empty < 0) |
| 4231 |
total_empty += RX_QUEUE_SIZE; |
| 4232 |
|
| 4233 |
if (total_empty > (RX_QUEUE_SIZE / 2)) |
| 4234 |
fill_rx = 1; |
| 4235 |
|
| 4236 |
while (i != r) { |
| 4237 |
rxb = rxq->queue[i]; |
| 4238 |
|
| 4239 |
/* If an RXB doesn't have a Rx queue slot associated with it, |
| 4240 |
* then a bug has been introduced in the queue refilling |
| 4241 |
* routines -- catch it here */ |
| 4242 |
BUG_ON(rxb == NULL); |
| 4243 |
|
| 4244 |
rxq->queue[i] = NULL; |
| 4245 |
|
| 4246 |
dma_unmap_page(&il->pci_dev->dev, rxb->page_dma, |
| 4247 |
PAGE_SIZE << il->hw_params.rx_page_order, |
| 4248 |
DMA_FROM_DEVICE); |
| 4249 |
pkt = rxb_addr(rxb); |
| 4250 |
reclaim = il_need_reclaim(il, pkt); |
| 4251 |
|
| 4252 |
/* Based on type of command response or notification, |
| 4253 |
* handle those that need handling via function in |
| 4254 |
* handlers table. See il4965_setup_handlers() */ |
| 4255 |
if (il->handlers[pkt->hdr.cmd]) { |
| 4256 |
D_RX("r = %d, i = %d, %s, 0x%02x\n", r, i, |
| 4257 |
il_get_cmd_string(pkt->hdr.cmd), pkt->hdr.cmd); |
| 4258 |
il->isr_stats.handlers[pkt->hdr.cmd]++; |
| 4259 |
il->handlers[pkt->hdr.cmd] (il, rxb); |
| 4260 |
} else { |
| 4261 |
/* No handling needed */ |
| 4262 |
D_RX("r %d i %d No handler needed for %s, 0x%02x\n", r, |
| 4263 |
i, il_get_cmd_string(pkt->hdr.cmd), pkt->hdr.cmd); |
| 4264 |
} |
| 4265 |
|
| 4266 |
/* |
| 4267 |
* XXX: After here, we should always check rxb->page |
| 4268 |
* against NULL before touching it or its virtual |
| 4269 |
* memory (pkt). Because some handler might have |
| 4270 |
* already taken or freed the pages. |
| 4271 |
*/ |
| 4272 |
|
| 4273 |
if (reclaim) { |
| 4274 |
/* Invoke any callbacks, transfer the buffer to caller, |
| 4275 |
* and fire off the (possibly) blocking il_send_cmd() |
| 4276 |
* as we reclaim the driver command queue */ |
| 4277 |
if (rxb->page) |
| 4278 |
il_tx_cmd_complete(il, rxb); |
| 4279 |
else |
| 4280 |
IL_WARN("Claim null rxb?\n"); |
| 4281 |
} |
| 4282 |
|
| 4283 |
/* Reuse the page if possible. For notification packets and |
| 4284 |
* SKBs that fail to Rx correctly, add them back into the |
| 4285 |
* rx_free list for reuse later. */ |
| 4286 |
spin_lock_irqsave(&rxq->lock, flags); |
| 4287 |
if (rxb->page != NULL) { |
| 4288 |
rxb->page_dma = |
| 4289 |
dma_map_page(&il->pci_dev->dev, rxb->page, 0, |
| 4290 |
PAGE_SIZE << il->hw_params.rx_page_order, |
| 4291 |
DMA_FROM_DEVICE); |
| 4292 |
|
| 4293 |
if (unlikely(dma_mapping_error(&il->pci_dev->dev, |
| 4294 |
rxb->page_dma))) { |
| 4295 |
__il_free_pages(il, rxb->page); |
| 4296 |
rxb->page = NULL; |
| 4297 |
list_add_tail(&rxb->list, &rxq->rx_used); |
| 4298 |
} else { |
| 4299 |
list_add_tail(&rxb->list, &rxq->rx_free); |
| 4300 |
rxq->free_count++; |
| 4301 |
} |
| 4302 |
} else |
| 4303 |
list_add_tail(&rxb->list, &rxq->rx_used); |
| 4304 |
|
| 4305 |
spin_unlock_irqrestore(&rxq->lock, flags); |
| 4306 |
|
| 4307 |
i = (i + 1) & RX_QUEUE_MASK; |
| 4308 |
/* If there are a lot of unused frames, |
| 4309 |
* restock the Rx queue so ucode wont assert. */ |
| 4310 |
if (fill_rx) { |
| 4311 |
count++; |
| 4312 |
if (count >= 8) { |
| 4313 |
rxq->read = i; |
| 4314 |
il4965_rx_replenish_now(il); |
| 4315 |
count = 0; |
| 4316 |
} |
| 4317 |
} |
| 4318 |
} |
| 4319 |
|
| 4320 |
/* Backtrack one entry */ |
| 4321 |
rxq->read = i; |
| 4322 |
if (fill_rx) |
| 4323 |
il4965_rx_replenish_now(il); |
| 4324 |
else |
| 4325 |
il4965_rx_queue_restock(il); |
| 4326 |
} |
| 4327 |
|
| 4328 |
/* call this function to flush any scheduled tasklet */ |
| 4329 |
static inline void |
| 4330 |
il4965_synchronize_irq(struct il_priv *il) |
| 4331 |
{ |
| 4332 |
/* wait to make sure we flush pending tasklet */ |
| 4333 |
synchronize_irq(il->pci_dev->irq); |
| 4334 |
tasklet_kill(&il->irq_tasklet); |
| 4335 |
} |
| 4336 |
|
| 4337 |
static void |
| 4338 |
il4965_irq_tasklet(struct tasklet_struct *t) |
| 4339 |
{ |
| 4340 |
struct il_priv *il = from_tasklet(il, t, irq_tasklet); |
| 4341 |
u32 inta, handled = 0; |
| 4342 |
u32 inta_fh; |
| 4343 |
unsigned long flags; |
| 4344 |
u32 i; |
| 4345 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 4346 |
u32 inta_mask; |
| 4347 |
#endif |
| 4348 |
|
| 4349 |
spin_lock_irqsave(&il->lock, flags); |
| 4350 |
|
| 4351 |
/* Ack/clear/reset pending uCode interrupts. |
| 4352 |
* Note: Some bits in CSR_INT are "OR" of bits in CSR_FH_INT_STATUS, |
| 4353 |
* and will clear only when CSR_FH_INT_STATUS gets cleared. */ |
| 4354 |
inta = _il_rd(il, CSR_INT); |
| 4355 |
_il_wr(il, CSR_INT, inta); |
| 4356 |
|
| 4357 |
/* Ack/clear/reset pending flow-handler (DMA) interrupts. |
| 4358 |
* Any new interrupts that happen after this, either while we're |
| 4359 |
* in this tasklet, or later, will show up in next ISR/tasklet. */ |
| 4360 |
inta_fh = _il_rd(il, CSR_FH_INT_STATUS); |
| 4361 |
_il_wr(il, CSR_FH_INT_STATUS, inta_fh); |
| 4362 |
|
| 4363 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 4364 |
if (il_get_debug_level(il) & IL_DL_ISR) { |
| 4365 |
/* just for debug */ |
| 4366 |
inta_mask = _il_rd(il, CSR_INT_MASK); |
| 4367 |
D_ISR("inta 0x%08x, enabled 0x%08x, fh 0x%08x\n", inta, |
| 4368 |
inta_mask, inta_fh); |
| 4369 |
} |
| 4370 |
#endif |
| 4371 |
|
| 4372 |
spin_unlock_irqrestore(&il->lock, flags); |
| 4373 |
|
| 4374 |
/* Since CSR_INT and CSR_FH_INT_STATUS reads and clears are not |
| 4375 |
* atomic, make sure that inta covers all the interrupts that |
| 4376 |
* we've discovered, even if FH interrupt came in just after |
| 4377 |
* reading CSR_INT. */ |
| 4378 |
if (inta_fh & CSR49_FH_INT_RX_MASK) |
| 4379 |
inta |= CSR_INT_BIT_FH_RX; |
| 4380 |
if (inta_fh & CSR49_FH_INT_TX_MASK) |
| 4381 |
inta |= CSR_INT_BIT_FH_TX; |
| 4382 |
|
| 4383 |
/* Now service all interrupt bits discovered above. */ |
| 4384 |
if (inta & CSR_INT_BIT_HW_ERR) { |
| 4385 |
IL_ERR("Hardware error detected. Restarting.\n"); |
| 4386 |
|
| 4387 |
/* Tell the device to stop sending interrupts */ |
| 4388 |
il_disable_interrupts(il); |
| 4389 |
|
| 4390 |
il->isr_stats.hw++; |
| 4391 |
il_irq_handle_error(il); |
| 4392 |
|
| 4393 |
handled |= CSR_INT_BIT_HW_ERR; |
| 4394 |
|
| 4395 |
return; |
| 4396 |
} |
| 4397 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 4398 |
if (il_get_debug_level(il) & (IL_DL_ISR)) { |
| 4399 |
/* NIC fires this, but we don't use it, redundant with WAKEUP */ |
| 4400 |
if (inta & CSR_INT_BIT_SCD) { |
| 4401 |
D_ISR("Scheduler finished to transmit " |
| 4402 |
"the frame/frames.\n"); |
| 4403 |
il->isr_stats.sch++; |
| 4404 |
} |
| 4405 |
|
| 4406 |
/* Alive notification via Rx interrupt will do the real work */ |
| 4407 |
if (inta & CSR_INT_BIT_ALIVE) { |
| 4408 |
D_ISR("Alive interrupt\n"); |
| 4409 |
il->isr_stats.alive++; |
| 4410 |
} |
| 4411 |
} |
| 4412 |
#endif |
| 4413 |
/* Safely ignore these bits for debug checks below */ |
| 4414 |
inta &= ~(CSR_INT_BIT_SCD | CSR_INT_BIT_ALIVE); |
| 4415 |
|
| 4416 |
/* HW RF KILL switch toggled */ |
| 4417 |
if (inta & CSR_INT_BIT_RF_KILL) { |
| 4418 |
int hw_rf_kill = 0; |
| 4419 |
|
| 4420 |
if (!(_il_rd(il, CSR_GP_CNTRL) & CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW)) |
| 4421 |
hw_rf_kill = 1; |
| 4422 |
|
| 4423 |
IL_WARN("RF_KILL bit toggled to %s.\n", |
| 4424 |
hw_rf_kill ? "disable radio" : "enable radio"); |
| 4425 |
|
| 4426 |
il->isr_stats.rfkill++; |
| 4427 |
|
| 4428 |
/* driver only loads ucode once setting the interface up. |
| 4429 |
* the driver allows loading the ucode even if the radio |
| 4430 |
* is killed. Hence update the killswitch state here. The |
| 4431 |
* rfkill handler will care about restarting if needed. |
| 4432 |
*/ |
| 4433 |
if (hw_rf_kill) { |
| 4434 |
set_bit(S_RFKILL, &il->status); |
| 4435 |
} else { |
| 4436 |
clear_bit(S_RFKILL, &il->status); |
| 4437 |
il_force_reset(il, true); |
| 4438 |
} |
| 4439 |
wiphy_rfkill_set_hw_state(il->hw->wiphy, hw_rf_kill); |
| 4440 |
|
| 4441 |
handled |= CSR_INT_BIT_RF_KILL; |
| 4442 |
} |
| 4443 |
|
| 4444 |
/* Chip got too hot and stopped itself */ |
| 4445 |
if (inta & CSR_INT_BIT_CT_KILL) { |
| 4446 |
IL_ERR("Microcode CT kill error detected.\n"); |
| 4447 |
il->isr_stats.ctkill++; |
| 4448 |
handled |= CSR_INT_BIT_CT_KILL; |
| 4449 |
} |
| 4450 |
|
| 4451 |
/* Error detected by uCode */ |
| 4452 |
if (inta & CSR_INT_BIT_SW_ERR) { |
| 4453 |
IL_ERR("Microcode SW error detected. " " Restarting 0x%X.\n", |
| 4454 |
inta); |
| 4455 |
il->isr_stats.sw++; |
| 4456 |
il_irq_handle_error(il); |
| 4457 |
handled |= CSR_INT_BIT_SW_ERR; |
| 4458 |
} |
| 4459 |
|
| 4460 |
/* |
| 4461 |
* uCode wakes up after power-down sleep. |
| 4462 |
* Tell device about any new tx or host commands enqueued, |
| 4463 |
* and about any Rx buffers made available while asleep. |
| 4464 |
*/ |
| 4465 |
if (inta & CSR_INT_BIT_WAKEUP) { |
| 4466 |
D_ISR("Wakeup interrupt\n"); |
| 4467 |
il_rx_queue_update_write_ptr(il, &il->rxq); |
| 4468 |
for (i = 0; i < il->hw_params.max_txq_num; i++) |
| 4469 |
il_txq_update_write_ptr(il, &il->txq[i]); |
| 4470 |
il->isr_stats.wakeup++; |
| 4471 |
handled |= CSR_INT_BIT_WAKEUP; |
| 4472 |
} |
| 4473 |
|
| 4474 |
/* All uCode command responses, including Tx command responses, |
| 4475 |
* Rx "responses" (frame-received notification), and other |
| 4476 |
* notifications from uCode come through here*/ |
| 4477 |
if (inta & (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX)) { |
| 4478 |
il4965_rx_handle(il); |
| 4479 |
il->isr_stats.rx++; |
| 4480 |
handled |= (CSR_INT_BIT_FH_RX | CSR_INT_BIT_SW_RX); |
| 4481 |
} |
| 4482 |
|
| 4483 |
/* This "Tx" DMA channel is used only for loading uCode */ |
| 4484 |
if (inta & CSR_INT_BIT_FH_TX) { |
| 4485 |
D_ISR("uCode load interrupt\n"); |
| 4486 |
il->isr_stats.tx++; |
| 4487 |
handled |= CSR_INT_BIT_FH_TX; |
| 4488 |
/* Wake up uCode load routine, now that load is complete */ |
| 4489 |
il->ucode_write_complete = 1; |
| 4490 |
wake_up(&il->wait_command_queue); |
| 4491 |
} |
| 4492 |
|
| 4493 |
if (inta & ~handled) { |
| 4494 |
IL_ERR("Unhandled INTA bits 0x%08x\n", inta & ~handled); |
| 4495 |
il->isr_stats.unhandled++; |
| 4496 |
} |
| 4497 |
|
| 4498 |
if (inta & ~(il->inta_mask)) { |
| 4499 |
IL_WARN("Disabled INTA bits 0x%08x were pending\n", |
| 4500 |
inta & ~il->inta_mask); |
| 4501 |
IL_WARN(" with FH49_INT = 0x%08x\n", inta_fh); |
| 4502 |
} |
| 4503 |
|
| 4504 |
/* Re-enable all interrupts */ |
| 4505 |
/* only Re-enable if disabled by irq */ |
| 4506 |
if (test_bit(S_INT_ENABLED, &il->status)) |
| 4507 |
il_enable_interrupts(il); |
| 4508 |
/* Re-enable RF_KILL if it occurred */ |
| 4509 |
else if (handled & CSR_INT_BIT_RF_KILL) |
| 4510 |
il_enable_rfkill_int(il); |
| 4511 |
|
| 4512 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 4513 |
if (il_get_debug_level(il) & (IL_DL_ISR)) { |
| 4514 |
inta = _il_rd(il, CSR_INT); |
| 4515 |
inta_mask = _il_rd(il, CSR_INT_MASK); |
| 4516 |
inta_fh = _il_rd(il, CSR_FH_INT_STATUS); |
| 4517 |
D_ISR("End inta 0x%08x, enabled 0x%08x, fh 0x%08x, " |
| 4518 |
"flags 0x%08lx\n", inta, inta_mask, inta_fh, flags); |
| 4519 |
} |
| 4520 |
#endif |
| 4521 |
} |
| 4522 |
|
| 4523 |
/***************************************************************************** |
| 4524 |
* |
| 4525 |
* sysfs attributes |
| 4526 |
* |
| 4527 |
*****************************************************************************/ |
| 4528 |
|
| 4529 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 4530 |
|
| 4531 |
/* |
| 4532 |
* The following adds a new attribute to the sysfs representation |
| 4533 |
* of this device driver (i.e. a new file in /sys/class/net/wlan0/device/) |
| 4534 |
* used for controlling the debug level. |
| 4535 |
* |
| 4536 |
* See the level definitions in iwl for details. |
| 4537 |
* |
| 4538 |
* The debug_level being managed using sysfs below is a per device debug |
| 4539 |
* level that is used instead of the global debug level if it (the per |
| 4540 |
* device debug level) is set. |
| 4541 |
*/ |
| 4542 |
static ssize_t |
| 4543 |
il4965_show_debug_level(struct device *d, struct device_attribute *attr, |
| 4544 |
char *buf) |
| 4545 |
{ |
| 4546 |
struct il_priv *il = dev_get_drvdata(d); |
| 4547 |
return sprintf(buf, "0x%08X\n", il_get_debug_level(il)); |
| 4548 |
} |
| 4549 |
|
| 4550 |
static ssize_t |
| 4551 |
il4965_store_debug_level(struct device *d, struct device_attribute *attr, |
| 4552 |
const char *buf, size_t count) |
| 4553 |
{ |
| 4554 |
struct il_priv *il = dev_get_drvdata(d); |
| 4555 |
unsigned long val; |
| 4556 |
int ret; |
| 4557 |
|
| 4558 |
ret = kstrtoul(buf, 0, &val); |
| 4559 |
if (ret) |
| 4560 |
IL_ERR("%s is not in hex or decimal form.\n", buf); |
| 4561 |
else |
| 4562 |
il->debug_level = val; |
| 4563 |
|
| 4564 |
return strnlen(buf, count); |
| 4565 |
} |
| 4566 |
|
| 4567 |
static DEVICE_ATTR(debug_level, 0644, il4965_show_debug_level, |
| 4568 |
il4965_store_debug_level); |
| 4569 |
|
| 4570 |
#endif /* CONFIG_IWLEGACY_DEBUG */ |
| 4571 |
|
| 4572 |
static ssize_t |
| 4573 |
il4965_show_temperature(struct device *d, struct device_attribute *attr, |
| 4574 |
char *buf) |
| 4575 |
{ |
| 4576 |
struct il_priv *il = dev_get_drvdata(d); |
| 4577 |
|
| 4578 |
if (!il_is_alive(il)) |
| 4579 |
return -EAGAIN; |
| 4580 |
|
| 4581 |
return sprintf(buf, "%d\n", il->temperature); |
| 4582 |
} |
| 4583 |
|
| 4584 |
static DEVICE_ATTR(temperature, 0444, il4965_show_temperature, NULL); |
| 4585 |
|
| 4586 |
static ssize_t |
| 4587 |
il4965_show_tx_power(struct device *d, struct device_attribute *attr, char *buf) |
| 4588 |
{ |
| 4589 |
struct il_priv *il = dev_get_drvdata(d); |
| 4590 |
|
| 4591 |
if (!il_is_ready_rf(il)) |
| 4592 |
return sprintf(buf, "off\n"); |
| 4593 |
else |
| 4594 |
return sprintf(buf, "%d\n", il->tx_power_user_lmt); |
| 4595 |
} |
| 4596 |
|
| 4597 |
static ssize_t |
| 4598 |
il4965_store_tx_power(struct device *d, struct device_attribute *attr, |
| 4599 |
const char *buf, size_t count) |
| 4600 |
{ |
| 4601 |
struct il_priv *il = dev_get_drvdata(d); |
| 4602 |
unsigned long val; |
| 4603 |
int ret; |
| 4604 |
|
| 4605 |
ret = kstrtoul(buf, 10, &val); |
| 4606 |
if (ret) |
| 4607 |
IL_INFO("%s is not in decimal form.\n", buf); |
| 4608 |
else { |
| 4609 |
mutex_lock(&il->mutex); |
| 4610 |
ret = il_set_tx_power(il, val, false); |
| 4611 |
mutex_unlock(&il->mutex); |
| 4612 |
if (ret) |
| 4613 |
IL_ERR("failed setting tx power (0x%08x).\n", ret); |
| 4614 |
else |
| 4615 |
ret = count; |
| 4616 |
} |
| 4617 |
return ret; |
| 4618 |
} |
| 4619 |
|
| 4620 |
static DEVICE_ATTR(tx_power, 0644, il4965_show_tx_power, |
| 4621 |
il4965_store_tx_power); |
| 4622 |
|
| 4623 |
static struct attribute *il_sysfs_entries[] = { |
| 4624 |
&dev_attr_temperature.attr, |
| 4625 |
&dev_attr_tx_power.attr, |
| 4626 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 4627 |
&dev_attr_debug_level.attr, |
| 4628 |
#endif |
| 4629 |
NULL |
| 4630 |
}; |
| 4631 |
|
| 4632 |
static const struct attribute_group il_attribute_group = { |
| 4633 |
.name = NULL, /* put in device directory */ |
| 4634 |
.attrs = il_sysfs_entries, |
| 4635 |
}; |
| 4636 |
|
| 4637 |
/****************************************************************************** |
| 4638 |
* |
| 4639 |
* uCode download functions |
| 4640 |
* |
| 4641 |
******************************************************************************/ |
| 4642 |
|
| 4643 |
static void |
| 4644 |
il4965_dealloc_ucode_pci(struct il_priv *il) |
| 4645 |
{ |
| 4646 |
il_free_fw_desc(il->pci_dev, &il->ucode_code); |
| 4647 |
il_free_fw_desc(il->pci_dev, &il->ucode_data); |
| 4648 |
il_free_fw_desc(il->pci_dev, &il->ucode_data_backup); |
| 4649 |
il_free_fw_desc(il->pci_dev, &il->ucode_init); |
| 4650 |
il_free_fw_desc(il->pci_dev, &il->ucode_init_data); |
| 4651 |
il_free_fw_desc(il->pci_dev, &il->ucode_boot); |
| 4652 |
} |
| 4653 |
|
| 4654 |
static void |
| 4655 |
il4965_nic_start(struct il_priv *il) |
| 4656 |
{ |
| 4657 |
/* Remove all resets to allow NIC to operate */ |
| 4658 |
_il_wr(il, CSR_RESET, 0); |
| 4659 |
} |
| 4660 |
|
| 4661 |
static void il4965_ucode_callback(const struct firmware *ucode_raw, |
| 4662 |
void *context); |
| 4663 |
static int il4965_mac_setup_register(struct il_priv *il, u32 max_probe_length); |
| 4664 |
|
| 4665 |
static int __must_check |
| 4666 |
il4965_request_firmware(struct il_priv *il, bool first) |
| 4667 |
{ |
| 4668 |
const char *name_pre = il->cfg->fw_name_pre; |
| 4669 |
char tag[8]; |
| 4670 |
|
| 4671 |
if (first) { |
| 4672 |
il->fw_idx = il->cfg->ucode_api_max; |
| 4673 |
sprintf(tag, "%d", il->fw_idx); |
| 4674 |
} else { |
| 4675 |
il->fw_idx--; |
| 4676 |
sprintf(tag, "%d", il->fw_idx); |
| 4677 |
} |
| 4678 |
|
| 4679 |
if (il->fw_idx < il->cfg->ucode_api_min) { |
| 4680 |
IL_ERR("no suitable firmware found!\n"); |
| 4681 |
return -ENOENT; |
| 4682 |
} |
| 4683 |
|
| 4684 |
sprintf(il->firmware_name, "%s%s%s", name_pre, tag, ".ucode"); |
| 4685 |
|
| 4686 |
D_INFO("attempting to load firmware '%s'\n", il->firmware_name); |
| 4687 |
|
| 4688 |
return request_firmware_nowait(THIS_MODULE, 1, il->firmware_name, |
| 4689 |
&il->pci_dev->dev, GFP_KERNEL, il, |
| 4690 |
il4965_ucode_callback); |
| 4691 |
} |
| 4692 |
|
| 4693 |
struct il4965_firmware_pieces { |
| 4694 |
const void *inst, *data, *init, *init_data, *boot; |
| 4695 |
size_t inst_size, data_size, init_size, init_data_size, boot_size; |
| 4696 |
}; |
| 4697 |
|
| 4698 |
static int |
| 4699 |
il4965_load_firmware(struct il_priv *il, const struct firmware *ucode_raw, |
| 4700 |
struct il4965_firmware_pieces *pieces) |
| 4701 |
{ |
| 4702 |
struct il_ucode_header *ucode = (void *)ucode_raw->data; |
| 4703 |
u32 api_ver, hdr_size; |
| 4704 |
const u8 *src; |
| 4705 |
|
| 4706 |
il->ucode_ver = le32_to_cpu(ucode->ver); |
| 4707 |
api_ver = IL_UCODE_API(il->ucode_ver); |
| 4708 |
|
| 4709 |
switch (api_ver) { |
| 4710 |
default: |
| 4711 |
case 0: |
| 4712 |
case 1: |
| 4713 |
case 2: |
| 4714 |
hdr_size = 24; |
| 4715 |
if (ucode_raw->size < hdr_size) { |
| 4716 |
IL_ERR("File size too small!\n"); |
| 4717 |
return -EINVAL; |
| 4718 |
} |
| 4719 |
pieces->inst_size = le32_to_cpu(ucode->v1.inst_size); |
| 4720 |
pieces->data_size = le32_to_cpu(ucode->v1.data_size); |
| 4721 |
pieces->init_size = le32_to_cpu(ucode->v1.init_size); |
| 4722 |
pieces->init_data_size = le32_to_cpu(ucode->v1.init_data_size); |
| 4723 |
pieces->boot_size = le32_to_cpu(ucode->v1.boot_size); |
| 4724 |
src = ucode->v1.data; |
| 4725 |
break; |
| 4726 |
} |
| 4727 |
|
| 4728 |
/* Verify size of file vs. image size info in file's header */ |
| 4729 |
if (ucode_raw->size != |
| 4730 |
hdr_size + pieces->inst_size + pieces->data_size + |
| 4731 |
pieces->init_size + pieces->init_data_size + pieces->boot_size) { |
| 4732 |
|
| 4733 |
IL_ERR("uCode file size %d does not match expected size\n", |
| 4734 |
(int)ucode_raw->size); |
| 4735 |
return -EINVAL; |
| 4736 |
} |
| 4737 |
|
| 4738 |
pieces->inst = src; |
| 4739 |
src += pieces->inst_size; |
| 4740 |
pieces->data = src; |
| 4741 |
src += pieces->data_size; |
| 4742 |
pieces->init = src; |
| 4743 |
src += pieces->init_size; |
| 4744 |
pieces->init_data = src; |
| 4745 |
src += pieces->init_data_size; |
| 4746 |
pieces->boot = src; |
| 4747 |
src += pieces->boot_size; |
| 4748 |
|
| 4749 |
return 0; |
| 4750 |
} |
| 4751 |
|
| 4752 |
/* |
| 4753 |
* il4965_ucode_callback - callback when firmware was loaded |
| 4754 |
* |
| 4755 |
* If loaded successfully, copies the firmware into buffers |
| 4756 |
* for the card to fetch (via DMA). |
| 4757 |
*/ |
| 4758 |
static void |
| 4759 |
il4965_ucode_callback(const struct firmware *ucode_raw, void *context) |
| 4760 |
{ |
| 4761 |
struct il_priv *il = context; |
| 4762 |
int err; |
| 4763 |
struct il4965_firmware_pieces pieces; |
| 4764 |
const unsigned int api_max = il->cfg->ucode_api_max; |
| 4765 |
const unsigned int api_min = il->cfg->ucode_api_min; |
| 4766 |
u32 api_ver; |
| 4767 |
|
| 4768 |
u32 max_probe_length = 200; |
| 4769 |
u32 standard_phy_calibration_size = |
| 4770 |
IL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE; |
| 4771 |
|
| 4772 |
memset(&pieces, 0, sizeof(pieces)); |
| 4773 |
|
| 4774 |
if (!ucode_raw) { |
| 4775 |
if (il->fw_idx <= il->cfg->ucode_api_max) |
| 4776 |
IL_ERR("request for firmware file '%s' failed.\n", |
| 4777 |
il->firmware_name); |
| 4778 |
goto try_again; |
| 4779 |
} |
| 4780 |
|
| 4781 |
D_INFO("Loaded firmware file '%s' (%zd bytes).\n", il->firmware_name, |
| 4782 |
ucode_raw->size); |
| 4783 |
|
| 4784 |
/* Make sure that we got at least the API version number */ |
| 4785 |
if (ucode_raw->size < 4) { |
| 4786 |
IL_ERR("File size way too small!\n"); |
| 4787 |
goto try_again; |
| 4788 |
} |
| 4789 |
|
| 4790 |
/* Data from ucode file: header followed by uCode images */ |
| 4791 |
err = il4965_load_firmware(il, ucode_raw, &pieces); |
| 4792 |
|
| 4793 |
if (err) |
| 4794 |
goto try_again; |
| 4795 |
|
| 4796 |
api_ver = IL_UCODE_API(il->ucode_ver); |
| 4797 |
|
| 4798 |
/* |
| 4799 |
* api_ver should match the api version forming part of the |
| 4800 |
* firmware filename ... but we don't check for that and only rely |
| 4801 |
* on the API version read from firmware header from here on forward |
| 4802 |
*/ |
| 4803 |
if (api_ver < api_min || api_ver > api_max) { |
| 4804 |
IL_ERR("Driver unable to support your firmware API. " |
| 4805 |
"Driver supports v%u, firmware is v%u.\n", api_max, |
| 4806 |
api_ver); |
| 4807 |
goto try_again; |
| 4808 |
} |
| 4809 |
|
| 4810 |
if (api_ver != api_max) |
| 4811 |
IL_ERR("Firmware has old API version. Expected v%u, " |
| 4812 |
"got v%u. New firmware can be obtained " |
| 4813 |
"from http://www.intellinuxwireless.org.\n", api_max, |
| 4814 |
api_ver); |
| 4815 |
|
| 4816 |
IL_INFO("loaded firmware version %u.%u.%u.%u\n", |
| 4817 |
IL_UCODE_MAJOR(il->ucode_ver), IL_UCODE_MINOR(il->ucode_ver), |
| 4818 |
IL_UCODE_API(il->ucode_ver), IL_UCODE_SERIAL(il->ucode_ver)); |
| 4819 |
|
| 4820 |
snprintf(il->hw->wiphy->fw_version, sizeof(il->hw->wiphy->fw_version), |
| 4821 |
"%u.%u.%u.%u", IL_UCODE_MAJOR(il->ucode_ver), |
| 4822 |
IL_UCODE_MINOR(il->ucode_ver), IL_UCODE_API(il->ucode_ver), |
| 4823 |
IL_UCODE_SERIAL(il->ucode_ver)); |
| 4824 |
|
| 4825 |
/* |
| 4826 |
* For any of the failures below (before allocating pci memory) |
| 4827 |
* we will try to load a version with a smaller API -- maybe the |
| 4828 |
* user just got a corrupted version of the latest API. |
| 4829 |
*/ |
| 4830 |
|
| 4831 |
D_INFO("f/w package hdr ucode version raw = 0x%x\n", il->ucode_ver); |
| 4832 |
D_INFO("f/w package hdr runtime inst size = %zd\n", pieces.inst_size); |
| 4833 |
D_INFO("f/w package hdr runtime data size = %zd\n", pieces.data_size); |
| 4834 |
D_INFO("f/w package hdr init inst size = %zd\n", pieces.init_size); |
| 4835 |
D_INFO("f/w package hdr init data size = %zd\n", pieces.init_data_size); |
| 4836 |
D_INFO("f/w package hdr boot inst size = %zd\n", pieces.boot_size); |
| 4837 |
|
| 4838 |
/* Verify that uCode images will fit in card's SRAM */ |
| 4839 |
if (pieces.inst_size > il->hw_params.max_inst_size) { |
| 4840 |
IL_ERR("uCode instr len %zd too large to fit in\n", |
| 4841 |
pieces.inst_size); |
| 4842 |
goto try_again; |
| 4843 |
} |
| 4844 |
|
| 4845 |
if (pieces.data_size > il->hw_params.max_data_size) { |
| 4846 |
IL_ERR("uCode data len %zd too large to fit in\n", |
| 4847 |
pieces.data_size); |
| 4848 |
goto try_again; |
| 4849 |
} |
| 4850 |
|
| 4851 |
if (pieces.init_size > il->hw_params.max_inst_size) { |
| 4852 |
IL_ERR("uCode init instr len %zd too large to fit in\n", |
| 4853 |
pieces.init_size); |
| 4854 |
goto try_again; |
| 4855 |
} |
| 4856 |
|
| 4857 |
if (pieces.init_data_size > il->hw_params.max_data_size) { |
| 4858 |
IL_ERR("uCode init data len %zd too large to fit in\n", |
| 4859 |
pieces.init_data_size); |
| 4860 |
goto try_again; |
| 4861 |
} |
| 4862 |
|
| 4863 |
if (pieces.boot_size > il->hw_params.max_bsm_size) { |
| 4864 |
IL_ERR("uCode boot instr len %zd too large to fit in\n", |
| 4865 |
pieces.boot_size); |
| 4866 |
goto try_again; |
| 4867 |
} |
| 4868 |
|
| 4869 |
/* Allocate ucode buffers for card's bus-master loading ... */ |
| 4870 |
|
| 4871 |
/* Runtime instructions and 2 copies of data: |
| 4872 |
* 1) unmodified from disk |
| 4873 |
* 2) backup cache for save/restore during power-downs */ |
| 4874 |
il->ucode_code.len = pieces.inst_size; |
| 4875 |
il_alloc_fw_desc(il->pci_dev, &il->ucode_code); |
| 4876 |
|
| 4877 |
il->ucode_data.len = pieces.data_size; |
| 4878 |
il_alloc_fw_desc(il->pci_dev, &il->ucode_data); |
| 4879 |
|
| 4880 |
il->ucode_data_backup.len = pieces.data_size; |
| 4881 |
il_alloc_fw_desc(il->pci_dev, &il->ucode_data_backup); |
| 4882 |
|
| 4883 |
if (!il->ucode_code.v_addr || !il->ucode_data.v_addr || |
| 4884 |
!il->ucode_data_backup.v_addr) |
| 4885 |
goto err_pci_alloc; |
| 4886 |
|
| 4887 |
/* Initialization instructions and data */ |
| 4888 |
if (pieces.init_size && pieces.init_data_size) { |
| 4889 |
il->ucode_init.len = pieces.init_size; |
| 4890 |
il_alloc_fw_desc(il->pci_dev, &il->ucode_init); |
| 4891 |
|
| 4892 |
il->ucode_init_data.len = pieces.init_data_size; |
| 4893 |
il_alloc_fw_desc(il->pci_dev, &il->ucode_init_data); |
| 4894 |
|
| 4895 |
if (!il->ucode_init.v_addr || !il->ucode_init_data.v_addr) |
| 4896 |
goto err_pci_alloc; |
| 4897 |
} |
| 4898 |
|
| 4899 |
/* Bootstrap (instructions only, no data) */ |
| 4900 |
if (pieces.boot_size) { |
| 4901 |
il->ucode_boot.len = pieces.boot_size; |
| 4902 |
il_alloc_fw_desc(il->pci_dev, &il->ucode_boot); |
| 4903 |
|
| 4904 |
if (!il->ucode_boot.v_addr) |
| 4905 |
goto err_pci_alloc; |
| 4906 |
} |
| 4907 |
|
| 4908 |
/* Now that we can no longer fail, copy information */ |
| 4909 |
|
| 4910 |
il->sta_key_max_num = STA_KEY_MAX_NUM; |
| 4911 |
|
| 4912 |
/* Copy images into buffers for card's bus-master reads ... */ |
| 4913 |
|
| 4914 |
/* Runtime instructions (first block of data in file) */ |
| 4915 |
D_INFO("Copying (but not loading) uCode instr len %zd\n", |
| 4916 |
pieces.inst_size); |
| 4917 |
memcpy(il->ucode_code.v_addr, pieces.inst, pieces.inst_size); |
| 4918 |
|
| 4919 |
D_INFO("uCode instr buf vaddr = 0x%p, paddr = 0x%08x\n", |
| 4920 |
il->ucode_code.v_addr, (u32) il->ucode_code.p_addr); |
| 4921 |
|
| 4922 |
/* |
| 4923 |
* Runtime data |
| 4924 |
* NOTE: Copy into backup buffer will be done in il_up() |
| 4925 |
*/ |
| 4926 |
D_INFO("Copying (but not loading) uCode data len %zd\n", |
| 4927 |
pieces.data_size); |
| 4928 |
memcpy(il->ucode_data.v_addr, pieces.data, pieces.data_size); |
| 4929 |
memcpy(il->ucode_data_backup.v_addr, pieces.data, pieces.data_size); |
| 4930 |
|
| 4931 |
/* Initialization instructions */ |
| 4932 |
if (pieces.init_size) { |
| 4933 |
D_INFO("Copying (but not loading) init instr len %zd\n", |
| 4934 |
pieces.init_size); |
| 4935 |
memcpy(il->ucode_init.v_addr, pieces.init, pieces.init_size); |
| 4936 |
} |
| 4937 |
|
| 4938 |
/* Initialization data */ |
| 4939 |
if (pieces.init_data_size) { |
| 4940 |
D_INFO("Copying (but not loading) init data len %zd\n", |
| 4941 |
pieces.init_data_size); |
| 4942 |
memcpy(il->ucode_init_data.v_addr, pieces.init_data, |
| 4943 |
pieces.init_data_size); |
| 4944 |
} |
| 4945 |
|
| 4946 |
/* Bootstrap instructions */ |
| 4947 |
D_INFO("Copying (but not loading) boot instr len %zd\n", |
| 4948 |
pieces.boot_size); |
| 4949 |
memcpy(il->ucode_boot.v_addr, pieces.boot, pieces.boot_size); |
| 4950 |
|
| 4951 |
/* |
| 4952 |
* figure out the offset of chain noise reset and gain commands |
| 4953 |
* base on the size of standard phy calibration commands table size |
| 4954 |
*/ |
| 4955 |
il->_4965.phy_calib_chain_noise_reset_cmd = |
| 4956 |
standard_phy_calibration_size; |
| 4957 |
il->_4965.phy_calib_chain_noise_gain_cmd = |
| 4958 |
standard_phy_calibration_size + 1; |
| 4959 |
|
| 4960 |
/************************************************** |
| 4961 |
* This is still part of probe() in a sense... |
| 4962 |
* |
| 4963 |
* 9. Setup and register with mac80211 and debugfs |
| 4964 |
**************************************************/ |
| 4965 |
err = il4965_mac_setup_register(il, max_probe_length); |
| 4966 |
if (err) |
| 4967 |
goto out_unbind; |
| 4968 |
|
| 4969 |
il_dbgfs_register(il, DRV_NAME); |
| 4970 |
|
| 4971 |
err = sysfs_create_group(&il->pci_dev->dev.kobj, &il_attribute_group); |
| 4972 |
if (err) { |
| 4973 |
IL_ERR("failed to create sysfs device attributes\n"); |
| 4974 |
goto out_unbind; |
| 4975 |
} |
| 4976 |
|
| 4977 |
/* We have our copies now, allow OS release its copies */ |
| 4978 |
release_firmware(ucode_raw); |
| 4979 |
complete(&il->_4965.firmware_loading_complete); |
| 4980 |
return; |
| 4981 |
|
| 4982 |
try_again: |
| 4983 |
/* try next, if any */ |
| 4984 |
if (il4965_request_firmware(il, false)) |
| 4985 |
goto out_unbind; |
| 4986 |
release_firmware(ucode_raw); |
| 4987 |
return; |
| 4988 |
|
| 4989 |
err_pci_alloc: |
| 4990 |
IL_ERR("failed to allocate pci memory\n"); |
| 4991 |
il4965_dealloc_ucode_pci(il); |
| 4992 |
out_unbind: |
| 4993 |
complete(&il->_4965.firmware_loading_complete); |
| 4994 |
device_release_driver(&il->pci_dev->dev); |
| 4995 |
release_firmware(ucode_raw); |
| 4996 |
} |
| 4997 |
|
| 4998 |
static const char *const desc_lookup_text[] = { |
| 4999 |
"OK", |
| 5000 |
"FAIL", |
| 5001 |
"BAD_PARAM", |
| 5002 |
"BAD_CHECKSUM", |
| 5003 |
"NMI_INTERRUPT_WDG", |
| 5004 |
"SYSASSERT", |
| 5005 |
"FATAL_ERROR", |
| 5006 |
"BAD_COMMAND", |
| 5007 |
"HW_ERROR_TUNE_LOCK", |
| 5008 |
"HW_ERROR_TEMPERATURE", |
| 5009 |
"ILLEGAL_CHAN_FREQ", |
| 5010 |
"VCC_NOT_STBL", |
| 5011 |
"FH49_ERROR", |
| 5012 |
"NMI_INTERRUPT_HOST", |
| 5013 |
"NMI_INTERRUPT_ACTION_PT", |
| 5014 |
"NMI_INTERRUPT_UNKNOWN", |
| 5015 |
"UCODE_VERSION_MISMATCH", |
| 5016 |
"HW_ERROR_ABS_LOCK", |
| 5017 |
"HW_ERROR_CAL_LOCK_FAIL", |
| 5018 |
"NMI_INTERRUPT_INST_ACTION_PT", |
| 5019 |
"NMI_INTERRUPT_DATA_ACTION_PT", |
| 5020 |
"NMI_TRM_HW_ER", |
| 5021 |
"NMI_INTERRUPT_TRM", |
| 5022 |
"NMI_INTERRUPT_BREAK_POINT", |
| 5023 |
"DEBUG_0", |
| 5024 |
"DEBUG_1", |
| 5025 |
"DEBUG_2", |
| 5026 |
"DEBUG_3", |
| 5027 |
}; |
| 5028 |
|
| 5029 |
static struct { |
| 5030 |
char *name; |
| 5031 |
u8 num; |
| 5032 |
} advanced_lookup[] = { |
| 5033 |
{ |
| 5034 |
"NMI_INTERRUPT_WDG", 0x34}, { |
| 5035 |
"SYSASSERT", 0x35}, { |
| 5036 |
"UCODE_VERSION_MISMATCH", 0x37}, { |
| 5037 |
"BAD_COMMAND", 0x38}, { |
| 5038 |
"NMI_INTERRUPT_DATA_ACTION_PT", 0x3C}, { |
| 5039 |
"FATAL_ERROR", 0x3D}, { |
| 5040 |
"NMI_TRM_HW_ERR", 0x46}, { |
| 5041 |
"NMI_INTERRUPT_TRM", 0x4C}, { |
| 5042 |
"NMI_INTERRUPT_BREAK_POINT", 0x54}, { |
| 5043 |
"NMI_INTERRUPT_WDG_RXF_FULL", 0x5C}, { |
| 5044 |
"NMI_INTERRUPT_WDG_NO_RBD_RXF_FULL", 0x64}, { |
| 5045 |
"NMI_INTERRUPT_HOST", 0x66}, { |
| 5046 |
"NMI_INTERRUPT_ACTION_PT", 0x7C}, { |
| 5047 |
"NMI_INTERRUPT_UNKNOWN", 0x84}, { |
| 5048 |
"NMI_INTERRUPT_INST_ACTION_PT", 0x86}, { |
| 5049 |
"ADVANCED_SYSASSERT", 0},}; |
| 5050 |
|
| 5051 |
static const char * |
| 5052 |
il4965_desc_lookup(u32 num) |
| 5053 |
{ |
| 5054 |
int i; |
| 5055 |
int max = ARRAY_SIZE(desc_lookup_text); |
| 5056 |
|
| 5057 |
if (num < max) |
| 5058 |
return desc_lookup_text[num]; |
| 5059 |
|
| 5060 |
max = ARRAY_SIZE(advanced_lookup) - 1; |
| 5061 |
for (i = 0; i < max; i++) { |
| 5062 |
if (advanced_lookup[i].num == num) |
| 5063 |
break; |
| 5064 |
} |
| 5065 |
return advanced_lookup[i].name; |
| 5066 |
} |
| 5067 |
|
| 5068 |
#define ERROR_START_OFFSET (1 * sizeof(u32)) |
| 5069 |
#define ERROR_ELEM_SIZE (7 * sizeof(u32)) |
| 5070 |
|
| 5071 |
void |
| 5072 |
il4965_dump_nic_error_log(struct il_priv *il) |
| 5073 |
{ |
| 5074 |
u32 data2, line; |
| 5075 |
u32 desc, time, count, base, data1; |
| 5076 |
u32 blink1, blink2, ilink1, ilink2; |
| 5077 |
u32 pc, hcmd; |
| 5078 |
|
| 5079 |
if (il->ucode_type == UCODE_INIT) |
| 5080 |
base = le32_to_cpu(il->card_alive_init.error_event_table_ptr); |
| 5081 |
else |
| 5082 |
base = le32_to_cpu(il->card_alive.error_event_table_ptr); |
| 5083 |
|
| 5084 |
if (!il->ops->is_valid_rtc_data_addr(base)) { |
| 5085 |
IL_ERR("Not valid error log pointer 0x%08X for %s uCode\n", |
| 5086 |
base, (il->ucode_type == UCODE_INIT) ? "Init" : "RT"); |
| 5087 |
return; |
| 5088 |
} |
| 5089 |
|
| 5090 |
count = il_read_targ_mem(il, base); |
| 5091 |
|
| 5092 |
if (ERROR_START_OFFSET <= count * ERROR_ELEM_SIZE) { |
| 5093 |
IL_ERR("Start IWL Error Log Dump:\n"); |
| 5094 |
IL_ERR("Status: 0x%08lX, count: %d\n", il->status, count); |
| 5095 |
} |
| 5096 |
|
| 5097 |
desc = il_read_targ_mem(il, base + 1 * sizeof(u32)); |
| 5098 |
il->isr_stats.err_code = desc; |
| 5099 |
pc = il_read_targ_mem(il, base + 2 * sizeof(u32)); |
| 5100 |
blink1 = il_read_targ_mem(il, base + 3 * sizeof(u32)); |
| 5101 |
blink2 = il_read_targ_mem(il, base + 4 * sizeof(u32)); |
| 5102 |
ilink1 = il_read_targ_mem(il, base + 5 * sizeof(u32)); |
| 5103 |
ilink2 = il_read_targ_mem(il, base + 6 * sizeof(u32)); |
| 5104 |
data1 = il_read_targ_mem(il, base + 7 * sizeof(u32)); |
| 5105 |
data2 = il_read_targ_mem(il, base + 8 * sizeof(u32)); |
| 5106 |
line = il_read_targ_mem(il, base + 9 * sizeof(u32)); |
| 5107 |
time = il_read_targ_mem(il, base + 11 * sizeof(u32)); |
| 5108 |
hcmd = il_read_targ_mem(il, base + 22 * sizeof(u32)); |
| 5109 |
|
| 5110 |
IL_ERR("Desc Time " |
| 5111 |
"data1 data2 line\n"); |
| 5112 |
IL_ERR("%-28s (0x%04X) %010u 0x%08X 0x%08X %u\n", |
| 5113 |
il4965_desc_lookup(desc), desc, time, data1, data2, line); |
| 5114 |
IL_ERR("pc blink1 blink2 ilink1 ilink2 hcmd\n"); |
| 5115 |
IL_ERR("0x%05X 0x%05X 0x%05X 0x%05X 0x%05X 0x%05X\n", pc, blink1, |
| 5116 |
blink2, ilink1, ilink2, hcmd); |
| 5117 |
} |
| 5118 |
|
| 5119 |
static void |
| 5120 |
il4965_rf_kill_ct_config(struct il_priv *il) |
| 5121 |
{ |
| 5122 |
struct il_ct_kill_config cmd; |
| 5123 |
unsigned long flags; |
| 5124 |
int ret = 0; |
| 5125 |
|
| 5126 |
spin_lock_irqsave(&il->lock, flags); |
| 5127 |
_il_wr(il, CSR_UCODE_DRV_GP1_CLR, |
| 5128 |
CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT); |
| 5129 |
spin_unlock_irqrestore(&il->lock, flags); |
| 5130 |
|
| 5131 |
cmd.critical_temperature_R = |
| 5132 |
cpu_to_le32(il->hw_params.ct_kill_threshold); |
| 5133 |
|
| 5134 |
ret = il_send_cmd_pdu(il, C_CT_KILL_CONFIG, sizeof(cmd), &cmd); |
| 5135 |
if (ret) |
| 5136 |
IL_ERR("C_CT_KILL_CONFIG failed\n"); |
| 5137 |
else |
| 5138 |
D_INFO("C_CT_KILL_CONFIG " "succeeded, " |
| 5139 |
"critical temperature is %d\n", |
| 5140 |
il->hw_params.ct_kill_threshold); |
| 5141 |
} |
| 5142 |
|
| 5143 |
static const s8 default_queue_to_tx_fifo[] = { |
| 5144 |
IL_TX_FIFO_VO, |
| 5145 |
IL_TX_FIFO_VI, |
| 5146 |
IL_TX_FIFO_BE, |
| 5147 |
IL_TX_FIFO_BK, |
| 5148 |
IL49_CMD_FIFO_NUM, |
| 5149 |
IL_TX_FIFO_UNUSED, |
| 5150 |
IL_TX_FIFO_UNUSED, |
| 5151 |
}; |
| 5152 |
|
| 5153 |
#define IL_MASK(lo, hi) ((1 << (hi)) | ((1 << (hi)) - (1 << (lo)))) |
| 5154 |
|
| 5155 |
static int |
| 5156 |
il4965_alive_notify(struct il_priv *il) |
| 5157 |
{ |
| 5158 |
u32 a; |
| 5159 |
unsigned long flags; |
| 5160 |
int i, chan; |
| 5161 |
u32 reg_val; |
| 5162 |
|
| 5163 |
spin_lock_irqsave(&il->lock, flags); |
| 5164 |
|
| 5165 |
/* Clear 4965's internal Tx Scheduler data base */ |
| 5166 |
il->scd_base_addr = il_rd_prph(il, IL49_SCD_SRAM_BASE_ADDR); |
| 5167 |
a = il->scd_base_addr + IL49_SCD_CONTEXT_DATA_OFFSET; |
| 5168 |
for (; a < il->scd_base_addr + IL49_SCD_TX_STTS_BITMAP_OFFSET; a += 4) |
| 5169 |
il_write_targ_mem(il, a, 0); |
| 5170 |
for (; a < il->scd_base_addr + IL49_SCD_TRANSLATE_TBL_OFFSET; a += 4) |
| 5171 |
il_write_targ_mem(il, a, 0); |
| 5172 |
for (; |
| 5173 |
a < |
| 5174 |
il->scd_base_addr + |
| 5175 |
IL49_SCD_TRANSLATE_TBL_OFFSET_QUEUE(il->hw_params.max_txq_num); |
| 5176 |
a += 4) |
| 5177 |
il_write_targ_mem(il, a, 0); |
| 5178 |
|
| 5179 |
/* Tel 4965 where to find Tx byte count tables */ |
| 5180 |
il_wr_prph(il, IL49_SCD_DRAM_BASE_ADDR, il->scd_bc_tbls.dma >> 10); |
| 5181 |
|
| 5182 |
/* Enable DMA channel */ |
| 5183 |
for (chan = 0; chan < FH49_TCSR_CHNL_NUM; chan++) |
| 5184 |
il_wr(il, FH49_TCSR_CHNL_TX_CONFIG_REG(chan), |
| 5185 |
FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE | |
| 5186 |
FH49_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE); |
| 5187 |
|
| 5188 |
/* Update FH chicken bits */ |
| 5189 |
reg_val = il_rd(il, FH49_TX_CHICKEN_BITS_REG); |
| 5190 |
il_wr(il, FH49_TX_CHICKEN_BITS_REG, |
| 5191 |
reg_val | FH49_TX_CHICKEN_BITS_SCD_AUTO_RETRY_EN); |
| 5192 |
|
| 5193 |
/* Disable chain mode for all queues */ |
| 5194 |
il_wr_prph(il, IL49_SCD_QUEUECHAIN_SEL, 0); |
| 5195 |
|
| 5196 |
/* Initialize each Tx queue (including the command queue) */ |
| 5197 |
for (i = 0; i < il->hw_params.max_txq_num; i++) { |
| 5198 |
|
| 5199 |
/* TFD circular buffer read/write idxes */ |
| 5200 |
il_wr_prph(il, IL49_SCD_QUEUE_RDPTR(i), 0); |
| 5201 |
il_wr(il, HBUS_TARG_WRPTR, 0 | (i << 8)); |
| 5202 |
|
| 5203 |
/* Max Tx Window size for Scheduler-ACK mode */ |
| 5204 |
il_write_targ_mem(il, |
| 5205 |
il->scd_base_addr + |
| 5206 |
IL49_SCD_CONTEXT_QUEUE_OFFSET(i), |
| 5207 |
(SCD_WIN_SIZE << |
| 5208 |
IL49_SCD_QUEUE_CTX_REG1_WIN_SIZE_POS) & |
| 5209 |
IL49_SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK); |
| 5210 |
|
| 5211 |
/* Frame limit */ |
| 5212 |
il_write_targ_mem(il, |
| 5213 |
il->scd_base_addr + |
| 5214 |
IL49_SCD_CONTEXT_QUEUE_OFFSET(i) + |
| 5215 |
sizeof(u32), |
| 5216 |
(SCD_FRAME_LIMIT << |
| 5217 |
IL49_SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS) & |
| 5218 |
IL49_SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK); |
| 5219 |
|
| 5220 |
} |
| 5221 |
il_wr_prph(il, IL49_SCD_INTERRUPT_MASK, |
| 5222 |
(1 << il->hw_params.max_txq_num) - 1); |
| 5223 |
|
| 5224 |
/* Activate all Tx DMA/FIFO channels */ |
| 5225 |
il4965_txq_set_sched(il, IL_MASK(0, 6)); |
| 5226 |
|
| 5227 |
il4965_set_wr_ptrs(il, IL_DEFAULT_CMD_QUEUE_NUM, 0); |
| 5228 |
|
| 5229 |
/* make sure all queue are not stopped */ |
| 5230 |
memset(&il->queue_stopped[0], 0, sizeof(il->queue_stopped)); |
| 5231 |
for (i = 0; i < 4; i++) |
| 5232 |
atomic_set(&il->queue_stop_count[i], 0); |
| 5233 |
|
| 5234 |
/* reset to 0 to enable all the queue first */ |
| 5235 |
il->txq_ctx_active_msk = 0; |
| 5236 |
/* Map each Tx/cmd queue to its corresponding fifo */ |
| 5237 |
BUILD_BUG_ON(ARRAY_SIZE(default_queue_to_tx_fifo) != 7); |
| 5238 |
|
| 5239 |
for (i = 0; i < ARRAY_SIZE(default_queue_to_tx_fifo); i++) { |
| 5240 |
int ac = default_queue_to_tx_fifo[i]; |
| 5241 |
|
| 5242 |
il_txq_ctx_activate(il, i); |
| 5243 |
|
| 5244 |
if (ac == IL_TX_FIFO_UNUSED) |
| 5245 |
continue; |
| 5246 |
|
| 5247 |
il4965_tx_queue_set_status(il, &il->txq[i], ac, 0); |
| 5248 |
} |
| 5249 |
|
| 5250 |
spin_unlock_irqrestore(&il->lock, flags); |
| 5251 |
|
| 5252 |
return 0; |
| 5253 |
} |
| 5254 |
|
| 5255 |
/* |
| 5256 |
* il4965_alive_start - called after N_ALIVE notification received |
| 5257 |
* from protocol/runtime uCode (initialization uCode's |
| 5258 |
* Alive gets handled by il_init_alive_start()). |
| 5259 |
*/ |
| 5260 |
static void |
| 5261 |
il4965_alive_start(struct il_priv *il) |
| 5262 |
{ |
| 5263 |
int ret = 0; |
| 5264 |
|
| 5265 |
D_INFO("Runtime Alive received.\n"); |
| 5266 |
|
| 5267 |
if (il->card_alive.is_valid != UCODE_VALID_OK) { |
| 5268 |
/* We had an error bringing up the hardware, so take it |
| 5269 |
* all the way back down so we can try again */ |
| 5270 |
D_INFO("Alive failed.\n"); |
| 5271 |
goto restart; |
| 5272 |
} |
| 5273 |
|
| 5274 |
/* Initialize uCode has loaded Runtime uCode ... verify inst image. |
| 5275 |
* This is a paranoid check, because we would not have gotten the |
| 5276 |
* "runtime" alive if code weren't properly loaded. */ |
| 5277 |
if (il4965_verify_ucode(il)) { |
| 5278 |
/* Runtime instruction load was bad; |
| 5279 |
* take it all the way back down so we can try again */ |
| 5280 |
D_INFO("Bad runtime uCode load.\n"); |
| 5281 |
goto restart; |
| 5282 |
} |
| 5283 |
|
| 5284 |
ret = il4965_alive_notify(il); |
| 5285 |
if (ret) { |
| 5286 |
IL_WARN("Could not complete ALIVE transition [ntf]: %d\n", ret); |
| 5287 |
goto restart; |
| 5288 |
} |
| 5289 |
|
| 5290 |
/* After the ALIVE response, we can send host commands to the uCode */ |
| 5291 |
set_bit(S_ALIVE, &il->status); |
| 5292 |
|
| 5293 |
/* Enable watchdog to monitor the driver tx queues */ |
| 5294 |
il_setup_watchdog(il); |
| 5295 |
|
| 5296 |
if (il_is_rfkill(il)) |
| 5297 |
return; |
| 5298 |
|
| 5299 |
ieee80211_wake_queues(il->hw); |
| 5300 |
|
| 5301 |
il->active_rate = RATES_MASK; |
| 5302 |
|
| 5303 |
il_power_update_mode(il, true); |
| 5304 |
D_INFO("Updated power mode\n"); |
| 5305 |
|
| 5306 |
if (il_is_associated(il)) { |
| 5307 |
struct il_rxon_cmd *active_rxon = |
| 5308 |
(struct il_rxon_cmd *)&il->active; |
| 5309 |
/* apply any changes in staging */ |
| 5310 |
il->staging.filter_flags |= RXON_FILTER_ASSOC_MSK; |
| 5311 |
active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK; |
| 5312 |
} else { |
| 5313 |
/* Initialize our rx_config data */ |
| 5314 |
il_connection_init_rx_config(il); |
| 5315 |
|
| 5316 |
if (il->ops->set_rxon_chain) |
| 5317 |
il->ops->set_rxon_chain(il); |
| 5318 |
} |
| 5319 |
|
| 5320 |
/* Configure bluetooth coexistence if enabled */ |
| 5321 |
il_send_bt_config(il); |
| 5322 |
|
| 5323 |
il4965_reset_run_time_calib(il); |
| 5324 |
|
| 5325 |
set_bit(S_READY, &il->status); |
| 5326 |
|
| 5327 |
/* Configure the adapter for unassociated operation */ |
| 5328 |
il_commit_rxon(il); |
| 5329 |
|
| 5330 |
/* At this point, the NIC is initialized and operational */ |
| 5331 |
il4965_rf_kill_ct_config(il); |
| 5332 |
|
| 5333 |
D_INFO("ALIVE processing complete.\n"); |
| 5334 |
wake_up(&il->wait_command_queue); |
| 5335 |
|
| 5336 |
return; |
| 5337 |
|
| 5338 |
restart: |
| 5339 |
queue_work(il->workqueue, &il->restart); |
| 5340 |
} |
| 5341 |
|
| 5342 |
static void il4965_cancel_deferred_work(struct il_priv *il); |
| 5343 |
|
| 5344 |
static void |
| 5345 |
__il4965_down(struct il_priv *il) |
| 5346 |
{ |
| 5347 |
unsigned long flags; |
| 5348 |
int exit_pending; |
| 5349 |
|
| 5350 |
D_INFO(DRV_NAME " is going down\n"); |
| 5351 |
|
| 5352 |
il_scan_cancel_timeout(il, 200); |
| 5353 |
|
| 5354 |
exit_pending = test_and_set_bit(S_EXIT_PENDING, &il->status); |
| 5355 |
|
| 5356 |
/* Stop TX queues watchdog. We need to have S_EXIT_PENDING bit set |
| 5357 |
* to prevent rearm timer */ |
| 5358 |
timer_delete_sync(&il->watchdog); |
| 5359 |
|
| 5360 |
il_clear_ucode_stations(il); |
| 5361 |
|
| 5362 |
/* FIXME: race conditions ? */ |
| 5363 |
spin_lock_irq(&il->sta_lock); |
| 5364 |
/* |
| 5365 |
* Remove all key information that is not stored as part |
| 5366 |
* of station information since mac80211 may not have had |
| 5367 |
* a chance to remove all the keys. When device is |
| 5368 |
* reconfigured by mac80211 after an error all keys will |
| 5369 |
* be reconfigured. |
| 5370 |
*/ |
| 5371 |
memset(il->_4965.wep_keys, 0, sizeof(il->_4965.wep_keys)); |
| 5372 |
il->_4965.key_mapping_keys = 0; |
| 5373 |
spin_unlock_irq(&il->sta_lock); |
| 5374 |
|
| 5375 |
il_dealloc_bcast_stations(il); |
| 5376 |
il_clear_driver_stations(il); |
| 5377 |
|
| 5378 |
/* Unblock any waiting calls */ |
| 5379 |
wake_up_all(&il->wait_command_queue); |
| 5380 |
|
| 5381 |
/* Wipe out the EXIT_PENDING status bit if we are not actually |
| 5382 |
* exiting the module */ |
| 5383 |
if (!exit_pending) |
| 5384 |
clear_bit(S_EXIT_PENDING, &il->status); |
| 5385 |
|
| 5386 |
/* stop and reset the on-board processor */ |
| 5387 |
_il_wr(il, CSR_RESET, CSR_RESET_REG_FLAG_NEVO_RESET); |
| 5388 |
|
| 5389 |
/* tell the device to stop sending interrupts */ |
| 5390 |
spin_lock_irqsave(&il->lock, flags); |
| 5391 |
il_disable_interrupts(il); |
| 5392 |
spin_unlock_irqrestore(&il->lock, flags); |
| 5393 |
il4965_synchronize_irq(il); |
| 5394 |
|
| 5395 |
if (il->mac80211_registered) |
| 5396 |
ieee80211_stop_queues(il->hw); |
| 5397 |
|
| 5398 |
/* If we have not previously called il_init() then |
| 5399 |
* clear all bits but the RF Kill bit and return */ |
| 5400 |
if (!il_is_init(il)) { |
| 5401 |
il->status = |
| 5402 |
test_bit(S_RFKILL, &il->status) << S_RFKILL | |
| 5403 |
test_bit(S_GEO_CONFIGURED, &il->status) << S_GEO_CONFIGURED | |
| 5404 |
test_bit(S_EXIT_PENDING, &il->status) << S_EXIT_PENDING; |
| 5405 |
goto exit; |
| 5406 |
} |
| 5407 |
|
| 5408 |
/* ...otherwise clear out all the status bits but the RF Kill |
| 5409 |
* bit and continue taking the NIC down. */ |
| 5410 |
il->status &= |
| 5411 |
test_bit(S_RFKILL, &il->status) << S_RFKILL | |
| 5412 |
test_bit(S_GEO_CONFIGURED, &il->status) << S_GEO_CONFIGURED | |
| 5413 |
test_bit(S_FW_ERROR, &il->status) << S_FW_ERROR | |
| 5414 |
test_bit(S_EXIT_PENDING, &il->status) << S_EXIT_PENDING; |
| 5415 |
|
| 5416 |
/* |
| 5417 |
* We disabled and synchronized interrupt, and priv->mutex is taken, so |
| 5418 |
* here is the only thread which will program device registers, but |
| 5419 |
* still have lockdep assertions, so we are taking reg_lock. |
| 5420 |
*/ |
| 5421 |
spin_lock_irq(&il->reg_lock); |
| 5422 |
/* FIXME: il_grab_nic_access if rfkill is off ? */ |
| 5423 |
|
| 5424 |
il4965_txq_ctx_stop(il); |
| 5425 |
il4965_rxq_stop(il); |
| 5426 |
/* Power-down device's busmaster DMA clocks */ |
| 5427 |
_il_wr_prph(il, APMG_CLK_DIS_REG, APMG_CLK_VAL_DMA_CLK_RQT); |
| 5428 |
udelay(5); |
| 5429 |
/* Make sure (redundant) we've released our request to stay awake */ |
| 5430 |
_il_clear_bit(il, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ); |
| 5431 |
/* Stop the device, and put it in low power state */ |
| 5432 |
_il_apm_stop(il); |
| 5433 |
|
| 5434 |
spin_unlock_irq(&il->reg_lock); |
| 5435 |
|
| 5436 |
il4965_txq_ctx_unmap(il); |
| 5437 |
exit: |
| 5438 |
memset(&il->card_alive, 0, sizeof(struct il_alive_resp)); |
| 5439 |
|
| 5440 |
dev_kfree_skb(il->beacon_skb); |
| 5441 |
il->beacon_skb = NULL; |
| 5442 |
|
| 5443 |
/* clear out any free frames */ |
| 5444 |
il4965_clear_free_frames(il); |
| 5445 |
} |
| 5446 |
|
| 5447 |
static void |
| 5448 |
il4965_down(struct il_priv *il) |
| 5449 |
{ |
| 5450 |
mutex_lock(&il->mutex); |
| 5451 |
__il4965_down(il); |
| 5452 |
mutex_unlock(&il->mutex); |
| 5453 |
|
| 5454 |
il4965_cancel_deferred_work(il); |
| 5455 |
} |
| 5456 |
|
| 5457 |
|
| 5458 |
static void |
| 5459 |
il4965_set_hw_ready(struct il_priv *il) |
| 5460 |
{ |
| 5461 |
int ret; |
| 5462 |
|
| 5463 |
il_set_bit(il, CSR_HW_IF_CONFIG_REG, |
| 5464 |
CSR_HW_IF_CONFIG_REG_BIT_NIC_READY); |
| 5465 |
|
| 5466 |
/* See if we got it */ |
| 5467 |
ret = _il_poll_bit(il, CSR_HW_IF_CONFIG_REG, |
| 5468 |
CSR_HW_IF_CONFIG_REG_BIT_NIC_READY, |
| 5469 |
CSR_HW_IF_CONFIG_REG_BIT_NIC_READY, |
| 5470 |
100); |
| 5471 |
if (ret >= 0) |
| 5472 |
il->hw_ready = true; |
| 5473 |
|
| 5474 |
D_INFO("hardware %s ready\n", (il->hw_ready) ? "" : "not"); |
| 5475 |
} |
| 5476 |
|
| 5477 |
static void |
| 5478 |
il4965_prepare_card_hw(struct il_priv *il) |
| 5479 |
{ |
| 5480 |
int ret; |
| 5481 |
|
| 5482 |
il->hw_ready = false; |
| 5483 |
|
| 5484 |
il4965_set_hw_ready(il); |
| 5485 |
if (il->hw_ready) |
| 5486 |
return; |
| 5487 |
|
| 5488 |
/* If HW is not ready, prepare the conditions to check again */ |
| 5489 |
il_set_bit(il, CSR_HW_IF_CONFIG_REG, CSR_HW_IF_CONFIG_REG_PREPARE); |
| 5490 |
|
| 5491 |
ret = |
| 5492 |
_il_poll_bit(il, CSR_HW_IF_CONFIG_REG, |
| 5493 |
~CSR_HW_IF_CONFIG_REG_BIT_NIC_PREPARE_DONE, |
| 5494 |
CSR_HW_IF_CONFIG_REG_BIT_NIC_PREPARE_DONE, 150000); |
| 5495 |
|
| 5496 |
/* HW should be ready by now, check again. */ |
| 5497 |
if (ret != -ETIMEDOUT) |
| 5498 |
il4965_set_hw_ready(il); |
| 5499 |
} |
| 5500 |
|
| 5501 |
#define MAX_HW_RESTARTS 5 |
| 5502 |
|
| 5503 |
static int |
| 5504 |
__il4965_up(struct il_priv *il) |
| 5505 |
{ |
| 5506 |
int i; |
| 5507 |
int ret; |
| 5508 |
|
| 5509 |
if (test_bit(S_EXIT_PENDING, &il->status)) { |
| 5510 |
IL_WARN("Exit pending; will not bring the NIC up\n"); |
| 5511 |
return -EIO; |
| 5512 |
} |
| 5513 |
|
| 5514 |
if (!il->ucode_data_backup.v_addr || !il->ucode_data.v_addr) { |
| 5515 |
IL_ERR("ucode not available for device bringup\n"); |
| 5516 |
return -EIO; |
| 5517 |
} |
| 5518 |
|
| 5519 |
ret = il4965_alloc_bcast_station(il); |
| 5520 |
if (ret) { |
| 5521 |
il_dealloc_bcast_stations(il); |
| 5522 |
return ret; |
| 5523 |
} |
| 5524 |
|
| 5525 |
il4965_prepare_card_hw(il); |
| 5526 |
if (!il->hw_ready) { |
| 5527 |
il_dealloc_bcast_stations(il); |
| 5528 |
IL_ERR("HW not ready\n"); |
| 5529 |
return -EIO; |
| 5530 |
} |
| 5531 |
|
| 5532 |
/* If platform's RF_KILL switch is NOT set to KILL */ |
| 5533 |
if (_il_rd(il, CSR_GP_CNTRL) & CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW) |
| 5534 |
clear_bit(S_RFKILL, &il->status); |
| 5535 |
else { |
| 5536 |
set_bit(S_RFKILL, &il->status); |
| 5537 |
wiphy_rfkill_set_hw_state(il->hw->wiphy, true); |
| 5538 |
|
| 5539 |
il_dealloc_bcast_stations(il); |
| 5540 |
il_enable_rfkill_int(il); |
| 5541 |
IL_WARN("Radio disabled by HW RF Kill switch\n"); |
| 5542 |
return 0; |
| 5543 |
} |
| 5544 |
|
| 5545 |
_il_wr(il, CSR_INT, 0xFFFFFFFF); |
| 5546 |
|
| 5547 |
/* must be initialised before il_hw_nic_init */ |
| 5548 |
il->cmd_queue = IL_DEFAULT_CMD_QUEUE_NUM; |
| 5549 |
|
| 5550 |
ret = il4965_hw_nic_init(il); |
| 5551 |
if (ret) { |
| 5552 |
IL_ERR("Unable to init nic\n"); |
| 5553 |
il_dealloc_bcast_stations(il); |
| 5554 |
return ret; |
| 5555 |
} |
| 5556 |
|
| 5557 |
/* make sure rfkill handshake bits are cleared */ |
| 5558 |
_il_wr(il, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL); |
| 5559 |
_il_wr(il, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED); |
| 5560 |
|
| 5561 |
/* clear (again), then enable host interrupts */ |
| 5562 |
_il_wr(il, CSR_INT, 0xFFFFFFFF); |
| 5563 |
il_enable_interrupts(il); |
| 5564 |
|
| 5565 |
/* really make sure rfkill handshake bits are cleared */ |
| 5566 |
_il_wr(il, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL); |
| 5567 |
_il_wr(il, CSR_UCODE_DRV_GP1_CLR, CSR_UCODE_SW_BIT_RFKILL); |
| 5568 |
|
| 5569 |
/* Copy original ucode data image from disk into backup cache. |
| 5570 |
* This will be used to initialize the on-board processor's |
| 5571 |
* data SRAM for a clean start when the runtime program first loads. */ |
| 5572 |
memcpy(il->ucode_data_backup.v_addr, il->ucode_data.v_addr, |
| 5573 |
il->ucode_data.len); |
| 5574 |
|
| 5575 |
for (i = 0; i < MAX_HW_RESTARTS; i++) { |
| 5576 |
|
| 5577 |
/* load bootstrap state machine, |
| 5578 |
* load bootstrap program into processor's memory, |
| 5579 |
* prepare to load the "initialize" uCode */ |
| 5580 |
ret = il->ops->load_ucode(il); |
| 5581 |
|
| 5582 |
if (ret) { |
| 5583 |
IL_ERR("Unable to set up bootstrap uCode: %d\n", ret); |
| 5584 |
continue; |
| 5585 |
} |
| 5586 |
|
| 5587 |
/* start card; "initialize" will load runtime ucode */ |
| 5588 |
il4965_nic_start(il); |
| 5589 |
|
| 5590 |
D_INFO(DRV_NAME " is coming up\n"); |
| 5591 |
|
| 5592 |
return 0; |
| 5593 |
} |
| 5594 |
|
| 5595 |
set_bit(S_EXIT_PENDING, &il->status); |
| 5596 |
__il4965_down(il); |
| 5597 |
clear_bit(S_EXIT_PENDING, &il->status); |
| 5598 |
|
| 5599 |
/* tried to restart and config the device for as long as our |
| 5600 |
* patience could withstand */ |
| 5601 |
IL_ERR("Unable to initialize device after %d attempts.\n", i); |
| 5602 |
return -EIO; |
| 5603 |
} |
| 5604 |
|
| 5605 |
/***************************************************************************** |
| 5606 |
* |
| 5607 |
* Workqueue callbacks |
| 5608 |
* |
| 5609 |
*****************************************************************************/ |
| 5610 |
|
| 5611 |
static void |
| 5612 |
il4965_bg_init_alive_start(struct work_struct *data) |
| 5613 |
{ |
| 5614 |
struct il_priv *il = |
| 5615 |
container_of(data, struct il_priv, init_alive_start.work); |
| 5616 |
|
| 5617 |
mutex_lock(&il->mutex); |
| 5618 |
if (test_bit(S_EXIT_PENDING, &il->status)) |
| 5619 |
goto out; |
| 5620 |
|
| 5621 |
il->ops->init_alive_start(il); |
| 5622 |
out: |
| 5623 |
mutex_unlock(&il->mutex); |
| 5624 |
} |
| 5625 |
|
| 5626 |
static void |
| 5627 |
il4965_bg_alive_start(struct work_struct *data) |
| 5628 |
{ |
| 5629 |
struct il_priv *il = |
| 5630 |
container_of(data, struct il_priv, alive_start.work); |
| 5631 |
|
| 5632 |
mutex_lock(&il->mutex); |
| 5633 |
if (test_bit(S_EXIT_PENDING, &il->status)) |
| 5634 |
goto out; |
| 5635 |
|
| 5636 |
il4965_alive_start(il); |
| 5637 |
out: |
| 5638 |
mutex_unlock(&il->mutex); |
| 5639 |
} |
| 5640 |
|
| 5641 |
static void |
| 5642 |
il4965_bg_run_time_calib_work(struct work_struct *work) |
| 5643 |
{ |
| 5644 |
struct il_priv *il = container_of(work, struct il_priv, |
| 5645 |
run_time_calib_work); |
| 5646 |
|
| 5647 |
mutex_lock(&il->mutex); |
| 5648 |
|
| 5649 |
if (test_bit(S_EXIT_PENDING, &il->status) || |
| 5650 |
test_bit(S_SCANNING, &il->status)) { |
| 5651 |
mutex_unlock(&il->mutex); |
| 5652 |
return; |
| 5653 |
} |
| 5654 |
|
| 5655 |
if (il->start_calib) { |
| 5656 |
il4965_chain_noise_calibration(il, (void *)&il->_4965.stats); |
| 5657 |
il4965_sensitivity_calibration(il, (void *)&il->_4965.stats); |
| 5658 |
} |
| 5659 |
|
| 5660 |
mutex_unlock(&il->mutex); |
| 5661 |
} |
| 5662 |
|
| 5663 |
static void |
| 5664 |
il4965_bg_restart(struct work_struct *data) |
| 5665 |
{ |
| 5666 |
struct il_priv *il = container_of(data, struct il_priv, restart); |
| 5667 |
|
| 5668 |
if (test_bit(S_EXIT_PENDING, &il->status)) |
| 5669 |
return; |
| 5670 |
|
| 5671 |
if (test_and_clear_bit(S_FW_ERROR, &il->status)) { |
| 5672 |
mutex_lock(&il->mutex); |
| 5673 |
il->is_open = 0; |
| 5674 |
|
| 5675 |
__il4965_down(il); |
| 5676 |
|
| 5677 |
mutex_unlock(&il->mutex); |
| 5678 |
il4965_cancel_deferred_work(il); |
| 5679 |
ieee80211_restart_hw(il->hw); |
| 5680 |
} else { |
| 5681 |
il4965_down(il); |
| 5682 |
|
| 5683 |
mutex_lock(&il->mutex); |
| 5684 |
if (test_bit(S_EXIT_PENDING, &il->status)) { |
| 5685 |
mutex_unlock(&il->mutex); |
| 5686 |
return; |
| 5687 |
} |
| 5688 |
|
| 5689 |
__il4965_up(il); |
| 5690 |
mutex_unlock(&il->mutex); |
| 5691 |
} |
| 5692 |
} |
| 5693 |
|
| 5694 |
static void |
| 5695 |
il4965_bg_rx_replenish(struct work_struct *data) |
| 5696 |
{ |
| 5697 |
struct il_priv *il = container_of(data, struct il_priv, rx_replenish); |
| 5698 |
|
| 5699 |
if (test_bit(S_EXIT_PENDING, &il->status)) |
| 5700 |
return; |
| 5701 |
|
| 5702 |
mutex_lock(&il->mutex); |
| 5703 |
il4965_rx_replenish(il); |
| 5704 |
mutex_unlock(&il->mutex); |
| 5705 |
} |
| 5706 |
|
| 5707 |
/***************************************************************************** |
| 5708 |
* |
| 5709 |
* mac80211 entry point functions |
| 5710 |
* |
| 5711 |
*****************************************************************************/ |
| 5712 |
|
| 5713 |
#define UCODE_READY_TIMEOUT (4 * HZ) |
| 5714 |
|
| 5715 |
/* |
| 5716 |
* Not a mac80211 entry point function, but it fits in with all the |
| 5717 |
* other mac80211 functions grouped here. |
| 5718 |
*/ |
| 5719 |
static int |
| 5720 |
il4965_mac_setup_register(struct il_priv *il, u32 max_probe_length) |
| 5721 |
{ |
| 5722 |
int ret; |
| 5723 |
struct ieee80211_hw *hw = il->hw; |
| 5724 |
|
| 5725 |
hw->rate_control_algorithm = "iwl-4965-rs"; |
| 5726 |
|
| 5727 |
/* Tell mac80211 our characteristics */ |
| 5728 |
ieee80211_hw_set(hw, SUPPORTS_DYNAMIC_PS); |
| 5729 |
ieee80211_hw_set(hw, SUPPORTS_PS); |
| 5730 |
ieee80211_hw_set(hw, REPORTS_TX_ACK_STATUS); |
| 5731 |
ieee80211_hw_set(hw, SPECTRUM_MGMT); |
| 5732 |
ieee80211_hw_set(hw, NEED_DTIM_BEFORE_ASSOC); |
| 5733 |
ieee80211_hw_set(hw, SIGNAL_DBM); |
| 5734 |
ieee80211_hw_set(hw, AMPDU_AGGREGATION); |
| 5735 |
if (il->cfg->sku & IL_SKU_N) |
| 5736 |
hw->wiphy->features |= NL80211_FEATURE_DYNAMIC_SMPS | |
| 5737 |
NL80211_FEATURE_STATIC_SMPS; |
| 5738 |
|
| 5739 |
hw->sta_data_size = sizeof(struct il_station_priv); |
| 5740 |
hw->vif_data_size = sizeof(struct il_vif_priv); |
| 5741 |
|
| 5742 |
hw->wiphy->interface_modes = |
| 5743 |
BIT(NL80211_IFTYPE_STATION) | BIT(NL80211_IFTYPE_ADHOC); |
| 5744 |
|
| 5745 |
hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN; |
| 5746 |
hw->wiphy->regulatory_flags |= REGULATORY_CUSTOM_REG | |
| 5747 |
REGULATORY_DISABLE_BEACON_HINTS; |
| 5748 |
|
| 5749 |
/* |
| 5750 |
* For now, disable PS by default because it affects |
| 5751 |
* RX performance significantly. |
| 5752 |
*/ |
| 5753 |
hw->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT; |
| 5754 |
|
| 5755 |
hw->wiphy->max_scan_ssids = PROBE_OPTION_MAX; |
| 5756 |
/* we create the 802.11 header and a zero-length SSID element */ |
| 5757 |
hw->wiphy->max_scan_ie_len = max_probe_length - 24 - 2; |
| 5758 |
|
| 5759 |
/* Default value; 4 EDCA QOS priorities */ |
| 5760 |
hw->queues = 4; |
| 5761 |
|
| 5762 |
hw->max_listen_interval = IL_CONN_MAX_LISTEN_INTERVAL; |
| 5763 |
|
| 5764 |
if (il->bands[NL80211_BAND_2GHZ].n_channels) |
| 5765 |
il->hw->wiphy->bands[NL80211_BAND_2GHZ] = |
| 5766 |
&il->bands[NL80211_BAND_2GHZ]; |
| 5767 |
if (il->bands[NL80211_BAND_5GHZ].n_channels) |
| 5768 |
il->hw->wiphy->bands[NL80211_BAND_5GHZ] = |
| 5769 |
&il->bands[NL80211_BAND_5GHZ]; |
| 5770 |
|
| 5771 |
il_leds_init(il); |
| 5772 |
|
| 5773 |
wiphy_ext_feature_set(il->hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); |
| 5774 |
|
| 5775 |
ret = ieee80211_register_hw(il->hw); |
| 5776 |
if (ret) { |
| 5777 |
IL_ERR("Failed to register hw (error %d)\n", ret); |
| 5778 |
return ret; |
| 5779 |
} |
| 5780 |
il->mac80211_registered = 1; |
| 5781 |
|
| 5782 |
return 0; |
| 5783 |
} |
| 5784 |
|
| 5785 |
int |
| 5786 |
il4965_mac_start(struct ieee80211_hw *hw) |
| 5787 |
{ |
| 5788 |
struct il_priv *il = hw->priv; |
| 5789 |
int ret; |
| 5790 |
|
| 5791 |
D_MAC80211("enter\n"); |
| 5792 |
|
| 5793 |
/* we should be verifying the device is ready to be opened */ |
| 5794 |
mutex_lock(&il->mutex); |
| 5795 |
ret = __il4965_up(il); |
| 5796 |
mutex_unlock(&il->mutex); |
| 5797 |
|
| 5798 |
if (ret) |
| 5799 |
return ret; |
| 5800 |
|
| 5801 |
if (il_is_rfkill(il)) |
| 5802 |
goto out; |
| 5803 |
|
| 5804 |
D_INFO("Start UP work done.\n"); |
| 5805 |
|
| 5806 |
/* Wait for START_ALIVE from Run Time ucode. Otherwise callbacks from |
| 5807 |
* mac80211 will not be run successfully. */ |
| 5808 |
ret = wait_event_timeout(il->wait_command_queue, |
| 5809 |
test_bit(S_READY, &il->status), |
| 5810 |
UCODE_READY_TIMEOUT); |
| 5811 |
if (!ret) { |
| 5812 |
if (!test_bit(S_READY, &il->status)) { |
| 5813 |
IL_ERR("START_ALIVE timeout after %dms.\n", |
| 5814 |
jiffies_to_msecs(UCODE_READY_TIMEOUT)); |
| 5815 |
return -ETIMEDOUT; |
| 5816 |
} |
| 5817 |
} |
| 5818 |
|
| 5819 |
il4965_led_enable(il); |
| 5820 |
|
| 5821 |
out: |
| 5822 |
il->is_open = 1; |
| 5823 |
D_MAC80211("leave\n"); |
| 5824 |
return 0; |
| 5825 |
} |
| 5826 |
|
| 5827 |
void |
| 5828 |
il4965_mac_stop(struct ieee80211_hw *hw, bool suspend) |
| 5829 |
{ |
| 5830 |
struct il_priv *il = hw->priv; |
| 5831 |
|
| 5832 |
D_MAC80211("enter\n"); |
| 5833 |
|
| 5834 |
if (!il->is_open) |
| 5835 |
return; |
| 5836 |
|
| 5837 |
il->is_open = 0; |
| 5838 |
|
| 5839 |
il4965_down(il); |
| 5840 |
|
| 5841 |
flush_workqueue(il->workqueue); |
| 5842 |
|
| 5843 |
/* User space software may expect getting rfkill changes |
| 5844 |
* even if interface is down */ |
| 5845 |
_il_wr(il, CSR_INT, 0xFFFFFFFF); |
| 5846 |
il_enable_rfkill_int(il); |
| 5847 |
|
| 5848 |
D_MAC80211("leave\n"); |
| 5849 |
} |
| 5850 |
|
| 5851 |
void |
| 5852 |
il4965_mac_tx(struct ieee80211_hw *hw, |
| 5853 |
struct ieee80211_tx_control *control, |
| 5854 |
struct sk_buff *skb) |
| 5855 |
{ |
| 5856 |
struct il_priv *il = hw->priv; |
| 5857 |
|
| 5858 |
D_MACDUMP("enter\n"); |
| 5859 |
|
| 5860 |
D_TX("dev->xmit(%d bytes) at rate 0x%02x\n", skb->len, |
| 5861 |
ieee80211_get_tx_rate(hw, IEEE80211_SKB_CB(skb))->bitrate); |
| 5862 |
|
| 5863 |
if (il4965_tx_skb(il, control->sta, skb)) |
| 5864 |
dev_kfree_skb_any(skb); |
| 5865 |
|
| 5866 |
D_MACDUMP("leave\n"); |
| 5867 |
} |
| 5868 |
|
| 5869 |
void |
| 5870 |
il4965_mac_update_tkip_key(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
| 5871 |
struct ieee80211_key_conf *keyconf, |
| 5872 |
struct ieee80211_sta *sta, u32 iv32, u16 * phase1key) |
| 5873 |
{ |
| 5874 |
struct il_priv *il = hw->priv; |
| 5875 |
|
| 5876 |
D_MAC80211("enter\n"); |
| 5877 |
|
| 5878 |
il4965_update_tkip_key(il, keyconf, sta, iv32, phase1key); |
| 5879 |
|
| 5880 |
D_MAC80211("leave\n"); |
| 5881 |
} |
| 5882 |
|
| 5883 |
int |
| 5884 |
il4965_mac_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, |
| 5885 |
struct ieee80211_vif *vif, struct ieee80211_sta *sta, |
| 5886 |
struct ieee80211_key_conf *key) |
| 5887 |
{ |
| 5888 |
struct il_priv *il = hw->priv; |
| 5889 |
int ret; |
| 5890 |
u8 sta_id; |
| 5891 |
bool is_default_wep_key = false; |
| 5892 |
|
| 5893 |
D_MAC80211("enter\n"); |
| 5894 |
|
| 5895 |
if (il->cfg->mod_params->sw_crypto) { |
| 5896 |
D_MAC80211("leave - hwcrypto disabled\n"); |
| 5897 |
return -EOPNOTSUPP; |
| 5898 |
} |
| 5899 |
|
| 5900 |
/* |
| 5901 |
* To support IBSS RSN, don't program group keys in IBSS, the |
| 5902 |
* hardware will then not attempt to decrypt the frames. |
| 5903 |
*/ |
| 5904 |
if (vif->type == NL80211_IFTYPE_ADHOC && |
| 5905 |
!(key->flags & IEEE80211_KEY_FLAG_PAIRWISE)) { |
| 5906 |
D_MAC80211("leave - ad-hoc group key\n"); |
| 5907 |
return -EOPNOTSUPP; |
| 5908 |
} |
| 5909 |
|
| 5910 |
sta_id = il_sta_id_or_broadcast(il, sta); |
| 5911 |
if (sta_id == IL_INVALID_STATION) |
| 5912 |
return -EINVAL; |
| 5913 |
|
| 5914 |
mutex_lock(&il->mutex); |
| 5915 |
il_scan_cancel_timeout(il, 100); |
| 5916 |
|
| 5917 |
/* |
| 5918 |
* If we are getting WEP group key and we didn't receive any key mapping |
| 5919 |
* so far, we are in legacy wep mode (group key only), otherwise we are |
| 5920 |
* in 1X mode. |
| 5921 |
* In legacy wep mode, we use another host command to the uCode. |
| 5922 |
*/ |
| 5923 |
if ((key->cipher == WLAN_CIPHER_SUITE_WEP40 || |
| 5924 |
key->cipher == WLAN_CIPHER_SUITE_WEP104) && !sta) { |
| 5925 |
if (cmd == SET_KEY) |
| 5926 |
is_default_wep_key = !il->_4965.key_mapping_keys; |
| 5927 |
else |
| 5928 |
is_default_wep_key = |
| 5929 |
(key->hw_key_idx == HW_KEY_DEFAULT); |
| 5930 |
} |
| 5931 |
|
| 5932 |
switch (cmd) { |
| 5933 |
case SET_KEY: |
| 5934 |
if (is_default_wep_key) |
| 5935 |
ret = il4965_set_default_wep_key(il, key); |
| 5936 |
else |
| 5937 |
ret = il4965_set_dynamic_key(il, key, sta_id); |
| 5938 |
|
| 5939 |
D_MAC80211("enable hwcrypto key\n"); |
| 5940 |
break; |
| 5941 |
case DISABLE_KEY: |
| 5942 |
if (is_default_wep_key) |
| 5943 |
ret = il4965_remove_default_wep_key(il, key); |
| 5944 |
else |
| 5945 |
ret = il4965_remove_dynamic_key(il, key, sta_id); |
| 5946 |
|
| 5947 |
D_MAC80211("disable hwcrypto key\n"); |
| 5948 |
break; |
| 5949 |
default: |
| 5950 |
ret = -EINVAL; |
| 5951 |
} |
| 5952 |
|
| 5953 |
mutex_unlock(&il->mutex); |
| 5954 |
D_MAC80211("leave\n"); |
| 5955 |
|
| 5956 |
return ret; |
| 5957 |
} |
| 5958 |
|
| 5959 |
int |
| 5960 |
il4965_mac_ampdu_action(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
| 5961 |
struct ieee80211_ampdu_params *params) |
| 5962 |
{ |
| 5963 |
struct il_priv *il = hw->priv; |
| 5964 |
int ret = -EINVAL; |
| 5965 |
struct ieee80211_sta *sta = params->sta; |
| 5966 |
enum ieee80211_ampdu_mlme_action action = params->action; |
| 5967 |
u16 tid = params->tid; |
| 5968 |
u16 *ssn = ¶ms->ssn; |
| 5969 |
|
| 5970 |
D_HT("A-MPDU action on addr %pM tid %d\n", sta->addr, tid); |
| 5971 |
|
| 5972 |
if (!(il->cfg->sku & IL_SKU_N)) |
| 5973 |
return -EACCES; |
| 5974 |
|
| 5975 |
mutex_lock(&il->mutex); |
| 5976 |
|
| 5977 |
switch (action) { |
| 5978 |
case IEEE80211_AMPDU_RX_START: |
| 5979 |
D_HT("start Rx\n"); |
| 5980 |
ret = il4965_sta_rx_agg_start(il, sta, tid, *ssn); |
| 5981 |
break; |
| 5982 |
case IEEE80211_AMPDU_RX_STOP: |
| 5983 |
D_HT("stop Rx\n"); |
| 5984 |
ret = il4965_sta_rx_agg_stop(il, sta, tid); |
| 5985 |
if (test_bit(S_EXIT_PENDING, &il->status)) |
| 5986 |
ret = 0; |
| 5987 |
break; |
| 5988 |
case IEEE80211_AMPDU_TX_START: |
| 5989 |
D_HT("start Tx\n"); |
| 5990 |
ret = il4965_tx_agg_start(il, vif, sta, tid, ssn); |
| 5991 |
break; |
| 5992 |
case IEEE80211_AMPDU_TX_STOP_CONT: |
| 5993 |
case IEEE80211_AMPDU_TX_STOP_FLUSH: |
| 5994 |
case IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: |
| 5995 |
D_HT("stop Tx\n"); |
| 5996 |
ret = il4965_tx_agg_stop(il, vif, sta, tid); |
| 5997 |
if (test_bit(S_EXIT_PENDING, &il->status)) |
| 5998 |
ret = 0; |
| 5999 |
break; |
| 6000 |
case IEEE80211_AMPDU_TX_OPERATIONAL: |
| 6001 |
ret = 0; |
| 6002 |
break; |
| 6003 |
} |
| 6004 |
mutex_unlock(&il->mutex); |
| 6005 |
|
| 6006 |
return ret; |
| 6007 |
} |
| 6008 |
|
| 6009 |
int |
| 6010 |
il4965_mac_sta_add(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
| 6011 |
struct ieee80211_sta *sta) |
| 6012 |
{ |
| 6013 |
struct il_priv *il = hw->priv; |
| 6014 |
struct il_station_priv *sta_priv = (void *)sta->drv_priv; |
| 6015 |
bool is_ap = vif->type == NL80211_IFTYPE_STATION; |
| 6016 |
int ret; |
| 6017 |
u8 sta_id; |
| 6018 |
|
| 6019 |
D_INFO("received request to add station %pM\n", sta->addr); |
| 6020 |
mutex_lock(&il->mutex); |
| 6021 |
D_INFO("proceeding to add station %pM\n", sta->addr); |
| 6022 |
sta_priv->common.sta_id = IL_INVALID_STATION; |
| 6023 |
|
| 6024 |
atomic_set(&sta_priv->pending_frames, 0); |
| 6025 |
|
| 6026 |
ret = |
| 6027 |
il_add_station_common(il, sta->addr, is_ap, sta, &sta_id); |
| 6028 |
if (ret) { |
| 6029 |
IL_ERR("Unable to add station %pM (%d)\n", sta->addr, ret); |
| 6030 |
/* Should we return success if return code is EEXIST ? */ |
| 6031 |
mutex_unlock(&il->mutex); |
| 6032 |
return ret; |
| 6033 |
} |
| 6034 |
|
| 6035 |
sta_priv->common.sta_id = sta_id; |
| 6036 |
|
| 6037 |
/* Initialize rate scaling */ |
| 6038 |
D_INFO("Initializing rate scaling for station %pM\n", sta->addr); |
| 6039 |
il4965_rs_rate_init(il, sta, sta_id); |
| 6040 |
mutex_unlock(&il->mutex); |
| 6041 |
|
| 6042 |
return 0; |
| 6043 |
} |
| 6044 |
|
| 6045 |
void |
| 6046 |
il4965_mac_channel_switch(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
| 6047 |
struct ieee80211_channel_switch *ch_switch) |
| 6048 |
{ |
| 6049 |
struct il_priv *il = hw->priv; |
| 6050 |
const struct il_channel_info *ch_info; |
| 6051 |
struct ieee80211_conf *conf = &hw->conf; |
| 6052 |
struct ieee80211_channel *channel = ch_switch->chandef.chan; |
| 6053 |
struct il_ht_config *ht_conf = &il->current_ht_config; |
| 6054 |
u16 ch; |
| 6055 |
|
| 6056 |
D_MAC80211("enter\n"); |
| 6057 |
|
| 6058 |
mutex_lock(&il->mutex); |
| 6059 |
|
| 6060 |
if (il_is_rfkill(il)) |
| 6061 |
goto out; |
| 6062 |
|
| 6063 |
if (test_bit(S_EXIT_PENDING, &il->status) || |
| 6064 |
test_bit(S_SCANNING, &il->status) || |
| 6065 |
test_bit(S_CHANNEL_SWITCH_PENDING, &il->status)) |
| 6066 |
goto out; |
| 6067 |
|
| 6068 |
if (!il_is_associated(il)) |
| 6069 |
goto out; |
| 6070 |
|
| 6071 |
if (!il->ops->set_channel_switch) |
| 6072 |
goto out; |
| 6073 |
|
| 6074 |
ch = channel->hw_value; |
| 6075 |
if (le16_to_cpu(il->active.channel) == ch) |
| 6076 |
goto out; |
| 6077 |
|
| 6078 |
ch_info = il_get_channel_info(il, channel->band, ch); |
| 6079 |
if (!il_is_channel_valid(ch_info)) { |
| 6080 |
D_MAC80211("invalid channel\n"); |
| 6081 |
goto out; |
| 6082 |
} |
| 6083 |
|
| 6084 |
spin_lock_irq(&il->lock); |
| 6085 |
|
| 6086 |
il->current_ht_config.smps = conf->smps_mode; |
| 6087 |
|
| 6088 |
/* Configure HT40 channels */ |
| 6089 |
switch (cfg80211_get_chandef_type(&ch_switch->chandef)) { |
| 6090 |
case NL80211_CHAN_NO_HT: |
| 6091 |
case NL80211_CHAN_HT20: |
| 6092 |
il->ht.is_40mhz = false; |
| 6093 |
il->ht.extension_chan_offset = IEEE80211_HT_PARAM_CHA_SEC_NONE; |
| 6094 |
break; |
| 6095 |
case NL80211_CHAN_HT40MINUS: |
| 6096 |
il->ht.extension_chan_offset = IEEE80211_HT_PARAM_CHA_SEC_BELOW; |
| 6097 |
il->ht.is_40mhz = true; |
| 6098 |
break; |
| 6099 |
case NL80211_CHAN_HT40PLUS: |
| 6100 |
il->ht.extension_chan_offset = IEEE80211_HT_PARAM_CHA_SEC_ABOVE; |
| 6101 |
il->ht.is_40mhz = true; |
| 6102 |
break; |
| 6103 |
} |
| 6104 |
|
| 6105 |
if ((le16_to_cpu(il->staging.channel) != ch)) |
| 6106 |
il->staging.flags = 0; |
| 6107 |
|
| 6108 |
il_set_rxon_channel(il, channel); |
| 6109 |
il_set_rxon_ht(il, ht_conf); |
| 6110 |
il_set_flags_for_band(il, channel->band, il->vif); |
| 6111 |
|
| 6112 |
spin_unlock_irq(&il->lock); |
| 6113 |
|
| 6114 |
il_set_rate(il); |
| 6115 |
/* |
| 6116 |
* at this point, staging_rxon has the |
| 6117 |
* configuration for channel switch |
| 6118 |
*/ |
| 6119 |
set_bit(S_CHANNEL_SWITCH_PENDING, &il->status); |
| 6120 |
il->switch_channel = cpu_to_le16(ch); |
| 6121 |
if (il->ops->set_channel_switch(il, ch_switch)) { |
| 6122 |
clear_bit(S_CHANNEL_SWITCH_PENDING, &il->status); |
| 6123 |
il->switch_channel = 0; |
| 6124 |
ieee80211_chswitch_done(il->vif, false, 0); |
| 6125 |
} |
| 6126 |
|
| 6127 |
out: |
| 6128 |
mutex_unlock(&il->mutex); |
| 6129 |
D_MAC80211("leave\n"); |
| 6130 |
} |
| 6131 |
|
| 6132 |
void |
| 6133 |
il4965_configure_filter(struct ieee80211_hw *hw, unsigned int changed_flags, |
| 6134 |
unsigned int *total_flags, u64 multicast) |
| 6135 |
{ |
| 6136 |
struct il_priv *il = hw->priv; |
| 6137 |
__le32 filter_or = 0, filter_nand = 0; |
| 6138 |
|
| 6139 |
#define CHK(test, flag) do { \ |
| 6140 |
if (*total_flags & (test)) \ |
| 6141 |
filter_or |= (flag); \ |
| 6142 |
else \ |
| 6143 |
filter_nand |= (flag); \ |
| 6144 |
} while (0) |
| 6145 |
|
| 6146 |
D_MAC80211("Enter: changed: 0x%x, total: 0x%x\n", changed_flags, |
| 6147 |
*total_flags); |
| 6148 |
|
| 6149 |
CHK(FIF_OTHER_BSS, RXON_FILTER_PROMISC_MSK); |
| 6150 |
/* Setting _just_ RXON_FILTER_CTL2HOST_MSK causes FH errors */ |
| 6151 |
CHK(FIF_CONTROL, RXON_FILTER_CTL2HOST_MSK | RXON_FILTER_PROMISC_MSK); |
| 6152 |
CHK(FIF_BCN_PRBRESP_PROMISC, RXON_FILTER_BCON_AWARE_MSK); |
| 6153 |
|
| 6154 |
#undef CHK |
| 6155 |
|
| 6156 |
mutex_lock(&il->mutex); |
| 6157 |
|
| 6158 |
il->staging.filter_flags &= ~filter_nand; |
| 6159 |
il->staging.filter_flags |= filter_or; |
| 6160 |
|
| 6161 |
/* |
| 6162 |
* Not committing directly because hardware can perform a scan, |
| 6163 |
* but we'll eventually commit the filter flags change anyway. |
| 6164 |
*/ |
| 6165 |
|
| 6166 |
mutex_unlock(&il->mutex); |
| 6167 |
|
| 6168 |
/* |
| 6169 |
* Receiving all multicast frames is always enabled by the |
| 6170 |
* default flags setup in il_connection_init_rx_config() |
| 6171 |
* since we currently do not support programming multicast |
| 6172 |
* filters into the device. |
| 6173 |
*/ |
| 6174 |
*total_flags &= |
| 6175 |
FIF_OTHER_BSS | FIF_ALLMULTI | |
| 6176 |
FIF_BCN_PRBRESP_PROMISC | FIF_CONTROL; |
| 6177 |
} |
| 6178 |
|
| 6179 |
/***************************************************************************** |
| 6180 |
* |
| 6181 |
* driver setup and teardown |
| 6182 |
* |
| 6183 |
*****************************************************************************/ |
| 6184 |
|
| 6185 |
static void |
| 6186 |
il4965_bg_txpower_work(struct work_struct *work) |
| 6187 |
{ |
| 6188 |
struct il_priv *il = container_of(work, struct il_priv, |
| 6189 |
txpower_work); |
| 6190 |
|
| 6191 |
mutex_lock(&il->mutex); |
| 6192 |
|
| 6193 |
/* If a scan happened to start before we got here |
| 6194 |
* then just return; the stats notification will |
| 6195 |
* kick off another scheduled work to compensate for |
| 6196 |
* any temperature delta we missed here. */ |
| 6197 |
if (test_bit(S_EXIT_PENDING, &il->status) || |
| 6198 |
test_bit(S_SCANNING, &il->status)) |
| 6199 |
goto out; |
| 6200 |
|
| 6201 |
/* Regardless of if we are associated, we must reconfigure the |
| 6202 |
* TX power since frames can be sent on non-radar channels while |
| 6203 |
* not associated */ |
| 6204 |
il->ops->send_tx_power(il); |
| 6205 |
|
| 6206 |
/* Update last_temperature to keep is_calib_needed from running |
| 6207 |
* when it isn't needed... */ |
| 6208 |
il->last_temperature = il->temperature; |
| 6209 |
out: |
| 6210 |
mutex_unlock(&il->mutex); |
| 6211 |
} |
| 6212 |
|
| 6213 |
static int |
| 6214 |
il4965_setup_deferred_work(struct il_priv *il) |
| 6215 |
{ |
| 6216 |
il->workqueue = create_singlethread_workqueue(DRV_NAME); |
| 6217 |
if (!il->workqueue) |
| 6218 |
return -ENOMEM; |
| 6219 |
|
| 6220 |
init_waitqueue_head(&il->wait_command_queue); |
| 6221 |
|
| 6222 |
INIT_WORK(&il->restart, il4965_bg_restart); |
| 6223 |
INIT_WORK(&il->rx_replenish, il4965_bg_rx_replenish); |
| 6224 |
INIT_WORK(&il->run_time_calib_work, il4965_bg_run_time_calib_work); |
| 6225 |
INIT_DELAYED_WORK(&il->init_alive_start, il4965_bg_init_alive_start); |
| 6226 |
INIT_DELAYED_WORK(&il->alive_start, il4965_bg_alive_start); |
| 6227 |
|
| 6228 |
il_setup_scan_deferred_work(il); |
| 6229 |
|
| 6230 |
INIT_WORK(&il->txpower_work, il4965_bg_txpower_work); |
| 6231 |
|
| 6232 |
timer_setup(&il->stats_periodic, il4965_bg_stats_periodic, 0); |
| 6233 |
|
| 6234 |
timer_setup(&il->watchdog, il_bg_watchdog, 0); |
| 6235 |
|
| 6236 |
tasklet_setup(&il->irq_tasklet, il4965_irq_tasklet); |
| 6237 |
|
| 6238 |
return 0; |
| 6239 |
} |
| 6240 |
|
| 6241 |
static void |
| 6242 |
il4965_cancel_deferred_work(struct il_priv *il) |
| 6243 |
{ |
| 6244 |
cancel_work_sync(&il->txpower_work); |
| 6245 |
cancel_delayed_work_sync(&il->init_alive_start); |
| 6246 |
cancel_delayed_work(&il->alive_start); |
| 6247 |
cancel_work_sync(&il->run_time_calib_work); |
| 6248 |
|
| 6249 |
il_cancel_scan_deferred_work(il); |
| 6250 |
|
| 6251 |
timer_delete_sync(&il->stats_periodic); |
| 6252 |
} |
| 6253 |
|
| 6254 |
static void |
| 6255 |
il4965_init_hw_rates(struct il_priv *il, struct ieee80211_rate *rates) |
| 6256 |
{ |
| 6257 |
int i; |
| 6258 |
|
| 6259 |
for (i = 0; i < RATE_COUNT_LEGACY; i++) { |
| 6260 |
rates[i].bitrate = il_rates[i].ieee * 5; |
| 6261 |
rates[i].hw_value = i; /* Rate scaling will work on idxes */ |
| 6262 |
rates[i].hw_value_short = i; |
| 6263 |
rates[i].flags = 0; |
| 6264 |
if ((i >= IL_FIRST_CCK_RATE) && (i <= IL_LAST_CCK_RATE)) { |
| 6265 |
/* |
| 6266 |
* If CCK != 1M then set short preamble rate flag. |
| 6267 |
*/ |
| 6268 |
rates[i].flags |= |
| 6269 |
(il_rates[i].plcp == |
| 6270 |
RATE_1M_PLCP) ? 0 : IEEE80211_RATE_SHORT_PREAMBLE; |
| 6271 |
} |
| 6272 |
} |
| 6273 |
} |
| 6274 |
|
| 6275 |
/* |
| 6276 |
* Acquire il->lock before calling this function ! |
| 6277 |
*/ |
| 6278 |
void |
| 6279 |
il4965_set_wr_ptrs(struct il_priv *il, int txq_id, u32 idx) |
| 6280 |
{ |
| 6281 |
il_wr(il, HBUS_TARG_WRPTR, (idx & 0xff) | (txq_id << 8)); |
| 6282 |
il_wr_prph(il, IL49_SCD_QUEUE_RDPTR(txq_id), idx); |
| 6283 |
} |
| 6284 |
|
| 6285 |
void |
| 6286 |
il4965_tx_queue_set_status(struct il_priv *il, struct il_tx_queue *txq, |
| 6287 |
int tx_fifo_id, int scd_retry) |
| 6288 |
{ |
| 6289 |
int txq_id = txq->q.id; |
| 6290 |
|
| 6291 |
/* Find out whether to activate Tx queue */ |
| 6292 |
int active = test_bit(txq_id, &il->txq_ctx_active_msk) ? 1 : 0; |
| 6293 |
|
| 6294 |
/* Set up and activate */ |
| 6295 |
il_wr_prph(il, IL49_SCD_QUEUE_STATUS_BITS(txq_id), |
| 6296 |
(active << IL49_SCD_QUEUE_STTS_REG_POS_ACTIVE) | |
| 6297 |
(tx_fifo_id << IL49_SCD_QUEUE_STTS_REG_POS_TXF) | |
| 6298 |
(scd_retry << IL49_SCD_QUEUE_STTS_REG_POS_WSL) | |
| 6299 |
(scd_retry << IL49_SCD_QUEUE_STTS_REG_POS_SCD_ACK) | |
| 6300 |
IL49_SCD_QUEUE_STTS_REG_MSK); |
| 6301 |
|
| 6302 |
txq->sched_retry = scd_retry; |
| 6303 |
|
| 6304 |
D_INFO("%s %s Queue %d on AC %d\n", active ? "Activate" : "Deactivate", |
| 6305 |
scd_retry ? "BA" : "AC", txq_id, tx_fifo_id); |
| 6306 |
} |
| 6307 |
|
| 6308 |
static const struct ieee80211_ops il4965_mac_ops = { |
| 6309 |
.add_chanctx = ieee80211_emulate_add_chanctx, |
| 6310 |
.remove_chanctx = ieee80211_emulate_remove_chanctx, |
| 6311 |
.change_chanctx = ieee80211_emulate_change_chanctx, |
| 6312 |
.switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx, |
| 6313 |
.tx = il4965_mac_tx, |
| 6314 |
.wake_tx_queue = ieee80211_handle_wake_tx_queue, |
| 6315 |
.start = il4965_mac_start, |
| 6316 |
.stop = il4965_mac_stop, |
| 6317 |
.add_interface = il_mac_add_interface, |
| 6318 |
.remove_interface = il_mac_remove_interface, |
| 6319 |
.change_interface = il_mac_change_interface, |
| 6320 |
.config = il_mac_config, |
| 6321 |
.configure_filter = il4965_configure_filter, |
| 6322 |
.set_key = il4965_mac_set_key, |
| 6323 |
.update_tkip_key = il4965_mac_update_tkip_key, |
| 6324 |
.conf_tx = il_mac_conf_tx, |
| 6325 |
.reset_tsf = il_mac_reset_tsf, |
| 6326 |
.bss_info_changed = il_mac_bss_info_changed, |
| 6327 |
.ampdu_action = il4965_mac_ampdu_action, |
| 6328 |
.hw_scan = il_mac_hw_scan, |
| 6329 |
.sta_add = il4965_mac_sta_add, |
| 6330 |
.sta_remove = il_mac_sta_remove, |
| 6331 |
.channel_switch = il4965_mac_channel_switch, |
| 6332 |
.tx_last_beacon = il_mac_tx_last_beacon, |
| 6333 |
.flush = il_mac_flush, |
| 6334 |
}; |
| 6335 |
|
| 6336 |
static int |
| 6337 |
il4965_init_drv(struct il_priv *il) |
| 6338 |
{ |
| 6339 |
int ret; |
| 6340 |
|
| 6341 |
spin_lock_init(&il->sta_lock); |
| 6342 |
spin_lock_init(&il->hcmd_lock); |
| 6343 |
|
| 6344 |
INIT_LIST_HEAD(&il->free_frames); |
| 6345 |
|
| 6346 |
mutex_init(&il->mutex); |
| 6347 |
|
| 6348 |
il->ieee_channels = NULL; |
| 6349 |
il->ieee_rates = NULL; |
| 6350 |
il->band = NL80211_BAND_2GHZ; |
| 6351 |
|
| 6352 |
il->iw_mode = NL80211_IFTYPE_STATION; |
| 6353 |
il->current_ht_config.smps = IEEE80211_SMPS_STATIC; |
| 6354 |
il->missed_beacon_threshold = IL_MISSED_BEACON_THRESHOLD_DEF; |
| 6355 |
|
| 6356 |
/* initialize force reset */ |
| 6357 |
il->force_reset.reset_duration = IL_DELAY_NEXT_FORCE_FW_RELOAD; |
| 6358 |
|
| 6359 |
/* Choose which receivers/antennas to use */ |
| 6360 |
if (il->ops->set_rxon_chain) |
| 6361 |
il->ops->set_rxon_chain(il); |
| 6362 |
|
| 6363 |
il_init_scan_params(il); |
| 6364 |
|
| 6365 |
ret = il_init_channel_map(il); |
| 6366 |
if (ret) { |
| 6367 |
IL_ERR("initializing regulatory failed: %d\n", ret); |
| 6368 |
goto err; |
| 6369 |
} |
| 6370 |
|
| 6371 |
ret = il_init_geos(il); |
| 6372 |
if (ret) { |
| 6373 |
IL_ERR("initializing geos failed: %d\n", ret); |
| 6374 |
goto err_free_channel_map; |
| 6375 |
} |
| 6376 |
il4965_init_hw_rates(il, il->ieee_rates); |
| 6377 |
|
| 6378 |
return 0; |
| 6379 |
|
| 6380 |
err_free_channel_map: |
| 6381 |
il_free_channel_map(il); |
| 6382 |
err: |
| 6383 |
return ret; |
| 6384 |
} |
| 6385 |
|
| 6386 |
static void |
| 6387 |
il4965_uninit_drv(struct il_priv *il) |
| 6388 |
{ |
| 6389 |
il_free_geos(il); |
| 6390 |
il_free_channel_map(il); |
| 6391 |
kfree(il->scan_cmd); |
| 6392 |
} |
| 6393 |
|
| 6394 |
static void |
| 6395 |
il4965_hw_detect(struct il_priv *il) |
| 6396 |
{ |
| 6397 |
il->hw_rev = _il_rd(il, CSR_HW_REV); |
| 6398 |
il->hw_wa_rev = _il_rd(il, CSR_HW_REV_WA_REG); |
| 6399 |
il->rev_id = il->pci_dev->revision; |
| 6400 |
D_INFO("HW Revision ID = 0x%X\n", il->rev_id); |
| 6401 |
} |
| 6402 |
|
| 6403 |
static const struct il_sensitivity_ranges il4965_sensitivity = { |
| 6404 |
.min_nrg_cck = 97, |
| 6405 |
.max_nrg_cck = 0, /* not used, set to 0 */ |
| 6406 |
|
| 6407 |
.auto_corr_min_ofdm = 85, |
| 6408 |
.auto_corr_min_ofdm_mrc = 170, |
| 6409 |
.auto_corr_min_ofdm_x1 = 105, |
| 6410 |
.auto_corr_min_ofdm_mrc_x1 = 220, |
| 6411 |
|
| 6412 |
.auto_corr_max_ofdm = 120, |
| 6413 |
.auto_corr_max_ofdm_mrc = 210, |
| 6414 |
.auto_corr_max_ofdm_x1 = 140, |
| 6415 |
.auto_corr_max_ofdm_mrc_x1 = 270, |
| 6416 |
|
| 6417 |
.auto_corr_min_cck = 125, |
| 6418 |
.auto_corr_max_cck = 200, |
| 6419 |
.auto_corr_min_cck_mrc = 200, |
| 6420 |
.auto_corr_max_cck_mrc = 400, |
| 6421 |
|
| 6422 |
.nrg_th_cck = 100, |
| 6423 |
.nrg_th_ofdm = 100, |
| 6424 |
|
| 6425 |
.barker_corr_th_min = 190, |
| 6426 |
.barker_corr_th_min_mrc = 390, |
| 6427 |
.nrg_th_cca = 62, |
| 6428 |
}; |
| 6429 |
|
| 6430 |
static void |
| 6431 |
il4965_set_hw_params(struct il_priv *il) |
| 6432 |
{ |
| 6433 |
il->hw_params.bcast_id = IL4965_BROADCAST_ID; |
| 6434 |
il->hw_params.max_rxq_size = RX_QUEUE_SIZE; |
| 6435 |
il->hw_params.max_rxq_log = RX_QUEUE_SIZE_LOG; |
| 6436 |
if (il->cfg->mod_params->amsdu_size_8K) |
| 6437 |
il->hw_params.rx_page_order = get_order(IL_RX_BUF_SIZE_8K); |
| 6438 |
else |
| 6439 |
il->hw_params.rx_page_order = get_order(IL_RX_BUF_SIZE_4K); |
| 6440 |
|
| 6441 |
il->hw_params.max_beacon_itrvl = IL_MAX_UCODE_BEACON_INTERVAL; |
| 6442 |
|
| 6443 |
if (il->cfg->mod_params->disable_11n) |
| 6444 |
il->cfg->sku &= ~IL_SKU_N; |
| 6445 |
|
| 6446 |
if (il->cfg->mod_params->num_of_queues >= IL_MIN_NUM_QUEUES && |
| 6447 |
il->cfg->mod_params->num_of_queues <= IL49_NUM_QUEUES) |
| 6448 |
il->cfg->num_of_queues = |
| 6449 |
il->cfg->mod_params->num_of_queues; |
| 6450 |
|
| 6451 |
il->hw_params.max_txq_num = il->cfg->num_of_queues; |
| 6452 |
il->hw_params.dma_chnl_num = FH49_TCSR_CHNL_NUM; |
| 6453 |
il->hw_params.scd_bc_tbls_size = |
| 6454 |
il->cfg->num_of_queues * |
| 6455 |
sizeof(struct il4965_scd_bc_tbl); |
| 6456 |
|
| 6457 |
il->hw_params.tfd_size = sizeof(struct il_tfd); |
| 6458 |
il->hw_params.max_stations = IL4965_STATION_COUNT; |
| 6459 |
il->hw_params.max_data_size = IL49_RTC_DATA_SIZE; |
| 6460 |
il->hw_params.max_inst_size = IL49_RTC_INST_SIZE; |
| 6461 |
il->hw_params.max_bsm_size = BSM_SRAM_SIZE; |
| 6462 |
il->hw_params.ht40_channel = BIT(NL80211_BAND_5GHZ); |
| 6463 |
|
| 6464 |
il->hw_params.rx_wrt_ptr_reg = FH49_RSCSR_CHNL0_WPTR; |
| 6465 |
|
| 6466 |
il->hw_params.tx_chains_num = il4965_num_of_ant(il->cfg->valid_tx_ant); |
| 6467 |
il->hw_params.rx_chains_num = il4965_num_of_ant(il->cfg->valid_rx_ant); |
| 6468 |
il->hw_params.valid_tx_ant = il->cfg->valid_tx_ant; |
| 6469 |
il->hw_params.valid_rx_ant = il->cfg->valid_rx_ant; |
| 6470 |
|
| 6471 |
il->hw_params.ct_kill_threshold = |
| 6472 |
celsius_to_kelvin(CT_KILL_THRESHOLD_LEGACY); |
| 6473 |
|
| 6474 |
il->hw_params.sens = &il4965_sensitivity; |
| 6475 |
il->hw_params.beacon_time_tsf_bits = IL4965_EXT_BEACON_TIME_POS; |
| 6476 |
} |
| 6477 |
|
| 6478 |
static int |
| 6479 |
il4965_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) |
| 6480 |
{ |
| 6481 |
int err = 0; |
| 6482 |
struct il_priv *il; |
| 6483 |
struct ieee80211_hw *hw; |
| 6484 |
struct il_cfg *cfg = (struct il_cfg *)(ent->driver_data); |
| 6485 |
unsigned long flags; |
| 6486 |
u16 pci_cmd; |
| 6487 |
|
| 6488 |
/************************ |
| 6489 |
* 1. Allocating HW data |
| 6490 |
************************/ |
| 6491 |
|
| 6492 |
hw = ieee80211_alloc_hw(sizeof(struct il_priv), &il4965_mac_ops); |
| 6493 |
if (!hw) { |
| 6494 |
err = -ENOMEM; |
| 6495 |
goto out; |
| 6496 |
} |
| 6497 |
il = hw->priv; |
| 6498 |
il->hw = hw; |
| 6499 |
SET_IEEE80211_DEV(hw, &pdev->dev); |
| 6500 |
|
| 6501 |
D_INFO("*** LOAD DRIVER ***\n"); |
| 6502 |
il->cfg = cfg; |
| 6503 |
il->ops = &il4965_ops; |
| 6504 |
#ifdef CONFIG_IWLEGACY_DEBUGFS |
| 6505 |
il->debugfs_ops = &il4965_debugfs_ops; |
| 6506 |
#endif |
| 6507 |
il->pci_dev = pdev; |
| 6508 |
il->inta_mask = CSR_INI_SET_MASK; |
| 6509 |
|
| 6510 |
/************************** |
| 6511 |
* 2. Initializing PCI bus |
| 6512 |
**************************/ |
| 6513 |
pci_disable_link_state(pdev, |
| 6514 |
PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1 | |
| 6515 |
PCIE_LINK_STATE_CLKPM); |
| 6516 |
|
| 6517 |
if (pci_enable_device(pdev)) { |
| 6518 |
err = -ENODEV; |
| 6519 |
goto out_ieee80211_free_hw; |
| 6520 |
} |
| 6521 |
|
| 6522 |
pci_set_master(pdev); |
| 6523 |
|
| 6524 |
err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(36)); |
| 6525 |
if (err) { |
| 6526 |
err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); |
| 6527 |
/* both attempts failed: */ |
| 6528 |
if (err) { |
| 6529 |
IL_WARN("No suitable DMA available.\n"); |
| 6530 |
goto out_pci_disable_device; |
| 6531 |
} |
| 6532 |
} |
| 6533 |
|
| 6534 |
err = pci_request_regions(pdev, DRV_NAME); |
| 6535 |
if (err) |
| 6536 |
goto out_pci_disable_device; |
| 6537 |
|
| 6538 |
pci_set_drvdata(pdev, il); |
| 6539 |
|
| 6540 |
/*********************** |
| 6541 |
* 3. Read REV register |
| 6542 |
***********************/ |
| 6543 |
il->hw_base = pci_ioremap_bar(pdev, 0); |
| 6544 |
if (!il->hw_base) { |
| 6545 |
err = -ENODEV; |
| 6546 |
goto out_pci_release_regions; |
| 6547 |
} |
| 6548 |
|
| 6549 |
D_INFO("pci_resource_len = 0x%08llx\n", |
| 6550 |
(unsigned long long)pci_resource_len(pdev, 0)); |
| 6551 |
D_INFO("pci_resource_base = %p\n", il->hw_base); |
| 6552 |
|
| 6553 |
/* these spin locks will be used in apm_ops.init and EEPROM access |
| 6554 |
* we should init now |
| 6555 |
*/ |
| 6556 |
spin_lock_init(&il->reg_lock); |
| 6557 |
spin_lock_init(&il->lock); |
| 6558 |
|
| 6559 |
/* |
| 6560 |
* stop and reset the on-board processor just in case it is in a |
| 6561 |
* strange state ... like being left stranded by a primary kernel |
| 6562 |
* and this is now the kdump kernel trying to start up |
| 6563 |
*/ |
| 6564 |
_il_wr(il, CSR_RESET, CSR_RESET_REG_FLAG_NEVO_RESET); |
| 6565 |
|
| 6566 |
il4965_hw_detect(il); |
| 6567 |
IL_INFO("Detected %s, REV=0x%X\n", il->cfg->name, il->hw_rev); |
| 6568 |
|
| 6569 |
/* We disable the RETRY_TIMEOUT register (0x41) to keep |
| 6570 |
* PCI Tx retries from interfering with C3 CPU state */ |
| 6571 |
pci_write_config_byte(pdev, PCI_CFG_RETRY_TIMEOUT, 0x00); |
| 6572 |
|
| 6573 |
il4965_prepare_card_hw(il); |
| 6574 |
if (!il->hw_ready) { |
| 6575 |
IL_WARN("Failed, HW not ready\n"); |
| 6576 |
err = -EIO; |
| 6577 |
goto out_iounmap; |
| 6578 |
} |
| 6579 |
|
| 6580 |
/***************** |
| 6581 |
* 4. Read EEPROM |
| 6582 |
*****************/ |
| 6583 |
/* Read the EEPROM */ |
| 6584 |
err = il_eeprom_init(il); |
| 6585 |
if (err) { |
| 6586 |
IL_ERR("Unable to init EEPROM\n"); |
| 6587 |
goto out_iounmap; |
| 6588 |
} |
| 6589 |
err = il4965_eeprom_check_version(il); |
| 6590 |
if (err) |
| 6591 |
goto out_free_eeprom; |
| 6592 |
|
| 6593 |
/* extract MAC Address */ |
| 6594 |
il4965_eeprom_get_mac(il, il->addresses[0].addr); |
| 6595 |
D_INFO("MAC address: %pM\n", il->addresses[0].addr); |
| 6596 |
il->hw->wiphy->addresses = il->addresses; |
| 6597 |
il->hw->wiphy->n_addresses = 1; |
| 6598 |
|
| 6599 |
/************************ |
| 6600 |
* 5. Setup HW constants |
| 6601 |
************************/ |
| 6602 |
il4965_set_hw_params(il); |
| 6603 |
|
| 6604 |
/******************* |
| 6605 |
* 6. Setup il |
| 6606 |
*******************/ |
| 6607 |
|
| 6608 |
err = il4965_init_drv(il); |
| 6609 |
if (err) |
| 6610 |
goto out_free_eeprom; |
| 6611 |
/* At this point both hw and il are initialized. */ |
| 6612 |
|
| 6613 |
/******************** |
| 6614 |
* 7. Setup services |
| 6615 |
********************/ |
| 6616 |
spin_lock_irqsave(&il->lock, flags); |
| 6617 |
il_disable_interrupts(il); |
| 6618 |
spin_unlock_irqrestore(&il->lock, flags); |
| 6619 |
|
| 6620 |
pci_enable_msi(il->pci_dev); |
| 6621 |
|
| 6622 |
err = request_irq(il->pci_dev->irq, il_isr, IRQF_SHARED, DRV_NAME, il); |
| 6623 |
if (err) { |
| 6624 |
IL_ERR("Error allocating IRQ %d\n", il->pci_dev->irq); |
| 6625 |
goto out_disable_msi; |
| 6626 |
} |
| 6627 |
|
| 6628 |
err = il4965_setup_deferred_work(il); |
| 6629 |
if (err) |
| 6630 |
goto out_free_irq; |
| 6631 |
|
| 6632 |
il4965_setup_handlers(il); |
| 6633 |
|
| 6634 |
/********************************************* |
| 6635 |
* 8. Enable interrupts and read RFKILL state |
| 6636 |
*********************************************/ |
| 6637 |
|
| 6638 |
/* enable rfkill interrupt: hw bug w/a */ |
| 6639 |
pci_read_config_word(il->pci_dev, PCI_COMMAND, &pci_cmd); |
| 6640 |
if (pci_cmd & PCI_COMMAND_INTX_DISABLE) { |
| 6641 |
pci_cmd &= ~PCI_COMMAND_INTX_DISABLE; |
| 6642 |
pci_write_config_word(il->pci_dev, PCI_COMMAND, pci_cmd); |
| 6643 |
} |
| 6644 |
|
| 6645 |
il_enable_rfkill_int(il); |
| 6646 |
|
| 6647 |
/* If platform's RF_KILL switch is NOT set to KILL */ |
| 6648 |
if (_il_rd(il, CSR_GP_CNTRL) & CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW) |
| 6649 |
clear_bit(S_RFKILL, &il->status); |
| 6650 |
else |
| 6651 |
set_bit(S_RFKILL, &il->status); |
| 6652 |
|
| 6653 |
wiphy_rfkill_set_hw_state(il->hw->wiphy, |
| 6654 |
test_bit(S_RFKILL, &il->status)); |
| 6655 |
|
| 6656 |
il_power_initialize(il); |
| 6657 |
|
| 6658 |
init_completion(&il->_4965.firmware_loading_complete); |
| 6659 |
|
| 6660 |
err = il4965_request_firmware(il, true); |
| 6661 |
if (err) |
| 6662 |
goto out_destroy_workqueue; |
| 6663 |
|
| 6664 |
return 0; |
| 6665 |
|
| 6666 |
out_destroy_workqueue: |
| 6667 |
destroy_workqueue(il->workqueue); |
| 6668 |
il->workqueue = NULL; |
| 6669 |
out_free_irq: |
| 6670 |
free_irq(il->pci_dev->irq, il); |
| 6671 |
out_disable_msi: |
| 6672 |
pci_disable_msi(il->pci_dev); |
| 6673 |
il4965_uninit_drv(il); |
| 6674 |
out_free_eeprom: |
| 6675 |
il_eeprom_free(il); |
| 6676 |
out_iounmap: |
| 6677 |
iounmap(il->hw_base); |
| 6678 |
out_pci_release_regions: |
| 6679 |
pci_release_regions(pdev); |
| 6680 |
out_pci_disable_device: |
| 6681 |
pci_disable_device(pdev); |
| 6682 |
out_ieee80211_free_hw: |
| 6683 |
ieee80211_free_hw(il->hw); |
| 6684 |
out: |
| 6685 |
return err; |
| 6686 |
} |
| 6687 |
|
| 6688 |
static void |
| 6689 |
il4965_pci_remove(struct pci_dev *pdev) |
| 6690 |
{ |
| 6691 |
struct il_priv *il = pci_get_drvdata(pdev); |
| 6692 |
unsigned long flags; |
| 6693 |
|
| 6694 |
if (!il) |
| 6695 |
return; |
| 6696 |
|
| 6697 |
wait_for_completion(&il->_4965.firmware_loading_complete); |
| 6698 |
|
| 6699 |
D_INFO("*** UNLOAD DRIVER ***\n"); |
| 6700 |
|
| 6701 |
il_dbgfs_unregister(il); |
| 6702 |
sysfs_remove_group(&pdev->dev.kobj, &il_attribute_group); |
| 6703 |
|
| 6704 |
/* ieee80211_unregister_hw call wil cause il_mac_stop to |
| 6705 |
* be called and il4965_down since we are removing the device |
| 6706 |
* we need to set S_EXIT_PENDING bit. |
| 6707 |
*/ |
| 6708 |
set_bit(S_EXIT_PENDING, &il->status); |
| 6709 |
|
| 6710 |
il_leds_exit(il); |
| 6711 |
|
| 6712 |
if (il->mac80211_registered) { |
| 6713 |
ieee80211_unregister_hw(il->hw); |
| 6714 |
il->mac80211_registered = 0; |
| 6715 |
} else { |
| 6716 |
il4965_down(il); |
| 6717 |
} |
| 6718 |
|
| 6719 |
/* |
| 6720 |
* Make sure device is reset to low power before unloading driver. |
| 6721 |
* This may be redundant with il4965_down(), but there are paths to |
| 6722 |
* run il4965_down() without calling apm_ops.stop(), and there are |
| 6723 |
* paths to avoid running il4965_down() at all before leaving driver. |
| 6724 |
* This (inexpensive) call *makes sure* device is reset. |
| 6725 |
*/ |
| 6726 |
il_apm_stop(il); |
| 6727 |
|
| 6728 |
/* make sure we flush any pending irq or |
| 6729 |
* tasklet for the driver |
| 6730 |
*/ |
| 6731 |
spin_lock_irqsave(&il->lock, flags); |
| 6732 |
il_disable_interrupts(il); |
| 6733 |
spin_unlock_irqrestore(&il->lock, flags); |
| 6734 |
|
| 6735 |
il4965_synchronize_irq(il); |
| 6736 |
|
| 6737 |
il4965_dealloc_ucode_pci(il); |
| 6738 |
|
| 6739 |
if (il->rxq.bd) |
| 6740 |
il4965_rx_queue_free(il, &il->rxq); |
| 6741 |
il4965_hw_txq_ctx_free(il); |
| 6742 |
|
| 6743 |
il_eeprom_free(il); |
| 6744 |
|
| 6745 |
/*netif_stop_queue(dev); */ |
| 6746 |
|
| 6747 |
/* ieee80211_unregister_hw calls il_mac_stop, which flushes |
| 6748 |
* il->workqueue... so we can't take down the workqueue |
| 6749 |
* until now... */ |
| 6750 |
destroy_workqueue(il->workqueue); |
| 6751 |
il->workqueue = NULL; |
| 6752 |
|
| 6753 |
free_irq(il->pci_dev->irq, il); |
| 6754 |
pci_disable_msi(il->pci_dev); |
| 6755 |
iounmap(il->hw_base); |
| 6756 |
pci_release_regions(pdev); |
| 6757 |
pci_disable_device(pdev); |
| 6758 |
|
| 6759 |
il4965_uninit_drv(il); |
| 6760 |
|
| 6761 |
dev_kfree_skb(il->beacon_skb); |
| 6762 |
|
| 6763 |
ieee80211_free_hw(il->hw); |
| 6764 |
} |
| 6765 |
|
| 6766 |
/* |
| 6767 |
* Activate/Deactivate Tx DMA/FIFO channels according tx fifos mask |
| 6768 |
* must be called under il->lock and mac access |
| 6769 |
*/ |
| 6770 |
void |
| 6771 |
il4965_txq_set_sched(struct il_priv *il, u32 mask) |
| 6772 |
{ |
| 6773 |
il_wr_prph(il, IL49_SCD_TXFACT, mask); |
| 6774 |
} |
| 6775 |
|
| 6776 |
/***************************************************************************** |
| 6777 |
* |
| 6778 |
* driver and module entry point |
| 6779 |
* |
| 6780 |
*****************************************************************************/ |
| 6781 |
|
| 6782 |
/* Hardware specific file defines the PCI IDs table for that hardware module */ |
| 6783 |
static const struct pci_device_id il4965_hw_card_ids[] = { |
| 6784 |
{IL_PCI_DEVICE(0x4229, PCI_ANY_ID, il4965_cfg)}, |
| 6785 |
{IL_PCI_DEVICE(0x4230, PCI_ANY_ID, il4965_cfg)}, |
| 6786 |
{0} |
| 6787 |
}; |
| 6788 |
MODULE_DEVICE_TABLE(pci, il4965_hw_card_ids); |
| 6789 |
|
| 6790 |
static struct pci_driver il4965_driver = { |
| 6791 |
.name = DRV_NAME, |
| 6792 |
.id_table = il4965_hw_card_ids, |
| 6793 |
.probe = il4965_pci_probe, |
| 6794 |
.remove = il4965_pci_remove, |
| 6795 |
.driver.pm = IL_LEGACY_PM_OPS, |
| 6796 |
}; |
| 6797 |
|
| 6798 |
static int __init |
| 6799 |
il4965_init(void) |
| 6800 |
{ |
| 6801 |
|
| 6802 |
int ret; |
| 6803 |
pr_info(DRV_DESCRIPTION ", " DRV_VERSION "\n"); |
| 6804 |
pr_info(DRV_COPYRIGHT "\n"); |
| 6805 |
|
| 6806 |
ret = il4965_rate_control_register(); |
| 6807 |
if (ret) { |
| 6808 |
pr_err("Unable to register rate control algorithm: %d\n", ret); |
| 6809 |
return ret; |
| 6810 |
} |
| 6811 |
|
| 6812 |
ret = pci_register_driver(&il4965_driver); |
| 6813 |
if (ret) { |
| 6814 |
pr_err("Unable to initialize PCI module\n"); |
| 6815 |
goto error_register; |
| 6816 |
} |
| 6817 |
|
| 6818 |
return ret; |
| 6819 |
|
| 6820 |
error_register: |
| 6821 |
il4965_rate_control_unregister(); |
| 6822 |
return ret; |
| 6823 |
} |
| 6824 |
|
| 6825 |
static void __exit |
| 6826 |
il4965_exit(void) |
| 6827 |
{ |
| 6828 |
pci_unregister_driver(&il4965_driver); |
| 6829 |
il4965_rate_control_unregister(); |
| 6830 |
} |
| 6831 |
|
| 6832 |
module_exit(il4965_exit); |
| 6833 |
module_init(il4965_init); |
| 6834 |
|
| 6835 |
#ifdef CONFIG_IWLEGACY_DEBUG |
| 6836 |
module_param_named(debug, il_debug_level, uint, 0644); |
| 6837 |
MODULE_PARM_DESC(debug, "debug output mask"); |
| 6838 |
#endif |
| 6839 |
|
| 6840 |
module_param_named(swcrypto, il4965_mod_params.sw_crypto, int, 0444); |
| 6841 |
MODULE_PARM_DESC(swcrypto, "using crypto in software (default 0 [hardware])"); |
| 6842 |
module_param_named(queues_num, il4965_mod_params.num_of_queues, int, 0444); |
| 6843 |
MODULE_PARM_DESC(queues_num, "number of hw queues."); |
| 6844 |
module_param_named(11n_disable, il4965_mod_params.disable_11n, int, 0444); |
| 6845 |
MODULE_PARM_DESC(11n_disable, "disable 11n functionality"); |
| 6846 |
module_param_named(amsdu_size_8K, il4965_mod_params.amsdu_size_8K, int, 0444); |
| 6847 |
MODULE_PARM_DESC(amsdu_size_8K, "enable 8K amsdu size (default 0 [disabled])"); |
| 6848 |
module_param_named(fw_restart, il4965_mod_params.restart_fw, int, 0444); |
| 6849 |
MODULE_PARM_DESC(fw_restart, "restart firmware in case of error"); |